MAMAC Systems IP-PC-101-44-VDC User Manual

Installation & Operating Instructions

Maverick

IP Sensor Appliance

Model IP-PC-101-44-VDC

Baird House, Units 6&7

Pensnett Estate • Kingswinford

West Midlands • DY6 7YA • United Kingdom

01384-271113 • Fax [phone]

RoHS

8189 Century Blvd. • Minneapolis, MN 55317-8002 • USA

800-843-5116 • 952-556-4900 • Fax [phone]

[e-mail] • www.mamacsys.com

4 Arminger Court, Unit 2

Holden Hill • S.A. 5088 • Australia

08-8395-4333 • Fax [phone]

® Registered trademark MAMAC SYSTEMS, Inc.

155 McIntosh Drive, Units 5&6 • Markham

Ontario • L3R ON6 • Canada

905-474-9215 • Fax [phone]

No. 22 Lorong 21A Geylang # 11-02

Prosper Industrial Building

Singapore • 388421

656-3927273 • Fax [phone]

TABLE OF CONTENTS

SECTION 1: Maverick Overview

1.0.0: Conformance and Testing

1.1.0: Specifications

1.2.0: Appliance Overview

1.3.0: Installation

1.4.0: Wiring

SECTION 2: Initial Configuration

2.0.0: Initial Configuration

2.1.0: Internet Protocol

2.2.0: Network & Email Configuration - Static IP

2.3.0: Network & Email Configuration - DHCP

2.4.0: Password/Clock Configuration

2.5.0: Sensor Inputs, Email Alert & Setpoint Control Configuration

Page 2

Page 3

Page 4

Page 5

Page 6

Page 7

Page 8

Page 9

Page 9

Page 10

Page 11,12

2.6.0: Output Configuration

2.7.0: Data Logging

SECTION 3: Operation

3.0.0: Network Configuration - Static IP

3.0.1: Network Configuration - DHCP IP

3.1.0: Main Page

3.1.1: Manual Control

3.1.2: Data Logging

3.2.0: Reset Button

3.3.0: XML

Page 13

Page 14

Page 15

Page 16

Page 17

Page 18

Page 19

Page 20

Page 20

® Registered trademark MAMAC SYSTEMS, Inc.

1 of 20

© Copyright 2008DN IS-IPPC101.1

SECTION 1 - Conformance & Testing

1.0.0

1.0.1

FCC Testing -

- Rule Part 15, Subpart B - Unintentional Radiators Class B Limits 15.107 & 15.109.

EMC/EMI Testing -

- BS EN 55022:1998, CISPR 22:1997 Amendments 1 & 2.

- BS EN 55024:1998 CISPR 24:1997 Amendments 1 & 2.

- EN 61000-3-3: Limitations of voltage fluctuations and flicker in low-voltage supply systems <16A.

- EN 61000-4-2: Electrostatic Discharge (ESD).

- EN 61000-4-3: Radiated, radio frequency, Electromagnetic field immunity test.

- EN 61000-4-4: Electrical Fast Transient/burst immunity test (EFT).

- EN 61000-4-5: Surge Immunity Test (Mains).

- EN 61000-4-6: Immunity to conducted disturbances induced by radio frequency fields.

- EN 61000-4-11: Voltage dips, short interruptions and voltage variations immunity test.

1.0.2

RoHS Compliant -

MAMAC Systems, Inc. products designated “RoHS Compliant” comply with the European

Union’s Directive on the Restriction of the Use of Hazardous Substances 2002/95/EC

(”RoHS”). These products do not contain Joint Industry Guide (JIG) - 101 Level A substances

above threshold limits, except lead in RoHS exempt applications 5, 7a and 7c. These products

do not contain perfluorooctane sulfonates (PFOS).

- Cadmium (Cd) < 100 ppm

- Mercury (Hg) < 100 ppm

- Lead (Pb) < 1000 ppm

- Polybrominated Biphenyls (PBB) < 1000 ppm

- Polybrominated Diphenyl Ethers (PBDE) < 1000 ppm

- Hexavalent Chromium (CrVI) < 1000 ppm

® Registered trademark MAMAC SYSTEMS, Inc.

2 of 20

© Copyright 2008DN IS-IPPC101.1

SECTION 1 - Specifications

1.1.0

Anyone who can surf the web now can do sensor monitoring, control,
data logging, and email alerts without any training or custom software.
All you need is a web browser running on any laptop, PDA, or cell
phone anywhere in the world.

The

Maverick IP Sensor Appliance incorporates a web server,

analog/digital inputs and relay outputs. Power the appliance with
any 24VAC transformer, plug it into a hub/router, launch any web
browser, punch in the default IP and connect. No custom software to
load, no discovery routines, no custom cables, or training.

The IP Sensor Appliance serves up static web pages with dynamic
data updates every second or two. Most users can set up and utilize
the appliance without any training or support in less than 5 minutes
due to the innovative and familiar web browser based configuration.

The

Maverick is an ideal low cost solution for light commercial,

residential and remote monitoring applications. The appliance can
also be used to enhance existing HVAC control systems by adding
email alerts and data logging to critical points.

SPECIFICATIONS:

Supply Voltage: 24 VAC/VDC Data Logging: 2048 samples each input

Supply Current: 250 mA (6 VA)

Input Impedance: 125K ohms (VDC or

Digital) 250 ohms (4-20 mA)

Digital Input: 10.00 VDC maximum

Output Relay Rating: 250 VAC @ 5.0 Amps

UL Listed

Ethernet: 10-Base T

IP Assignment: Static or DHCP

Logging Interval: 1.0 second to 99.99 hours

Environmental: 10-90%RH non-condensing

Operating Temp: -40˚F-125˚F (-40˚C-52˚C)

Storage Temp: -40˚F-150˚F (-40˚C-66˚C)

Enclosure: UL 94V-5-O Polycarbonate plastic

Termination: Removable terminal blocks 16

Ga max, RJ-45 Ethernet jack

Email: SMTP to two email addresses

® Registered trademark MAMAC SYSTEMS, Inc.

Weight: 0.5 lbs. (.25 kg)

© Copyright 2008DN IS-IPPC101.1

3 of 20

1.2.0

SECTION 1 - Appliance Overview

Figure 1

Lan

Link

Heart Beat

Power

LEDs

Reset

Button

LEDs

Out 1 NC

Out 1 COM

Out 1 NO

Out 2 NC

Out 2 COM

Out 2 NO

Out 3 NC

Out 3 COM

Out 3 NO

Out 4 NC

Out 4 COM

Out 4 NO

Output 1

Output 2

Output 3

Output 4

MAMAC SYSTEMS

24 VAC/VDC
Neutral/Com
Ground/Earth

Input 1
Common
Input 2
Common
Input 3
Common
Input 4
Common

® Registered trademark MAMAC SYSTEMS, Inc.

4 of 20

© Copyright 2008DN IS-IPPC101.1

SECTION 1 - Installation

1.3.0

1.3.1

INSPECTION:

Inspect the package for damage. If damaged, notify the appropriate carrier immediately.

REQUIREMENTS:

• Tools (not provided)

- Digital Volt-ohm Meter (DVM).

- Appropriate screwdriver for mounting screws.

- Appropriate drill and drill bit for mounting screws.

• Four #6 sheet metal screws.

• Training: Installer must be a qualified, experienced technician.

Warning:

• Disconnect power supply before installation to prevent electrical shock and
equipment damage.

• Make all connections in accordance with national and local electrical codes. Use copper
conductors only.

Caution:

• Use electrostatic discharge precautions (e.g., use of wrist straps) during installation and
wiring to prevent equipment damage.

• Avoid locations where severe shock or vibration, excessive moisture or corrosive fumes
are present.

• Do not exceed ratings of the device.

1.3.2

MOUNTING:

The Maverick IP Sensor Appliance must be mounted on a flat surface with four #6 sheet
metal screws (not provided) as shown in fig. 2.

Figure 2

4.50”

3.60”

(114 mm)

(91 mm)

4.00”

(102 mm)
4x 0.156” use #6 sheet
metal screws (not
included), to mount

MAMAC SYSTEMS

3.70”

(94 mm)

appliance

® Registered trademark MAMAC SYSTEMS, Inc.

5 of 20

© Copyright 2008DN IS-IPPC101.1

SECTION 1 - Wiring

1.4.0

1.4.1

Terminate the IP Sensor Appliance as shown in fig. 3.

Use a UL rated 24VAC class-2 transformer or a UL rated 24VDC power supply with
transformer isolation.

WARNING:
Maximum supply voltage MUST NOT EXCEED 35VAC/35VDC.

CAUTION:

The appliance and all sensors connected must be wired with all neutral/common
connections with the same polarity. All sensors and the appliance neutral/common must
terminate at the transformer/power supply neutral/common.

Figure 3

Signal

Common

Supply

Sensor “n”

MAMAC SYSTEMS

Note: Use 18 gauge conductor
for ground.

Note:

Always disconnect
power from unit before
wiring a sensor.

Signal

Common

Supply

Sensor 2

1.4.2

Signal

Common

Supply

Sensor 1

Digital inputs are terminated as shown in fig. 4.

Figure 4

Digital

Input #1

Digital

Input #2

WARNING: Digital Input
must not exceed 10.0 VDC.

24 VAC/VDC

TRANSFORMER/POWER SUPPLY

Neutral/Common

24 VDC/VAC

MAMAC SYSTEMS

® Registered trademark MAMAC SYSTEMS, Inc.

6 of 20

© Copyright 2008DN IS-IPPC101.1