Operating and installation instructions
Ceramic hobs with induction
To avoid the risk of accidents or damage to the appliance it is essential
to read these instructions before it is installed and used for the first time.
M.-Nr. 07 798 980en-GB
2
Contents
Guide to the appliance .............................................5
After sales service, data plate, guarantee .............................77
4
Models
KM 6314
Guide to the appliance
aCooking zone with TwinBooster
bcd Cooking zones with Booster
eControl panel
5
Guide to the appliance
KM 6317 / KM 6318
ac Cooking zone with TwinBooster
bd Cooking zones with Booster
eControl panel
6
KM 6340 / KM 6342
Guide to the appliance
aCooking zone with TwinBooster
bcd Cooking zones with Booster
eControl panel
7
Guide to the appliance
h
Control panel
n
o
h
8
8
ab
Sensor controls
a For switching the hob on and off
b Numerical keypad
- For setting the power level
- For setting the time
c Safety lock
88
8
8
4012356789
i
m
g
f
k
l
e
j
d
c
d Booster/TwinBooster
e For selecting the cooking zone
f Stop and Go
g - For selecting the timer
- For switching between the timer functions
- For selecting the switch-off time (see "Switching off a cooking zone
automatically")
h Hour function
8
Guide to the appliance
Indicator lamps
i Safety lock
j Booster
Cooking zone displays
k
0= Cooking zone ready for use
^= Keeping warm function
1 to 9= Power levels
f= TwinBooster level 1
h= Booster/TwinBooster level 2
ß= No pan on cooking zone or pan unsuitable
(see "Induction")
#= Residual heat
A= Auto heat-up when the power level range has been extended
l Indicator lamp for Auto heat-up or extended power setting (see "Programming")
Timer display
m Indicator lamp for relevant zone, e.g. the rear right cooking zone
n
00 to 99 = Time in minutes
0.^ to 9^ = Time in hours
o Indicator lamp for half hours with a minute minder time of more than 99 minutes
9
Guide to the appliance
Cooking zones
Cooking
zone
y16 - 23Normal
w10 - 16Normal
x14-20/
z14 - 20Normal
* Pans of any diameter within the given range may be used.
** The wattage quoted may vary depending on the size and material of the pans
used.
Minimum to maximum
C in cm*
20x30
KM 6317 / KM 6318
Rating in watts for 230 V**
TwinBooster level 1
TwinBooster level 2
Booster
Normal
TwinBooster level 1
TwinBooster level 2
Normal
TwinBooster level 1
TwinBooster level 2
Booster
Total:7400
2300
3000
3700
1400
2200
1850
2500
3000
2300
3000
3700
1850
3000
10
Guide to the appliance
Cooking
zone
y16 - 23Normal
w10 - 16Normal
x14 - 20Normal
z14 - 20Normal
* Pans of any diameter within the given range may be used.
** The wattage quoted may vary depending on the size and material of the pans
used.
Minimum to maximum
C in cm*
KM 6314 / KM 6340 / KM 6342
Rating in watts for 230 V**
TwinBooster level 1
TwinBooster level 2
Booster
Booster
Booster
Total:7400
2300
3000
3700
1400
2200
1850
3000
1850
3000
Special feature
Hobs bearing the < symbol in the top left-hand corner are suitable for connecting
to the Miele|home system (see "Optional accessories").
11
Warning and Safety instructions
This hob complies with all relevant safety requirements.
Inappropriate use can, however, lead to personal injury and
damage to property.
To avoid the risk of accidents and damage to the appliance,
please read these instructions carefully before installation and
before using it for the first time. They contain important notes on
installation, safety, use and maintenance.
Miele cannot be held liable for damage caused by
non-compliance with these Warning and Safety instructions.
Keep these instructions in a safe place and ensure that new users
are familiar with the content. Pass them on to any future owner.
12
Warning and Safety instructions
Correct application
This hob is not designed for commercial use. It is intended for
~
use in domestic households and similar working and residential
environments.
The appliance is not intended for outdoor use.
~
It is intended for domestic use only to cook food and keep it
~
warm. Any other use is not supported by the manufacturer and
could be dangerous.
The appliance can only be used by people with reduced
~
physical, sensory or mental capabilities, or lack of experience and
knowledge, if they are supervised whilst using it, or have been
shown how to use it in a safe way and recognise and understand the
consequences of incorrect operation.
13
Warning and Safety instructions
Safety with children
Children under 8 years of age must be kept away from the
~
appliance unless they are constantly supervised.
Children 8 years and older may only use the appliance
~
unsupervised if they have been shown how to use it in a safe way
and can recognise and understand the consequences of incorrect
operation.
Children must not be allowed to clean the appliance
~
unsupervised.
This appliance is not a toy! To prevent the risk of injury, do not
~
allow children to play with the appliance or its controls.
The appliance gets hot when in use and remains hot for a while
~
after being switched off. Keep children well away from the appliance
until it has cooled down and there is no danger of burning.
Danger of suffocation. Packaging, e.g. plastic wrappings, must
~
be kept out of the reach of babies and children. Whilst playing,
children could become entangled in packaging, or pull it over their
head and suffocate.
Danger of burning.
~
Do not store anything which might arouse a child's interest in
storage areas above or behind the appliance. Otherwise they could
be tempted into climbing onto the appliance
Danger of burning or scalding.
~
Place pots and pans on the cooking zone in such a way that
children cannot pull them down and burn themselves.
Activate the system lock to ensure that children cannot switch on
~
the appliance inadvertently. Use the safety lock when the hob is in
use to prevent children from altering the settings selected.
14
Warning and Safety instructions
Technical safety
Unauthorised installation, maintenance and repairs can cause
~
considerable danger to users. Installation, maintenance and repair
work must only be carried out by a Miele authorised technician.
A damaged appliance can be dangerous. Check the appliance
~
for visible signs of damage. Do not use a damaged appliance.
The electrical safety of this appliance can only be guaranteed if
~
correctly earthed. It is most important that this basic safety
requirement is observed and regularly tested, and where there is
any doubt, the installation should be inspected by a qualified
electrician.
To avoid the risk of damage to the appliance, make sure that the
~
connection data (frequency and voltage) on the data plate
corresponds to the household supply, before connecting the
appliance to the mains supply.
Consult a qualified electrician if in any doubt.
Do not connect the appliance to the mains electrical supply by an
~
extension lead. These are a fire hazard and do not guarantee the
required safety of the appliance.
For safety reasons, this appliance may only be used after it has
~
been built in.
This appliance must not be used in a non-stationary location (e.g.
~
on a ship).
Do not open the casing of the appliance.
~
Tampering with electrical connections or components and
mechanical parts is highly dangerous to the user and can cause
operational faults.
15
Warning and Safety instructions
While the appliance is under guarantee, repairs should only be
~
undertaken by a service technician authorised by Miele. Otherwise
the guarantee is invalidated.
The manufacturer can only guarantee the safety of the appliance
~
when original Miele replacement parts are used. Faulty components
must only be replaced by genuine Miele original spare parts.
The hob is not intended for use with an external timer switch or a
~
remote control system.
The hob must be connected to the electrical supply by a qualified
~
electrician. If the connection cable is faulty, it must be replaced with
a special connection cable installed by a qualified electrician. See
"Electrical connection".
The appliance must be disconnected from the mains electricity
~
supply during installation, maintenance and repair work. Ensure that
power is not supplied to the appliance until after it has been
installed or until any maintenance or repair work has been carried
out.
If the hob is fitted with a communication module, in addition to
~
disconnecting the hob, this module must also be disconnected from
the mains electricity during installation and maintenance of the hob
as well as while any repair work is being carried out.
Danger of electric shock.
~
Do not use the hob if it is faulty, or if the ceramic surface is cracked,
chipped or damaged in any way. Switch it off immediately, and
disconnect it from the mains electricity supply.
In areas which may be subject to infestation by cockroaches or
~
other vermin, pay particular attention to keeping the appliance and
its surroundings in a clean condition at all times. Any damage which
may be caused by cockroaches or other vermin will not be covered
by the guarantee.
16
Warning and Safety instructions
Correct use
Oil and fat can overheat and catch fire. Do not leave the
~
appliance unattended when cooking with oil or fat.
If oil or fat does catch fire, do not attempt to put out the flames with
water. Disconnect the appliance from the mains and use a suitable
fire blanket, saucepan lid, damp towel or similar to smother the
flames.
Flames could set the grease filters of a cooker hood on fire. Do
~
not flambé under a cooker hood.
Spray canisters, aerosols and other inflammable substances can
~
ignite when heated. Therefore do not store such items or substances
in a drawer under the appliance. Cutlery inserts must be
heat-resistant.
Do not heat an empty pan.
~
Do not heat up unopened tins of food on the hob, as pressure will
~
build up in the tin, causing it to explode.
Do not cover the hob, e.g. with a hob cover, a cloth or protective
~
foil. The material could catch fire, shatter or melt if the appliance is
switched on by mistake or if residual heat is still present.
When using an electrical appliance, e.g. a hand-held food
~
blender, near the appliance, ensure that the cable of the electrical
appliance cannot come into contact with the hot appliance. The
insulation on the cable could become damaged.
If the appliance is installed behind a kitchen furniture door, it may
~
only be used with the furniture door open. Do not close the door
whilst the hob in use or whilst there is any residual heat present.
The appliance gets hot when in use and remains hot for a while
~
after being switched off. There is a danger of burning until the
residual heat indicators go out.
17
Warning and Safety instructions
You could burn yourself on the hot hob. Protect your hands with
~
heat-resistant pot holders or gloves when handling hot pots and
pans. Do not let them get wet or damp, as this causes heat to
transfer through the material more quickly with the risk of scalding or
burning yourself.
When the appliance is switched on either deliberately or by
~
mistake, or when there is residual heat present, there is the risk of
any metal items left on the hob heating up, with the danger of
burning.
Depending on the material, other items left on the hob could also
melt or catch fire.
Damp pan lids might adhere to the ceramic surface and be difficult
to dislodge.
Do not use the appliance as a resting place.
Switch the cooking zones off after use.
Do not allow solid or liquid sugar, or pieces of plastic or
~
aluminium foil to get onto the cooking zones when they are hot, as
they can damage the ceramic surface when it cools down. If this
should occur, switch off the appliance and scrape off all the sugar,
plastic or aluminium residues whilst still hot, using a shielded
scraper blade. Wear oven gloves.
Allow the cooking zones to cool down and then clean them with a
suitable ceramic hob cleaning agent.
Pans which boil dry can cause damage to the ceramic glass. Do
~
not leave the appliance unattended whilst it is being used.
Do not use pots or pans on the hob with bases with pronounced
~
edges or ridges. These could scratch or scour the ceramic glass
surface permanently. Only use pots and pans with smooth bases.
Lift pans into position on the hob. Sliding them into place can
~
cause scuffs and scratches.
18
Warning and Safety instructions
Grains of salt, sugar and sand (e.g. from cleaning vegetables)
~
can cause scratches if they get under pan bases. Make sure that
the ceramic surface is clean before placing pans on it.
Even a light object could cause damage in certain
~
circumstances. Do not drop anything on the ceramic surface.
Do not place hot pans on the sensors and display as this could
~
cause damage to the electronics underneath. Do not place hot pans
on the area around the display.
Induction heating works extremely quickly and so the base of the
~
pan could heat up to the temperature at which oil or fat self-ignites
within a very short time. Do not leave the appliance unattended
whilst it is being used.
Heat oil or fat for a maximum of one minute. Do not use the
~
Booster function to heat oil or fat.
For people fitted with a heart pacemaker:
~
Please note that the area immediately surrounding the hob is
electromagnetically charged. It is unlikely to affect a pacemaker.
However, if in any doubt, consult the manufacturer of the pacemaker
or your doctor.
To prevent damage to items which are susceptible to magnetic
~
fields, e.g. credit cards, digital storage devices, pocket calculators,
etc, do not leave them in the immediate vicinity of the hob.
Metal utensils stored in a drawer under the hob can become hot if
~
the appliance is used intensively for a long time. Do not store any
metal items or utensils in a drawer under the hob.
19
Warning and Safety instructions
This hob is fitted with a cooling fan. If a drawer is fitted directly
~
underneath the hob, ensure that there is sufficient space between
the drawer and its contents and the underside of the appliance in
order to ensure sufficient ventilation of the hob.
Do not store pointed or small items or paper in the drawer. They
could get in through the ventilation slots or be sucked into the
housing by the fan and damage the fan or impair cooling.
Do not use two pans on a cooking zone, extended zone or
~
PowerFlex zone at the same time.
Cleaning and care
Do not use a steam cleaning appliance to clean this appliance.
~
The steam could reach electrical components and cause a short
circuit.
If the hob is built in over a pyrolitic oven or cooker, the hob
~
should not be used whilst the pyrolitic process is being carried out,
as this could trigger the overheating protection mechanism on the
hob (see relevant section).
20
Caring for the environment
Disposal of the packing
material
The packaging is designed to protect
the appliance from damage during
transportation. The packaging materials
used are selected from materials which
are environmentally friendly for disposal
and should be recycled.
Recycling the packaging reduces the
use of raw materials in the
manufacturing process and also
reduces the amount of waste in landfill
sites.
Disposing of your old
appliance
Electrical and electronic appliances
often contain valuable materials. They
also contain materials which, if handled
or disposed of incorrectly, could be
potentially hazardous to human health
and to the environment. They are,
however, essential for the correct
functioning of your appliance. Please
do not therefore dispose of it with your
household waste.
Please dispose of it at your local
community waste collection/recycling
centre or contact your dealer for
advice. Ensure that it presents no
danger to children while being stored
for disposal.
21
Before using for the first time
Please stick the extra data plate for the appliance supplied
with this documentation in the space provided in the "After
sales service, data plate" section of this booklet.
Cleaning for the first time
Remove any protective wrapping and adhesive labels.
^
Before using for the first time, clean the appliance with a
^
damp cloth only and then wipe dry.
Before using for the first time
On hobs with bevelled glass edges, a small gap may be
visible between the hob and the worktop during the first
few days after installation. This gap will reduce with time as
the appliance is used and will not affect the electrical
safety of your appliance.
When the appliance is used for the first time, it may give off a
slight smell and some vapours. This smell will be less
noticeable with each subsequent use before dissipating
completely.
22
The smell and any vapours given off do not indicate a faulty
connection or appliance and they are not hazardous to
health.
Please note that the heating up time on induction hobs is
very much shorter than on conventional hobs.
The induction principle
An induction coil is located under each cooking zone. When
a cooking zone is switched on, this coil creates a magnetic
field which impacts directly on the base of the pan and heats
it up. The cooking zone itself is heated up indirectly by the
heat given off by the pan.
An induction cooking zone only works when a ferromagnetic
pan is placed on it (see "Pans").
Induction automatically recognises the size of the pan, i.e.
heat is only generated in the area covered by the base of the
pan.
The cooking zone will not work:
– if it is switched on without a pan in place, or if the pan is
unsuitable (non-magnetic base).
– if the diameter of the base of the pan is too small.
– if the pan is taken off the cooking zone when it is switched
on.
If this happens, ß will flash in the relevent cooking zone
display alternating with the power setting selected.
Induction
If a suitable pan is placed on the cooking zone within
3 minutes, the ß will go out and you can continue as normal.
If no pan or an unsuitable pan is placed on the cooking zone,
the cooking zone and the hob will switch off automatically
after 3 minutes.
Take particular care never to place cutlery or other metal
objects on the hob. When the appliance is switched on
either deliberately or by mistake, or when there is residual
heat present, there is the risk of metal items heating up
with the danger of burning.
Switch the cooking zones off after use.
23
Induction
Noises
When using an induction cooking zone, the following noises
can occur in the pan, depending on what it is made of and
how it has been constructed.
On the higher power settings, it might buzz. This will
–
decrease or cease altogether when the power setting is
reduced.
If the pan base is made of layers of different materials (e.g.
–
in a sandwiched base), it might emit a cracking sound.
Whistling might occur if linked zones (see "Booster
–
function") are being used at the same time, and the pans
also have bases made of layers of different materials.
– You might hear a clicking sound from the electronic
switches, especially on lower settings.
The appliance has a cooling fan to help extend the life of the
electronics. When the hob is being used intensively, this will
come on and you will hear a whirring sound. The fan may
continue to run after the appliance has been switched off.
24
Pans
Induction
Suitable pans include:
stainless steel pans with a magnetic base
–
enamelled steel pans
–
cast iron pans
–
Unsuitable pans:
stainless steel pans without a magnetic base
–
aluminium and copper pans
–
glass, ceramic or earthenware pots and pans
–
To test whether a pot or pan is suitable for use on an
induction hob, hold a magnet to the base of the pan. If the
magnet sticks, the pan is suitable.
Please be aware that the properties of the pan base can
affect the eveness with which food heats up in the pan.
To make optimum use of the cooking zones, choose pans
with diameters larger than the innermost markings but smaller
than the outermost markings. If the diameter of the pan is
smaller than the innermost marking, the induction heating will
not work. The zone will behave as if it had no pan on it.
Please note that the maximum diameter quoted by
manufacturers often refers to the diameter of the top rim of
the pot or pan. The diameter of the base (generally smaller) is
more important.
Make sure that pans are placed centrally on the cooking
zone.
If a pan is placed only partially on a zone, there is a risk
that the handle could get very hot.
25
Operation
How the hob is operated
The hob is equipped with electronic sensor controls which
react to finger contact.
To operate the hob, touch the relevant sensor. Each time you
touch a sensor, an audible tone sounds.
In order to set or alter a power level or the time, the cooking
zones and the timer must be "active".
To activate a cooking zone or the timer, touch the sensor for
selecting the relevant cooking zone or the timer. After you
have touched the sensor, the relevant cooking zone or timer
display will start to flash. The cooking zone or the timer is
"active" whilst the display is flashing and you can set a power
level or time.
Exception:
If only one of the cooking zones is in operation, you can alter
the power level without activating the cooking zone.
Take care to keep the control panel clean and do not
place anything on top of it. The sensors may fail to react or
they could mistake the article or any dirt for a fingertip
contact, thereby activating a function or even causing the
hob to switch off automatically (see "Safety switch-off".)
26
Never place hot pans on the sensors. The electronic unit
underneath could get damaged.
Switching on
The hob must be switched on before any of the zones can be
used.
Do not leave the appliance unattended whilst it is being
used.
To switch the hob on
Touch the s sensor.
^
0 will appear in each of the cooking zone displays. If no
further entry is made, the hob will switch itself off after a few
seconds for safety reasons.
Switching on a cooking zone, setting a power level
^ Touch the sensor for selecting the cooking zone you want.
A 0 will flash in the cooking zone display.
^ Set the power level you want by touching the relevant
number on the numerical keypad.
To set one of the intermediate settings you need to touch
the area between the numbers (see "Power level range").
Operation
The power level selected flashes in the display for a few
seconds to start with and then lights up constantly.
Altering the power level
^
Touch the sensor for selecting the cooking zone you want.
The power level will flash in the cooking zone display.
^
Set the power level you want by touching the relevant
number on the numerical keypad.
If only one of the cooking zones is in operation, you can
alter the power level without activating the cooking zone.
27
Operation
Power level range
The appliance is delivered with 9 power levels programmed in. If you wish to
fine-tune a setting, you can extend the power level range (see "Programming").
The intermediate setting will be represented by an illuminated dot next to the
number.
Settings
Standard
factory settings
(9 power levels)
Keeping warmhh
Melting butter
Dissolving gelatine
Making milk puddings22 - 2.
Warming small quantities of liquid
Cooking rice
Defrosting frozen vegetables32. - 3
Making porridge32. - 3.
Warming liquid and semi-solid foods
Making omelettes and lightly frying eggs
Steaming fruit
Cooking dumplings44 - 5.
Steaming vegetables and fish55
Defrosting and heating frozen food55 - 5.
Bringing large quantities of food to the boil, e.g. casseroles
Thickening custard and sauces, e.g. hollandaise
Gently frying eggs (without overheating the fat)65. - 6.
Gently braising meat, fish and sausages (without overheating
the fat)
Frying pancakes etc.76. -7
Cooking stew88 - 8.
Boiling large quantities of water
Bringing to the boil
1-21-2.
33-3.
44-4.
65.-6
76.-7.
99
Extended
settings
(17 power levels)
These settings should only be taken as a guide.
The power of the induction coils will vary depending on the size and material of the pan. For this
reason it is possible that the settings will need to be adjusted slightly to suit your pans. As you use the
hob, you will get to know which settings suit your pans best.
28
Auto heat-up
When Auto heat-up has been activated, the cooking zone
switches on automatically at the highest power setting and
then switches to the continued cooking setting selected. The
heat-up time depends on which continued cooking setting
has been chosen (see chart).
To activate Auto heat-up
Touch the sensor for selecting the cooking zone you want.
^
The cooking zone display will flash.
Touch the number for the continued cooking setting you
^
want until an audible tone sounds and the indicator lamp to
the right of the continued cooking setting lights up.
The indicator lamp to the right of the continued cooking
setting will go out at the end of the auto heat-up time.
In the extended range of power settings (see
"Programming"), A flashes alternately with the continued
cooking setting during the heat-up time.
Altering the continued cooking setting will deactivate auto
heat-up.
Operation
To deactivate Auto heat-up
You can switch off Auto heat-up before the Auto heat-up time
has finished.
^
Touch the sensor for selecting the cooking zone you want.
The cooking zone display will flash.
Touch the continued cooking setting which has been
selected until the indicator lamp or A goes out; or set a
different power level.
29
Operation
Continued
cooking setting*
10:15
1.0:15
20:15
2.0:15
30:25
3.0:25
40:50
4.0:50
52:00
5.5:50
65:50
6.2:50
72:50
7.2:50
82:50
Heat-up time
in minutes and seconds (approx.)
30
8.2:50
9-
* The continued cooking settings with a dot after the number
are only available if the power level range has been
extended (see "Programming").
Booster function
Operation
The cooking zones are equipped with a Booster or
TwinBooster (see "Guide to the appliance").
When activated, the power is boosted for 15 minutes so that
large quantities can be heated quickly, e.g. when boiling
water for cooking pasta.
The Booster function can only be used on two cooking zones
at the same time, one on the left and one on the right.
If the Booster function is switched on when
no setting has been selected, the cooking zone will revert
–
automatically to setting 9 at the end of the Booster time or
if the Booster function is switched off before this.
– a setting has been selected, the cooking zone will revert
automatically to the setting selected at the end of the
Booster time or if the Booster function is switched off
before this.
Taking a pan off the zone whilst the Booster is in operation
interrupts the Booster function. It will resume if a pan is
placed back on the zone within 3 minutes.
The extra boost of energy is only available by taking a
proportion of energy away from another cooking zone. For
this reason, the cooking zones are networked in pairs.
Example:
When selecting the Booster/TwinBooster level 1 for a zone,
the following happens within the pairs:
–
If Auto heat-up is activated on the other zone within the
pair, this will be switched off.
–
If the other zone within the pair is set at power level 9, the
power level on that zone will be reduced.
If TwinBooster level 2 is selected, the other zone within the
networked pair will be switched off.
31
Operation
To switch on the Booster
Touch the sensor for selecting the cooking zone you want.
^
Select a power level if you wish.
^
Touch the B I/II sensor.
^
The indicator lamp for the Booster lights up, and h starts to
flash in the cooking zone display.
After a few seconds, h will light up constantly and the
indicator lamp will go out.
To switch on the TwinBooster
Level 1
^ Touch the sensor for selecting the cooking zone you want.
^ Select a power level if you wish.
^ Touch the B I/II sensor.
The indicator lamp for the Booster lights up, and f starts to
flash in the cooking zone display. After a few seconds, f will
light up constantly and the indicator lamp will go out.
Level 2
^ Touch the sensor for selecting the cooking zone you want.
^
Select a power level if you wish.
^
Touch the B I/II sensor twice.
The indicator lamp for the Booster lights up, and h starts to
flash in the cooking zone display. After a few seconds, h will
light up constantly and the indicator lamp will go out.
To switch off the Booster/TwinBooster
^
Touch the sensor for selecting the cooking zone you want.
^
Touch the B I/II sensor until the indicator lamp for the
Booster goes out and the cooking zone setting shows in
the display.
or
^
Touch the sensor for selecting the cooking zone you want.
^
Select a different power level.
32
Keeping warm function
Each cooking zone has a keeping warm function ("h"). The "h"
function is in between the "0" setting and the "1" setting.
If the keeping warm function has been activated, the cooking
zone will switch off automatically after a maximum of 2 hours.
This function is for keeping food that has just been cooked
warm, i.e. food that is still hot. It is not for reheating food
that has gone cold.
To set the keeping warm function
Touch the sensor for selecting the cooking zone you want.
^
Touch the area inbetween the "0" setting and the "1"setting.
^
"h" will light up in the display.
Useful tips
Only use pans for keeping food warm. Cover the pan with a
lid.
You do not have to stir food while it is being kept warm.
Operation
Nutrients are lost when food is cooked, and this will continue
when food is kept warm. The longer food is kept warm for, the
greater the loss of nutrients. Try to ensure that food is kept
warm for as short a time as possible.
33
Operation
Switching off and residual heat indicators
Switching off a cooking zone
Touch the sensor for selecting the cooking zone you want
^
twice.
A 0 will flash in the cooking zone display for a few seconds. If
the cooking zone is still hot, the residual heat indicator will
then appear in the display.
Switching off the hob
Touch the s sensor.
^
This switches off all cooking zones. The residual heat
indicator will appear in the display of any cooking zone which
is still hot.
Residual heat indicators
The lines of the residual heat indicator go out one after
another as the cooking zone cools down. The last horizontal
line only goes out when the cooking zone is safe to touch.
Do not touch or place any heat-sensitive objects on the
cooking zones while the residual heat indicators are on.
Danger of burning.
34
Tips on saving energy
Use a pan lid whenever possible to minimise heat loss.
–
uncoveredcovered
Select a smaller pan when cooking small quantities. A
–
smaller pan uses less energy than a larger pan with very
little in it.
Cook with as little water as possible.
–
– Once food has come to the boil or the oil in the pan is hot
enough for frying, reduce the heat to a lower setting.
– Cooking times are greatly reduced when using a pressure
cooker.
35
Timer
h
The hob must be switched on to use the timer.
The timer can be used for two different functions:
to set the minute minder
–
to set a cooking zone to switch off automatically.
–
You can select a time from 1 minute (01) to 9 hours (9^).
A time of up to 99 minutes is set and displayed in minutes.
Example:
To set a time of more than 99 minutes, the timer must be set
to hours (h). The time is then set in half hour stages. The half
hour is indicated by a dot after the number.
Example (2 h 30 min):
When the set time has elapsed 00 will appear in the timer
display. At the same time an audible tone will sound for a few
seconds.
36
Minute minder
h
h
h
To set the minute minder time
Minutes
Example: You want to set 15 minutes.
Switch the hob on.
^
Touch the m sensor.
^
00 will appear in the timer display. The 0 on the right will
flash.
Enter the tens first and then the units.
^ Touch the number on the numerical keypad which
corresponds to the tens position (1 in this case).
Timer
The timer display will change and 1 will start flashing.
^
Touch the number on the numerical keypad which
corresponds to the units position (5 in this case).
The timer display will change. The 1 moves to the left and 5
appears on the right.
The minute minder time will begin to count down.
37
Timer
h
h
h
Hours
Whole hours are set by touching the relevant number on the
numerical keypad.
Half hours are set by touching the area between the relevant
two numbers.
Example: You want to set 2 hours 30 minutes.
Switch the hob on.
^
Touch the m sensor.
^
00 will appear in the timer display. The 0 on the right will
flash.
^ Touch the h sensor, to change the display to show the
hours.
^
Touch the area between the numbers 2 and 3 on the
numerical keypad.
The timer display will light up constantly after a few seconds.
The minute minder time will begin to count down.
38
To change the minute minder time
Touch the m sensor.
^
Set the time you want, as described above.
^
To delete the minute minder time
Touch the m sensor until 00 appears in the timer display.
^
Timer
39
Timer
To switch a cooking zone off automatically
You can set a time at the end of which a cooking zone will
switch off automatically.
All the cooking zones can be programmed at the same time.
If the time programmed is longer than the maximum
operational time allowed, the cooking zone will switch off
after the maximum time allowed (see "Safety switch-off").
Select a power level for the cooking zone you want.
^
Touch the m sensor repeatedly until the indicator lamp for
^
this cooking zone flashes.
If more than one cooking zone is switched on, the indicator
lamps will flash clockwise beginning with the front left zone.
^ Set the time you want.
The time set will then count down in minutes. The time
remaining will be shown in the timer display. You can change
this at any time.
If you want to set another cooking zone to switch off
automatically, follow the same steps as described above.
40
If more than one switch-off time is programmed, the shortest
time remaining will show in the display, and the
corresponding indicator lamp will flash. All the other indicator
lamps will light up constantly. If you want to check on the time
remaining for another zone, touch the m sensor repeatedly
until the indicator lamp for the zone you want flashes.
To use both timer functions at the same time
The minute minder and automatic switch-off functions can be
used at the same time.
If you have programmed in one or more switch-off times, and
would like to use the minute minder as well:
Touch the m sensor repeatedly until the indicator lamps for
the cooking zones you have programmed light up constantly
and 00 appears in the timer display.
If you are using the minute minder, and would like to
programme in one or more switch-off times as well:
Touch the m sensor repeatedly until the indicator lamp for
the cooking zone you want flashes.
Shortly after the last entry, the timer display switches to the
function with the shortest remaining time.
If you want to show the times remaining which are counting
down in the background, touch the m repeatedly until
- the indicator lamp for the cooking zone you want flashes
(automatic switch-off).
- only the timer display is flashing (minute minder).
Starting with the shortest time remaining which is shown in
the display, all cooking zones which are switched on and the
minute minder are selected clockwise.
Timer
41
Safety features
Safety lock / System lock
Keep children away from the hob for their own safety.
Your appliance is equipped with a safety lock to prevent the
hob and the cooking zones being switched on or any settings
being altered.
The safety lock is set with the hob switched on. When
activated:
The cooking zone power levels and the timer settings
–
cannot be changed.
The cooking zones, the hob and the timer can be switched
–
off, but once switched off cannot be switched on again.
The system lock is set with the hob switched off. When
activated, the hob cannot be switched on and the timer
cannot be used.
The default setting for activating the system lock is manual.
The system lock can also be set for manual and automatic
activation, in which case it will be activated automatically five
minutes after the hob has been switched off, unless you set it
manually (see "Programming").
42
If an unavailable sensor is touched whilst the safety lock or
system lock is activated, the safety lock indicator will light up
and LC will appear in the timer display for a few seconds.
The safety lock is programmed at the factory for
three-finger operation. You can alter the setting from
three-finger to one-finger operation (see "Programming").
If there is an interruption to the power supply, the safety
lock and the system lock will be deactivated.
Activating
Deactivating
Safety features
Three-finger operation (standard default setting)
Touch the $ sensor and the sensors for selecting both
^
right-hand cooking zones at the same time until the safety
lock indicator lights up and LC appears in the timer display.
The safety lock indicator and LC will go out after a short while.
One-finger operation
Touch the $ sensor until the safety lock indicator lights up
^
and LC appears in the timer display.
The safety lock indicator and LC will go out after a short while.
Three-finger operation (standard default setting)
^ Touch the $ sensor and the sensors for selecting both
right-hand cooking zones at the same time until the safety
lock indicator and LC in the timer display go out.
One-finger operation
^
Touch the $ sensor until the safety lock indicator and LC in
the timer display go out.
43
Safety features
Stop and Go
Your appliance has a Stop and Go feature which, when
activated, reduces the power of all cooking zones in use to
power level 1. When Stop and Go is activated, the cooking
zone power levels and the setting of the timer cannot be
altered and the hob can only be switched off.
When Stop and Go is deactivated, the cooking zones resume
at the power level which was last set.
If Stop and Go is not deactivated, the hob switches off after 1
hour.
When Stop and Go is activated
- the countdown of a time programmed in for automatic
- the minute minder will continue without interruption.
Activating
^ Touch the sensor.
The power of the cooking zones in use will be reduced to
power level 1.
switch-off will be interrupted. When deactivated, the time
will continue to run.
Deactivating
44
^
Touch the sensor.
The cooking zones will now run at the level that was
previously set.
Safety switch-off
Safety switch-off with an over-long cooking time
If one of the cooking zones is heated for an unusually long
period of time (see chart) and the power level is not altered,
the hob will switch itself off automatically and the relevant
residual heat indicator will light up.
To use the cooking zone again, switch it back on in the usual
way.
Power level*Maximum operating time in hours
h2
1/1.10
2/2.5
3/3.5
4/4.4
5/5.3
6/6.2
Safety features
7/7.2
8/8.2
91
* The power levels with a dot after the number are only
available if the power level range has been extended (see
"Programming").
Safety switch-off if the sensors are covered
Your hob will switch off automatically if one or several of the
sensors remain covered for more than about 10 seconds, for
example by finger contact, food boiling over, or by an object
such as an oven glove or a tea towel.
F will appear in the timer display
^
Clean the control panel or remove the obstruction.
F will disappear. You can now use the hob again.
45
Safety features
Overheating protection
All the induction coils and the cooling elements for the
electronics are fitted with an overheating protection
mechanism. Before the induction coils or cooling elements
get too hot, the overheating protection mechanism cuts in in
one of the following ways:
Induction coils
If the booster function is being used, this will be switched
–
off.
The power level will be reduced.
–
The cooking zone will switch off automatically.
–
"FE" will flash in the timer display alternately with "44".
You will be able to use the cooking zones again as usual
when the fault code has gone out.
Cooling elements
– If the booster function is being used, this will be switched
off.
46
– The power level will be reduced.
– The cooking zones will switch off automatically.
The affected cooking zones can only be used again as usual
once the cooling element has cooled down to a safe level.
The overheating mechanism can be triggered by:
–
Heating up an empty pan.
–
Fat or oil being heated up on a high power level.
–
Insufficient ventilation to the underside of the appliance.
–
A hot cooking zone being switched on after a power cut.
If the overheating protection mechanism triggers again,
contact the Service department.
Cleaning and care
For Miele branded cleaning and conditioning products see
"Optional accessories".
Do not use a steam cleaning appliance to clean this
,
appliance. The steam could reach electrical components
and cause a short circuit.
The appliance should be cleaned after each use. Let it cool
down to room temperature before cleaning.
To avoid water marks and limescale deposits, use a soft cloth
to dry surfaces that have been cleaned with water.
To avoid damaging the surface of your appliance, do not
use:
– abrasive cleaning agents, e.g. powder cleaners and cream
cleaners,
– solvent-based cleaning agents,
–
dishwasher cleaner,
–
grill and oven cleaners,
–
glass cleaning agents,
–
hard, abrasive brushes or sponges, e.g. pot scourers,
brushes or sponges which have been previously used with
abrasive cleaning agents,
–
melamine eraser blocks,
–
sharp, pointed objects which could damage the seal
between the ceramic surface and the surrounding frame,
and between the frame and the worktop.
47
Cleaning and care
Do not use washing-up liquid to clean the ceramic surface.
Washing-up liquid will not remove all soiling and deposits.
It will form an invisible coating which will cause permanent
discolouration of the ceramic surface.
Clean the hob regularly with a suitable ceramic hob
cleaner.
Wipe all coarse soiling off using a damp cloth. Stubborn
soiling may need to be removed with a shielded scraper
blade.
Then clean the hob with Miele ceramic and stainless steel
hob cleaner (see "Optional accessories") applied with kitchen
paper or a clean cloth. Do not apply cleaner whilst the hob is
still hot, as this could result in marking. Please follow the
manufacturer's instructions.
Finally, wipe the hob with a damp cloth, then polish with a
soft, dry cloth. Ensure that all cleaner residues are removed.
Residues can burn onto the hob the next time it is used, and
cause damage to the ceramic surface.
Spots caused by limescale, water and aluminium residues
(spots with a metallic appearance) can be removed using
Miele's ceramic and stainless steel hob cleaner.
48
Should any sugar, plastic or aluminium foil spill or fall onto
a hot cooking zone while it is in use, first switch off the
appliance. Then carefully scrape off all the sugar, plastic or
aluminium residues from the hob whilst they are still hot,
using a shielded scraper blade. Take care not to burn
yourself.
Allow the appliance to cool down, and then clean as
described above.
You can change the default settings of the programme
options (see chart). Several settings can be altered in
succession.
After selecting programming mode, P (Programme) and S
(Status) will appear in the timer display. On hobs with 3
cooking zones, an additional indicator will appear at the rear
left.
The programme is shown in the cooking zone displays at the
front left and rear left. Example:
Programme 03 = front left 0, rear left 3
Programme 14 = front left 4, rear left 1
The status is shown in the front right cooking zone display.
Once you have left the programming mode, the hob will be
reset automatically. This is completed when an indicator
above the s sensor lights up briefly.
Do not switch the hob on again until the reset process is
completed.
To select programming mode
Programming
^ With the hob switched off, touch the s and $ sensors at
To set the programme
^
^
To set the status
^
the same time until the safety lock indicator light flashes.
To set the units position first touch the sensor for selecting
the rear left cooking zone and then touch the relevant
number on the numerical keypad.
To set the tens position first touch the sensor for selecting
the front left cooking zone and then touch the relevant
number on the numerical keypad.
Touch the sensor for selecting the front right cooking zone
and then touch the relevant number on the numerical
keypad.
49
Programming
To save settings
To not save settings
Touch the s sensor until all the displays go out.
^
Touch the $ sensor until all the displays go out.
^
50
Programme*Status**Setting
Programming
P00Demonstration
mode and
factory default
settings
P01Stop and GoS0Off
P02Power level
range
P03Induction
warning tone
when there is no
pan or the pan
is unsuitable
P04Keypad tone
when a sensor
is touched
S0Demonstration mode on
(after the hob is switched on, "dE" will
appear in the timer display for a few
seconds).
S1Demonstration mode off
S9Factory default settings reinstated
S1On
S09 power levels
(1, 2, 3 ... to 9)
S117 power levels
(1, 1., 2, 2., 3 ... to 9)
If the Auto heat-up setting is selected, an
A will flash alternately with the continued
cooking setting in the display.
S0Off
S1Quiet
S2Medium
S3Loud
S0Off
S1Quiet
S2Medium
S3Loud
P05Timer audible
tone
*Programmes/ Status numbers not shown here have no allocation.
** The factory default settings are shown in bold.
S0Off
S1Quiet for 10 seconds
S2Medium for 10 seconds
S3Loud for 10 seconds
51
Programming
Programme*Status** Setting
P06Safety lockS0One-finger locking using $
S1 Three-finger locking by touching
$ and the sensors for selecting
the right-hand cooking zones at
the same time
P07System lockS0 Manual activation of the system
lock only
S1Manual and automatic activation
of the System lock
P08Auto heat-upS0Off
S1 On
P10Miele|home
- only on
communication-enabled
appliances fitted with a
communication module.
P15Audible tone if a sensor
is covered
P16Sensor reaction speedS0Slow
* Programmes / Status numbers not shown here have no allocation.
** The factory default settings are shown in bold.
S0 Feature not fitted
S1Signed off
S2Signed on
S0 Off
S1 On
S1 Normal
S2Rapid
52
Problem solving guide
With the help of the following notes, minor faults in the performance of the
appliance, some of which may result from incorrect operation can be put right
without contacting the Service Department.
Installation work and repairs to electrical appliances must only be carried out
by a suitably qualified and competent person in strict accordance with current
local and national safety regulations. Do not attempt to open the casing of the
appliance. Repairs and other work by unqualified persons could be dangerous
and Miele cannot be held liable for unauthorised work.
ProblemPossible causeRemedy
The hob or cooking
zones cannot be
switched on.
The mains fuse has tripped. Reset the trip switch in the
mains fuse box (minimum
fuse rating - see data
plate).
There may be a technical
fault.
Disconnect the appliance
from the electricity supply
for approx. 1 minute. To do
this:
– switch off at the isolator,
or
– disconnect the mains
fuse.
Reset the trip switch in the
mains fuse box, and switch
the appliance back on. If it
still will not switch on,
contact a qualified
electrician or the Miele Ser
vice Department.
-
53
Problem solving guide
ProblemPossible causeRemedy
A smell and vapours
are given off when a
new appliance is
being used.
The ß symbol flashes
alternately with the
power setting
selected in one of the
cooking zones.
After the hob is
switched on "LC"
appears in the timer
display for a few
seconds.
After the hob is
switched on "dE"
appears in the timer
display for a few
seconds.
The cooking zones do
not heat up.
A cooking zone or the
whole hob switches
off automatically.
There is no pan on the
cooking zone, or the pan is
unsuitable.
The system lock is
activated.
The appliance is in
demonstration mode.
A cooking zone has been
in use for too long.
The smell and vapours will
be less noticeable with
each subsequent use
before dissipating
completely.
Use a suitable pan (see
"Pans").
Deactivate the system lock
(see "Safety lock / System
lock").
Deactivate demonstration
mode (see
"Programming").
You can use the cooking
zone again by switching it
back on (see "Safety
switch-off").
The Booster has
deactivated early
automatically.
The cooking zone is
not working in the
usual way at the
power level set.
54
The overheating protection
mechanism has triggered.
The overheating protection
mechanism has triggered.
See "Overheating
protection".
See "Overheating
protection".
Problem solving guide
ProblemPossible causeRemedy
Power level 9 is
automatically reduced
if you select power
level 9 on two linked
cooking zones or
extended zones at the
same time.
The hob switches off
while it is in use and an
F flashes in the timer
display.
The food in the pan
hardly heats up or does
not heat up at all when
the Auto heat-up
function is switched
on.
The cooling fan
continues to run after
the appliance has been
switched off.
Operating both zones
at power level 9 would
exceed the permitted
maximum power level
for the two zones.
One or more of the
sensors have been
covered, e.g. by finger
contact, food boiling
over or by an object
such as an oven glove.
There is too much food
in the pan.
The pan is not
conducting heat
properly.
The fan will continue
running until the
appliance has cooled
down. It will then
switch itself off
automatically.
Clean the control panel or
remove the obstruction (see
"Safety switch-off").
Start cooking at the highest
power level and then turn
down to a lower one
manually later on.
55
Problem solving guide
ProblemPossible causeRemedy
The sensors are
over-sensitive or do
not react at all.
FE flashes alternately
with numbers in the
timer display.
FE 44The overheating
FE 47The fan is either
FE 48
The sensitivity level of
the sensors has
changed.
protection
mechanism has
triggered.
blocked or faulty.
Make sure that there is no direct
light (from the sun or from an
artificial source) falling onto the
hob and that the surrounding
area is not too dark.
Make sure that there is nothing
covering the sensors or the hob.
Take any pans off the hob and
wipe away any food deposits.
Interrupt the power supply to the
hob for approx. 1 minute.
If this does not solve the
problem, please call the Miele
Service department.
See "Overheating protection".
Make sure it has not been
blocked by something like a
fork. Remove the cause of the
blockage. If the fault message
appears again, call the Miele
Service Department.
Other fault messages
FE..
56
There is an electronic
fault.
Interrupt the power supply to the
hob for approx. 1 minute.
If the problem persists after
reconnecting the appliance to
the power supply, please
contact the Miele Service
department.
Pans
Optional accessories
Miele offer a comprehensive range of useful accessories as
well as cleaning and conditioning products for your Miele
appliances.
These can be ordered online at:
or from Miele (see back of manual for contact details).
Miele offer a wide range of pans which are perfect for Miele
hobs. Please refer to the Miele website for more details on
individual products.
Pans in various sizes
Frying pan with lid
Non-stick pans
Wok
Gourmet oven dish
Cleaning products
Ceramic and stainless steel hob cleaner 250 ml
Removes heavy soiling, limescale deposits and aluminium
residues.
E-Cloth (microfibre cloth)
Removes finger marks and light soiling.
57
Optional accessories
Miele|home system
The Miele{home system allows communication-enabled
appliances to send operating and status information to a
display appliance via the household electrical supply system
(Powerline Technology).
SuperVision appliances can display status information from
other domestic appliances. For your hob, the main status
displayed is: On, Off, Fault
Status information for domestic appliances can be displayed
and some controls operated within the home network area on
a PC, Notebook or iPod* / iPhone* (mobile terminals) via a
Miele|home Gateway.
For your hob, for example, the following information is
displayed: Setting of each cooking zone, minute minder,
switching off time for each cooking zone. The only available
control command is "switch hob off".
* * iPod und iPhone are registered trade marks of Apple Inc.
Con|ctivity is the communication between the hob and the
cooker hood. Operation of the cooker hood occurs
automatically in conjunction with the hob.
The hob sends information on its operating status via the
household electrical supply.
XKM 2100 KM
XGW 2000
58
To enjoy the benefits of this feature, your appliance needs to
be fitted with a communication module.
Detailed information about the Miele|home system can be
found at www.miele.de.
Communication module including installation accessories
- for Miele hobs -
Miele|home Gateway
The gateway is the bridge between the Powerline
communication of the appliances and your home network.
Miele|home
Optional accessories
a Communication enabled appliances (examples)
b Communication module
c SuperVision appliance
d Electrical supply (Powerline)
e Miele|home Gateway
f WLAN) Router
Possible connections (optional)
g PC, Notebook
h iPod* or iPhone*
i Connection with a domestic bus system display
j Possible internet connection
* * iPod und iPhone are registered trade marks of Apple Inc.
59
Optional accessories
Con|ctivity
a Communication module XKM 2000 DA
b Communication module XKM 2100 KM
c Electrical supply (Powerline)
60
Signing on the hob
If you want to sign the hob
–
–
^
After selecting programming mode, P (Programme) and S
(Status) will appear in the timer display. On hobs with 3
cooking zones, an additional indicator will appear at the rear
left.
^ Touch the sensor for selecting the front left cooking zone
^ Touch the sensor for selecting the front right cooking zone
Con|ctivity and Miele|home
on to the Miele{home system, first prepare the signing on
procedure on the master appliance (see the "Miele|home"
fitting and installation instructions)
on to the Con|ctivity system, first sign on the cooker
hood (see the "Con|ctivity" fitting and installation
instructions).
With the hob switched off, touch the s and $ sensors atthe same time until the safety lock indicator light flashes.
and then touch the 1 on the numerical keypad (Set
Programme 10).
and then touch the 2 on the numerical keypad (Set Status 2
= Signed on).
The signing-on process starts, and the number 2 flashes. The
signing on process will take a few minutes. The number 2 will
light up constantly when the process has been completely
successfully.
^
To save the setting, touch the s sensor until all the
displays go out.
^
Proceed as described in the "Miele|home" or Con|ctivity
fitting and installation instructions.
61
Con|ctivity and Miele|home
Signing off the hob
If you want to sign off from the Miele{home system, first
prepare the signing off procedure on the master appliance
(see the "Miele|home" fitting and installation instructions).
With the hob switched off, touch the s and $ sensors at
^
the same time until the safety lock indicator light flashes.
After selecting programming mode, P (Programme) and S
(Status) will appear in the timer display. On hobs with 3
cooking zones, an additional indicator will appear at the rear
left.
Touch the sensor for selecting the front left cooking zone
^
and then touch the 1 on the numerical keypad
(Set Programme 10).
^ Touch the sensor for selecting the front right cooking zone
and then touch the 1 on the numerical keypad
(Set Status 1 = Signed off).
The signing-off process starts, and the number 1 flashes. The
signing off process will take a few minutes. The number 1 will
light up constantly when the process has been completed
successfully.
62
^ To save the setting, touch the s sensor until all the
displays go out.
^
Proceed as described in the "Miele|home" or Con|ctivity
fitting and installation instructions.
Safety instructions for installation
The appliance must only be installed
and connected to the electricity
supply by a suitably qualified and
competent person in strict
accordance with current national
and local safety regulations.
Fit the wall units and extractor hood
before fitting the hob to avoid
damaging the appliance.
After installing the hob, ensure that
~
the connection cable cannot come into
contact with the underside of the
appliance. Make sure that there is no
mechanical obstruction, such as a
drawer, which could damage it.
Observe carefully the safety
~
distances given on the following pages.
The veneer or laminate coatings of
~
worktops (or adjacent kitchen units)
must be treated with 100 °C
heat-resistant adhesive which will not
dissolve or distort.
Any backmoulds must be of
heat-resistant material.
The hob may not be built in over a
~
fridge, fridge-freezer, freezer,
dishwasher, washing machine or
tumble dryer.
This hob must not be installed
~
above ovens or cookers unless these
have a built-in cooling down fan.
All dimensions in this instruction booklet
are given in mm.
63
Safety instructions for installation
Safety distance above the appliance
When two or more appliances are
installed together below a cooker
hood, e.g. a gas wok and a ceramic
hob, which have different safety
distances given in the installation
instructions, you should select the
greater distance of the two.
A minimum safety distance must be
maintained between the appliance and
the cooker hood above it. See the
cooker hood manufacturer’s operating
and installation instructions for details.
If the manufacturer’s instructions are
not available for the cooker hood, a
minimum safety distance of at least
760 mm must be maintained. For any
flammable objects, e.g. utensil rails,
wall units etc. a minimum distance of at
least 760 mm must be maintained
between them and the appliance
below.
64
Safety instructions for installation
Safety distances to the sides and
back of the hob
Ideally the hob should be installed with
plenty of space on either side. There
may be a wall at the rear or a tall unit or
wall on one side (right or left) (see
illustrations).
a Minimum distance of 50 mm
between the back of the worktop
cut-out and the rear edge of the
worktop.
b Minimum distance of 50 mm
between the worktop cutout and a
wall or tall unit to the right of it.
c Minimum distance of 50 mm
between the worktop cutout and a
wall or tall unit to the left of it.
Not allowed
Recommended
Not recommended
Not recommended
65
Safety instructions for installation
Safety distances underneath the hob
To ensure sufficient ventilation to the
hob, a certain gap must be left between
the underside of the hob and any oven,
interim shelf or drawer.
The minimum gap between the
underside of the hob and
the top of an oven is 15 mm.
–
the top of an interim shelf is 15 mm.
–
the base of a drawer is 75 mm.
–
Interim shelf
It is not necessary to fit an interim shelf
underneath the hob, but one may be
fitted if you wish.
Leave a gap of 10 mm at the back of
the shelf to accommodate the cable.
We recommend a gap at the front of the
shelf of 20 mm to ensure good
ventilation.
66
Safety instructions for installation
Safety distance when installing the appliance near a wall with additional
niche cladding
A minimum safety distance must be maintained between the worktop cut-out and
any niche cladding to protect it from heat damage.
If the niche cladding is made from a combustible material (e. g. wood) a
minimum safety distance e of 50 mm must be maintained between the cut-out
and the cladding.
If the niche cladding is made from a non-combustible material (e. g. metal,
natural stone, ceramic tiles) a minimum safety distance e of 50 mm less the
thickness of the cladding must be maintained between the cut-out and the
cladding.
Example: 15 mm niche cladding
50 mm - 15 mm = minimum safety distance of 35 mm
Flush-fitted hobsHob with frame or bevelled edge
a Masonry
b Niche cladding
Dimension x = thickness of niche cladding material
c Worktop
d Worktop cut-out
d Minimum safety distance
for combustible materials is 50 mm
for non-combustible materials is 50 mm less dimension x
67
Safety instructions for installation
Hob with frame or bevelled
edges
Seal between the hob and the
worktop
The sealing strip under the edge of the
top part of the appliance provides a
sufficient seal for the worktop.
The hob must not be sealed with
sealant (e.g. silicone).
This could result in damage to the
hob or the worktop if the hob ever
needs to be removed for servicing.
Tiled worktop
Grout lines a and the hatched area
underneath the hob frame must be
smooth and even. If they are not the
hob will not sit flush with the worktop
and the sealing strip underneath the
hob will not provide a good seal
between the hob and the worktop.
68
KM 6314
Building-in dimensions
a Front
b Casing depth
c Miele|home connection box
d Mains connection box
The mains connection cable (1440 mm long) is supplied separately.
69
Building-in dimensions
KM 6317
a Front
b Casing depth
c Miele|home connection box
d Mains connection box
The mains connection cable (1440 mm long) is supplied separately.
70
KM 6318
Building-in dimensions
a Front
b Casing depth
c Miele|home connection box
d Mains connection box
The mains connection cable (1440 mm long) is supplied separately.
71
Building-in dimensions
KM 6340
a Front
b Casing depth
c Miele|home connection box
d Mains connection box
The mains connection cable (1440 mm long) is supplied separately.
72
KM 6342
Building-in dimensions
a Front
b Casing depth
c Miele|home connection box
d Mains connection box
The mains connection cable (1440 mm long) is supplied separately.
73
Installing the hob
Preparing the worktop
Make the worktop cut-out according
^
to the dimensions given in the
building-in diagram. Remember to
maintain the minimum safetydistances (see "Safety instructions
for installation").
Seal the cut surfaces on
^
wood/laminated worktops with a
suitable heat-resistant sealant to
avoid swelling caused by moisture.
Make sure that the sealant does not
come into contact with the top of the
worktop.
No spring clamps are needed to
install the hob. The sealing strip
underneath the hob positions it
securely in the cut-out.
Any gap between the frame and
worktop will reduce with time.
Installing the hob
Feed the mains connection cable
^
down through the cut-out.
Place the hob centrally in the cut-out.
^
When doing this, make sure that the
seal under the hob sits flush with the
worktop on all sides. This is important
to ensure an effective seal all round.
Do not use sealant (e.g. silicone).
If the corners of the frame are not
flush with the worktop surface, the
corner radius (ß R4) can be carefully
scribed to fit.
^ Connect the hob to the mains.
^ Check that the hob works.
Connecting the mains cable to the
appliance
The mains cable must only be
connected to the appliance by a
qualified and competent electrician
in strict accordance with current
local and national safety regulations
(BS 7671 in the UK).
^
Follow the instructions in the wiring
diagram (see "Electrical connection Wiring diagram").
74
All electrical work should be carried
out by a suitably qualified and
competent person, in strict
accordance with current local and
national safety regulations (BS 7671
in the UK).
Installation, repairs and other work
by unqualified persons could be
dangerous. The manufacturer
cannot be held liable for
unauthorised work.
A damaged cable must be replaced
by a suitably qualified electrician
with a special connection cable of
type H 05 VV-F, available from
Miele.
Electrical connection
Connection should be made via a
suitable isolator which complies with
national and local safety regulations,
and the On/Off switch should be easily
accessible after the appliance has
been built in.
If the switch is not accessible after
installation (depending on country) an
additional means of disconnection must
be provided for all poles.
For extra safety it is advisable to protect
the appliance with a residual current
device (RCD). Please contact a
qualified electrician for advice.
When switched off there must be an
all-pole contact gap of at least 3 mm in
the isolator switch (including switch,
fuses and relays).
Ensure power is not supplied to the
appliance until after installation or
repair work has been carried out.
The appliance must only be
operated when built-in. This is to
ensure that all electrical parts are
shielded. Live parts must not be
exposed.
Do not connect the appliance to the
mains electricity supply by an
extension lead. These do not
guarantee the required safety of the
appliance.
Please make sure that the connection
data quoted on the data plate match
the household mains supply.
Important U.K.
The appliance is supplied for
connection to a 230-240 V, 50 Hz
supply with a 3-core cable.
The wires in the mains lead are
coloured in accordance with the
following code:
Green/yellow = earth
Blue= neutral
Brown= live
WARNING
THIS APPLIANCE MUST BE
EARTHED
75
Electrical connection
The electrical safety of this appliance
can only be guaranteed when
continuity is complete between it and
an effective earthing system, which
complies with current local and national
safety regulations. It is most important
that this basic safety requirement is
present and regularly tested and where
there is any doubt, the electrical wiring
in the home should be inspected by a
qualified electrician. The manufacturer
cannot be held liable for the
consequences of an inadequate
earthing system such as an electric
shock.
The manufacturer cannot be held
liable for damage which is the direct
or indirect result of incorrect
installation or connection.
Wiring diagram
N.B. This appliance is supplied
single phase only in the U.K. / AUS /
NZ
76
After sales service, data plate, guarantee
In the event of any faults which you cannot remedy yourself, please contact:
your Miele dealer, or
–
Miele (see back of manual for contact details).
–
Please note that telephone calls may be monitored and recorded for training
purposes (UK only).
When contacting your Dealer or Miele, please quote the model and serial number
of your appliance. These are given on the data plate.
Space in which to stick the extra data plate supplied with the appliance. Ensure
that the model number is the same as the one on the back of these instructions.
Guarantee
For information on the appliance guarantee specific to your country please
contact Miele. See back of manual for contact details. In the UK, your appliance is
guaranteed for 2 years from the date of purchase. However, you must activate
your cover by calling 0845 365 6640 or registering online at www.miele.co.uk.
777879
KM 6314 / KM 6317 / KM 6318 / KM 6340 / KM 6342
M.-Nr. 07 798 980 / 07en-GB
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.