Miele WMR 861 Brief operating instructions
Before the first use
OPERATING THE WASHING MACHINE
CHANGING THE PROGRAMME SEQUENCE
3 5
1
2
Operating the washing machine
Washing
Changing the programme sequence
Programme chart
ɉɉɉBefore using the machine for the first
time, ensure that it is correctly installed
and connected.
Please read the separate operating
instructions supplied with the appliance.
When the washing machine is switched
on for the first time with the button, the
welcome screen ("Willkommen") will appear.
Setting the language
You will be asked to select the language
you require for the display.
ĺ Touch the or sensor until the
language you want appears in the
display.
ĺ Confirm the language with the OK sensor.
Removing the transit bars
A reminder to remove the transit bars will
appear in the display.
ĺ Confirm the messages with the OK
sensor.
Setting the time of day (if required)
The display for setting the time will appear.
ĺ Set the desired time format and the
current time of day.
Start the calibration programme
The following message appears in the
display:
Turn on the tap and start the Cottons 90°C
programme without any laundry.
ĺ Confirm the message with the OKsensor.
ĺ Turn on the tap.
ĺ Turn the programme selector to Cottons.
ĺ Press the Start/Stop button.
At the end of the programme the following
message will appear in the display:
Set up completed
1 Display with sensors
See points 10 to 15 for more information.
2 Start/Stop button
For starting the programme selected
and cancelling a programme once it has
started.
3 Temperature button
For selecting a temperature.
4 Spin speed button
For selecting the spin speed.
5 Delay start button
For selecting Delay start.
6 Extra option buttons
Various Extra options can be added to
the wash programme.
7 Programme selector
For selecting a wash programme.
8 PC optical interface
For service technicians.
9 button
For switching the washing machine on
and off. To save energy, the washing
machine will switch off automatically 15
minutes after the end of the programme /
Anti-crease phase or after being switched
on if no other selection is made.
Washing environmentally and economically
– To get the most out of your machine,
load the maximum dry load for the
programme you are using.
– When smaller amounts of laundry are
washed, the automatic load recognition
system will reduce the amount of water
and energy used.
– Use the Express 20 programme for
small, lightly soiled loads.
– Modern detergents enable washing at
reduced temperatures (e.g. 20°C). Use
appropriate temperature settings for
saving energy.
10 sensor
Scrolls down the list to the next option or
decreases a value.
11 OK sensor
Confirms the programme selected, a
value set or opens a sub-menu.
12 sensor
Scrolls up the list to the next option or
increases a value.
13 Dos sensor
Switches on automatic detergent
dispensing.
14 Cap sensor
Activates cap dosing via the detergent
dispenser drawer.
15 EcoFeedback sensor
Provides information about the
energy and water consumption of the
programme.
Sensors 10 to 12 light up when the display
can be operated via the sensors.
– For precise dispensing, use automatic
detergent dispensing.
– Selecting the highest possible spin
speed for the wash programme will
save energy when drying in a tumble
dryer afterwards.
1. Preparing the laundry
ĺ Empty all pockets.
ɉɉForeign objects (e.g. nails,
coins, paper clips, etc.) can
cause damage to garments and
components in the machine.
ĺ Sort the laundry by colour and by care label. Most
garments have a textile care label in the collar or side
seam.
ĺ Pre-treat stains and badly soiled areas (see the booklet
"Miele's guide to laundry care").
2. Selecting a programme
ĺ Switch on the washing machine with the button.
Selecting a programme via the programme selector
ĺ Turn the programme selector to the required
programme.
The load for the programme selected will appear in the
display. This will then be replaced by the standard display.
Selecting a programme using the programme
selector at the "Further programmes" position and
the display
ĺ Turn the programme selector to
the Further programmes setting.
Automatic plus
appears in the display.
ĺ Touch the or sensor until the programme you want
appears in the display.
ĺ Confirm the programme with the OK sensor.
The load for the programme selected will appear in the
display. Preset programme parameters will be displayed,
depending on the programme selected.
1 Detergent dispenser drawer
2 Control panel
3 Access to drain filter, drain pump
and emergency release
4 Door
5 Access panel for TwinDos
containers
3. Loading the washing machine
Opening the door
ĺ Take hold of the door and pull it
open.
ĺ Unfold the laundry and load
loosely in the drum.
Closing the door
ĺ Make sure that no items are
caught between the door and
the seal.
ĺ Shut the door with a gentle
swing.
4. Selecting programme settings
Selecting a temperature
ĺ Press the Temperature button.
ĺ Set the temperature you want with the and
sensors and confirm your selection with the OK sensor.
Selecting a spin speed
ĺ Press the Spin speed button.
ĺ Set the spin speed you want with the and sensors
and confirm your selection with the OK sensor.
Selecting Extra options
ĺ Press the button for the Extra option you want.
Switching on Delay start
The start of the programme can be delayed from 15
minutes up to a maximum of 24 hours. This allows you
to make use of night-time economy electricity rates, for
example.
5. Adding detergent
There are several options for adding
detergent.
TwinDos
– Miele 2 Phase System
The optimum amount of UltraPhase 1 and
UltraPhase 2 will be dispensed automatically
according to the colour mix of the load.
ĺ Press the Dos sensor.
ĺ Use the and sensors to select the
dosage mix (For white items or For coloured
items) and confirm your selection with the
OK sensor.
– Liquid detergent/Fabric softener
The most suitable agent will appear in the
display with a tick () beside it.
If both the agents present in the
containers are suitable (e.g. detergent for
coloured items and fabric softener), then
both agents will be selected.
ĺ Confirm the option displayed with the
OK sensor or select another detergent or
fabric softener with the and sensors.
Detergent dispenser drawer
ĺ Pull out the
detergent drawer
and add
detergent to the
compartments.
/
CapDosing
Three different types of capsule are available:
See "Detergent" in the operating
instructions for more information.
WASHING
Detergent for the pre-wash
Detergent for the main wash,
including Soak if selected
Fabric softener, liquid starch or
capsules
Fabric care (e.g. fabric softener)
Additives (e.g. detergent enhancers)
Detergent
6. Starting the programme - end
of the programme
Starting the programme
ĺ Press the flashing Start/Stop button.
The door will lock ( appears in the display)
and the programme will start.
At the end of the programme
The door is still locked during the Anticrease phase and the following will appear
alternately in the display:
Anti-crease and Press the Start/Stop
button, then unload the drum
ĺ Press the Start/Stop button. The door will
be unlocked.
ĺ Pull open the door.
ĺ Remove the laundry.
ɉɉCheck that all items have been
removed from the drum.
ĺ Check the folds
in the door seal
for any small
articles, e.g.
buttons, which
might be lodged
there.
ĺ Switch the washing machine off with the
button.
ĺ If applicable, remove the used capsule
from the detergent dispenser drawer.
Close the door. Otherwise there is
a danger of objects being placed
inadvertently in the drum. If these remain
unnoticed and were washed in the next
load, they could damage the laundry. An
open door is also a danger to pets and
children.
Cancelling a programme
ĺ Press the Start/Stop button.
The following will appear in the display:
Cancel programme
ĺ Touch the OK sensor.
The suds will be pumped away. Programme
cancelled will appear in the display.
ĺ Pull open the door.
ĺ Remove the laundry.
Selecting another programme
ĺ Close the door.
ĺ Select the programme you want.
ĺ Add detergent to the detergent dispenser
drawer, if necessary.
ĺ Press the Start/Stop button.
Changing a programme and
settings
Programme
After the start of a programme, it is
no longer possible to select a different
programme.
Temperature/Spin speed
The temperature can be changed within
the first five minutes, except in the Cottons
programme. The spin speed can be
changed right up to the start of the final
spin.
ĺ Press the Temperature or Spin speed
button.
ĺ Use the or and OK sensors to
change the temperature and spin speed.
Extra options
It is possible to select or deselect the Short
and Water plus Extra options up to five
minutes after the programme has started.
It is not possible to make any changes to
the programme or to cancel it if the safety
lock has been activated.
Interrupting a programme
ĺ Switch the washing machine off with the
button.
ĺ Switch the washing machine back on
with the button to continue with the
same programme.
Adding or removing laundry
after a programme has started
ĺ Press the Start/Stop button. The
following will appear in the display: Cancel
programme
ĺ Scroll up or down the list with the or
sensor to:
Add laundry
ĺ Touch the OK sensor.
The programme will stop and the door will
unlock.
ĺ Pull open the door.
ĺ Add or remove items.
ĺ Close the door.
ĺ Press the Start/Stop button.
The programme will continue.
The door cannot be opened if:
– the suds temperature is above 55°C.
– the water is above a certain level.
– the programme has reached the Spin
stage.
, , ,
, , ,
, , ,
, , ,
, ,
T-shirts etc.
9.0 Cold to 90°C Cottons, linens or cotton mix fabrics, e.g. table linen, towelling, underwear,
Load
(inkg) Temperature Items Options
Cottons
Programme
2.0 Cold to 40°C Machine-washable or hand-washable wool or wool blend fabric.
Minimum iron 4.0 Cold to 60°C Synthetic, mixed fibre and easy care cotton.
Delicates 3.0 Cold to 60°C Delicate garments made from synthetic fibre, mixed fibre, rayon and viscose.
Woollens
fabric such as Gore-Tex®, SYMPATEX®, WINDSTOPPER® etc.
Denim 3.0 Cold to 60°C Textiles made from denim.
Outerwear 2.5 Cold to 40°C Performance outerwear (e.g. jackets and trousers) made from membrane
programmes under names of your choice. The saved favourite programmes
– – You can save your own customised wash programmes as favourite
Favourite
programmes
will be sorted alphabetically. Please see "Favourite programmes" for more
information.
Depending
on the items
selected
,
is too small for a standard programme. You can choose from a list of 19
different items.
Mixed items – – A load consisting of various items with different garment care labels which
QuickPowerWash 5.0 60°C to 40°C Moderately soiled garments which are also suitable for washing in the
Cottons programme.
, ,
or linen garments. The garments must be suitable for drying in a tumble
dryer and suitable for ironing .
Express 20 3.5 Cold to 40°C Cotton garments that have hardly been worn or are only very lightly soiled.
Steam care – – Reducing the amount of creasing in damp, freshly washed and spun cotton
= Steam smoothing; = Short; = Stains, = Further options (see the operating instructions)
An explanation of the programmes at the Further programmes position can be found in the "Programme chart" in the operating instructions.
WMR 861 en - AU, NZ M.-Nr. 10 637 280/00
Cleaning and careProgrammeManager/Extra options Detergent
PROGRAMMEMANAGER/EXTRA OPTIONS/DETERGENT
CLEANING AND CARE
PROBLEM SOLVING GUIDE
Problem solving guide
ProgrammeManager
The ProgrammeManager option can
be used to customise the washing
programmes to suit your requirements.
Intensive
For hard-wearing laundry that is very heavily
soiled. Cleaning efficiency is increased
through more intense mechanical action
and the application of more heat energy.
ECO
This option reduces energy consumption
whilst maintaining cleaning efficiency. This
is achieved by increasing the wash duration
and at the same time reducing the wash
temperature selected.
Extra gentle
This option decreases mechanical action in
order to reduce creasing.
Extra quiet
This option reduces noise levels during the
programme. Use this if you want to wash
during quiet periods (for instance, when
children are sleeping). The machine will
activate the "Rinse hold" option and not
spin. The programme duration is longer.
AllergoWash
This option should be used where high
standards of hygiene are required. More
energy is used to lengthen temperature
holding times and more water is used to
increase rinsing efficiency. The items must
be suitable for drying in a tumble dryer
and suitable for ironing .
Extra options
Extra options are selected and deselected
via the relevant buttons and the display.
Steam smoothing
Steam is injected into the drum at the
end of the wash process. Reducing the
maximum load by 50% will give a better
result. For steam smoothing to work
properly there needs to be a certain amount
of residual moisture still present in the
laundry. The final spin speed is therefore
adjusted accordingly.
The garments must be suitable for drying in
a tumble dryer and suitable for ironing
.
Short
For light soiling with no visible staining.
The wash duration is reduced.
Stains
In order to clean stained laundry more
effectively, you can choose from a list
of various types of stains. The wash
programme will then adapt to the types of
stains selected. You can select a maximum
of three stains per wash cycle.
Further options
After pressing the button, more functions
will appear in the display. See "Extra
options" in the operating instructions for
more information.
Miele recommended detergents
Miele
UltraPhase
Programmes
Cottons
Minimum iron
Delicates
Woollens
Denim
Outerwear
1/2
–
–
–
Favourites
Mixed items
QuickPowerWash
Express 20
Steam care
= Recommended; – = Not recommended
= Sportswear; = Down Items; = Outerwear, = WoolCare; = SilkCare; = Fabric Softener;
= Proofing; = Booster
–
Dispensing fabric softener and
Miele
Cap
–
–
, , –
, – –
– – –
– –
depending on the basic programme set
– –
– – –
– –
– – –
Miele
Cap
Manual dispensing
liquid starch at the end of the
programme
You can dispense fabric softener either
by using automatic dispensing or via the
detergent dispenser compartment.
Automatic dispensing
One of the automatic dispensing containers
must be filled with fabric softener.
ĺ Touch the Dos sensor.
ĺ Activate the appropriate container.
Fabric softener will be dispensed in the last
rinse.
ĺ Add the fabric softener or liquid starch
to the compartment or insert the
appropriate capsule. Do not exceed the
maximum level mark.
It will be automatically dispensed in the
final rinse. At the end of the programme a
small amount of water remains in the fabric
softener compartment.
If starching frequently, thoroughly clean
the dispenser compartment, especially
the siphon, regularly.
Miele
Cap
The right amount to dispense will
depend on the following:
– The soiling level of the laundry.
Lightly soiled:
No visible dirt or stains. Possibly slight
body odour.
Normally soiled:
Visibly dirty and⁄or just a few slight stains.
Heavily soiled:
Soiling and⁄or stains clearly visible.
– The quantity of the laundry.
– Check with your local water supplier if
you do not know the hardness level in
your area.
TwinDos maintenance
ɉɉIf the system has not been used for
a long time (more than two months),
the detergent in the hoses can become
viscous.
The hoses could become blocked and
would then need to be cleaned by a
service technician.
Clean the TwinDos system every time you
change brand/type of liquid.
To clean the system, you either need
a "TwinDosCare" cleaning cartridge or
an empty TwinDos container. Both are
available from the Miele online shop (only
in selected countries).
The washing machine has a cleaning
programme for the TwinDos system.
Running the cleaning programme will clean
the hoses inside the washing machine.
Starting the maintenance programme
The maintenance programme is located in
the Settings menu under TwinDos.
ĺ Follow the instructions in the display
and refer to the relevant section in the
operating instructions.
The hoses will now be cleaned and the
TwinDos system can be used again. After
cleaning you can fill one or both containers
with new liquid detergent and/or fabric
softener.
Cleaning the compartment
Detergent residue can cause clogging.
ĺ Use a damp cloth to clean the
compartment interior when you change
the cartridge or container.
Cleaning the detergent dispenser
drawer
Washing at low temperatures and the use
of liquid detergent can lead to a build-up
of mould and bacteria in the detergent
dispenser drawer.
ĺ Clean the entire drawer at regular
intervals for hygiene reasons, even if you
are using the TwinDos system exclusively.
ĺ Pull out the
detergent
dispenser drawer
until a resistance
is felt.
ĺ Press down the release button and, at
the same time, pull the drawer right out of
the machine.
ĺ Clean the detergent dispenser drawer
with warm water.
Cleaning the siphon and the fabric
softener channel
ĺ Pull the siphon
out of the
compartment
and clean it
under warm
running water.
ĺ Clean the siphon tube in the same way.
ĺ Refit the siphon.
ĺ Clean the fabric
softener channel
using a brush
and warm water.
ɉɉLiquid starch can cause the siphon
to become clogged. Make sure that
you clean the siphon and siphon tube
particularly thoroughly after using liquid
starch a few times.
Cleaning the detergent dispenser
drawer housing
ĺ Use a bottle brush to remove detergent
residues and limescale from the jets
inside the detergent dispenser drawer
housing.
Cleaning the drum (Hygiene info)
Washing at low temperatures and/or
using liquid detergent can cause bacteria
and unpleasant odours to build up in the
washing machine. Use the Clean machine
programme to clean the machine. Run this
programme regularly or at the latest when
the Hygiene info: Start a programme with
a minimum temperature of 60°C message
appears in the display.
Message Possible cause and remedy
The display remains
dark, and the Start/
Stop button indicator
light does not come
on.
There is no power to the machine.
ĺ Check whether the mains plug is plugged in and switched
on.
ĺ Check whether the circuit breaker has tripped.
The washing machine has switched off automatically to save
energy.
ĺ Switch it back on with the button.
You are asked to enter
a code.
Access via a code has been activated.
ĺ Enter the code and confirm the entry. Deactivate the code
if you do not wish this message to appear in the display the
next time the machine is switched on.
Door lock
The door cannot be locked.
Call Miele.
The door is not closed properly. The door lock could not
engage.
ĺ Close the door again.
ĺ Start the programme again. If the fault message appears
again, contact Miele.
Drain fault
Clean the drain filter and
the drain pump. Check the
drain hose.
The water outlet is blocked or restricted. The drain hose has
been fixed too high.
ĺ Clean the drain filter and the drain pump.
ĺ Check whether the maximum delivery height of 1m been
exceeded.
Water inlet fault
Turn on the tap.
The water inlet is blocked or restricted.
ĺ Check whether the tap is turned on properly.
ĺ Check whether the inlet hose is kinked.
ĺ Check whether there is sufficient water pressure.
The filter in the water inlet is blocked.
ĺ Clean the filter (see the operating instructions).
Technical fault
Restart the appliance. If
the fault message appears
again, call Miele.
There is a fault.
ĺ Disconnect the washing machine from the mains electricity
supply, either by switching it off at the wall socket and
withdrawing the plug, or by disconnecting it at the circuit
breaker.
ĺ Wait at least 2 minutes before reconnecting the washing
machine to the mains electricity supply.
ĺ Then switch the washing machine on again.
ĺ Restart the programme.
If the fault message appears again, contact Miele.
The water protection
system has reacted.
Turn off the tap. Call Miele.
The water protection system has reacted. The washing
machine is switched off.
ĺ Turn off the tap.
ĺ Call Miele.
Door lock fault. Call
Miele.
The door lock has jammed.
ĺ Call Miele.
Message Possible cause and remedy
The “TwinDos Care”
for compartment und
has to be started
in “Settings, TwinDos,
Maintenance”. Follow the
instructions given in the
operating instructions.
Start a programme
and select “TwinDos”, or
carry out the “TwinDos
maintenance” in “Settings
- TwinDos”. Follow the
instructions given in the
operating instructions.
Intensive recirculation
system: Clean the filter and
jet nozzle or remove foreign
objects from the pump
housing.
TwinDos or automatic dispensing via compartment ⁄ has
not been used for a long time. It is possible that detergent has
dried inside the hoses.
ĺ Carry out the TwinDos maintenance programme immediately
as described in "Cleaning and care - TwinDos maintenance".
TwinDos or automatic dispensing via compartment ⁄ has
not been used for a long time.
ĺ Use TwinDos for one of your next loads.
ĺ Carry out the TwinDos maintenance programme as
described in "Cleaning and care - TwinDos maintenance".
The pumps are dirty.
ĺ Clean the pumps as described in "Problem solving guide -
Opening the door in the event of a blocked drain outlet and/
or power cut" in the operating instructions.
ĺ Start the programme again after cleaning.
The jet in the top of the door ring is blocked with fluff.
ĺ Remove the fluff with your finger. Do not use any sharp or
pointed tools to do this.
ĺ Start the programme again after cleaning.
If the fault message appears again, contact Miele. The washing
machine can still be used but with reduced functionality.
Hygiene info: Start a
programme with a minimum
temperature of 75°C.
A programme using a temperature above 60°C has not been
run for a long period of time.
ĺ In order to prevent bacteria and unpleasant odours building
up in the machine, run the Clean machine programme using
Miele dishwasher and washing machine cleaner or powder
detergent.
To switch off the fault messages: Switch the washing machine off with the button.
The messages will appear at the end of the programme and when the washing machine is
switched on and need to be confirmed with the OK sensor.
Quick Start Guide
Washing machine
These short instructions are not a substitute for the operating instructions supplied with
the appliance. Please read the operating instructions supplied with your washing machine
before using it for the first time and take note of the Warning and Safety instructions, as
well as the full descriptions on how to use your appliance.
en - AU, NZ M.-Nr. 10 637 280
Loading...