Microtek ScanMaker 5950, ScanMaker ADF-650, ScanMaker ADF-651 Install Manual
The ADF-650/651 allows automatic scanning of up to 50 sheets of original scan
material from A6 size (4.14" x 5.83") up to legal size (8.5" x 14"). Sheets to be scanned
are fed from the feeder's top tray, guided and scanned as they pass the scanner's
image sensor, and then exit into the feeder's bottom tray.
The ADF-650/651 mounts onto the scanner in place of the scanner's document cover
or Transparent Media Adapter (TMA).
Checking the Package
The ADF-650/651 is packaged as an assembled unit, ready to be mounted on the
scanner . After unpacking the ADF-650/651, make sure that the following items are
included:
• ADF-650/651 unit
• Warranty Card
• ADF-650/651 Installing and Getting Started document
Introduction
The ADF-650/651 is an optional sheet feeder accessory for the Microtek ScanMakerseries of flatbed scanners. The ADF-650 is designed for the ScanMaker 5600,
ScanMaker 6700, and ScanMaker 6800, while the ADF-651 is designed for the
ScanMaker 5800 and ScanMaker 5900.
Copyright©2002 Microtek International, Inc. http://www.microtek.com
I49-003468 A, November 2002
Microtek ADF-650/651
Installing and Getting Started
This document describes the features of
the Automatic Document Feeder (ADF-650/
651) and provides information on how to
install the ADF-650/651.
Trademarks
Microtek®, ScanMakerTM, and
ScanWizardTM are
trademarks or registered
trademarks of Microtek
International, Inc.
Macintosh® and Apple® are
registered trademarks of
Apple Computer, Inc.
Windows® is a registered
trademark of Microsoft
Corporation. All other
products or name brands are
trademarks of their
respective holders.
Important
Documents you scan may be
protected under copyright
law. The unauthorized use of
such documents could be a
violation of the rights of the
copyright holder. Microtek
bears no responsibility for
the unauthorized use of
copyrighted materials.
ADF-650 ADF-651
2 Microtek ADF-650/651 Installing and Getting Started
Installing the ADF-650/651
Follow these steps to install the ADF-650/651:
1. Make sure that your flatbed scanner model
has a built-in 15-pin accessory port that is
compatible with your ADF-650/651.
2. Make sure your scanner has been installed
and works properly .
3 . Power off your scanner.
4. Remove the scanner cover. Open the cover until it stands vertically to the scanner,
then pull upward to remove.
5 . Hold the ADF-650/651 firmly on both sides
in a vertical position, with its hinge studs
and connector at the bottom. With the
feeder vertically positioned on the scanner,
carefully align and insert the feeder studs
into the hinge slots originally used by the
scanner cover (or TMA).
Note: The ADF-650/651 uses the same
connector as the Transparency Media
Adapter (TMA). If your scanner is equipped
with its own TMA (or document cover with
TMA combination), disconnect the TMA and
remove from the scanner before installing
the ADF-650/651.
15-pin Accessory port
Microtek ADF-650/651 Installing and Getting Started 3
6. Remove the protective film from the transparent cover of the scan sensor area,
then lower the ADF-650/651.
7. Plug the feeder's connector into the 15-pin Accessory port at the back panel of the
scanner. Secure the connector by tightening the retaining screws.
8. Turn on your scanner, and wait for the light on the scanner’s front panel to stop
blinking and stay on steady . Your system will detect the scanner with ADF-650/
651 automatically , indicating that the ADF-650/651 is ready to scan.
15-pin
connector
Protective film
Loading...