Konica Minolta DiMAGE Z10 User Manual

Download

Page 1

INSTRUCTION MANUAL

9222-2735-11 SY-A406/0406/109678

Page 2

EFORE YOU BEGIN

Thank you for purchasing this digital camera. Please take the time to read through this instruction manual so you can enjoy all the features of your new camera. Check the packing list before using this product. If any items are missing, immediately contact your camera dealer.

DiMAGE Z10 digital camera Neck strap NS-DG800 Lens cap LF-243B SD Memory Card Video cable VC-400 USB cable USB-3 4 AA alkaline batteries DiMAGE Viewer CD-ROM “DiMAGE Instruction Manuals”-CD-ROM Quick Reference Guide International Warranty Certificate

This product is designed to work with accessories manufactured and distributed by Konica Minolta. Using accessories or equipment not endorsed by Konica Minolta may result in unsatisfactory performance or damage to the product and its accessories.

BEFORE YOU BEGIN

Konica Minolta is a trademark of Konica Minolta Holdings, Inc. DiMAGE is a trademark of Konica Minolta Photo Imaging, Inc. Apple, Macintosh, and Mac OS are registered trademarks of Apple Computer Inc. Microsoft and Windows are registered trademarks of the Microsoft Corporation. The official name of Windows is Microsoft Windows Operating System. Pentium is a registered trademark of the Intel Corporation. Power PC is a trademark of the International Business Machines Corporation. QuickTime is a trademark used under license. All other brand and product names are trademarks or registered trademarks of their respective owners.

While reasonable efforts have been made to assure the accuracy of this information, Konica Minolta assumes no liability or responsibility for any errors or omissions of this instruction manual.

Page 3

Read and understand all warnings and cautions before using this product.

Using batteries improperly can cause them to leak harmful solutions, overheat, or explode which may damage property or cause personal injury. Do not ignore the following warnings.

•Only use the batteries specified in this instruction manual.

•Do not install the batteries with the polarity (+/–) reversed.

•Do not use batteries which show wear or damage.

•Do not expose batteries to fire, high temperatures, water, or moisture.

•Do not attempt to short, or disassemble batteries.

•Do not store batteries near or in metallic products.

•Do not mix batteries of different types, brands, ages, or charge levels.

•Do not charge alkaline batteries.

•When recharging rechargeable batteries, only use the recommended charger.

•Do not use leaking batteries. If fluid from the batteries enters your eye, immediately rinse the eye with plenty of fresh water and contact a doctor. If fluid from the batteries makes contact with your skin or clothing, wash the area thoroughly with water.

•Tape over battery contacts to avoid short-circuiting during disposal; always follow local regulations for battery disposal.

WARNING

•Use only the specified AC adapter within the voltage range indicated on the adapter unit. An inappropriate adapter or current may cause damage or injury through fire or electric shock.

•Do not disassemble this product. Electric shock may cause injury if a high voltage circuit inside the product is touched.

•Immediately remove the batteries or unplug the AC adapter and discontinue use if the camera is dropped or subjected to an impact in which the interior, especially the flash unit, is exposed. The flash has a high voltage circuit which may cause an electric shock resulting in injury. The continued use of a damaged product or part may cause injuries or fire.

FOR PROPER AND SAFE USE

Page 4

OR PROPER AND SAFE USE

•Keep batteries or small parts that could be swallowed away from infants. Contact a

doctor immediately if an object is swallowed.

•Store this product out of reach of children. Be careful when around children not to

harm them with the product or parts.

•Do not fire the flash directly into the eyes. It may damage eyesight.

•Do not fire the flash at vehicle operators. It may cause a distraction or temporary

blindness which may lead to an accident.

•Do not use the monitor while operating a vehicle or walking. It may result in injury or

an accident.

•Do not use this product in a humid environment, or operate this product with wet

hands. If liquid enters the product, immediately remove the batteries or unplug the AC adapter and discontinue use. The continued use of a product exposed to liquids may cause damage or injury through fire or electric shock.

•Do not use the product near inflammable gases or liquids such as gasoline, benzine,

or paint thinner. Do not use inflammable products such as alcohol, benzine, or paint thinner to clean the product. The use of inflammable cleaners and solvents may cause an explosion or fire.

•When unplugging the AC adapter, do not pull on the power cord. Hold the adapter unit

when removing it from an outlet.

•Do not damage, twist, modify, heat, or place heavy objects on the AC adapter cord. A

damaged cord may cause damage or injury through fire or electric shock.

•If the product emits a strange odor, heat, or smoke, discontinue use. Immediately

remove the batteries taking care not to burn yourself as the batteries become hot with use. The continued use of a damaged product or part may cause injuries or fire.

•Take the product to a Konica Minolta Service Facility when repairs are required.

•Handling the cord on this product may expose you to lead, a chemical known to the

State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling.

Page 5

•Do not use or store the product in a hot or humid environment such as the glove

compartment or trunk of a car. It may damage the product and batteries which may result in burns or injuries caused by heat, fire, explosion, or leaking battery fluid.

•If batteries are leaking, discontinue use of the product.

•The lens retracts when the camera is turned off. Touching the lens barrel while it is

retracting may cause injury.

•The camera temperature rises with extended periods of use. Care should be taken to

avoid burns.

•Burns may result if the memory card or batteries are removed immediately after

extended periods of use. Turn the camera off and wait for it to cool.

•Do not fire the flash while it is in contact with people or objects. The flash unit

discharges a large amount of energy which may cause burns.

•Do not apply pressure to the LCD monitor. A damaged monitor may cause injury, and

the liquid from the monitor may cause inflammation. If liquid from the monitor makes contact with skin, wash the area with fresh water. If liquid from the monitor comes in contact with the eyes, immediately rinse the eyes with plenty of water and contact a doctor.

•When using the AC adapter, insert the plug securely into the electrical outlet.

•Do not use if the AC adapter cord is damaged.

•Do not cover the AC adapter. A fire may result.

•Do not obstruct access to the AC adapter; this can hinder the unplugging of the unit

in emergencies.

•Unplug the AC adapter when cleaning or when the product is not in use.

CAUTION

Page 6

ABLE OF CONTENTS

The basic operation of this camera is covered between pages 12 and 33. This section of the manual covers the camera parts, preparation of the camera for use, and the basic camera operation for recording, viewing, and deleting images.

Many of the features of this camera are controlled with menus. The menu navigation sections concisely describe how to change menu settings. Descriptions of the settings immediately follow the navigation sections.

ABOUT THIS MANUAL

Names of parts ....................................................................................................................................10

Getting up and running ........................................................................................................................12

Attaching the strap and lens cap ............................................................................................12

Inserting batteries....................................................................................................................13

Battery condition indicator ......................................................................................................14

Auto power save .....................................................................................................................14

Connecting the optional AC adapter ......................................................................................15

Changing the memory card.....................................................................................................16

Turning on the camera and displays .......................................................................................17

Setting the date and time........................................................................................................18

Setting the menu language .....................................................................................................19

Basic recording ....................................................................................................................................20

Handling the camera ...............................................................................................................20

Using the zoom lens................................................................................................................20

Recording images automatically .............................................................................................21

Basic recording operation .......................................................................................................22

` Automatic Digital Subject Program Selection.........................................................................23

Focus lock ...............................................................................................................................24

Focus range.............................................................................................................................24

Focus signals ..........................................................................................................................25

Special focusing situations .....................................................................................................25

Flash modes ............................................................................................................................26

Flash range - auto-recording mode ........................................................................................27

Camera-shake warning ...........................................................................................................27

i+ button..................................................................................................................................28

Adjusting monitor brightness ..................................................................................................28

Digital subject programs .........................................................................................................29

Basic playback.....................................................................................................................................30

Single-frame playback and histogram display........................................................................30

Page 7

Viewing and rotating images ...................................................................................................31

Deleting single images ............................................................................................................31

i+ button..................................................................................................................................32

Enlarged playback...................................................................................................................33

Advanced recording.............................................................................................................................34

Recording mode display .........................................................................................................34

Macro ......................................................................................................................................35

Program (P) exposure mode ...................................................................................................36

Aperture priority (A) exposure mode .......................................................................................36

Shutter priority (S) exposure mode .........................................................................................37

Manual (M) exposure mode ....................................................................................................38

Time exposures .......................................................................................................................39

Movie recording.......................................................................................................................40

Exposure compensation..........................................................................................................41

Focus area selection ...............................................................................................................42

Navigating the recording menus .............................................................................................43

Drive modes ............................................................................................................................45

Self-timer .................................................................................................................................46

Continuous advance ...............................................................................................................47

Progressive capture.................................................................................................................48

Bracketing ...............................................................................................................................49

What is an Ev? ........................................................................................................................50

Image size and image quality..................................................................................................51

Auto DSP.................................................................................................................................53

Digital zoom.............................................................................................................................53

Focus modes...........................................................................................................................54

White balance..........................................................................................................................55

Automatic white balance .................................................................................................55

Preset white balance .......................................................................................................55

Custom white balance .....................................................................................................56

Full-time AF .............................................................................................................................57

Flash mode..............................................................................................................................57

Flash compensation ................................................................................................................57

Metering modes ......................................................................................................................58

Camera sensitivity - ISO .........................................................................................................59

Flash range and camera sensitivity.........................................................................................59

Color mode..............................................................................................................................60

Page 8

ABLE OF CONTENTS

Contrast .........................................................................................................................................60

Sharpness ...............................................................................................................................61

Custom key function ............................................................................................................................62

Image size (Movie) ...............................................................................................................................64

Frame rate ...............................................................................................................................64

Movie file sizes ........................................................................................................................64

Movie mode.............................................................................................................................65

A short guide to photography..............................................................................................................66

Advanced playback..............................................................................................................................68

Playing back movies ...............................................................................................................68

Capturing a movie frame.........................................................................................................69

Navigating the playback-mode menu .....................................................................................70

Frame-selection screen...........................................................................................................72

Delete ......................................................................................................................................73

Format .....................................................................................................................................74

Lock.........................................................................................................................................75

Copy and E-mail Copy............................................................................................................76

Slide Show ..............................................................................................................................78

About DPOF ............................................................................................................................80

DPOF setup .............................................................................................................................80

Date print.................................................................................................................................81

Index print ...............................................................................................................................81

Viewing images on a television ...............................................................................................82

Setup menu .........................................................................................................................................83

Opening the setup menu.........................................................................................................83

Navigating the setup menu .....................................................................................................84

LCD monitor brightness ..........................................................................................................86

Auto power save .....................................................................................................................86

Instant playback ......................................................................................................................86

Lens accessory .......................................................................................................................87

Language.................................................................................................................................87

File number (#) memory ..........................................................................................................87

Folder name ............................................................................................................................88

Noise reduction .......................................................................................................................88

Date and time setup................................................................................................................89

Date imprinting ........................................................................................................................89

Reset default ...........................................................................................................................90

Audio signals ...........................................................................................................................91

Page 9

Focus signal .........................................................................................................................................92

Shutter FX................................................................................................................................92

Video output ............................................................................................................................92

Transfer mode .........................................................................................................................92

Self-timer .................................................................................................................................92

Data-transfer mode ..............................................................................................................................93

System requirements ..............................................................................................................93

Connecting the camera to a computer ...................................................................................94

Connecting to Windows 98 and 98SE ....................................................................................95

Automatic installation ......................................................................................................95

Manual installation ...........................................................................................................96

Memory card folder organization ............................................................................................98

Auto power save - data-transfer mode...................................................................................99

Disconnecting the camera ...................................................................................................100

Windows 98 and 98 Second Edition .............................................................................100

Windows Me, 2000 Professional, and XP .....................................................................100

Mac OS..........................................................................................................................101

Changing the memory card .................................................................................................102

Uninstalling the driver software - Windows ..........................................................................103

PictBridge..............................................................................................................................104

Notes on printing errors ........................................................................................................105

Navigating the PictBridge menu ...........................................................................................106

Appendix .......................................................................................................................................110

Troubleshooting.....................................................................................................................110

Care and storage...................................................................................................................112

Camera care ..................................................................................................................112

Storage ..........................................................................................................................112

Cleaning.........................................................................................................................112

LCD monitor care ..........................................................................................................113

Batteries.........................................................................................................................113

Operating temperatures and conditions........................................................................113

Memory cards................................................................................................................114

Before important events and journeys ..........................................................................115

Copyright .......................................................................................................................115

Questions and service ...................................................................................................115

QuickTime system requirements...........................................................................................116

Technical specifications ........................................................................................................118

Page 10

AMES OF PARTS

* This camera is a sophisticated optical instrument. Care should be taken to keep these surfaces clean. Please read the care and storage instructions in the back of this manual (p. 112).

NAMES OF PARTS

The battery-chamber door (p. 13) and tripod socket are located on the bottom of the body.

Flash* (p. 26)

AF window*

Lens*

Shutter-release button

Self-timer lamp (p. 46)

Flash-mode button (p. 26)

Exposure-mode dial (p. 21, 29, 36 - 40)

Strap eyelet (p. 12)

Card slot (p. 16)

USB port/Video-out terminal (p. 82, 94, 104)

Page 11

Diopter-adjustment dial (p. 17)

Viewfinder* (p. 17)

Macro button (p. 35)

Zoom lever

(p. 20)

Controller

Access lamp

LCD monitor*

DC terminal (p. 15)

Menu button

Quick View / Delete button (p. 30, 31)

Information button (p. 28, 32)

Mode switchMain switch

Page 12

ETTING UP AND RUNNING

GETTING UP AND RUNNING

Always keep the strap around your neck in the event that the camera is accidentally dropped. An optional leather neck strap, NS-DG1000, is also available from your Konica Minolta dealer. Availability varies with region.

ATTACHING THE STRAP AND LENS CAP

Using your thumb and index finger, pinch the outside tabs of the lens cap to remove or attach. When the camera is not in use, always replace the lens cap.

Pass the end of the neck strap through the strap eyelet on the camera body (1).

Thread the strap through the inside of the buckle as shown (2). Repeat with the other end of the strap.

Page 13

INSERTING BATTERIES

Insert the batteries as indicated on the diagram on the inside of the battery-chamber door. Confirm the positive and negative battery terminals are oriented correctly.

To open the battery-chamber door, slide the lock to the open position (1). Slide the door to the front of the camera (2) to release the safety catch. Lift the door to open (3).

This digital camera uses four AA-size alkaline or Ni-MH batteries. Do not use other types of AA batteries. The camera should be off when replacing batteries.

Close the battery-chamber door and slide it toward the back of the body (4) to engage the safety catch. Slide the batter-chamber lock to the close position (5).

Page 14

ETTING UP AND RUNNING

BATTERY CONDITION INDICATOR

This camera is equipped with an automatic battery-condition indicator. When the camera is on, the battery-condition indicator appears on the monitor. If the monitor is blank, the batteries may be exhausted or installed incorrectly.

AUTO POWER SAVE

To conserve battery power, the camera turns off displays and unnecessary functions if an operation is not made within a minute. To restore power, press any button or key, or turn the exposure-mode dial to another position. The length of the auto-power-save period can be changed in section 1 of the setup menu (p. 86).

Full-battery indicator - the battery is fully charged. This indicator is displayed for three seconds on the monitor when the camera is turned on.

Low-battery indicator - battery power is low. The monitor will turn off while the flash is charging to save power.

Low-battery warning - battery power is very low. The monitor indicator is red. The battery should be replaced as soon as possible. This warning automatically appears and remains on the monitor until the battery is changed. The monitor will turn off while the flash is charging to save power. If power falls below this level, the battery-exhausted message will be displayed just before the camera shuts down. If the low-battery warning is displayed, movie recording cannot be used.

Page 15

CONNECTING THE OPTIONAL AC ADAPTER

The AC Adapter allows the camera to be powered from an electrical household outlet. The AC Adapter is recommended when the camera is interfaced with a computer or during periods of heavy use. AC Adapter model AC-1L is for use in North America and Japan, and AC-11 is for use in all other areas.

Insert the mini plug of the AC adapter into the DC terminal (1).

Insert the AC adapter plug into an electrical outlet.

Always turn off the camera before changing between power supplies.

Page 16

ETTING UP AND RUNNING

CHANGING THE MEMORY CARD

An SD Memory Card or MultiMediaCard must be inserted for the camera to operate. If a card has not been inserted, a no-card warning is displayed on the monitor. For more about memory cards see page 114.

Always turn off the camera and confirm the access lamp is not lit before removing a memory card; damage and data loss may result.

1.Insert the memory card all the way into the card slot and release; the card should catch in the slot. Insert the card so the face is toward the back of the camera. Always push the card in straight, never at an angle. Never force the card. If the card does not fit, check that it is oriented correctly.

2.To eject a memory card, press the card into the slot and release. The card can then be pulled out. Take care when removing the card as it becomes hot with use.

A memory card used in another camera may have to be formatted before being used. If the unable-to-use-card message appears, the card should be formatted with the camera. A memory card can be formatted in section 1 of the playback menu (p. 74). When a card is formatted, all the data on the card is permanently erased. If the carderror message appears, press the central button of the controller to close the window; check the Konica Minolta web site for the latest compatibility information:

North America: http://www.konicaminolta.us/ Europe: http://www.konicaminoltaeurope.com/

1 2

Page 17

TURNING ON THE CAMERA AND DISPLAYS

Press the main switch to turn the camera on. Pressing the switch again turns the camera off.

Around the main switch is the mode switch. This switch is used to change between the recording and playback modes as well as the selecting the between the monitor and viewfinder display.

Recording mode (Monitor display) - the camera can record images and the monitor is viewed directly.

Playback mode (Monitor display) - images can be played back and edited. The monitor is viewed directly.

To use the viewfinder in the playback mode, press and hold the flash mode button (1) and then press and hold the information (i

) button (2) until the monitor switches

to the viewfinder position.

Camera notes

Recording mode (Viewfinder display) - the camera can record images and the monitor is viewed through the viewfinder. The viewfinder has a built-in diopter. While looking through the viewfinder, turn the diopteradjustment dial until the monitor image is sharp

Page 18

ETTING UP AND RUNNING

Use the left and right keys to select the item to be changed.

Use the up and down keys to adjust the item.

Press the central button to set the clock and calendar.

SETTING THE DATE AND TIME

After initially inserting a memory card and batteries, the camera’s clock and calendar must be set. When images are recorded, the image data is saved with the date and time of recording.

If the clock and calendar have not been set, a message is displayed for a few seconds each time the camera is turned on. This message is also displayed if the clock and calendar are reset when the camera is stored without batteries for a long period.

Date/Time setup screen

MM / DD / YYYY

00 : 00

Date/Time set

:enter

2004 . 01 . 01

Set date / time?

NoYes

Use the left and right keys of the controller (1) to select “Yes.” “No” cancels the operation.

Press the center of the controller to open the date/time setup screen.

The date/time setup screen can be opened in section 2 of the setup menu.

:sel.:move

Page 19

Use the down key to highlight the language menu option, then press the right key.

Press the central button of the controller to set the language.

Press the central button of the controller to open the language screen.

SETTING THE MENU LANGUAGE

For customers in certain areas, the menu language may have to be set. Press the menu button (1) to open the menu; the appearance of the menu will depend on the position of the camera’s controls.

Navigating the menu is simple. The up/down and left/right keys of the controller (2) move the cursor and change settings on the menu. The central button of the controller selects menu options and sets adjustments.

Digital

Use the right key of the controller to highlight “SETUP” at the top of the menu.

Image Quality Auto D

Drive mode Image size Quality Auto DSP Digital zoom

Drive m

Off

Standard

2048x1536

Single

Press the central button of the controller to open the setup menu.

Language

Lens acc.

Inst.Playback

Power save

LCDbrightness

English

Use the four-way keys of the controller to highlight the new menu language.

Español

Français

/CHN

English

/JPN

Deutsch

Page 20

ASIC RECORDING

BASIC RECORDING

While using the viewfinder or LCD monitor, grip the camera firmly with your right hand while supporting the body with your left. Keep your elbows at your side and your feet shoulder-width apart to hold the camera steadily. Take care not to cover the lens with your fingers or the strap.

HANDLING THE CAMERA

This section covers the basic operation of this camera. Thoroughly familiarize yourself with the operations in this section before moving on to the other sections in the manual.

USING THE ZOOM LENS

The zoom lever controls the lens (1). Pressing the right (T) side of the lever will zoom in to the telephoto position of the lens. Pressing the left (W) side of the lever will zoom out to the wide-angle position.

After zooming, the zoom scale is displayed briefly. If the digital zoom (p. 53) is active, the yellow section of the scale indicates the digitalzoom range.

Turn on the camera. Set the mode switch to a recording position.

Zoom scale

Page 21

RECORDING IMAGES AUTOMATICALLY

Turn the exposure-mode dial to the auto-recording position (1); all camera operations are now fully automatic. The autofocus, exposure, and imaging systems will work together to bring beautiful results effortlessly.

While many of the camera’s systems in this mode are automatic. The flash mode (p. 26) and drive mode (p. 45) can also be changed. Image size and quality can be set on the auto-recording menu (p. 44, 51-52).

Metering mode

* Changes to the flash mode, focus area, or drive mode are reset when the exposure-

mode dial is turned to another position.

** When the sports action subject program is selected with Automatic Digital Subject

Program Selection (p. 23), the camera continues to focus when the shutter-release button is held partway down (continuous AF).

Multi-segment (fixed)

Camera sensitivity (ISO)

Flash mode

Focus area

Focus control

Drive mode

Auto (fixed) Autoflash (can be changed*)

Single-frame advance (can be changed*)

Color mode

White balance

Natural Color (fixed) Auto (fixed)

Autofocus - single-shot AF (fixed**)

Wide focus area (can be changed*)

– – – – – – – –

The camera uses the exposure system to control the brightness of the live monitor image. This is achieved by varying the CCD sensitivity and controlling the aperture. The aperture can sometimes be heard stopping down or opening up with changes in subject brightness.

Camera notes

Page 22

ASIC RECORDING

Press the shutter-release button all the way down to take the picture.

The example uses auto recording. Except for movie recording, the operation for other exposure modes is the same. Automatic Digital Subject Program Selection is only available in the auto recording mode.

Place the subject anywhere within the focus frame. Make sure the subject is within the focus range of the lens (p. 24). For very close subjects, use the macro function (p. 35).

BASIC RECORDING OPERATION

Press the shutter-release button partway down to lock the focus and exposure. An AF sensor (a) is displayed to indicate the subject. Automatic Digital Subject Selection will choose the appropriate exposure mode, see the facing page. The focus signal (b) on the monitor will confirm focus lock. If the focus signal is red, the camera was unable to locate the subject. Repeat the previous steps until the signal is white. The shutter speed (c) and aperture (d) appears and turns black to indicate the exposure is locked.

a b

The recorded image can be previewed by continuing to hold down the shutter-release button after the image is captured. The instant-playback function can also be used (p.

86).

Camera notes

The access lamp lights indicating image data is being written to the memory card. Never remove a memory card while data is being transferred.

Page 23

AUTOMATIC DIGITAL SUBJECT PROGRAM SELECTION

Automatic Digital Program Selection chooses between program autoexposure and one of five digital subject programs. The digital subject programs optimize camera setting for various conditions and subjects. Automatic Digital Subject Program Selection is only available in auto recording and can be disabled in the auto-recording menu. For information on individual subject programs, see page 29.

A row of gray indicators at the top on the monitor display will indicate Automatic Digital Subject Selection is active. Place the subject in the focus frames; the procedure is the same as the basic recording operation described on page 22.

Press the shutter-release button partway down; the AF system will locate the subject and the Automatic Digital Subject Selection function will choose a subject program. If no indicators are displayed, program autoexposure is active. Press the shutter-release button all the way down to take the picture. Hold the camera steadily when the sunset subject program is selected as exposures can be long.

Program autoexposure (the Digital Subject Program indicators disappear)

Portrait

Sports action

Landscape

Sunset

Page 24

BASIC RECORDING

Focus lock prevents the AF system from focusing. This can be used with off-center subjects or when a special focusing situation prevents the camera from focusing (p. 25).

Without lifting your finger from the shutter-release button, recompose the subject within the image area. Press the shutter-release button all the way down to take the picture.

FOCUS LOCK

Place the subject within the focus frame. Press and hold the shutter-release button partway down.

• The focus signal indicates the focus is locked. The shutter speed and aperture value change from white to black indicating the exposure is locked.

• When the focus is set, an AF sensor is displayed on the live image to indicate the point of focus.

FOCUS RANGE

All distances are measured from the CCD. See page 35 for the marco focus range.

Approximate location of CCD plane

Wide-angle position

0.57m - ∞ (1.9ft - ∞) Telephoto position

1.57m - ∞ (5.1ft - ∞)

Page 25

The focus signal in the lower right corner of the LCD monitor indicates the focus status. The shutter can be released even if the camera cannot focus on the subject.

The camera may not be able to focus in certain situations. If the autofocus system cannot focus on a subject, the focus signal will turn red. In this situation, focus-lock on an object at the same distance as the main subject and then recompose the image on the monitor to take the picture.

The subject in the focus frame is low in contrast.

The subject is too dark.

Two subjects at different distances overlap in the focus frame.

The subject is near a very bright object or area.

When using the sports action digital subject program, the camera continually focuses when the shutter-release button is pressed partway down; the focus frames turn red. Keep the subject within the red focus frames. Focus lock cannot be used.

If the AF system cannot focus, focus lock can be used with object at the same distance as the main subject or the camera can be focused manually in the Digital Subject Program or program (P) exposure modes (p. 54).

FOCUS SIGNALS

SPECIAL FOCUSING SITUATIONS

Focus locked.

Focus confirmed (P, A, S, and M continuous AF focus mode and sports action digital subject program). Exposure continuously adjusts.

Cannot focus. The subject is too close or a special situation is preventing the AF system from focusing.

Page 26

ASIC RECORDING

To change the flash mode, simply press the flash mode button (1) until the appropriate mode is indicated.

Autoflash - the flash fires automatically in lowlight and backlit conditions.

Red-eye reduction - multiple flashes are used before the main flash burst to reduce red-eye; an effect caused by light reflected from the retina. Use in low-light conditions when taking photographs of people or animals. The preflashes contract the pupils of the subject’s eyes.

Fill-flash - the flash fires with each exposure regardless of the amount of ambient light. Fillflash can be used to reduce harsh shadows caused by strong direct light or sunshine.

Slow sync. - flash and ambient light exposures are balanced; red-eye reduction is used. Use slow sync. when in dark locations to reveal background details. Ask your subject not to move after the flash burst; the shutter may still be open for the background exposure. Because exposures can be long, the use of a tripod is recommended.

Flash cancel - the flash cannot fire.

FLASH MODES

Fill-flash

Autoflash

Fill-flash

Flash cancel

Autoflash with

red-eye reduction

Slow sync. with

red-eye reduction

Page 27

If the shutter speed falls below the point where the camera can be safely hand held, the camera-shake warning appears on the LCD monitor. Camera shake is slight blurring caused by subtle hand motion and is more pronounced at the telephoto position of the lens than at the wide-angle. Although the warning appears, the shutter can still be released. If the warning appears, place the camera on a tripod, use the built-in flash, or zoom the lens towards the wide-angle position until the warning disappears.

CAMERA-SHAKE WARNING

FLASH RANGE - AUTO-RECORDING MODE

The camera controls the flash output automatically. For well-exposed images, the subject must be within the flash range. Distance is given from the CCD plane. Because of the optical system, the flash range is not the same at the lens’ wide-angle position as it is at the telephoto position.

Approximate location of CCD plane

Camera-shake warning

If the flash output was sufficient to illuminate the subject, the OK indicator briefly replaces the flash-mode indicator after the exposure. The access lamp turns red and blinks slowly while the flash is charging; if battery power is low, the monitor turns off during this period.

If using continuous AF or the sports action subject program with flash, the monitor image reflects the exposure required for the flash when the shutter-release button is pressed partway down. This may cause the monitor image to appear dark in low-light situations.

Camera Notes

Wide-angle position

0.57 - 5.3m (1.87 - 17.39 ft) Telephoto position

1.57 - 5.3m (5.15 - 17.39 ft)

Page 28

ASIC RECORDING

Pressing the information (i+) button changes the monitor display. The display cycles among the standard display, real-time histogram, and live image only.

Standard display Live image only

Information button

i+BUTTON

ADJUSTING MONITOR BRIGHTNESS

Set LCD brightness

:adjust :enter

Low High

The monitor image can be made lighter or darker. The brightness level can be set individually for viewfinder and direct viewing. Turn the mode switch to the appropriate position. Press and hold the information (i

)

button to open the LCD brightness screen.

Use the left/right keys of the controller to adjust the brightness; the monitor image changes accordingly. Press the center of the controller or the menu button to set the brightness level.

The real-time histogram shows the approximate luminance distribution of the live image. This histogram cannot show the affect of flash illumination. The histogram of a recorded image may not show the same distribution as the real-time histogram.

Real-time histogram

Page 29

DIGITAL SUBJECT PROGRAMS

Sports action - used to capture action by maximizing shutter speeds. The AF system continuously focuses; see page 21. When using flash, the subject must be within the flash range (p. 27). A monopod is more flexible and compact than a tripod when shooting events.

Sunset - optimized to reproduce rich, warm sunsets. When the sun is above the horizon, do not point the camera toward the sun for prolonged periods of time. The intensity of the sun could damage the CCD. Between exposures, turn off the camera or cover the lens.

Night portrait - for deep, subtle night scenes. The use of a tripod is recommended. When used with flash, the subject and background exposures are balanced. The flash can only be used with close subjects such as with a portrait of a person. When using the flash, ask your subjects not to move after the burst; the shutter will still be open for the background exposure.

Landscape - optimized to produce sharp, colorful landscapes. Used with bright outdoor scenery.

Digital subject programs optimize the camera’s exposure, white-balance, and image-processing systems for specific conditions and subjects. Simply turn the exposure mode dial to select the appropriate subject program; the active subject program is displayed in the bottom left corner of the monitor

Portrait - optimized to reproduce warm, soft skin tones and a slight defocusing of the background. Most portraits look best at a telephoto setting; the longer focal length does not exaggerate facial features and the shallower depth of field softens the background. Use the built-in flash with strong direct sunlight or backlight to reduce harsh shadows.

Subject program indicator

Page 30

Images can be viewed in the Quick View or playback modes. This section covers the basic operations in both modes. The playback mode has additional functions, see page 68.

To view images from the playback mode, turn the mode switch to the playback position (1).

To view images from the recording mode, press the Quick View / delete button (2).

ASIC PLAYBACK

BASIC PLAYBACK

SINGLE-FRAME PLAYBACK AND HISTOGRAM DISPLAY

Date of capture

Frame number/ total number of images

Lock indicator (p. 75)

DPOF indicator (p. 80)

Image size (p. 51) Image quality (p. 51)

Time of

capture

Shutter speed

Aperture value

White-balance

setting (p. 55)

Sensitivity

setting (p. 59)

Degree of exposure

compensation (p. 41)

Folder name

Folder number - image file number

Histogram

Mode indicator

To display the histogram display, press the up key of the controller. Press the down key to return to single-frame playback.

Page 31

The histogram shows the luminance distribution of the image from black (left) to white (right). The 256 vertical lines indicates the relative proportion of that light value in the image. The histogram can be used to evaluate exposure, but displays no color information.

Quick View / Delete button

In Quick View or the playback mode, use the left/right keys of the controller to scroll through the images.

To rotate a vertical image, press the down key to cycle through the three positions: 90° counterclockwise, 90° clockwise, and horizontal.

To return to the recording mode from Quick View, press the menu button or shutter-release button partway down.

The displayed image can be deleted. Once deleted, an image cannot be recovered.

To delete the displayed image, press the Quick View / delete button. A confirmation screen will appear.

Press the central button of the controller to delete the image.

Use the left/right keys to highlight “Yes,” “No” will cancel the operation.

VIEWING AND ROTATING IMAGES

DELETING SINGLE IMAGES

Delete this frame?

Yes

Page 32

ASIC PLAYBACK

In index playback, the four-way keys of the controller will move the yellow border. When the image is highlighted with the border, the date of recording, the lock and printing status, and the frame number of the image are displayed at the bottom of the screen. The highlighted image can be deleted using the Quick Viiew / delete button (p. 31), or a movie clip can be played by pressing the central button of the controller. When the information (i+) button is pressed again, the highlighted image will be displayed in the single-frame playback mode.

The information (i+) button controls the display format. Each time the button is pressed, the display cycles through to the next format: full display, image only, index playback.

i+BUTTON

Full display

Index playback

Image only

Information button

Page 33

ENLARGED PLAYBACK

Use the four-way keys of the controller to scroll the image. When scrolling, the arrows in the display will disappear when the edge of the image has been reached.

In single-frame playback in Quick View or the playback mode, a still image can be enlarged up to 6X in 0.2 increments for closer examination.

To exit the enlarged playback mode, press the menu button or the central button of the controller.

The information (i+) button switches between showing the full display and the image only.

With the image to be magnified displayed, press the right (T) side of the zoom lever to activate the enlarged playback mode. The degree of magnification is displayed on the LCD monitor.

Press the right (T) side of the zoom lever to increase the image magnification. Press the left (W) side of the lever to decrease the magnification.

The locator in the top right corner of the monitor indicates the area of the image being displayed.

Page 34

DVANCED RECORDING

ADVANCED RECORDING

This section cover the advanced recording features of this camera. Read the basic recording section before moving on to this section.

3. Flash-mode indicator (p. 26)

7. White-balance indicator (p. 55)

8. Camera-sensitivity (ISO) display (p. 59)

12. Metering-mode indicator (p. 58)

10. Camera-shake warning (p. 27)

13. Shutter-speed display

14. Aperture display

24. Digital-zoom display (p. 53)

19. Drive-mode indicator (p. 45)

17. Date-imprinting indicator (p. 89)

18. Frame counter (p. 52)

25. Color-mode indicator (p. 60)

23. Image-size display (p. 51)

22. Image-quality indicator (p. 51)

2. Mode indicator

A. Focus frame B. Spot metering area (p. 58)

11. Exposure-mode indicator (p. 36 - 38)

15. Macro-mode indicator (p. 35)

9. Exposure-compensation display (p. 41)

4. Flash-compensation display (p. 57)

RECORDING MODE DISPLAY

1. Wide-angle converter indicator (p. 87)

5. Sharpness display (p. 61)

6. Contrast display (p. 60)

20. Manual-focus scale (p. 54)

16. Focus-mode indicator (p. 54)

21. Battery-condition indicator (p. 14)

Page 35

MACRO

Approximate location of

CCD plane

Macro indicator

Macro mode allows the camera to focus as close as 1 cm (0.4 in.) from the front of the lens or 8 cm (3.1 in.) from the CCD. The focus range changes with the zoom ‘s focal length, see below.

Press the macro button (1) to select the macro mode. Press the macro button again to cancel the macro mode.

The following chart lists the macro ranges. All distances are measured from the CCD.

Wide-angle position: 8 - 107cm (3.1 - 42.1 in.)

26.5 - 30.8mm: 107 - 237cm (42.1 - 93.3 in.)

Telephoto position: 67 - 207cm (26.3 - 81.5 in.)

Page 36

The photographer selects the aperture and the camera sets the appropriate shutter speed to ensure the correct exposure. When aperture priority is selected, the aperture value on the monitor turns blue and a double arrow indicator appears next to it. The flash mode can be set to fill-flash, fill-flash with red-eye reduction, or slow sync. with redeye reduction (p. 26).

DVANCED RECORDING

The program exposure mode controls both the shutter speed and aperture to ensure correct exposures. This exposure mode allows photographers to shoot without worry about exposure settings. The shutter speed and aperture values of the exposure are displayed on the monitor when the shutter-release button is pressed partway down. If shutter speed and aperture displays turn red, the scene is beyond the exposure control range of the camera.

PROGRAM (P) EXPOSURE MODE

Use the up/down keys of the controller (1) to set the aperture. The aperture has a three stop range. Press the shutter-release button partway down to activate the exposure system; the corresponding shutter speed will be displayed on the monitor.

As the lens is zoomed, the maximum aperture will automatically shift. If the aperture value is beyond the shutter-speed range, the shutter-speed display will turn red on the monitor.

APERTURE PRIORITY (A) EXPOSURE MODE

Page 37

The shutter speed and aperture control more than the exposure. The shutter speed determines how sharp a moving subject is. The aperture controls the depth of field; the area in front of the camera that appears sharp. For more on exposure controls, see the Short Guide to Photography on page

66.

The photographer selects the shutter speed and the camera sets the appropriate aperture to ensure correct exposure. When shutter priority is selected, the shutter speed on the monitor turns blue and a double arrow indicator appears next to it. The shutter speed can be set between 1/2000 and 15 seconds. If the shutter speed is beyond the aperture range, the aperture display will turn red. The flash mode can be set to fillflash, fill-flash with red-eye reduction, or slow sync. with red-eye reduction (p. 26).

Use the up/down keys of the controller (1) to set the shutter speed. Press the shutterrelease button partway down to activate the exposure system; the corresponding aperture will be displayed on the monitor.

SHUTTER PRIORITY (S) EXPOSURE MODE

Shooting Tips

When the shutter speed is one second or longer, the begining and end of the exposure.

Camera notes

Page 38

Manual exposure mode allows individual selection of shutter speeds and apertures. This mode overrides the exposure system giving the photographer total control over the final exposure.

DVANCED RECORDING

Use the up/down keys of the controller to change the shutter speed.

MANUAL (M) EXPOSURE MODE

The changes made to the exposure will be visible in the live image on the monitor. The monitor shutter-speed and aperture display will turn red if the image is significantly underexposed or overexposed. If the monitor is black, increase the exposure until the image is visible; decrease the exposure if the monitor is white. When the shutter-release button is pressed partway down, the brightness of the live image may change while the camera focuses.

In manual exposure mode, the auto camera-sensitivity setting will fix the ISO value at

100. The camera sensitivity can be changed in section 3 of the recording menu (p. 59). The flash mode can be set to fill-flash, fill-flash with red-eye reduction, or slow sync. with red-eye reduction (p. 26), but the live image will not reflect the flash exposure.

Use the left/right keys of the controller to change the aperture.

When the shutter speed is one second or longer, the begining and end of the exposure.

Camera notes

Page 39

A message is displayed during the exposure. Noise-reduction processing is applied to the image after the exposure. Noise reduction can be canceled in section 2 of the setup menu (p. 88).

Time photographs can be taken in the manual-exposure mode. Exposures up to thirty seconds can be made. The use of a tripod is recommended. The camera’s exposure system cannot be used to calculate time exposures. A separate light meter can be used to determine the exposure.

TIME EXPOSURES

Use the down key of the controller to decrease the shutter speed below 15 seconds until “T” is displayed.

Set the aperture using the left/right keys of the controller.

To take the picture, press the shutterrelease button (1) once to begin the exposure. Press it again to end the exposure.

Page 40

Before recording, the frame counter shows the maximum time in seconds that can be recorded on the next movie clip.

DVANCED RECORDING

Recording time

Frame the picture as described in the basic recording operation section (p. 22). Press the shutter-release button partway down to set the the focus and exposure. Press the shutter-release button all the way down and release to start recording.

Recording indicator Remaining time

MOVIE RECORDING

The camera continues to focus during recording. The camera will continue to record until the recording time is used or the shutter-release button is pressed again.

Image size

This camera records digital video without audio. Total recording time varies with the image size and frame rate, see page 64. Exposure compensation and the macro mode can be used. Other changes can be made with the movie recording menu (p. 44).

Frame rate

Page 41

To adjust the exposure, press the left or right controller key; the exposure-compensation screen appears.

Use the left/right keys of the controller to adjust the exposure-compensation value. Changes to exposure are visible in the live image.

Press the shutter-release button partway down or press the central button of the controller to set the adjustment.

The camera exposure can be adjusted to make the final picture lighter or darker by as much as ±2Ev in 1/3 increments. Exposure compensation can only be used with Digital Subject Programs, the P, A, and S exposure modes, and movie recording mode. With movie recording mode, exposure compensation is reset when the camera is turned off. In Digital Subject Programs, P, A, and S exposure modes, exposure compensation remains in effect until reset.

EXPOSURE COMPENSATION

When adjusting the exposure, the amount of compensation is shown in EV (p. 50). After the setting is made, the shutter-speed and aperture displays indicate the actual exposure. Because the exposure can be adjusted in fine steps, the shutter speed or aperture value displayed may not change. When set to any value other than zero, the exposure-compensation indicator remains on the monitor as a warning.

Exposure compensation is used when the camera’s exposure meter is deceived by high-key or low-key scenes. In the example, the dark water caused the camera to overexpose the image making it too bright and washed-out. By compensating the exposure, detail is brought out in the leaves, and the stones and water appear richer.

Camera notes

–2.0Ev

–1.0Ev

Camera exposure

Page 42

DVANCED RECORDING

Press the shutter-release button partway down or press the central button of the controller to select the area; the other two areas disappear. Only when a focus area has been selected, can the controller be used for other camera operations.

Take the picture as described in the basic recording section; press the shutter-release button partway down to lock focus and exposure. Press the shutter-release button all the way down to take the picture.

Once a focus area is selected, it will remain active even after the picture has been taken. Press and hold the central button of the controller to return to the standard focus frames.

Press and hold the central button of the controller until the three spot focus areas are displayed.

FOCUS AREA SELECTION

Use the left/right keys of the controller to highlight the desired autofocus area; the active area is blue.

Individual focus areas can be selected when recording still images. With auto recording and Digital Subject Programs, focus area selection is reset when the exposure-mode dial is moved to another position or the camera is turned off. In P, A, S, and M exposure modes, the selected focus area remains active until reset.

Page 43

Press the central button of the controller to select the highlighted setting; some options open a selection screen.

On the P, A, S, and M menu, use the left/right keys of the controller to highlight the appropriate menu tab; the menu changes as the tabs are highlighted.

The recording menu displayed varies with the position of the exposure-mode dial. There are four menus depending on if auto recording, movie recording, Digital Subject Programs, or the P,A,S, and M exposure modes are selected. See next page for details.

Use the up/down keys to scroll through the menu options. Highlight the option whose setting needs to be changed.

With the menu option highlighted, press the right controller key; the settings are displayed with the current setting highlighted. To return to the menu options, press the left key.

Use the up/down keys to highlight the new setting.

NAVIGATING THE RECORDING MENUS

Once a setting has been selected, the cursor will return to the menu options and the new setting will be displayed. To return to the recording mode, press the menu button.

Pressing the menu button (1) turns the menu on and off. The four-way keys of the controller (2) move the cursor in the menu. Pressing the central button of the controller enters a setting.

Activate the menu with the menu button.

Page 44

DVANCED RECORDING

Drive mode Image size Quality Auto DSP Digital zoom

Single 2048x1536 Standard On Off

Drive mode Image size Quality Focus mode Digital zoom

Single 2048x1536 Standard Autofocus Off

Drive mode Image size Quality

Key func.

Single

Standard Auto Flash mode

Focus mode Full-time AF Flash mode

Metering mode

Single AF On Autoflash 0 MultiSegment

Flash comp.

Sensitivity Digital zoom Color mode

Contrast

Auto Off NaturalColor Normal Normal

Sharpness

Auto-recording menu Digital Subject Program menu

Movie menu

P, A, S, and M exposure-mode menu

Focus mode, 54 Frame rate, 64 Full-time AF, 57 Image size, 51 Image size (movie), 64 Key function, 62 Metering mode, 58

Movie mode, 65 Quality, 51 Sensitivity, 59 Sharpness, 61 White balance, 55

Auto DSP, 53 Color mode, 60 Contrast, 60 Digital zoom, 53 Drive mode, 45 Flash compensation, 57 Flash mode, 57, 26

Index to menu functions

White balance

Focus mode Color mode

Cont. AF NaturalColor

Image size Frame rate White balance

320x240 15fps Auto STD. movieMovie mode

2048x1536

Page 45

The drive modes control the rate and method images are captured. The drive mode is set on all menus except the movie menu. In auto recording mode, the drive mode is reset to single-frame advance when the exposure-mode dial is moved to another position or the camera is turned off. In Digital Subject Programs and P, A, S, and M exposure modes, the drive mode remains in effect until changed. Refer to the following sections for descriptions of the drive modes.

DRIVE MODES

Single-frame advance - to take a single image each time the shutter-release button is pressed (p. 22).

Self-timer - to delay the release of the shutter. Used for self-portraits.

Continuous advance - to take multiple images when the shutter-release button is pressed and held.

Progressive Capture - to continuously record when the shutter-release button is pressed and held. Releasing the button saves the last six images.

Bracketing - to take a series of three images with differing exposures.

Page 46

DVANCED RECORDING

Used for self-portraits, the self-timer will delay the release of the shutter for approximately ten seconds or two seconds after the shutter-release button is pressed. The self-timer is set in section 1 of the recording menus (p. 44). The length of the self-timer delay is set in section 4 of the setup menu (p. 92).

The self-timer can be used to minimize camera shake with long exposures. When using the camera on a tripod, photographs of static subjects (landscapes, still-lifes, or close-up photographs) can be made with the self-timer. Because no contact is made with the camera during exposure, there is no risk of camera shake caused by the operator.

Shooting tips

SELF-TIMER

The self-timer is counted down on the monitor. During the countdown, the self-timer lamp on the front of the camera (3) will start to blink and is accompanied by an audio signal. A few seconds before the exposure, the self-timer lamp will blink rapidly. The lamp will glow steadily just before the shutter fires. To stop the countdown, press the right (T) side or the left (W) side of the zoom lever. When using a 10-second delay, the self-timer drive mode is reset to single-frame advance after the exposure. The audio signal can be turned off in section 3 of the setup menu (p. 91).

With the camera on a tripod, compose the picture so the subject is within the focus frames. Press the shutter-release button partway down to lock the exposure and focus (1). Press the shutter-release button all the way down to begin the countdown (2).

Because focus and exposure are determined when the shutter-release button is pressed, do not stand in front of the camera when taking a self-timer image. Always confirm the focus with the focus signals before beginning the countdown (p. 25).

1 2

Page 47

CONTINUOUS-ADVANCE MODE

The continuous-advance drive mode allow a series of images to be captured while holding down the shutter-release button. The number of images that can be captured at one time and the rate of capture depend on the image-size and image-quality settings. The maximum rate of capture is approximately 1.5 fps. This drive mode is set in section 1 of the recording menu.

Drive mode

Image size

Key func.

Self-timer

Single

Progressive Bracketing

Quality

Continuous

Compose the picture as described in the basic recording operation section (p. 22).

Press the shutter-release button partway down (1) to lock the focus exposure for the series.

Press and hold the shutter-release button all the way down (2) to begin taking pictures; focus is locked with the first frame. When the shutter-release button is pressed and held, the camera will begin recording images until the maximum number has been taken or the shutter button is released.

White balance

2048 X 1536

Fine 5

Standard 10

Economy 19

1600 X 1200

8 16 30

1280 X 960

13 24 42

640 X 480

42 67 94

The use of the built-in flash, the continuous-AF focus mode, or date imprinting (p. 89) reduces the rate of capture. The maximum number of images that can be captured with different image quality and size is as follows:

If the continuous AF focus mode (p. 54) is selected, the focus for the series is not locked. The AF system focuses between each frame. The exposure for the series is locked when the shutter-release button is pressed partway down.

Page 48

DVANCED RECORDING

PROGRESSIVE-CAPTURE MODE

The Progressive-Capture drive mode continuously records images while holding down the shutterrelease button. When the shutter button is released, the last six images stored in the camera’s buffer memory are recorded. This drive mode is set in section 1 of the recording menu. When the red lowbattery warning is displayed, these drive modes cannot be used.

Drive mode

Image size

Key func.

Self-timer

Single

Progressive Bracketing

Quality

Continuous

White balance

Compose the picture as described in the basic recording operation section (p. 22). Press the shutterrelease button partway down (1) to lock the focus exposure for the series.

Release the shutter (3) to save the images in the camera memory. The Progressive Capture records the last six images saved in the camera’s buffer memory. When a series is captured, a thumbnail of each image is shown in an index display while being saved.

The maximum rate of capture is approximately 1.3 fps. The use of the continuous-AF focus mode reduces the rate of capture. The built-in flash and date imprinting (p.

89) cannot be used.

1 2 3

Page 49

Drive mode

Image size

Key func.

Self-timer

Single

Progressive Bracketing

Quality

Continuous

This mode makes a three-image bracket of a scene. Bracketing is a method of taking a series of images of a static subject in which each image has a slight variation in exposure. The bracketing mode is set in section 1 of the recording menus.

Immediately after selecting the bracketing option on the menu, a selection screen is displayed to select the bracketing increment.

Press the left/right keys of the controller to select the bracketing increment. Press the central button of the controller to set the value. To change the increment, select the bracketing drive mode again with the menu.

BRACKETING

Compose the picture as described in the basic recording operation section (p. 22).

Press the shutter-release button partway down (1) to lock the focus exposure for the series.

Press and hold the shutter-release button all the way down (2) to make the bracket series; three consecutive images will be captured. Focus is locked with the first frame.

:select

:enter

White balance

1 2

Page 50

DVANCED RECORDING

Number of frames in bracketing series

Frame counter

When using exposure compensation (p. 41), the bracketing series will be made in relation to the compensated exposure. Under extreme conditions, one of the bracketed exposures may be inaccurate because it is outside the exposure control range of the camera.

The remaining number of frames in the bracket series is displayed on the monitor next to the bracketing indicator. If the memory is filled or the shutter button is released before the series has completed, the camera will reset and the entire bracket must be made again. If the red low-battery indicator appears, the bracketing drive mode is disabled. The flash cannot be used with the bracketing drive mode.

The order of the bracket series is normal exposure, underexposure, and overexposure. The exposure bracket can be made in 0.3, 0.5, or 1.0 Ev increments. The larger the number, the greater the difference in exposure between the images in the bracketed series.

0.3 Ev

bracket

0.5 Ev

bracket

1.0 Ev

bracket

Normal

Under

Over

WHAT IS AN EV?

Ev stands for exposure value. A change of one Ev adjusts the exposure calculated by the camera by a factor of two.

+2.0 Ev 4X as much light

2X as much light

Calculated exposure

1/2 as much light 1/4 as much light

+1.0 Ev ±0.0 Ev –1.0 Ev –2.0 Ev

Page 51

Changing image size affects the number of pixels in each image. The greater the image size, the larger the file size. Choose image size based on the final use of the image - smaller images will be more suitable for web sites whereas larger sizes will produce higher quality prints.

IMAGE SIZE AND IMAGE QUALITY

Image quality controls the rate of compression, but has no effect on the number of pixels in the image. The higher the image quality, the lower the rate of compression and the larger the file sizes. If economical use of the memory card is important, use the economy mode. Standard image quality is sufficient for normal usage. The fine mode will produce the highest quality image and the largest image files.

Image size and quality must be set before the picture is taken. Changes are displayed on the LCD monitor. Changes made on one menu affects all exposure modes except movie. Image size and quality must be reset manually. See navigating the recording mode menu section on page 43.

If image size or quality are changed, the frame counter will display the approximate number of images that can be recorded at that setting on the installed memory card. One memory card can contain images with differing sizes and qualities. The number of images that can be stored on a memory card is determined by the size of the card and the file size of the images. The actual file size is determined by the scene; some subjects can be compressed further than others. See the chart on the following page.

LCD monitor

2048 2048 X 1536 1600 1600 X 1200 1280 1280 X 960

640 640 X 480

Number of pixels

(hor. X vert.)

FINE Fine - high-quality JPEG image. STD. Standard - the default setting. (JPEG)

ECON. Economy - the smallest file sizes. (JPEG)

Page 52

DVANCED RECORDING

The frame counter indicates the approximate number of images that can be stored on the memory card at the camera’s image quality and size settings. If the settings are changed, the frame counter adjusts accordingly. Because the counter uses approximate file sizes, the actual image taken may not change the counter or may decrease it by more than one. When the frame counter displays zero, it indicates no more images at the image size and quality settings can be captured. Changing those settings may allow more images to be saved to the card.

Camera Notes

Approximate file sizes.

2048 X 1536 1600 X 1200 1280 X 960 640 X 480

Fine 1.3MB 770KB 550KB 170KB

Standard 830KB 440KB 300KB 120KB

Economy 440KB 290KB 210KB 100KB

Approximate number of images that can be stored on a 16MB memory card.

Fine 9 14 22 69

Standard 17 27 39 100

Economy 32 47 69 150

Page 53

AUTO DSP

Automatic Digital Subject Program Selection can be temporarily disabled in the auto-recording menu. When disabled, the program exposure mode is active. If the camera is turned off, Automatic Digital Subject Program Selection is activated.

Drive mode Image size Quality Auto DSP Digital zoom

Single 2048x1536 Standard On Off

DIGITAL ZOOM

The digital zoom is activated in the auto-recording, Digital Subject Program, and section 3 of the P, A, S, and M exposure-mode menus (p. 44).

The digital zoom extends the power of the telephoto position of the optical zoom by up to 4X in 0.1X increments. The transition between the optical zoom and digital zoom is seamless. When the digital zoom is active, the image magnification is displayed on the monitor and the focus frames change to a single focus area. Because of the degree of magnification, the use of a tripod is recommended.

The digital zoom is operated by the zoom lever (1). Press the right (T) side of the lever to zoom in to the telephoto position of the lens. When the digital zoom activates, the image magnification will be displayed on the monitor. Press the left (W) side of the lever to zoom out. After zooming, the zoom scale is displayed briefly. The yellow section indicates the digital-zoom range.

Digital-zoom images are interpolated to the set image size. Some loss of quality may be evident.

Magnification

Zoom scale

Page 54

DVANCED RECORDING

This camera has autofocus and manual focus control. The focus mode is selected separately in the Digital Subject Program, movie, and P, A, S, and M exposure-mode menus. The selected focus mode is not reset when the camera is turned off

With the P, A, S, or M exposure modes or movie recording, the autofocus mode can be specified between single-shot AF (AF-S) and continuous AF (AF-C) in section 2 of the menu (p. 44). Single-shot AF allows the focus to be locked before recording the image, see the basic recording section. Continuous AF continually focuses the camera. When capturing still images, the camera continues to focus when the shutter-release button is held partway down. In movie recording, focus is locked when the shutter-release button is partway down, but it is continually adjusted during recording.

FOCUS MODES

When using the shutter-priority, aperturepriority, or manual exposure modes (p. 36 - 38) with manual focus, press the central button of the controller to switch between using the up/down keys to focus or to adjust the exposure. The active function is indicated in blue.

When focusing manually, a scale shows the approximate subject distance. The scale changes depending on the focusing range.

Use the up/down controller keys to focus; the monitor image is automatically magnified by a maximum of 2.5X depending on the digital zoom setting. The live image returns to normal after two seconds, when zooming, or when the shutterrelease button is pressed partway down.

Page 55

Preset white-balance settings must be set before the image is taken. Once set, the effect is immediately visible on the LCD monitor.

Immediately after selecting the preset whitebalance option on the menu, a selection screen is displayed.

Press the left/right keys of the controller to select the preset white balance. Press the central button of the controller to apply it. The following preset options are available:

Automatic White Balance

Preset White Balance

The automatic white balance compensates for the color temperature of a scene. In most cases, the auto setting will balance the ambient light and create beautiful images, even under mixed-lighting conditions. When the built-in flash is used, the white balance is set for the color temperature of the flash.

White balance is the camera’s ability to make different types of lighting appear neutral. The effect is similar to selecting daylight or tungsten film, or using color compensating filters in conventional photography. An indicator will be displayed on the monitor if a setting other than auto white-balance is chosen. White balance is set independently in section 1 of the movie, and P, A, S, and M exposure-mode menus (p. 44).

WHITE BALANCE

Drive mode Image size

Key func.

Cust.set

Auto

Preset

Quality

CustRecall

White balance

:select

:enter

Daylight - for outdoor and sunlit subjects.

Cloudy - for overcast outdoor scenes.

Tungsten - for incandescent lighting: household light bulbs.

Fluorescent - for fluorescent lighting: office ceiling lights.

Flash - for use with the built-in flash.

Page 56

DVANCED RECORDING

Custom white-balance allows the camera to be calibrated to a specific lighting condition. The setting can be used repeatedly until reset. Custom white balance is especially useful with mixed-lighting or when critical control over color is needed. The object used to make a calibration must be neutral. A blank piece of white paper is an ideal surface and can easily be carried in a camera bag.

Custom White Balance

To calibrate the camera, select custom setup (Cust.set) from the white balance option in section 1 of the movie, and P, A, S, and M exposure-mode menus (p. 44); the custom white-balance calibration screen opens.

Fill the image area with a white object; the object does not need to be in focus. Press the central button of the controller to make the calibration or press the menu button to cancel the routine.

The live view shows the effect of the new white balance setting. The custom setting will remain in effect until another calibration is made or the whitebalance setting is changed.

If the custom white-balance setting is required again, select custom recall from the white-balance option of the menu; the last custom white-balance setting will be applied to the camera. The same custom white-balance setting is made and accessed from the movie, P, A, S, and M exposure modes.

Drive mode Image size

Key func.

Cust.set

Auto

Preset

Quality

CustRecall

White balance

Drive mode Image size

Key func.

Cust.set

Auto Preset

Quality

CustRecall

White balance

:enter

Page 57

FULL-TIME AF

With full-time AF active, the autofocus systems continually focuses to keep the monitor image sharp. This also reduces the autofocusing time when taking pictures. When the camera is set to manual focus, full-time AF is disabled. Turning the full-time AF function off can help conserve battery power. Full-time AF can be turned on and off in section 2 of the P, A, S, and M menus (p. 44).

FLASH MODE

The flash modes can be changed in section 2 of the P, A, S, and M menus (p. 44). This menu option is used when another function is assigned to the flash mode button, see page 62 on the custom key function. For more on flash modes, refer to page 26.

Focus mode Full-time AF Flash mode

Metering mode

Single AF On Autoflash 0 MultiSegment

Flash comp.

FLASH COMPENSATION

Flash compensation increases or decreases the flash exposure of the built-in flash in reference to the ambient exposure by as much as 2 Ev.

Select the flash compensation option section 2 of the P, A, S, and M menus (p. 44). Use the up/down keys to adjust the degree of compensation (1). Press the central controller button to set this value (2). If any value other than 0.0 is set, an indicator will be displayed on the monitor as a warning.

No compensation Negative compensationPositive compensation No flash

–2 ~ +2

Focus mode Full-time AF

Metering mode

+0.3

Flash mode

Flash comp.

Page 58

DVANCED RECORDING

Flash compensation changes the ratio between the ambient and flash exposures. When using fill-flash to reduce harsh shadows caused by direct sunlight, flash compensation changes the ratio between the highlights and shadows. The flash affects the darkness of the shadows without affecting the area illuminated by the sun. By decreasing the flash output with a negative Ev setting, the shadows receive less light and are deeper, but retain detail that would be lost without the flash. Using a positive Ev setting will soften or eliminate shadows.

Center weighted: a traditional metering method in film cameras. The system measures light values over the entire image area with emphasis given the central region.

Spot metering: uses a small area within the image to calculate the exposure. A small circle appears in the middle of the live image indicating the measuring area. The spot allows precise exposure measurements of a particular object without being influenced by extremely bright or dark areas within the scene.

Multi-segment metering: uses 256 segments to measure luminance and color. This data is combined with distance information to calculate the camera exposure. This advanced metering system will give accurate worry-free exposures in almost all situations.

Metering mode indicators are displayed on the monitor. The metering mode is set in section 2 of the P, A, S, and M menus (p. 44).

METERING MODES

Focus mode Full-time AF Flash mode

Metering mode

Single AF On Autoflash 0 MultiSegment

Flash comp.

Page 59

The flash range is measured from the CCD. Because of the optical system, the flash range is not the same at the lens’ wide-angle position as it is at the telephoto position.

CAMERA SENSITIVITY - ISO

FLASH RANGE AND CAMERA SENSITIVITY

Five camera sensitivity settings can be selected: Auto, 64, 100, 200, and 400; the numerical values are based on an ISO equivalent. ISO is the standard used to indicate film sensitivity: the higher the number, the more sensitive the film. Camera sensitivity is set in section 3 of the P, A, S, and M menus (p. 44).

Sensitivity Digital zoom Color mode

Contrast

Auto Off NaturalColor Normal Normal

Sharpness

The auto setting automatically adjusts the camera sensitivity to the light conditions between ISO 64 and 200. When any other setting than auto is used, “ISO” and the set value will be displayed on the monitor.

A specific sensitivity setting can be selected. As the ISO value doubles, the camera sensitivity doubles. Like grain in silver-halide film that increases with speed, noise increases with sensitivity in digital imaging; an ISO setting of 64 will have the least noise and 400 will have the most. An ISO setting of 400 may allow the camera to be handheld in low-light conditions without the need of a flash. The affect of noise with exposures of one second or longer is reduced by the noise-reduction function in section 2 of the setup menu (p. 88).

ISO setting Flash range (wide angle) Flash range (telephoto)

AUTO 0.57 - 5.3m (1.87 - 17.4ft.) 1.57 - 5.3m (5.15 - 17.4ft.)

0.57 - 3.0m (1.87 - 9.84ft.) 1.57 - 3.0m (5.15 - 9.84ft.)

0.57 - 3.8m (1.87 - 12.4ft.) 1.57 - 3.8m (5.15 - 12.4ft.)

0.57 - 5.3m (1.87 - 17.4ft.) 1.57 - 5.3m (5.15 - 17.4ft.)

0.57 - 7.5m (1.87 - 24.6ft.) 1.57 - 7.5m (5.15 - 24.6ft.)

100

200

400

Page 60

DVANCED RECORDING

COLOR MODE

The color mode controls whether a still image is color or black and white. This must be set before the image is recorded. The color mode is set in section 3 of the P, A, S, and M menus and section 2 of the movie menu (p. 44). The live image reflects the selected color mode. The color mode has no effect on image file size.

Natural Color reproduces the colors in the scene faithfully. This mode uses no monitor indicator when active. Vivid Color increases the saturation of the colors in the scene. Black & White produces neutral monochrome images. The sepia mode creates warmtone monochrome images.

CONTRAST

Contrast: normal

Contrast: low Contrast: high

This function increases or decreases the contrast of the scene in three levels: high (+), normal, and low (–). This can be set in section 3 of the P, A, S, and M menus (p. 44). Any changes made are applied to the live image. If any level except normal is selected, an indicator appears on the monitor as a warning.

Vivid color

Black & White

Sepia

Page 61

Sharpness: hardSharpness: soft

SHARPNESS

Sharpness accents or softens details in an image in three levels: hard (+), normal, and soft (–). This can be set in section 3 of the P, A, S, and M menus (p. 44).

Any changes made are applied to the live image, but may be difficult to see. However, when viewed with a computer, the changes will be evident. If any level except normal is selected, an indicator appears on the monitor as a warning.

Normal

Sensitivity Digital zoom Color mode

Contrast

Auto Off NaturalColor Normal Normal

Sharpness

Page 62

DVANCED RECORDING

CUSTOM KEY FUNCTION

Drive mode Image size

Key func.

Flash mode

Quality White balance

The function assigned to the flash-mode button can be selected among the flash mode, drive mode, white balance, focus mode, color mode, and sensitivity. This can be set in section 1 of the P, A, S, and M menus (p. 44). The flash mode can also be changed in section 2 of the P, A, S, and M menus.

After selecting the custom key function option on the menu, press the central button of the controller to display the selection screen. Use the four-way keys of the controller to select the function. Press the central button of the controller to set the custom key function. Pressing the menu button cancels the operation without changing the custom key function.

Pressing the flash-mode button changes the function set in the menu. Press the central button of the controller or press the shutter-release button partway down to apply the setting.

Color mode

Focus mode

Sensitivity

Drive mode

Flash mode

White balance

Selection screen

Page 63

:select

:enter

When selecting the bracketing drive mode, or preset white balance, a selection screen appears. Use the left/right keys of the controller to display the bracketing increment or preset white balance, and press the central button of the controller to select it.

:enter

When selecting custom white balance, the calibration screen appears. Fill the frame with a white object and press the central button of the controller to calibrate the camera.

Page 64

DVANCED RECORDING

IMAGE SIZE (MOVIE)

Movies can be recorded at two sizes: 640x480 and 320x240. The larger the image size, the higher the image quality and the larger the file sizes. Image size is set in section 1 of the movie menu (p. 44).

FRAME RATE

Movies can be recorded at two frame rates: 15 fps and 30 fps. 640x480 size image can only be recorded at 15fps. The higher the frame rate, the smoother the moving image and the larger the file sizes. Frame rate is set in section 1 of the movie menu (p. 44).

MOVIE FILE SIZES

If image size or frame rate is changed, the frame counter displays the approximate number of seconds that can be recorded with the installed memory card. The total time that can be stored on a memory card is determined by the size of the card and the recording rate. The actual file size is determined by the scene; some subjects can be compressed further than others.

Image size Frame rate White balance

320x240 15ps Auto STD. movieMovie mode

Approximate recording rate

Approximate number of seconds that can be stored on a 16MB memory card.

Frame rate

Image size

640 X 480 320 X 240

30 fps ----- 670KB/s

15 fps 540KB/s 340KB/s

30 fps ----- 21 seconds

15 fps 26 seconds 42 seconds

Page 65

MOVIE MODE

The movie mode option selects the type of movie recorded. Standard produces a normal movie clip. Night Movie uses high camera sensitivity to record under low light levels; camera sensitivity will automatically increase in low light. Image quality can be lower with Night Movies because of the higher sensitivity. The movie mode is set in section 1 of the movie menu (p. 44).

The writing speed of the memory card may prematurely end the recording of a movie clip. Test the card before important events. Check the Konica Minolta web site for the latest compatibility information:

North America: http://www.konicaminolta.us/ Europe: http://www.konicaminoltasupport.com.

Page 66

SHORT GUIDE TO PHOTOGRAPHY

A SHORT GUIDE TO PHOTOGRAPHY

Photography can be a rewarding pursuit. It is a broad and disciplined field that can take years to master. But the pleasure in making photographs and the joy of capturing a magical moment cannot be compared. The guide is an introduction to some basic photographic principles.

The lens aperture controls not only exposure, but also depth of field; the area between the closest object in focus and the furthest object in focus. The larger the aperture value, the greater the depth of field. The smaller the aperture value, the shallower the depth of field. The required shutter speed for the exposure increases with the aperture value. Usually landscape photographs use a large depth of field (large aperture value) to keep the foreground and background in focus, and portraits use a shallow depth of field (small aperture value) to separate the subject from the background.

Depth of field also changes with focal length. The smaller the focal length, the greater the depth of field; the longer the focal length, the shallower the depth of field.

Page 67

The shutter controls not only exposure, but also the ability to stop motion. Fast shutter speeds are used in sport photography to stop action. Slow shutter speeds can be used to show the flow of motion such as water cascading over a waterfall. The use of a tripod is recommended with slow shutter speeds.

The change in aperture and shutter speed is not apparent in the live image. Unlike film cameras, test photographs can be taken and immediately viewed. For critical work, take a test photograph at the set aperture or shutter speed and view the result in Quick View (p. 30). The image can be deleted if not acceptable and another test image can be taken at a different setting.

Page 68

Press the controller to pause the movie playback; press the controller again to resume the playback.

DVANCED PLAYBACK

Use the left/right keys of the controller to display the movie.

Press the center of the controller to play back the movie clip.

PLAYING BACK MOVIES

ADVANCED PLAYBACK

Press the display button to view the movie with or without the guidance bar.

During playback, the left/right keys rewind and fast forward the recording.

The basic functions in this mode are described in the basic playback section on pages 30 through 33. This section covers how to playback movie clips as well as the advanced function on the playback menu. Movie clips can be played back in Quick View.

To cancel the playback, press the menu button.

Pause

Play

Rew

Fwd

Page 69

CAPTURING A MOVIE FRAME

A single frame from a movie clip can be copied and saved as a still image. The copied image has the same image size as the original movie.

Pause Rew Fwd

During playback, press the center button of the controller to pause the movie playback at the point to capture the frame. When the movie is paused, the left/right keys can be used to jog the clip to display the correct frame.

Play Rew Fwd

Press the up key of the controller to capture the frame. Before the frame is captured, a confirmation screen appears. Choosing “Yes” executes the operation, “No” cancels it.

Play Rew Fwd

The file name of the captured image is displayed. Press the center button of the controller to complete the operation.

Saved as PICT0015.JPG.

Page 70

DVANCED PLAYBACK

Press the central button of the controller to select the highlighted setting.

Use the left/right keys of the controller to highlight the appropriate menu tab; the menu changes as the tabs are highlighted.

Use the up/down keys to scroll through the menu options. Highlight the option whose setting needs to be changed.

With the menu option highlighted, press the right controller key; the settings are displayed with the current setting highlighted. If “Enter” is displayed, press the center of the controller to continue.

Use the up/down keys to highlight the new setting.

Once a setting has been selected, the cursor will return to the menu options and the new setting will be displayed. To return to the playback mode, press the menu button.

Pressing the menu button (1) turns the menu on and off. The four-way keys of the controller (2) move the cursor in the menu. Pressing the central button of the controller enters a setting.

Activate the menu with the menu button.

NAVIGATING THE PLAYBACK MENU

Page 71

DPOF set Date print–Off

– –E-mail copy

Index print

Delete Format––

– –Copy

Lock

Slide show

Playback––

5 sec. NoRepeat

Duration

To delete images on the memory card (p. 73).

To format the memory card (p. 74).

To create an index print with the DPOF order (p. 81)

To protect images from deletion (p. 75).

To play back images automatically (p. 78)

To select the images for the Slide Show (p. 78).

To specify how long each image is played back (p. 78)

To repeat the Slide Show presentation automatically (p. 78).

To select images for DPOF printing (p. 80).

To print the date with the DPOF images (p. 81).

To copy and resize images to be e-mailed (p. 76).

Refer to the following sections for descriptions of the menu options.

To copy images from one memory card to another (p. 76).

Page 72

When a marked-frames setting is chosen on a menu, the frame selection screen will appear. This screen allows multiple images to be chosen.

The left/right keys of the controller moves the yellow border to select the image.

The up key of the controller selects the frame; when selected, an indicator appears next to the image. The down key deselects the image removing the indicator.

The menu button cancels the screen and any operation made.

The garbage can indicates the image is selected for deletion.

The key indicates the image is locked or selected to be locked.

The check indicates the image is selected for the slide show or to be copied.

FRAME-SELECTION SCREEN

Press the central button of the controller to complete the operation.

The printer icon indicates the image is selected for DPOF printing. The number of copies is shown on the right.

ADVANCED PLAYBACK

Movie file

E-mail copy file

Indicators may be displayed on the right of each index image to indicate movie and E-mail copy files.

:sel.

:enter

:move

Page 73

Deleting permanently erases the file. Once deleted, a file cannot be recovered. Care should be taken when deleting images.

Single, multiple, or all files on the memory card can be deleted in section 1 of the playback menu (p. 71). The delete option has three settings:

DELETE

Before a file is deleted, a confirmation screen appears. Choosing “Yes” executes the operation, “No” cancels it.

The delete function will only erase unlocked files. Locked files must be unlocked before they can be deleted.

Delete Format––

– –Copy

Lock

Delete this frame?

Yes

Delete –

This

frame

All

frames

Marked

frames

The file displayed or highlighted in the playback mode is deleted.

All unlocked files are deleted.

To delete multiple files. When this setting is chosen, the frame-selection screen is displayed. Use the left/right keys of the controller to highlight the first file to be deleted. Pressing the up key marks the thumbnail with the delete indicator. To deselect a file for deletion, highlight it with the yellow border and press the down key; the indicator disappears. Continue until all the files to be deleted are marked. Press the central button of the controller to continue (the confirmation screen appears), or press the menu button to cancel the operation and return to the playback menu. On the confirmation screen, highlighting and entering “Yes” deletes the marked files.

Page 74

The formatting function is used to erase all data on a memory card. Before formatting a memory card, copy the data to a computer or storage device. Locking images will not protect them from being deleted when the card is formatted. Always format the memory card using the camera; never use a computer to format a card.

When the format option is selected and entered in section 1 of the playback menu (p. 71), a confirmation screen appears. Choosing “Yes” formats the card, choosing “No” cancels the formatting operation. A screen appears to indicate the card has been formatted.

DVANCED PLAYBACK

FORMAT

When a memory card is formatted, all data on the card is erased.

A memory card used in another camera may have to be formatted before being used. If the unable-to-use-card message appears, the card should be formatted with the camera. If the card-error message appears, press the central button of the controller to close the window; check the Konica Minolta web site for the latest compatibility information:

North America: http://www.konicaminolta.us/ Europe: http://www.konicaminoltaeurope.com/

Delete Format––

– –Copy

Lock

Format?

Yes

Delete –

Page 75

Single, multiple, or all files can be locked. A locked file cannot be deleted by either the playback menu functions or the QV/delete button. However, the formatting function (p.

74) will erase all files on a memory card whether locked or not. Important images should be locked. The lock function is in section 1 of the playback menu (p. 71). The lock option has four settings:

LOCK

This

frame

All

frames

Marked

frames

The file displayed or highlighted in the playback mode is locked.

All files on the memory card are locked.

Unlock

all

All files on the memory card are unlocked.

To lock or unlock multiple files. When this setting is chosen, the frameselection screen is displayed. Use the left/right keys of the controller to highlight the file to be locked. Pressing the up key marks the file with the lock indicator. To unlock a file, highlight it with the yellow border and press the down key; the lock indicator disappears. Continue until all the files to be locked are marked. Press the central button of the controller to lock the marked thumbnails, or press the menu button to cancel the operation and return to the playback menu.

Page 76

DVANCED PLAYBACK

The copy function in section 1 of the playback menu (p. 71) makes exact copies of image or movie files and can store the copied data on another memory card. E-mail Copy in menu section 3 makes a standard 640 X 480 (VGA) JPEG copy of an original still image so that it may be easily transmitted by e-mail. E-mail copies can only be copied to the original card.

COPY AND E-MAIL COPY

Up to 32MB of data can be copied. If too many images have been selected, a warning will appear and the copy routine will be canceled. Divide the number of images into two or three batches. The amount of data can be converted into E-mail copies depends on the free space remaining on the memory card.

When a copy function is used, a folder is created for the files (p. 98); copy files are placed in a folder with a name ending in CP, and E-mail Copy images are placed in a folder ending in EM. The same folder is used to store copies until the number of images exceed 9,999. Copies of locked images are unlocked. DPOF information is not copied.

The copy and E-mail copy functions have two menu options:

Delete Format

Copy

Lock

DPOF set Date print–Off

– –E-mail copy

Index print

This

frame

Marked

frames

To copy the file displayed or highlighted in the playback mode.

To copy single or multiple files. When selected, the frame-selection screen will appear; highlight the file to be copied with the yellow border and then press the up key of the controller to mark it with the check indicator. To deselect a file to be copied, highlight the selected thumbnail and press the down key; the check disappears. Continue until all the files to be copied are marked. Press the central button of the controller to continue, or press the menu button to cancel the operation and return to the playback menu.

Page 77

Copied to 102KM_EM.

When the image(s) to be converted to an e-mail file are selected, the copy routine begins and a screen appears indicating the name of the folder containing the copied images; press the central button of the controller to return to the menu.

Copy

After the copy-completed message is highlighted, a screen indicates the name of the folder containing the copied images; press the central controller button to return to the menu.

When the image(s) to be copied are selected, a screen with four messages is displayed. The messages are highlighted during the copying procedure.

E-mail Copy

The copy-unsuccessful message appears when one or all of the images could not be copied. Check the memory card to see which files were copied and then repeat the procedure for the uncopied images.

Camera Notes

When the change-card message is highlighted, remove the camera’s memory card and insert the card to which the image should be copied. Press the central button of the controller to continue or the menu button to cancel the copy operation.

Copying completed.

Copy

Enter

Copying to camera memory. Change card. Copying to card.

To copy captured movie frames, the image size must be equal to or smaller than the frame image size.

Copied to 101KM_CP.

Page 78

DVANCED PLAYBACK

Section 2 of the playback menu controls the slide-show function. This function automatically displays all still images and movie clips on the memory card in order. The menu has the following options:

SLIDE SHOW

Slide show

Playback

Enter

All frames

Marked

frames

To start the slide-show presentation. Highlight “Enter” and press the central button of the controller to start the slide show.

To select all the images on the memory card to be displayed in the slide-show presentation.

To select specific images to be displayed in the slide-show presentation. When this setting is chosen, the frame-selection screen is displayed. Use the left/right keys of the controller to highlight the image to be included in the presentation. Pressing the up key will mark the image with a check indicator. To deselect a marked image, highlight it with the yellow border and press the down key; the check disappears. Continue until all the images have been edited. Press the controller to set the marked frames, or press the menu button to cancel the operation and return to the playback menu.

Duration 1 - 60s.

Repeat Yes / No

To select the period each still image is displayed during the slide show.

Selecting “Yes” causes the slide show to repeat until it is canceled using the menu button. “No” ends the slide show presentation and returns to the playback menu when all the images have been displayed once.

Page 79

Slide show

Playback––

5 sec. NoRepeat

Duration

Press the central button of the controller to pause and restart the slide show presentation.

Press the menu button to cancel the presentation

The presentation can be viewed without image information. Before opening the playback menu, press the information (i+) button to turn off the information display.

Camera Notes

The controller can be used to control the presentation during playback.

The left/right keys advance to the next still image or return to the previous one. During a movie, the keys forward or rewind the clip

Page 80

DVANCED PLAYBACK

The DPOF-set menu option is used to create an order for standard prints from still images on the memory card. Single, multiple, or all images can be printed. Print orders are created in section 3 of the playback menu (p. 71). The print menu option has four settings:

ABOUT DPOF

This camera is supported by DPOF™ version 1.1. The DPOF (Digital Print Order Format) allows direct printing of still images from digital cameras. After the DPOF file is created, the memory card is simply taken to a photofinishing service or inserted into the memorycard slot of DPOF compatible printers. When a DPOF file is created, a misc. folder is automatically created on the memory card to store it (p. 98).

DPOF SETUP

This

frame

To create a DPOF file for the displayed or highlighted image.

To create a DPOF file for all images on the memory card.

To chose a group of images to be printed or when the number of copies of each image varies. When selected, the frame selection screen appears. Use the left/right keys of the controller to highlight an image to be printed. Pressing the up key will mark the image with the print indicator. The number next to the indicator shows the number of copies that will be printed. Pressing the up key increases the number of copies, pressing the down key decreases the number. A maximum of nine copies can be ordered. To deselect an image for printing, press the down key until the number of copies reaches zero and the print indicator disappears. Continue until all the images to be printed are marked. Press the central button of the controller to create the DPOF file, or press the menu button to cancel the operation and return to the playback menu.

All

frames

Marked

frames

Cancel

all

To delete the DPOF file.

Page 81

When the this-frame or all-frames setting is chosen, a screen appears requesting the number of copies of each image; a maximum of nine copies can be ordered. Use the up/down keys of the controller to set the required number of copies. If the all-frames setting was used to create a print order, any additional images recorded afterwards will not be included in the order.

DPOF files created with another camera will be canceled. After the pictures have been printed, the DPOF file will still remain on the memory card and must be canceled manually.

INDEX PRINT

To create an index print of all the images on the card, select “Yes” in the index print option in section 3 of the playback menu. To cancel an index print, simply change the setting to “No.”

If an index-print order is created, any additional images saved afterwards on the card will not be included in the index print. The number of images printed per sheet differs between printers. The information printed with the thumbnails can vary.

DPOF files and images can be printed directly from the camera with a DPOF compatible PictBridge printer, see page 104.

Camera Notes

DATE PRINT

To print the date of capture with each image with a DPOF compatible printer, turn the section 3 menu option on. To cancel date print, simply turn the option off. How and where the date is printed varies with the printer.

Page 82

DVANCED PLAYBACK

VIEWING IMAGES ON A TELEVISION

It is possible to view camera images on your television. The camera has a video-out terminal to make the connection using the supplied Video cable VC-400. The camera is compatible with the NTSC and PAL standards. The video-output setting can be checked and set in section 4 of the setup menu (p. 92).

1.Turn off the television and the camera.

2.Insert the small plug of the video cable into the camera’s video-out terminal. The arrow mark on the plug should face the back of the camera.

3.Plug the other end of the video cable into the video input terminal on the television.

4.Turn the television on.

5.Change the television to the video channel.

6.Turn the camera’s mode dial to the playback position and turn on the camera. The camera’s monitors will not activate when the camera is attached to a television. The playback-mode display will be visible on the television screen.

7.View images as described in the playback section.

Page 83

The setup menu is used to control the camera’s functions and operation. The navigating the setup menu section covers the operation of the menu. The section is followed by detailed descriptions of the settings.

OPENING THE SETUP MENU

SETUP MENU

Digital

Image Quality Auto D

Drive mode Image size Quality Auto DSP Digital zoom

Drive m

LCDbrightness Power save Inst.Playback Lens acc. Language

– 1 min. Off None English

Setup menu

The setup menu is opened from the other menus. It can be accessed from any of the recording or playback menus.

Press the central button of the controller to open the setup menu.

Off

Standard

2048x1536

Single

Use the right key of the controller to highlight setup tab at the top of the menu.

Reverse the procedure to return to the original menu. Pressing the menu button closes the menu and returns to the recording or playback modes.

Page 84

ETUP MENU

Press the central button of the controller to select the highlighted setting. Once a setting has been selected, the cursor will return to the menu options and the new setting will be displayed.

Use the left/right keys of the controller to highlight the appropriate menu tab; the menu changes as the tabs are highlighted.

Use the up/down keys to scroll through the menu options. Highlight the option whose setting needs to be changed.

Use the up/down keys to highlight the new setting.

See page 83 on how to open the menu. The four-way keys of the controller (1) move the cursor in the menu. Pressing the central button of the controller enters a setting.

Close the menu with the menu button.

NAVIGATING THE SETUP MENU

Page 85

Video output Transfer mode

NTSC Data storage

Self-timer 10 sec.

Reset default Audio signals–1

1 1Shutter FX

Focus signal

LCDbrightness Power save Inst.Playback Lens acc. Language

– 1 min. Off None English

File # memory Folder name

Date imprint

Off Std. form On – Off

Date/Time set

Noise reductn

To set monitor brightness (p. 86).

To switch video output between NTSC and PAL (p. 92).

To set the menu language (p. 19).

To activate file number memory (p. 87).

To select the folder name format (p. 88).

To set the camera’s clock and calendar (p. 89, 18).

To reset camera functions (p. 90).

To change or turn off audio signals (p. 91).

To change or turn off the shutter sound effect (p. 92).

To set the auto power save period (p. 86).

To turn off noise reduction (p. 88).

To activate date imprinting (p. 89).

To play back a still image after it is recorded (p. 86).

Specified when using a lens accessory (p. 87).

To change or turn off the focus signal (p. 92).

To specify camera use with a computer or printer (p. 92).

To change the selt-timer delay period (p. 92).

Page 86

ETUP MENU

LCD MONITOR BRIGHTNESS

Monitor brightness can be adjusted in 11 levels. Brightness can be set individually for viewfinder and direct viewing in the recording mode. Turn the mode switch to the appropriate position before opening the brightness option in section 1 of the setup menu (p. 85). Also see page 28.

Use the left/right keys of the controller to adjust brightness, the monitor image changes accordingly. Press the central button of the controller to set the level.

AUTO POWER SAVE

To conserve battery power, the camera will shut down if no operation is made within a certain period. The length of the auto-power-save period can be changed to 1, 3, 5, or 10 minutes. When the camera is connected to a computer, the auto-power-save period is fixed at ten minutes. Auto power save is set in section 1 of the setup menu (p. 85).

An image can be displayed on the monitor after it is captured. When used with the continuous-advance or progressive-capture drive modes (p. 47, 48), the images in the series are played back in a six-frame index display. Instant playback is activated section 1 of the setup menu (p.

85). A playback period of two or ten seconds can be selected. To cancel the playback and save the image before the end of the playback period, press the shutter-release button partway down.

INSTANT PLAYBACK

Single still images can be previewed immediately after being captured without instant playback active. Simply continue to hold the shutter-release button down after taking the picture to display the image. Release the shutter button to end the playback.

Camera Notes

Set LCD brightness

:adjust

:enter

Low High

Page 87

LENS ACCESSORY

This camera is compatible with the optional Wide-angle Converter ZCW-200. This 0.7X wide-angle converter reduces the focal length of the zoom lens’ wide-angle position giving it the equivalent of a 26mm lens on a 35mm camera.

When the converter is mounted, the lens accessory option in section 1 of the setup menu should be set to “WideConvertr.” An indicator (WW) appears in the top left corner of the monitor as a warning. The optical zoom is automatically set to the wide-angle position. The optical zoom is disabled.

LANGUAGE

The language used in the menus can be changed in section 1 of the setup menu.

If file number memory is selected, when a new folder is created or a new memory card is used, the next image recorded will have a file number one greater than the last file saved. If the new card contains an image with a greater file number. the new image will be assigned a file number one greater than the greatest on the card. If the file number memory is disabled, the image file number is reset to 0001 when saved in a new folder or card. File number memory is activated in section 2 of the setup menu.

FILE NUMBER (#) MEMORY

File # memory Folder name

Date imprint

Off Std. form On – Off

Date/Time set

Noise reductn

Page 88

ETUP MENU

FOLDER NAME

All recorded images are stored in folders on the memory card. Two folder-name formats are available in section 2 of the setup menu, standard and date.

Standard folders have an eight character name. The initial folder is named 100KM008. The first three digits are the folder’s serial number, which will increase by one each time a new folder is created. The next two letters refer to Konica Minolta, and the last three numbers indicate the camera used; 008 indicates a DiMAGE Z10.

A date folder name also starts with the three digit serial number and is followed by one register for the year, two register for the month, and two registers for the day: 101YMMDD. The folder 10140625 was created in 2004 on June 25

With the date folder format selected, when an image is recorded, a new folder with the day’s date is created. All images recorded that day are placed in that folder. Images recorded on a different day are placed in a new folder with the corresponding date. If the file number memory function is off (p. 87), when a new folder is created, the serial number in the image-file name is reset to 0001. If file number memory function is on, the serial number in the image-file is one greater than the last image saved. For more information on folder organization and file names, see page 98.

100KM008

(Standard)

10140625

(Date)

NOISE REDUCTION

This function reduces the affect of dark noise caused by long exposures. Noise reduction is only applied to exposures of one second or longer. Dark-frame subtraction is applied to each image after it is captured. The processing time varies from image to image; a message will be displayed during this period. Noise reduction can be turned off in section 2 of the setup menu.

File # memory Folder name

Date imprint

Off Std. form On – Off

Date/Time set

Noise reductn

Page 89

DATE IMPRINTING

Every time a still image is recorded, it is stored with an exif tag that contains the date and time of recording as well as shooting information. This information can be viewed with the camera in the Quick View or playback mode, or on a computer with the DiMAGE Viewer software.

Camera Notes

The date is imprinted in the lower right corner of the image when viewed horizontally. It is printed directly on the photograph writing over the image information. The date can be imprinted in three formats: year / month / day, month / day / year, and day / month / year. The date and date format are set in section 2 of the setup menu (p. 85).

The date of recording can be printed directly on the image. The imprinting function must be activated in section 2 of the setup menu (p. 85) before the image is taken. Once activated, the date will continue to be imprinted until the function is reset; a yellow bar is displayed behind the frame counter to indicate the imprinting function is active.

Date-imprinting indicator

DATE AND TIME SETUP

It is important to accurately set the clock. When a still image or a movie clip is recorded, the date and time of the recording are saved with the image and are displayed during playback or can be read with the supplied DiMAGE Viewer software. The date format that is displayed or imprinted can be changed: YYYY/MM/DD (year, month, day), MM/DD/YYYY (month, day, year), DD/MM/YYYY (day, month, year). See page 18 for instructions on how to set the clock and calendar.

Page 90

ETUP MENU

RESET DEFAULT

This function affects all modes. When selected, a confirmation screen appears; choosing “Yes” resets the following functions and settings, “No” cancels the operation.

Recording mode

Focus area Wide frames p. 42

Monitor display Standard p. 28

Flash mode Autoflash (Fill-flash in A, S, M modes) p. 26

Image size 2048 X 1536 p. 51

Auto Digital Subject Selection On (Auto recording mode) p. 23

Focus mode Autofocus / Single-shot AF p. 54

Custom key function Flash mode p. 62

Flash compensation 0.0 p. 57

Camera sensitivity (ISO) Auto p. 59

Sharpness Normal p. 61

Exposure compensation 0.0 p. 41

Drive mode Single-frame advance p. 45

Image quality Standard p. 51

Digital zoom Off p. 53

White balance Auto p. 55

Full-time AF Off p. 57

Metering mode Multi segment p. 58

Color mode Natural color p. 60

Contrast Normal p. 61

Movie menu

Image size 320 X 240 p. 64

Frame rate 15 fps p. 64

Movie mode Standard movie p. 65

Color mode Natural color p. 60

White balance Auto p. 55

Focus mode Continuous AF p. 54

Page 91

AUDIO SIGNALS

Every time a button is pressed, an audio signal gives a positive confirmation of the operation. The audio signals can be turn off in section 3 of the setup menu (p. 85). The tone of the signal can also be changed.

Reset default Audio signals–1

1 1Shutter FX

Focus signal

Playback menu

Playback (Slide Show) All frames p. 78

Duration (Slide Show) 5 seconds p. 78

Date print Off p. 81

Repeat (Slide Show) No p. 78

Index print No p. 81

Setup menu

LCD brightness Normal p. 86

Auto-power-save period 1 minute p. 86

Lens accessory None p. 87

Folder name Standard p. 88

Date imprinting Off p. 89

Focus signals 1 p. 92

Transfer mode Data storage p. 92

Instant playback Off p. 86

File number (#) memory Off p. 87

Noise reduction On p. 88

Audio signals 1 p. 91

Shutter FX 1 p. 92

Self-timer 10 sec. p. 92

Page 92

ETUP MENU

VIDEO OUTPUT

Camera images can be displayed on a television (p. 82). The video output can be changed between NTSC and PAL in section 4 of the setup menu. North America uses the NTSC standard and Europe uses the PAL standard. Check which standard is used in your region to play back images on your television set.

SHUTTER FX

When the shutter is released, a shutter sound effect gives a positive confirmation a still image is recorded. The sound effect can be turn off in section 3 of the setup menu (p.

85). Two shutter effects are available.

SELF-TIMER

The self-timer delay period can be changed in section 4 of the setup menu (p. 85). Two delay periods are available, 10 seconds and 2 seconds.

FOCUS SIGNAL

When the shutter-release button is pressed partway down, an audio signal confirms the AF system has focused. The focus signals can be changed or turned off in section 3 of the setup menu (p. 85). Two tones are available.

TRANSFER MODE

The data-transfer mode must be specified depending on whether images are transferred to a computer or printed directly. The data-storage option must be selected to transfer data from the camera to a computer or when using the DiMAGE Viewer software. The PictBridge option allows images to be printed directly from the camera with a PictBridge compatible printer (p. 104).

Page 93

DATA-TRANSFER MODE

Read this section carefully before connecting the camera to a computer. Instructions on using and installing the DiMAGE Viewer software are found in the supplied software manual. The DiMAGE manuals do not cover the basic operation of computers or their operating systems; please refer to the manual supplied with your computer.

Check the Konica Minolta web site for the latest compatibility information:

North America: http://www.konicaminolta.us/ Europe: http://www.konicaminoltaeurope.com/software/pi_customer.html

Users with Windows 98 or 98 Second Edition will need to install the driver software on the included DiMAGE Viewer CD-ROM (p. 95). No special driver software is required for other Windows or Macintosh operating systems.

Customers who have bought a previous DiMAGE digital camera and have installed the Windows 98 driver software must repeat the installation procedure. The updated version of the driver software included on the supplied DiMAGE Viewer CD-ROM is required for the operation of the DiMAGE Z10 with a computer. The new software will have no affect on the performance of older DiMAGE cameras.

A remote camera driver is supplied in the Windows edition of the DiMAGE Viewer CDROM. The driver is not compatible with this camera.

SYSTEM REQUIREMENTS

For the camera to be connected directly to the computer and used as a mass-storage device, the computer must be equipped with a USB port as a standard interface. Both the computer and the operating system must be guaranteed by their manufacturers to support USB interface. The following operating systems are compatible with the camera:

Windows 98, 98SE, Me, 2000 Professional, and XP home and professional editions.

Mac OS 9.0 ~ 9.2.2 and Mac OS X v.10.1.3 - 10.1.5, v.10.2.1 ~ 10.2.8, v.10.3 ~10.3.3.

Page 94

ATA-TRANSFER MODE

CONNECTING THE CAMERA TO A COMPUTER

Confirm the battery has sufficient power before connecting the camera to a computer; the full-battery indicator should be displayed on the monitor. The use of the AC adapter (sold separately) is recommended over the use of the battery. For users with Windows 98 or 98 Second Edition, read the section on page 95 on how to install the necessary USB driver before connecting the camera to a computer.

1.Start up the computer. The computer must be on before connecting the camera.

2.Insert the memory card into the camera. To change the memory card while the camera is connected to a computer, see page 102.

3.Open the USB port/Video-out terminal cover. Attach the smaller plug of the USB cable to the camera. The arrow mark on the plug should face the back of the camera. Make sure the plug is firmly attached.

4.Attach the other end of the USB cable to the computer’s USB port. Make sure the plug is firmly attached. The camera should be connected directly to the computer’s USB port. Attaching the camera to a USB hub may prevent proper operation.

5.Press the main switch to turn on the camera. The USB connection is made automatically; a screen appears to indicate the operation. The monitor turns off when the connection has been made. If the USB connection is not made, disconnect the camera and restart the computer. Repeat the connection procedure above.

Initializing USB connection.

Page 95

When the USB connection is completed, a drive icon, or volume, appears in My Computer or the desktop; the name varies with memory card. When using Windows

XP or Mac OS X, a window opens requesting instructions on what to do with the image data; follow the directions in the window.

Windows XP

Mac OS X

Windows

Mac OS

The driver needs only to be installed once. If the driver cannot be installed automatically, it can be installed manually with the operating system’s add-new-hardware wizard; see the instructions on the following page. During installation, if the operating system requests the Windows

98 CD-ROM, insert it into the CD-ROM drive and follow the accompanying instructions on the screen. No special driver software is required for other Windows

or Macintosh operating systems.

CONNECTING TO WINDOWS 98 AND 98 SE

Before connecting the camera to the computer, place the DiMAGE Viewer CD-ROM in the CD-ROM drive. The DiMAGE installer menu should automatically activate. To automatically install the Windows

98 USB driver, click on the starting-up-the-USB-devicedriver-installer button. A window appears to confirm that the driver should be installed; click “Yes” to continue.

When the driver has been successfully installed, a window appears. Click “OK.” Restart the computer and connect the camera (p. 94) to complete the operation.

Automatic Installation

Page 96

ATA-TRANSFER MODE

Choose the recommended search for a suitable driver. Click “Next.”

Choose to specify the location of the driver. The browse window can be used to indicate the driver location. The driver should be located in the CDROM drive at :\Win98\USB. When the location is shown in the window, click “Next.”

Manual Installation

To install the Windows®98 driver manually, follow the instructions in the connecting-the-camera-to-acomputer section on page 94.

When the camera is plugged into the computer, the operating system will detect the new device and the add-new-hardware-wizard window opens. Place the DiMAGE Viewer CD-ROM in the CD-ROM drive. Click “Next.”

Page 97

The add new hardware wizard will confirm the location of the driver. The letter designating the CDROM drive will vary between computers. Click “Next” to install the driver in the system.

One of three drivers may be located: MNLVENUM.inf, USBPDR.inf, or USBSTRG.inf.

The last window confirms the driver has been installed. Click “Finish” to close the add new hardware wizard. Restart the computer.

When the my-computer window is opened, a new removable-disk icon is displayed. Double click on the icon to access the camera’s memory card; see page

98.

Page 98

ATA-TRANSFER MODE

Once the camera is connected to the computer, image files can be accessed by double clicking on icons. Image folders are located in the DCIM folder. The misc. folder contains DPOF print files (p. 80).

Files and folders on the memory card can be deleted using the computer. Never format the memory card from the computer; always use the camera to format the card. Only files recorded by the camera should be stored on the memory card.

MEMORY CARD FOLDER ORGANIZATION

Drive Icon

Dcim

PICT0001.JPG PICT0002.MOV

Still image Movie clip

Misc

100KM008 10140625 102KM_CP 103KM_EM

From left to right: standard folder, date folder, copy folder, e-mail copy folder.

Copy images (p. 76) are placed in a folder with a name ending in “CP.” E-mail Copy images are placed in a folder ending in “EM.” When a new folder is created, the first three digits in the folder name is one greater than the largest folder number on the card. When the index number in the image file name exceeds 9,999, a new folder is created with a number one greater than the greatest folder number on the memory card: e.g. from 100KM008 to 101KM008.

Image-file names begin with “PICT” followed by a four-digit file number and a .jpg or .mov extension. To copying images, simply drag and drop the file icon into a location in the computer.

Page 99

The number in the image file name may not correspond to the frame number of the image. As images are deleted in the camera, the frame counter will adjust itself to show the number of images on the card and reassign the frame numbers accordingly. The serial numbers used with image files will not change when an image is deleted. When a new image is recorded, it will be assigned a number one greater than the largest serial number in the folder. File serial numbers can be controlled with the file-number-memory function in section 2 of the setup menu (p. 87).

Image files contain Exif tag data. This data includes the time and date the image was recorded as well as the camera settings used. This data can be viewed with the camera or the DiMAGE Viewer software.

If a camera image is opened in an image-processing application that does not support Exif tags, and then the image is saved overwriting the original data, the Exif tag information is erased. Some Exif compatible applications rewrite the Exif data preventing the DiMAGE Viewer from reading it. When using software other than the DiMAGE Viewer, always make a backup copy of the image files to protect the Exif tag data.

To view images correctly on your computer, the monitor’s color space may need to be adjusted. Refer to your computer manual on how to calibrate the display to the following requirements: sRGB, with a color temperature of 6500K, and a gamma of 2.2. Changes made to the captured image with the camera’s contrast controls will affect any colormatching software in use.

AUTO POWER SAVE - DATA-TRANSFER MODE

When connected to a computer or printer, if the camera does not receive a read or write command within ten minutes, it will shut down to save power. When the camera shuts down, an unsafe-removal-of-device warning may appear on the computer monitor. Click “OK.” Neither the camera or computer will be damaged in this operation. Turn off the camera with the main switch. Remake the USB connection by turning the camera on.

Page 100

100

ATA-TRANSFER MODE

DISCONNECTING THE CAMERA

Windows Me, 2000 Professional, and XP

Confirm that the access lamp is not lit. Turn off the camera and then disconnect the USB cable.

To disconnect the camera, click once on the unplug-or-eject-hardware icon located on the task bar. A small window will open indicating the device to be stopped.

Windows 98 / 98 Second Edition

When more than one external device are connected to the computer, repeat the procedure above except right click on the unplug-or-eject-hardware icon. This will open the unplug-or-eject-hardware window after clicking on the small window indicating the unplug-or-eject-hardware routine.

Click on the small window to stop the device. The safe-to-removehardware window will open. Close the window, turn the camera off, and then disconnect the USB cable.

Never disconnect the camera when the access lamp is red - the data or memory card may permanently be damaged.

Konica Minolta DiMAGE Z10 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual