KENWOOD KDC-108 User Manual

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety.

Kenwood Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI TOKYO, JAPAN

KENWOOD CORP. CERTIFIES THIS EQUIPMENT CONFORMS TO DHHS REGULATIONS N0.21 CFR.

1040. 10, CHAPTER 1, SUBCHAPTER J.

Location : Top Panel

FCC WARNING

This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

FCC NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

This symbol mark indicates that Kenwood manufactured this product so as to decrease harmful influence on the environment.

KDC-148 KDC-108 KDC-MP148CR

CD-RECEIVER

INSTRUCTION MANUAL

AMPLI-TUNER LECTEUR DE CD

MODE D’EMPLOI

REPRODUCTOR DE DISCOS COMPACTOS RECEPTOR DE FM/AM

MANUAL DE INSTRUCCIONES

Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new CD-receiver.

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for information or service on the product. Model KDC-148/ KDC-108/ KDC-MP148CR Serial number

US Residents Only

CONTENTS

Safety

Safety 2

Preparation 3

How to attach/detach the faceplate How to reset your unit How to prepare the remote controller

(RC-405)

Basic operations 4

Getting started 6

Canceling the display demonstration Setting the demonstration mode Adjusting the clock Initial settings before operations

Listening to the radio 7

Adjust [SETTINGS] mode settings

Listening to a disc 8

Selecting Repeat Play Selecting Random Play Selecting Scan Play Selecting a folder/track/file Direct Music Search using the remote

controller (RC-405)

Listening to the other external components 9

Function settings 10

Troubleshooting 11

Installation/connection 12

Basic procedure Warning Caution Wiring connection Installing the unit

Specifications 15

WARNING

Stop the car before operating the unit.

Important to know...

To prevent a short circuit, never put or

leave any metallic objects (such as coins or metal tools) inside the unit.

Caution: Adjust the volume so that you

can hear sounds outside the car. Driving with the volume too high may cause an accident.

Condensation: When the car is air-

conditioned, moisture may collect on the laser lens. This may cause disc read errors. In this case, remove the disc and wait for the moisture to evaporate.

This unit can only play the CDs with:

The illustrations in this manual are

examples used to explain more clearly how the controls are used. Therefore, what appears on the illustrations may differ from what appears on the actual equipment.

If you experience problems during

installation, consult your Kenwood dealer.

When you purchase external components,

check with your Kenwood dealer to make sure that they work with your model and in your area.

Detailed information and notes about the

playable audio files are stated in an online manual on the following site: www.kenwood.com/cs/ce/audiofile/

Preparation

How to attach/detach the faceplate

Do not expose the faceplate to direct

sunlight, excessive heat, or humidity. Also avoid places with too much dust or the possibility of water splashing.

Keep the faceplate in its casing while

detached.

The faceplate is a precision piece of

equipment and can be damaged by shocks or jolts.

To prevent deterioration, do not touch the

terminals of the unit and faceplate with your fingers.

How to reset your unit

If this unit fails to operate properly, press the reset button.

The unit returns to factory settings when the reset button is pressed.

Reset button

Discs that cannot be used

Discs that are not round. Discs with coloring on the recording

surface or discs that are dirty.

You cannot play a Recordable/ReWritable

disc that has not been finalized. (For the finalization process refer to your disc writing software, and your disc recorder instruction manual.)

3-inch CD cannot be used. Attempt

to insert using an adapter can cause malfunction.

How to prepare the remote controller (RC-405)

When you use the remote controller for the first time, pull out the insulation sheet.

If the effectiveness of the remote controller decreases, replace the battery.

CALIFORNIA, USA ONLY

This perchlorate WARNING applies only to the product sold or distributed in California USA “Perchlorate Material–special handling may apply, See www.dtsc.ca.gov/ hazardouswaste/perchlorate.”

Caution:

Do not set the remote control in hot places

such as on the dashboard.

Lithium battery.

Danger of explosion if the battery is

incorrectly replaced. Replace only with the same or equivalent type.

The battery pack or batteries shall not be

exposed to excessive heat such sunshine, fire or the like.

Keep battery out of reach of children and in

original package until ready to use. Dispose of used batteries promptly. If swallowed contact physician immediately.

Remote controller (RC-405) is equipped for KDC-148/ KDC-MP148CR.

Insulation sheet

ENGLISH

Basic operations

Remote sensor

Do not expose to bright sunlight.

Volume knob

Detaches the faceplate

The following indicator lights up when...

ST: A stereo broadcast is received (FM). IN: A disc is in the unit.

Loading slot

Ejects the disc

Display window

Auxiliary input jack

Maintenance

Cleaning the unit: Wipe off the dirt on the panel with a dry silicon or soft cloth. Failure to observe this precaution may result in damage to the monitor or unit.

Cleaning the connector: Wipe off dirt on the connector of the unit and faceplate. Use a cotton swab or cloth.

Handling discs

Do not touch the recording surface of the disc. Do not stick tape etc. on the disc, or use a disc with tape stuck on it. Do not use any accessories for the disc. Clean from the center of the disc and move outward. Clean the disc with a dry silicon or soft cloth. Do not use any solvents. When removing discs from this unit, pull them out horizontally. Remove the rims from the center hole and disc edge before inserting a disc.

When you press or hold the following button(s)...

Main unit

SRC

Volume knob

(turn)

Volume knob

(press)

BAND

¢4

SCRL DISP —

— AUD Enters [AUDIO CTRL] settings directly.

— ATT

Remote

controller

—

SRC

VOL

ENT

— Enters [FUNCTION] settings.

AM– /

#FM+

ENT Pauses/resumes playback of a disc.

—

EXIT

Turns on. Turns off if pressed and held.

Selects the available sources (TUNER, CD, AUX, STANDBY), if the power is turned on.

• If the source is ready, playback also starts. “CD” is selectable only

when a disc is loaded.

Adjusts the volume level.

∞ Selects items.

Confirms selection.

Selects the FM bands (FM1/ FM2/ FM3) or AM. Selects the next/previous folder. (Pressing BAND on the main

unit can only select the next folders.)

Mutes the sound while listening to a radio or an external component connected to the auxiliary input jack.

Searches for a radio station.

Selects track/file.

Fast-forwards/reverses tracks if pressed and held. (Fast-

forwards cannot be performed using the remote controller.)

Changes the display information. Scrolls the display information if pressed and held. Enters clock adjustment mode directly (page 6) if pressed and

held while in clock display screen.

Attenuates the sound.

• To return to the previous level, press the button again. Returns to the previous item. Exit from setting mode.

• Press and hold

mode.

General operation

on the main unit will also exit from the setting

ENGLISH

Muting upon the reception of a phone call

To use this feature, connect the MUTE lead to your telephone using a commercial telephone accessory. (page 13)

When a call comes in, “CALL” appears.

The audio system pauses. To continue listen to the audio system during

a call, press SRC. “CALL” disappear and the audio system resumes.

When a call ends, “CALL” disappear.

The audio system resumes.

Getting started

Canceling the display demonstration

The display demonstration is always turned on unless you cancel it.

When you turn on the power (or after you reset the unit), the display shows: [CANCEL

[YES] is selected as the initial setup.

[DEMO OFF] appears.

If no operation is done for about

DEMO] \ [PRESS] \

[VOLUME KNOB]

Press the volume knob.

Press the volume knob again to confirm.

15 seconds or if you turn the volume knob to select [NO] in step 2, [DEMO MODE] appears and the display demonstration starts.

Adjusting the clock

Press the volume knob to enter [FUNCTION] mode.

Turn the volume knob to select [SETTINGS], then press to enter.

Turn the volume knob to select [CLOCK], then press to enter.

Press the volume knob to select [CLOCK ADJ], then press to enter.

Clock hour flashes on the display.

Turn the volume knob to adjust the hour, then press to enter minute adjustment.

Clock minutes flashes on the display.

Turn the volume knob to adjust the minute, then press to confirm.

Press 4

hour and minute adjustment.

Hold to finish the procedure.

¢ to move between the

Setting the demonstration mode

Press the volume knob to enter [FUNCTION].

Turn the volume knob to select [DEMO MODE], then press to enter.

Turn the volume knob to select [ON] or [OFF].

If [ON] is selected, display demonstration

starts if no operation is done for about 20 seconds.

Hold to finish the procedure.

Item Selectable setting (Preset: *)

PRESET TYPE NORM *: Memorizes one station for each preset button in each band (FM1/ FM2/ FM3/ AM). ;

MIX: Memorizes one station for each preset button regardless of the selected band (FM1/ FM2/ FM3/ AM).

KEY BEEP ON */ OFF: Activates/deactivates the keypress tone.

BUILTIN AUX ON1 *: Outputs sound of the connected external component when “AUX” is selected as the source. ;

ON2: Outputs sound from the connected external component when “AUX” is selected as the source. When you

turn on the power, the sound attenuates (to prevent noise when no external component is connected). Turn the volume knob clockwise to return to the previous volume level. ; OFF: Disables “AUX” in source selection.

CD READ 1 *: Automatically distinguishes between audio file disc and music CD. ; 2:

SWITCH PRE REAR */ SUB-W: Selects whether rear speakers or a subwoofer are connected to the line out terminals on the

SP SELECT OFF */ 5/4/ 6 × 9/6/ OEM: Selects the speaker size for optimum performance.

rear of the unit (through an external amplifier).

Initial settings before operations

Press SRC to enter [STANDBY] mode.

Press the volume knob to enter [FUNCTION] mode.

Turn the volume knob to select [INITIAL SET], then press to enter.

Turn the volume knob to make a selection, then press to confirm.

See table below for selection.

Hold to finish the procedure.

Forces to play as a music CD.

Listening to the radio

Hold for about 2 seconds to memorize the current station.

Press briefly to recall memorized station.

Press SRC to select “TUNER.”

Press BAND repeatedly to select a band (FM1/ FM2/ FM3/ AM).

Press 4

Adjust [SETTINGS] mode settings

While listening to the radio...

Press the volume knob to enter [FUNCTION] mode.

Turn the volume knob to select [SETTINGS], then press to enter.

Turn the volume knob to make a selection, then press to confirm.

See table below for selection.

Hold to finish the procedure.

SEEK MODE Selects the tuning mode for 4 / ¢ buttons.

AUTO MEMORY YES: Automatically starts memorizing 6 stations with good reception. ; NO *:

MONO SET ON: Improves the FM reception (but the stereo effect may be lost). ; OFF *: Cancels (stereo effect resumes).

¢ to search for a station.

Item Selectable setting (Preset: *)

AUTO1 *: Automatically search for a station. ; AUTO2: Search in the order of the stations in the preset memory. ; MANUAL: Manually search for a station.

memorizing is not activated). (Selectable only if [NORM] is selected for [PRESET TYPE].) (page 6)

Cancels (automatic

ENGLISH

Using the remote controller (RC-405) FM+ / AM– : Selects band. 4 / ¢ ( + ) : Selects station. 1 – 6 : Selects preset station.

Listening to a disc

Ejects the disc. (“NO DISC” appears and “IN” indicator goes off.)

Press to select track/file. Hold to fast-forwards/reverses.

Press to select next folder.

Press SRC to turn on the power.

Insert a disc into the loading slot.

Playback starts automatically.

Press to resume/pause playback (if necessary).

Selecting Repeat Play

Press number button 4 (REP) repeatedly to make a selection.

Audio CD : TRAC (track) REPEAT,

REPEAT OFF

MP3/WMA : FILE REPEAT, FOLD (folder)

REPEAT, REPEAT OFF

Selecting Random Play

Press number button 3 (ALL RDM) repeatedly to make a selection.

Audio CD : DISC RANDOM, RANDOM OFF MP3/WMA : FOLD (folder) RANDOM,

ALL RANDOM, RANDOM OFF

Press and hold number button

3 (ALL RDM) to select “ALL RANDOM” only if “RANDOM OFF” is selected initially.

Selecting Scan Play

Press number button 2 (SCAN) repeatedly to make a selection.

Audio CD : TRAC (track) SCAN, SCAN OFF MP3/WMA : FILE SCAN, SCAN OFF

If scan play is selected, the unit starts

playing the first 10-second intro of the music in the disc or the current folder. If “SCAN OFF” is selected, the unit resumes normal play of the current song.

Selecting a folder/track/file

Press to enter Music Search mode.

“SEARCH” appears, then the current file

name appears on the display.

Turn the volume knob to select a folder/ track/file, then press to confirm.

To return to the root folder (or first track for

audio CD), press BAND. To return to the previous folder, press . To cancel the Music Search mode, press

and hold . < or > on the display indicates that

preceded/next folder is available.

Direct Music Search using the remote controller (RC-405)

• Not available if Random Play or Scan Play is

selected.

Press DIRECT to enter Direct Music Search Mode.

“– – –” appears.

Press the number buttons to enter the track number.

Press 4 / ¢ to search for the music.

To cancel the Direct Music Search Mode,

press or EXIT.

About Audio file

Playable Audio file: MP3 (.mp3), WMA (.wma) Playable disc media: CD-R/RW/ROM

Playable disc file format: ISO 9660 Level 1/2, Joliet, Romeo, Long file name. Although the audio files are complied with the standards listed above, the play maybe impossible depending on the types or conditions of media or device.

Using the remote controller (RC-405)

In playback mode: FM+ / AM– : Selects folder.

4 / ¢ ( + ) : Selects track/file. ENT : Pauses/resumes playback.

In Music Search Mode: ENT : Confirms selection.

5 / ∞ : Selects folders/files.

: Returns to the previous folder.

Listening to the other external components

Preparation : Make sure [ON1] or [ON2] is selected for [BUILTIN AUX]. (page 6)

Auxiliary input jack

ENGLISH

3.5 mm (3/16") stereo mini plug (optional accessory)

Press SRC to select “AUX.”

Turn on the external component and start playing.

Turn the volume knob to adjust the volume.

Portable audio device (optional accessory)

Function settings

Press the volume knob to enter [FUNCTION] mode.

Turn the volume knob to select [AUDIO CTRL] or [SETTINGS], then press to enter.

Turn the volume knob to make a selection, then press to confirm.

See table below for selection. Repeat step 3 until the desired item is selected/activated.

Press to return to the previous item.

Hold to finish the procedure.

[AUDIO CTRL] : While listening to any source except in STANDBY state...

Item Selectable setting (Preset: *)

SUB-W LEVEL –15 — +15 (Preset: 0): Adjusts the subwoofer output level.

BASS BOOST B.BOOST LV1 */ B.BOOST LV2: Selects your preferred bass boost level. ; OFF:

SYSTEM Q NATURAL */ USER/ ROCK/ POPS/ EASY/ TOP40/ JAZZ/ GAME: Selects a preset sound mode suitable to the

music genre. (Selects [USER] to use the customized bass, middle, and treble settings.)

BASS LEVEL –8 — +8 (Preset: 0):

MID LEVEL

TRE LEVEL

BALANCE L15 — R15 (Preset: 0): Adjusts the left and right speaker output balance.

FADER R15 — F15 (Preset: 0): Adjusts the rear and front speaker output balance.

SUB-W SET ON *: Turns on the subwoofer output. ; OFF:

DETAIL SET LPF SUB-W: THROUGH *: All signals are sent to the subwoofer. ; 85HZ/ 120HZ/ 160HZ: Frequencies

[SUB-W LEVEL/ SUB-W SET/ LPF SUB-W/ SUB-W PHASE] is selectable only if [SWITCH PRE] is set to [SUB-W]. (page 6) [SUB-W LEVEL/ LPF SUB-W/ SUB-W PHASE] is selectable only if [SUB-W SET] is set to [ON].

[SETTINGS]

AUX NAME AUX */ DVD/ PORTABLE/ GAME/ VIDEO/ TV: Selects the desired name for the connected component.

CLOCK CLOCK ADJ: (For details, see page 6.)

DISPLAY DIMMER SET: ON: Dims the display illumination. ; OFF *: Cancels.

adjustment, select the source you want to adjust.)

SUB-W PHASE: REV

SUPREME SET: ON *: Creates realistic sound by interpolating the high-frequency components that are lost

VOL OFFSET: (Preset: 0)

Item Selectable setting (Preset: *)

(Selectable only if “AUX” is selected as the source.)

TEXT SCROLL: AUTO */ ONCE: Selects to scroll the display information automatically, or scroll only once. ;

Source tone memory: Adjusts the level to memorize in each source. (Before making an

Cancels.

higher than 85 Hz/ 120 Hz/ 160 Hz are cut off.

(180°)/ NORM (0°) *: Selects the phase angle of the subwoofer output to be in line with the speaker output for optimum performance. (Selectable only if a setting other than [THROUGH] is selected for [LPF SUB-W].)

in MP3/WMA audio compression. ; OFF: Cancels. (Selectable only when playback an MP3/ WMA disc.)

–8 — +8 (for AUX) ; –8 — 0 (for other sources) each source. The volume level will automatically increase or decrease when you change the source. (Before making an adjustment, select the source you want to adjust.)

OFF: Cancels.

Cancels.

Presets the volume adjustment level of

Troubleshooting

Symptom Remedy/Cause

Sound cannot be heard. Adjust the volume to the optimum level.

Check the cords and connections.

“PROTECT” appears and no operations can be done.

The unit does not work at all. Reset the unit.

Radio reception is poor. Static noise while listening to the radio.

“IN” flashes. The CD player is not operating properly. Reinsert the disc properly. If the condition

CD-R/CD-RW cannot be played back and tracks cannot be skipped.

Disc sound is sometimes interrupted.

“NA FILE” appears. The unit is playing an unsupported audio file.

“NO DISC” appears. Insert a playable disc into the loading slot.

“TOC ERROR” appears. The CD is quite dirty. / The CD is upside-down. / The CD is scratched a lot. Try

“ERROR 99” appears. The unit is malfunctioning for some reason. Press the reset button on the unit. If

“COPY PRO” appears. A copy-protected file is played.

Noise is generated. Skip to another track or change the disc.

Tracks cannot play back as you have intended them to play.

“READING” keeps flashing. Longer readout time is required. Do not use too many hierarchies and folders.

Elapsed playing time is not correct. This is caused by how the tracks are recorded.

Correct characters are not displayed (e.g. album name).

Check to be sure the terminals of the speaker leads are covered with insulating tape properly, then reset the unit. If “PROTECT” does not disappear, consult your nearest service center.

Connect the antenna firmly. Pull the antenna out all the way.

did not improve, turn off the unit and consult your nearest service center.

Insert a finalized CD-R/CD-RW (finalize with the component which you used for recording).

Stop playback while driving on rough roads. Change the disc. Check the cords and connections.

another disc instead.

the “ERROR 99” code does not disappear, consult your nearest service center.

Playback order is determined when files are recorded.

This unit can only display letters (upper case), numbers, and a limited number of symbols.

ENGLISH

Installation/connection

Part list:

A Faceplate.............................................................. (×1)

B Escutcheon ......................................................... (×1)

C Mounting sleeve ............................................. (×1)

D Casing for faceplate

(KDC-148/ KDC-MP148CR only)

E Wiring harness .................................................. (×1)

F Removal tool ..................................................... (×2)

G Flat head screw (for Nissan cars) ........... (×4)

H Round head screw (for Toyota cars) .... (×4)

.......................... (×1)

Basic procedure

Remove the key from the ignition switch, then disconnect the · terminal of the car battery.

Make proper input and output wire connections. \ “Wiring connection” (page 13)

Install the unit to your car. \ “Installing the unit” (page 14)

Reconnect the · terminal of the car battery.

Reset the unit. (page 3)

Warning

The unit can only be installed in a car with

a 12 V DC power supply, negative ground.

If you connect the ignition wire (red) and

the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box.

Disconnect the battery's negative terminal

and make all electrical connections before installing the unit.

Insulate unconnected wires with vinyl tape

or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals.

Be sure to ground this unit to the car's

chassis again after installation.

Caution

If your car's ignition does not have an ACC

position, connect the ignition wires to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die.

Do not use your own screws. Use only the

screws provided.

Install this unit in the console of your

vehicle. Make sure the faceplate will not hit the lid of the console (if any) when closing and opening.

After the unit is installed, check whether

the brake lamps, blinkers, wipers, etc. on the car are working properly.

Mount the unit so that the mounting angle

is 30° or less.

If the fuse blows, first make sure the wires

aren't touching to cause a short circuit, then replace the old fuse with one with the same rating.

Connect the speaker wires correctly to the

terminals to which they correspond. The unit may be damaged or fail to work if you share the · wires or ground them to any metal part in the car.

When only two speakers are being

connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear).

Do not touch the metal part of this unit

during and shortly after the use of the unit. Metal part such as the heat sink and enclosure become hot.

Mounting and wiring this product requires

skills and experience. For safety's sake, leave this work to professionals.

If you experience problems during

installation, consult your Kenwood dealer.

Wiring connection

Rear/subwoofer output terminals

Antenna terminal

White White/Black Gray Gray/Black

Green Green/Black

Purple Purple/Black

Blue (Motor antenna control wire)

Blue/White (Power control wire)

Brown (Mute control wire)

Fuse (10 A)

To front speaker (left)

To front speaker (right)

To rear speaker (left)

To rear speaker (right)

(Not used)

To the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle.

To the terminal that is grounded when either the telephone rings or during conversation. (To connect the Kenwood navigation system, consult your navigation manual.)

ENGLISH

Red (Ignition wire)

Yellow (Battery wire)

Black (Ground wire)

To the metallic body or chassis of the car

Car fuse box

Ignition key switch

Car fuse box

Battery

+ 30 hidden pages