Kenwood KM240 Series Instruction Manual
KM240 series KM260 series
KM280 series
instructions
nglish 2 - 8
E
´¸∂w
01 - 61
T282 AT283
A
T282
A
T286 AT284
A
&
T283
A
AT281
AT285
efore using your Kenwood appliance/attachments
P
b
●
Read these instructions carefully and retain for future reference.
●
emove all packaging and any labels.
R
●
ash the parts: see ‘care and cleaning’.
W
●
Push excess cord in the cord storage compartment in the back of the
ppliance.
a
safety
●
witch off and unplug before fitting or removing tools and attachments, after
S
use and before cleaning.
●
ever let the cord hang down where a child could grab it.
N
●
eep your fingers away from moving parts and fitted tools/attachments.
K
Never put your fingers etc in the hinge mechanism.
●
ever leave the appliance unattended when it is operating.
N
●
ever use a damaged appliance or attachment. Get it checked or repaired:
N
see ‘service and customer care’.
●
Never let the power unit, cord or plug get wet.
●
ever use an unauthorised attachment or more than one attachment at a
N
time.
●
When using an attachment also read the safety information included in this
anual relating to that particular product.
m
●
Never exceed the maximum capacities.
●
Take care when lifting this appliance. Ensure the head is locked and that the
owl, tools, and cord are secure before lifting.
b
●
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
nowledge, unless they have been given supervision or instruction
k
concerning use of the appliance by a person responsible for their safety.
●
Children should be supervised to ensure that they do not play with the
ppliance.
a
●
Only use the appliance for its intended domestic use. Kenwood will not
accept any liability if the appliance is subject to improper use, or failure to
comply with these instructions.
before plugging in
●
Make sure your electricity supply is the same as the one shown on
the underside of your appliance.
important - UK only
●
The wires in the cord are coloured as follows:
Blue = Neutral,
Brown = Live.
●
The appliance must be protected by a 13A approved (BS1362) fuse.
Note:
●
For non-rewireable plugs the fuse cover MUST be refitted when replacing
the fuse. If the fuse cover is lost then the plug must not be used until a
replacement can be obtained. The correct fuse cover is identified by colour
and a replacement may be obtained from your Kenwood Authorised
Repairer (see Service).
●
If a non-rewireable plug is cut off it must be DESTROYED IMMEDIATELY. An
electric shock hazard may arise if an unwanted non-rewireable plug is
inadvertently inserted into a 13A socket outlet.
●
This appliance conforms to EC directive 2004/108/EC on Electromagnetic
Compatibility and EC regulation no. 1935/2004 of 27/10/2004 on materials
intended for contact with food.
key
kitchen machine
medium speed outlet
high speed outlet
tool socket
head release lever
mixer head
bowl
on/off and speed switch
power unit
cord storage compartment
beater
dough hook with removable guard
whisk
splashguard
attachments
Not all of the attachments listed will necessarily be included with your
itchen machine. Attachments are dependent upon the model variant.
k
blender
(AT282 and AT283)
mill (AT286)
citrus press
food processor
(AT284)
centrifugal juicer (AT285)
multi food grinder
AT281)
(
the mixing tools and some of their uses
beater
●
For making cakes, biscuits, pastry, icing, fillings, éclairs and mashed potato.
whisk
●
For eggs, cream, batters, fatless sponges, meringues, cheesecakes,
mousses, soufflés. Don’t use the whisk for heavy mixtures (eg creaming fat
and sugar) - you could damage it.
dough hook
●
For yeast mixtures.
to use your mixer
1 Press down on the head release lever and raise the mixer head until it
locks into position.
2 Select a tool and push into the tool socket .
●
Always ensure the guard is fitted onto the shaft of the dough hook before
inserting into the outlet. Once inserted fit the guard to the mixer outlet to
prevent food ingress.
3 Fit the bowl into the base and turn clockwise to lock into position .
4 Press down on the head release lever and lower the mixer head until it locks
into position.
5 Plug into the power supply then switch on and turn the speed switch to the
desired setting. To switch off turn to ‘0’.
●
Switch to pulse for short bursts
6 Unplug from the power supply.
7 Raise the mixer head and whilst holding it steady, pull the tool from the
outlet.
important
●
Some movement of the mixer head is normal when mixing
heavy loads such as bread dough.
●
If the mixer head is raised during operation, the machine will stop working
straight away. To re-start the mixer, lower the mixer head, turn the speed
switch to the off position, wait a few seconds and then re-select the speed.
The mixer should resume operating straight away.
●
If for any reason power to the mixer is interrupted and the machine stops
working, turn the speed switch to the off position, wait a few seconds and
then re-select the speed. The mixer should resume operating straight away.
●
The mixer will not operate unless all the outlet covers are
correctly fitted to the machine.
●
If you hear the machine labouring either switch off and remove
some of the mixture or increase the speed.
●
Always remove attachments fitted to the medium and high speed outlets
before raising the mixer head.
3
ints
h
●
Switch off and scrape the bowl with a spatula when necessary.
●
ggs at room temperature are best for whisking.
E
●
efore whisking egg whites, make sure there’s no grease or
B
egg yolk on the whisk or bowl.
●
se cold ingredients for pastry unless your recipe states otherwise.
U
●
hen creaming fat and sugar for cake mixes, always use the fat at room
W
temperature or soften it first.
●
our mixer has been fitted with a ‘soft start’ feature to minimise spillage.
Y
owever if the machine is switched on with a heavy mixture in the bowl
H
such as bread dough, you may notice that the mixer takes a few seconds to
each the selected speed.
r
points for bread making
mportant
i
●
ever exceed the maximum capacities stated - you will overload the
N
machine.
●
ome movement of the mixer head is normal when mixing heavy loads such
S
s bread dough.
a
●
The ingredients mix best if you put the liquid in first.
●
t intervals stop the machine and scrape the mixture off the dough hook.
A
●
ifferent batches of flour vary considerably in the quantities of liquid required
D
and the stickiness of the dough can have a marked effect on the load
mposed on the machine. You are advised to keep the machine under
i
bservation whilst the dough is being mixed; the operation should take no
o
longer than 6-8 minutes.
speed switch
hese are a guide only and will vary depending upon the quantity of mix in
T
the bowl and the ingredients being mixed.
beater
●
creaming fat and sugar start on min gradually increasing to a higher
speed
●
beating eggs into creamed mixtures use a medium to high speed
●
folding in flour, fruit etc use a low to medium speed
●
all in one cakes start on a low speed gradually increasing
to a higher speed
●
rubbing fat into flour use a low to medium speed
whisk
●
Gradually increase to maximum
dough hook
●
Use a low to medium speed
care and cleaning
●
Always switch off and unplug before cleaning.
power unit
●
ipe with a damp cloth, then dry.
W
●
ever use abrasives or immerse in water.
N
owl, tools, splashguard, removable guard on dough hook
b
●
Wash by hand, then dry thoroughly or wash in the dishwasher.
●
ever use a wire brush, steel wool or bleach to clean your stainless steel
N
owl. Use vinegar to remove limescale.
b
●
Keep away from heat (cooker tops, ovens, microwaves).
maximum capacities
shortcrust pastry 450g flour weight
sponge cake (one stage mix) 1.6 Kg total mix
fruit cake mix 1.8 Kg total mix
bread dough 500g flour weight
egg whites 8
electronic speed sensor control
Your mixer is fitted with an electronic speed sensor control that is designed
to maintain the speed under different load conditions, such as when
kneading bread dough or when eggs are added to a cake mix. You may
therefore hear some variation in speed during the operation as the mixer
adjusts to the load and speed selected - this is normal.
to fit and use the splashguard
1 Fit the bowl into the base and add the ingredients.
2 Fit the tool then lower the mixer head
3 Fit the splashguard onto the bowl by sliding the cut away section around the
mixer head .
4 To remove the splashguard reverse the above procedure.
●
During mixing, ingredients can be added directly to the bowl via the chute.
4
Loading...