Explanation of symbols used in this manual and on the product:
This symbol is intended to alert the user to the presence of
uninsulated dangerous voltages within the enclosure of sufficient
magnitude to cause electric shock.
This symbol is intended to alert the user to the presence of
important maintenance and servicing information in the instruction
and service manuals.
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE THE
COVER.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING: SHOCK HAZARD. DO NOT OPEN.
AVIS: RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR.
CAUTION: REPLACE FUSE WITH SAME TYPE AND RATING.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE.
DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE.
ATTENTION: DEBRANCHER AVANT DE REMPLACER LE FUSIBLE.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
MAINS PLUGS
This appliance is supplied with a non-rewireable mains plug for the
intended country.
Replacement mains leads can be obtained from your Linn retailer.
Should you need to change the plug please dispose of it carefully.
A plug with bared conductors is dangerous if engaged in a live socket.
The Brown wire must be connected to the Live (Line) supply pin.
The Blue wire must be connected to the Neutral supply pin.
The Green/Yellow wire must be connected to the Earth (Ground) supply
pin.
Please contact your retailer or a competent electrician if you are in any
doubt.
i
ii
UK USERS PLEASE READ THIS IMPORTANT SAFETY
INFORMATION
Fuse replacement
This appliance is fitted with a non-rewireable 13 Amp mains plug. The plug
contains a 5 Amp fuse. If the fuse has blown it can be replaced as follows:
a) Pull out the red fuse cover/carrier.
b) Remove and dispose of the blown fuse.
c) Fit a new 5 Amp BS1362 approved fuse into the carrier and push the
carrier back into the plug.
Always ensure the fuse cover is fitted. If the fuse cover is missing do not
use the plug. Contact your Linn retailer to obtain a replacement fuse cover.
Fuses are for fire protection and do not protect against electric shock.
Mains plug replacement
Should your mains plug need replacing and you are competent to do this
proceed as follows. If you are in doubt contact your Linn retailer or a
competent electrician.
a) Disconnect the plug from the mains supply.
b) Cut off the plug and dispose of it safely. A plug with bared conductors
is dangerous if engaged in a live socket.
c) Only fit a 13 Amp BS1363A approved plug with a 5 Amp fuse.
d) The cable wire colours or a letter will be marked at the connection
points of most quality plugs.
Attach the wires securely to their respective points. The Brown wire
must go to the Live pin, the Blue wire must go to the Neutral pin, and
the Green/Yellow wire must go to the Earth pin.
e) Before replacing the plug top ensure that the cable restraint is holding
the outer sheath of the cable firmly and that the wires are correctly
connected.
WARNING
THIS APPLIANCE MUST BE EARTHED.
Replacing the fuse
Should the mains fuse blow replace it only with an equivalent part. The fuse
holder is located just below the mains inlet socket. To replace the fuse
disconnect the product from the mains supply. Using a flat blade
screwdriver remove and replace the fuse. If the fuse blows a second time
there is a fault in the product. Contact your local retailer.
Fuse ratings. See specifications section.
Mains voltage operating range. See specifications section.
Warning!! The power supply may be destroyed if a unit
designed for 115V is connected to 230V.
iii
iii
CE Declaration of Conformity
Linn Products Ltd declare that this product is in conformance with the LowVoltage Directive 73/23/EEC and Electromagnetic Compatibility 89/336/EEC as amended by 92/31/EEC and 93/68/EEC.The conformity of the designated product with theprovisions of Directivenumber 73/23/EEC (LVD) is proved by full compliance withthe followingstandards:
Standard numberDateof issueTest typeEN60065 1998 General requirements
MarkingHazardous radiationHeating under normal conditionsShock hazards under normaloperating conditionsInsulation requirementsFault conditionsMechanical strengthParts connected to the mains supplyComponentsTerminal devicesExternal flexible cordsElectrical connections andmechanical fixingsProtection against electric shockStability and mechanical hazardsResistance to fire
iv
The conformity of the designated product with the provisions of Directivenumber 89/336/EEC (EMC) is proved byfull compliance with the followingstandards:
Standard numberDate of issueTest typeEN55013 2001 Conducted emissionsEN55013 2001 Absorbed emissionsEN55020 2002 Immunity
FCC notice
NOTE: This equipment has been tested and found to comply with thelimits for aClass B digital device, pursuant to Part 15 of the FCC Rules.These limits are designedto provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, usesand can radiate radio frequency energyand, if not installed and used inaccordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee thatinterference will notoccur in a particular installation.If this equipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more ofthe following measures:
–Reorient or relocate the receiving antenna.–Increase the separation between the equipment and receiver.–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.–Consult the dealer or an experienced radio/TV technician for help.
Linn Products Limited, Floors Road, Waterfoot, Glasgow, G76 0EP, Scotland, United
Kingdom.
All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system, or transmitted, in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior written
permission of the publisher.
Printed in the United Kingdom.
LK85 and LK140 are trademarks of Linn Products Limited.
The information in this manual is furnished for informational use only, is subject to
change without notice, and should not be construed as a commitment by Linn
Products Limited. Linn Products Limited assumes no responsibility or liability for any
errors or inaccuracies that may appear in this manual.
Part no: PACK 326
This manual was produced by Human-Computer Interface Ltd, Cambridge,
England.
Loading...
+ 16 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.