JVC KD-S5050, KD-S10UJ, KD-S5050UC, KD-S5050UJ, KD-S50J Instructions Manual

...

ENGLISH

CD RECEIVER

RECEPTOR CON CD RECEPTEUR CD

KD-S5050

DISP

SEL

DIRECT

TRACK ACCESS

ESPAÑOL

FRANÇAIS

For installation and connections, refer to the separate manual. Para la instalación y las conexiones, refiérase al manual separado. Pour l’installation et les raccordements, se référer au manuel séparé.

INSTRUCTIONS

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

For customer Use:

Enter below the Model No. and Serial No. which are located on the top or bottom of the cabinet. Retain this information for future reference.

Model No.

Serial No.

GET0171-001A

[J]

INFORMATION (For U.S.A.)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

ENGLISH

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

– Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside unit; leave all

servicing to qualified service personnel.

3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated. Avoid

direct exposure to beam.

How to reset your unit

While holding SEL (Select), press (Standby/On Attenuator) for more than 2 seconds. This will reset the built-in microcomputer.

(Standby/On Attenuator)

SSM

RPT RND

MODE

SEL (Select)

NOTES:

• Your preset adjustments — such as preset channels or sound adjustments — will also be erased.

• If a CD is in the unit, it will eject when you reset the unit. Be careful not to drop the CD.

SCM

Thank you for purchasing a JVC product. Please read all instructions carefully before operation,

to ensure your complete understanding and to obtain the best possible performance from the unit.

CONTENTS

How to reset your unit .................................. 2

How to use the MODE button ...................... 3

LOCATION OF THE BUTTONS ...............4

Control panel ............................................... 4

BASIC OPERATIONS ..........................5

Turning on the power ................................... 5

RADIO OPERATIONS .........................6

Listening to the radio ................................... 6

Storing stations in memory .......................... 7

Tuning in to a preset station ........................ 8

CD OPERATIONS ..............................9

Playing a CD ................................................ 9

Locating a track or a particular portion

on a CD .................................................. 10

Selecting CD playback modes ................... 10

Prohibiting CD ejection .............................. 11

ENGLISH

SOUND ADJUSTMENTS .................... 12

Adjusting the sound ................................... 12

Turning on/off the loudness function ............. 12

Using the Sound Control Memory (SCM) .. 13

Storing your own sound adjustments ........ 14

OTHER MAIN FUNCTIONS ................. 15

Setting the clock ........................................ 15

Canceling Advanced SCM – SCM LINK .... 15

Selecting the level display ......................... 16

Detaching the control panel ....................... 17

MAINTENANCE .............................. 18

Handling discs ........................................... 18

TROUBLESHOOTING ....................... 19

SPECIFICATIONS ............................ 20

How to use the MODE button

If you press MODE, the unit goes into functions mode and the number buttons work as different function buttons.

MODE

To use these buttons as number buttons again after pressing MODE, wait for 5 seconds without pressing any number button until the functions mode is cleared.

• Pressing MODE again also clears the functions mode.

RPT RND

Time countdown indicator

BEFORE USE

For safety....

• Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.

• Stop the car before performing any complicated operations.

* Temperature inside the car....

If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes normal before operating the unit.

LOCATION OF THE BUTTONS

Control panel

ENGLISH

Display window

;

DIRECT TRACK ACCESS

f g

RPT RND

MODE

SCM

SSM

1 (Standby/On Attenuator) button 2 +/– button

3 LOUD (Loudness) button 4 SEL (Select) button 5 Loading slot 6 AM button 7 0 (Eject) button 8 CD button 9 FM button p DISP (Display) button q MO (Monaural) button w RPT (Repeat) button e RND (Random) button r Number buttons t MODE button y SCM (Sound Control Memory) button u

(Control panel release) button

i 4

• Also functions as SSM buttons when

/ ¢ buttons

pressed together.

q e r

Display window

o SCM (Sound Control Memory) indicator ; CD indicator a Band indicators

FM1, FM2, FM3 AM

s Tuner reception indicators

MO (Monaural), ST (Stereo)

d RND (Random) indicator f RPT (Repeat) indicator g LOUD indicator h CD-in indicator j Main display k Volume level indicator

BASIC OPERATIONS

Turning on the power

Turn on the power.

Note on One-Touch Operation:

When you select a source in step 2 below, the power automatically comes on. You do not have to press this button to turn on the power.

Select the source.

SSM

RPT RND

Adjust the sound as you want (see

MODE

SCM

ENGLISH

pages 12 – 14).

To drop the volume in a moment

Press briefly while listening to any source. “ATT” starts flashing on the display, and the volume level will drop in a moment. To resume the previous volume level, press the button briefly again.

To turn off the power

Press and hold until "SEE YOU" appears on the display.

To operate the tuner (FM or AM),

see pages 6 – 8.

To operate the CD,

see pages 9 – 11.

Adjust the volume.

To increase the volume.

To decrease the volume.

Volume level indicator (see page 16)

Note:

When you use this unit for the first time, set the builtin clock correctly, see page 15.

CAUTION on volume setting

CDs produce very little noise compared with other sources. If the volume level is adjusted for the tuner, for example, the speakers may be damaged by the sudden increase in the output level. Ther efore, lower the volume before playing a disc and adjust it as required during playback.

Volume level appears

ENGLISH

RADIO OPERATIONS

RPT RND

MODE

SCM

SSM

Listening to the radio

You can use either automatic searching or manual searching to tune in to a particular station.

Searching a station automatically: Auto search

Select the band (FM 1 – 3, AM).

Selected band appears

Note:

This receiver has three FM bands (FM1, FM2, FM3). You can use any one of them to listen to an FM broadcast.

FM1 FM2

FM3

Lights up when receiving an FM stereo broadcast with sufficient signal strength

To stop searching before a station is received,

press the same button you have pressed for searching.

Searching a station manually: Manual search

Select the band (FM 1 – 3, AM).

Note:

This receiver has three FM bands (FM1, FM2, FM3). You can use any one of them to listen to an FM broadcast.

Press and hold ¢ or 4 until “M” (manual) starts flashing on the display.

FM1 FM2

FM3

Start searching a station.

Press ¢ to search stations of higher frequencies.

Press 4 to search stations of lower frequencies.

When a station is received, searching stops.

Selected band appears

Tune in to a station you want while “M” (manual) is flashing.

Press stations of higher frequencies.

¢ to search

Storing stations in memory

You can use one of the following two methods to store broadcasting stations in memory.

• Automatic preset of FM stations: SSM (Strongstation Sequential Memory)

• Manual preset of both FM and AM stations

ENGLISH

Press 4 stations of lower frequencies.

• If you release your finger from the button, the manual mode will automatically turn off after 5 seconds.

• If you hold down the button, the frequency keeps changing (in 200 kHz intervals for FM and 10 kHz for AM) until you release the button.

to search

When an FM stereo broadcast is hard to receive:

1 Press MODE to enter the functions mode while

listening to an FM stereo broadcast.

2 Press MO (monaural), while still in the functions

mode, so that the MO indicator lights up on the display. Each time you press the button, the MO indicator lights up and goes off alternately.

MODE

FM station automatic preset: SSM

You can preset 6 local FM stations in each FM band (FM1, FM2 and FM3).

Select the band (FM1 – 3) you want to store FM stations into.

Press and hold both buttons for more than 2 seconds.

SSM

FM1 FM2

FM3

MO (monaural) indicator

When the MO indicator is lit on the display, the sound you hear becomes monaural but the reception will be improved.

“SSM” appears, then disappears when automatic preset is over.

Local FM stations with the strongest signals are searched and stored automatically in the band number you have selected (FM1, FM2 or FM3.) These stations are preset in the number buttons – No.1 (lowest frequency) to No.6 (highest frequency). When automatic preset is over, the station stored in number button 1 will be automatically tuned in.

Manual preset

You can preset up to 6 stations in each band (FM1, FM2, FM3 and AM) manually.

Ex: Storing an FM station of 92.5 MHz into the

ENGLISH

preset number 1 of the FM1 band.

Select the band (FM1 – 3, AM) you want to store FM stations into (in this example, FM1).

• Each time you press the button, the FM band changes as follows:

FM1 FM2

FM3

Notes:

• A previously pr eset station is erased when a new station is stored in the same preset number.

• Preset stations are erased when the power supply to the memory circuit is interrupted (for example, during battery replacement). If this occurs, preset the stations again.

Tuning in to a preset station

You can easily tune in to a preset station. Remember that you must store stations first. If you have not stored them yet, see “Storing stations in memory” on page 7 and 8.

Select the band (FM1 – 3, AM).

Tune in to a station of 92.5 MHz.

Press and hold the number button

Press ¢ to tune stations of higher frequencies.

Press 4 stations of lower frequencies.

(in this example, 1) for more than 2 seconds.

to tune

FM1 FM2

FM3

Select the number (1 – 6) for the preset station you want.

RPT RND

“P1” flashes for a few seconds.

Repeat the above procedure to store other stations into other preset numbers.

CD OPERATIONS

SSM

RPT RND

MODE

SCM

ENGLISH

Playing a CD

Insert a disc into the loading slot.

The unit turns on, draws a CD and starts playback automatically.

Note on One-Touch Operation:

When a CD is already in the loading slot, pressing CD turns on the unit and starts playback automatically.

The CD-in indicator flashes

Note:

When a CD is inserted upside down, the CD automatically ejects.

To stop play and eject the CD

Press 0. CD play stops and the CD automatically ejects from the loading slot.

• If you change the source, the CD play also stops (without ejecting the CD). Next time you select “CD” as the source, CD play starts from where playback has been stopped previously.

Notes:

• If the ejected disc is not removed for about 15 seconds, the disc is automatically inserted again into the loading slot to protect it from dust. (CD play will not start this time.)

• You can eject the CD even when the unit is turned off.

The CD-in indicator lights up

Total playing time of the inserted disc

Elapsed playing time

All tracks will be played repeatedly until you stop playback.

Total track number of the inserted disc

Current track

About mistracking:

Mistracking may result from driving on extremely rough roads. This does not damage the unit and the CD, but will be annoying. We recommend that you stop CD play while driving on such rough roads.

Locating a track or a particular

RND

MODE

RPT

MODE

portion on a CD

Selecting CD playback modes

To play back tracks at random (Random Play)

To fast-forward or reverse the track

ENGLISH

Press and hold while playing a CD, to fast forward the track.

Press and hold 4 while playing a CD, to reverse the track.

To go to the next tracks or the previous tracks

Press ¢ briefly, while playing a CD, to go ahead to the beginning of the next track. Each time you press the button consecutively, the beginning of the next tracks is located and played back.

Press 4 playing a CD, to go back to the beginning of the current track. Each time you press the button consecutively, the beginning of the previous tracks is located and played back.

briefly, while

To go to a particular track directly

¢,

RPT RND

You can play back all tracks on the CD at random.

1 Press MODE to enter the functions mode

while playing a CD.

2 Press RND (Random), while still in the functions

mode, so that the RND indicator lights up on the display. Each time you press the button, CD random play mode turns on and off alternately.

RND indicator

When the random play is turned on, the RND indicator lights up on the display. A track randomly selected starts playing.

To play back tracks repeatedly (Repeat Play)

You can play back the current track repeatedly.

1 Press MODE to enter the functions mode

while playing a CD.

2 Press RPT (Repeat), while still in the functions

mode, so that the RPT indicator lights up on the display. Each time you press the button, CD repeat play mode turns on and off alternately.

Press the number button corresponding to the track number to start its playback.

• To select a track number from 1 – 6: Press 1 (7) – 6 (12) briefly.

• To select a track number from 7 – 12: Press and hold 1 (7) – 6 (12) for more than 1 second.

Track number of the currently

RPT indicator

When the repeat play is turned on, the RPT indicator lights up on the display. The current track starts playing repeatedly.

playing track

Prohibiting CD ejection

You can prohibit the CD ejection and can lock a CD in the loading slot.

While pressing CD, press and hold 0 for more than 2 seconds.

“EJECT” flashes on the display for about 5 seconds, and the CD is locked and cannot be ejected.

To cancel the prohibition and unlock the CD

While pressing CD, press and hold 0 again for more than 2 seconds. “EJECT” appears on the display, and the CD ejects from the loading slot.

ENGLISH

The CD-in indicator flashes

+ 25 hidden pages

JVC KD-S5050, KD-S10UJ, KD-S5050UC, KD-S5050UJ, KD-S50J Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual