Kenmore 665.16572, 665.16574, 665.16579, 665.17572, 665.17574 Owner's Manual

...
0 (0)
®
ULTRA WASH® Dishwasher
Use & Care Guide
Lavavajillas ULTRA WASH
®
Manual de uso y cuidado
®
Lave-vaisselle ULTRA WASH
Guide d’utilisation et d’entretien
665.17572, 665.17574, 665.17579
8528907
Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Sears Canada, Inc., Toronto, Ontario, Canada M5B 2B8
www.sears.com
www.sears.ca
TABLE OF CONTENTS
WE SERVICE
WE SERVICE WHAT WE SELL......................................................2
WARRANTY.....................................................................................3
DISHWASHER SAFETY..................................................................4
Before Using Your Dishwasher ....................................................5
PARTS AND FEATURES ................................................................6
ULTRA WASH
smartwash
START-UP GUIDE ..........................................................................8
Using Your New Dishwasher........................................................8
DISHWASHER LOADING...............................................................8
Loading Suggestions....................................................................8
Loading Top Rack ........................................................................9
Loading Bottom Rack ............................................................... 10
Loading Silverware Basket........................................................ 10
DISHWASHER USE .................................................................... 11
Detergent Dispenser.................................................................. 11
Rinse Aid Dispenser .................................................................. 12
Dishwasher Efficiency Tips ....................................................... 12
Control Panel............................................................................. 13
Cycle Selection Charts.............................................................. 13
Canceling a Cycle...................................................................... 14
Changing a Cycle or Setting ..................................................... 14
Adding Items During a Cycle..................................................... 14
Option Selections...................................................................... 14
Cycle Status Indicators ............................................................. 16
Active Vent................................................................................. 16
Drying System ........................................................................... 16
Overfill Protection Float............................................................. 16
WASHING SPECIAL ITEMS........................................................ 16
DISHWASHER CARE................................................................... 17
Cleaning..................................................................................... 17
Drain Air Gap ............................................................................. 17
Storing ....................................................................................... 17
TROUBLESHOOTING.................................................................. 18
®
Soil Removal System Featuring
™ Sensing System .................................................7
WHAT WE SELL
Your purchase has added value because you can depend on Sears HomeCentral specialists and access to over 4.2 million parts and accessories, we have the tools, parts, knowledge and skills to ensure our pledge: We Service What We Sell.
Sears Maintenance Agreements
You r K en mo re® appliance is designed, manufactured and tested to provide years of dependable operation. Yet any major appliance may require service from time to time. The Sears Maintenance Agreement offers you an outstanding service program, affordably priced.
The Sears Maintenance Agreement
Is your way to buy tomorrow’s service at today’s price.
Eliminates repair bills resulting from normal wear and tear.
Provides for non-technical and instructional assistance.
Even if you don’t need repairs, provides an annual Preventive Maintenance Check, at your request, to ensure that your appliance is in proper running condition.
Some limitations apply. For more information, call 1-800-827-6655.
For information concerning Sears Canada Maintenance Agreements, call 1-800-361-6665.
®
for service. With over 12,000 trained repair
2
WARRANTY
WARRANTY RESTRICTION
If the dishwasher is subject to other than private family use, the above warranty coverage is effective for only 90 days.
FULL ONE-YEAR WARRANTY ON 1657 AND 1757 SERIES KENMORE ELITE™ DISHWASHERS
For one year from the date of purchase, when this dishwasher is installed and operated according to instructions provided in the Installation Instructions and Use & Care Guide, Sears will repair this dishwasher, free of charge, if defective in material or workmanship.
FULL TWO-YEAR WARRANTY ON ELECTRONIC CONTROL AND POWER SUPPLY BOARD
For two years from the date of purchase, when this dishwasher is installed and operated according to instructions provided in the Installation Instructions and Use & Care Guide, Sears will repair or replace, free of charge, the electronic module and power supply board if defective in material or workmanship.
FULL WARRANTY FOR THE LIFE OF THE DISHWASHER, ON ELITE STAINLESS STEEL TUB MODELS, AGAINST LEAKS IN THE TUB AND INNER DOOR PANEL
For the life of the dishwasher, if a leak should occur as a result of rust-through of the stainless steel tub or inner door panel, Sears will replace free of charge the tub or inner door panel.
LIMITED FIVE-YEAR WARRANTY ON UPPER AND LOWER RACKS
After the first year and until five years from the date of purchase, when the dishwasher is installed and operated in accordance with the instructions provided in the Installation Instructions and Use & Care Guide, Sears will replace parts for the upper or lower dishrack if the rack rusts due to defective materials or workmanship. Customer assumes any labor costs associated with dishrack replacement.
WARRANTY SERVICE
WARRANTY SERVICE IS AVAILABLE BY CONTACTING THE NEAREST SEARS SERVICE CENTER IN THE UNITED STATES OR CANADA. This warranty applies only while the product is in use in the United States or Canada.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state or province to province.
Warranty terms may vary in Canada. For Sears Warranty information in the United States or Canada,
please reference the service numbers located on the back page of this manual.
Sears, Roebuck and Co.
D/817WA, Hoffman Estates, IL 60179
Sears Canada, Inc.
Toronto, Ontario, Canada M5B 2B8
PRODUCT RECORD
In the space below, record your complete model number, serial number, and purchase date. You can find this information on the model and serial number label, located as shown in the Parts and Features section of this book. Have this information available to help you quickly obtain assistance or service when you contact Sears concerning your appliance.
Model number 665.______________________________________________
Serial number___________________________________________________
Purchase date __________________________________________________
Save these instructions and your sales receipt for future reference.
LIMITED TWO-YEAR WARRANTY ON THE ULTRA WASH® WASH SYSTEM
After the first year and until two years from the date of purchase, when the dishwasher is installed and operated in accordance with the instructions provided in the Installation Instructions and Use & Care Guide, Sears will replace any part of the ULTRA WASH ULTRAFLOW™ water feed tube, motor seals and pump gasket) due to defective materials or workmanship. Customer assumes any labor costs associated with replacement of these parts.
®
wash system (motor, pump, spray arms,
3
DISHWASHER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word DANGER or
WARNING. These words mean:
You can be killed or seriously injured if you don't immediately follow instructions.
can be killed or seriously injured if you don't
You follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
4
Before Using Your Dishwasher
Tip Over Hazard Do not use dishwasher until completely installed. Do not push down on open door. Doing so can result in serious injury or cuts.
Electrical Shock Hazard Electrically ground dishwasher. Connect ground wire to green ground connector
in terminal box. Do not use an extension cord. Failure to follow these instructions can result in
death, fire, or electrical shock.
Install where dishwasher is protected from the elements. Protect against freezing to avoid possible rupture of fill valve. Such ruptures are not covered by the warranty. See “Storing” in the “Dishwasher Care” section for winter storage information.
Install and level dishwasher on a floor that will hold the weight, and in an area suitable for its size and use.
Remove all shipping plugs from hoses and connectors (such as the cap on the drain outlet) before installing. See Installation Instructions for complete information.
5
PARTS AND FEATURES
1.
Upper level wash
2.
Utensil basket
3.
Top ra ck
4.
Model and serial number label
5.
Fold-down tines
6.
Bottom rack
7.
Water inlet opening [in tub wall]
Control Panel
ANTI
MART
S
BACTERIAL
WASH
6
POTS
PANS
NORMAL
WASH
HEATING PAUSERINSE AID EMPTY
CHINA
GENTLE
8.
Rack bumper
9.
Heating element
10.
Detergent dispenser
11.
Active vent
12.
Cup shelves
13.
Flexible tines
14.
NO-FLIP™ clips
QUICK
RINSE
HI TEMP
SCRUB
15.
Top spray arm
16.
ULTRA FLOW™ water feed tube
17.
Silverware basket
18.
Lower spray arm
19.
Overfill protection float
20.
ULTRA WASH
21.
Rinse aid dispenser
OPTIONSCYCLES
SANI
RINSE
AIR
DRY
LOCK ON
CLEANSANITIZEDSENSING
DELAY
HOURS
CANCEL
DRAIN
®
module
START
ULTRA WASH® Soil Removal System
Featuring
smartwash
™ Sensing
System
The ULTRA WASH® Soil Removal System gives you sparkling clean dishes, while using less energy and time. The ULTRA
®
Soil Removal System includes:
WASH
A heavy-duty grinder that acts as a food disposer to grind and dispose of large food particles.
An ULTRA WASH® sensor to monitor soil level and adjust the cycles as needed.
An Automatic Temperature Control (ATC) that ensures the proper water temperature for the selected wash cycle, and soil level of the load.
A Triple Action Filtration system that intermittently filters soil from the wash water.
How the ULTRA WASH® Soil Removal System and the Triple Action Filtration System work
1.
Load the dishwasher. Remove bones, large chunks or burned-on food. No rinsing is necessary. Any remaining food soil will be ground up and disposed down the drain with the wash water.
2.
After dishwasher starts, hot water fills the dishwasher to a level near the bottom of the overfill protection float.
3.
When the wash cycle begins, the SENSING indicator glows and the soil level and water temperature are read. During this process, a rotating pattern of lights will appear in the display.
7.
Soils washed from the dishes are filtered from the wash water through the pump system. (See illustration below.)
1
3
1. Soiled water flows into the pump.
2. The water is then pumped into the spray arms.
3. A portion of the pumped water is directed through the filterbox.
Water travels through this system continuously during both wash and rinse cycles.
8.
Once soils collect in the filterbox, they will be sensed and purged. (See 3 above.) The soil is purged by removing only the soils and water in the filterbox. Only a small amount of hot water is removed from the wash cycle. Removing only soiled water conserves water and detergent.
9.
The length of the main wash depends on the soil level sensed and the time needed to reach water temperature.
10.
Once the first rinse begins, fresh hot water enters the dishwasher and sprays onto the dishes. This rinse water is then pumped through the ULTRA WASH System and remaining soil is removed.
11.
The final rinse water is heated with an additional HEATING PAUSE. The rinse aid is dispensed to the water for the final rinse to prepare the dishes for drying.
2
®
Soil Removal
4.
The water drains at the end of the wash cycle or when high soil levels are sensed. Once drained, water fills again near the bottom of the overfill protection float.
5.
As the main wash cycle begins, the SENSING indicator glows while the sensors measure soil load and temperature. Heat will be added during this period until the needed temperature is reached. At this time, the displayed countdown pauses and HEATING PAUSE indicator glows until the needed temperature is reached.
The temperature needed depends on the cycle chosen and the soil level and dishload sensed.
6.
Detergent is dispensed at the correct time in the cycle. The hot water and detergent spray against the soiled surfaces of the load and remove food particles.
How the ULTRA WASH® Sensor and the Automatic Temperature Control (ATC) work
1.
The SENSING indicator glows while the ULTRA WASH Sensors detect the soil level or water temperature in the dishwasher.
2.
After the soil level is determined, unnecessary portions of the cycle are skipped. As this happens, the electronic display pauses or adjusts the cycle display time. This is normal.
3.
The ATC adjusts the water temperature throughout the cycle depending upon the soil level detected. Higher water temperatures are used to improve cleaning with heavier soiled loads.
How the
1.
2.
smartwash
When the indicator glows while the detecting the amount of soil, water temperature, and the size of the dishload in the dishwasher.
After the soil level and dishload size are determined, the sensors automatically adjust the temperature and the amount of water used for the load. This allows less water usage when there is a smaller, less heavily-soiled dishload.
smartwash
™ Sensing System works
™ cycle is started, the SENSING
smartwash
™ Sensors are
®
7
START-UP GUIDE
Before using your dishwasher, remove all packaging materials. Read this entire Use and Care Guide. You will find important safety information and useful operating tips.
Using Your New Dishwasher
1.
Scrape large food soil and hard items (toothpicks or bones) from dishes.
2.
Properly load the dishwasher. (See “Dishwasher Loading.”) Make sure nothing prevents the spray arm(s) from spinning freely.
3.
Add detergent and check the rinse aid dispenser. Add rinse aid if needed. (See “Dishwasher Use.”)
4.
Push door firmly closed. The door latches automatically. Run hot water at the sink nearest your dishwasher until the water is hot. (See “Dishwasher Efficiency Tips.”) Turn off water.
5.
Press the desired cycle and option selections. (See “Dishwasher Use.”) Press START. Or press START to repeat the same cycle and options as the previous cycle.
DISHWASHER LOADING
Loading Suggestions
Remove leftover food, bones, toothpicks and other hard items from the dishes. To conserve water, energy and save time it is not necessary to rinse dishes before putting them in the dishwasher.
NOTE:
Dishes soiled with tomato-based products should be
pre-rinsed to avoid staining. The wash module removes food particles from the water. The
module contains a chopping device which will reduce the size of food items.
NOTE:
enter the wash module, you might hear chopping, grinding, crunching, or buzzing sounds. These sounds are normal when hard items enter the module. Do not let metallic items (such as pot handle screws) get into the wash module. Damage can occur.
For best drying, water must be able to drain from all surfaces.
It is important for the water spray to reach all soiled surfaces.
Load dishes so they are not stacked or overlapping if possible.
Use special care when loading heavy pots and pans. Heavy items can dent the stainless steel interior of the door if they are dropped or bumped.
Make sure pot lids and handles, pizza pans, cookie sheets, etc., do not interfere with the spray arm rotation.
Conserve water, energy and save time over hand rinsing by running a rinse cycle to keep dishes moist if you do not plan to wash them soon. Foods such as eggs, rice, pasta, spinach, and cooked cereals may be hard to remove if they are left to dry over a period of time.
Place items so open ends face down for best cleaning and draining.
Quiet operating tips
To avoid thumping/clattering noises during operation:
Make sure lightweight load items are secured in the racks.
Make sure pot lids and handles, pizza pans, cookie sheets, etc., do not touch interior walls or interfere with the rotation of the spray arm.
Load dishes so they do not touch one another.
NOTE:
dishwasher operation to prevent noise transfer through drains.
If hard items such as fruit seeds, nuts, and egg shells
For built-in models, keep sink drain plugs closed during
8
Loading Top Rack
The top rack is designed for cups, glasses, and smaller items. Many items, up to 9 in. (22 cm), fit in the top rack. (See recommended loading patterns shown.)
NOTE:
The features on your dishwasher rack may vary from the
drawings shown.
10 place setting
Cup shelves
Fold down the extra shelf on the left or right side of the top rack to hold additional cups, stemware or long items such as utensils and spatulas.
Flexible tines
The row of tines on the left and right sides of the top rack can be adjusted to make room for a variety of dishes.
12 place setting
Place items so open ends face down for cleaning and draining.
Load glasses in top rack only. The bottom rack is not designed for glasses. Damage can occur.
Place cups and glasses in the rows between tines. Placing them over the tines can lead to breakage and water spots.
China, crystal, and other delicate items must not touch each other during dishwasher operation. Damage may occur.
Load lightweight plastic items in the top rack only. Only plastic items marked “dishwasher safe” are recommended.
Load plastic items so the force of the spray does not move them during the cycle.
To avoid chipping, do not let stemware touch other items.
Small bowls, pans, and other utensils can be placed in the top rack. Load bowls in the center section for best stability.
Utensil basket
Use this extra capacity basket in the back of the top rack to hold spatulas, wooden spoons, and similar items.
To adjust the flexible tines
1.
Grasp the tip of the tine that is in the tine holder.
2.
Gently push the tine out of the holder.
3.
Lay the tines down, toward the center of the rack.
No-flip clips (on some models)
The no-flip clips hold lightweight plastic items such as cups, lids, or bowls in place during washing.
To move a clip
1.
Pull the clip up and off the tine.
2.
Reposition the clip on another tine.
9
Loading Bottom Rack
The bottom rack is designed for plates, pans, casseroles, and utensils. Many items, up to 13 in. (33 cm) tall, fit in the bottom rack. (See recommended loading patterns shown.)
NOTE:
The features on your dishwasher rack may vary from the
drawings shown.
10 place setting
Do not load glasses, cups, or lightweight plastic items in the bottom rack. Load small items in the bottom rack only if they are secured in place.
Load plates, soup bowls, etc., between tines.
Overlap the edges of plates for large loads.
Load soup, cereal, and serving bowls in the rack in a variety of ways depending upon their size and shape. Load bowls securely between the rows of tines. Do not nest bowls because the spray will not reach all surfaces.
Fold-down tines
You can fold down one or both rows of tines at the back of the bottom rack.
1.
Grasp the tip of the tine that is in the tine holder.
2.
Gently pull the tine out of the tine holder.
3.
Lay the row of tines down in the rack to make room for larger dishes, bowls, pots, pans or roasters.
Loading Silverware Basket
Load the silverware basket while it is in the bottom rack or take the basket out for loading on a counter or table.
NOTE:
Unload or remove the basket before unloading the racks
to avoid spilling water droplets on the silverware.
Place small items such as baby bottle caps, jar lids, corncob holders, etc., in a covered section. Close the cover to hold small items in place.
12 place setting
Load cookie sheets, cake pans, and other large items at the sides and back. Loading such items in front can keep the water spray from reaching the detergent dispenser.
Secure heavily soiled cookware face down in the rack.
Make sure pot handles and other items do not stop rotation of the spray arm(s). The spray arm(s) must move freely.
Do not load items between the bottom rack and the side of the dishwasher tub because they might block the water inlet opening.
NOTE:
If you have removed the bottom rack for unloading or
cleaning, replace it with the bumpers in front.
Use suggested loading patterns, as shown, to increase washability of your silverware.
This silverware basket can be separated and placed into the bottom rack in several locations. Load silverware in all sections or just one, depending upon your load.
When covers are up, mix items in each section of the basket with some pointing up and some down to avoid nesting. Spray cannot reach nested items.
IMPORTANT:
Always load sharp items (knives, skewers, etc.)
pointing down.
10
To remove a small basket
4
1.
Hold the center basket and one small basket. Slide the small basket forward to release the tabs from the corresponding slots.
2.
Pull the baskets apart.
NOTES:
Do not load silver or silver-plated silverware with stainless steel. These metals can be damaged by contact with each other during washing.
Some foods (such as salt, vinegar, milk products, fruit juices, etc.) can pit or corrode silverware. Run a rinse cycle if you do not have a full load to wash immediately.
Filling the dispenser
1.
If the dispenser cover is closed, open the cover by rotating the cover latch.
2.
Fill the Main Wash section with detergent. See “How much detergent to use.”
3.
Fill the Pre-Wash section, if needed.
4.
Close the dispenser cover.
DISHWASHER USE
Detergent Dispenser
The detergent dispenser has 2 sections. The smaller Pre-Wash section empties detergent into the dishwasher when you close the door.
1
2
1. Cover latch
2. Main Wash section
3. Pre-Wash section
4. Cover
The larger Main Wash section automatically empties detergent into the dishwasher during the wash. (See the “Cycle Selection Charts.”)
Use automatic dishwashing detergent only. Other detergents can produce excessive suds that can overflow out of the dishwasher and reduce washing performance.
Add detergent just before starting cycle.
Store tightly closed detergent in a cool, dry place. Fresh automatic dishwasher detergent results in better cleaning.
NOTE:
Do not use detergent with a rinse cycle.
3
It is normal for the cover to open partially when dispensing detergent.
NOTE:
Use both sections for cycles with 2 washes. Use only the covered section for cycles with 1 wash. See the “Cycle Selection Charts” for more details.
How much detergent to use
The amount of detergent to use depends on the hardness of your water and the type of detergent. If you use too little, dishes won’t be clean. If you use too much in soft water, glassware will etch.
Water hardness can change over a period of time. Find out your water’s hardness by asking your local water department, water softener company, or county extension agent.
Different brands of dishwasher detergent have different amounts of phosphorus for softening water. If you have hard water and use a detergent with a phosphorous content of less than 8.7%, you might need to use more detergent, or use a detergent with a phosphorous content higher than 8.7%.
Water Hardness Amount of Detergent
Soft to Medium Hard Water
0 to 6 grains per gallon
For normally soiled loads
Partially fill the Main Wash section (6 tsp or 30 g)
Fill the Pre-Wash section (4 tsp or 20 g)
NOTE:
Add only 2 tsp or 10 g of detergent to the Pre-Wash section if dishes are pre-rinsed or the water is very soft (0 to 2 grains per gallon).
For heavily soiled loads
Partially fill the Main Wash section (7 tsp or 35 g)
Fill the Pre-Wash section (4 tsp or 20 g)
11
Water Hardness Amount of Detergent
6
5
4
3
2
1
-
-
-
x
a
m
Medium to Hard Water
7 to 12 grains per gallon
For normal and heavily soiled loads
Partially fill the Main Wash section (7 tsp or 35 g)
Fill the Pre-Wash section (4 tsp or 20 g)
Rinse aid setting
The amount of rinse aid released into the final wash can be adjusted. The factory setting is at 2. For most water conditions set the adjuster to 1 or 2. If there are rings or calcium (hard water) spots on dishes, try a higher setting.
Very Hard Water
13 grains per gallon and above
NOTE:
It might be necessary to use the Pots Pans cycle, or a normal cycle with the Hi Temp Scrub option for best wash
For normal and heavily soiled loads
Fill the Main Wash section (8 tsp or 40 g)
Fill the Pre-Wash section (4 tsp or 20 g)
Turn the rinse aid dispenser to a higher setting. See “Rinse Aid Dispenser” later in this section.
performance with very hard water.
NOTE:
Fill amounts shown are for standard powdered detergent. Amounts may vary if you use liquid or concentrated powdered detergent. Follow instructions on the package when using liquid dishwasher detergent or concentrated powdered detergent.
Rinse Aid Dispenser
Rinse aids prevent water from forming droplets that can dry as spots or streaks. They also improve drying by allowing water to drain off of the dishes during the final rinse by releasing a small amount of the rinse aid into the rinse water. Your dishwasher is designed to use a liquid rinse aid. Do not use a solid or bar-type.
Filling the dispenser
The rinse aid dispenser holds 4.8 oz (145 mL) of rinse aid. Under normal conditions, this will last for about three months. You do not have to wait until the dispenser is empty to refill it. Try to keep it full, but be careful not to overfill it.
1.
Make sure the dishwasher door is fully open.
2.
Turn the dispenser knob to the left and lift it out.
To adjust the setting
Remove the dispenser knob, then turn the adjuster inside the dispenser to the desired setting.
Dishwasher Efficiency Tips
Hot water dissolves and activates the dishwashing detergent. Hot water also dissolves grease on dishes and helps glasses dry spot-free. For best dishwashing results, water should be 120°F (49°C) as it enters the dishwasher. Loads may not wash as well if the water temperature is too low. Water that is too hot can make some soils harder to remove and cause certain detergent ingredients not to function. If your water heater is located far from the dishwasher, it may be necessary to run the hot water at the faucet closest to the dishwasher to minimize the amount of cold water in the water line.
To check water temperature
1.
Run hot water at the faucet closest to your dishwasher for at least 1 minute.
2.
Place a candy or meat thermometer in a glass measuring cup.
3.
Check the temperature on the thermometer as the water is running into the cup.
To save water, energy and time, do not rinse dishes before putting them into the dishwasher.
Use a delay feature (on some models) to run your dishwasher during off-peak hours. Local utilities recommend avoiding
3.
Add rinse aid until the indicator window looks full.
4.
Clean up any spilled rinse aid with a damp cloth.
5.
Replace the dispenser knob.
heavy usage of energy at certain times of day.
During the summer, run your dishwasher at night. This reduces daytime heat buildup in the kitchen.
Use a rinse aid to improve drying.
Use cycles or options that add extra heat to the wash or rinse portion of the cycle only when needed.
If your home is equipped with a water softener, you may want to avoid starting the dishwasher during the regeneration of the softener, as this may contribute to poor wash performance.
12
Control Panel
OPTIONSCYCLES
S
MART
WASH
ANTI
BACTERIAL
POTS
PANS
NORMAL
WASH
HEATING PAUSERINSE AID EMPTY
CHINA
GENTLE
QUICK
RINSE
HI TEMP
SCRUB
RINSE
Cycle Selection Charts
Select the wash cycle and options desired. Or press START to use the same cycle and options as the previous cycle.
NOTE:
If the last cycle you completed was a rinse cycle, the dishwasher will run the last full wash cycle and options that you selected when you press Start.
A “●” shows what steps are in each cycle. Temperatures indicate where extra heat is added. Water usage is shown in Display time does not include time spent heating the water to the
required temperatures. The display time is suspended, and the sensing light is on, during these water heating periods.
Use this cycle for all day-to-day soil types when washing full to partial dishloads. During the cycle, the sensors will determine water temperature, wash time, and water amount based on the soil level and the dishload size.
Dish-
Soil
Level
Sensed
Heavy
Light
Heavy
Light
Wash Main
load
Full
Par-
tial
U.S.
Rinse Rinse Final
Wash
140°F
(60°C)
130°F
(54°C)
130°F
(54°C)
120°F
(49°C)
Purge
gallons/liters.
Use both detergent dispenser sections when washing a full soiled dishload.
Use one detergent dispenser section when washing lightly-soiled, partial dishloads.
Heated
Rinse
140°F (60°C)
140°F (60°C)
140°F (60°C)
140°F (60°C)
Dry Time
(min)
95* 8.8-10.1/
87* 6.9/26.2
87* 6.9-8.2/
68* 5.9/22.2
Water Usage (gal/L)
33.3-38.2
26.2-31.0
SANI
CLEANSANITIZEDSENSING
AIR
DRY
LOCK ON
Soil
Level
Sensed
Heavy
Light
Soil
Level
Sensed
Heavy
Light
Soil
Level
Sensed
Heavy
Light
DELAY
HOURS
Wash Main
130°F
(54°C)
130°F
(54°C)
O
Wash Main
130°F
(54°C)
130°F
(54°C)
Wash Main
CANCEL
DRAIN
Use this cycle for all day­to-day soil types, including both normal and heavy soils, giving you exceptional cleaning performance combined with reassuring sanitization.
Rinse Rinse Final
Wash
145°F
(63°C)
145°F
(63°C)
Heated
Rinse
160°F (71°C)
160°F (71°C)
Use this cycle for hard-to­clean, heavily-soiled pots, pans, casseroles, and regular tableware.
Rinse Rinse Final
Wash
140°F
(60°C)
140°F (60°C)
Heated
Rinse
140°F (60°C)
140°F (60°C)
Use this cycle for loads with normal amounts of food soil. (The energy­usage label is based on this cycle.)
Rinse Rinse Final
Wash
140°F
(60°C)
130°F
(54°C)
Heated
Rinse
140°F (60°C)
140°F (60°C)
START
Use both detergent dispenser sections.
Dry Time
Water
(min)
Usage (gal/L)
99* 8.8-10.4/
33.3-39.4
91* 6.9/26.2
Use both detergent dispenser sections.
Dry Time
Water
(min)
Usage (gal/L)
97* 8.8-10.4/
33.3-39.4
89* 6.9/26.2
Use both detergent dispenser sections.
Dry Time
Water
(min)
Usage (gal/L)
95* 8.8-10.1/
33.3-38.2
87* 6.9/26.2
13
Soil
Level
Sensed
Heavy
Light
Use this cycle for china and crystal. This cycle uses a light wash and gentle dry. During the heated dry, the heating element cycles on and off.
Wash Main
Wash
Rinse
or
Purge
Purge
Rinse Final
Use main detergent dispenser section.
Dry Time
cycled
cycled
Heated
Rinse
135°F (57°C)
135°F (57°C)
(min)
Water Usage (gal/L)
79* 7.1-8.6/
26.9-32.6
70* 5.9/22.2
Changing a Cycle or Setting
During the first fill of a cycle
1.
Press a new cycle and/or options.
2.
Check the detergent dispensers. They must be filled properly for the new cycle.
After the first fill of a cycle
1.
Press
Use this rinse cycle for rinsing dishes, glasses, and silverware that will not be washed right away.
Wash Main
*
Cycle time includes dry time. An asterisk ( * ) by the cycle time
Wash
Rinse Rinse Final
Do not use detergent with this cycle.
Heated
Rinse
Dry Time
(min)
Water Usage (gal/L)
10 1.8-2.1/
6.8-7.9
indicates the cycle time might be longer depending on the temperature of the water entering the dishwasher. The cooler the water, the longer the cycle time. If the water is already hot enough, the cycle time will be as shown.
Canceling a Cycle
Anytime during a cycle, press
The display shows
Your dishwasher starts a 2-minute drain (if needed). Let the dishwasher drain completely. The light turns off after 2 minutes.
NOTE:
If your dishwasher does not need draining, the light turns
off. Select a new cycle and options.
To stop the drain
You can press Cancel/Drain again to stop the drain immediately. Remember to drain the dishwasher before starting a new cycle.
To clear the indicators
Press Cancel/Drain before starting the dishwasher to clear all options and cycles.
The display shows
Your dishwasher starts a 2-minute drain (if needed). Let the dishwasher drain completely. The light turns off after 2 minutes.
NOTE:
If your dishwasher does not need draining, the light
turns off.
2.
Check the detergent dispensers. They must be filled properly for the new cycle.
3.
Close the door.
4.
Press a new cycle and/or options.
5.
Press START.
Adding Items During a Cycle
You can add an item anytime before the main wash starts. Open the door and check the detergent dispenser. If the cover is still closed, you can add items.
To add items
1.
Lift up the door latch to stop the cycle. Wait for the spraying action to stop before opening the door.
2.
Open the door. If the detergent dispenser cover is still closed, add the item.
3.
Close the door firmly until it latches. The dishwasher resumes the cycle after about a 5-second pause.
Option Selections
You can customize your cycles by pressing an option. If you change your mind, press the option again to turn the option off, or select a different option if desired.
You can change an option anytime before the selected option begins. For example, you can press an unheated drying option any time before drying begins.
Press START to use the same cycle and option(s) as the previous wash cycle.
NOTE:
If the last cycle you completed was a rinse cycle, when you press Start, the dishwasher runs the last full wash cycle and options.
14
Hi Temp Scrub
LOCK ON
Select this option to increase the target water temperature during the wash portions of the cycle. Hi Temp Scrub raises the target water temperature to 145ºF (63ºC), in the main wash. In the Anti Bacterial and Pots Pans cycles, Hi Temp Scrub also raises the target water temperature to 135°F (57°C) in the pre-wash. Heating the water helps improve washing results. Hi Temp Scrub is useful when loads contain baked-on food.
This option adds heat and wash time to the cycle. When Hi Temp Scrub is used with the Anti Bacterial and Pots Pans cycles, water is also added to the cycle.
NOTE:
Hi Temp Scrub is an option with Anti Bacterial, Pots Pans
and Normal Wash.
Sani Rinse
Select this option to raise the water temperature in the final rinse to approximately 160°F (71°C). Sani Rinse adds heat and time to the cycle. This high temperature rinse sanitizes your dishes and glassware in accordance with NSF Standard 184 for Residential Dishwashers. Certified residential dishwashers are not intended for licensed food establishments.
To turn on the Lock
Press and hold
for 4 seconds. LOCK ON glows.
If you press any pad while your dishwasher is locked, the light flashes 3 times.
To turn off the Lock
Press and hold AIR DRY for 4 seconds. The light turns off.
Delay Hours
Select this option to run your dishwasher at a later time or during off-peak hours. You can add items to the load anytime during the delay countdown. After adding items, close the door firmly until it latches. The delay countdown will not continue if the door is not latched.
You can delay the start of a cycle up to 12 hours.
The first time you use Delay Hours, you will see
NOTE:
The Anti Bacterial cycle automatically uses this option. Sani Rinse is an option with SmartWash, Pots Pans and Normal Wash. Only these sanitization cycles have been designated to meet the NSF requirements.
Air Dry
Select this option to dry without heat. Air drying is useful when loads contain plastic dinnerware that may be sensitive to high temperatures.
LOCK ON
The dishes take longer to dry and some spotting can occur. For best drying, use a liquid rinse aid. Some items (such as plastics) may need towel drying.
NOTE:
Air Dry is an option with all cycles, except Quick Rinse.
Lock On
Use the Lock On to prevent unintended use of the dishwasher. You can also use the lock feature to prevent unintended cycle or option changes during a cycle.
showing a 1-hour delay.
To delay the start
1.
Close the door.
2.
Select a wash cycle and options.
3.
Repeatedly press
until you see the desired hours of delay in the display. When the delay reaches 12 hours, the delay turns off. Press
DELAY HOURS again to select a new number of delay hours.
4.
Press START.
NOTE:
To cancel the delay and cycle, press CANCEL/DRAIN. To cancel the delay and start the cycle immediately, press START again.
IMPORTANT:
Operate your dishwasher only when you are at home.
If your home is equipped with a water softener, do not start the dishwasher during the regeneration of the softener.
LOCK ON
When LOCK ON is lit, all buttons are disabled.
NOTES:
The dishwasher door can be opened while the controls are locked.
You can turn on the Lock while the dishwasher is running.
15
Cycle Status Indicators
Follow the progress of your dishwasher with the Cycle Status indicators.
HEATING PAUSERINSE AID EMPTY
Rinse Aid Empty
Fill the Rinse Aid dispenser when RINSE AID EMPTY is lit. A rinse aid prevents water from forming droplets that can dry as spots or streaks. If the Rinse Aid dispenser is empty, the light glows when you select a cycle or while a cycle is running.
Heating Pause
Your dishwasher adds heat to the water to improve soil removal. The HEATING PAUSE glows while the water is heated to a temperature determined by the cycle chosen and the soil level sensed. When the HEATING PAUSE glows, the countdown display pauses until the needed temperature is reached.
Sensing
Your dishwasher senses the soil level on the dishes. Soil level determines the length of some cycles, the amount of heat added to the wash or rinse, and the cycle needed for the load. SENSING glows during soil sensing, and while water is being heated. Wash action continues while sensing occurs.
Sanitized
If you select the Sani Rinse option, SANITIZED glows when the Sani Rinse cycle is finished. If your dishwasher did not properly sanitize your dishes, the light flashes at the end of the cycle. This can happen if the cycle is interrupted. The light goes off when you open the door.
CLEANSANITIZEDSENSING
Overfill Protection Float
The overfill protection float (in the front right corner of the dishwasher tub) keeps the dishwasher from overfilling. It must be in place for the dishwasher to operate.
Check under the float for objects that may keep the protector from moving up or down.
WASHING SPECIAL
ITEMS
If you have doubts about washing a particular item, check with the manufacturer to see if it is dishwasher safe.
Material Dishwasher Safe?/Comments
Aluminum
Disposable Aluminum
Yes
High water temperature and detergents can affect finish of anodized aluminum.
No
Do not wash throwaway aluminum pans in the dishwasher. These might shift during washing and transfer black marks to dishes and other items.
Clean
CLEAN glows when a cycle is finished. The light turns off when you open the door or press Cancel/Drain.
Active Vent
The Active Vent reduces the sounds from your dishwasher. The cover closes after the cycle starts. Filling and washing sounds are reduced. The Active Vent opens when wash action ends and vapor is vented into room.
NOTE
: There is a slight noise when the cover closes or opens.
This is normal.
Drying System
During drying, you can see steam escaping through the vent at the upper left corner of the door. This is normal as the heat dries your dishes.
IMPORTANT:
during drying.
The vapor is hot. Do not touch the vent
Bottles and Cans
Cast Iron
China/ Stoneware
Crystal
Gold
Glass
No
Wash bottles and cans by hand. Labels attached with glue can loosen and clog the spray arms or pump and reduce washing performance.
No
Seasoning will be removed and iron will rust.
Yes
Always check manufacturer’s recommendations before washing. Antique, hand-painted, or over-the-glaze patterns may fade. Gold leaf can discolor or fade.
Yes
Check manufacturer’s recommendations before washing. Some types of leaded crystal can etch with repeated washing.
No
Gold-colored flatware will discolor.
Yes
Milk glass yellows with repeated dishwasher washing.
16
Hollow-Handle Knives
No
Handles of some knives are attached to the blade with adhesives which can loosen if washed in the dishwasher.
Material Dishwasher Safe?/Comments
Pewter, Brass, Bronze
Disposable Plastics
Plastics
Stainless Steel
No
High water temperatures and detergent can discolor or pit the finish.
No
Cannot withstand high water temperatures and detergents.
Yes
Always check manufacturer’s recommendations before washing. Plastic items may vary in their ability to withstand high temperatures and detergents. It is recommended that light items such as lids and butter dishes be placed in the upper rack only. Sturdy items such as coolers and high-chair trays may be placed in the lower rack. When washing plastic items in the lower rack, it is recommended that the air dry option be used.
Yes
Run a rinse cycle if not washing immediately. Prolonged contact with food containing salt, vinegar, milk products, or fruit juice can damage finish.
Cleaning the interior
Hard water minerals can cause a white film to build up on the inside surfaces, especially just beneath the door area.
Do not clean the dishwasher interior until it has cooled. Wear rubber gloves. Do not use any type of cleanser other than dishwasher detergent because it may cause foaming or sudsing.
To clean interior
Make a paste with powdered dishwasher detergent on a damp sponge and clean.
OR
Use liquid automatic dishwasher detergent and clean with a damp sponge.
OR
See the vinegar rinse procedure in “Spotting and filming on dishes” in “Troubleshooting.”
NOTE:
Run a normal cycle with detergent after cleaning the
interior.
Drain Air Gap
Check the drain air gap anytime your dishwasher isn’t draining well.
Some state or local plumbing codes require the addition of a drain air gap between a built-in dishwasher and the home drain system. If a house drain is clogged, the drain air gap protects your dishwasher from water backing up into it.
Sterling Silver or Silver Plate
Tin
Wooden Ware
Yes
Run a rinse cycle if not washing immediately. Prolonged contact with food containing salt, acid, or sulfide (eggs, mayonnaise, and seafood) can damage finish.
No
Can rust.
No
Wash by hand. Always check manufacturer’s instructions before washing. Untreated wood can warp, crack, or lose its finish.
DISHWASHER CARE
Cleaning
Cleaning the exterior
In most cases, regular use of a soft, damp cloth or sponge and a mild detergent is all that is necessary to keep the outside of your dishwasher looking nice and clean.
The drain air gap is usually located on top of the sink or countertop near the dishwasher. To order a drain air gap, please reference the service numbers located on the back page of this manual. Ask for Part Number 300096.
NOTE:
The drain air gap is an external plumbing device that is not part of your dishwasher. The warranty provided with your dishwasher does not cover service costs directly associated with the cleaning or repair of the external drain air gap.
To clean the drain air gap
Clean the drain air gap periodically to ensure proper drainage of your dishwasher. Follow the cleaning instructions provided by the manufacturer. With most types, you lift off the chrome cover. Unscrew the plastic cap. Then check for any soil buildup. Clean if necessary.
Storing
Storing for the summer
Protect your dishwasher during the summer months by turning off the water supply and power supply to the dishwasher.
Winterizing your dishwasher
Protect your dishwasher and home against water damage due to freezing water lines. If your dishwasher is left in a seasonal dwelling or could be exposed to near freezing temperatures, have your dishwasher winterized by authorized service personnel.
17
TROUBLESHOOTING
First try the solutions suggested here and possibly avoid the cost of a service call...
Dishwasher is not operating properly
Dishwasher does not run or stops during a cycle
Is the door closed tightly and latched? Is the right cycle selected? Refer to the “Cycle Selection
Charts.” Is there power to the dishwasher? Has a household fuse
blown or circuit breaker tripped? Has the motor stopped due to an overload? The motor
automatically resets itself within a few minutes. If it does not restart, call for service.
Is the water shut-off valve (if installed) turned on?
Dishwasher will not fill
Is the overfill protection float able to move up and down freely? Press down to release.
Dishwasher seems to run too long
Is the water supplied to the dishwasher hot enough? The dishwasher runs longer while heating water. Refer to the “Dishwasher Efficiency Tips” section.
A delay automatically occurs in some wash and rinse cycles until the water reaches the proper temperature.
Water remains in the dishwasher
Is the cycle complete?
Detergent remains in the covered section of the dispenser
Is the cycle complete? Is the detergent lump-free? Replace detergent if necessary.
White residue on the front of the access panel
Was too much detergent used? Refer to the “Detergent Dispenser” section.
Is the brand of detergent making excess foam? Try a different brand to reduce foaming and eliminate buildup.
Odor in the dishwasher
Are dishes washed only every 2 or 3 days? Run a rinse cycle once or twice a day until you have a full load.
Condensation on the kitchen counter (built-in models)
Is the dishwasher aligned with the countertop? Moisture from the vent in the dishwasher console can form on the counter. Refer to the Installation Instructions for more information.
Dishes are not completely clean
Food soil left on the dishes
Is the dishwasher loaded correctly? Refer to the “Dishwasher Loading” section.
Is the water temperature too low? For best dishwashing results, water should be 120°F (49°C) as it enters the dishwasher. Refer to the “Dishwasher Efficiency Tips” section.
Did you use the correct amount of fresh detergent? Use recommended dishwasher detergents only. Refer to the “Detergent Dispenser” section. Never use less than 1 tb (15 g) per load. Detergent must be fresh to be effective. Store detergent in a cool, dry area. Heavy soil and/or hard water generally require extra detergent.
Is detergent caked in dispenser? Use fresh detergent only. Do not allow detergent to sit for several hours in a wet dispenser. Clean dispenser when caked detergent is present.
Is the pump or spray arm clogged by labels from bottles and cans? If you wash bottles and cans in your dishwasher, check for labels clogging the pump or spray arm.
Is the home water pressure high enough for proper dishwasher filling? Home water pressure should be 20 to 120 psi (138 to 828 kPa) for proper dishwasher fill. A booster pump on the water supply can be added if pressure is too low.
Are high suds slowing the wash arm? Never use soap or laundry detergents. Use recommended dishwasher detergents only.
Spots and stains on dishes
Spotting and filming on dishes
Is your water hard or is there a high mineral content in your water? Conditioning the final rinse water with a liquid rinse aid helps eliminate spotting and filming. Keep the rinse aid dispenser filled.
Is the water temperature too low? For best dishwashing results, water should be 120°F (49°C) as it enters the dishwasher. Refer to the “Dishwasher Efficiency Tips” section.
Did you use the correct amount of effective detergent? Use recommended dishwasher detergents only. Refer to the “Detergent Dispenser” section. Never use less than 1 tb (15 g) per load. Detergent must be fresh to be effective. Store detergent in a cool, dry area. Heavy soil and/or hard water generally require extra detergent.
18
Loading...
+ 42 hidden pages