Makita MT240 Manual

Portable Cut-Off

MODEL MT240

003979

DOUBLE

INSULATION

I N S T R U C T I O N M A N U A L

WARNING:

For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

SPECIFICATIONS

Model	MT240
Wheel diameter	355 mm
Hole diameter	25.4 mm
No load speed (min-1)	3,800
Dimensions (L x W x H)	500 mm x 280 mm x 620 mm
Net weight	15.9 kg
Safety class	/II

•Manufacturer reserves the right to change specifications without notice.

•Specifications may differ from country to country.

SYMBOLS

END201-2

The following show the symbols used for the tool. Be sure that you understand their meaning before use.

...............Read instruction manual.

...............DOUBLE INSULATION

..............Only for EU countries

Do not dispose of electric equipment together with household waste material!

In observance of European Directive 2002/96/EC on waste electric and electronic equipment and its implementation in accordance with national law, electric equipment that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.

Intended use

The tool is intended for cutting in masonry and ferrous materials with appropriate abrasive cut-off wheel.

Power supply

The tool should be connected only to a power supply of the same voltage as indicated on the nameplate, and can only be operated on single-phase AC supply. They are double-insulated in accordance with European Standard and can, therefore, also be used from sockets without earth wire.

For public low-voltage distribution systems of between 220 V and 250 V.

Switching operations of electric apparatus cause voltage fluctuations. The operation of this device under unfavorable mains conditions can have adverse effects to the operation of other equipment. With a mains impedance equal or less than 0.31 Ohms it can be presumed that there will be no negative effects. The mains socket used for this device must be protected with a fuse or protective circuit breaker having slow tripping characteristics.

2

For European countries only

Noise and Vibration

The typical A-weighted noise levels are sound pressure level: 98 dB (A)

sound power level: 111 dB (A)

– Wear ear protection. –

The typical weighted root mean square acceleration value is not more than 2.5 m/s2.

EC-DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product is in compliance with the

following standards of standardized documents, EN61029, EN55014, EN61000 in accordance with Council Directives, 73/23/ EEC, 89/336/EEC, 98/37/EC.

Yasuhiko Kanzaki CE 2002

Director

MAKITA INTERNATIONAL EUROPE LTD.

Michigan Drive, Tongwell, Milton Keynes,

Bucks MK15 8JD, ENGLAND

SAFETY INSTRUCTIONS

ENA001-2

WARNING:

When using electric tools, basic safety precautions, including the following, should always be followed to reduce the risk of fire, electric shock and personal injury. Read all these instructions before operating this product and save these instructions.

For safe operations:

1.Keep work area clean.

Cluttered areas and benches invite injuries.

2.Consider work area environment.

Do not expose power tools to rain. Do not use power tools in damp or wet locations. Keep work area well lit. Do not use power tools where there is risk to cause fire or explosion.

3.Guard against electric shock.

Avoid body contact with earthed or grounded surfaces(e.g. pipes, radiators, ranges, refrigerators).

4.Keep children away.

Do not let visitors touch the tool or extension cord. All visitors should be kept away from work area.

5.Store idle tools.

When not in use, tools should be stored in a

dry, high or locked up place, out of reach of children.

6.Do not force the tool.

It will do the job better and safer at the rate for which it was intended.

7.Use the right tool.

Do not force small tools or attachments to do the job of a heavy duty tool. Do not use tools for purposes not intended; for example, do not use circular saws to cut tree limbs or logs.

8.Dress properly.

Do not wear loose clothing or jewellery, they can be caught in moving parts. Rubber gloves and non-skid footwear are recommended when working outdoors. Wear protecting hair covering to contain long hair.

9.Use safety glasses and hearing protection.

3

Also use face or dust mask if the cutting operation is dusty.

10.Connect dust extraction equipment.

If devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used.

11.Do not abuse the cord.

Never carry the tool by the cord or yank it to disconnect it from the socket. Keep the cord away from heat, oil and sharp edges.

12.Secure work.

Use clamps or a vice to hold the work. It is safer than using your hand and it frees both hands to operate the tool.

13.Do not overreach.

Keep proper footing and balance at all times.

14.Maintain tools with care.

Keep cutting tools sharp and clean for better and safer performance. Follow instructions for lubrication and changing accessories. Inspect tool cord periodically and if damaged have it repaired by an authorized service facility. Inspect extension cords periodically and replace, if damaged. Keep handles dry, clean and free from oil and grease.

15.Disconnect tools.

When not in use, before servicing and when changing accessories such as blades, bits and cutters.

16.Remove adjusting keys and wrenches.

Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning it on.

17.Avoid unintentional starting.

Do not carry a plugged-in tool with a finger on

the switch. Ensure switch is off when plugging in.

18.Use outdoor extension leads.

When tool is used outdoors, use only extension cords intended for outdoor use.

19.Stay alert.

Watch what you are doing. Use common sense. Do not operate tool when you are tired.

20.Check damaged parts.

Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, free running of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated in this instruction manual. Have defective switches replaced by an authorized service facility. Do not use the tool if the switch does not turn it on and off.

21.Warning.

The use of any accessory or attachment, other than those recommended in this instruction manual or the catalog, may present a risk of personal injury.

22.Have your tool repaired by a qualified person.

This electric tool is in accordance with the relevant safety requirements. Repairs should only be carried out by qualified persons using original spare parts, otherwise this may result in considerable danger to the user.

ADDITIONAL SAFETY RULES FOR TOOL ENB066-1

1.Wear protective glasses. Also wear hearing protection during extended periods of operation.

2.Use only wheels recommended by the manufacturer which have a maximum

operating speed at least as high as “No Load RPM” marked on the tool’s nameplate. Use only fiberglass-reinforced cutoff wheels.

4