Kyocera FS-C2026, FS-2126MFP Service Manual [UK ]

FS-C2026MFP+ FS-C2126MFP+

SERVICE

MANUAL

Published in April 2011

842MB110 2MBSM060 First Edition

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

It may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste officials for details in your area for proper disposal.

ATTENTION

IL Y A UN RISQUE D’EXPLOSION SI LA BATTERIE EST REMPLACEE PAR UN MODELE DE TYPE INCORRECT. METTRE AU REBUT LES BATTERIES UTILISEES SELON LES INSTRUCTIONS DONNEES.

Il peut être illégal de jeter les batteries dans des eaux d’égout municipales. Vérifiez avec les fonctionnaires municipaux de votre région pour les détails concernant des déchets solides et une mise au rebut appropriée.

Revision history

Revision Date Replaced pages Remarks

This page is intentionally left blank.

Safety precautions

This booklet provides safety warnings and precautions for our service personnel to ensure the safety of their customers, their machines as well as themselves during maintenance activities. Service personnel are advised to read this booklet carefully to familiarize themselves with the warnings and precautions described here before engaging in maintenance activities.

Safety warnings and precautions

Various symbols are used to protect our service personnel and customers from physical danger and to prevent damage to their property. These symbols are described below:

DANGER: High risk of serious bodily injury or death may result from insufficient attention to or incorrect

compliance with warning messages using this symbol.

WARNING: Serious bodily injury or death may result from insufficient attention to or incorrect compliance

with warning messages using this symbol.

CAUTION: Bodily injury or damage to property may result from insufficient attention to or incorrect com-

pliance with warning messages using this symbol.

Symbols

The triangle ( ) symbol indicates a warning including danger and caution. The specific point of attention is

shown inside the symbol.

General warning. Warning of risk of electric shock.

Warning of high temperature.

indicates a prohibited action. The specific prohibition is shown inside the symbol.

General prohibited action. Disassembly prohibited.

indicates that action is required. The specific action required is shown inside the symbol.

General action required. Remove the power plug from the wall outlet.

Always ground the copier.

1. Installation Precautions

WARNING

• Do not use a power supply with a voltage other than that specified. Avoid multiple connections to one outlet: they may cause fire or electric shock. When using an extension cable, always check that

it is adequate for the rated current. .....................................................................................................

• Connect the ground wire to a suitable grounding point. Not grounding the copier may cause fire or electric shock. Connecting the earth wire to an object not approved for the purpose may cause explosion or electric shock. Never connect the ground cable to any of the following: gas pipes, lightning rods, ground cables for telephone lines and water pipes or faucets not approved by the proper

authorities. ..........................................................................................................................................

CAUTION:

• Do not place the copier on an infirm or angled surface: the copier may tip over, causing injury. .........

• Do not install the copier in a humid or dusty place. This may cause fire or electric shock. .................

• Do not install the copier near a radiator, heater, other heat source or near flammable material. This

may cause fire. ...................................................................................................................................

• Allow sufficient space around the copier to allow the ventilation grills to keep the machine as cool

as possible. Insufficient ventilation may cause heat buildup and poor copying performance. ............

• Always handle the machine by the correct locations when moving it. .................................................

• Always use anti-toppling and locking devices on copiers so equipped. Failure to do this may cause

the copier to move unexpectedly or topple, leading to injury. ..............................................................

• Avoid inhaling toner or developer excessively. Protect the eyes. If toner or developer is accidentally ingested, drink a lot of water to dilute it in the stomach and obtain medical attention immediately. If it gets into the eyes, rinse immediately with copious amounts of water and obtain medical atten-

tion. .....................................................................................................................................................

• Advice customers that they must always follow the safety warnings and precautions in the copier’s

instruction handbook. .........................................................................................................................

2. Precautions for Maintenance

WARNING

• Always remove the power plug from the wall outlet before starting machine disassembly. ................

• Always follow the procedures for maintenance described in the service manual and other related

brochures. ..........................................................................................................................................

• Under no circumstances attempt to bypass or disable safety features including safety mechanisms

and protective circuits. ........................................................................................................................

• Always use parts having the correct specifications. ............................................................................

• Always use the thermostat or thermal fuse specified in the service manual or other related brochure when replacing them. Using a piece of wire, for example, could lead to fire or other serious acci-

dent. ...................................................................................................................................................

• When the service manual or other serious brochure specifies a distance or gap for installation of a

part, always use the correct scale and measure carefully. ..................................................................

• Always check that the copier is correctly connected to an outlet with a ground connection. ...............

• Check that the power cable covering is free of damage. Check that the power plug is dust-free. If it

is dirty, clean it to remove the risk of fire or electric shock. .................................................................

• Never attempt to disassemble the optical unit in machines using lasers. Leaking laser light may

damage eyesight. ...............................................................................................................................

• Handle the charger sections with care. They are charged to high potentials and may cause electric

shock if handled improperly. ...............................................................................................................

CAUTION

• Wear safe clothing. If wearing loose clothing or accessories such as ties, make sure they are safely

secured so they will not be caught in rotating sections. ......................................................................

• Use utmost caution when working on a powered machine. Keep away from chains and belts. ..........

• Handle the fixing section with care to avoid burns as it can be extremely hot. ..................................

• Check that the fixing unit thermistor, heat and press rollers are clean. Dirt on them can cause

abnormally high temperatures. ...........................................................................................................

• Do not remove the ozone filter, if any, from the copier except for routine replacement. ......................

• Do not pull on the AC power cord or connector wires on high-voltage components when removing

them; always hold the plug itself. ........................................................................................................

• Do not route the power cable where it may be stood on or trapped. If necessary, protect it with a

cable cover or other appropriate item. ................................................................................................

• Treat the ends of the wire carefully when installing a new charger wire to avoid electric leaks. ..........

• Remove toner completely from electronic components. .....................................................................

• Run wire harnesses carefully so that wires will not be trapped or damaged. ......................................

• After maintenance, always check that all the parts, screws, connectors and wires that were removed, have been refitted correctly. Special attention should be paid to any forgotten connector,

trapped wire and missing screws. .......................................................................................................

• Check that all the caution labels that should be present on the machine according to the instruction

handbook are clean and not peeling. Replace with new ones if necessary. .......................................

• Handle greases and solvents with care by following the instructions below: ......................................

· Use only a small amount of solvent at a time, being careful not to spill. Wipe spills off completely.

· Ventilate the room well while using grease or solvents.

· Allow applied solvents to evaporate completely before refitting the covers or turning the power switch on.

· Always wash hands afterwards.

• Never dispose of toner or toner bottles in fire. Toner may cause sparks when exposed directly to

fire in a furnace, etc. ...........................................................................................................................

• Should smoke be seen coming from the copier, remove the power plug from the wall outlet immedi-

ately. ...................................................................................................................................................

3. Miscellaneous

WARNING

• Never attempt to heat the drum or expose it to any organic solvents such as alcohol, other than the

specified refiner; it may generate toxic gas. ........................................................................................

• Keep the machine away from flammable liquids, gases, and aerosols. A fire or an electric shock

might occur. ........................................................................................................................................

This page is intentionally left blank.

1-1 Specifications

1-1-1 Specifications ........................................................................................................................ 1-1-1

1-1-2 Parts names .......................................................................................................................... 1-1-6

(1) Machine (front side)..........................................................................................................1-1-6

(2) Machine (rear side)........................................................................................................... 1-1-7

(3) Document processor ........................................................................................................ 1-1-8

(4) Operation panel ................................................................................................................1-1-9

1-1-3 Machine cross section ......................................................................................................... 1-1-10

1-2 Installation

1-2-1 Installation environment......................................................................................................... 1-2-1

1-2-2 Unpacking.............................................................................................................................. 1-2-2

1-2-3 Installing the expansion memory (option) ............................................................................ 1-2-12

1-3 Maintenance Mode

1-3-1 Maintenance mode ................................................................................................................ 1-3-1

(1) Executing a maintenance item ......................................................................................... 1-3-1

(2) Maintenance modes item list ............................................................................................ 1-3-2

(3) Contents of the maintenance mode items ........................................................................ 1-3-5

1-3-2 Service mode....................................................................................................................... 1-3-57

(1) Executing a service mode .............................................................................................. 1-3-57

(2) Description of service mode ........................................................................................... 1-3-58

2MA/2MB

1-4 Troubleshooting

1-4-1 Paper misfeed detection ........................................................................................................ 1-4-1

(1) Paper misfeed indication .................................................................................................. 1-4-1

(2) Paper misfeed detection condition ................................................................................... 1-4-2

1-4-2 Self-diagnostic function ......................................................................................................... 1-4-6

(1) Self-diagnostic function .................................................................................................... 1-4-6

(2) Self diagnostic codes........................................................................................................ 1-4-7

1-4-3 Image formation problems ................................................................................................... 1-4-28

(1) No image appears (entirely white).................................................................................. 1-4-29

(2) No image appears (entirely black).................................................................................. 1-4-29

(3) A specific color is printed solid. ...................................................................................... 1-4-30

(4) The back side gets dirty.................................................................................................. 1-4-30

(5) Image is too light. ........................................................................................................... 1-4-30

(6) The background is colored. ............................................................................................ 1-4-31

(7) White streaks are printed vertically................................................................................. 1-4-31

(8) Black streaks are printed vertically. ................................................................................ 1-4-31

(9) Streaks are printed horizontally. ..................................................................................... 1-4-32

(10) Spots are printed. ........................................................................................................... 1-4-32

(11) The leading edge of image begins to print too early or too late...................................... 1-4-32

(12) Paper is wrinkled. ........................................................................................................... 1-4-32

(13) Offset occurs. ................................................................................................................. 1-4-33

(14) Part of image is missing. ................................................................................................ 1-4-33

(15) Fusing is loose................................................................................................................ 1-4-33

(16) Colors are printed offset to each other. .......................................................................... 1-4-34

1-4-4 Electric problems ................................................................................................................. 1-4-35

1-4-5 Mechanical problems........................................................................................................... 1-4-40

2MA/2MB

1-4-6 Send error code ................................................................................................................... 1-4-42

(1) Scan to SMB error codes ............................................................................................... 1-4-42

(2) Scan to FTP error codes ................................................................................................ 1-4-43

(3) Scan to E-mail error codes ............................................................................................. 1-4-44

1-4-7 Error codes .......................................................................................................................... 1-4-45

(1) Error code.......................................................................................................................1-4-45

(2) Table of general classification ........................................................................................ 1-4-46

(2-1) U004XX error code table: Interrupted phase B ..................................................... 1-4-48

(2-2) U006XX error code table: Problems with the unit ................................................. 1-4-48

(2-3) U008XX error code table: Page transmission error............................................... 1-4-48

(2-4) U009XX error code table: Page reception error .................................................... 1-4-48

(2-5) U010XX error code table: G3 transmission ........................................................... 1-4-49

(2-6) U011XX error code table: G3 reception ................................................................ 1-4-50

(2-7) U017XX error code table: V.34 transmission ........................................................ 1-4-51

(2-8) U018XX error code table: V.34 reception.............................................................. 1-4-51

1-5 Assembly and disassembly

1-5-1 Precautions for assembly and disassembly........................................................................... 1-5-1

(1) Precautions....................................................................................................................... 1-5-1

(2) Drum................................................................................................................................. 1-5-1

(3) Toner ................................................................................................................................ 1-5-1

(4) How to tell a genuine Kyocera Mita toner container ......................................................... 1-5-2

1-5-2 Outer covers .......................................................................................................................... 1-5-3

(1) Detaching and refitting the rear upper cover, right upper cover,

left upper cover and front cover ....................................................................................... 1-5-3

(2) Detaching and refitting the right rear cover, right cover and right lower cover .................1-5-6

(3) Detaching and refitting the left rear cover, left cover and left lower cover ........................ 1-5-9

(4) Detaching and refitting the inner cover........................................................................... 1-5-11

1-5-3 Paper feed section............................................................................................................... 1-5-13

(1) Detaching and refitting the retard roller unit ................................................................... 1-5-13

(2) Detaching and refitting the paper feed roller unit............................................................ 1-5-15

(3) Detaching and refitting the MP paper feed roller ............................................................ 1-5-17

1-5-4 Developing section .............................................................................................................. 1-5-19

(1) Detaching and refitting the developing unit .................................................................... 1-5-19

1-5-5 Drum section ....................................................................................................................... 1-5-21

(1) Detaching and refitting the drum unit.............................................................................. 1-5-21

1-5-6 Transfer/Separation section ................................................................................................ 1-5-22

(1) Detaching and refitting the intermediate transfer unit..................................................... 1-5-22

(2) Detaching and refitting the transfer roller unit................................................................. 1-5-25

1-5-7 Fuser section ....................................................................................................................... 1-5-26

(1) Detaching and refitting the fuser unit.............................................................................. 1-5-26

1-5-8 PWBs................................................................................................................................... 1-5-27

(1) Detaching and refitting the engine PWB......................................................................... 1-5-27

(2) Detaching and refitting the power source PWB.............................................................. 1-5-29

(3) Detaching and refitting the main PWB............................................................................ 1-5-30

(4) Detaching and refitting the high voltage PWB ................................................................ 1-5-35

(5) Detaching and refitting the FAX control PWB (4 in 1 model (with FAX) only) ................ 1-5-36

1-5-9 Drive section........................................................................................................................ 1-5-37

(1) Detaching and refitting the MP feed drive unit................................................................ 1-5-37

(2) Detaching and refitting the drum/developing drive unit .................................................. 1-5-38

(3) Detaching and refitting the paper feed drive unit............................................................ 1-5-40

(4) Detaching and refitting the fuser pressure drive unit ...................................................... 1-5-41

(5) Detaching and refitting the middle transfer drive unit ..................................................... 1-5-43

2MA/2MB

1-5-10 Optical section ..................................................................................................................... 1-5-45

(1) Detaching and refitting the laser scanner unit ................................................................ 1-5-45

(2) Detaching and refitting the scanner unit ......................................................................... 1-5-48

1-5-11 Document processor ........................................................................................................... 1-5-52

(1) Detaching and refitting the document processor ............................................................ 1-5-52

(2) Detaching and refitting the DP paper feed pulley unit .................................................... 1-5-56

(3) Detaching and refitting the DP separation pad............................................................... 1-5-60

(4) Detaching and refitting the DP drive PWB...................................................................... 1-5-61

1-5-12 Others .................................................................................................................................. 1-5-62

(1) Detaching and refitting the paper conveying unit ........................................................... 1-5-62

(2) Detaching and refitting the operation panel.................................................................... 1-5-64

(3) Detaching and refitting the power source inlet ............................................................... 1-5-65

(4) Direction of installing the principal fan motors ................................................................ 1-5-67

1-6 Requirements on PWB Replacement

1-6-1 Upgrading the firmware ......................................................................................................... 1-6-1

1-6-2 Remarks on engine PWB replacement ................................................................................. 1-6-2

2-1 Mechanical Construction

2-1-1 Paper feed/conveying section ............................................................................................... 2-1-1

(1) Cassette paper feed section............................................................................................. 2-1-1

(2) MP tray paper feed section............................................................................................... 2-1-3

(3) Paper conveying section .................................................................................................. 2-1-5

2-1-2 Drum section ......................................................................................................................... 2-1-7

2-1-3 Developing section ................................................................................................................ 2-1-9

2-1-4 Optical section ..................................................................................................................... 2-1-11

(1) Image scanner section ................................................................................................... 2-1-11

(2) Laser scanner section .................................................................................................... 2-1-14

2-1-5 Transfer/Separation section ................................................................................................ 2-1-16

(1) Intermediate transfer unit section ................................................................................... 2-1-16

(2) Secondary transfer roller section.................................................................................... 2-1-18

2-1-6 Fuser section ....................................................................................................................... 2-1-19

2-1-7 Eject/Feedshift section ........................................................................................................ 2-1-21

2-1-8 Duplex conveying section....................................................................................................2-1-23

2-1-9 Document processor ........................................................................................................... 2-1-25

(1) Original feed section....................................................................................................... 2-1-25

(2) Original conveying section.............................................................................................. 2-1-27

(3) Original switchback/eject sections .................................................................................. 2-1-29

2-2 Electrical Parts Layout

2-2-1 Electrical parts layout ............................................................................................................ 2-2-1

(1) PWBs................................................................................................................................ 2-2-1

(2) Switches and sensors....................................................................................................... 2-2-4

(3) Motors............................................................................................................................... 2-2-6

(4) Others............................................................................................................................... 2-2-8

(5) Document processor ........................................................................................................ 2-2-9

2-3 Operation of the PWBs

2-3-1 Power source PWB ............................................................................................................... 2-3-1

2-3-2 Engine PWB .......................................................................................................................... 2-3-3

2-3-3 Main PWB............................................................................................................................ 2-3-13

2-3-4 Drum relay PWB .................................................................................................................. 2-3-20

2-3-5 DP drive PWB...................................................................................................................... 2-3-23

2-4 Appendixes

2-4-1 Appendixes ............................................................................................................................ 2-4-1

(1) Maintenance kits............................................................................................................... 2-4-1

(2) Repetitive defects gauge .................................................................................................. 2-4-2

(3) Firmware environment commands ................................................................................... 2-4-3

(4) Wiring diagram ................................................................................................................. 2-4-9

2MA/2MB

1-1 Specifications

1-1-1 Specifications

Machine

2MA/2MB

Item

Specifications

3 in 1 model (without FAX) 4 in 1 model (with FAX)

Type Desktop

Printing method Electrophotography by semiconductor laser, tandem (4) drum system

Originals Sheet, Book, 3-dimensional objects (maximum original size: Folio/Legal)

Original feed system Fixed

(Duplex: 60 to 163 g/m2)

, 230 m (Cardstock)

Paper weight

Paper type

Cassette 60 to 163 g/m

MP tray

Cassette

60 to 220 g/m

Plain, Recycled, Preprinted, Bond, Color (Colour), Prepunched, Letterhead, Thick, High quality, Custom 1 to 8 (Duplex: Same as simplex)

Plain, Transparency, Vellum, Labels, Recycled, Preprinted, Bond,

MP tray

Cardstock, Color (Colour), Prepunched, Letterhead, Thick, Envelope, Coated, High quality, Custom 1 to 8

Cassette

Paper size

MP tray

A4, A5, A6, B5, Letter, Legal, Statement, Executive, Oficio II, Folio, 16K, Custom

A4, A5, A6, B5, ISO B5, B6, Letter, Legal, Statement, Executive, Oficio II, Folio, 16K, Envelope #10, Envelope #9, Envelope #6, Envelope Monarch, Envelope DL, Envelope C5, Postcards, Return postcard, Youkei 2, Youkei 4, Custom

Manual mode : 25 to 400%, 1% increments

Zoom level

Auto mode : 400%, 200%, 141%, 129%, 115%, 90%, 86%, 78%, 70%,

A4R : 26 sheets/min LetterR : 28 sheets/min

Simplex

Copying

speed

Legal : 23 sheets/min B5R : 28 sheets/min A5R : 28 sheets/min A6R : 28 sheets/min

A4R : 13 sheets/min

Duplex

LetterR : 13 sheets/min Legal : 12 sheets/min

First copy

time

(A4, feed from

cassette)

Warm-up time

(22 °C/71.6 °F, 60% RH)

Paper

Cassette 150 sheets (80g/m

capacity

B/W

Color

MP tray 50 sheets (80 g/m

When using the DP : 11.0 s or less When the DP is not used: 10.0 s or less

When using the DP : 13.0 s or less When the DP is not used: 12.0 s or less

Power on : 29 s or less Sleep mode: 20 s or less

Output tray capacity 250 sheets (80g/m

64%, 50%, 25%

)

, plain paper, A4/Letter or less)

)

Continuous copying 1 to 999 sheets

1-1-1

2MA/2MB

Item

Light source LED

Scanning system Flat bed scanning by CCD image sensor

Photoconductor OPC drum (diameter 30 mm)

Image write system Semiconductor laser

Charging system Charger roller

Developing system

Transfer system

Separation system Small diameter separation

Cleaning system Drum: Counter blade

Charge erasing system Exposure by cleaning lamp (LED)

Fusing system

3 in 1 model (without FAX) 4 in 1 model (with FAX)

Touch down developing system Developer: 2-component Toner replenishing: Automatic from the toner container

Primary: Transfer belt Secondary: Transfer roller

Heat and pressure fusing with the heat roller and the press roller Heat source: halogen heater Abnormally high temperature protection devices: thermostat

Specifications

CPU PowerPC464 (667MHz)

Main

memory

Interface

Resolution 600 × 600 dpi

Operating

environment

Dimensions (W × D × H)

Weight

Space required (W × D)

Standard 768 MB

Maximum 1792 MB

Standard

Option

Temperature 10 to 32.5 °C/50 to 90.5 °F

Humidity 15 to 80% RH

Altitude 2,500 m/8,202 ft or less

Brightness 1,500 lux or less

USB interface connector: 1 (USB Hi-speed) USB host: 2 Network interface: 1 (10BASE-T/100BASE-TX)

KUIO/W slot: 1

514 × 550 × 580 mm 20 1/4 × 21 5/8 × 22 13/16”

36.5 kg / 80.3 lb (with toner container)

514 × 1020 mm (using MP tray) 20 1/4 × 40 3/16” (using MP tray)

Power source

Options Paper feeder × 2, Expanded memory

120 V AC, 60 Hz, more than 8.9 A 220 - 240 V AC, 50/60 Hz, more than 4.7 A

1-1-2

Document processor

Item Specifications

Original feed method Automatic feed

Supported original types Sheet originals

2MA/2MB

Original sizes

Original weights

Maximum: A4/Legal Minimum : A5/Statement

Simplex: 50 to 120 g/m Duplex : 50 to 110 g/m

Loading capacity 50 sheets (50 to 80 g/m2) or less

Dimensions (W × D × H)

490 × 338 × 104 mm 19 5/16 × 13 5/16 × 4 1/8”

Weight 3 kg/ 6.6 lb or less

Printer

Item Specifications

Printing speed Same as copying speed.

First print time

(A4, feed from cassette)

Resolution 600 dpi

Operating system

B/W : 9.0 s or less Color: 10.5 s or less

Windows 2000, Windows XP, Windows XP Professional, Windows Server 2003, Windows Server 2003 x64 Edition, Windows Vista x86 Edition, Windows Vista x64 Edition, Windows 7 x86 Edition, Windows 7 x64 Edition, Windows Server 2008, Windows Server 2008 x64 Edition, Apple Macintosh OS 10.x

USB interface connector: 1 (USB Hi-speed)

Interface

USB host: 2 Network interface: 1 (10BASE-T/100BASE-TX)

Page description language PRESCRIBE

1-1-3

Scanner

2MA/2MB

Item Specifications

Operating system

System requirements

Resolution 600 dpi, 400 dpi, 300 dpi, 200 dpi

File format JPEG, TIFF, PDF, XPS

Simplex

Scanning

speed

Duplex

Interface Ethernet (10 BASE-T/100 BASE-TX)

Network protocol TCP/IP

Transmission system

Windows 2000 (Service Pack 4), Windows XP, Windows Vista, Windows 7, Windows Server 2003, Windows Server 2008

IBM PC/AT compatible CPU: Celeron 600 MHz or higher RAM: 128 MB or more HDD free space: 20 MB or more Interface: Ethernet

B/W : 35 images/min Color: 25 images/min (A4 landscape, 300 dpi, Image quality: Text/Photo original)

B/W : 18 images/min Color: 13 images/min (A4 landscape, 300 dpi, Image quality: Text/Photo original)

PC transmission SMB Scan to SMB FTP Scan to FTP, FTP over SSL E-mail transmission SNTP Scan to E-mail TWAIN scan* WIA scan*

*1 Available operating system: Windows 2000 (Service Pack 4), Windows XP, Windows Vista,

Windows Server 2008, Windows 7

*2 Available operating system: Windows Vista, Windows Server 2008, Windows 7

1-1-4

FAX (4 in 1 model (with FAX) only)

Item Specifications

Compatibility G3

Communication line Subscriber telephone line

Transmission time 3 s or less (33600 bps, JBIG, ITU-T A4 #1 chart)

2MA/2MB

Transmission speed

Coding scheme JBIG/MMR/MR/MH

Error correction ECM

Original size

Automatic document feed Max. 50 sheets

Scanner resolution

Printing resolution 600 × 600 dpi

Gradations 256 shades (Error diffusion)

One-Touch key 22 keys

Multi-Station transmission Max. 100 destinations

Substitute

memory reception

Image memory capacity 3.5 MB (standard) (for incoming faxed originals)

33600/31200/28800/26400/24000/21600/19200/16800/14400/12000/9600/ 7200/4800/2400 bps

Max. width: 8 1/2"/216 mm Max. length: 14"/356 mm

Horizontal × Vertical 200 × 100 dpi Normal (8 dot/mm × 3.85 line/mm) 200 × 200 dpi Fine (8 dot/mm ×7.7 line/mm) 200 × 400 dpi Super fine (8 dot/mm × 15.4 line/mm) 400 ×400 dpi Ultra fine (16 dot/mm ×15.4 line/mm)

256 sheets or more (when using ITU-T A4 #1 chart)

Report output

NOTE: These specifications are subject to change without notice.

Sent result report, FAX RX result report, Report for job canceled before sending, Activity report, Status page

1-1-5

1-1-2 Parts names

1. Document processor (DP)

2. Contact glass

3. Original size Indicator plate

4. Operation panel

5. Inner tray lever

6. Paper stopper

7. Inner tray

8. MP (Multi-Purpose) tray

9. Cassette

10. USB memory slot

11. Main power switch

12. Toner container K

13. Toner container M

14. Toner container C

15. Toner container Y

16. Waste toner cover

17. Waste toner box

18. Lock release button

(1) Machine (front side)

2MA/2MB

12131415

Figure 1-1-1

1-1-6

(2) Machine (rear side)

19. Rear cover

20. Rear cover lever

21. IF cover

22. Memory cover

23. Power cord cover

24. Paper conveying unit

25. Power cord connector

26. Network indicators

27. Network interface connector

28. USB interface connector

29. USB memory slot

30. LINE connector*

31. TEL connector*

*: 4 in 1 model (with FAX) only

2MA/2MB

Figure 1-1-2

1-1-7

(3) Document processor

32. DP top cover

33. Original width guides

34. Original table

35. Original eject table

36. Switchback table

37. Original stopper

38. Opening Handle

2MA/2MB

Figure 1-1-3

1-1-8

(4) Operation panel

1. System menu/Counter key

2. Document box key

3. Status/Job cancel key

4. Copy key

5. Send key

6. FAX key*

7. Address book key

8. Address recall/Pause key*

9. Confirm/Add destination key

10. On Hook key*

11. One-touch keys

12. Shift Lock key

13. Auto color key

14. Full color key

15. Black and White key

16. Message display

17. Left Select key

18. Right Select key

19. Processing indicator

20. Memory indicator

21. Attention indicator

22. Back key

23. Cursor keys

24. OK key

25. Function Menu key

26. Numeric keys

27. Clear key

28. Reset key

29. Stop key

30. Start key

31. Program keys

32. Main power LED

33. Power key

34. Logout key

*: 4 in 1 model (with FAX) only

2MA/2MB

31 2

4 7 8 9 10 16

12 18

13 14

1511 17

27 32 3328

19 20

20 22 23 26 31 3430

Figure 1-1-4

1-1-9

1-1-3 Machine cross section

1. Cassette paper feed section

2. MP tray paper feed section

3. Paper conveying section

4. Laser scanner unit KM

5. Laser scanner unit CY

6. Drum unit K

7. Drum unit M

8. Drum unit C

9. Drum unit Y

10. Developing unit K

11. Developing unit M

12. Developing unit C

13. Developing unit Y

14. Toner container section

15. Primary transfer section

16. Secondary transfer/Separation sections

17. Fuser section

18. Eject/Feed shift sections

19. Duplex section

20. Image scanner unit

21. Document processor

2MA/2MB

Original path

Paper path

1248 11 7 10 6

Figure 1-1-5

1-1-10

2MA/2MB

1-2 Installation

1-2-1 Installation environment

1. Temperature: 10 to 32.5°C/50 to 90.5°F

2. Humidity: 15 to 80% RH

3. Power supply: 120 V AC, 9 A 220 - 240 V AC, 5 A

4. Power source frequency: 50 Hz ±2%/60 Hz ±2%

5. Installation location Avoid direct sunlight or bright lighting. Ensure that the photoconductor will not be exposed to direct sunlight or other strong light when removing paper jams. Avoid locations subject to high temperature and high humidity or low temperature and low humidity; an abrupt change in the environmental temperature; and cool or hot, direct air. Avoid places subject to dust and vibrations. Choose a surface capable of supporting the weight of the machine. Place the machine on a level surface (maximum allowance inclination: 1). Avoid air-borne substances that may adversely affect the machine or degrade the photoconductor, such as mercury, acidic of alkaline vapors, inorganic gasses, NOx, SOx gases and chlorine-based organic solvents. Select a well-ventilated location.

6. Allow sufficient access for proper operation and maintenance of the machine.

400 mm 15 3/4"

300 mm300 mm

300 mm 11 13/16"11 13/16"11 13/16"

600 mm 23 5/8"

Figure 1-2-1

1-2-1

1-2-2 Unpacking

Unpacking

1. Machine

2. Outer case

3. Machine cover (620 × 580)

4. Bottom spacer

5. Plastic bag (650 × 650)

6. Left spacer

7. Bottom pads

8. Bottom case

9. Front pad

10. Top spacer

11. Top pad L

12. Top pad R

13. Plastic bag (240 × 350)

14. Installation guide etc.

15. CD-ROM*

16. Middle spacer

17. Power cord

18. Waste toner box

19. Toner containers

20. Plastic bags (200 × 450)

21. Plastic bag (250 × 600)

22. Operation labels

23. Operation label pad

24. Modular cable**

25. Hinge joints *: 240 V AC model only. **: 4 in 1 model (with FAX) only.

220-240 V AC model

2MA/2MB

17 18

Figure 1-2-2

1-2-2

120 V AC model

1. Machine

2. Outer case

3. Machine cover (620 × 580)

4. Bottom spacer

5. Plastic bag (650 × 650)

6. Left spacer

7. Bottom pads A

8. Bottom pads B

9. Bottom case

10. Front pad

11. Top spacer

12. Top pad L

13. Top pad R

14. Plastic bag (240 × 350)

15. Installation guide etc.

16. CD-ROM

17. Middle spacer

18. Power cord

19. Waste toner box

20. Toner containers

21. Plastic bags (200 × 450)

22. Plastic bag (250 × 600)

23. Operation labels

24. Operation label pad

25. Modular cable*

26. Plastic bag*

27. Hinge joints *: 4 in 1 model (with FAX) only.

2MA/2MB

Figure 1-2-3

Place the machine on a level surface.

1-2-3

1. Open the DP.

Removing the tapes and pads

2. Remove two tapes.

3. Remove the sheet.

2MA/2MB

Tap e

Sheet

Tap e

4. Remove the paper.

Figure 1-2-4

Paper

Figure 1-2-5

1-2-4

2MA/2MB

5. Remove tape A and pad.

6. Move the lock lever to the position of release.

* : When turning on power if the lock lever

is not released, the error message is displayed.

7. Remove tape B.

8. Close the DP.

Tape A

Pad

Lock lever

Tape B

Figure 1-2-6

9. Remove two tapes.

Ta pe

Figure 1-2-7

1-2-5

2MA/2MB

10. Open the DP top cover.

11. Remove two tapes.

12. Close the DP top cover.

DP top cover

Ta pe

Figure 1-2-8

13. Remove six tapes.

Ta pe

Ta pe s

Ta pe

1-2-6

Figure 1-2-9

+ 282 hidden pages

Kyocera FS-C2026, FS-2126MFP Service Manual [UK ]

Revision history

Safety precautions

CONTENTS

1-1-1 Specifications

Specifications

1-1-2 Parts names

(1) Machine (front side)

(2) Machine (rear side)

(3) Document processor

(4) Operation panel

1-1-3 Machine cross section

1-2-1 Installation environment

1-2-2 Unpacking