Medion MD 5232 user Manual
SETTING THE CLOCK TO THE CORRECT TIME OF DAY
Set the CLOCK SETTING SWITCH to the time set position, and
then rotate the ROTARY SET DIAL to the left (MINUTE) or
right (HOUR) hand side to set the current time. Once the time is set,
set the CLOCK SETTING SWITCH to RUN position to stop the
2 flashing dots and avoid resetting the clock.
SETTING THE ALARM TIME
Set the CLOCK SETTING SWITCH to the alarm set position,
and then rotate the ROTARY SET DIAL to the left (MINUTE)
or right (HOUR) hand side to set the alarm time. Once the time is set,
set the CLOCK SETTING SWITCH to RUN position to stop the
2 flashing dots and avoid resetting the alarm time.
NOTE:
Do not rotate the dial too quickly when you are setting the time, other-
wise the clock radio will not keep up with your setting speed.
to the OFF position.
4
6. The radio can be switched off by setting the POWER SWITCH
to its full extent.
waveband.
POWER CONNECTION
Plug the AC POWER CORD to the household outlet (230 v~ 50 Hz).
Make sure the voltage is correct for safety purpose and prevent possible
damage to the unit.
RADIO OPERATION
1. Set the POWER SWITCH to the ON position.
2. Set the AM/FM BAND SELECTION SWITCH to the desired
3. Tune to the desired station with the TUNING CONTROL.
4. Adjust the volume level with the VOLUME CONTROL.
5. To obtain better FM reception, lay out the FM ANTENNA WIRE
Projection Clock MD_5232_BDA.FH11 Mon Jul 19 14:30:49 2004 Seite 3
C M Y CM MY CY CMY K
Projection Clock MD_5232_BDA.FH11 Mon Jul 19 14:30:49 2004 Seite 4
the selected alarm time.
Remove the lid of the battery compartment at the rear of the unit.
Connect both plug-and-socket-connections of the battery with those on
the unit. Observe the polarity (+/-)!
Insert the battery and close the battery compartment.
Used batteries are not household refuse. Flat batteries must be disposed
of at designated disposal/recycle points
Please note: The display will not display the time during power failure
but the clock will keep the correct time.
BATTERY BACKUP SYSTEM
In order to guarantee an uninterrupted clock function, you can insert a
9 Volt block battery (not included). Make sure the unit is connected to
the mains when inserting it!
ALARM RADIO OR BUZZER
Set the POWER SWITCH to the AUTO position.
Radio
Wake to radio:
The radio must be tuned to a radio station and the volume set to the
desired level. The radio will switch on at the selected alarm time.
Buzzer
Wake to buzzer:
Slide the VOLUME BUZZ SWITCH to the BUZZ
position until you hear a CLICK sound. The buzzer will switch on at
5
C M Y CM MY CY CMY K
Projection Clock MD_5232_BDA.FH11 Mon Jul 19 14:30:49 2004 Seite 5
SLEEP TO RADIO AND WAKE TO RADIO
3. The radio will switch off after the SLEEP time has elapsed and
the radio alarm will switch on again the next day.
2. Set sleep time as described in the SLEEP BUTTON section and
set the volume.
1. Set the desired alarm time as described in SETTING THE ALARM
TIME. Tune the radio to the desired radio station.
Set the POWER SWITCH to the AUTO position.
3. After the pre-selected SLEEP time has elapsed, the radio will switch
off automatically. To switch it off before the preselected SLEEP
time has elapsed, press the SNOOZE BUTTON.
2. Press the SLEEP BUTTON, and then rotate the dial to the left
(your desired time which is within 1 hour 59 min) or right (time fixed
at 1 hour 59 min) to set the sleep time.
1. This clock radio is equipped with a SLEEP TIMER function which
will switch off the radio automatically after a preselected period from
1 hour 59 minutes to 1 minute.
SNOOZE FUNCTION
The alarm can be interrupted for 9 minutes by pressing the SNOOZE
BUTTON, after that time the radio or the alarm buzz will sound again.
SWITCHING OFF THE ALARM
To switch off the alarm, set the POWER SWITCH to the OFF position.
SLEEP TIMER OPERATION
6
C M Y CM MY CY CMY K
Loading...