Kenwood KDC-X700DAB User Manual

KDC-X700DAB

CD-RECEIVER

INSTRUCTION MANUAL

CONTENTS BEFORE USE

BEFORE USE 2

BASICS 3

GETTING STARTED 4

DIGITAL RADIO (DAB) 5

ANALOG RADIO 7

CD / USB / iPod 9

AUX 11

Pandora® 11

BLUETOOTH® 12

AUDIO SETTINGS 17

DISPLAY SETTINGS 18

MORE INFORMATION 18

TROUBLESHOOTING 19

SPECIFICATIONS 21

INSTALLATION / CONNECTION 23

How to read this manual

• Operations are explained mainly using buttons on the faceplate.

•

[XX]

indicates the selected items.

•

( XX)

indicates references are

available on the stated page.

Warning

Do not operate any function that takes your attention away from safe driving.

Caution

Volume setting:

• Adjust the volume so that you can hear sounds outside the car to prevent accidents.

• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.

General:

• Avoid using the USB device or iPod/iPhone if it might hinder safe driving.

• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.

• Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short circuit.

• If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.

Remote control (RC-406):

• Do not leave the remote control in hot places such as on the dashboard.

• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.

• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

• Keep the battery out of reach of children and in its original packaging when not in used. Dispose of used batteries promptly. If swallowed, contact a physician immediately.

Maintenance

Cleaning the unit: Wipe off dirt on the faceplate with a dry silicone or soft cloth. Cleaning the connector: Detach the faceplate and clean the connector

gently with a cotton swab, being careful not to damage the connector.

Handling discs:

• Do not touch the recording surface of the disc.

• Do not stick tape etc. on the disc, or use a disc with tape stuck on it.

• Do not use any accessories for the disc.

• Clean from the center of the disc and move outward.

• Clean the disc with a dry silicone or soft cloth. Do not use any solvents.

• When removing discs from this unit, pull them out horizontally.

• Remove burrs from the center hole and disc edge before inserting a disc.

Connector (on the reverse side of the faceplate)

BASICS

Faceplate

Remote control (RC-406)

Volume knob

(turn/press)

Detach button

Display window

How to resetAttach Detach

How to replace the battery

Your preset adjustments will also be erased.

Remote sensor (Do not expose to bright sunlight.)

To Do this (on the faceplate) Do this (on the remote control)

Turn on the power

Adjust the volume Turn the volume knob. Press VOL

Select a source

Change the display information

Press B SRC.

• Press and hold to turn off the power.

Press B SRC repeatedly.

Press DISPSCRL repeatedly.

• Press and hold to scroll the current display information.

Press and hold SRC to turn off the power. ( Pressing SRC does not turn on the power. )

or VOL .

Press ATT during playback to attenuate the sound.

• Press again to cancel.

Press SRC repeatedly.

( not available )

Pull out the insulation sheet when using for the first time.

ENGLISH |

GETTING STARTED

Cancel the demonstration

When you turn on the power (or after you reset the unit), the display shows: “CANCELDEMO”

1 Press the volume knob.

[YES]

is selected for the initial setup.

2 Press the volume knob again.

“DEMOOFF” appears.

Set the clock

Press the volume knob to enter

1 2 Turn the volume knob to select 3 Turn the volume knob to select 4 Turn the volume knob to make the settings, then press the knob.

Day Hour Minute

5 Turn the volume knob to select 6 Turn the volume knob to select 7 Press and hold to exit.

To return to the previous setting item or hierarchy, press .

“PRESS” “VOLUMEKNOB”

[FUNCTION] [CLOCK] [CLOCK ADJUST]

[CLOCK FORMAT] [12H]

, then press the knob.

[24H]

, then press the knob.

Set the initial settings

Press B SRC to enter STANDBY.

1 2 Press the volume knob to enter

[FUNCTION]

3 Turn the volume knob to make a selection (see the following table),

then press the knob.

4 Press and hold to exit.

To return to the previous setting item or hierarchy, press .

Default:

AUDIO CONTROL SP SELECT

DISPLAY EASY MENU

TUNER SETTING DAB L-BAND

DAB ANT POWER

PRESET TYPE

SYSTEM KEY BEEP TDF ALARM ON

OFF/ 5/4/ 6 × 9/6/ OEM

or 4inches, 6×9inches or 6inches) or OEM speakers for optimum performance.

:Both display and button illumination change to white color when

entering

[FUNCTION]

[COLOR SELECT]

:Receives L-BAND ensemble during digital audio reception.;

OFF

:Cancels.

ON:Supplies power to the DAB antenna. Selects when using the supplied antenna.;

OFF

antenna without booster.

NORMAL

: Memorizes one station for each preset button in each band (FM1/ FM2/ FM3/ MW/ SW1/ SW2/ DB1/ DB2/ DB3). ; station for each preset button, regardless of the selected band.

:Activates the keypress tone.; :Activates the alarm if you forget to detach the faceplate when ACC is

set to OFF.;

OFF

: Selects according to the speaker size (5inches

.;

OFF

:Both display and button illumination remain

color.

( 18)

:Does not supply power. Selects when using passive

( 25)

MIX

: Memorizes one

OFF

:Deactivates.

GETTING STARTED

SOURCE SELECT

PANDORA SRC

BUILT-IN AUX

CD READ

F/W UPDATE

UPDATE SYSTEM / UPDATE BT/ UPDATE DAB1/ UPDATE DAB2

F/W UP xx.xx/ F/W UP xx.x.x/ F/W UP Vxxx

:Enables PANDORA in source

selection.;

OFF

:Disables.

:Enables AUX in source selection.;

OFF

:Disables.

( 11)

:Automatically distinguishes between audio file disc and music CD.; to play as an music CD. No sound can be heard if an audio file disc is played.

YES

:Starts upgrading the firmware.;

:Cancels (upgrading is not activated). For details on how to update the firmware, see: www.kenwood.com/cs/ce/

( 11)

: Forces

DIGITAL RADIO (DAB)

About DAB (Digital Audio Broadcasting)

DAB is one of the digital radio broadcasting systems available today. It can deliver digital quality sound without any annoying interference or signal distortion. Furthermore, it can carry text, pictures and data. In contrast to FM broadcast, where each program is transmitted on its own frequency, DAB combines several programs (called “services”) to form one “ensemble.” The “primary component” (main radio station) is sometimes accompanied by a “secondary component” which can contain extra programs or other information.

Start listening

Press B SRC to select DAB.

1 2 Press J BAND repeatedly (or press #FM+ on RC-406) to select DB1/ DB2/ DB3. 3 Press and hold S / T (or press and hold S / T(+) on RC-406) to search for an

ensemble.

4 Press S / T (or press S / T(+) on RC-406) to select an ensemble, service or

component to listen.

• To change the tuning method for S / T: Press K SEEK repeatedly. AUTO1: Press S / T: Select an ensemble, service or component. Press and hold S / T: Automatically search for an ensemble. AUTO2: Press S / T: Search for a preset service. MANUAL: Press S / T: Select an ensemble, service or component. Press and hold S / T: Manually search for an ensemble.

Preparation:

1 Connect a DAB antenna to the DAB

antenna jack.

( 25)

2 Press B SRC to select DAB. 3 Press and hold to start the Service

List update.

“LIST UPDATE” appears and update

starts. “UPDATED” appears when update completes.

Updates take up to 3 minutes. No

interruption (such as traffic information) is possible during updates.

• To cancel the Service List update: Press and hold

again.

ENGLISH |

DIGITAL RADIO (DAB)

• To store a service: Press and hold one of the number buttons (1to6).

• To select a stored service: Press one of the number buttons (1to6) (or press one of the number buttons (1to6) on RC-406).

Select a service

Press to enter Service Search mode.

1 2 Turn the volume knob or press J / K to select a service, then

press the knob.

(or using RC-406)

Press J / K to search for a service.

To cancel the Service Search mode, press

Select a service by name

Press to enter Service Search mode.

1 2 Turn the volume knob quickly to enter Alphabet Search

mode.

3 Turn the volume knob or press S / T to select the

character to be searched for.

Press J / K to go to the previous/next page.

4 Press the volume knob to start searching. 5 Turn the volume knob to select a service, then press the knob.

To cancel the Alphabet Search mode, press .

Replay

Press and hold K SEEK (or press K on RC-406).

“REPLAY MODE” appears and replay starts from the live position. You can replay a certain length of time of the current service (depending on the audio bit rate).

During Replay...

• To pause or resume playback, press 6 IW (or press ENT IW on RC-406).

• To skip the current song backward/forward, press S / T (or press S / T(+) on RC-406).

• To rewind/fast-forward, press and hold S / T (or press and hold S / T(+) on RC-406).

• To exit from Replay and go to live, press and hold K SEEK (or press and hold K on RC-406).

Other settings

Press the volume knob to enter

[FUNCTION]

2 Turn the volume knob to make a selection (see the following table), then

press the knob.

3 Press and hold to exit.

To return to the previous setting item or hierarchy, press .

Default:

TUNER SETTING

AF SET

TI ON PTY SEARCH

: While listening to DAB... Automatically switch to FM broadcasting the same program if the DAB signal becomes weak. It will switch back to DAB sound when the signal becomes strong again. While listening to FM... Automatically switch to DAB source broadcasting the same program (if available).;

OFF

:Cancels.

:Allows the unit to temporarily switch to Traffic Information.; Press the volume knob to enter PTY language selection. Turn the volume knob to

select the PTY language ( Selects the available Program Type

ENGLISH/ FRENCH/ GERMAN

( 7)

, then, press

OFF

:Cancels.

), then press the knob.

S / T

to start.

ANALOG RADIODIGITAL RADIO (DAB)

ASW SELECT TRAVEL, WARNINGS, NEWS, WEATHER, EVENT, SPECIAL, RAD INFO,

LIST UPDATE AUTO

PTY WATCH

CLOCK TIME SYNC

• Available Program Type:

SPEECH: NEWS, AFFAIRS, INFO

SCIENCE, VARIED, WEATHER, FINANCE, CHILDREN, SOCIAL, RELIGION, PHONE IN TRAVEL, LEISURE, DOCUMENT MUSIC: POP M CLASSICS, OTHER M

(music)

The unit will search for the Program Type categorized under

[MUSIC]

• If the volume is adjusted during reception of traffic information, announcement or alarm, the adjusted volume is memorized automatically. It will be applied the next time traffic information, announcement or alarm function is turned on.

SPORTS, FINANCE:

the knob. “

” appears in front of the activated announcement type.

Automatically switch from any source to Digital radio ensembles broadcasting an activated announcement type.

•

Multiple announcement can be activated simultaneously.

•

To deactivate, press the volume knob again (“*” goes off).

:Automatically update the DAB Service List when the power is turned

on.;

MANUAL

Automatically switch from any source to Digital Radio ensembles broadcasting a selected type of program.

NEWS, AFFAIRS, INFO, SPORT, EDUCATE, DRAMA, CULTURE, SCIENCE, VARIED, POP M

(music)

, CLASSICS, OTHER M SOCIAL, RELIGION, PHONE IN, TRAVEL, LEISURE, JAZZ, COUNTRY, NATION M



OFF

:Cancels.

:Synchronizes the unit’s time to the Digital Radio signal station time.;

OFF

:Cancels.

(music),

if selected.

Turn the volume knob to make a selection, then press

:Updates the DAB Service List by pressing and holding .

(music)

, ROCK M

(music)

, EASY M

(music)

, WEATHER, FINANCE, CHILDREN,

(music)

, OLDIES, FOLK M

(information),

ROCK M

(music),

JAZZ, COUNTRY, NATION M

(music)

, DOCUMENT

SPORT, EDUCATE, DRAMA, CULTURE

EASY M

(music),

LIGHT M

(music),

(music)

, LIGHT M

(music),

OLDIES, FOLK M

[SPEECH]

Search for a station

Press B SRC to select TUNER.

1 2 Press JBAND repeatedly (or press

select FM1/ FM2/ FM3/ MW/ SW1/ SW2.

AM–/#FM+ on RC-406) to

3 Press S / T (or press S / T(+) on RC-406) to search for a

station.

• To change the searching method for S / T: Press KSEEK

repeatedly. AUTO1: Automatically search for a station. AUTO2: Search for a preset station. MANUAL: Manually search for a station.

• To store a station: Press and hold one of the number buttons

(1to6).

• To select a stored station: Press one of the number buttons (1to6)

(or press one of the number buttons (1to6) on RC-406).

Change the frequency steps

You can change the frequency step of: FM: 50 kHz to 200 kHz MW: 9 kHz to 10 kHz

1 Press and hold B SRC to turn off the power. 2 While pressing number buttons 1 and 5, press B SRC.

Release your fingers from the buttons after the display appears.

• To restore the initial setting, repeat the same procedure.

• When the frequency step is changed, the previously stored stations

in the memory are deleted.

ENGLISH |

ANALOG RADIO

Direct Access Tuning (using RC-406)

Press DIRECT to enter Direct Access Tuning.

1 2 Press the number buttons to enter a frequency. 3 Press ENTIW to search for a station.

• To cancel, press or DIRECT.

• If no operation is done for 10seconds after step is automatically canceled.

2, Direct Access Tuning

Other settings

Press the volume knob to enter

[FUNCTION]

2 Turn the volume knob to make a selection (see the following table),

then press the knob.

3 Press and hold to exit.

To return to the previous setting item or hierarchy, press .

Default:

TUNER SETTING LOCAL SEEK

AUTO MEMORY YES

MONO SET

NEWS SET ON

REGIONAL ON

:Searches only MW/ SW1/ SW2 stations with good reception.;

OFF

:Cancels.

:Automatically starts memorizing 6 stations with good

reception.;

[PRESETTYPE] ON

OFF

control.;

:Cancels. (Selectable only if

.) (

:Improves the FM reception, but the stereo effect may be lost.;

:Cancels.

:The unit will temporarily switch to News Programme if available.;

:Cancels.

:Switches to another station only in the specific region using the “AF”

OFF

:Cancels.

[NORMAL]

is selected for

AF SET ON

TI* ON

PTY SEARCH

•

[MONO SET]/ [NEWS SET]/ [REGIONAL]/ [AF SET]/ [PTY SEARCH]

when the band is FM1/ FM2/ FM3.

• Available Program Type:

SPEECH

: NEWS

SCIENCE IN

MUSIC: POP M (music), ROCK M (music), EASY M (music), LIGHT M (music),

CLASSICS FOLK M (music)

The unit will search for the Program Type categorized under

[MUSIC]

if selected.

• If the volume is adjusted during reception of traffic information, alarm or news bulletin, the adjusted volume is memorized automatically. It will be applied the next time traffic information, alarm or news bulletin function is turned on.

[TI]

in MW/SW1/SW2 band is for enabling traffic interruption to DAB

source only.

: Automatically searches for another station broadcasting the same program in the same Radio Data System network with better reception when the current reception is poor.;

:Allows the unit to temporarily switch to Traffic Information.;

OFF

:Cancels.

Press the volume knob to enter PTY language selection. Turn the volume knob to select the PTY language ( press the knob. Selects the available Program Type (see the following), then, press

S / T

, AFFAIRS

, VARIED

, TRAVEL

to start.

, INFO (information), SPORT

, WEATHER

, LEISURE

, OTHER M (music), JAZZ

, FINANCE

, DOCUMENT

OFF

: Cancels.

ENGLISH/ FRENCH/ GERMAN

, EDUCATE

, CHILDREN

, SOCIAL

, COUNTRY

, NATION M (music), OLDIES

is selectable only

, DRAMA

, RELIGION

), then

, CULTURE

, PHONE

[SPEECH]

CD / USB / iPod

Start playback

The source changes automatically and playback starts.

USB

iPod/iPhone

Press 5 iPod to select the control mode while in iPod source.

MODE ON: MODE OFF:

Label side

USB input terminal

USB cable from the rear of the unit

USB input terminal

and/ or

USB cable from the rear of the unit

KCA-iP102 (optional accessory) or accessory cable of the iPod/iPhone

From the iPod

From the unit.

Eject disc

CA-U1EX (max.: 500mA) (optional accessory)

and/ or

To Do this

Pause or resume

Press 6 IW (or press ENT IW on RC-406).

playback

Select a track/file

Select a folder

Reverse/Fast-forward

Repeat play

Press S / T (or press S / T(+) on RC-406).

Press J / K (or press

AM– / #FM+ on RC-406).

Press and hold S / T (or press and hold S / T(+) on RC-406).

Press 4 repeatedly.

• Audio CD: TRACKREPEAT, REPEATOFF

• MP3/WMA/WAV file or iPod: FILEREPEAT, FOLDERREPEAT, REPEATOFF

• KENWOOD Music Editor Light (KME Light)/ KENWOOD Music Control

Random play

(KMC) file

Press 3 repeatedly.

( 18)

: FILEREPEAT, REPEATOFF

• Audio CD: DISCRANDOM, RANDOMOFF

• MP3/WMA/WAV file or iPod or KME Light/ KMC file: FOLDERRANDOM, RANDOMOFF

Press and hold 3 to select “ALLRANDOM”.

Do not leave the cable inside the car when not using.

You can still play/pause, file skip, fast-forward or reverse files from the unit.

Only for MP3/WMA/WAV files. This does not work for iPod.

For iPod: Applicable only when

For CD: Only for MP3/WMA files.

[MODE OFF]

is selected.

If you connect the iPod/iPhone to the USB input terminal of the unit (while listening to TuneIn Radio, TuneIn Radio Pro or Aupeo), the unit will output the sound from these apps.

ENGLISH |

+ 19 hidden pages