JVC XA-F107AUS, XA-F107BE, XA-F107BEF, XA-F107BEV, XA-F107BJ Instructions Manual

...

0 (0)

DIGITAL AUDIO PLAYER

XA-F57A/P/R/S/W XA-F107A/B/H/P/R/S

Thank you for purchasing this JVC product.

Please read these instructions carefully before starting operation to be sure to obtain optimum performance and a longer service life from the unit.

INSTRUCTIONS

LVT1542-004A [J,E,EV]

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

8) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

For qualified service personnel only

CAUTION:

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

IMPORTANT SAFETY INSTRUCTIONS

For U.S.A

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against hamful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

For U.S.A For the main unit:

Declaration of Conformity

Model Number: XA-F57A/P/R/S/W

XA-F107A/B/H/P/R/S Trade Name: JVC Responsible Party: JVC Americas Corp. Address: 1700 Valley Road, Wayne

New Jersey 07470 Telephone Number: 973-317-5000

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION:

Changes or modification not approved by JVC could void the user's authority to operate the equipment.

For Canada:

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

IMPORTANT SAFETY INSTRUCTIONS

Player

• No altering or remodeling

This can cause malfunctioning.

• No dropping or strong impacts

This may damage the player.

• Locations to be avoided

Avoid using the player in the following locations since they can cause malfunctioning.

1. Bathrooms and other moisture-prone places

2. Warehouses and other dusty places

3. Very hot places near heating appliances, etc.

Listening precautions

• Do not play your Headphones at a high volume.

• Hearing experts advise against continuous extended play.

• If you experience a ringing in your ears, reduce volume or discontinue use.

• Do not use while operating a motorized vehicle. It may create traffic hazard and is illegal in many areas.

• You should use extreme caution or temporarily discontinue use in potentially hazardous situations.

• Even if your Headphones are an open-air type designed to let you hear outside sounds, do not turn up the volume so high that you cannot hear what is around you.

• Once you have established a comfortable sound level, leave the level there.

IMPORTANT SAFETY INSTRUCTIONS

Do not leave the player exposed to direct sunlight for long periods of time

This may deform or discolor the player and may also cause malfunctioning.

CAUTION:

Do not place any naked flame sources, such as lighted candles, on the apparatus.

• We have no responsibility for any improper recording or playback incurred by equipment malfunction.

• It is recommended to store backup copy of your important data in your PC or the like.

IMPORTANT SAFETY INSTRUCTIONS

Information for Users on Disposal of Old Equipment

[European Union]

This symbol indicates that the electrical and electronic equipment should not be disposed as general household waste at its end-of-life. Instead, the product should be handed over to the applicable collection point for the recycling of electrical and electronic equipment for proper treatment, recovery and recycling in accordance with your national legislation.

By disposing of this product correctly, you will help to conserve natural resources and will help prevent potential negative effects on the environment and human health which could otherwise be

Attention:

This symbol is only valid in the European Union.

caused by inappropriate waste handling of this product. For more information about collection point and recycling of this product, please contact your local municipal office, your household waste disposal service or the shop where you purchased the product.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

(Business users)

If you wish to dispose of this product, please visit our web page www.jvc-europe.com of the product.

[Other Countries outside the European Union]

If you wish to dispose of this product, please do so in accordance with applicable national legislation or other rules in your country for the treatment of old electrical and electronic equipment.

to obtain information about the take-back

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS ................................................ 2

TABLE OF CONTENTS .......................................................................... 7

GETTING STARTED............................................................................... 8

INSTALLING USB DRIVER (FOR WINDOWS 98SE ONLY) .............. 8

CHARGING THE BUILT-IN BATTERY ................................................ 9

CONNECTING TO PC....................................................................... 10

PARTS OF THE DIGITAL AUDIO PLAYER ...................................... 12

HOW TO USE THE NECK STRAP HEADPHONES ......................... 13

TURNING POWER ON/OFF ............................................................. 15

DISPLAY OVERVIEW ....................................................................... 16

BASIC OPERATIONS........................................................................... 17

USING THE MAIN MENU.................................................................. 17

PLAYING MUSIC .............................................................................. 18

NAVIGATE ........................................................................................ 19

RECORDING MUSIC FROM EXTERNAL AUDIO EQUIPMENT IN

LINE-IN MODE................................................................................ 21

DELETING FILES .............................................................................. 23

ADVANCED FEATURES ...................................................................... 24

SET MENU ITEMS ............................................................................ 24

EQUALIZER....................................................................................... 24

PLAYMODE ....................................................................................... 26

SLEEP TIMER ................................................................................... 28

AUTO POWER OFF .......................................................................... 29

BACKLIGHT....................................................................................... 30

CONTRAST ....................................................................................... 31

RECORD SET ................................................................................... 32

LANGUAGE ....................................................................................... 34

ABOUT .............................................................................................. 35

RESETTING THE UNIT .................................................................... 36

LOCKING BUTTONS (HOLD) ........................................................... 37

DISPOSING OF THE DIGITAL AUDIO PLAYER .............................. 38

TROUBLESHOOTING .......................................................................... 41

SPECIFICATIONS................................................................................. 42

ACCESSORIES ................................................................................. 43

GETTING STARTED

INSTALLING USB DRIVER (FOR WINDOWS 98SE ONLY)

Follow these instructions to load software that enables a computer to recognize the Digital Audio Player.

Make sure that no programs, such as games or anti-virus software, are running on the PC. If programs are open, close and exit from the programs before proceeding.

1. Insert the CD-ROM into the CD-ROM drive of your PC.

2. Turn off the Digital Audio Player and connect it to your PC with the

USB connector.

3. Follow the on-screen instructions to install the driver from the CD-

ROM. On a screen to search for the location of the Digital Audio Player’s driver, click the [Browse] button and select CD-ROM drive and then proceed to the next screen.

4. Be sure that the installation completion screen appears.

5. Reboot the PC.

NOTE

• If you are using Windows XP, Me or 2000, you do not need to install the USB driver on the CD-ROM.

GETTING STARTED

CHARGING THE BUILT-IN BATTERY

Charge the rechargeable battery before using it for the first time or when it is depleted.

Charging the battery using a USB connection

Turn on the PC and connect the player to a USB port on your PC using a USB cable. (Refer to "CONNECTING TO PC" on page 10.) The battery indicator appears in the display, and charging of the battery

starts. During charging the indicator shows " " repeatedly. When charging is completed, " " appears.

NOTES

• It takes approximately 2.5 hours to fully charge an empty battery.

• When your PC is in standby mode, the battery cannot be charged.

• The player cannot be operated while it is being charged.

Notes on the built-in battery:

• To replace the battery, consult your dealer or JVC Service Center.

• To dispose of the player, follow the procedure described in "DISPOSING OF THE DIGITAL AUDIO PLAYER" on page 38 and remove the built-in battery. DO NOT disassemble the player, except when you dispose of it (doing so may cause a failure or breakage).

Battery indicator

The battery indicator shows the remaining battery level. When the battery level becomes low, "Low Battery" appears on the display. In this case, you need to charge the battery.

GETTING STARTED

CONNECTING TO PC

You can transfer MP3 and WMA format music files from the PC to your Digital Audio Player through USB port. USB2.0 (480Mbps speed is not supported.)

For Windows 98SE user:

Before connecting your player to the computer for the first time, you need to install the USB driver from the supplied CD-ROM into your computer. For details, see "INSTALLING USB DRIVER (FOR WINDOWS 98SE ONLY)" on page 8.

Connecting Digital Audio Player to PC

1. Make sure that the player is turned off.

(Press and hold 7 button.)

2. Open the cover of the USB connector.

3. Connect the player to the USB port on your PC using USB cable.

"USB Connected" appears on the display, and the connection is completed.

USB cable (supplied)

GETTING STARTED

Transferring music files from PC to Digital Audio Player

1. Open the player’s folder (removable disk or device) from My

Computer or Explorer.

2. Copy and paste or drag and drop the music files from the PC to the

player’s folder. During copying files, "WRITING" appears on the player's display. After completion, "USB Connected" continuously appears.

NOTE

• When you transfer a WMA-DRM file from the PC, use Windows Media® Player 9 or later. If you transfer it by drag and drop, it cannot be played with the player.

Disconnecting from PC

For Windows 2000/Me/XP users:

Left-click the " " icon in the task bar, and follow the on-screen instructions.

For Windows 98SE users

Open "My Computer" and select "Removable Disk", then right-click to select "EJECT".

• Microsoft, Windows and Windows Media are either trademarks or registered trademarks of Microsoft Corporation in the United States and other countries.

• Other names of systems and products mentioned in these instructions are usually registered trademarks of the manufacturers who developed the system or product concerned.

NOTES

• The player supports MP3 ID3 V1.0, 1.1 tags, ID3 V2.3 tags and WMA tags. ID3 tags and WMA tags are the data including music names and artist names recorded in MP3 files and WMA files.

• When the player is connected to the PC, it is recognized as an external USB memory (removable disk) and shown on the PC. You can treat the player as an external USB memory.

GETTING STARTED

PARTS OF THE DIGITAL AUDIO PLAYER

1234

1 Display 2 4 (Reverse) button 3 3 8 (Play/Pause) button 4 ¢ (Forward) button 5 LINE IN jack

8 Hole for strap 9 Hold switch 0 Reset switch

- 7 (Stop) button = MENU button

-=~!

6 USB connector 7 Headphone jack

~ REC button ! VOL+/- (Volume) buttons

GETTING STARTED

HOW TO USE THE NECK STRAP HEADPHONES

A neck strap with a pair of built in headphones, called "Neck Strap Headphones", has been included for listening to your digital audio player. By wearing the player around your neck using the Neck Strap Headphones, you can enjoy listening to music anywhere you go without having to worry about the cables.

1. Insert the supplied strap through the hole of the player and loop it

through itself. * If you have difficulty in inserting the strap into the hole, use a thin,

sharp tool to push it through.

2. Insert the Neck Strap Headphones' plug into the headphone jack of

the player.

3. Adjust the positions of the silver slider on the Neck Strap

Headphones to make a loop large enough for your head to pass through.

GETTING STARTED

4. Once you are wearing the Neck Strap Headphones around your

neck, bring each earphone from the behind your neck and place in the each ear respectively.

You can also adjust the position of the silver slider according to your preference.

NOTE

• Be sure to read the separate sheet "Precautions for Use of the Neck

Strap Headphones" for its safety information.

GETTING STARTED

TURNING POWER ON/OFF

To turn power ON

Press and hold 3 8 button till "Welcome!" appears. After a while, the

following screen appears.

DIGITAL

AUDIO

PLAYER

To turn power OFF

Press and hold 7 (Stop) button.

GETTING STARTED

DISPLAY OVERVIEW

MUSIC mode

∗ This is not displayed when NORMAL mode is selected. ∗∗ If both the top and the bottom lines of the file information are long, the

top line is scrolled first, and then the bottom line is scrolled.

1 Play indicator 2 Volume level 3 Play mode indicator 4 EQ (sound mode)∗ 5 Sleep Timer icon 6 Lock icon 7 Battery indicator 8 Track number/Total number of

tracks

9 File information∗∗ 0 Track time

- Mode indicator

BASIC OPERATIONS

USING THE MAIN MENU

There are number of modes you can operate using MAIN MENU.

MAIN MENU

MUSIC

Types of modes

MUSIC mode

Select to play music. (See page 18.)

NAVIGATE mode

Select to easily search for the desired music. (See page 19.)

LINE IN mode

Select to record music (MP3 file) from external audio equipment. (See page 21.)

DELETE mode

Select to delete files. (See page 23.)

ABOUT mode

Select to display about the player. (See page 35.)

RESET mode

Select to reset the settings you have made. (See page 36.)

SET mode

Select to set advanced settings. (See pages 24 to

34.)

BASIC OPERATIONS

PLAYING MUSIC

You can play the music files. Before playing music, adjust the volume level with the volume +/- buttons.

Track time (in stop mode) Playback time (during playing)

To play music

1. After turning on the player, press MENU button and ¢ / 4 button

to select MUSIC mode from Main Menu, and then press 3 8 button

to enter that mode.

2. Press 3 8 button

To stop: Press 7 button. To pause: Press 3 8 button.

To select track:

During playback or in stop mode, press ¢ / 4 button.

To fast-forward/reverse track:

During playback, press and hold ¢ / 4 button.

NOTES

• If no audio files are stored, "NO FILES" appears.

• When the player is turned off in stop mode or during playback and

then turned on again, it will resume playback from the beginning of the track lastly played when you start playback.

• The menu mode returns to the previous display before this menu is

displayed if no operation is made for approx. 10 seconds.

BASIC OPERATIONS

NAVIGATE

Use to display the hierarchical tree structure of music folders and files ( ). From this tree structure, you can easily locate a desired music file and play it back.

To locate a music file

1. After turning on the player, press MENU button and ¢ / 4 button

to select NAVIGATE mode from Main Menu, and then press 3 8

button to enter that mode.

2. Press ¢ / 4, 3 8 / 7 buttons to locate the desired file.

¢ / 4 : Moves the cursor (highlight) vertically. The cursor scrolls

through the files and folders in the selected folder.

3 8 / 7 : 1) Move the cursor to the desired folder and press 3 8

button to open it. Then, the files in the folder can be selected.

2) When the cursor is inside the folder, press 7 button to

close the folder. Then, the hierarchical structure appears including that folder.

3. Press 3 8 button to play it back.

(Press 3 8 button to pause and 7 button to stop.)

To exit NAVIGATE mode: Press MENU button.

BASIC OPERATIONS

Music file playing order in Music mode:

From the hierarchical tree structure, you can easily understand the playing order of music files when you normally play them in Music mode. You will see that the music files are played back in the order from the higher hierarchy to the lower one.

NOTES

• Maximum number of folders that can be recognized by the player is 50.

• Maximum number of hierarchies that can be recognized by the player

is 8, including the highest-order folders.

• You can change the playback order of music files by adding numbers

at the head of folder names or file names on PC. (For example, add numbers like 01xxxx, 02yyyy, ...)

• The maximum number of files (WMA, MP3 and WAV files) that can be

displayed or operated is 550. On a file exceeding 550, its operation is not guaranteed.

BASIC OPERATIONS

RECORDING MUSIC FROM EXTERNAL AUDIO EQUIPMENT IN LINE-IN MODE

You can record the music played back on external audio equipment. Make sure that the audio cable is connected between the LINE IN terminal of this audio player and the external audio equipment.

To record music from external audio equipment

1. After turning on the player, press MENU button and ¢ / 4 button

to select LINE IN mode from Main menu, and then press 3 8 button

to enter that mode.

2. Press and hold REC button until "Recording" appears.

The player is paused (the counter is stopped).

3. Play the music source on the external audio equipment.

The player automatically detects the sound, starts recording of the music and numbers each track. The default recording setting is as follows. Bit rate: 128kbps, A.TRK: ON. For details, see pages 32 to 33.

To stop: Press 7 button.

To exit LINE IN mode: Press MENU button.

BASIC OPERATIONS

NOTES

• The "LINE" folder is automatically generated, the recorded music files

are stored in it as MP3 files. The "LINE" folder can be displayed using NAVIGATE mode. (See page 19.)

• If "Low Battery" appears when you press and hold REC button, you

need to charge the battery.

• The player consumes an enormous amount of power for recording the

music stored in the external audio equipment. To prevent malfunction due to low battery, the player is designed to stop faster in this mode. It is recommended to use a fully charged battery if you continue to record the music for many hours in this mode.

• AUTO LEVEL CONTROL (ALC)

• The player is equipped with Auto Level Control (ALC) to control distortion during recording. When the output level from external audio equipment is too high, the ALC automatically activates to control the recording level, which can reduce distortion.

• When you perform test recording beforehand or check and control the output level by inserting the headphones to the jack of the player during recording, more proper level setting can be obtained.

• The recorded files can be copied to the computer connected to the player by USB.

BASIC OPERATIONS

DELETING FILES

(DELETE submenu) (File deletion)

To delete files

1. After turning on the player, press MENU button and ¢ / 4 button

to select DELETE mode from Main Menu, and then press 3 8 button

to enter that mode.

2. Press ¢ / 4 button to select "MUSIC FILES".

3. Press 3 8 button.

4. Press ¢ / 4 button to select a file you want to delete.

5. Press 7 button to select "YES".

To cancel the operation, select "NO".

6. Press 3 8 button to delete the file.

"File Deleted" appears. If you try to delete a read-only file, "Operation Failed" appears.

(Each time you press 7 button, the status switches between "YES"

and "NO".)

To return to DELETE menu: Press MENU button once.

To exit DELETE mode:

Press MENU button again (or select "EXIT" and press 3 8 button in

DELETE submenu).

NOTE

• When all files in a folder are deleted, the folder disappears from the player. However, it is not erased and remains in the player. You can erase this folder by PC through USB.

ADVANCED FEATURES

SET MENU ITEMS

In SET mode, you can set the following SET MENU items: EQ SET (Equalization Set), PLAYMODE, SLEEP TIMER, A.POWER OFF (Auto Power OFF), BACKLIGHT, CONTRAST, RECORD SET and LANGUAGE. To set each item, see the relevant later page.

EQUALIZER

You can select from one of 6 different preset sound modes or one customized sound mode.

High

Level

Low

Frequency

Types of sound modes

NORMAL

No sound effect applies.

CLASSICAL

Good for classical music

JAZZ

Good for jazz music

ROCK

Boosts low and high frequency.

POP

Good for vocal music

BASS

Empowers bass sound.

HighLow

CUSTOMIZED

You can create your own sound mode.

ADVANCED FEATURES

To select sound mode

1. After turning on the player, press MENU button and ¢ / 4 button

to select SET mode from Main Menu, and then press 3 8 button to

enter that mode.

2. Press ¢ / 4 button to select "EQ SET".

3. Press 3 8 button.

4. Press ¢ / 4 button to select the sound mode.

5. Press 3 8 button to return to SET MENU.

To create sound mode (CUST)

1. After turning on the player, press MENU button and ¢ / 4 button

to select SET mode from Main Menu, and then press 3 8 button to

enter that mode.

2. Press ¢ / 4 button to select "EQ SET".

3. Press 3 8 button.

4. Press ¢ / 4 button to select "CUST".

5. Press MENU button briefly to start editing.

The indicator of the lowest frequency is highlighted.

6. Press ¢ / 4 button to select the frequency you want to edit.

7. Press 3 8 button.

The indicator starts to blink.

8. Press ¢ / 4 button to set the level up or down and then press

38 button to store it.

9. Repeat Steps 6 through 8 to edit for other frequencies.

10.

Press completed.

button briefly. The highlight disappears and the setting is

11. Press 3 8 button to return to SET MENU.

To exit SET mode:

Press MENU.

button (or select "EXIT" and press

3 8

button) in the SET

ADVANCED FEATURES

PLAYMODE

You can select various play modes.

Types of playback modes

Mode Display Explanation

NORMAL Normal play

REPEAT ONE Repeats one track.

REPEAT ALL Repeats all tracks.

RPT FOLDER Repeats all tracks of a folder which

has a track being played back, or repeats all tracks of a folder which has a track selected in NAVIGATE mode.

RANDOM Plays all tracks in random order.

RANDOM RPT

RND FOLDER Repeats all tracks of a folder which

INTRO Plays first 10 seconds for each tracks.

Repeats all tracks in random order.

has a track being played back, or plays all tracks of a folder which has a track selected in NAVIGATE mode, in random order.

When all tracks are played, the display disappears and the mode is canceled.

ADVANCED FEATURES

To select play mode

1. After turning on the player, press MENU button and ¢ / 4 button

to select SET mode from Main Menu, and then press 3 8 button to

enter that mode.

2. Press ¢ / 4 button to select "PLAYMODE".

3. Press 3 8 button.

4. Press ¢ / 4 button to select the play mode.

5. Press 3 8 button to return to SET MENU.

To exit SET mode:

Press MENU button (or select "EXIT" and press 3 8 button) in the

SET MENU.

ADVANCED FEATURES

SLEEP TIMER

Use the sleep timer to turn off the player after a certain period of time during playback. You can set the period of time to 15, 30, 45, 60 minutes, or OFF (default). The sleep timer works temporarily. Once it has worked,

it is canceled. When the sleep timer is set, the sleep timer icon ( ) appears on the upper right of the display.

To set sleep timer

1. After turning on the player, press MENU button and ¢ / 4 button

to select SET mode from Main Menu, and then press 3 8 button to

enter that mode.

2. Press ¢ / 4 button to select "SLEEP TIMER".

3. Press 3 8 button.

4. Press ¢ / 4 button to select the time.

5. Press 3 8 button to return to SET MENU.

To exit SET mode:

Press MENU button (or select "EXIT" and press 3 8 button) in the

SET MENU.

+ 64 hidden pages