Page 1
30” Bottom Mount Refrigerator
KFN 9855 iDE LI/ KFN 9855 iDE RE
Shown: KFN 9855 iDE LI
Please note: This information is subject to change
Specification Sheets TRS 03282018
8mieleusa.com
Page 2
30” Bottom Mount Refrigerator
KFN 9855 iDE
SPECIFICATIONS
Overall Unit Dimensions 297/8” (759 mm) W x 7913/16” (2,027 mm) H x 24” (610 mm) D
Niche
Minimum Niche Opening Dimensions
Interior Volume
Fresh Food Volume 9.8 cu-ft (277.5 L)
Freezer Volume 4.3 cu-ft (127 L)
Plumbing
Water Supply Requirements
Water Connection Line
Electrical
Electrical Requirements - Volts/Amps
Power Cord - Plug NEMA 5-15 plug, 6’ 6” (2 m)
Custom Panel - Refer to manual for further detail
Maximum Refrigerator Door Panel Weight 60 lbs (27 kg)
Maximum Freezer Door Panel Weight Each 26.5 lbs (12 kg)
Maximum Panel Thickness 3/4” (19 mm)
Minimum Panel Thickness 5/8” (16 mm)
Shipping
Shipping Weight 345 lbs (156.5 kg)
Shipping Dimension 325/16” W x 8211/16” H x 291/8” D
Support
Call Miele (800) 999-1360
Miele Website
20/20 Link
Connect to a cold water supply only. Must be connected to a shut-off valve. The water shut-off valve must
be accessible after installation. The water pressure must be between 22 psi (1.5 bar) and may not exceed
87 psi (6 bar). If the pressure is higher than 87 psi (6 bar), a pressure reducing valve must be installed.
Unit comes with a male 3/4” BPT connection on back of unit. The connection parts included with the
appliance permit the connection of various water lines (included 1/4” compression fitting).
Water line is not included.
110V / 120V, 60Hz, 20A (2 Individual units installed side-by-side, using a Duplex outlet)
30 ” (762 mm) W x 80” (2,032 mm) H x 24” (610 mm) D
110V / 120V, 60Hz, 15A (single)
8www.mieleusa.com
82020technologies.com
KFN 9855 iDE LI (Left Hinged)
Item 38985552CDN
Hinging is not eld reversible.
KFN 9855 iDE RE (Right Hinged)
Item 38985551CDN
KFN 9855 iDE
Page 2 of 7
Page 3
Unit Dimensions
30” Bottom Mount Refrigerator
KFN 9855 iDE
29-7/8”
55-1/4”
(759 mm)
Power Cord exits at the top right when looking at the rear of the unit.
KFN 9855 iDE
Page 3 of 7
Page 4
Niche Dimensions and
Water Supply Connection
30” Bottom Mount Refrigerator
KFN 9855 iDE
Water Connection
• Water line feed-in (D) from left or right above the anit-tipping bracket.
• The water line lead-throught for the water supply line (E) is at the bottom right of
the appliance.
KFN 9855 iDE
Page 4 of 7
Page 5
30” Bottom Mount Refrigerator
KFN 9855 iDE
Inset Installation Panel
Dimensions
Stainless steel panels are available as
an optional Accessory
STAINLESS STEEL PANELS
Item#
Top Panel 38996045CDN
Bottom Panels 38996046CDN
Please note following:
-Stainless steel panels are not pre-drilled
-Handles are sold separately
Please take into account the followiong information concerning the cabinet front:
- The Panels should be at least 5/8” (16 mm) thick to allow the connecting rails to be fastened to them.
- The maximum panel thickness is 3/4” (19 mm).
- The refrigerator panel weight must not exceed 60 lbs (27 kg).
- Each freezer panel weight must not exceed 26.5 lbs (12 kg)
KFN 9855 iDE
Page 5 of 7
Page 6
Frameless Installation Panel
Dimensions
30” Bottom Mount Refrigerator
KFN 9855 iDE
Please take into account the followiong information concerning the cabinet front:
- The Panels should be at least 5/8” (16 mm) thick to allow the connecting rails to be fastened to them.
- The maximum panel thickness is 3/4” (19 mm).
- The refrigerator panel weight must not exceed 60 lbs (27 kg).
- Each freezer panel weight must not exceed 26.5 lbs (12 kg)
KFN 9855 iDE
Page 6 of 7
Page 7
Door Swing Dimensions
30” Bottom Mount Refrigerator
KFN 9855 iDE
KFN 9855 iDE
Specification Sheets TRS 03282018
Page 7 of 7
Loading...