JVC KD-R988BTS, KD-R888BT Instruction Manual

KD-R988BTS / KD-R888BT

CD RECEIVER

INSTRUCTION MANUAL

RÉCEPTEUR CD

MANUEL D’INSTRUCTIONS

RECEPTOR CON CD

MANUAL DE INSTRUCCIONES

ENGLISH

FRANÇAIS

ESPAÑOL

For customer Use:

Enter below the Model No. and Serial No. which are located on the top or bottom of the cabinet. Retain this information for future reference. Model No. Serial No.

B5A-1351-00 [K]

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety.

JVC KENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN

THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.

Location : Top Plate

Información acerca de la eliminación de equipos eléctricos y electrónicos al final de la vida útil (aplicable a los países que hayan adoptado sistemas independientes de recogida de residuos)

Los productos con el símbolo de un contenedor con ruedas tachado no podrán ser desechados como residuos domésticos. Los equipos eléctricos y electrónicos al final de la vida útil, deberán ser reciclados en instalaciones que puedan dar el tratamiento adecuado a estos productos y a sus subproductos residuales correspondientes. Póngase en contacto con su administración local para obtener información sobre el punto de recogida más cercano. Un tratamiento correcto del reciclaje y la eliminación de residuos ayuda a conservar los recursos y evita al mismo tiempo efectos perjudiciales en la salud y el medio ambiente.

FCC WARNING

This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

FCC NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Informação sobre a eliminação de pilhas

Este produto não deve ser eliminado como lixo doméstico geral. Devolva a pilha usada ao revendedor ou entidade autorizada para que a mesma seja devolvida ao fabricante ou importador. A reciclagem e a eliminação de lixo de maneira apropriada ajudarão a conservar os recursos naturais ao mesmo tempo que prevenirão os efeitos prejudicais à nossa saúde e ao meio ambiente.

CALIFORNIA, USA ONLY

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material—special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

IC (Industry Canada) Notice

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) this device must accept any interference, including interference that may cause

undesired operation of the device.

Note de IC (Industrie Canada)

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux apprareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage; (2) I’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d’en compromettre le fonctionnement.

Contains Bluetooth Module FCC ID: ZWY8811X IC ID: 12033A-8811X

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

CAUTION

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that is deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20 cm or more away from person’s body.

ATTENTION

Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices d’exposition et d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est considérée comme conforme sans évaluation de l’exposition maximale autorisée (MPE). Cependant, il est souhaitable qu’il devrait être installé et utilisé en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain.

Para cumplimiento de la IFT:

“La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda

causar su operación no deseada”

SOFTWARE LICENSE AGREEMENT

The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions which Users shall follow in order to use the Licensed Software.

The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement. This Agreement shall be deemed completed at the time the User (hereinafter the "User") initially used the Product in which the "Licensed Software" is embedded.

The Licensed Software may include the software which has been licensed to the Licensor directly or indirectly from any third party. In such case, some third parties require the Users to follow their conditions for use separately from this Software License Agreement. Such software shall not be subject to this Agreement, and the Users are urged to read the "Important Notice concerning the Software" to be provided separately below.

Article 1 General Provision

The Licensor shall grant to the User a non-exclusive and non-transferable (other than the exceptional case referred to in Article 3, Paragraph 1) licensed to use the Licensed Software within the country of the User. (the country where the User bought the Product(hereinafter the "Country")

Article 2 License

1. The license granted under this Agreement shall be the right to use the Licensed Software in the Product.

2. The User shall not duplicate, copy, modify, add, translate or otherwise alter, or lease the Licensed Software and any related documents, whether in whole or in part.

3. The use of the Licensed Software shall be limited to personal purpose, and the Licensed Software shall not be distributed, licensed or sub-licensed whether it is for commercial purpose or not.

4. The User shall use the Licensed Software according to the directions described in the operation manual or help file, and is prohibited to use or duplicate any data in a manner violating the Copyright Law or any other laws and regulations by applying whole or a part of the Licensed Software.

Article 3 Conditions for Grant of License

1. When the User transfers the Product, it may also transfer the license to use the Licensed Software embedded in the Product (including any related materials, updates and upgrades) on condition that no original, copies or related materials continue in the possession of the User, and that the User shall cause the transferee to comply with this Software License Agreement.

2. The User shall not carry out reverse engineering, disassembling, decompiling or any other code analysis works in connection with the Licensed Software.

Article 4 Right pertaining to the Licensed Software

Any and all copyrights and other rights pertaining to the Licensed Software and related documents shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any related documents.

Article 5 Indemnification of Licensor

1. Neither the Licensor nor the Original Rightholder shall be liable for any damage incurred by the User or any third party due to the exercise of the license granted to the User under this Agreement, unless otherwise restricted by law.

2. The Licensor will offer no guarantee for the merchantability, convertibility and consistency with certain objective of the Licensed Software.

Article 6 Liability to Third Party

If any dispute has arisen with any third party due to an infringement upon a copyright, patent or any other intellectual property right that was caused by the User's use of the Licensed Software, the User shall settle such dispute at its own cost and hold the Licensor and the Original Rightholder harmless from any inconvenience it may cause.

Article 7 Confidentiality

The User shall keep the confidentiality of such portion of the Licensed Software, related documents thereof or any other information to be granted under this Agreement, as well as the conditions of this Agreement as has not yet entered the public domain, and shall not disclose or divulge the same to any third party without approval of the Licensor.

iii

Article 8 Termination

In case the User falls under any of the events described in the following items, the Licensor may immediately terminate this Agreement or claim that the User compensates for the damage incurred by the Licensor due to such event: (1) when the User violated any provision of this Agreement; or (2) when a petition has been filed against the User for an attachment, provisional attachment, provisional disposition or any other compulsory execution.

Article 9 Destruction of the Licensed Software

If this Agreement is terminated pursuant to the provision of Article 8, the User shall destroy the Licensed Software, any related documents and copies thereof within two (2) weeks from such date of termination.

Article 10 Protection of Copyright

1. The copyright and all the other intellectual property rights relating to the Licensed Software shall belong to the Licensor and the Original Rightholder, and in no event shall they be under the ownership of the User.

2. The User shall, whenever it uses the Licensed Software, comply with any laws relating to the copyright and other intellectual property rights.

Article 11 Export Restriction

1. It is prohibited to export the Licensed Software and any related documents outside the country of the User (including transmission thereof outside the country of the User via Internet of other communication tools).

2. The User shall understand that the Licensed Software shall be subject to the export restrictions adopted by the country of User and any other countries.

3. The User shall agree that the software will be subject to any and all applicable international and domestic laws (including the export control regulation of the country of User and any other countries, and any restrictions concerning the end-users, the use by end-users and importing countries to be provided by the country of User and any other countries, and any other governmental authorities).

Article 12 Miscellaneous

1. In the event any part of this Agreement is invalidated by operation of law, the residual provisions shall continue in force.

2. Matters not stipulated in this Agreement or any ambiguity or question raised in the construction of this Agreement shall be provided or settled upon good-faith consultation between the Licensor and the User.

3. The Licensor and the User hereby agree that this Agreement is governed by the laws of Japan, and any dispute arising from, and relating to the rights and obligations under, this Agreement shall be submitted to the exclusive jurisdiction of the Tokyo District Court for its first instance.

Important Notice concerning the Software

-jansson

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

CONTENTS BEFORE USE

BEFORE USE 2

BASICS 3

GETTING STARTED 4

1 Cancel the demonstration 2 Set the clock and date 3 Set the basic settings

RADIO 5

CD/USB/iPod/ANDROID 7

Pandora® 9

iHeartRadio® 10

SiriusXM® Radio 11

(for KD-R988BTS)

BLUETOOTH® 14

AUX 21

AUDIO SETTINGS 22

DISPLAY SETTINGS 27

REFERENCES 28

Maintenance More information

TROUBLESHOOTING 31

INSTALLATION/ CONNECTION 33

SPECIFICATIONS 36

IMPORTANT

•

To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe Warning and Caution in this manual.

•

Please keep the manual in a safe and accessible place for future reference.

WARNING

•

Do not operate any function that takes your attention away from safe driving.

•

Do not ingest the battery, Chemical Burn Hazard

The remote control supplied with this product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Caution

Volume setting:

•

Adjust the volume so that you can hear sounds outside the car to prevent accidents.

•

Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.

General:

•

Avoid using the external device if it might hinder safe driving.

•

Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.

•

Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short circuit.

•

If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.

Remote control (RM-RK52):

•

Do not leave the remote control in hot places such as on the dashboard.

•

The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.

•

The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

How to read this manual

•

Operations are explained mainly using buttons on the faceplate of

•

English indications are used for the purpose of explanation. You can select the display language from the menu.

•

[XX]

indicates the selected items.

•

( XX)

indicates references are available on the stated page.

KD-R988BTS

( 5)

ENGLISH

BASICS

Faceplate

Loading slot

Detach button

Attach How to resetDetach

To On the faceplate On the remote control

Turn on the power

Adjust the volume Press

Select a source • Press

Change the display information

Press

• Press and hold to turn off the power.

• Press and hold volume to 15

Press

• Press again to cancel.

• Press

Press

Display window

KD-R988BTS:

USB cable from the rear of the unit

to continuously increase the

to mute the sound or pause playback.

repeatedly. , then press within 2 seconds.

repeatedly.

( 30)

Remote control (RM-RK52)

This unit can be remotely controlled with an optionally purchased remote control.

Remote sensor (Do not expose to bright sunlight.)

Pull out the insulation sheet when using for the first time.

How to replace the battery

( Not available )

Press

• Press and hold the volume to 15.

Press

• Press again to cancel.

Press SOURCE repeatedly.

( Not available )

or .

to mute the sound or pause playback.

to continuously increase

ENGLISH

GETTING STARTED

Cancel the demonstration

When you turn on the power for the first time (or

[YES]

), the display shows: “CANCEL DEMO” “PRESS ENTER”

1 Press .

[YES]

is selected for the initial setup.

2 Press again.

“DEMO OFF” appears.

Set the clock and date

Press and hold .

2 Press to select

To adjust the clock

3 Press to select

[CLOCK]

, then press .

[CLOCK ADJUST]

4 Press to make the settings, then press .

Hour

5 Press to select 6 Press to select

To set the date

7 Press to select

Minute

[CLOCK FORMAT] [12H]

[24H]

[DATE SET]

, then press .

8 Press to make the settings, then press .

Day

Month Year

9 Press to exit.

To return to the previous setting item, press .

[FACTORY RESET]

, then press .

is set to

Set the basic settings

Press and hold .

2 Press to select an item (see the following table), then

press

3 Repeat step 2 until the desired item is selected or activated. 4 Press to exit.

To return to the previous setting item, press .

Default:

SYSTEM

KEY BEEP

SOURCE SELECT

AM SRC

PANDORA SRC

IHEART SRC

BUILT-IN AUX

F/W UPDATE

UPDATE SYSTEM

F/W UP xxxx

FACTORY RESET YES

Not displayed when the corresponding source is selected.

(Not applicable when 3-way crossover is selected.)

:Activates the keypress tone.;

:Enables AM in source selection.;

:Enables PANDORA FRONT/PANDORA REAR/PANDORA in source

selection.;

OFF

:Disables.

:Enables IHEART FRONT/IHEART REAR/IHEARTRADIO in source

selection.;

OFF

:Disables.

:Enables AUX in source selection.;

YES

:Starts upgrading the firmware.; NO:Cancels (upgrading is not activated). For details on how to update the firmware, see: <http://www.jvc.net/cs/car/>.

:Resets the settings to default (except the stored station).;

:Cancels.

( 9)

( 10)

OFF

:Deactivates.

OFF

:Disables.

( 5)

( 21)

ENGLISH

GETTING STARTED

CLOCK

TIME SYNC

CLOCK DISPLAY ON

ENGLISH

ESPANOL

:The clock time is automatically set using the Clock Time (CT) data in FM Radio Broadcast Data System signal.;

:The clock time is shown on the display even when the unit is turned off.;

Select the display language for menu and music information if applicable. By default,

ENGLISH

OFF

:Cancels.

is selected.

OFF

:Cancels.

RADIO

“ST” lights up when receiving an FM stereo broadcast with sufficient signal strength.

Search for a station

Press repeatedly to select FM or AM.

2 Press (or press on the remote control) to search for a station

automatically.

(or) Press and hold (or press and hold on the remote control) until “M”

flashes, then press repeatedly to search for a station manually.

Settings in memory

You can store up to 18 stations for FM and 6 stations for AM.

Store a station

While listening to a station....

Press and hold one of the number buttons (1 to 6).

(or) 1 Press and hold until “PRESETMODE” flashes. 2 Press to select a preset number, then press .

The preset number flashes and “MEMORY” appears.

Select a stored station

Press one of the number buttons (1to6).

(or) 1 Press . 2 Press to select a preset number, then press .

ENGLISH

RADIO

Other settings

Press and hold .

2 Press to select an item

press

(

see the following table), then

3 Repeat step 2 until the desired item is selected/activated or follow

the instructions stated on the selected item.

4 Press to exit.

To return to the previous setting item, press .

Default:

TUNER SETTING

RADIO TIMER

Turns on the radio at a specific time regardless of the current source.

1 ONCE/DAILY/WEEKLY/OFF

on.

2 FM/AM/SIRIUS XM 3 01

to 18 (for FM/SIRIUS XM)/01 to 06 (for AM):Select a preset station.

Set the activation day

“

” lights up when complete.

:Select how often the timer will be turned

:Select the source.

and time.

Radio Timer will not activate for the following cases.

•

The unit is turned off.

•

[OFF]

SSM

is selected for

for AM is selected.

SSM 01–06/SSM 07–12/SSM 13–18

[AM SRC]

( 4)

[SOURCE SELECT]

: Automatically presets up to 18

after Radio Timer

stations for FM. “SSM” stops flashing when the first 6 stations are stored. Select

SSM 07–12/SSM 13–18

to store the following 12 stations.

IF BAND AUTO

MONO SET

AREA US

PTY SEARCH

For

Selectable only when

Only for FM source.

PTY code

NEWS, INFORM ADLT HIT NOSTALGA SOFT R&B REL TALK

(Spanish talk),

:Increases the tuner selectivity to reduce interference noises from adjacent FM stations. (Stereo effect may be lost.); interference noises from adjacent FM stations, but sound quality will not be degraded and the stereo effect will remain.

:Improves the FM reception, but the stereo effect will be lost.;

OFF

:Cancels.

: For North/Central/South America, AM/FM intervals: 10kHz/200kHz.;

:For some South American countries, AM/FM intervals: 10kHz/50kHz.;

:For any other areas, AM/FM intervals: 9kHz/50kHz.

Select a PTY code (see below). If there is a station broadcasting a program of the same PTY code as you have selected, that station is tuned in.

KD-R988BTS:

Selectable only when SiriusXM Vehicle Tuner is connected.

[ONCE]

(information),

(adult hits),

(nostalgia),

SOFT RCK

JAZZ, CLASSICL

(soft rhythm and blues),

(religious talk),

MUSC ESP

(Spanish music),

[WEEKLY]

is selected in step 1.

SPORTS, TALK, ROCK, CLS ROCK

(softrock),

TOP 40, COUNTRY, OLDIES, SOFT

(classical),

LANGUAGE, REL MUSC

PERSNLTY

(personality),

HIP HOP, WEATHER

WIDE

:Subjects to

( 11)

(classic rock),

R & B

(rhythm and blues),

(religious music),

PUBLIC, COLLEGE, HABL ESP

ENGLISH

CD/USB/iPod/ANDROID

Start playback

The source changes automatically and playback starts.

Eject disc

Label side

Selectable sources:

•

KD-R988BTS

•

KD-R888BT

: CD/USBFRONT/USBREAR/iPodFRONT/iPodREAR/ANDROIDFRONT/ANDROIDREAR

: CD/USB/iPodUSB/ANDROID

USB input terminal

KD-R988BTS

: You can also connect to the USB cable from the rear of the unit.

USB

USB 2.0 cable

(commercially available)

iPod/iPhone

Accessory of the iPod/iPhone

ANDROID

Micro USB 2.0 cable

(commercially available)

To On the faceplate On the remote control

Reverse/Fast-forward

Select a track/file Press

Select a folder

Repeat play

Random play

Do not leave the cable inside the car when not using.

When connecting an Android device, “Press [VIEW] to install JVC MUSIC PLAY APP” is shown. Follow the instructions to install

Press and hold .

Press . Press .

Press repeatedly.

TRACK REPEAT/ALL REPEAT

: Audio CD

TRACK REPEAT/FOLDER REPEAT/ALL REPEAT ONE REPEAT/ALL REPEAT/REPEAT OFF

Press repeatedly.

ALL RANDOM/RANDOM OFF

: Audio CD

FOLDER RANDOM/ALL RANDOM/RANDOM OFF SONG RANDOM/ALL RANDOM/RANDOM OFF

Press and hold

Press

: MP3/WMA/AAC/WAV/FLAC file

: iPod or ANDROID

: MP3/WMA/AAC/WAV/FLAC file

: iPod or ANDROID

the application. You can also install the latest version of JVC MUSIC PLAY application on your Android device before connecting. For more information, visit <http://www.jvc.net/cs/car/>.

For ANDROID: Applicable only when

For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ANDROID.

For iPod/ANDROID: Applicable only when

[AUTO MODE]

is selected.

[HEAD MODE]/[AUTO MODE]

( 8)

is selected.

( 8)

ENGLISH

CD/USB/iPod/ANDROID

Select control mode

While in iPodFRONT/iPodREAR/iPodUSB source, press repeatedly.

HEAD MODE IPHONE MODE

While in ANDROIDFRONT/ANDROIDREAR/ANDROID source, press

AUTO MODE

AUDIO MODE

: Control iPod from this unit.

: Control iPod using the iPod itself. However, you can still

play/pause or file skip from this unit.

repeatedly.

: Control Android device from this unit via JVC MUSIC PLAY

application installed in the Android device.

: Control Android device using the Android device itself via

other media player applications installed in the Android device. However, you can still play/pause or file skip from this unit.

Select music drive

While in USBFRONT/USBREAR/USB source, press repeatedly.

Stored songs in the following drive will be played back.

• Selected internal or external memory of a smartphone (Mass Storage

Class).

• Selected drive of a multiple drives device.

Settings to use JVC Remote application

JVC Remote application is designed to control the JVC car receiver’s operations from the iPhone/iPod (via USB input terminal).

Preparation:

Install the latest version of JVC Remote application on your device before connecting. For more information, visit <http://www.jvc.net/cs/car/>.

You can make the settings in the same way as connection via Bluetooth.

( 14)

ENGLISH

Select a file from a folder/list

For iPod/ANDROID, applicable only when selected.

[HEAD MODE]/[AUTO MODE]

1 Press . 2 Press to select a folder/list, then press . 3 Press to select a file, then press .

Quick search

FRONT, ANDROID REAR and ANDROID source)

If you have many files, you can search through them quickly.

Press and hold to browse through the list quickly.

Alphabet search

ANDROID FRONT, ANDROID REAR and ANDROID source)

You can search for a file according to the first character.

For iPodFRONT/iPodREAR/iPodUSB source Press OTHERS).

• Select “OTHERS” if the first character is other than AtoZ, 0to9.

For ANDROIDFRONT/ANDROIDREAR/ANDROID source

Press to enter character search.

(applicable only for CD, USB FRONT, USB REAR, USB, ANDROID

(applicable only for iPod FRONT, iPod REAR, iPod USB,

to select the desired character (A to Z, 0to9,

2 Press to select the desired character.

^A^ : Upper case (A to Z) _A_ : Lower case (a to z)

-0- : Numbers (0 to 9)

-OTHERS- : Character other than A to Z, 0 to 9

3 Press to start searching.

• To return to the previous setting item, press

• To cancel, press and hold

Pandora®

Preparation:

Install the latest version of the Pandora application on your device (iPhone/iPod touch), then create an account and log in to Pandora.

• Select

[ON]

for

[PANDORA SRC]

Start listening

Open the Pandora application on your device.

2 Connect your device to the USB input terminal.

USB input terminal

KD-R988BTS

cable from the rear of the unit.

: You can also connect to the USB

3 Press repeatedly to select PANDORA FRONT/PANDORA

REAR/PANDORA.

Broadcast starts automatically.

To On the faceplate On the remote control

Playback/pause Press .

Skip a track

Thumbs up or thumbs

down*

Do not leave the cable inside the car when not using.

If thumbs down is selected, the current track is skipped.

[SOURCE SELECT]. ( 4)

Accessory of the iPod/iPhone

and/or

Press T. Press I.

Press . Press .

Press

Create and store a new station

Press .

2 Press to select 3 Press to select

A new station is created based on the current song or artist.

[NEW STATION] [FROM TRACK]

, then press .

[FROM ARTIST]

, then press

4 Press and hold one of the number buttons (3, 4, 5 or 6) to store.

To select a stored station: Press one of the number buttons (3, 4, 5 or 6).

Search for a registered station

Press .

2 Press to select an item, then press .

[BY DATE]:

According to the registered date

[A-Z]:

By alphabetical order

3 Press to select the desired station, then press

To cancel, press and hold .

Bookmark current song information

Press and hold .

“BOOKMARKED” appears and the information is stored to your device.

• The bookmark is available on your Pandora account but not on this unit.

ENGLISH

iHeartRadio®

Preparation:

Install the latest version of iHeartAuto application on your device (iPhone/iPod touch), then create an account and log in to iHeartRadio.

• Select

[ON]

for

[IHEART SRC]

Start listening

Open the iHeartAuto application on your device.

2 Connect your device to the USB input terminal.

USB input terminal

KD-R988BTS

cable from the rear of the unit.

: You can also connect to the USB

3 Press repeatedly to select IHEARTRADIO-F/ IHEARTRADIO-R/

IHEARTRADIO.

Broadcast starts automatically

Do not leave the cable inside the car when not using.

[SOURCE SELECT]. ( 4)

Accessory of the iPod/iPhone

and/or

To On the faceplate On the remote control

Playback/pause Press .

Skip a track for custom station

Thumbs up or thumbs down

Create a new/ custom station

Scan for live station

Press T. Press I.

Press

Press and hold

. Press .

1 Press 3 to start

scanning.

2 Press 3 again to listen

to the station.

Press

( Not available )

Search and store a station

Press .

2 Press to select a category, then press . 3 Press to select the desired station, then press

When a city list appears, you can search cities in alphabetical order by

pressing

To cancel, press and hold .

To store a station: Press and hold one of the number buttons (4, 5 or 6). To select a stored station: Press one of the number buttons (4, 5 or 6).

quickly.

ENGLISH

SiriusXM® Radio

Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required. For more information, visit <www.siriusxm.com>.

Preparation:

(for KD-R988BTS)

1 Connect the optional SiriusXM Vehicle Tuner

(commercially available).

Antenna

Expansion port on the rear panel

SiriusXM Vehicle Tuner

2 Check your Radio ID for activation.

The SiriusXM Radio ID is required for activation and

can be found by tuning to Channel 0 as well as on the label found on the SiriusXM Vehicle Tuner and its packaging.

The Radio ID does not include the letters I, O, S or F.

3 Activate the subscription.

For users in the U.S.A.:

Online: Go to <www.siriusxm.com> Phone: Call 1-866-635-2349

For users in Canada:

Online: Go to <www.siriusxm.ca/activatexm> Phone: Call 1-877-438-9677 4 Press repeatedly to select SIRIUSXM to

start updating.

Start listening

Press repeatedly to select SIRIUSXM.

2 Press .

“

” lights up.

3 Press to select a CATEGORY, then press . 4 Press to select a category from the list, then press .

If “ALL CHANNELS” is selected, all the available channels will be shown.

5 Press to select a channel, then press . (or) Press to search for a channel manually.

• Pressing and holding changes the channel rapidly.

If a locked channel or a mature channel is selected, a pass code input screen appears. Enter the pass code to receive the channel.

( 13)

Settings in memory

You can store up to 18 channels.

Store a channel

While listening to a channel....

Press and hold one of the number buttons (1 to 6).

(or) 1 Press and hold until “PRESETMODE” flashes. 2 Press to select a preset number, then press .

The preset number flashes and “MEMORY” appears.

Select a stored channel

Press one of the number buttons (1to6).

(or) 1 Press . 2 Press to select PRESET, then press . 3 Press to select a preset number, then press . (or)

Press

on the remote control.

ENGLISH

SiriusXM® Radio

(for KD-R988BTS)

SiriusXM Replay™

While listening to a channel....

1 Press .

“

” lights up and the unit memorizes this paused position.

2 Press to start Replay.

Replay starts from the paused position in step

During Replay...

To On the faceplate On the remote control

Playback/pause Press .

Skip the current song backward/forward

Rewind/Fast-forward Press and hold

Go to Live and exit Replay

Press

Press and hold

Press

Press and hold

1 Press . 2 Press to

select LIVE, then press

SmartFavorites and TuneStart™

User preset channels are initially assigned as the SmartFavorites channels. SmartFavorite channel is available with SXV200 or later SiriusXM tuner models. The SiriusXM Vehicle Tuner automatically buffers the broadcast audio content of the SmartFavorites channels in the background.

Using SXV200: This unit can assign a maximum of 6 SmartFavorites channels. If you try to assign the 7th channel, an error beep tone will be heard. Initially, preset channels 1 to 6 are assigned as SmartFavorites.

Using SiriusXM tuner models later than SXV200: This unit can assign a maximum of 18 SmartFavorites channels. Initially, all preset channels are assigned as SmartFavorites.

• “

” appears at the last character of the channel name for the

SmartFavorites channels.

When you select a SmartFavorite channel, you can rewind and replay up to 30 minutes of any of the missed news, talk, sports or music content.

• Playback starts from the beginning of the song if to

[ON] ( 13)

To On the faceplate

Select a stored SmartFavorite

channel

for most music channels stored as a SmartFavorite.

Press one of the number buttons (1to6).

1 Press . 2 Press to select PRESET, then press

[TUNE START]

3 Press to select a preset number,

Cancel SmartFavorites channels

then press

1 Press . 2 Press to select PRESET, then press

3 Press to select a preset number,

Reassign SmartFavorites channels

then press and hold

“

” is removed from the last character.

Repeat steps channels.

“

” appears at the last character.

1 to 3 of cancelling SmartFavorites

is set

ENGLISH

SiriusXM® Radio

(for KD-R988BTS)

TuneScan™

You can get a short preview of the songs that you have missed on each of your SmartFavorites music channels or currently tuned music channel.

1 Press . 2 Press to select TUNE SCAN, then press .

Scanning start for the first 6 seconds of the recorded music contents.

• To listen to the current song, press

to stop scanning. The

unit continues playing the current song.

• To select the previous/next song, press

• To cancel scanning, press and hold

. Playback returns to the

channel before you entered TuneScan.

SiriusXM settings

Press and hold .

2 Press to select an item (see the following table), then

press

3 Repeat step 2 until the desired item is selected/activated or follow

the instructions stated on the selected item.

4 Press to exit.

To return to the previous setting item, press .

Default:

SIRIUS XM

CHANNEL LOCK

To unlock settings:

Press to select a number.

Press to move to the entry position.

Repeat steps 1 and 2 to enter the current pass code.

(Initial pass code is 0000.)

Press to confirm.

CODE SET

Press to enter

Press to select a number.

Press to move to the entry position.

Repeat steps 2 and 3 to enter a new 4-digit pass code.

Press to confirm.

Repeat steps 2 to 5 to reconfirm the pass code.

•

Make a note of the new pass code to enter channel lock settings

[NEW CODE]

for next time.

LOCK SETTING MATURE CH

USER DEFINED

lock.;

CHANNEL EDIT

:Selects the SiriusXM-defined lock setting.;

:Selects the individual channels the user wants to

OFF

:Cancels.

Press to select a category, then press

Press to select a channel you want to lock, then

press

“L” appears in front of the channel number.

Press and hold to exit.

CHANNEL CLEAR

TUNE START

YES

:Clears all the locked channels.; NO:Cancels.

:All qualified music channels in the SmartFavorites will start

playback from the beginning of the song.;

SIGNAL LEVEL

BUFFER USAGE

SXM RESET YES

Displayed only when

Available only if the connected SiriusXM Vehicle Tuner is SXV200 or later that supports

Shows the strength (

NO SIGNAL/WEAK/GOOD/STRONG

current received signal.

Shows the memory usage (0%to

100%

:Resets stored channel and lock setting to default.; NO:Cancels.

[USER DEFINED]

is selected.

SmartFavorites.

OFF

:Cancels.

) for Replay buffer.

) of the

ENGLISH

BLUETOOTH®

BLUETOOTH — Connection

Supported Bluetooth profiles

– Hands-Free Profile (HFP) – Advanced Audio Distribution Profile (A2DP) – Audio/Video Remote Control Profile (AVRCP) – Serial Port Profile (SPP) – Phonebook Access Profile (PBAP)

Supported Bluetooth codecs

– Sub Band Codec (SBC) – Advanced Audio Coding (AAC)

Connect the microphone

MIC (microphone input terminal)

Rear panel

Adjust the microphone angle

For

KD-R888BT

( 35)

: Connect to the microphone input jack.

Microphone (supplied)

Secure using cord clamps (not supplied) if necessary.

Pair and connect a Bluetooth device for the first time

Press to turn on the unit.

2 Search and select “KD-R9 BTS”/“KD-R8 BT” on the Bluetooth device.

“BTPAIRING” flashes on the display.

• For some Bluetooth devices, you may need to enter the Personal Identification Number

(PIN) code immediately after searching.

3 Perform (A) or (B) depending on what appears on the display.

For some Bluetooth devices, pairing sequence may vary from the steps described below.

(A) “[Device Name]”

“XXXXXX” “ENTER–YES” “BACK–NO”

“XXXXXX” is a 6-digit passkey randomly generated during each pairing.

Ensure that the passkeys appear on the unit and Bluetooth device are the same. Press to confirm the passkey. Operate the Bluetooth device to confirm the passkey.

(B) “[Device Name]”

Press to start pairing.

• If “PAIRING” “PIN 0000” scrolls on the display, enter the PIN code “0000” into the Bluetooth device.

• If only “PAIRING” appears, operate the Bluetooth device to confirm pairing. “PAIRING COMPLETED” appears when pairing is completed and “ ” will light up when the

Bluetooth connection is established.

• This unit supports Secure Simple Pairing (SSP).

• Up to five devices can be registered (paired) in total.

• Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you reset the unit. To delete the paired device,

• A maximum of two Bluetooth phones and one Bluetooth audio device can be connected at any time.

However, while in BT AUDIO source, you can connect to five Bluetooth audio devices and

switch between these five devices. (

• Some Bluetooth devices may not automatically connect to the unit after pairing. Connect the device to the unit manually.

• Refer to the instruction manual of the Bluetooth device for more information.

You can change to a desired PIN code before pairing.

“ENTER–YES” “BACK–NO”

18, [DEVICE DELETE]

)

( 18)

ENGLISH

BLUETOOTH®

Auto Pairing

When you connect iPhone/iPod touch/ Android device to the USB input terminal, pairing request (via Bluetooth) is automatically activated.

BLUETOOTH — Mobile phone

Symbolic button

Press confirmed the device name.

Automatic pairing request is activated only if: – Bluetooth function of the connected device is

turned on.

–

[AUTO PAIRING]

– JVC MUSIC PLAY application is installed on

the Android device selected

to pair once you have

is set to

[ON]. ( 18)

( 8)

( 7)

and

[AUTO MODE]

Receive a call

When there is an incoming call:

• The symbolic button will blink in the color you have selected in

• The unit answers the call automatically if During a call:

• The symbolic button stop blinking and illuminate in the color you have selected in

( 16)

• If you turn off the unit or detach the faceplate, the Bluetooth connection is disconnected.

The following operations may differ or not available depending on the connected phone.

To On the faceplate On the remote control

First incoming call...

Answer a call

Reject a call

End a call

Press

Press and hold

[AUTO ANSWER]

or .

[RING COLOR]. ( 16)

is set to a selected time.

Press

Press and hold

( 16)

[RING COLOR]

ENGLISH

BLUETOOTH®

To On the faceplate On the remote control

While talking on the first incoming call...

Answer another incoming call and hold the current call

Reject another incoming call

While having two active calls...

End current call and activate held call

Swap between the current call and held call

Adjust the phone volume

[00]

[35]

(Default:

[15]

Switch between hands-free and private talk modes

This adjustment will not affect the volume of the other sources.

Operations may vary according to the connected Bluetooth device.

Improve the voice quality

While talking on the phone....

1 Press and hold . 2 Press to select an item

3 Repeat step 2 until the desired item is selected or activated. 4 Press to exit.

To return to the previous setting item, press .

Press

Press and hold

Press

Press a call.

)

Press during a call.

(

see the following table), then press

or .

during

( Not available )

Press and hold

( Not available )

MIC GAIN LEVEL –10

to

LEVEL +10(LEVEL –04

):The sensitivity of the

microphone increases as the number increased.

NR LEVEL LEVEL –05

to

LEVEL +05(LEVEL 00

):Adjust the noise reduction level until the least noise is being heard during a phone conversation.

ECHO CANCEL LEVEL –05

to

LEVEL +05(LEVEL 00

):Adjust the echo cancellation delay time until the least echo is being heard during a phone conversation.

Make the settings for receiving a call

Press to enter Bluetooth mode.

1 2 Press to select an item

then press

(

see the following table),

3 Repeat step 2 until the desired item is selected or

activated.

To return to the previous setting item, press

SETTINGS

AUTO ANSWER

01 SEC

to

30 SEC

:The unit answers incoming call

automatically in the selected time (in seconds).;

RING COLOR COLOR 01

to

COLOR 49(COLOR 08

): Selects the illumination color for the symbolic button as notification when there is an incoming call and during a call.;

OFF

:Cancels.

Default:

OFF

:Cancels.

ENGLISH

BLUETOOTH®

Make a call

You can make a call from the call history, phonebook, or dialing the number. Call by voice is also possible if your mobile phone has the feature.

1 Press to enter Bluetooth mode.

“(First device name)” appears.

• If two Bluetooth phones are connected, press again to switch to another

phone.

“(Second device name)” appears. 2 Press to select an item

(

see the following table), then press .

3 Repeat step 2 until the desired item is selected/activated or follow the instructions

stated on the selected item.

To return to the previous setting item, press

RECENT CALL

PHONEBOOK

DIAL NUMBER1 Press to select a number (0 to 9) or character ( , #, +).

VOICE

(Applicable only if the phone supports PBAP.)

Press to select a name or a phone number.

• “<” indicates call received, “>“ indicates call made, “M” indicates call missed.

• “NO HISTORY” appears if there is no recorded call history or call number.

Press to call.

(Applicable only if the phone supports PBAP.)

Press to select the desired letter (A to Z, 0to9, and OTHERS).

• “OTHERS” appears if the first character is other than Ato Z, 0 to 9.

Press to select a name, then press .

Press to select a phone number, then press to call.

•

The phonebook of the connected phone is automatically transferred to the unit when pairing.

•

This unit can display only non-accent letters. (Accent letters such as “Ú” is showns as “U”.)

Press to move the entry position.

Repeat steps

Press to call.

Speak the name of the contact you want to call or the voice command to control the phone functions.

and 2 until you finish entering the phone number.

( Make a call using voice recognition)

Make a call using voice recognition

Press and hold to activate the connected

phone.

2 Speak the name of the contact you want to call or

the voice command to control the phone functions.

• Supported Voice Recognition features vary for each phone. Refer to the instruction manual of the connected phone for details.

• This unit also supports the intelligent personal assistant function of iPhone.

Settings in memory

Store a contact in memory

You can store up to 6 contacts into the number buttons (1 to 6).

1 Press to enter Bluetooth mode. 2 Press to select

[DIAL NUMBER]

, then press .

[RECENT CALL], [PHONEBOOK]

3 Press to select a contact or enter a phone

number.

If a contact is selected, press

phone number.

to show the

4 Press and hold one of the number buttons (1 to 6).

“MEMORY P(selected preset number)” appears when

the contact is stored.

To erase a contact from the preset memory, select

[DIAL NUMBER]

in step 2 and store a blank number.

Make a call from memory

Press to enter Bluetooth mode.

1 2 Press one of the number buttons (1 to 6). 3 Press to call.

“NO PRESET” appears if there is no contact stored.

ENGLISH

BLUETOOTH®

Bluetooth mode settings

Press and hold .

2 Press to select an item

(

see the following table), then press .

3 Repeat step 2 until the desired item is selected/activated or follow the instructions

stated on the selected item.

4 Press to exit.

To return to the previous setting item, press .

Default:

BT MODE

PHONE SELECT

AUDIO SELECT

DEVICE DELETE

PIN CODE EDIT (0000)

RECONNECT ON

AUTO PAIRING ON

INITIALIZE YES

INFORMATION MYBTNAME

You can only connect a maximum of two Bluetooth phones and one Bluetooth audio device at any time.

Selects the phone or audio device to connect or disconnect. “

” appears in front of the device name when connected.

“

” appears in front of the current playback audio device.

Press to select a device to delete, then press .

Press to select

Changes the PIN code (up to 6 digits).

Press to select a number.

Press to move the entry position.

Repeat steps

Press to confirm.

:The unit automatically reconnect when the last connected Bluetooth device is within range.;

OFF

:Cancels.

:The unit automatically pair supported Bluetooth device (iPhone/iPod touch/Android device) when it is connected through USB input terminal.Depending on the operating system of the connected device, this function may not work. ;

:Initializes all the Bluetooth settings (including stored pairing, phonebook, and etc.).;

:Cancels.

address of this unit.

and 2 until you finish entering the PIN code.

: Displays the unit name (“KD-R9 BTS”/“KD-R8 BT”).; MY

[YES]

[NO]

, then press .

OFF

:Cancels.

ADDRESS

: Shows

Bluetooth compatibility check mode

You can check the connectivity of the supported profile between the Bluetooth device and the unit.

• Make sure there is no Bluetooth device paired.

1 Press and hold .

“BLUETOOTH”

“SEARCH NOW USING PHONE” scrolls on the display.

2 Search and select “KD-R9 BTS”/“KD-R8 BT”

on the Bluetooth device within 3minutes.

“CHECK MODE” appears.

“PIN IS 0000”

3 Perform (A), (B) or (C) depending on what

appears on the display.

(A) “PAIRING”

Ensure that the same passkey appears on the unit and Bluetooth device, then operate the Bluetooth device to confirm the passkey.

(B) “PAIRING”

the Bluetooth device.

confirm pairing.

After pairing is successful, “PAIRING OK” Name]” appears and Bluetooth compatibility check starts. If “CONNECT NOW USING PHONE” appears, operate the Bluetooth device to allow phonebook access to continue. “TESTING” flashes on the display.

“XXXXXX” (6-digit passkey):

“PIN IS 0000”: Enter “0000” on

“[Device

ENGLISH

BLUETOOTH®

The connectivity result flashes on the display.

“PAIRING OK” and/or “HANDS-FREE OK” or “AUD.STREAM OK”

and/or “PBAP OK”

Compatible

Compatible with Hands-Free Profile (HFP)

Compatible with Advanced Audio Distribution Profile (A2DP)

Compatible with Phonebook Access profile (PBAP)

After 30 seconds, “PAIRING DELETED” appears to indicate that pairing has been deleted, and the unit exits check mode.

• To cancel, press and hold power, then turn on the power again.

and/

to turn off the

BLUETOOTH — Audio

While in BT AUDIO source, you can connect to five Bluetooth audio devices and switch between these five devices.

Audio player via Bluetooth

Press repeatedly to select BTAUDIO (or press SOURCE on the remote control).

• Pressing enters BT AUDIO directly. 2 Operate the Bluetooth audio player to start playback.

To On the faceplate On the remote control

Playback/pause

Select group or folder Press

Reverse skip/Forward skip Press

Reverse/Fast-forward Press and hold

Repeat play Press

Random play

Select a file from a folder/list Refer to “Select a file from a folder/list”

Switch between connected Bluetooth audio devices

Pressing the “Play” key on the connected device itself also causes switching of sound output from the device.

Press

. Press .

repeatedly.

TRACK REPEAT/ALL REPEAT/REPEAT OFF

Press

repeatedly.

GROUP RANDOM/ALL RANDOM/RANDOM OFF

on page 8.

Press 5.

Press

Press and hold

( Not available )

Operations and display indications may differ according to their availability on the connected device.

ENGLISH

BLUETOOTH®

Settings to use JVC Remote application

JVC Remote application is designed to control the JVC car receiver’s operations from iPhone/iPod (via Bluetooth or via USB input terminal) or Android smartphone (via Bluetooth).

Preparation:

Install the latest version of JVC Remote application on your device before connecting. For more information, visit <http://www.jvc.net/cs/car/>.

1 Press and hold . 2 Press to select an item

press

(

see the following table), then

3 Repeat step 2 until the desired item is selected or activated. 4 Press to exit.

To return to the previous setting item, press .

Default:

REMOTE APP

SELECT

IOS YES

ANDROID YES

ANDROID LIST*:Selects the Android smartphone to use from the list.

Displayed only when

Select the device (IOS or ANDROID) to use the application.

:Selects iPhone/iPod to use the application via Bluetooth or connected via USB input terminal.; If IOS is selected, select iPod BT source (or iPod USB if your iPhone/iPod is connected via USB input terminal) to activate the application.

•

The connectivity of the application will be interrupted or disconnected if:

– You change from iPod BT source to any playback source connected via

the USB input terminal.

– You change from iPod USB source to iPod BT source.

:Selects Android smartphone to use the application via Bluetooth.;

:Cancels.

[ANDROID]

[SELECT]

:Cancels.

is set to

[YES]

STATUS

Shows the status of the selected device.

IOS CONNECTED

connected via Bluetooth or USB input terminal.

IOS NOT CONNECTED ANDROID CONNECTED

smartphone connected via Bluetooth.

ANDROID NOT CONNECTED

application.

: You are able to use the application using the iPhone/iPod

: No IOS device is connected to use the application.

: You are able to use the application using the Android

: No Android device is connected to use the

Listen to iPhone/iPod via Bluetooth

You can listen to the songs on the iPhone/iPod via Bluetooth on this unit.

Press repeatedly to select iPodBT.

• You can operate the iPod/iPhone in the same way as iPod/iPhone via USB input terminal.

• If you plug in an iPhone/iPod to the USB input terminal while listening to iPodBT source, the source automatically change to iPodUSB. Press

to select iPodBT if the device is still connected via Bluetooth.

( 7)

ENGLISH

BLUETOOTH®

AUX

Internet radio via Bluetooth

You can listen to internet radio (Pandora and iHeartRadio) on iPhone/ iPod touch/Android device via Bluetooth on this unit.

• Make sure the USB input terminal is not connected to any device.

Listen to Pandora

Preparation:

Select

[ON]

for

[PANDORA SRC]

[SOURCE SELECT]. ( 4)

1 Open the Pandora application on your device. 2 Connect your device via Bluetooth connection.

( 14)

3 Press repeatedly to select PANDORA (for iPhone/iPod) or

PANDORA BT (for Android device).

The source switches and broadcast starts automatically.

• You can operate Pandora in the same way as Pandora via USB input terminal.

( 9)

Listen to iHeartRadio

Preparation:

Select

[ON]

for

[IHEART SRC]

[SOURCE SELECT]. ( 4)

1 Open the iHeartAuto application on your device. 2 Connect your device via Bluetooth connection.

( 14)

3 Press repeatedly to select IHEARTRADIO.

The source switches and broadcast starts automatically.

• You can operate iHeartRadio in the same way as iHeartRadio via USB input terminal.

( 10)

Use a portable audio player

Connect a portable audio player (commercially available).

Auxiliary input jack

Portable audio player

3.5mm (1/8") stereo mini plug with “L”

2 Select

shaped connector (commercially available)

[ON]

for

[BUILT-IN AUX]

[SOURCE SELECT]. ( 4)

3 Press repeatedly to select AUX. 4 Turn on the portable audio player and start playback.

Use a 3-core plug head stereo mini plug for optimum audio output.

ENGLISH

AUDIO SETTINGS

1 Press and hold . 2 Press to select an item (see the following table), then

press

3 Repeat step 2 until the desired item is selected/activated or follow

the instructions stated on the selected item.

4 Press to exit.

To return to the previous setting item, press .

Default:

EQ SETTING

PRESET EQ

Select a preset equalizer suitable to the music genre.

•

Select

[USER]

to use the settings made in

[EASY EQ]

[PRO EQ]

FLAT/DRVN 3/DRVN 2/DRVN 1/HARD ROCK/HIP HOP/JAZZ/POP

R&B/USER/CLASSICAL

Drive equalizer (

DRVN 3/DRVN 2/DRVN 1)

boosts specific frequencies in the audio signal to reduce the noise heard from outside the car or running noise of the tyres.

EASY EQ

Adjust your own sound settings.

•

The settings are stored to

•

The settings made may affect the current settings of

*1*

SUB.W SP SUB.W BASS MID TRE

: 00to

*1*

[USER]

+06

(Default:

–50

to

+10

LVL–09

to

LVL+09

to to

LVL+09 LVL+09

LVL–09 LVL–09

[PRO EQ]

03 00 LVL 00 LVL 00 LVL 00

)

PRO EQ

Adjust your own sound settings.

•

The settings are stored to

•

The settings made may affect the current settings of

[USER]

62.5HZ

LEVEL –09

to

LEVEL +09 (LEVEL 00)

: Adjusts the level to memorize for each source.

(Before making an adjustment, select the source you want to adjust.)

:Turns on the extended bass.;

OFF

:Cancels.

100HZ/160HZ/250HZ/400HZ/630HZ/1KHZ/1.6KHZ/2.5KHZ/4KHZ/6.3KHZ/10KHZ 16kHZ

LEVEL –09

to

LEVEL +09 (LEVEL 00):

Adjusts the level to memorize for each source.

(Before making an adjustment, select the source you want to adjust.)

Q FACTOR 1.35/1.50/2.00

AUDIO CONTROL

BASS BOOST

LOUDNESS LEVEL 01/LEVEL 02

SUB.W LEVEL

LEVEL +01 OFF

:Cancels.

balanced sound at low volume.;

SPK-OUT

:Adjust the quality factor.

to

LEVEL +05

: Selects your preferred bass boost level.;

:Boosts low or high frequencies to produce a well-

OFF

:Cancels.

(Not applicable when 3-way crossover is selected.)

SUB.W 00

to

SUB.W +06(SUB.W +03

output level of the subwoofer connected via speaker lead.

( 35)

PRE-OUT

SUB.W –50

to

SUB.W +10(SUB.W 00

output level of the subwoofer connected to the lineout terminals (SW or REAR/SW) through an external amplifier.

( 35)

SUBWOOFER

SET

1, *2, *3:

( 23)

: Turns on the subwoofer output.;

OFF

:Cancels.

[EASY EQ]

):Adjusts the

ENGLISH

AUDIO SETTINGS

FADER

(Not applicable when 3-way crossover is selected.)

POSITION R15

rear speaker output balance.

BALANCE

POSITION L15

right speaker output balance.

VOLUMEADJUST LEVEL –15

of each source (compared to the FM volume level). Before adjustment, select the source you want to adjust.

AMPGAIN LOWPOWER

the maximum power of each speaker is less than 50W to prevent damaging the speakers.); is 35.

SPK/PREOUT

(Not applicable when 3-way crossover is selected.) Depending on the speaker connection method, select the appropriate setting to get the desired output.

SPEAKER SIZE

X ' OVER

DTA SETTINGS

CAR SETTINGS

X ' OVER TYPE Caution

Depending on the crossover type you have selected (see

TYPE]

below), 2-way crossover or 3-way crossover setting items will be

shown.

( 25, Crossover settings)

By default, 2-way crossover type is selected.

For settings,

: Adjust the volume before changing the

avoid the sudden increase or decrease of the output level.

2-WAY

3-WAY

(Displayed only when

YES

:Selects two way crossover type.; NO:Cancels.

(Displayed only when

YES

:Selects three way crossover type.; NO:Cancels.

to

POSITION F15(POSITION 00

to

POSITION R15(POSITION 00

to

LEVEL +06(LEVEL 00

):Adjusts the front and

):Adjusts the left and

):Preset the initial volume level

:Limits the maximum volume level to 25. (Select if

HIGH POWER

:The maximum volume level

( 24, Speaker output settings)

26, Digital Time Alignment settings

[X ' OVER TYPE]

[3-WAY]

is selected.)

[2-WAY]

is selected.)

[X ' OVER

SOUND EFFECT

SPACE ENHANCE

(Not applicable for TUNER source.)

SND RESPONSE LEVEL1/LEVEL2/LEVEL3

SOUND LIFT LOW/MIDDLE/HIGH

VOL LINK EQ ON

K2 TECHNOLOGY

Displayed only when

For 2-way crossover: Displayed only when

( 24)

For 2-way crossover: Displayed only when

[SUB.W/SUB.W]. ( 24)

This adjustment will not affect the subwoofer output.

SMALL/MEDIUM/LARGE OFF

:Cancels.

: Virtually enhances the sound space.;

: Virtually makes the sound more realistic.;

OFF

:Cancels.

: Virtually adjust the sound position heard from

the speakers.;

OFF

:Cancels.

:Boosts the frequency to reduce the noise heard from outside the car

or running noise of the tyres.;

OFF

:Cancels.

(Not applicable for TUNER source, SIRIUS XM source and AUX source.)

:Improve the sound quality of compressed music.;

[SUBWOOFER SET]

is set to

[ON]. ( 22)

[SPK/PRE OUT]

is set to

OFF

:Cancels.

[SUB.W/SUB.W]

[REAR/SUB.W]

ENGLISH

AUDIO SETTINGS

Speaker output settings

(Applicable only if [X ' OVER TYPE ] is set to [2-WAY]) (

Select the output setting for the speakers speaker connection method.

[SPK/PRE OUT]

Connection via lineout terminals

For connections through an external amplifier.

KD-R988BTS

Setting on

[SPK/PRE OUT]

REAR/REAR

(default)

REAR/SUB.W

SUB.W/SUB.W

KD-R888BT

Setting on

[SPK/PRE OUT]

REAR/REAR

REAR/SUB.W

SUB.W/SUB.W

Audio signal through lineout terminal

FRONT REAR SW

Front speakers output Rear speakers output Subwoofer output

( Not available ) ( Not available ) ( Not available )

Front speakers output L (left): Subwoofer

output R (right): (Mute)

Audio signal through lineout terminal

FRONT REAR/SW

Front speakers output Rear speakers output

(default) Front speakers output Subwoofer output

Front speakers output Subwoofer output

23)

( 35)

, based on the

Subwoofer output

Connection via speaker leads

For connections without using an external amplifier. However, with this settings you can also enjoy the subwoofer output.

Setting on

[SPK/PRE OUT]

REAR/REAR

REAR/SUB.W

SUB.W/SUB.W

[SUB.W/SUB.W]

–

[120HZ]

–

[POSITION R02] R15]

to

is selected:

is selected in

[POSITION 00]

[SUBWOOFER LPF]

Audio signal through rear speaker lead

L (left) R (right)

Rear speakers output Rear speakers output

Subwoofer output (Mute)

and

[FADER]

and selectable range is

[THROUGH]

( 35)

is not available.

[POSITION

ENGLISH

AUDIO SETTINGS

Crossover settings

Below are the available setting items for 2-way crossover and 3-way crossover.

Caution

Select a crossover type according to how the speakers are connected.

( 35)

If you select a wrong type:

• The speakers may damage.

• The output sound level may be extremely high or low.

SPEAKER SIZE

Selects according to the connected speaker size for optimum performance.

•

The frequency and slope settings are automatically set for the crossover of the selected speaker.

•

When 2-way crossover is selected, if of

[FRONT], [REAR]

and

[SUBWOOFER]

[NONE]

for

[SPEAKER SIZE]

is selected for

, the

[TWEETER]

[X ‘ OVER]

setting of the selected speaker is not available.

• When 3-way crossover is selected, if of

[SPEAKER SIZE]

X ‘ OVER

(crossover)

, the

[X’OVER]

• [FRQ]/[F-HPF FRQ]/[R-HPF FRQ]/[SW LPF FRQ]/[HPF FRQ]/[LPF FRQ]

setting of

[NONE]

[WOOFER]

is selected for

is not available.

[WOOFER]

: Adjusts the crossover frequency for the selected speakers (high pass filter or low pass filter).

[THROUGH]

• [SLOPE]/[F-HPF SLOPE]/[R-HPF SLOPE]/[SW LPF SLOPE]/[HPF SLOPE] [LPF SLOPE]:

Selectable only if a setting other than

is selected, all signals are sent to the selected speakers.

Adjusts the crossover slope.

[THROUGH]

is selected for the

crossover frequency.

• [SW LPF PHASE]/[PHASE]:

Selects the phase of the speaker output to

be in line with the other speaker output.

•

[GAIN LEFT]/[GAIN RIGHT]/[F-HPF GAIN]/[R-HPF GAIN]/[SW LPF GAIN]/[GAIN]:

Adjusts the output volume of the selected speaker.

2-way crossover setting items

SPEAKER SIZE

FRONT SIZE

TWEETER

REAR

3.5"/4"/4.75"/5"/6.5"/6.75"/7"/4×6/5×7/6×8/6×9/7×10 NONE

SUBWOOFER

*2*

6.5"/8"/10"/12"/15" OVER/NONE

X ' OVER

TWEETER FRQ

GAIN LEFT

GAIN RIGHT

FRONT HPF F-HPF FRQ

F-HPF SLOPE

F-HPF GAIN

REAR HPF

R-HPF FRQ 30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ/100HZ

R-HPF SLOPE

R-HPF GAIN

SUBWOOFER

*2*

LPF

SW LPF FRQ 30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ/100HZ

SW LPF SLOPE

SW LPF PHASE

SW LPF GAIN –08DB

1, *2, *3:

( 26)

(not connected)

3.5"/4"/4.75"/5"/6.5"/6.75"/7"/4×6/5×7/6×8/ 6×9/7×10

SMALL/MIDDLE/LARGE/NONE

(not connected)

(not connected)

1KHZ/1.6KHZ/2.5KHZ/4KHZ/5KHZ/6.3KHZ/8KHZ/ 10KHZ/12.5KHZ

–08DB

00DB

–08DB

00DB

30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ/100HZ 120HZ/150HZ/180HZ/220HZ/250HZ/THROUGH

–06DB/–12DB/–18DB/–24DB

–08DB

00DB

120HZ/150HZ/180HZ/220HZ/250HZ/THROUGH

–06DB/–12DB/–18DB/–24DB

–08DB

00DB

120HZ/150HZ/180HZ/220HZ/250HZ/THROUGH

–06DB/–12DB/–18DB/–24DB

REVERSE

(180°)/

NORMAL

(0°)

00DB

ENGLISH

AUDIO SETTINGS

3-way crossover setting items

SPEAKER SIZE

TWEETER

MID RANGE

WOOFER

SMALL/MIDDLE/LARGE

3.5"/4"/4.75"/5"/6.5"/6.75"/7"/4×6/5×7/6×8/6×9

6.5"/8"/10"/12"/15" OVER/NONE

X ' OVER

TWEETER HPF FRQ

1KHZ/1.6KHZ/2.5KHZ/4KHZ/5KHZ/6.3KHZ/8KHZ 10KHZ/12.5KHZ

SLOPE

PHASE

–06DB/–12DB

REVERSE

GAIN –08DB

MID RANGE HPF FRQ

30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ/100HZ 120HZ/150HZ/180HZ/220HZ/250HZ/THROUGH

HPF SLOPE

LPF FRQ

–06DB/–12DB

1KHZ/1.6KHZ/2.5KHZ/4KHZ/5KHZ/6.3KHZ/8KHZ 10KHZ/12.5KHZ/THROUGH

LPF SLOPE

PHASE

–06DB/–12DB

REVERSE

GAIN –08DB

WOOFER

LPF FRQ 30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ/100HZ

120HZ/150HZ/180HZ/220HZ/250HZ/THROUGH

SLOPE

PHASE

–06DB/–12DB

REVERSE

GAIN –08DB

Displayed only when

KD-R888BT [SUB.W/SUB.W]. ( 24)

Displayed only when

ENGLISH

[SPK/PRE OUT]

: Displayed only when

[SUBWOOFER SET]

(180°)/

00DB

(180°)/

00DB

(180°)/

00DB

is set to

[REAR/REAR]

[SPK/PRE OUT]

is set to

(not connected)

NORMAL

is set to

[REAR/SUB.W]

[ON]. ( 22)

(0°)

[REAR/SUB.W]. ( 24)

Digital Time Alignment settings

Digital Time Alignment sets the delay time of the speaker output to create a more suitable environment for your vehicle.

• For more information,

of [DTA SETTINGS]

27, Determining the value for [DISTANCE] and [GAIN]

DTA SETTINGS

POSITION

Selects your listening position (reference point).

ALL

:Not compensating;

FRONT LEFT

•

[FRONT ALL]

FRONT RIGHT:

:Front left seat;

is displayed only when

FRONT ALL

[2-WAY]. ( 23)

CAR SETTINGS

DISTANCE

GAIN

DTA RESET YES

0FT

20.01FT

:Fine adjust the distance to compensate.

–8DB

0DB

:Fine adjust the output volume of the selected

speaker.

:Resets the settings (

[POSITION]

to default.; NO:Cancels.

[DISTANCE]

and

Identify your car type and rear speaker location in order to make the adjustment for

[DTA SETTINGS]

CAR TYPE COMPACT/FULL SIZE CAR/WAGON/MINIVAN/SUV

MINIVAN(LONG)

:Selects the type of vehicle.;

compensating.

R-SP LOCATION

Selects the location of the rear speakers in your vehicle to calculate the furthest distance from the listening position selected (reference point).

•

1, *2:

( 27)

DOOR/REAR DECK

[OFF], [COMPACT], [FULL SIZE CAR], [WAGON]

•

2ND ROW/3RD ROW

selected as

:Selectable only when

[MINIVAN]

:Selectable only when

[MINIVAN(LONG)]

Front right seat;

:Front seat

[X ' OVER TYPE]

[GAIN]

) of the selected

OFF:

[CAR TYPE]

Not

is set to

is selected

[SUV]

+ 86 hidden pages

JVC KD-R988BTS, KD-R888BT Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual