V 2.0
Setup Guide
Setup Guide
Setup GuideSetup Guide
Revised: 04-12-00
Contents:
1111 Connecting the System 2
2222 Digital 328 Setup 3
Digital 328 v2 and
Digital 328 v2 and
Digital 328 v2 andDigital 328 v2 and
Lexicon Studio LDI-12T
Lexicon Studio LDI-12T
Lexicon Studio LDI-12TLexicon Studio LDI-12T
3333 Lexicon Studio LDI-12T Setup 5
Lexicon Studio Setup Guide
1
Connecting
Connecting The System
Connecting Connecting
1
Audio Connections
Audio Connections
Audio ConnectionsAudio Connections
Connect audio connections as shown in the diagram below. Toslink Optical cables must be
connected from the ADAT Out port of the Lexicon Studio LDI-12T card to an ADAT In port of the
Digital 328 and vice versa. Coaxial digital S/PDIF cables can also be connected from the Lexicon
Studio LDI-12T S/PDIF output to the Digital 328 S/PDIF input and vice versa. The recommended
method of synchronization is to utilize the Wordclock Out feature of the Digital 328.
The System
The SystemThe System
328 Wordclock
Out Î Lexicon
Studio
Wordclock In
328 ADAT Out 1 Î Lexicon Studio
ADAT In
Lexicon Studio ADAT Out Î 328
ADAT In 1
The ADAT connections allow digital transfer of either direct output for input channels 1-16 to the
Lexicon Studio LDI-12T card, or the Digital 328’s 8 Group outputs. The S/PDIF output from the
console can be assigned to either the Mix output or 1 of 3 stereo auxiliary outputs. The 328
S/PDIF Input can be configured to be a digital Stereo Input or as a digital 2 Track Return.
Lexicon Studio S/PDIF Out Î
328 S/PDIF In
328 S/PDIF Out Î Lexicon
Studio S/PDIF In
2
Spirit Digital 328 v2
<Wordclock S
>
<Wordclock S
>
<T
Ch17->24 >
Wordclock
Wordclock
WordclockWordclock
To configure the Digital 328 as the wordclock master, enter the 328 Menu pages by pressing the
<MENU> button on the right hand side of the LCD display. Using the encoder beneath the
display, scroll up or down until the ‘Clock Source Sel’ menu is highlighted, and press <ENTER>.
Here, either the internal 44.1kHz clock or the internal 48kHz clock must be selected, depending
on the sampling rate at which work is to be done. Press <ENTER> to set the sample rate and
<MENU> to return to the menu pages.
Digital 328 Setup
Digital 328 Setup
Digital 328 SetupDigital 328 Setup
2
Internal:44.1kHz
Tape Ports
Tape Ports
Tape PortsTape Ports
To ensure that the Digital 328 Tape Ports are set to ADAT to work with the Lexicon Studio LDI12T, enter the 328 Menu pages by pressing the <MENU> button on the right hand side of the
LCD display. Using the encoder beneath the display, scroll up or down until the ‘Tape Port Select’
menu is highlighted. Press <ENTER> and keep pressing the Up cursor arrow until the
‘<Tape Ch17-24 >’ menu page is displayed. Using the encoder set the Bank Source to ADAT.
Press the Down cursor arrow once, to set the wordlength. The Lexicon Studio LDI-12T is capable
of 24-bit recording, and so for optimum results, 24-bit wordlength can be selected here. If your
audio sequencer software does not allow 24-bit recording, 20-bit or 16-bit should be selected.
The sequencer manuals should be consulted for further information. The wordlength is set on
the 328 with the encoder. Press <ENTER> to set the wordlength and <MENU> to return to
the menu pages.
rc.
ape
Bank Source:ADAT
or
Internal:48.0kHz
rc.
<Tape Ch17->24 >
Wordlength: 24
Lexicon Studio Setup Guide
3
<T
Ch25->32 >
R
R
< SPDIF
>
R
< SPDIF
>
R
<T
Ch25->32 >
S/PDIF Input
S/PDIF Input
S/PDIF InputS/PDIF Input
The 328 S/PDIF input can be routed to any one of the following inputs:
Stereo Input 1;
Stereo Input 2;
FX Return 1;
FX Return 2;
2 Track Tape Return,
provided that the AES/EBU input has not already been assigned to that input. Commonly the
Lexicon Studio LDI-12T S/PDIF output would best be routed to Stereo Input 1 or the 2 Track
Tape Return input.
ape
Bank Source:ADAT
ape
Wordlength: 24
NOTE
Press <MENU> to enter the menu pages, scroll through the pages until the ‘SPDIF I/P Setup’ is
highlighted and press <ENTER>. Using the encoder, select the destination for the S/PDIF
input, press <ENTER> to set and <MENU> to return to the menu pages.
NOTE
< SPDIF Input >
Assigning a digital source to an input will override an analogue signal, if
present.
If the S/PDIF input is not required, NOWHERE should be selected in the
menu.
< SPDIF Input >
oute To: STE-1
Input
oute To: 2TRK
oute To: FX-1
Input
oute To:NOWHERE
4
Spirit Digital 328 v2
Wordclock
Wordclock
WordclockWordclock
The Lexicon Studio LDI-12T must now be set up to receive the wordclock transmitted by the
328. Open the Lexicon Studio Control Panel, by double clciking the Lexicon Studio icon in the
taskbar. and select ‘Clock Source’ from the page options.
Lexicon Studio LDI-12T
Lexicon Studio LDI-12T
Lexicon Studio LDI-12TLexicon Studio LDI-12T
3
Click on the drop down menu and select WCBNC as the clock source input.
If you do not have a wordclock cable connected, the Lexicon Studio LDI-12T must slave to
the clock on one of its ADAT or S/PDIF inputs. Set the Lexicon Studio LDI-12T to use the clock
source from the ADATDATA 12T input or the SPDIF 12T Input as required using the method
described above.
If the wordclock cable is available, the Lexicon Studio LDI-12T should slave to the clock on
the BNC wordclock input.
Lexicon Studio Setup Guide
5
Audio Data
Audio Data
Audio DataAudio Data
The Lexicon Studio LDI-12T must now be set up to transmit and receive audio data to and from
the Digital 328. Open the Lexicon Studio Control Panel, by double clciking the Lexicon Studio
icon in the taskbar. and select ‘CtrlI/O’ from the page options.
Leave the virtual faders for the input and output level at their default positions, this is correct for
the Digital 328.
Now select S/PDIF RCA in the ‘Input’ settings, this forces the Core32 to recieve the ADAT signal
from the Digital 328.
The in the ‘Output’ settings select S/PDIF RCA / ADAT OPTICAL, this forces the Core32 to send
audio from the ADAT port to the Digital 328.
Please refer to the Lexicon Studio Documentation for other system settings.
6
Spirit Digital 328 v2
Spirit by Soundcraft
Harman International Industries Ltd., Cranborne House,
Cranborne Road, Potters Bar, Herts EN6 3JN, England.
Tel: +44 (0)1707 665000 Fax: +44 (0)1707 665461
web: http://www.spiritbysoundcraft.com
e-mail: spiritsupport@soundcraft.com
spiritdig@harman.com (US)
Lexicon Studio Setup Guide
7
Loading...