Kyocera FS-3040, FS-3140MFP Service Bulletin 2LW 003

Service Bulletin

SB Number:

Subject:

SB 2LW-003

Firmware upgrade

Creation Date: 15/09/2010

Model: FS-3040MFP/3140MFP

Item Contents

1 Adjusting the scanner command. The setup parameter to adjust the scanner command has been added.

2 Clearing the click charge/machine

life count.

3 Error code F145. Error code F145 may occur, when receiving information 100 times or more

Firmware

Type Program No. Check SUM Version Status Date Applicable models

ENGINE 2LW_1000.002.001 c43f 002.001 04/06/2010 FS-3040MFP/3140MFP

MAIN 2LW_2F00.004.003 ---- 004.003 ---------- FS-3040MFP

MAIN 2LX_2F00.004.003 ---- 004.003 ---------- FS-3140MFP

FAX 2H9_54000003003 ---- ------- ---------- FS-3140MFP

Maintenance mode U927 has been added to clear the click charge and the
machine life count.

via URDS.

Classication

Field measure Please upgrade the rmware to the latest version to implement the above mentioned changes.

Serial numbers of affected machines

Type Serial number

FS-3040MFP/3140MFP August 2010 production.

The above mentioned changes have been applied to machines produced after the above mentioned production date.

Item 1: Adjusting the scanner command. (Command and parameter)

KCFG “SCAN“, #1[ ,#2, #3]

Adjusting the DP scanning timing

#1 Set item 2 DP scanning timing

#2 Set target Value Refer to set target below

#3 Input value

Adjusting the DP center line

#1 Set item 3 DP center line

#2 Set target Value Refer to set target below

#3 Input value

Adjusting the DP magnication

#1 Set item 4 DP magnication

#2 Set target Value Refer to set target below

#3 Input value

Entire stock rework

In-eld modication at next visit

In-eld modication by case

No modication necessary

KMIS Service Department, Kyocera Mita Europe A288 / SB 2LW-003

Page 1 of 2

Service Bulletin

Adjusting the scanner leading edge

#1 Set item 5 Scanner leading edge

#2 Set target Value Refer to set target below

#3 Input value

Adjusting the scanner center line

#1 Set item 6 Scanner center line

#2 Set target Value Refer to set target below

#3 Input value

Adjusting the scanner magnication

#1 Set item 8 Scanner magnication

#2 Set target Value Refer to set target below

#3 Input value

Adjusting the scanner center line DP

#1 Set item 9 DP scanning position

#2 Set target Value Refer to set target below

#3 Input value

Item 1: Corresponding maintenance mode number and set target.

#1 Number Item #2 Name Min Max

2 U071 Adjusting the DP scanning timing 1 Front head -32 32

2 Front tail -32 32

3 Back head -45 45

4 Back tail -45 45

5 180 degree rotated -128 127

3 U072 Adjusting the DP center line 1 DP center line (Data1) -39 39

2 DP center line (Data1) -39 39

3 DP center line (Data1) -39 39

4 U070 Adjusting the DP magnication 2 DP magnication -25 25

5 U066 Adjusting the scanner leading edge

registration

6 U067 Adjusting the scanner center line 1 Table center line (Data1) -70 70

8 U065 Adjusting the scanner center line 1 Y scan zoom (Main) -32 127

9 U068 Adjusting the scanning position originals

from the DP read/DP back

1 Table leading edge (Data1) -45 45

2 Table leading edge (Data1) -45 45

2 Table center line (Data1) -40 40

2 X scan zoom (Sub) -25 25

1 DP read (Dat1) -33 33

2 DP back line (Test pos) 0 3

KMIS Service Department, Kyocera Mita Europe A288 / SB 2LW-003

Page 2 of 2