Lexicon FW810S Owner's Manual
Owner's Manual
IMPORTANT SAFETY INSTRUCTIONS
WARNING FOR YOUR PROTECTION
PLEASE READ THE FOLLOWING:
KEEP THESE INSTRUCTIONS
HEED ALL WARNINGS
FOLLOW ALL INSTRUCTIONS
THE APPARATUS SHALL NOT BE EXPOSED
TO DRIPPING OR SPLASHING LIQUID AND
NO OBJECT FILLED WITHI LIQUID, SUCH AS
VASES, SHALL BE PLACED ON THE APPARATUS.
CLEAN ONLY WITH A DRY CLOTH.
DO NOT BLOCK ANY OF THE VENTILATION
OPENINGS. INSTALL IN ACCORDANCE
WITH THE MANUFACTURER’S INSTRUCTIONS.
DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS RADIATORS, HEAT REGISTERS,
STOVES, OR OTHER APPARATUS (INCLUDING AMPLIFIERS) THAT PRODUCE HEAT.
ONLY USE ATTACHMENTS/ACCESSORIES
SPECIFIED BY THE MANUFACTURER.
SAFETY INSTRUCTIONS
NOTICE FOR CUSTOMERS IF YOUR UNIT IS EQUIPPED WITH A POWER CORD.
WARNING: THIS APPLIANCE SHALL BE CONNECTED TO A MAINS SOCKET
OUTLET WITH A PROTECTIVE EARTHING CONNECTION.
The cores in the mains lead are coloured in accordance with the following code:
GREEN and YELLOW - Earth BLUE - Neutral BROWN - Live
As colours of the cores in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug,
proceed as follows:
•
The core which is coloured green and yellow must be connected to the
terminal in the plug marked with the letter E, or with the earth symbol,
or coloured green, or green and yellow.
•
The core which is coloured blue must be connected to the terminal
marked N or coloured black.
•
The core which is coloured brown must be connected to the terminal
marked L or coloured red.
This equipment may require the use of a different line cord, attachment
plug, or both, depending on the available power source at installation.
If the attachment plug needs to be changed, refer servicing to qualified
service personnel who should refer to the table below. The green/yellow
wire shall be connected directly to the units chassis.
CONDUCTOR
L LIVE BROWN BLACK
N NEUTRAL BLUE WHITE
E EARTH GND GREEN/YEL GREEN
WARNING: If the ground is defeated, certain fault conditions in the unit
or in the system to which it is connected can result in full line voltage
between chassis and earth ground. Severe injury or death can then result if
the chassis and earth ground are touched simultaneously.
WIRE COLOR
Normal Alt
UNPLUG THIS APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR
LONG PERIODS OF TIME.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or third prong
are provided for your safety. If the provided plug
does not fit your outlet, consult an electrician
for replacement of the obsolete outlet.
Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
Use only with the cart stand, tripod bracket, or
table specified by the manufacture, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
Refer all servicing to to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
POWER ON/OFF SWITCH: The Power switch
used in this piece of equipment DOES NOT
break the connection from the mains.
MAINS DISCONNECT: The plug shall remain
readily operable. For rack-mount or installation
where plug is not accessible, an all-pole mains
switch with a contact separation of at least 3
mm in each pole shall be incorporated into the
electrical installation of the rack or building.
FOR UNITS EQUIPPED WITH EXTERNALLY
ACCESSIBLE FUSE RECEPTACLE: Replace fuse
with same type and rating only.
MULTIPLE-INPUT VOLTAGE: This equipment
may require the use of a different line cord,
attachment plug, or both, depending on the available power source at installation. Connect this
equipment only to the power source indicated
on the equipment rear panel. To reduce the risk
of fire or electric shock, refer servicing to qualified service personnel or equivalent.
IMPORTANT SAFETY INSTRUCTIONS
If you want to dispose this product, do not mix it with general household w aste. There is a
separate collection system for used electronic products in accordance with legislation that
requires proper treatment, recovery and recycling.
Private household in the 25 member states of the EU, in Switzerland and Norway may return their used
electronic products free of charge to designated collection facilities or to a retailer (if you purchase a similar
new one).
For Countries not mentioned above, please contact your local authorities for a correct method of disposal.
By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and
recycling and thus prevent potential negative effects on the environment and human health.
DECLARATION OF CONFORMITY
Manufacturer’s Name: Lexicon
®
Manufacturer’s Address: 8760 S. Sandy Parkway
Sandy, Utah 84070, USA
declares that the product:
Product name: I•ONIX FW810s
Note: Product name may be suffixed by the letters EU.
Product option: None
conforms to the following Product Specifications:
Safety: IEC 60065-01 + Amd. 1
EMC: EN 55013 (2001+A1)
EN 55020 (1998)
Supplementary Information:
The product herewith complies with the requirements of the Low Voltage Directive 2006/95/EC
and the EMC Directive 2004/108/EC.
Vice President of Engineering
8760 S. Sandy Parkway
Sandy, Utah 84070, USA
Date: October 24, 2008
European Contact: Your local Lexicon Sales and Service Office or
Harman Music Group
8760 South Sandy Parkway
Sandy, Utah 84070, USA
Ph: (801) 566-8800
Fax: (801) 566-7005
ELECTROMAGNETIC
COMPATIBILITY
This unit conforms to the Product Specifications noted
on the Declaration of Conformity. Operation is
subject to the following two conditions:
•
this device may not cause harmful
interference, and
•
this device must accept any interference received,
including interference that may cause undesired
operation.
Operation of this unit within significant
electromagnetic fields should be avoided.
•
use only shielded interconnecting cables.
U.K. MAINS PLUG WARNING
A molded mains plug that has been cut off
from the cord us unsafe. Discard the mains plug
at a suitable disposal facility. NEVER UNDER
ANY CIRCUMSTANCES SHOULD YOU INSERT A
DAMAGED OR CUT MAINS PLUG INTO A 13 AMP
POWER SOCKET. Do not use the mains plug
without the fuse cover in place. Replaceent fuse
covers can be obtained from your local retailer.
Replacement fuses are 13 amps and MUST be
ASTA approved to BS1362.
Service Info
If you require technical support, contact Lexicon® Professional Customer Service.
Be prepared to accurately describe the problem. Know the serial number of your unit,
found on a sticker attached to the bottom of the I-ONIX FW810S. If you have not
already taken the time to fill out your warranty registration card and send it in, please do
so now.
Before you return a product to the factory for service, we recommend you refer to
the manual. Make sure you have correctly followed installation steps and operation
procedures. If you are still unable to solve a problem, contact our Customer Service
Department at (801) 568-7660 for consultation. If you need to return a product
to the factory for service, you MUST contact Customer Service to obtain a Return
Authorization Number. No returned products will be accepted at the factory without a
Return Authorization Number. Please refer to the Warranty information on the following page, which extends to the first end-user. After expiration of the warranty, a reasonable charge will be made for parts, labor, and packing if you choose to use the factory
service facility. In all cases, you are responsible for transportation charges to the factory.
Lexicon Professional will pay return shipping if the unit is still under warranty.
Use the original packing material if it is available. Mark the package with the name
of the shipper and with these words in red: DELICATE INSTRUMENT, FRAGILE!
Insure the package properly. Ship prepaid, not collect. Do not ship parcel post.
Warranty
This warranty is valid only for the original purchaser and only in the United States.
The warranty registration card that accompanies this product must be mailed (or 1.
online regisration must be completed at www.lexiconpro.com) within 30 days after
purchase date to validate this warranty. Proof-of-purchase is considered to be the
burden of the consumer.
Lexicon Professional warrants this product, when bought and used solely within 2.
the U.S., to be free from defects in materials and workmanship under normal use
and service.
Lexicon Professional’s liability under this warranty is limited to repairing or, 3.
at our discretion, replacing defective materials that show evidence of defect,
provided the product is returned to Lexicon Professional WITH RETURN
AUTHORIZATION from the factory, where all parts and labor will be covered
up to a period of 1 year. A Return Authorization number must be obtained from
Lexicon Professional by telephone. The company shall not be liable for any consequential damage as a result of the product’s use in any circuit or assembly.
Lexicon Professional reserves the right to make changes in design or make addi-4.
tions to or improvements upon this product without incurring any obligation to
install the same additions or improvements on products previously manufactured.
The foregoing is in lieu of all other warranties, expressed or implied, and Lexicon 5.
Professional neither assumes nor authorizes any person to assume on its behalf any
obligation or liability in connection with the sale of this product. In no event shall
Lexicon Professional or its dealers be liable for special or consequential damages or
from any delay in the performance of this warranty due to causes beyond its control.
Table of Contents
INtRodUctIoN ................................................................... 1
Features ......................................................................... 1
Unpacking the Ionix FW810S....................................... 2
The following items are included: ...................................2
System Requirements ....................................................2
FRoNt PANeL ...................................................................... 3
ReAR PANeL ........................................................................ 5
coNNectING the I-oNIX FW810S ...................................... 7
Microphones ................................................................. 7
Line Level Sources ......................................................... 7
Instruments ................................................................... 7
Computer/Digital Audio Workstation (DAW) .............. 7
Headphones .................................................................. 7
Monitor Speakers .......................................................... 7
Example Rear Panel Connections .................................. 8
Example Rear Panel Connections .................................. 8
the I-oNIX FW810S MIXeR - oveRvIeW ............................. 9
Installation .................................................................... 9
The Mixer – Input 1-8 Strips ..........................................10
Monitor Reverbs ............................................................. 11
The Mixer - Balanced Out (Aux Out) Controls ............. 12
The Mixer – Master Faders ............................................. 12
Channel Strip Dynamics ................................................13
Channel Strip Dynamics – Gate ..................................... 14
Channel Strip Dynamics – Compressor .......................... 14
Channel Strip Dynamics – Limiter .................................15
Channel Strip Dynamics – Gain Fader ........................... 16
EQ .................................................................................. 16
File Menu........................................................................17
Ionix FW810S Control Panel .........................................18
SPecIFIcAtIoNS .................................................................. 19
6
Introduction
Congratulations and thank you for purchasing the Lexicon® I-ONIX
FW810S!
With a wealth of features – including dbx® high-voltage, ultra low noise mic
pre’s, Pantheon II reverbs, and a powerful hardware mixing board with dbx
dynamics and hardware monitor reverb – the Lexicon I•ONIX FW810S is
more than just an 10-in, 12-out FireWireTM audio interface. It’s a pro recording studio contained in a single rack unit.
The high-voltage, ultra low noise dbx mic pre’s on every channel provide optimal timbre and tonality on every track. And the newly updated
Pantheon II plug-in provides smooth, lush Lexicon reverbs for creating ideal
sonic spaces.
With built-in dbx Type IVTM conversion, your digital recordings will preserve their dynamic range even when levels get too high. They’ll acquire that
forgiving, oversaturated quality once only found on big analog recorders.
conversion actually gives you more headroom, capturing subtle details in
higher level signals instead of hard clipping them.
Plus, the Lexicon I•ONIX FW810S adds a powerful hardware Mixer with
integrated dbx dynamics (compresser, gate, limiter, EQ) to your digital audio
workstation. The Mixer’s true-to-life interface design feels familiar from the
second you start it, making it easy to adjust levels, route signals through 10
inputs and 12 outputs, and apply and preview reverbs and dynamics. And
the I•ONIX FW810S does the processing, so you can mix and fine tune
your recordings in real time with zero latency. You can even save and load
snapshots of mixer settings. Create up to five unique monitor mixes or mix
7.1 surround projects. Or assign the I•ONIX FW810S to start up with a
snapshot.
With so many powerful and useful recording studio tools, it’s more than just
a FireWire interface. It’s the Lexicon I•ONIX FW810S.
Features
dbx high-voltage, ultra low noise mic pre’s on all 8 channels •
dbx dynamics (compressor, limiter, gate, EQ) on all 8 channels •
6 analog combi-jack inputs on the rear panel for mic/line inputs •
2 front panel combi-jacks accept mic, line, or instrument signals •
Type IV conversion feature emulates tape saturation at high levels •
Zero latency hardware mixer with dbx dynamics and hardware monitor •
reverb
44.1 to 96KHz sample rates, 24 bit processing •
8 analog TRS outputs (7.1 surround capable) and stereo main (control •
room) outs
1
Stereo S/PDIF digital I/O •
MIDI In and Out •
FireWire 400 connection to DAW •
Software suite includes Steinberg’s Cubase LE 4, Toontrack EZ •
Drummer lite, and Lexicon® Pantheon II reverb plug-in
Unpacking the Ionix FW810S
The Ionix FW810S is shipped in one carton, containing the Ionix FW810S
unit and a software DVD for Windows® and Macintosh® systems. After
unpacking, save all the packaging materials in case you ever have to ship the
unit. Thoroughly inspect the Ionix FW810S and packing materials for signs
of damage. Report any shipment damage to the carrier that delivered the
product or dealer from whom you purchased the product at once.
THE FOLLOWING ITEMS ARE INCLUDED:
Ionix FW810S•
Installer DVD containing FireWire•
ware, the Lexicon Pantheon II reverb plug-in, Cubase LE 4 Recording
Software, and ToonTrack EZ Drummer Lite for Mac® and Windows®
FireWire Connector Cable•
This Owner’s Manual •
Lexicon Professional warranty registration•
TM
drivers, the FW810S Mixer soft-
NOTE: The full Cubase LE 4 manual and the FW810S Tutorial are located
on the software DVD.
System Requirements
Powerful software for audio recording requires a powerful computer with
the right operating system software, processor and memory. Most computers currently sold already meet these requirements, or can be upgraded to be
compatible with the Lexicon I-ONIX FW810S. As with all such systems,
adding more RAM than the minimum will allow you to do more processing
and improve performance.
®
Windows
Mac
Vista, XP
Multicore system•
1GB RAM (Recommended)•
Display Resolution 1024 x 768 pixels•
DVD-ROM drive•
Internet access required for software license activation•
®
®
Intel•
Multicore system
1 GB RAM (Recommended)•
OS X Version 10.4.9 or higher•
Display Resolution 1024 x 768 pixels•
DVD-ROM drive•
Internet access required for software license activation•
2
Note: Adobe Reader is required to view the pdf documents on the DVD.
Front Panel
1
3
2
8
4
1 0 1 1
7
9
6
5
1. INPUTS 1 AND 2 (MIC/INST 1 AND MIC/INST 2)
These balanced inputs accept XLR or 1/4” connectors, and support mic,
line, and instrument level sources (including guitars).
2. INSTRUMENT BUTTON/LED
Press when an instrument level source (such as a guitar) is connected to the
corresponding input (1 or 2). The button illuminates when activated.
3. +48V BUTTON/LED
Each of these buttons enables the phantom power to the corresponding
inputs pairs. Dynamic microphones do not require phantom power to
operate, but are not harmed by it. Most condenser microphones do require
phantom power to operate. If you are unsure about the phantom power
requirements for your microphone, consult your microphone’s documentation or contact the manufacturer. This switch should be OFF if you are
connecting any line-level source to the Mic/Inst or Mic Pre jacks.
4. DYNAMICS LEDS AND INPUT LEVEL LEDS
The top three rows indicate what dynamics are active for each input. The
bottom three rows indicate signal presence (green) and level (yellow and
red) for each input.
5. FIREWIRETM LED
Indicates when a FireWireTM connection is present.
6. POWER LED
Indicates when the I-ONIX FW810S is turned on.
7. GAIN KNOBS 1 AND 2
These knobs adjust the input gain levels for Mic/Inst 1 and Mic/Inst 2.
8. GAIN KNOBS 3 – 8
These knobs adjust the input gain levels for Mic Pre 3 – 8 (the inputs
located on the back panel).
9. HEADPHONE OUTPUT JACK
Connect headphones here.
10. HEADPHONE LEVEL KNOB
Adjust headphone output signal level here.
11. MAIN OUTPUTS LEVEL KNOB
Adjust the main output signal level here.
3
Loading...