La Crosse Technology WS9117 User Manual
868 MHz TEMPERATURE STATION
Instruction Manual
INTRODUCTION:
Congratulations on purchasing this innovative 868MHz Temperature
Station which displays time, indoor temperature and up to three outdoor
temperature readings. To enjoy the full benefits of this innovative product,
please read this operating manual.
44
« Instant Transmission+» is the up and coming state-of-the-art
new wireless transmission technology, exclusively designed and
developed by LA CROSSE TECHNOLOGY.
“IT +” offers you an immediate update of all your outdoor data
measured from the transmitters: follow your climatic variations
in real-time!
45
TEMPERATURE STATION:
SET/CH key
MIN/MAX/+
key
Hanging hole
Battery
compartment
Detachable
stand
46
TEMPERATURE TRANSMITTER:
47
FEATURES:
• LCD clock in 12 or 24 hour time display
• Indoor and outdoor temperature reading in degrees Celsius or
Fahrenheit
• Can receive up to three Outdoor transmitters
• Indoor and outdoor temperature with Minimum and Maximum
records
• Wireless transmission at 868 MHz
• Signal reception intervals at 4 seconds
• Table standing or wall mountable (detachable table stand)
48
SETTING UP:
WHEN ONE TRANSMITTER IS USED
1. First, insert the batteries in the transmitter (see “How to install
and replace batteries in the Temperature transmitter” below).
2. Within 2 minutes of powering up the transmitter, insert the
batteries in the Temperature Station (see “How to install and
replace batteries in the Temperature station” below). Once the
batteries are in place, all segments of the LCD will light up briefly.
Following the indoor temperature and the time as 0:00 will be
displayed. If these informations are not displayed on the LCD
after 60 seconds, remove the batteries and wait for at least 60
49
seconds before reinserting them. Once the indoor data is
displayed user may proceed to the next step.
3. Afte r the batteries are inserted, the Temperature Station will start
receiving data signal from the transmitter. The outdoor
temperature should then be displayed on the Temperature station.
If this does not happen after 2 minutes, the batteries will need to
be removed from both units and reset from step 1.
4. In order to ensure sufficient 868 MHz transmission however, the
distance between the Temperature Station and the transmitter
should not be more than 100 meters (see notes on “Positioning”
and “868 MHz Reception”).
50
WHEN MORE THAN ONE TRANSMITTER IS USED
1. User shall remove all the batteries from the Temperatuire Station
and transmitters and wait 60 seconds.
2. Insert the batteries in the first transmitter .
3. Within 2 minutes of powering up the first transmitter, insert the
batteries in the Temperature Station. Once the batteries are in
place, all segments of the LCD will light up briefly. Following the
indoor temperature and the time as 0:00 will be displayed. If these
informations are not displayed on the LCD after 60 seconds,
remove the batteries from both units and wait for at least 60
seconds before reinserting them.
4. The outdoor temperature from the first transmitter (channel 1)
51
should then be displayed on the Temperature Station. Also, the
signal reception icon will be displayed. If this does not happen after
2 minutes, the batteries will need to be removed from both units
and reset from step 1.
5. Insert the batteries in the second transmitter as soon as the outdoor
temperature reading from the first transmitter are displayed on the
Temperature Station.
Note : User shall insert the batteries into the second transmitter within 45
seconds after the Temperature Station displays the information of the first
transmitter.
52
6. The outdoor temperature from the second transmitter and the
"channel 2" icon should then be displayed on the Temperature
Station. If this does not happen after 2 minutes, the batteries will
need to be removed from all the units and reset from step 1.
7. Insert the batteries in the third transmitter as soon as the "channel
2" icon and outdoor data are displayed on the Temperature Station.
Then within 2 minutes, the channel 3 outdoor data from the third
transmitter will be displayed and the channel icon will shift back to
"1" once the third transmitter is successfully received. If this is not
happen, user shall restart the setting up from step 1.
Note : User shall insert the batteries into the third transmitter within 45
53
seconds after the Temperature Station displays the information of the
second transmitter.
8. In order to ensure sufficient 868 MHz transmission however, the
distance between the Temperature Station and the transmitter
should not be more than 100 meters (see notes on “Positioning”
and “868 MHz Reception”).
54
HOW TO INSTALL AND REPLACE BATTERIES IN THE
TEMPERATURE STATION
The Temperature Station uses 2 x AAA, IEC LR3, 1.5V batteries.
When batteries will need to be replaced, the low battery icon will
appear on the LCD. To install and replace the batteries, please
follow the steps below :
55
1. Lift up the battery compartment
cover.
2. Insert batteries observing the
correct polarity (see marking).
3. Replace compartment cover.
56
Loading...