JVC KD-G120R, KD-G120 User Manual

Download

Page 1

CD RECEIVER KD-G120R/KD-G120

ENGLISH

RECEPTOR CON CD KD-G120R/KD-G120

RECEPTEUR CD KD-G120R/KD-G120

KD-G120R

KD-G120

For canceling the display demonstration, see page 6. Para cancelar la demostración en pantalla, consulte la página 6. Pour annuler la démonstration des affichages, référez-vous à la page 6.

For installation and connections, refer to the separate manual. Para la instalación y las conexiones, refiérase al manual separado. Pour l’installation et les raccordements, se référer au manuel séparé.

INSTRUCTIONS

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

For customer Use:

Enter below the Model No. and Serial No. which are located on the top or bottom of the cabinet. Retain this information for future reference.

Model No.

Serial No.

ESPAÑOL

FRANÇAIS

GET0330-001A

[J]

Page 2

Thank you for purchasing a JVC product.

Please read all instructions carefully

before operation, to ensure your complete

understanding and to obtain the best possible

performance from the unit.

ENGLISH

INFORMATION (For U.S.A.)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna. – Increase the separation between the

equipment and receiver.

– Connect the equipment into an outlet on

a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/

TV technician for help.

Warning:

If you need to operate the unit while driving, be sure to look ahead carefully or you may be involved in a traffic accident.

How to reset your unit

• Your preset adjustments will also be erased.

• If a disc is loaded, it will eject. Be careful not to drop the disc.

How to forcibly eject a disc

• If this does not work, reset your unit.

• Be careful not to drop the disc when it ejects.

How to use the M MODE button

If you press M MODE, the unit goes into functions mode, then the number buttons work as different function buttons.

Ex.: When number button 2 works as

MO (monaural) button.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel.

3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam.

Time countdown indicator

To use these buttons for their original functions again after pressing M MODE, wait

for 5 seconds without pressing any of these buttons until the functions mode is cleared or press M MODE again.

Page 3

How to read this manual

• Button operations are mainly explained with the illustrations in the table below.

•

is used to indicate an indicator is

displayed for the corresponding operation.

• Some related tips and notes are explained in “More about this unit” (see pages 11 and 12).

Press briefly.

Press repeatedly.

Press either one.

Press and hold until your desired response begins.

Press and hold both buttons at the same time.

How to detach/attach the control

panel

Detaching...

Control panel — KD-G120R and KD-G120 ....... 4

Remote controller —

Getting started ................................. 6

Basic operations .................................................... 6

Radio operations .............................. 7

Disc operations ................................. 8

Playing a disc in the unit ....................................... 8

Sound adjustments ........................... 9

General settings — PSM ................... 9

Maintenance .................................... 10

More about this unit ......................... 11

Troubleshooting ............................... 12

Specifications ................................... 13

Caution on volume setting:

Discs produce very little noise compared with other sources. Lower the volume before playing a disc to avoid damaging the speakers by the sudden increase of the output level.

RM-RK50 .............. 5

ENGLISH

Attaching...

For safety...

• Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.

• Stop the car before performing any complicated operations.

Temperature inside the car...

If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes normal before operating the unit.

Page 4

Control panel — KD-G120R and KD-G120

Parts identification

ENGLISH

1 (standby/on/attenuator) button 2 SOURCE button 3 BAND button 4 Remote sensor—Only for KD-G120R

• DO NOT expose the remote sensor to strong light (direct sunlight or artificial lighting).

5 Loading slot 6 Display window 7 0 (eject) button 8 EQ (equalizer) button 9

¢/4 buttons

p Control dial q SEL (select) button w DISP (display) button e MO (monaural) button r SSM (Strong-station Sequential Memory)

button

t Number buttons y RPT (repeat) button

Display window

u RND (random) button i M MODE button o

(control panel release) button

Display window

; DISC indicator a RND s RPT (repeat) indicator d S. BASS (super bass) indicator f EQ (equalizer) indicator g Sound mode (C-EQ: custom equalizer)

indicators—JAZZ, CLASSIC, HIP HOP, POPS, ROCK, USER

h Source display Volume level indicator Time countdown indicator

j Main display k Tuner reception indicators— ST (stereo),

MO (monaural)

(disc random) indicator

Page 5

Remote controller — RM-RK50

• RM-RK50 is supplied only for KD-G120R.

Main elements and features

Installing the lithium coin battery

(CR2025)

Aim the remote controller directly at the remote sensor on the unit. Make sure there is no obstacle in between.

Warning:

• Do not install any battery other than CR2025 or its equivalent; otherwise, it may explode.

• Store the battery in a place where children cannot reach to avoid risk of accident.

• To prevent the battery from over-heating, cracking, or starting a fire:

– Do not recharge, short, disassemble,

heat the battery, or dispose of it in a fire.

– Do not leave the battery with other

metallic materials.

– Do not poke the battery with tweezers or

similar tools.

– Wrap the battery with tape and insulate

when throwing away or saving it.

ENGLISH

1 (standby/on/attenuator) button

• Turns the power on if pressed briefly or attenuates the sound when power is on.

• Turns the power off if pressed and held.

2 5 U (up) / D (down) ∞ buttons

• Changes the FM/AM bands with 5 U only.

• Changes the preset stations with D ∞ only.

3 VOL – / VOL + buttons

• Adjusts the volume level.

4 SOUND button

• Selects the sound mode (C-EQ: custom equalizer).

5 SOURCE button

• Selects the source.

6 2 R (reverse) / F (forward) 3 buttons

• Searches for stations if pressed briefly.

• Fast-forwards or reverses the track if pressed and held.

• Changes the tracks of the disc if pressed briefly.

Caution:

Page 6

Getting started

Basic operations

Basic settings

• See also “General settings — PSM” on pages 9 and 10.

~ Turn on the power.

ENGLISH

* You cannot select “DISC” as the

playback source if there is no disc in the loading slot.

! For FM/AM tuner

⁄ Adjust the volume.

Volume level indicator

Volume level appears

@ Adjust the sound as you want. (See

page 9.)

To drop the volume in a moment (ATT)

To restore the sound, press it again.

To turn off the power

1 Canceling the display

demonstrations

Select “DEMO,” then “DEMO OFF.”

2 Setting the clock

Select “CLOCK H” (hour), then adjust the hour. Select “CLOCK M” (minute), then adjust the minute.

3 Finish the procedure.

To check the current clock time while...

The power is turned off

Listening to the radio/a disc

Frequency/Elapsed playing time Ô Clock

Page 7

Radio operations

Reception improves, but stereo effect will be lost. To restore the stereo effect, repeat the same procedure “MONO OFF” appears and the MO indicator goes off.

ENGLISH

Storing stations in memory

You can preset six stations for each band.

Lights up when receiving an FM stereo broadcast with sufficient signal strength.

Selected band appears.

! Start searching for a station.

When a station is received, searching stops. To stop searching, press the same button again.

To tune in to a station manually

In step ! above... 1

2 Select the desired station frequencies.

FM station automatic presetting —

SSM (Strong-station Sequential Memory)

1 Select the FM band (FM1 – FM3) you

want to store into.

“SSM” flashes, then disappears when automatic presetting is over.

Local FM stations with the strongest signals are searched and stored automatically in the FM band.

Manual presetting

Ex.: Storing FM station of 92.5 MHz into preset

number 4 of the FM1 band.

When an FM stereo broadcast is hard to receive

Lights up when monaural mode is activated.

To be continued...

Page 8

ENGLISH

Listening to a preset station

To locate a particular track directly

To select a number from 01 – 06:

Preset number flashes for a while.

To select a number from 07 – 12:

2 Select the preset station (1 – 6) you

want.

Disc operations

Playing a disc in the unit

All tracks will be played repeatedly until you change the source or eject the disc.

To stop play and eject the disc

To fast-forward or reverse the track

Prohibiting disc ejection

You can lock a disc in the loading slot.

To cancel the prohibition, repeat the same procedure.

Selecting the playback modes

You can use only one of the following playback modes at a time.

2 Select your desired playback mode.

7 Repeat play

Mode Plays repeatedly

TRK RPT : The current track. RPT OFF : Cancels.

7 Random play

To go to the next or previous tracks

Mode Plays at random

DISC RND : All tracks of the current disc.

RND OFF : Cancels.

Page 9

Sound adjustments

You can select a preset sound mode suitable to the music genre (C-EQ: custom equalizer).

Preset values

Indication (For)

USER (Flat sound)

ROCK

(Rock or disco music)

CLASSIC

(Classical music)

POPS (Light music)

HIP HOP

(Funk or rap music)

JAZZ (Jazz music)

BAS TRE S.BS

(bass) (treble)

00 00 OFF

+03 +01 ON

+01 –02 OFF

+04 +01 OFF

+02 00 ON

+02 +03 OFF

(super bass)

Indication, [Range]

S.BS*2 (super bass), [S.BS ON or S.BS OFF]

[01 to 05] Maintain the richness and fullness of the bass sound regardless of how low you set the volume.

SUB. W

Adjust the subwoofer output level when a subwoofer is connected.

VOL (volume), [00 to 30 or 50* Adjust the volume.

(subwoofer), [00 to 08]

When you adjust the bass, treble, or

super bass the adjustment you have made is stored for the currently selected sound mode (C-EQ) including “USER.”

If you are using a two-speaker system, set the

fader level to “00.”

This adjustment cannot affect the subwoofer

output.

Range adjustment for super bass is adjustable

only when it is set to “S.BS ON.”

Depending on the amplifier gain control

setting. (See page 10 for details.)

]

ENGLISH

Adjusting the sound

You can adjust the sound characteristics to your preference.

*1 Displayed only when “L/O MODE” is set to

“WOOFER” (see page 10).

Indication, [Range]

BAS*2 (bass), [–06 to +06]

Adjust the bass.

TRE*

(treble), [–06 to +06]

Adjust the treble.

FAD*3 (fader), [R06 to F06]

Adjust the front and rear speaker balance.

BAL*

(balance), [L06 to R06]

Adjust the left and right speaker balance.

General settings — PSM

You can change PSM (Preferred Setting Mode) items listed in the table on page 10.

2 Select a PSM item.

3 Adjust the PSM item selected.

4 Repeat steps 2 and 3 to adjust other

PSM items if necessary. Then press SEL to finish the procedure.

To be continued...

Page 10

Indications Selectable settings, [reference page]

DEMO

Display

demonstration

CLOCK H

ENGLISH

Hour adjustment

CLOCK M

Minute adjustment

L/O MODE

Line output mode

AMP GAIN

Amplifier gain

control

AREA

Tuner channel

interval

DEMO ON : [Initial]; Display demonstration will be activated automatically

if no operation is done for about 20 seconds, [6].

DEMO OFF : Cancels.

1 – 12, [6]

[Initial: 1 (1:00)]

00 – 59, [6]

[Initial: 00 (1:00)]

When connecting an amplifier or a subwoofer, set this correctly. REAR : [Initial]; Select if the REAR LINE OUT terminals are used for

connecting the speakers through an external amplifier.

WOOFER : Select if the REAR LINE OUT terminals are used for

connecting a subwoofer.

You can change the maximum volume level of this unit. LOW PWR : VOL 00 – VOL 30 (Select this if the maximum power of the

speaker is less than 45 W to avoid damaging the speaker.)

HIGH PWR : [Initial]; VOL 00 – VOL 50

AREA US : [Initial]; Select this when using the unit in North or South

America, except Middle South America. (FM: 200 kHz; AM: 10 kHz)

AREA EU : Select this when using the unit in any other area than North,

Middle South and South America. (FM: 50 kHz—manual tuning, 100 kHz—auto search; AM: 9 kHz)

AREA SA : Select this when using the unit in Middle South America.

(FM: 100 kHz; AM: 10 kHz)

Maintenance

How to clean the connectors

Frequent detachment will deteriorate the connectors. To minimize this possibility, periodically wipe the connectors with a cotton swab or cloth moistened with alcohol, being careful not to damage the connectors.

Moisture condensation

Moisture may condense on the lens inside the CD player in the following cases:

• After starting the heater in the car.

• If it becomes very humid inside the car.

Connector

Should this occur, the CD player may malfunction.In this case, eject the disc and leave the unit turned on for a few hours until the moisture evaporates.

How to handle discs

When removing a disc from its case, press down the center

holder of the case and lift the disc out, holding it by the edges.

• Always hold the disc by the edges. Do not touch its recording surface.

When storing a disc into its case, gently insert the disc around the center holder (with the printed surface facing up).

• Make sure to store discs into the cases after use.

Center holder

Page 11

To keep discs clean

A dirty disc may not play correctly. If a disc does become dirty, wipe it with a soft cloth in a straight line from center to edge.

• Do not use any solvent (for example, conventional record cleaner, spray, thinner, benzine, etc.) to clean discs.

Do not use the following discs:

Warped disc

Sticker

More about this unit

To play new discs

New discs may have some rough spots around the inner and outer edges. If such a disc is used, this unit may reject the disc. To remove these rough spots, rub the edges with a pencil or ball-point pen, etc.

Sticker residue

Disc

Stick-on label

ENGLISH

Basic operations

Turning on the power

• By pressing SOURCE on the unit, you can also turn on the power. If the source is ready, playback also starts.

Turning off the power

• If you turn off the power while listening to a disc, disc play will start from where playback has been stopped previously, next time you turn on the power.

Selecting the sources

• When no disc is loaded in the unit, “DISC” cannot be selected.

Tuner operations

Storing stations in memory

• During SSM search...

– All previously stored stations are erased and

stations are stored newly.

–

Received stations are preset in No. 1 (lowest frequency) to No. 6 (highest frequency).

– When SSM is over, the station stored in

No. 1 will be automatically tuned in.

• When storing a station manually, a previously preset station is erased when a new station is stored in the same preset number.

Disc operations

Caution for DualDisc playback

• The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the use of NonDVD side of a DualDisc on this product may not be recommended.

General

• This unit has been designed to reproduce CDs, and CD-Rs (Recordable)/CD-RWs (Rewritable) in audio CD (CD-DA) format.

• When a disc has been loaded, selecting “DISC” for the playback source starts disc play.

Inserting a disc

• When a disc is inserted upside down, the disc automatically ejects.

• Do not insert 8 cm discs (single CD) and unusual shape discs (heart, flower, etc.) into the loading slot.

Playing a CD-R or CD-RW

• Use only “finalized” CD-Rs or CD-RWs.

• This unit can play back multi-session discs; however, unclosed sessions will be skipped while playing.

• Some CD-Rs or CD-RWs may not play back on this unit because of their disc characteristics, and for the following causes:

To be continued...

Page 12

– Discs are dirty or scratched. – Moisture condensation occurs on the lens

inside the unit. – The pickup lens inside the unit is dirty. – CD-R/CD-RW on which the files are

written with “Packet Write” method.

ENGLISH

– There are improper recording conditions

(missing data, etc.) or media conditions

(stain, scratch, warp, etc.).

• CD-RWs may require a longer readout time

since the reflectance of CD-RWs is lower than that of regular CDs.

• Do not use the following CD-Rs or CD-RWs: – Discs with stickers, labels, or protective seal

stuck to the surface. – Discs on which labels can be directly

printed by an ink jet printer. Using these discs under high temperatures

or high humidity may cause malfunctions or damages to the unit.

Changing the source

• If you change the source, playback also stops (without ejecting the disc).

Next time you select “DISC” for the playback

source, disc play starts from where it has been stopped previously.

Ejecting a disc

• If the ejected disc is not removed within 15 seconds, the disc is automatically inserted again into the loading slot to protect it from dust. (Disc will not play this time.)

General settings—PSM

• If you change the “AMP GAIN” setting from “HIGH PWR” to “LOW PWR” while the volume level is set higher than “VOL 30,” the unit automatically changes the volume level to “VOL 30.”

Troubleshooting

What appears to be trouble is not always serious. Check the following points before calling a service center.

Symptoms Remedies/Causes

• Sound cannot be heard from the speakers.

General

• This unit does not work at all. Reset the unit (see page 2).

• SSM automatic presetting does not work.

• Static noise while listening to the

FM/AM

radio.

• Disc automatically ejects. Insert the disc correctly.

• CD-R/CD-RW cannot be played back.

• Tracks on the CD-R/CD-RW cannot be skipped.

• Disc can be neither played back nor ejected.

Disc playback

• Disc sound is sometimes interrupted. • Stop playback while driving on rough roads.

• “NO DISC” appears on the display. Insert a playable disc into the loading slot.

• Adjust the volume to the optimum level.

• Check the cords and connections.

Store stations manually.

Connect the antenna firmly.

• Insert a finalized CD-R/CD-RW.

•

Finalize the CD-R/CD-RW with the component which you used for recording.

• Unlock the disc (see page 8).

• Eject the disc forcibly (see page 2).

• Change the disc.

• Check the cords and connections.

Page 13

Specifications

AUDIO AMPLIFIER SECTION

Power Output:

17 W RMS × 4 Channels at 4 Ω

and ≤ 1% THD+N

Signal to Noise Ratio:

80 dBA (reference: 1 W into 4 Ω)

Load Impedance: 4 Ω (4 Ω to 8 Ω allowance) Tone Control Range: Bass: ±10 dB at 100 Hz Treble: ±10 dB at 10 kHz Frequency Response: 40 Hz to 20 000 Hz Line-Out Level/Impedance:

2.0 V/20 kΩ load (full scale) Output Impedance: 1 kΩ Subwoofer-Out Level/Impedance:

2.0 V/20 kΩ load (full scale)

TUNER SECTION

Frequency Range: FM: 87.5 MHz to 107.9 MHz (with channel interval set to 100 kHz

or 200 kHz)

87.5 MHz to 108.0 MHz (with channel interval set to 50 kHz) AM: 530 kHz to 1 710 kHz (with channel interval set to 10 kHz) 531 kHz to 1 602 kHz (with channel interval set to 9 kHz)

[FM Tuner]

Usable Sensitivity: 11.3 dBf (1.0 μV/75 Ω) 50 dB Quieting Sensitivity:

16.3 dBf (1.8 μV/75 Ω) Alternate Channel Selectivity (400 kHz): 65 dB Frequency Response: 40 Hz to 15 000 Hz Stereo Separation: 35 dB Capture Ratio: 1.5 dB

[AM Tuner]

Sensitivity: 20 μV Selectivity: 35 dB

CD PLAYER SECTION

Type: Compact disc player Signal Detection System: Non-contact optical pickup (semiconductor laser) Number of channels: 2 channels (stereo) Frequency Response: 5 Hz to 20 000 Hz Dynamic Range: 96 dB Signal-to-Noise Ratio: 98 dB Wow and Flutter: Less than measurable limit

GENERAL

Power Requirement: Operating Voltage:

DC 14.4 V (11 V to 16 V allowance) Grounding System: Negative ground Allowable Operating Temperature: 0°C to +40°C (32°F to 104°F) Dimensions (W × H × D): Installation Size (approx.): 182 mm × 52 mm × 150 mm (7-3/16” × 2-1/16” × 5-15/16”) Panel Size (approx.): 188 mm × 58 mm × 11 mm (7-7/16” × 2-5/16” × 7/16”) Mass (approx.):

1.2 kg (2.6 lbs) (excluding accessories)

Design and specifications are subject to change without notice.

If a kit is necessary for your car, consult your telephone directory for the nearest car audio speciality shop.

ENGLISH

Page 14

Having TROUBLE with operation?

Please reset your unit

Refer to page of How to reset your unit

Still having trouble??

USA ONLY

Call 1-800-252-5722

http://www.jvc.com

We can help you!

EN, SP, FR

1005DTSMDTJEIN

Page 15

GET0330-002A

[J]

KD-G120R/KD-G120

Installation/Connection Manual Manual de instalación/conexión Manuel d’installation/raccordement

1005DTSMDTJEIN EN, SP, FR

ENGLISH

This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does not have this system, a

voltage inverter is required, which can be purchased at JVC car audio dealers.

WARNINGS

To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the unit.

• Be sure to ground this unit to the car’s chassis again after

installation.

Notes:

• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio dealer.

• It is recommended to connect to the speakers with maximum power of more than 45 W (both at the rear and at the front, with

an impedance of 45 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page 10 of the INSTRUCTIONS).

• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.

• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.

4 Ω to 8 Ω). If the maximum power is less than

ESPAÑOL

Esta unidad está diseñada para funcionar con 12 V de CC, con sistemas eléctricos de masa NEGATIVA. Si su vehículo no posee

este sistema, será necesario un inversor de tensión, que puede ser adquirido en los concesionarios de JVC de equipos de audio para automóviles.

ADVERTENCIAS

Para evitar cortocircuitos, recomendamos que desconecte el terminal negativo de la batería y que efectúe todas las conexiones eléctricas antes de instalar la unidad.

• Asegúrese de volver a conectar a masa esta unidad al chasis del automóvil después de la instalación.

Notas:

• Reemplace el fusible por uno con la corriente especificada. Si el fusible se quemase frecuentemente consulte con su concesionario de JVC de equipos de audio para automóviles.

• Se recomienda conectar los altavoces con una potencia máxima de más de 45 W (tanto atrás como adelante, con una impedancia de

4 Ω a 8 Ω). Si la potencia máxima es de menos de 45 W, cambie

“AMP GAIN” para evitar daños en los altavoces (consulte la página 10 del MANUAL DE INSTRUCCIONES).

• Para evitar cortocircuitos, cubra los cables NO UTILIZADOS con cinta aislante.

• El sumidero térmico estará muy caliente después del uso. Asegúrese de no tocarlo al desmontar esta unidad.

FRANÇAIS

Cet appareil est conçu pour fonctionner sur des sources de courant continu de 12 V à masse NEGATIVE. Si votre véhicule n’offre pas ce type d’alimentation, il vous faut un convertisseur de tension, que vous pouvez acheter chez un revendeur d’autoradios JVC.

AVERTISSEMENTS

Pour éviter tout court-circuit, nous vous recommandons de débrancher la borne négative de la batterie et d’effectuer tous les raccordements électriques avant d’installer l’appareil.

• Assurez-vous de raccorder de nouveau la mise à la masse de cet appareil au châssis de la voiture après l’installation.

Remarques:

• Remplacer le fusible par un de la valeur précisée. Si le fusible saute souvent, consulter votre revendeur d’autoradios JVC.

• Il est recommandé de connecter des enceintes avec une puissance de plus de 45 W (les enceintes arrière et les enceintes avant, avec une

impédance comprise entre inférieure à 45 W, changez “AMP GAIN” pour éviter d’endommager vos enceintes (voir page 10 du MANUEL D’INSTRUCTIONS).

• Pour éviter les court-circuits, couvrir les bornes des fils qui ne sont PAS UTILISÉS avec de la bande isolante.

• Le dissipateur de chaleur devient très chaud après usage. Faire attention de ne pas le toucher en retirant cet appareil.

4 Ω et 8 Ω). Si la puissance maximum est

Heat sink

Sumidero térmico

Dissipateur de chaleur

PRECAUTIONS on power supply and speaker connections:

• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be seriously damaged.

• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your car.

PRECAUCIONES sobre las conexiones de la fuente de alimentación y de los altavoces:

• NO conecte los conductores de altavoz del cable de alimentación a la batería de automóvil, pues podrían producirse graves daños en la unidad.

• ANTES de conectar a los altavoces los conductores de altavoz del cable de alimentación, verifique el conexionado de altavoz de su automóvil.

PRECAUTIONS sur l’alimentation et la connexion des enceintes:

• NE CONNECTEZ PAS les fils d’enceintes du cordon d’alimentation à la batterie; sinon, l’appareil serait sérieusement endommagé.

• AVANT de connecter les fils d’enceintes du cordon d’alimentation aux enceintes, vérifiez le câblage des enceintes de votre voiture.

Parts list for installation and connection

The following parts are provided for this unit. After checking them, please set them correctly.

A / B Hard case/Control panel

Estuche duro/Panel de control

Etui de transport/Panneau de commande

Power cord

Cordón de alimentación

Cordon d’alimentation

Lista de piezas para instalación y conexión

Con esta unidad se suministran las siguientes piezas. Después de inspeccionarlas, colóquelas correctamente.

Sleeve

Cubierta

Manchon

Washer (ø5)

Arandela (ø5)

Rondelle (ø5)

Lock nut (M5)

Tuerca de seguridad (M5)

Ecrou d’arrêt (M5)

Only for KD-G120R / Sólo para KD-G120R / Seulement pour le KD-G120R

Liste des pièces pour l’installation et raccordement

Les pièces suivantes sont fournies avec cet appareil. Après vérification, veuillez les placer correctement.

Trim plate

Placa de guarnición

Plaque d’assemblage

Mounting bolt—M5 × 20 mm (M5 × 13/16")

Perno de montaje—M5 × 20 mm (M5 × 13/16 pulgada)

Boulon de montage—M5 × 20 mm (M5 × 13/16 pouces)

Rubber cushion

Cojín de goma

Amortisseur en caoutchouc

Handles

Manijas

Poignées

Remote controller

Control remoto

Télécommade

Battery

Pila

Pile

Page 16

INSTALLATION

INSTALACION (MONTAJE EN EL

INSTALLATION (MONTAGE

(IN-DASH MOUNTING)

The following illustration shows a typical installation. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying kits.

• If you are not sure how to install this unit correctly, have it installed by a qualified technician.

TABLERO DE INSTRUMENTOS)

La siguiente ilustración muestra una instalación típica. Si tiene alguna pregunta o necesita información acerca de las herramientas para instalación, consulte con su concesionario de JVC de equipos de audio para automóviles o a una compañía que suministra tales herramientas.

• Si usted no está seguro de cómo instalar correctamente la unidad, hágala instalar por un técnico cualificado.

Do the required electrical connections.

Realice las conexiones eléctricas requeridas.

Réalisez les connexions électriques.

DANS LE TABLEAU DE BORD)

L’illustration suivante est un exemple d’installation typique. Si vous avez des questions ou avez besoin d’information sur des kits d’installation, consulter votre revendeur d’autoradios JVC ou une compagnie d’approvisionnement.

• Si l’on n’est pas sûr de pouvoir installer correctement cet appareil, le faire installer par un technicien qualifié.

When you stand the unit, be careful not to damage the fuse on the rear.

Al poner la unidad vertical, tenga cuidado de no dañar el fusible provisto en la parte posterior.

Lorsque vous mettez l’appareil à la verticale, faire attention de ne pas endommager le fusible situé sur

l’arrière.

Removing the unit

Before removing the unit, release the rear section.

Extracción de la unidad

Antes de extraer la unidad, libere la sección trasera.

Bend the appropriate tabs to hold the sleeve firmly in place.

Doble las lengüetas apropiadas para retener firmemente la manga en su lugar.

Tordez les languettes appropriées pour maintenir le manchon en place.

Retrait de l’appareil

Avant de retirer l’appareil, libérer la section arrière.

Insert the two handles, then pull them as illustrated so that the unit can be removed.

Inserte las dos manijas y, a continuación, extráigalas de la manera indicada en la ilustración para poder desmontar la unidad.

Insérez les deux poignées, puis tirez de la façon illustrée de façon à retirer l’appareil.

When using the optional stay / Cuando emplea un soporte opcional / Lors de l’utilisation du hauban en option

Stay (option)

Soporte (opción)

Hauban (en option)

Fire wall

Tabique a prueba de incendios

Cloison

Dashboard

Tablero de instrumentos

Tableau de bord

Screw (option)

Tornillo (opción)

Vis (en option)

When installing the unit without using the sleeve / Instalación de la unidad sin utilizar la cubierta / Lors de l’installation de l’appareil scans utiliser de manchon

In a Toyota car for example, first remove the car radio and install the unit in its place.

En un automóvil Toyota, por ejemplo, en primer lugar desmonte el autorradio e instale la unidad en su lugar.

Dans une voiture Toyota, par exemple, retirez d’abord l’autoradio et installez l’appareil à sa place.

Flat type screws—M5 × 8 mm (M5 × 3/8")*

Tornillos tipo plano—M5 × 8 mm(M5 × 3/8 pulgada)*

Vis à tête plate—M5 × 8 mm (M5 × 3/8 pouces)*

Bracket*

Ménsula*

Support *

Pocket

Compartimiento

Poche

Flat type screws—M5 × 8 mm (M5 × 3/8")*

Tornillos tipo plano—M5 × 8 mm (M5 × 3/8 pulgada)*

Vis à tête plate—M5 × 8 mm (M5 × 3/8 pouces)*

Bracket*

Ménsula*

Support *

* Not supplied for this unit. * No suministrado con esta unidad. * Non fourni avec cet appareil.

Install the unit at an angle of less than 30˚.

Instale la unidad a un ángulo de menos de 30˚.

Installez l’appareil avec un angle de moins de 30˚.

Note : When installing the unit on the mounting bracket, make sure to use the 8 mm (3/8") -long screws. If longer

screws are used, they could damage the unit.

Nota : Cuando instala la unidad en la ménsula de montaje, asegúrese de utilizar los tornillos de 8 mm (3/8 pulgada) de

longitud. Si se utilizan tornillos más largos, éstos pueden dañar la unidad.

Remarque : Lors de l’installation de l’appareil sur le support de montage, s’assurer d’utiliser des vis d’une longueur de 8 mm

(3/8 pouces). Si des vis plus longues sont utilisées, elles peuvent endommager l’appareil.

Page 17

ENGLISH

ESPAÑOL FRANÇAIS

ELECTRICAL CONNECTIONS CONEXIONES ELECTRICAS RACCORDEMENTS ELECTRIQUES

Typical connections / Conexiones tipicas / Raccordements typiques

Before connecting: Check the wiring in the vehicle carefully.

Incorrect connection may cause serious damage to this unit. The leads of the power cord and those of the connector from the car body may be different in color.

1 Connect the colored leads of the power cord in the order

specified in the illustration below.

2 Connect the antenna cord.

3 Finally connect the wiring harness to the unit.

Rear ground terminal

Terminal de tierra posterior

Borne arrière de masse

Antenna terminal

Terminal de la antena

Borne de l’antenne

Line out (see diagram )

Salida de línea (véase diagrama )

Sortie de ligne (voir le diagramme )

Antes de la conexión: Verifique atentamente el conexionado del

vehículo. Una conexión incorrecta podría producir daños graves en la unidad. Los cordones del cable de alimentación y los del conector procedentes de la carrocería del automóvil podrían ser de diferentes en color.

1 Conecte los conductores de color del cable de alimentación en el

orden especificado en la ilustración de abajo.

2 Conecte el cable de antena.

3 Por último, conecte el cable de alimentación a la unidad.

15 A fuse

Fusible de 15 A

Fusible 15 A

Avant de commencer la connexion: Vérifiez attentivement

le câblage du véhicule. Une connexion incorrecte peut endommager sérieusement l’appareil. Le fil du cordon d’alimentation et ceux des connecteurs du châssis de la voiture peuvent être différents en couleur.

1 Connectez les fils colorés du cordon d’alimentation dans l’ordre

spécifié sur l’illustration ci-dessous.

2 Connectez le cordon d’antenne.

3 Finalement, connectez le faisceau de fils à l’appareil.

Before checking the operation of this unit prior to installation, this lead must be connected, otherwise power cannot be turned on.

Antes de comprobar el funcionamiento de esta unidad previa a de la instalación, es necesario conectar este cable, de lo contrario no se podrá conectar la alimentación.

Pour vérifier le fonctionnement de cet appareil avant installation, ce fil doit être raccordé, sinon l’appareil ne peut pas être mis sous tension.

Black

Negro

Noir

Yellow

Amarillo*

Jaune*

Red

Rojo

Rouge

Blue with white stripe

Azul con rayas blancas

Bleu avec bande blanche

Not supplied for this unit

No suministrado con esta unidad

Non fourni avec cet appareil

To metallic body or chassis of the car

A un cuerpo metálico o chasis del automóvil

Vers corps métallique ou châssis de la voiture

To a live terminal in the fuse block connecting to the car battery (bypassing the ignition switch) (constant 12 V)

A un terminal activo del bloque de fusibles conectado a la batería del automóvil (desviando el interruptor de encendido) (12 V constantes)

A une borne sous tension du porte-fusible connectée à la batterie de la voiture (en dérivant l’interrupteur d’allumage) (12 V constant)

To an accessory terminal in the fuse block

A un terminal accesorio del bloque de fusibles

Vers borne accessoire du porte-fusible

To the remote lead of other equipment or automatic antenna if any (200 mA max.)

Al conductor remoto de otro equipo o de la antena automática, si hubiere (máx. 200 mA)

Au fil de télécommande de l’autre appareil ou à l’antenne automatique s’il y en a une (200 mA max.)

Ignition switch

Interruptor de encendido

Interrupteur d’allumage

Fuse block

Bloque de fusibles

Porte-fusible

White with black stripe

Blanco con rayas negras

Blanc avec bande noire

White

Blanco

Blanc

Left speaker (front)

Altavoz izquierdo (delantero)

Enceinte gauche (avant)

Gray with black stripe

Gris con rayas negras

Gris avec bande noire

Gray

Gris

Right speaker (front)

Altavoz derecho (delantero)

Enceinte droit (avant)

Green with black stripe

Verde con rayas negras

Vert avec bande noire

Green

Verde

Vert

Left speaker (rear)

Altavoz izquierdo (trasero)

Enceinte gauche (arrière)

Purple with black stripe

Púrpura con rayas negras

Violet avec bande noire

Purple

Púrpura

Violet

Right speaker (rear)

Altavoz derecho (trasero)

Enceinte droit (arrière)

Page 18

Connecting the external amplifier or subwoofer / Conexión del ampliﬁ cador o subwoofer exterior / Connexion d’un amplificateur extérieur

ou d’un caisson de grave

You can connect an amplifier to upgrade your car stereo system.

• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this unit.

• Disconnect the speakers from this unit, connect them to the

amplifier. Leave the speaker leads of this unit unused.

Usted podrá conectar un amplificador para mejorar el sistema estéreo de su automóvil.

• Conecte el conductor remoto (azul con rayas blancas) al conductor remoto del otro equipo para poderlo controlar a través de esta unidad.

• Desconecte los altavoces de esta unidad y conéctelos al amplificador. Los cables de los altavoces de esta unidad quedan sin usar.

Vous pouvez connecter un amplificateur pour améliorer votre système autoradio.

• Connectez le fil de commande à distance (bleu avec bande blanche)

au fil de commande à distance de l’autre appareil de façon qu’il puisse être commandé via cet appareil.

• Déconnectez les enceintes de cet appareil et connectez-les à l’amplificateur. Laissez les fils d’enceintes de cet appareil inutilisés.

Set “L/O MODE” to “REAR” (See page 10 of the INSTRUCTIONS.) Ajuste “L/O MODE” a “REAR” (Consulte la página 10 del MANUAL DE INSTRUCCIONES.) Réglez “L/O MODE” sur “REAR” (Voir la page 10 du MANUEL D’INSTRUCTIONS.)

You can connect a power amplifier for rear speakers.

Puede conectar un amplificador de potencia para los altavoces traseros.

Vous pouvez connecter un amplificateur de puissance pour les enceintes arrière.

JVC Amplifier

Amplificador de JVC

JVC Amplificateur

Remote lead

Cable remoto

Fil d’alimentation à distance

Remote lead (Blue with white stripe)

Cable remoto (Azul con rayas blancas)

Fil d’alimentation à distance (Bleu avec bande blanche)

Y-connector (not supplied for this unit)

Conector en Y (no suministrado con esta unidad)

Connecteur Y (non fourni avec cet appareil)

To the remote lead of other equipment or automatic antenna if any

Al conductor remoto de otro equipo o de la antena automática, si hubiere

Au fil de télécommande de l’autre appareil ou à l’antenne automatique s’il y en a une

Rear speakers

Altavoces posteriores

Enceintes arrière

Set “L/O MODE” to “WOOFER” (See page 10 of the INSTRUCTIONS.) Ajuste “L/O MODE” a “WOOFER” (Consulte la página 10 del MANUAL DE INSTRUCCIONES.) Réglez “L/O MODE” sur “WOOFER” (Voir la page 10 du MANUEL D’INSTRUCTIONS.)

You can also connect a subwoofer to the REAR LINE OUT terminals.

También puede conectar un subwoofer para los terminales REAR LINE OUT.

Vous pouvez aussi connecter un caisson de grave aux prises REAR LINE OUT.

JVC Amplifier

Amplificador de JVC

JVC Amplificateur

Subwoofer

Caisson de grave

Firmly attach the ground wire to the metallic body or to the chassis of

the car—to the place uncoated with paint (if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the unit.

Signal cord (not supplied for this unit)

Fije firmemente el cable de tierra a la carrocería metálica o al chasis—a un

lugar no cubierto con pintura (si está cubierto con pintura, quítela antes de fijar el cable). De lo contrario, se podrían producir daños en la unidad.

Cable de señal (no suministrado con esta unidad)

Front speakers

Altavoces delanteros

Enceintes avant

Attachez solidement le fil de mise à la masse au châssis métallique de la

voiture—à un endroit qui n’est pas recouvert de peinture (s’il est recouvert de peinture, enlevez d’abord la peinture avant d’attacher le fil). L’appareil peut être endommagé si cela n’est pas fait correctement.

Cordon de signal (non fourni avec cet appareil)

TROUBLESHOOTING

• The fuse blows. * Are the red and black leads connected correctly?

• Power cannot be turned on. * Is the yellow lead connected?

• No sound from the speakers. * Is the speaker output lead short-circuited?

• Sound is distorted.

* Is the speaker output lead grounded? * Are the “–” terminals of L and R speakers grounded in common?

• Noise interfere with sounds. * Is the rear ground terminal connected to the car’s chassis using

shorter and thicker cords?

• This unit becomes hot.

* Is the speaker output lead grounded? * Are the “–” terminals of L and R speakers grounded in common?

• This unit does not work at all. * Have you reset your unit?

LOCALIZACION DE AVERIAS

• El fusible se quema.

* ¿Están los conductores rojo y negro correctamente conectados?

• No es posible conectar la alimentación.

* ¿Está el cable amarillo conectado?

• No sale sonido de los altavoces.

¿Está el cable de salida del altavoz cortocircuitado?

• El sonido presenta distorsión.

* ¿Está el cable de salida del altavoz conectado a masa? * ¿Están los terminales “–” de los altavoces L y R conectados a una

masa común?

• Perturbación de ruido.

* ¿El terminal de tierra trasero está conectado al chasis del automóvil

utilizando los cordones más corto y más grueso?

• La unidad se calienta.

* ¿Está el cable de salida del altavoz conectado a masa? * ¿Están los terminales “–” de los altavoces L y R conectados a una

masa común?

• Este receptor no funciona en absoluto.

* ¿Reinicializó el receptor?

EN CAS DE DIFFICULTES

• Le fusible saute.

* Les fils rouge et noir sont-ils racordés correctement?

• L’appareil ne peut pas être mise sous tension.

* Le fil jaune est-elle raccordée?

• Pas de son des enceintes.

* Le fil de sortie d’enceinte est-il court-circuité?

• Le son est déformé.

* Le fil de sortie d’enceinte est-il à la masse? * Les bornes “–” des enceintes gauche et droit sont-elles mises ensemble

à la masse?

• Interférence avec les sons.

* La prise arrière de mise à la terre est-elle connectée au châssis de la

voiture avec un cordon court et épais?

• L’appareil devient chaud.

* Le fil de sortie d’enceinte est-il à la masse? * Les bornes “–” des enceintes gauche et droit sont-elles mises ensemble

à la masse?

• Cet appareil ne fonctionne pas du tout.

* Avez-vous réinitialisé votre appareil?

Page 19

CD RECEIVER

KD-G124/KD-G123

For canceling the display demonstration, see page 5.

KD-G124

KD-G123

For installation and connections, refer to the separate manual.

INSTRUCTIONS

GET0332-001A

[UI]

Page 20

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and to

obtain the best possible performance from the unit.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel.

3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

Warning:

If you need to operate the unit while driving, be sure to look ahead carefully or you may be involved in a traffic accident.

How to reset your unit

• Your preset adjustments will also be erased.

• If a disc is loaded, it will eject. Be careful not to

drop the disc.

How to forcibly eject a disc

• If this does not work, reset your unit.

• Be careful not to drop the disc when it ejects.

Caution on volume setting:

Discs produce very little noise compared with other sources. Lower the volume before playing a disc to avoid damaging the speakers by the sudden increase of the output level.

How to use the M MODE button

If you press M MODE, the unit goes into functions mode, then the number buttons work as different function buttons.

Ex.: When number button 2 works as

MO (monaural) button.

Time countdown indicator

To use these buttons for their original functions again after pressing M MODE, wait

for 5 seconds without pressing any of these buttons until the functions mode is cleared or press M MODE again.

Page 21

How to read this manual

• Button operations are mainly explained with the illustrations in the table below.

•

is used to indicate an indicator is

displayed for the corresponding operation.

• Some related tips and notes are explained in “More about this unit” (see pages 11 and 12).

Press briefly.

Press repeatedly.

Press either one.

Press and hold until your desired response begins.

Press and hold both buttons at the same time.

How to detach/attach the control

panel

Control panel — KD-G124 and KD-G123 ........ 4

Getting started ................................. 5

Basic operations .................................................... 5

Radio operations .............................. 6

Disc operations ................................. 7

Playing a disc in the unit ....................................... 7

Sound adjustments ........................... 8

General settings — PSM ................... 9

Maintenance .................................... 10

More about this unit ......................... 11

Troubleshooting ............................... 12

Specifications ................................... 13

Detaching...

Attaching...

For safety...

• Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.

• Stop the car before performing any complicated operations.

Temperature inside the car...

If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes normal before operating the unit.

Page 22

Control panel — KD-G124 and KD-G123

Parts identification

Display window

1 (standby/on/attenuator) button 2 SOURCE button 3 BAND button 4 Loading slot 5 Display window 6 0 (eject) button 7 EQ (equalizer) button 8

¢/4 buttons

9 Control dial p SEL (select) button q DISP (display) button w MO (monaural) button e SSM (Strong-station Sequential Memory)

button

r Number buttons t RPT (repeat) button y RND (random) button u M MODE button i

(control panel release) button

Display window

o DISC indicator ; RND a RPT (repeat) indicator s S. BASS (super bass) indicator d EQ (equalizer) indicator f Sound mode (C-EQ: custom equalizer)

indicators—JAZZ, CLASSIC, HIP HOP, POPS, ROCK, USER

g Source display Volume level indicator Time countdown indicator

h Main display j Tuner reception indicators—ST (stereo),

MO (monaural)

(disc random) indicator

Page 23

Getting started

Basic operations

~ Turn on the power.

Basic settings

• See also “General settings — PSM” on page 9.

* You cannot select “DISC” as the

playback source if there is no disc in the loading slot.

1 Canceling the display

2 Setting the clock

! For FM/AM tuner

⁄ Adjust the volume.

Volume level indicator

Volume level appears.

@ Adjust the sound as you want. (See

page 8.)

To drop the volume in a moment (ATT)

To restore the sound, press it again.

To turn off the power

3 Finish the procedure.

To check the current clock time while the power is turned off

To check the other information while listening to the radio/a disc

Frequency/Elapsed playing time Ô Clock

demonstrations

Select “DEMO,” then “DEMO OFF.”

Select “CLOCK H” (hour), then adjust the hour. Select “CLOCK M” (minute), then adjust the minute.

Page 24

Radio operations

When an FM stereo broadcast is hard to receive

Lights up when monaural mode is activated.

Lights up when receiving an FM stereo broadcast with sufficient signal strength.

Selected band appears.

! Start searching for a station.

When a station is received, searching stops. To stop searching, press the same button again.

To tune in to a station manually

In step ! above... 1

2 Select the desired station frequencies.

Reception improves, but stereo effect will be lost. To restore the stereo effect, repeat the same procedure “MONO OFF” appears and the MO indicator goes off.

Storing stations in memory

You can preset six stations for each band.

FM station automatic presetting —

SSM (Strong-station Sequential Memory)

1 Select the FM band (FM1 – FM3) you

want to store into.

“SSM” flashes, then disappears when automatic presetting is over.

Local FM stations with the strongest signals are searched and stored automatically in the FM band.

Page 25

Manual presetting

Ex.: Storing FM station of 92.5 MHz into preset

number 4 of the FM1 band.

Preset number flashes for a while.

Listening to a preset station

Disc operations

Playing a disc in the unit

All tracks will be played repeatedly until you change the source or eject the disc.

To stop play and eject the disc

To fast-forward or reverse the track

To go to the next or previous tracks

To locate a particular track directly

To select a number from 01 – 06:

2 Select the preset station (1 – 6) you

want.

To select a number from 07 – 12:

Prohibiting disc ejection

You can lock a disc in the loading slot.

To cancel the prohibition, repeat the same procedure.

Page 26

Selecting the playback modes

You can use only one of the following playback modes at a time.

2 Select your desired playback mode.

Adjusting the sound

You can adjust the sound characteristics to your preference.

7 Repeat play

Mode Plays repeatedly

TRK RPT : The current track. RPT OFF : Cancels.

7 Random play

Mode Plays at random

DISC RND : All tracks of the current disc.

RND OFF : Cancels.

Sound adjustments

You can select a preset sound mode suitable to the music genre (C-EQ: custom equalizer).

Preset values

Indication (For)

USER (Flat sound)

ROCK

(Rock or disco music)

CLASSIC

(Classical music)

POPS (Light music)

HIP HOP

(Funk or rap music)

JAZZ (Jazz music)

BAS TRE S.BS

(bass) (treble)

00 00 OFF

+03 +01 ON

+01 –02 OFF

+04 +01 OFF

+02 00 ON

+02 +03 OFF

(super

bass)

Displayed only when “L/O MODE” is set to

“WOOFER” (see page 9).

Indication, [Range]

BAS*2 (bass), [–06 to +06]

Adjust the bass.

TRE*

(treble), [–06 to +06]

Adjust the treble.

FAD*

(fader), [R06 to F06]

Adjust the front and rear speaker balance.

BAL*

(balance), [L06 to R06]

Adjust the left and right speaker balance.

S.BS*2 (super bass), [S.BS ON or S.BS OFF]

[01 to 05] Maintain the richness and fullness of the bass sound regardless of how low you set the volume.

SUB. W

Adjust the subwoofer output level when a subwoofer is connected.

VOL (volume), [00 to 30 or 50* Adjust the volume.

(subwoofer), [00 to 08]

When you adjust the bass, treble, or

super bass the adjustment you have made is stored for the currently selected sound mode (C-EQ) including “USER.”

If you are using a two-speaker system, set the

fader level to “00.”

This adjustment cannot affect the subwoofer

output.

Range adjustment for super bass is adjustable

only when it is set to “S.BS ON.”

Depending on the amplifier gain control

setting. (See page 9 for details.)

]

Page 27

General settings — PSM

You can change PSM (Preferred Setting Mode) items listed in the table that follows.

3 Adjust the PSM item selected.

4 Repeat steps 2 and 3 to adjust other

2 Select a PSM item.

5 Finish the procedure.

Indications Selectable settings, [reference page]

DEMO

Display

demonstration

CLOCK H

Hour adjustment

CLOCK M

Minute adjustment

L/O MODE

Line output mode

AMP GAIN

Amplifier gain

control

DEMO ON : [Initial]; Display demonstration will be activated automatically

if no operation is done for about 20 seconds, [5].

DEMO OFF : Cancels.

1 – 12, [5]

[Initial: 1 (1:00)]

00 – 59, [5]

[Initial: 00 (1:00)]

When connecting an amplifier or a subwoofer, set this correctly. REAR : [Initial]; Select if the REAR LINE OUT terminals are used for

connecting the speakers through an external amplifier.

WOOFER : Select if the REAR LINE OUT terminals are used for

connecting a subwoofer.

You can change the maximum volume level of this unit. LOW PWR : VOL 00 – VOL 30 (Select this if the maximum power of the

speaker is less than 50 W to avoid damaging the speaker.)

HIGH PWR : [Initial]; VOL 00 – VOL 50

PSM items if necessary.

Page 28

Maintenance

How to clean the connectors

Connector

Moisture condensation

Moisture may condense on the lens inside the CD player in the following cases:

• After starting the heater in the car.

• If it becomes very humid inside the car. Should this occur, the CD player may malfunction. In this case, eject the disc and leave the unit turned on for a few hours until the moisture evaporates.

How to handle discs

When removing a disc from its case, press down the center

holder of the case and lift the disc out, holding it by the edges.

• Always hold the disc by the edges. Do not touch its recording surface.

When storing a disc into its case, gently insert the disc around the center holder (with the printed surface facing up).

• Make sure to store discs into the cases after use.

Center holder

To play new discs

To keep discs clean

A dirty disc may not play correctly. If a disc does become dirty, wipe it with a soft cloth in a straight line from center to edge.

• Do not use any solvent (for example, conventional record cleaner, spray, thinner, benzine, etc.) to clean discs.

Do not use the following discs:

Warped disc

Sticker

Disc

Sticker residue

Stick-on label

Page 29

More about this unit

Basic operations

Turning on the power

• By pressing SOURCE on the unit, you can also turn on the power. If the source is ready, playback also starts.

Turning off the power

• If you turn off the power while listening to a disc, disc play will start from where playback has been stopped previously, next time you turn on the power.

Selecting the sources

• When no disc is loaded in the unit, “DISC” cannot be selected.

Tuner operations

Storing stations in memory

• During SSM search...

– All previously stored stations are erased and

stations are stored newly.

–

Received stations are preset in No. 1 (lowest frequency) to No. 6 (highest frequency).

– When SSM is over, the station stored in

No. 1 will be automatically tuned in.

• When storing a station manually, a previously preset station is erased when a new station is stored in the same preset number.

Disc operations

Caution for DualDisc playback

• The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the use of NonDVD side of a DualDisc on this product may not be recommended.

General

• This unit has been designed to reproduce CDs, and CD-Rs (Recordable)/CD-RWs (Rewritable) in audio CD (CD-DA) format.

• When a disc has been loaded, selecting “DISC” for the playback source starts disc play.

Inserting a disc

• When a disc is inserted upside down, the disc automatically ejects.

• Do not insert 8 cm discs (single CD) and unusual shape discs (heart, flower, etc.) into the loading slot.

Playing a CD-R or CD-RW

• Use only “finalized” CD-Rs or CD-RWs.

• This unit can play back multi-session discs; however, unclosed sessions will be skipped while playing.

• Some CD-Rs or CD-RWs may not play back on this unit because of their disc characteristics, and for the following causes:

– Discs are dirty or scratched. – Moisture condensation occurs on the lens

inside the unit. – The pickup lens inside the unit is dirty. – CD-R/CD-RW on which the files are

written with “Packet Write” method. – There are improper recording conditions

(missing data, etc.) or media conditions

(stain, scratch, warp, etc.).

• CD-RWs may require a longer readout time

since the reflectance of CD-RWs is lower than that of regular CDs.

• Do not use the following CD-Rs or CD-RWs: – Discs with stickers, labels, or protective seal

stuck to the surface. – Discs on which labels can be directly

printed by an ink jet printer. Using these discs under high temperatures

or high humidity may cause malfunctions or damages to the unit.

Changing the source

• If you change the source, playback also stops

(without ejecting the disc).

Next time you select “DISC” for the playback

source, disc play starts from where it has been stopped previously.

To be continued...

Page 30

Ejecting a disc

• If the ejected disc is not removed within 15 seconds, the disc is automatically inserted again into the loading slot to protect it from dust. (Disc will not play this time.)

General settings—PSM

Troubleshooting

What appears to be trouble is not always serious. Check the following points before calling a service center.

Symptoms Remedies/Causes

• Sound cannot be heard from the speakers.

General

• This unit does not work at all. Reset the unit (see page 2).

• SSM automatic presetting does not work.

• Static noise while listening to the

FM/AM

radio.

• Disc automatically ejects. Insert the disc correctly.

• CD-R/CD-RW cannot be played back.

• Tracks on the CD-R/CD-RW cannot be skipped.

• Disc can be neither played back nor ejected.

Disc playback

• Disc sound is sometimes interrupted. • Stop playback while driving on rough roads.

• “NO DISC” appears on the display. Insert a playable disc into the loading slot.

• Adjust the volume to the optimum level.

• Check the cords and connections.

Store stations manually.

Connect the antenna firmly.

• Insert a finalized CD-R/CD-RW.

•

Finalize the CD-R/CD-RW with the component which you used for recording.

• Unlock the disc (see page 7).

• Eject the disc forcibly (see page 2).

• Change the disc.

• Check the cords and connections.

Page 31

Specifications

AUDIO AMPLIFIER SECTION

Maximum Power Output: Front: 50 W per channel Rear: 50 W per channel Continuous Power Output (RMS): Front: 19 W per channel into 4 Ω, 40 Hz

to 20 000 Hz at no more than 0.8% total harmonic distortion.

Rear: 19 W per channel into 4 Ω, 40 Hz

to 20 000 Hz at no more than 0.8%

total harmonic distortion. Load Impedance: 4 Ω (4 Ω to 8 Ω allowance) Tone Control Range: Bass: ±10 dB at 100 Hz Treble: ±10 dB at 10 kHz Frequency Response: 40 Hz to 20 000 Hz Signal to Noise Ratio: 70 dB Line-Out Level/Impedance:

2.0 V/20 kΩ load (full scale) Output Impedance: 1 kΩ Subwoofer-Out Level/Impedance:

2.0 V/20 kΩ load (full scale)

TUNER SECTION

Frequency Range: FM: 87.5 MHz to 108.0 MHz AM: 531 kHz to 1 602 kHz

CD PLAYER SECTION

GENERAL

Power Requirement: Operating Voltage:

DC 14.4 V (11 V to 16 V allowance) Grounding System: Negative ground Allowable Operating Temperature: 0°C to +40°C Dimensions (W × H × D): Installation Size (approx.): 182 mm × 52 mm × 150 mm Panel Size (approx.): 188 mm × 58 mm × 11 mm Mass (approx.):

1.2 kg (excluding accessories)

Design and specifications are subject to change without notice.

[FM Tuner]

Usable Sensitivity: 11.3 dBf (1.0 μV/75 Ω) 50 dB Quieting Sensitivity:

16.3 dBf (1.8 μV/75 Ω) Alternate Channel Selectivity (400 kHz): 65 dB Frequency Response: 40 Hz to 15 000 Hz Stereo Separation: 35 dB Capture Ratio: 1.5 dB

[AM Tuner]

Sensitivity: 20 μV Selectivity: 35 dB

Page 32

Having TROUBLE with operation?

Please reset your unit

Refer to page of How to reset your unit

1005DTSMDTJEIN

Page 33

KD-G124/KD-G123

Installation/Connection Manual

GET0332-002A

[UI]

This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.

1005DTSMDTJEIN EN

WARNINGS

To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the unit.

• Be sure to ground this unit to the car’s chassis again after installation.

Notes:

• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio dealer.

• It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of the maximum power is less than 50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page 9 of the INSTRUCTIONS).

• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.

• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.

PRECAUTIONS on power supply and speaker connections:

• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be seriously damaged.

• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your car.

Parts list for installation and connection

The following parts are provided for this unit. After checking them, please set them correctly.

4 Ω to 8 Ω). If

Heat sink

A / B Hard case/Control panel

Washer (ø5)

Lock nut (M5)

Sleeve

Mounting bolt (M5 × 20 mm)

Trim plate

Rubber cushion

Power cord

Handles

INSTALLATION (IN-DASH MOUNTING)

The following illustration shows a typical installation. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying kits.

• If you are not sure how to install this unit correctly, have it installed by a qualified technician.

Do the required electrical connections.

Removing the unit

Before removing the unit, release the rear section.

When using the optional stay

Fire wall

When you stand the unit, be careful not to damage the fuse on the rear.

Stay (option)

When installing the unit without using the sleeve

In a Toyota car for example, first remove the car radio and install the unit in its place.

Insert the two handles, then pull them as illustrated so that the unit can be removed.

Flat type screws (M5 × 8 mm)

Bend the appropriate tabs to hold the sleeve firmly in place.

* Not supplied for this unit.

Dashboard

Screw (option)

Install the unit at an angle of less than 30˚.

Bracket*

Flat type screws (M5 × 8 mm)*

Pocket

Bracket*

Note : When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws. If longer screws are

used, they could damage the unit.

Page 34

ELECTRICAL CONNECTIONS

KD-G124 KD-G123

Typical connections

Before connecting:

The leads of the power cord and those of the connector from the car body may be different in color.

1 Connect the colored leads of the power cord in the order specified in the illustration below.

2 Connect the antenna cord.

3 Finally connect the wiring harness to the unit.

Rear ground

terminal

Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit.

Antenna terminal

Line out (see diagram

Before checking the operation of this unit prior to installation, this lead must be connected, otherwise power cannot be turned on.

White with black

stripe

White

15 A fuse

)

Black

To metallic body or chassis of the car

Yellow

Red

Blue

Blue with white stripe

GrayGray with black stripe

To a live terminal in the fuse block connecting to the car battery (bypassing the ignition switch) (constant 12 V)

To an accessory terminal in the fuse block

To the automatic antenna if any (250 mA max.)

To the remote lead of other equipment (200 mA max.)

Green with black stripe

Not supplied for this unit.

Purple with black stripeGreen

Ignition switch

Fuse block

Purple

Connecting the external ampliﬁ er or subwoofer

You can connect an amplifier to upgrade your car stereo system.

• Connect the remote lead (blue with white stripe) to the remote lead of the other

equipment so that it can be controlled through this unit.

• Disconnect the speakers from this unit, connect them to the amplifier. Leave the

speaker leads of this unit unused.

Set “L/O MODE” to “REAR” (See page 9 of the INSTRUCTIONS.)

You can connect a power amplifier for rear speakers.

JVC Amplifier

Set “L/O MODE” to “WOOFER” (See page 9 of the INSTRUCTIONS.)

JVC Amplifier

Right speaker (front)Left speaker (front)

Rear speakers

Remote lead

Remote lead (Blue with white stripe)

To the remote lead of other equipment or automatic antenna if any

Right speaker (rear)Left speaker (rear)

Y-connector (not supplied for this unit)

Front speakers

You can also connect a subwoofer to the REAR LINE OUT terminals.

Subwoofer

TROUBLESHOOTING

• The fuse blows. * Are the red and black leads connected correctly?

• Power cannot be turned on. * Is the yellow lead connected?

• No sound from the speakers. * Is the speaker output lead short-circuited?

• Sound is distorted.

* Is the speaker output lead grounded? * Are the “–” terminals of L and R speakers grounded in common?

• Noise interfere with sounds. * Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?

• This unit becomes hot.

* Is the speaker output lead grounded? * Are the “–” terminals of L and R speakers grounded in common?

Firmly attach the ground wire to the metallic body or to the chassis of the car—to the

place uncoated with paint (if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the unit.

Signal cord (not supplied for this unit)

• This unit does not work at all. * Have you reset your unit?

Page 35

CD RECEIVER KD-G126/KD-G125

KD-G126/KD-G125

KD-G126

KD-G125

For canceling the display demonstration, see page 5.

ENGLISH

For installation and connections, refer to the separate manual.

INSTRUCTIONS

GET0331-001A

[U/UH]

Page 36

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and to

obtain the best possible performance from the unit.

IMPORTANT FOR LASER PRODUCTS

ENGLISH

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel.

3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

Warning:

If you need to operate the unit while driving, be sure to look ahead carefully or you may be involved in a traffic accident.

How to reset your unit

• Your preset adjustments will also be erased.

• If a disc is loaded, it will eject. Be careful not to

drop the disc.

How to forcibly eject a disc

• If this does not work, reset your unit.

• Be careful not to drop the disc when it ejects.

Caution on volume setting:

Discs produce very little noise compared with other sources. Lower the volume before playing a disc to avoid damaging the speakers by the sudden increase of the output level.

How to use the M MODE button

If you press M MODE, the unit goes into functions mode, then the number buttons work as different function buttons.

Ex.: When number button 2 works as

MO (monaural) button.

Time countdown indicator

To use these buttons for their original functions again after pressing M MODE, wait

for 5 seconds without pressing any of these buttons until the functions mode is cleared or press M MODE again.

Page 37

How to read this manual

• Button operations are mainly explained with the illustrations in the table below.

•

is used to indicate an indicator is

displayed for the corresponding operation.

• Some related tips and notes are explained in “More about this unit” (see pages 11 and 12).

Press briefly.

Press repeatedly.

Press either one.

Press and hold until your desired response begins.

Press and hold both buttons at the same time.

How to detach/attach the control

panel

Control panel — KD-G126 and KD-G125 ........ 4

Getting started ................................. 5

Basic operations .................................................... 5

Radio operations .............................. 6

Disc operations ................................. 7

Playing a disc in the unit ....................................... 7

Sound adjustments ........................... 8

General settings — PSM ................... 9

Maintenance .................................... 10

More about this unit ......................... 11

Troubleshooting ............................... 12

Specifications ................................... 13

ENGLISH

Detaching...

Attaching...

For safety...

• Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.

• Stop the car before performing any complicated operations.

Temperature inside the car...

If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes normal before operating the unit.

Page 38

Control panel — KD-G126 and KD-G125

Parts identification

ENGLISH

1 (standby/on/attenuator) button 2 SOURCE button 3 BAND button 4 Loading slot 5 Display window 6 0 (eject) button 7 EQ (equalizer) button 8

¢/4 buttons

9 Control dial p SEL (select) button q DISP (display) button w MO (monaural) button e SSM (Strong-station Sequential Memory)

button

r Number buttons t RPT (repeat) button y RND (random) button u M MODE button i

(control panel release) button

Display window

o DISC indicator ; RND a RPT (repeat) indicator s S. BASS (super bass) indicator d EQ (equalizer) indicator f Sound mode (C-EQ: custom equalizer)

indicators—JAZZ, CLASSIC, HIP HOP, POPS, ROCK, USER

g Source display Volume level indicator Time countdown indicator

h Main display j Tuner reception indicators— ST (stereo),

MO (monaural)

(disc random) indicator

Page 39

Getting started

Basic operations

~ Turn on the power.

Basic settings

• See also “General settings — PSM” on page 9.

ENGLISH

* You cannot select “DISC” as the

playback source if there is no disc in the loading slot.

1 Canceling the display

2 Setting the clock

! For FM/AM tuner

⁄ Adjust the volume.

Volume level indicator

Volume level appears.

@ Adjust the sound as you want. (See

page 8.)

To drop the volume in a moment (ATT)

To restore the sound, press it again.

To turn off the power

3 Finish the procedure.

To check the current clock time while the power is turned off

To check the other information while listening to the radio/a disc

Frequency/Elapsed playing time Ô Clock

demonstrations

Select “DEMO,” then “DEMO OFF.”

Select “CLOCK H” (hour), then adjust the hour. Select “CLOCK M” (minute), then adjust the minute.

Page 40

Radio operations

ENGLISH

When an FM stereo broadcast is hard to receive

Lights up when monaural mode is activated.

Lights up when receiving an FM stereo broadcast with sufficient signal strength.

Selected band appears.

! Start searching for a station.

When a station is received, searching stops. To stop searching, press the same button again.

To tune in to a station manually

In step ! above... 1

2 Select the desired station frequencies.

Reception improves, but stereo effect will be lost. To restore the stereo effect, repeat the same procedure “MONO OFF” appears and the MO indicator goes off.

Storing stations in memory

You can preset six stations for each band.

FM station automatic presetting —

SSM (Strong-station Sequential Memory)

1 Select the FM band (FM1 – FM3) you

want to store into.

“SSM” flashes, then disappears when automatic presetting is over.

Local FM stations with the strongest signals are searched and stored automatically in the FM band.

Page 41

Manual presetting

Ex.: Storing FM station of 92.5 MHz into preset

number 4 of the FM1 band.

Preset number flashes for a while.

Listening to a preset station

Disc operations

Playing a disc in the unit

ENGLISH

All tracks will be played repeatedly until you change the source or eject the disc.

To stop play and eject the disc

To fast-forward or reverse the track

To go to the next or previous tracks

To locate a particular track directly

To select a number from 01 – 06:

2 Select the preset station (1 – 6) you

want.

To select a number from 07 – 12:

Prohibiting disc ejection

You can lock a disc in the loading slot.

To cancel the prohibition, repeat the same procedure.

Page 42

Selecting the playback modes

You can use only one of the following playback modes at a time.

ENGLISH

2 Select your desired playback mode.

Adjusting the sound

You can adjust the sound characteristics to your preference.

7 Repeat play

Mode Plays repeatedly

TRK RPT : The current track. RPT OFF : Cancels.

7 Random play

Mode Plays at random

DISC RND : All tracks of the current disc.

RND OFF : Cancels.

Sound adjustments

You can select a preset sound mode suitable to the music genre (C-EQ: custom equalizer).

Preset values

Indication (For)

USER (Flat sound)

ROCK

(Rock or disco music)

CLASSIC

(Classical music)

POPS (Light music)

HIP HOP

(Funk or rap music)

JAZZ (Jazz music)

BAS TRE S.BS

(bass) (treble)

00 00 OFF

+03 +01 ON

+01 –02 OFF

+04 +01 OFF

+02 00 ON

+02 +03 OFF

(super

bass)

Displayed only when “L/O MODE” is set to

“WOOFER” (see page 9).

Indication, [Range]

BAS*2 (bass), [–06 to +06]

Adjust the bass.

TRE*

(treble), [–06 to +06]

Adjust the treble.

FAD*

(fader), [R06 to F06]

Adjust the front and rear speaker balance.

BAL*

(balance), [L06 to R06]

Adjust the left and right speaker balance.

S.BS*2 (super bass), [S.BS ON or S.BS OFF],

[01 to 05] Maintain the richness and fullness of the bass sound regardless of how low you set the volume.

SUB. W

Adjust the subwoofer output level when a subwoofer is connected.

VOL (volume), [00 to 30 or 50* Adjust the volume.

(subwoofer), [00 to 08]

When you adjust the bass, treble, or

super bass the adjustment you have made is stored for the currently selected sound mode (C-EQ) including “USER.”

If you are using a two-speaker system, set the

fader level to “00.”

This adjustment cannot affect the subwoofer

output.

Range adjustment for super bass is adjustable

only when it is set to “S.BS ON.”

Depending on the amplifier gain control

setting. (See page 9 for details.)

]

Page 43

General settings — PSM

You can change PSM (Preferred Setting Mode) items listed in the table that follows.

3 Adjust the PSM item selected.

4 Repeat steps 2 and 3 to adjust other

2 Select a PSM item.

5 Finish the procedure.

Indications Selectable settings, [reference page]

DEMO

Display

demonstration

CLOCK H

Hour adjustment

CLOCK M

Minute adjustment

L/O MODE

Line output mode

AMP GAIN

Amplifier gain

control

DEMO ON : [Initial]; Display demonstration will be activated automatically

if no operation is done for about 20 seconds, [5].

DEMO OFF : Cancels.

1 – 12, [5]

[Initial: 1 (1:00)]

00 – 59, [5]

[Initial: 00 (1:00)]

When connecting an amplifier or a subwoofer, set this correctly. REAR : [Initial]; Select if the REAR LINE OUT terminals are used for

connecting the speakers through an external amplifier.

WOOFER : Select if the REAR LINE OUT terminals are used for

connecting a subwoofer.

You can change the maximum volume level of this unit. LOW PWR : VOL 00 – VOL 30 (Select this if the maximum power of the

speaker is less than 50 W to avoid damaging the speaker.)

HIGH PWR : [Initial]; VOL 00 – VOL 50

ENGLISH

PSM items if necessary.

Page 44

Maintenance

How to clean the connectors

Frequent detachment will deteriorate the connectors.To minimize this possibility,

ENGLISH

periodically wipe the connectors with a cotton swab or cloth moistened with alcohol, being careful not to damage the connectors.

Connector

Moisture condensation

Moisture may condense on the lens inside the CD player in the following cases:

• After starting the heater in the car.

• If it becomes very humid inside the car. Should this occur, the CD player may malfunction.In this case, eject the disc and leave the unit turned on for a few hours until the moisture evaporates.

How to handle discs

When removing a disc from its case, press down the center

holder of the case and lift the disc out, holding it by the edges.

• Always hold the disc by the edges. Do not touch its recording surface.

When storing a disc into its case, gently insert the disc around the center holder (with the printed surface facing up).

• Make sure to store discs into the cases after use.

Center holder

To play new discs

To keep discs clean

A dirty disc may not play correctly. If a disc does become dirty, wipe it with a soft cloth in a straight line from center to edge.

• Do not use any solvent (for example, conventional record cleaner, spray, thinner, benzine, etc.) to clean discs.

Do not use the following discs:

Warped disc

Sticker

Disc

Sticker residue

Stick-on label

Page 45

More about this unit

Basic operations

Turning on the power

• By pressing SOURCE on the unit, you can also turn on the power. If the source is ready, playback also starts.

Turning off the power

• If you turn off the power while listening to a disc, disc play will start from where playback has been stopped previously, next time you turn on the power.

Selecting the sources

• When no disc is loaded in the unit, “DISC” cannot be selected.

Tuner operations

Storing stations in memory

• During SSM search...

– All previously stored stations are erased and

stations are stored newly.

–

Received stations are preset in No. 1 (lowest frequency) to No. 6 (highest frequency).

– When SSM is over, the station stored in

No. 1 will be automatically tuned in.

• When storing a station manually, a previously preset station is erased when a new station is stored in the same preset number.

Disc operations

Caution for DualDisc playback

• The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the use of NonDVD side of a DualDisc on this product may not be recommended.

General

• This unit has been designed to reproduce CDs, and CD-Rs (Recordable)/CD-RWs (Rewritable) in audio CD (CD-DA) format.

• When a disc has been loaded, selecting “DISC” for the playback source starts disc play.

Inserting a disc

• When a disc is inserted upside down, the disc automatically ejects.

• Do not insert 8 cm discs (single CD) and unusual shape discs (heart, flower, etc.) into the loading slot.

Playing a CD-R or CD-RW

• Use only “finalized” CD-Rs or CD-RWs.

• This unit can play back multi-session discs; however, unclosed sessions will be skipped while playing.

• Some CD-Rs or CD-RWs may not play back on this unit because of their disc characteristics, and for the following causes:

– Discs are dirty or scratched. – Moisture condensation occurs on the lens

inside the unit. – The pickup lens inside the unit is dirty. – CD-R/CD-RW on which the files are

written with “Packet Write” method. – There are improper recording conditions

(missing data, etc.) or media conditions

(stain, scratch, warp, etc.).

• CD-RWs may require a longer readout time

since the reflectance of CD-RWs is lower than that of regular CDs.

• Do not use the following CD-Rs or CD-RWs: – Discs with stickers, labels, or protective seal

stuck to the surface. – Discs on which labels can be directly

printed by an ink jet printer. Using these discs under high temperatures

or high humidity may cause malfunctions or damages to the unit.

Changing the source

• If you change the source, playback also stops

(without ejecting the disc).

Next time you select “DISC” for the playback

source, disc play starts from where it has been stopped previously.

To be continued...

ENGLISH

Page 46

Ejecting a disc

• If the ejected disc is not removed within 15 seconds, the disc is automatically inserted again into the loading slot to protect it from dust. (Disc will not play this time.)

ENGLISH

General settings—PSM

Troubleshooting

What appears to be trouble is not always serious. Check the following points before calling a service center.

Symptoms Remedies/Causes

• Sound cannot be heard from the speakers.

General

• This unit does not work at all. Reset the unit (see page 2).

• SSM automatic presetting does not work.

• Static noise while listening to the

FM/AM

radio.

• Disc automatically ejects. Insert the disc correctly.

• CD-R/CD-RW cannot be played back.

• Tracks on the CD-R/CD-RW cannot be skipped.

• Disc can be neither played back nor ejected.

Disc playback

• Disc sound is sometimes interrupted. • Stop playback while driving on rough roads.

• “NO DISC” appears on the display. Insert a playable disc into the loading slot.

• Adjust the volume to the optimum level.

• Check the cords and connections.

Store stations manually.

Connect the antenna firmly.

• Insert a finalized CD-R/CD-RW.

•

Finalize the CD-R/CD-RW with the component which you used for recording.

• Unlock the disc (see page 7).

• Eject the disc forcibly (see page 2).

• Change the disc.

• Check the cords and connections.

Page 47

Specifications

AUDIO AMPLIFIER SECTION

Maximum Power Output: Front: 50 W per channel Rear: 50 W per channel Continuous Power Output (RMS): Front: 19 W per channel into 4 Ω, 40 Hz

to 20 000 Hz at no more than 0.8% total harmonic distortion.

Rear: 19 W per channel into 4 Ω, 40 Hz

to 20 000 Hz at no more than 0.8%

2.0 V/20 kΩ load (full scale) Output Impedance: 1 kΩ Subwoofer-Out Level/Impedance:

2.0 V/20 kΩ load (full scale)

TUNER SECTION

Frequency Range: FM: 87.5 MHz to 108.0 MHz AM: 531 kHz to 1 602 kHz

CD PLAYER SECTION

GENERAL

Power Requirement: Operating Voltage:

1.2 kg (excluding accessories)

Design and specifications are subject to change without notice.

ENGLISH

[FM Tuner]

Usable Sensitivity: 11.3 dBf (1.0 μV/75 Ω) 50 dB Quieting Sensitivity:

16.3 dBf (1.8 μV/75 Ω) Alternate Channel Selectivity (400 kHz): 65 dB Frequency Response: 40 Hz to 15 000 Hz Stereo Separation: 35 dB Capture Ratio: 1.5 dB

[AM Tuner]

Sensitivity: 20 μV Selectivity: 35 dB

Page 48

Having TROUBLE with operation?

Please reset your unit

Refer to page of How to reset your unit

EN, TH

1005DTSMDTJEIN

Page 49

KD-G126/KD-G125

Installation/Connection Manual

°“√µ‘¥µ—Èß/§ŸË¡◊Õ°“√µ‘¥µ—Èß

GET0331-006A

[U/UH]

ENGLISH

WARNINGS

To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the unit.

• Be sure to ground this unit to the car’s chassis again after installation.

Notes:

• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio dealer.

• It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of

“AMP GAIN” setting to prevent the speakers from being damaged (see page 9 of the INSTRUCTIONS).

• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.

• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.

4 Ω to 8 Ω). If the maximum power is less than 50 W, change

1005DTSMDTJEIN EN, TH

‰∑¬

™ÿ¥ª√–°Õ∫π’È‰¥È√—∫°“√ÕÕ°·∫∫¡“‡æ◊ËÕ„™Èß“π°—∫√–∫∫ °√–·‰øøÈ““¬¥‘π¢—È«≈∫°√–·µ√ß 12 ‚«≈∑Ï À“°√∂¬πµÏ¢Õß§ÿ≥‰¡Ë‰ ¥È„™È√–∫∫π’È µÈÕß„™È‡§√◊ËÕß·ª≈ß°√–·‰ø™Ë«¬ ´÷Ëß“¡“√∂À“´◊ÈÕ‰¥È®“°√È“π¢“¬‡§√◊ËÕß‡’¬ß√∂¬πµÏ

JVC

§”‡µ◊Õπ

‡æ◊ËÕªÈÕß°—π°“√‡°‘¥‰øøÈ“≈—¥«ß®√ ¢Õ·π–π”„ÀÈª≈¥¢—È«·∫µ‡µÕ√’Ë≈∫ÕÕ° ·≈È«®÷ßµËÕ“¬‰ø°ËÕπµ‘¥µ—Èß‡§√◊ËÕß

• µ√«®Õ∫„ÀÈ·πË„®«Ë“‰¥È‡¥‘π“¬¥‘πµËÕ√–À«Ë“ß‡§√◊ËÕß°—∫µ—«∂—ß √∂¬πµÏ„À¡Ë·≈È«À≈—ß®“°µ‘¥µ—Èß

À¡“¬‡Àµÿ:

• „™Èæ‘°—¥®”‡æ“–·∑πø‘« À“°ø‘«Ï¢“¥∫ËÕ¬ „ÀÈª√÷°…“√È“ π¢“¬‡§√◊ËÕß‡’¬ß√∂¬πµÏ

• ¢Õ·π–π”„ÀÈµËÕ≈”‚æß ∑’Ë¡’°”≈—ß¢—∫ßÿ¥‡°‘π°«Ë“ 50 W (∑—Èß¥È“πÀπÈ“·≈–¥È“πÀ≈—ß ¡’§Ë“§«“¡µÈ“π∑“π 4 Ω ∂÷ß 8 Ω)

∂È“°”≈—ß¢—∫µË”°«Ë“

50 W „ÀÈ‡ª≈’Ë¬π§Ë“ “AMP GAIN” ‡æ◊ËÕªÈÕß°—π‰¡Ë„ÀÈ≈”‚æß™”√ÿ¥ (¥ŸÀπÈ“ 9 §”·π–π”)

• °“√ªÈÕß°—π°“√≈—¥«ß®√ ®–µÈÕßæ—π¢—È«“¬µ–°—Ë« ∑’Ë‰¡Ë„™È·≈È«¥È«¬‡∑ ªæ—π“¬‰ø

• ·ºËπ√–∫“¬§«“¡√ÈÕπ®–√ÈÕπ¡“°À≈—ß®“°„™È √–¡—¥√–«—ßÕ¬Ë“‰ª —¡º—‡¡◊ËÕ∂Õ¥™ÿ¥ª√–°Õ∫π’È

JVC

Heat sink

·ºËπ√–∫“¬§«“¡√ÈÕπ

PRECAUTIONS on power supply and speaker connections:

• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit

will be seriously damaged.

• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in

your car.

¢ÈÕ§«√√–«—ß”À√—∫°“√µËÕ·À≈Ëß®Ë“¬°”≈—ß·≈–≈”‚æß:

•

Õ¬Ë“µËÕ“¬µ–°—Ë«‡§‡∫‘≈°”≈—ß¢Õß≈”‚æß‡¢È“°—∫·∫µ‡µÕ√’Ë√∂¬πµÏ ¡‘©–π—Èπ ™ÿ¥ª√–°Õ∫®–‰¥È√—∫§«“¡‡’¬À“¬¡“°

• °ËÕπ∑’Ë®–µËÕ“¬µ–°—Ë«‡§‡∫‘≈°”≈—ß¢Õß≈”‚æß‡¢È“°—∫≈”‚æß „ÀÈµ√«®Õ∫°“√‡¥‘π“¬‰ø≈”‚æß„π√∂¢Õß§ÿ≥„ÀÈ‡√’¬∫√ÈÕ¬‡’¬°ËÕπ

Parts list for installation and connection

The following parts are provided for this unit. After checking them, please set them correctly.

A / B Hard case/Control panel

≈—ß∫√√®ÿ/ÀπÈ“ª—¥

Power cord

“¬‡§‡∫‘≈°”≈—ß

Sleeve

ª≈Õ°ÀÿÈ¡

Washer (ø5)

ª√–‡°Áπ«ß·À«π

√“¬°“√Ë«πª√–°Õ∫”À√—∫µ‘¥µ—Èß·≈–‡™◊ËÕ¡µËÕ°—π

«πª√–°Õ∫µËÕ‰ªπ’È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È À≈—ß®“°µ√«®Õ∫·≈È« ª√—∫µ—Èß‡§√◊ËÕß„ÀÈ∂Ÿ°µÈÕß

Trim plate

·ºËπ‚≈À–¢Õ∫·µËß

Lock nut (M5)

(ø5)

πÕµ≈ÁÕ§ (M5)

Mounting bolt (M5 × 20 mm)

≈—°µ‘¥ (M5 × 20 ¡¡.)

Rubber cushion

¬“ß°—π°√–·∑°

Handles

§—π∫—ß§—∫

Page 50

INSTALLATION (IN-DASH MOUNTING)

°“√µ‘¥µ—Èß (°“√ª√–°Õ∫·ºßÀπÈ“ª—∑¡Ï‡¢È“)

The following illustration shows a typical installation. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying kits.

• If you are not sure how to install this unit correctly, have it installed by a qualified technician.

¿“æµ—«Õ¬Ë“ßµËÕ‰ªπ’È·¥ß∂÷ß°“√µ‘¥µ—Èß·∫∫∑—Ë«‰ª À“°§ÿ≥¡’ª—≠À“À√◊ÕµÈÕß°“√¢ÈÕ¡Ÿ≈‡°’Ë¬«°—∫™ÿ¥µ‘¥µ—Èß °√ÿ≥“ª√÷°…“°—∫ºŸÈ¢“¬‡§√◊ËÕß‡’ ¬ß√∂¬πµÏ

•

JVC ¢Õß∑Ë“πÀ√◊Õ∫√‘…—

™ÿ¥ª√–°Õ∫ ∂È“§ÿ≥‰¡Ë·πË„®«Ë“µ‘¥µ—Èß™ÿ¥ª√–°Õ∫π’È∂Ÿ°µÈÕßÀ√◊Õ‰¡Ë „ÀÈÀ“™Ë“ßºŸÈ‡™’Ë¬«™“≠‡ªÁπºŸÈµ‘¥µ—Èß

Do the required electrical connections.

µËÕ“¬‰øµ“¡∑’Ë°”Àπ¥‰«È∑—ÈßÀ¡¥

When you stand the unit, be careful not to damage the fuse on the rear.

‡¡◊ËÕ§ÿ≥µ—Èß™ÿ¥ª√–°Õ∫¢÷Èπ √–«—ßÕ¬Ë“∑”„ÀÈø‘«Ï∫√‘‡«≥Ë«π∑È“¬‡’¬À“¬

Removing the unit

Before removing the unit, release the rear section.

°“√∂Õ¥™ÿ¥ª√–°Õ∫

°ËÕπ®–∂Õ¥™ÿ¥ª√–°Õ∫ „ÀÈª≈¥ÀπÈ“µ—¥Ë«π∑È“¬°ËÕπ

Insert the two handles, then pull them as illustrated so that the unit can be removed.

„Ë§—π∫—ß§—∫ 2 Õ —π≈ß„π√ËÕß”À√—∫„™Èæ—π≈«¥ ¥—ß¿“æ ®“°π—Èπ „ÀÈ‡≈◊ËÕπ™ÿ¥ª√–°Õ∫ÕÕ° „π¢≥–∑’Ë§ËÕ¬ Ê ¥÷ß§—π∫—ß§—∫∑—Èß

Õ—πÕÕ°®“°°—π

Bend the appropriate tabs to hold the sleeve firmly in place.

ßÕ·ºËπ‡æ◊ËÕ¬÷¥ª≈Õ°„ÀÈµËÕ°—π‡¢È“∑’Ë

Õß

When using the optional stay / ‡¡◊ËÕ„™Èµ—«¬÷¥·∫∫‡≈◊Õ°‰¥È

Stay (option)

µ—«¬÷¥ (‡≈◊Õ°‰¥È)

Fire wall

ºπ—ß°—π‰ø

Dashboard

·ºßÀπÈ“ª—∑¡á

Screw (option)

°√Ÿ (‡≈◊Õ°‰¥È)

When installing the unit without using the sleeve / ‡¡◊ËÕµ‘¥µ—Èß™ÿ¥ª√–°Õ∫‚¥¬‰¡Ë„™Èª≈Õ°ÀÿÈ¡

In a Toyota car for example, first remove the car radio and install the unit in its place.

µ—«Õ¬Ë“ß‡™Ëπ „π√∂¬πµÏ‚µ‚¬µÈ“ „ÀÈ∂Õ¥«‘∑¬ÿµ‘¥√∂¬πµÏÕÕ°°ËÕπ ·≈È«®÷ßµ‘¥µ—Èß‡§√◊ËÕßπ’È‡¢È“·∑π∑’Ë

Flat type screws (M5 × 8 mm)*

°√ŸÀ—«‡√’¬∫ (M5 × 8 ¡¡.)*

Bracket*

·∑Ëπ√Õß√—∫*

Pocket

°–‡ª“–

Bracket*

·∑Ëπ√Õß√—∫*

* Not supplied for this unit.

‰¡Ë‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È

Flat type screws (M5 × 8 mm)*

°√ŸÀ—«‡√’¬∫ (M5 × 8 ¡¡.)*

Install the unit at an angle of less than 30˚.

µ‘¥µ—Èß™ÿ¥ª√–°Õ∫∑’Ë¡ÿ¡µË”°«Ë“ 30˚ Õß»“

Note : When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws. If longer screws are

used, they could damage the unit.

À¡“¬‡Àµ : ‡¡◊ËÕµ‘¥µ—Èß™ÿ¥ª√–°Õ∫≈ß„π·∑Ëπ√Õß√—∫‰«È „ÀÈ„™È°√Ÿ¬“«¢π“¥ 8

¡¡.

∂È“„™È°√Ÿ¬“«°«Ë“π’ÈÕ“®∑”„ÀÈ™ÿ¥ª√–°Õ∫‡’¬À“¬‰¥ô

Page 51

ENGLISH ‰∑¬

ELECTRICAL CONNECTIONS

Typical connections / °“√‡™◊ËÕ¡µËÕ·∫∫ª°µ

Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious

damage to this unit. The leads of the power cord and those of the connector from the car body may be different in color.

1 Connect the colored leads of the power cord in the order specified in the illustration below.

2 Connect the antenna cord.

3 Finally connect the wiring harness to the unit.

Rear ground

terminal

°“√‡™◊ËÕ¡‚¥¬„™È‰øøÈ“

°ËÕ•∑”°“•‡™•ËÕ¡µËÕ: µ•«®†Õ•°“•‡¥‘•†“¬‰ø„•••¬•µÏÕ¬Ë“ß•–¡—¥•–«—Õ¬Ë“„ÀÈº‘¥æ•“¥„•°“•‡™•ËÕ¡µËÕ™ÿ¥ª•–°Õ•™ÿ¥•’

°“•‡™•ËÕ¡µËÕº‘¥æ•“¥Õ“®∑”„ÀÈ‡°‘¥§«“¡‡†’¬À“¬•È“¬·•ß°—•™ÿ¥ª•– °Õ••’È‰¥È“•µ–°—Ë«¢Õß†“¬‰ø ·•–¢ÕßÕÿª°••ÏµËÕ‡™•ËÕ¡®“°µ—«• ß••Õ“®¡’’ ∑’Ë‰¡Ë‡À¡•Õ•°—

1 µËÕ“¬‰ø’µ“¡≈”¥—∫∑’Ë√–∫ÿ„π√Ÿª¥È“π≈Ë“ß 2 ‡™◊ËÕ¡µËÕ°—∫“¬Õ“°“» 3 ÿ¥∑È“¬ µËÕË«π§«∫§ÿ¡°“√‡¥‘π“¬‰ø‡¢È“°—∫™ÿ¥ª√–°Õ∫™ÿ¥π’È

®ÿ¥‡™◊ËÕ¡µËÕ

“¬¥‘π¥È“πÀ≈—ß

15 A fuse

ø‘«Ï¢π“¥ 15 A

Antenna terminal

¢—È«“¬Õ“°“»

Line out (see diagram

“¬ÕÕ° (¥Ÿ·ºπ¿Ÿ¡ )

)

Black

’¥”

Yellow *

’‡À≈◊Õß *

Red

’·¥ß

To metallic body or chassis of the car

Not supplied for this unit.

‰¡Ë‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È

Ignition switch

«‘∑™Ï®ÿ¥√–‡∫‘¥

µËÕ°—∫‚§√ß‚≈À–À√◊Õ‡™´‘¢Õß√∂¬πµá

To a live terminal in the fuse block connecting to the car battery (bypassing the ignition switch) (constant 12 V)

µËÕ°—∫¢—È«∑’Ë¡’°√–·‰øøÈ“„π·ºßø‘«Ï ´÷ËßµËÕ°—∫·∫µ‡µÕ√’Ë√∂¬πµ (‚¥¬‰¡ËµÈÕß„™È«‘∑™Ï®ÿ¥√–‡∫‘¥) (

12 ‚«≈∑Ï§ß∑’Ë)

Fuse block

·ºßø‘«

To an accessory terminal in the fuse block

µËÕ°—∫¢—È«Ë«πª√–°Õ∫„π·ºßø‘«

Before checking the operation of this unit prior to installation, this lead must be connected, otherwise power cannot be turned on.

°ËÕπ°“√µ√«®Õ∫°“√∑”ß“π¢Õß™ÿ¥ª√–°Õ∫π’È°ËÕπ∑’Ë®–µ‘¥µ—Èß

µÈÕßµËÕ“¬µ–°—Ë«π’È°ËÕπ ¡‘©–π—Èπ®–‰¡“¡“√∂‡ª‘¥‡§√◊ËÕß‰¥

White with black stripe

’¢“«·∂∫¥”

White

’¢“«

Gray with black stripe

’‡∑“·∂∫¥”

Blue

»’øÈ“

Blue with white stripe

’πÈ”‡ß‘π≈“¬¢“«

Gray

’‡∑“

Green with black stripe

’‡¢’¬«·∂∫¥”

To the automatic antenna if any (250 mA max.)

‡“Õ“°“»‰øøÈ“Õ—µ‚π¡—µ‘ À“°¡’ (¢π“¥Ÿß¸¥ 250 mA)

To the remote lead of other equipment (200 mA max.)

µËÕ‡¢È“°—∫Õª°√≥ÏÕË◊π (¢π“¥Ÿß¸¥ 200 mA

Green

’‡¢’¬«

Purple with black stripe

’¡Ë«ß·∂∫¥”

)

Purple

’¡Ë«ß

Left speaker (front)

≈”‚æß´È“¬ (ÀπÈ“)

Right speaker (front)

≈”‚æß¢«“ (ÀπÈ“)

Left speaker (rear)

≈”‚æß´È“¬ (À≈—ß)

Right speaker (rear)

≈”‚æß¢«“ (À≈—ß)

Page 52

KD-G126 KD-G125

Connecting the external amplifier or subwoofer / µËÕ·Õ¡ª≈‘ø“¬‡ÕÕ√ÏÀ√◊Õ´—∫«Ÿø‡øÕ√Ï¥È“ππÕ°

You can connect an amplifier to upgrade your car stereo system.

• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this unit.

• Disconnect the speakers from this unit, connect them to the amplifier. Leave the speaker

leads of this unit unused.

Set “L/O MODE” to “REAR” (See page 9 of the INSTRUCTIONS.)

µ—Èß§Ë“ “L/O MODE” ‡ªÁπ “REAR” (¥ŸÀπÈ“ 9 §”·π–π”)

You can connect a power amplifier for rear speakers.

∑Ë“π“¡“√∂µËÕ‡§√◊ËÕß¢¬“¬‡’¬ß‡ªÁπ≈”‚æßÀ≈—ß‰¥È

§ÿ≥“¡“√∂µËÕ°—∫·Õ¡æ≈‘ø“¬‡ÕÕ√Ï ‡æ◊ËÕ‡æ‘Ë¡§ÿ≥ ¿“æ‡’¬ß„ÀÈ°—∫√–∫∫‡µÕ√‘‚Õ¢Õß√∂¬πµÏ

• µËÕ“¬µ–°—Ë«√–¬–‰°≈ (’πÈ”‡ß‘π≈“¬¢“«) ‡¢È“°—∫“¬µ–°—Ë«√–¬–‰°≈¢ÕßÕÿª°√≥ÏÕ◊Ëπ Ê ‡æ◊ËÕ®–“¡“√∂§«∫§ÿ¡‚¥¬™ÿ¥ª√– °Õ∫π’È‰¥È

• ∂Õ¥≈”‚æßÕÕ°®“°™ÿ¥ª√–°Õ∫π’È ·≈È«µËÕ‡¢È“°—∫‡§√◊ËÕß¢¬“¬ ∑‘Èß“¬µ–°—Ë«≈”‚æß¢Õß™ÿ¥ª√–°Õ∫π’È‰«È

Remote lead

“¬µ–°—Ë«•–¬–‰°•

Remote lead (Blue with white stripe)

Y-connector (not supplied for this unit)

¢ÈÕµËÕ√Ÿªµ—« Y (‰¡Ë‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È)

“¬µ–°—Ë«•–¬–‰°• (’πÈ”‡ß‘π≈“¬¢“«)

To the remote lead of other equipment or automatic antenna if any

µËÕ“¬°—∫Õÿª°√≥ÏÕ◊ËπÀ√◊Õ‡“Õ“°“»Õ—µ‚π¡—µ‘∂È“¡’

JVC Amplifier

‡§√◊ËÕß¢¬“¬‡’¬ß JVC

Rear speakers

≈”‚æßÀ≈—ß

Set “L/O MODE” to “WOOFER” (See page 9 of the INSTRUCTIONS.)

µ—Èß§Ë“ “L/O MODE” ‡ªÁπ “WOOFER” (¥ŸÀπÈ“ 9 §”·π–π”)

You can also connect a subwoofer to the REAR LINE OUT terminals.

∑Ë“π¬—ß“¡“√∂µËÕ´—∫«Ÿø‡øÕ√Ï‡¢È“°—∫™ËÕßµËÕ—≠≠“≥ REAR LINE OUT ‰¥È

JVC Amplifier

‡§√◊ËÕß¢¬“¬‡’¬ß JVC

Subwoofer

´—∫«Ÿø‡øÕ√Ï

Front speakers

≈”‚æßÀπÈ“

Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with paint

(if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the unit.

Signal cord (not supplied for this unit)

TROUBLESHOOTING

• The fuse blows. * Are the red and black leads connected correctly?

• Power cannot be turned on. * Is the yellow lead connected?

• No sound from the speakers. * Is the speaker output lead short-circuited?

• Sound is distorted.

* Is the speaker output lead grounded? * Are the “–” terminals of L and R speakers grounded in common?

• Noise interfere with sounds. * Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?

• This unit becomes hot.

* Is the speaker output lead grounded? * Are the “–” terminals of L and R speakers grounded in common?

• This unit does not work at all.

* Have you reset your unit?

µËÕ≈«¥“¬¥‘π„ÀÈ·πËπ‡¢È“°—∫µ—«∂—ß‡À≈Á° À√◊Õµ—«∂—ß√∂—µ√ßË«π ∑’Ë‰¡Ë¡’’‡§≈◊Õ∫ (À“°¡’’‡§≈◊Õ∫Õ¬ŸË „ÀÈ¢Ÿ¥’ÕÕ°°ËÕπ °ËÕπµËÕ≈«¥

“¬‡§‡∫‘≈—≠≠“≥ (‰¡Ë‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È)



“¬¥‘π) À“°‰¡ËªØ‘∫—µ‘µ“¡§”·π–π”π’È ‡§√◊ËÕßÕ“®™”√ÿ¥À√◊Õ‡’¬À“¬‰¥

°“√µ√«®Õ∫ª—≠À“¢—¥¢ÈÕß

• ø‘«Ï¢“¥

* ¡’°“√‡™◊ËÕ¡ “¬µ–°—Ë«’¥”·≈–’·¥ßÕ¬Ë“ß∂Ÿ°µÈÕßÀ√◊Õ‰¡Ë

• ‰¡Ë“¡“√∂‡ª‘¥‡§√◊ËÕß‰¥È

* ¡’°“√‡™◊ËÕ¡“¬µ–°—Ë«’‡À≈◊ÕßÀ√◊Õ‰¡Ë

• ‰¡Ë¡’‡’¬ßÕÕ°®“°≈”‚æß

* “¬µ–°—Ë«Ë«π∑’ËÕÕ°∑“ß≈”‚æß‡°‘¥‰øøÈ“≈—¥«ß®√À√◊Õ‰¡Ë

• ‡’¬ß‡æ’È¬π

* “¬µ–°—Ë«Ë«π∑’ËÕÕ°∑“ß≈”‚æßµËÕ≈ß¥‘πÀ√◊Õ‰¡Ë * “¬¢—È«≈∫ “–” ¢Õß≈”‚æß¥È“π´È“¬·≈–¢«“µËÕ≈ß¥‘πµ“¡ª°µ‘À√◊Õ‰¡Ë

• ‡’¬ß√∫°«π

* ¡’°“√„™È“¬—ÈπÊ À√◊ÕÀπ“Ê µËÕ®“°‡§√◊ËÕß«π∑’Ëµ‘¥µ—Èß ‰«È∫πæ◊Èπ¥È“πÀ≈—ß°—∫µ—«∂—ß√∂¬πµÏÀ√◊Õ‰¡Ë

• ™ÿ¥ª√–°Õ∫√ÈÕπ¢÷Èπ

• ‡§√◊ËÕß√—∫π’È∑”ß“π‰¡

* ∑Ë“π‰¥Èµ—Èß‡§√◊ËÕß„À¡Ë·≈È«À√◊Õ¬—ß

Page 53

CD RECEIVER

RECEPTEUR CD

KD-G162/KD-G161

KD-G162

KD-G161

For canceling the display demonstration, see page 5. Pour annuler la démonstration des affichages, référez-vous à la page 5.

ENGLISH

FRANÇAIS

KD-G162

KD-G161

For installation and connections, refer to the separate manual. Pour l’installation et les raccordements, se référer au manuel séparé.

INSTRUCTIONS

MANUEL D’INSTRUCTIONS

GET0334-003A

[EX/EU]

Page 54

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and to

obtain the best possible performance from the unit.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

ENGLISH

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel.

3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

Warning:

If you need to operate the unit while driving, be sure to look ahead carefully or you may be involved in a traffic accident.

How to reset your unit

• Your preset adjustments will also be erased.

How to forcibly eject a disc

• If this does not work, reset your unit.

• Be careful not to drop the disc when it ejects.

How to detach/attach the control

panel

Detaching...

Attaching...

Note: Only for [EX] model users in UK and European countries For security reasons, a numbered ID card is provided with this unit, and the same ID number is imprinted on the unit’s chassis. Keep the card in a safe place, as it will help the

authorities to identify your unit if stolen.

Page 55

How to read this manual

• Button operations are mainly explained with the illustrations in the table below.

•

is used to indicate an indicator is

displayed for the correspnding operation.

• Some related tips and notes are explained in “More about this unit” (see pages 14 and 15).

Press briefly.

Press repeatedly.

Press and hold until your desired response begins.

Press and hold both buttons at the same time.

Press either one.

Control panel — KD-G162 and KD-G161 ........ 4

Getting started ................................. 5

Basic operations .................................................... 5

Radio operations .............................. 6

FM RDS operations ............................ 7

Searching for your favorite FM RDS programme ... 7

Disc operations ................................. 9

Playing a disc in the unit ...................................... 9

Sound adjustments ........................... 10

General settings — PSM ................... 11

Maintenance .................................... 13

More about this unit ......................... 14

Troubleshooting ............................... 16

Specifications ................................... 17

ENGLISH

How to use the M MODE button

If you press M MODE, the unit goes into functions mode, then the number buttons work as different function buttons.

Ex.: When number button 2 works as

MO (monaural) button.

Time countdown indicator

To use these buttons for their original functions again after pressing M MODE, wait

for 5 seconds without pressing any of these buttons until the functions mode is cleared or press M MODE again.

Caution on volume setting:

Discs produce very little noise compared with other sources. Lower the volume before playing a disc to avoid damaging the speakers by the sudden increase of the output level.

For safety...

• Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.

• Stop the car before performing any complicated operations.

Temperature inside the car...

If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes normal before operating the unit.

Page 56

Control panel — KD-G612/KD-G611/KD-G511

Control panel — KD-G162 and KD-G161

Parts identification

ENGLISH

1 (standby/on/attenuator) button 2 SOURCE button 3 BAND button 4 Loading slot 5 Display window 6 0 (eject) button 7 TP/PTY (traffic programme/programme

type) button

¢/4 buttons

9 Control dial p SEL (select) button q DISP (display) button w EQ (equalizer) button e MO (monaural) button r SSM (Strong-station Sequential Memory)

button

t Number buttons y RPT (repeat) button u RND (random) button

Display window

i M MODE button o

(control panel release) button

Display window

; DISC indicator a RND s RPT (repeat) indicator d LOUD (loudness) indicator f EQ (equalizer) indicator g Sound mode (C-EQ: custom equalizer)

indicators—JAZZ, CLASSIC, HIP HOP, POPS, ROCK, USER

h Source display / Volume level indicator /

Time countdown indicator

j Main display k RDS indicators—TP, PTY, AF, REG l Tuner reception indicators—ST (stereo),

MO (monaural)

(disc random) indicator

Page 57

Getting started

Basic operations

~ Turn on the power.

Basic settings

• See also “General settings — PSM” on pages 11 and 12.

ENGLISH

* You cannot select “DISC” as the

playback source if there is no disc in the unit.

! For FM/AM tuner

⁄ Adjust the volume.

Volume level appears.

Volume level indicator

@ Adjust the sound as you want. (See

page 10.)

To drop the volume in a moment (ATT)

To restore the sound, press it again.

To turn off the power

1 Canceling the display

demonstrations

Select “DEMO,” then “DEMO OFF.”

2 Setting the clock

Select “CLOCK H” (hour), then adjust the hour. Select “CLOCK M” (minute), then adjust the minute. Select “24H/12H,” then “24H” (hour) or “12H” (hour).

3 Finish the procedure.

To check the current clock time while...

The power is turned off

Listening to...

An FM (non-RDS) or AM station:

Frequency Ô Clock

An FM RDS station:

Station name (PS) = Station Frequency = Programme type (PTY) = Clock = (back to

the beginning)

Listening to a disc...

Elapsed playing time with track number Ô Clock

Page 58

Radio operations

ENGLISH

When an FM stereo broadcast is hard to receive

Lights up when receiving an FM stereo broadcast with sufficient signal strength.

Selected band appears.

! Start searching for a station.

When a station is received, searching stops. To stop searching, press the same button again.

To tune in to a station manually

In step ! above... 1

2 Select the desired station frequencies.

Lights up when monaural mode is activated.

Reception improves, but stereo effect will be lost.

To restore the stereo effect, repeat the same procedure. “MONO OFF” appears and the MO indicator goes off.

Storing stations in memory

You can preset six stations for each band.

FM station automatic presetting —

SSM (Strong-station Sequential Memory)

1 Select the FM band (FM1 – FM3) you

want to store into.

“SSM” flashes, then disappears when automatic presetting is over.

Local FM stations with the strongest signals are searched and stored automatically in the FM band.

Page 59

Manual presetting

Ex.: Storing FM station of 92.5 MHz into preset

number 4 of the FM1 band.

Preset number flashes for a while.

Listening to a preset station

FM RDS operations

What you can do with RDS

RDS (Radio Data System) allows FM stations to send an additional signal along with their regular programme signals. By receiving the RDS data, this unit can do the

following:

•

Programme Type (PTY) Search (see the following)

• TA (Traffic Announcement) and PTY

Standby Receptions (see pages 8 and 12)

•

Tracing the same programme automatically —Network-Tracking Reception (see page 9)

• Programme Search (see page 12)

Searching for your favorite FM RDS programme

You can tune in to a station broadcasting your favorite programme by searching for a PTY code.

•

To store your favorite programme types, see page 8.

ENGLISH

2 Select the preset station (1 – 6) you

want.

~ The last selected PTY

code appears.

Ÿ Select one of your favorite

programme types.

Select one of the PTY codes (see

page 15).

To be continued...

Page 60

! Start searching for your favorite

programme.

If there is a station broadcasting a programme

ENGLISH

Storing your favorite programme

You can store six favorite programme types.

Preset programme types in the number buttons (1 to 6):

1 Select a PTY code (see page 7). 2 Select the preset number (1 – 6) you

want to store into.

of the same PTY code as you have selected, that station is tuned in.

types

Using the standby receptions

TA Standby Reception

TA Standby Reception allows the unit to switch temporarily to Traffic Announcement (TA) from any source other than AM. The volume changes to the preset TA volume level if the current level is lower than the preset level (see page 12).

To activate TA Standby Reception

The TP (Traffic Programme)

indicator either lights up or flashes.

• If the TP indicator lights up, TA Standby Reception is activated.

• If the TP indicator flashes, TA Standby Reception is not yet activated. (This occurs when you are listening to an FM station without the RDS signals required for TA Standby Reception.)

To activate TA Standby Reception, tune in to

another station providing these signals. The TP indicator will stop flashing and remain lit.

To deactivate the TA Standby Reception

The TP indicator goes off.

Ex.: When “ROCK M” is selected

3 Repeat steps 1 and 2 to store other

PTY codes into other preset numbers.

4 Finish the procedure.

PTY Standby Reception

PTY Standby Reception allows the unit to switch temporarily to your favorite PTY programme from any source other than AM.

To activate and select your favorite PTY code for PTY Standby Reception, see page 12.

The PTY indicator either lights up or flashes.

• If the PTY indicator lights up, PTY Standby Reception is activated.

• If the PTY indicator flashes, PTY Standby Reception is not yet activated. To activate PTY Standby Reception, tune in to another station providing these signals. The PTY indicator will stop flashing and remain lit.

To deactivate the PTY Standby Reception, select “OFF” for the PTY code (see page 12). The PTY indicator goes off.

Page 61

Tracing the same programme—

Network-Tracking Reception

When driving in an area where FM reception is not sufficient enough, this unit automatically tunes in to another FM RDS station of the same network, possibly broadcasting the same programme with stronger signals (see the illustration on page 15).

When shipped from the factory, NetworkTracking Reception is activated.

To change the Network-Tracking Reception setting, see “AF-REG” on page 11.

Disc operations

To locate a particular track

To select a number from 01 – 06:

To select a number from 07 – 12:

Prohibiting disc ejection

You can lock a disc in the loading slot.

ENGLISH

Playing a disc in the unit

All tracks will be played repeatedly until you change the source or eject the disc.

To stop play and eject the disc

To fast-forward or reverse the track

To go to the next or previous tracks

To cancel the prohibition, repeat the same procedure.

Selecting the playback modes

You can use only one of the following playback modes at a time.

2 Select your desired playback mode.

7 Repeat play

Mode Plays repeatedly

TRK RPT : The current track. RPT OFF : Cancels.

7 Random play

Mode Plays at random

DISC RND : All tracks of the current disc.

RND OFF : Cancels.

Page 62

Sound adjustments

You can select a preset sound mode suitable to the music genre (C-EQ: custom equalizer).

Adjusting the sound

You can adjust the sound characteristics to your preference.

ENGLISH

Preset values

Indication (For)

USER (Flat sound)

ROCK

(Rock or disco music)

CLASSIC

(Classical music)

POPS (Light music)

HIP HOP

(Funk or rap music)

JAZZ (Jazz music)

Ex.: When “ROCK” is selected

BAS TRE LOUD

(bass) (treble)

00 00 OFF

+03 +01 ON

+01 –02 OFF

+04 +01 OFF

+02 00 ON

+02 +03 OFF

(loudness)

Indication, [Range]

BAS*1 (bass), [–06 to +06]

Adjust the bass.

TRE*1 (treble), [–06 to +06]

Adjust the treble.

FAD*

(fader), [R06 to F06]

Adjust the front and rear speaker balance.

BAL (balance), [L06 to R06] Adjust the left and right speaker balance.

LOUD*1 (loudness), [LOUD ON or LOUD OFF]

Boost low and high frequencies to produce a well-balanced sound at low volume level.

VOL (volume), [00 to 30 or 50* Adjust the volume.

When you adjust the bass, treble, or loudness,

the adjustment you have made is stored for the currently selected sound mode (C-EQ) including “USER.”

If you are using a two-speaker system, set the

fader level to “00.”

Depending on the amplifier gain control

setting. (See page 12 for details.)

]

Page 63

General settings — PSM

You can change PSM (Preferred Setting Mode) items listed in the table below.

3 Adjust the PSM item selected.

2 Select a PSM item.

4 Repeat steps 2 and 3 to adjust other

PSM items if necessary.

5 Finish the procedure.

Indications Selectable settings, [reference page]

DEMO

Display demonstration

CLOCK H

Hour adjustment

CLOCK M

Minute adjustment

DEMO ON : [Initial]; Display demonstration will be activated

automatically if no operation is done for about 20 seconds, [5].

DEMO OFF : Cancels.

0 – 23 (1 – 12), [5]

[Initial: 0 (0:00)]

00 – 59, [5]

[Initial: 00 (0:00)]

ENGLISH

24H/12H

Time display mode

CLK ADJ

Clock adjustment

AF-REG

Alternative frequency/ regionalization reception

12H O 24H, [5]

[Initial: 24H]

AUTO : [Initial]; The built-in clock is automatically adjusted

using the CT (clock time) data in the RDS signal.

OFF : Cancels.

When the received signals from the current FM RDS station become

weak...

AF : [Initial]; Switches to another station (the programme

may differ from the one currently received), [9].

• The AF indicator lights up. AF REG : Switches to another station broadcasting the same

programme.

• The AF and REG indicators light up. OFF : Cancels.

To be continued...

Page 64

Indications Selectable settings, [reference page]

PTY-STBY

PTY standby

TA VOL

Traffic announcement

ENGLISH

volume

P-SEARCH

Programme search

TEL

Telephone muting

AMP GAIN

Amplifier gain control

IF BAND

Intermediate frequency

band

Activates PTY Standby Reception with one of the PTY codes, [8].

OFF [Initial]

[Initial: VOL 15]; VOL 00 — VOL 30 or 50*, [8]

ON : Using the AF data, the unit tunes in to another

OFF : [Initial]; Cancels.

MUTING 1/MUTING 2 : Select either one which mutes the sounds

OFF : [Initial]; Cancels.

You can change the maximum volume level of this unit.

LOW PWR : VOL 00 – VOL 30 (Select this if the maximum power

HIGH PWR : [Initial]; VOL 00 – VOL 50

AUTO : [Initial]; Increase the tuner selectivity to reduce

WIDE : Subject to the interference noises from adjacent

PTY codes, [15] = (back to the beginning)

frequency broadcasting the same programme as the original preset RDS station is if the preset station signals are not sufficient.

while using a cellular phone.

of the speaker is less than 45 W to prevent them from damaging the speaker.)

interference noises between close stations. (Stereo effect may be lost.)

stations, but sound quality will not be degraded and maintains the stereo effect.

* Depends on the amplifier gain control.

Page 65

Maintenance

How to clean the connectors

Connector

To keep discs clean

A dirty disc may not play correctly. If a disc does become dirty, wipe it with a soft cloth in a straight line from center to edge.

• Do not use any solvent (for example, conventional record cleaner, spray, thinner, benzine, etc.) to clean discs.

To play new discs

ENGLISH

Moisture condensation

Moisture may condense on the lens inside the CD player in the following cases:

• After starting the heater in the car.

• If it becomes very humid inside the car. Should this occur, the CD player may malfunction. In this case, eject the disc and leave the unit turned on for a few hours until the moisture evaporates.

How to handle discs

When removing a disc from its case, press down the center

holder of the case and lift the disc out, holding it by the edges.

• Always hold the disc by the edges. Do not touch its recording surface.

When storing a disc into its case, gently insert the disc around the center holder (with the printed surface facing up).

• Make sure to store discs into the cases after use.

Center holder

Do not use the following discs:

Warped disc

Sticker

Disc

Sticker residue

Stick-on label

Page 66

More about this unit

Basic operations

Turning on the power

ENGLISH

• By pressing SOURCE on the unit, you can also turn on the power. If the source is ready, playback also starts.

Turning off the power

• If you turn off the power while listening to a disc, disc play will start from where playback has been stopped previously, next time you turn on the power.

Selecting the sources

• When no disc is loaded in the unit, “DISC”

cannot be selected.

Tuner operations

Storing stations in memory

• During SSM search...

– All previously stored stations are erased and

stations are stored newly.

– Received stations are preset in No. 1 (lowest

frequency) to No. 6 (highest frequency).

– When SSM is over, the station stored in

No. 1 will be automatically tuned in.

• When storing a station manually, the previously preset station is erased when a new station is stored in the same preset number.

• When Alternative Frequency Reception is activated (with AF selected), NetworkTracking Reception is also activated automatically. On the other hand, NetworkTracking Reception cannot be deactivated without deactivating Alternative Frequency Reception. (See page 11.)

• If you want to know more about RDS, visit «http://www.rds.org.uk».

Disc operations

Caution for DualDisc playback

• The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the use of NonDVD side of a DualDisc on this product may not be recommended.

General

• This unit has been designed to reproduce CDs, and CD-Rs (Recordable)/CD-RWs (Rewritable) in audio CD (CD-DA format).

• When a disc has been loaded, selecting “DISC” for the playback source starts disc play.

Inserting a disc

• When a disc is inserted upside down, the disc automatically ejects.

• Do not insert 8 cm discs (single CD) and unusual shape discs (heart, flower, etc.) into the loading slot.

FM RDS operations

• Network-Tracking Reception requires two types of RDS signals—PI (Programme Identification) and AF (Alternative Frequency) to work correctly. Without receiving these data correctly, NetworkTracking Reception will not operate correctly.

• If a Traffic Announcement is received, the volume level automatically changes to the preset level (TA VOL) if the current level is lower than the preset level.

Page 67

Playing a CD-R or CD-RW

• Use only “finalized” CD-Rs or CD-RWs.

• This unit can play back multi-session discs; however, unclosed sessions will be skipped while playing.

• Some CD-Rs or CD-RWs may not play back on this unit because of their disc characteristics, or for the following causes:

– Discs are dirty or scratched. – Moisture condensation occurs on the lens

inside the unit. – The pickup lens inside the unit is dirty. – CD-R/CD-RW on which the files are

written with “Packet Write” method. – There are improper recording conditions

(missing data, etc.) or media conditions

(stained, scratched, warped, etc.).

• CD-RWs may require a longer readout time

since the reflectance of CD-RWs is lower than that of regular CDs.

• Do not use the following CD-Rs or CD-RWs: – Discs with stickers, labels, or protective seal

stuck to the surface. – Discs on which labels can be directly

printed by an ink jet printer. Using these discs under high temperatures or

high humidities may cause malfunctions or damage to the unit.

General settings—PSM

PTY codes

NEWS, AFFAIRS, INFO, SPORT, EDUCATE, DRAMA, CULTURE, SCIENCE, VARIED, POP M (music), ROCK M (music), EASY M (music), LIGHT M (music), CLASSICS, OTHER M (music), WEATHER, FINANCE, CHILDREN, SOCIAL, RELIGION, PHONE IN, TRAVEL, LEISURE, JAZZ, COUNTRY, NATION M (music), OLDIES, FOLK M (music), DOCUMENT

Network-Tracking Reception

Programme A broadcasting on different frequency areas (01 – 05)

ENGLISH

Changing the source

• If you change the source, playback also stops (without ejecting the disc).

Next time you select “DISC” for the playback

source, disc play starts from where it has been stopped previously.

Ejecting a disc

• If the ejected disc is not removed within 15 seconds, the disc is automatically inserted again into the loading slot to protect it from dust. (Disc will not play this time.)

Page 68

Troubleshooting

What appears to be trouble is not always serious. Check the following points before calling a service center.

ENGLISH

Symptoms Remedies/Causes

• Sound cannot be heard from the speakers.

General

• The unit does not work at all. Reset the unit (see page 2).

• SSM automatic presetting does not work.

• Adjust the volume to the optimum level.

• Check the cords and connections.

Store stations manually.

FM/AM

• Static noise while listening to the radio. Connect the aerial firmly.

• Disc cannot be played back. Insert the disc correctly.

• CD-R/CD-RW cannot be played back.

• Tracks on the CD-R/CD-RW cannot be skipped.

• Disc can be neither played back nor ejected.

Disc playback

• Disc sound is sometimes interrupted. • Stop playback while driving on rough roads.

• “NO DISC” appears on the display. Insert a playable disc into the loading slot.

• Insert a finalized CD-R/CD-RW. Finalize the CD-R/CD-RW with the component

• which you used for recording.

• Unlock the disc (see page 9).

• Eject the disc forcibly (see page 2).

• Change the disc.

• Check the cords and connections.

Page 69

Specifications

AUDIO AMPLIFIER SECTION

Maximum Power Output: Front: 45 W per channel Rear: 45 W per channel Continuous Power Output (RMS): Front: 17 W per channel into 4 Ω, 40 Hz

to 20 000 Hz at no more than 0.8% total harmonic distortion.

Rear: 17 W per channel into 4 Ω, 40 Hz

to 20 000 Hz at no more than 0.8%

total harmonic distortion. Load Impedance: 4 Ω (4 Ω to 8 Ω allowance) Tone Control Range: Bass: ±10 dB at 100 Hz Treble: ±10 dB at 10 kHz Frequency Response: 40 Hz to 20 000 Hz Signal-to-Noise Ratio: 70 dB Line-Out Level/Impedance:

2.0 V/20 kΩ load (full scale) Output Impedance: 1 kΩ

TUNER SECTION

Frequency Range: FM: 87.5 MHz to 108.0 MHz AM: (MW) 522 kHz to 1 620 kHz (LW) 144 kHz to 279 kHz

CD PLAYER SECTION

Type: Compact disc player Signal Detection System: Non-contact optical

pickup (semiconductor laser) Number of Channels: 2 channels (stereo) Frequency Response: 5 Hz to 20 000 Hz Dynamic Range: 96 dB Signal-to-Noise Ratio: 98 dB Wow and Flutter: Less than measurable limit

GENERAL

Power Requirement: Operating Voltage: DC 14.4 V (11 V to 16 V allowance) Grounding System: Negative ground Allowable Operating Temperature: 0°C to +40°C Dimensions (W × H × D): Installation Size (approx.): 182 mm × 52 mm × 150 mm Panel Size (approx.): 188 mm × 58 mm × 11 mm Mass (approx.):

1.2 kg (excluding accessories)

ENGLISH

[FM Tuner]

Usable Sensitivity: 11.3 dBf (1.0 μV/75 Ω) 50 dB Quieting Sensitivity:

16.3 dBf (1.8 μV/75 Ω) Alternate Channel Selectivity (400 kHz): 65 dB Frequency Response: 40 Hz to 15 000 Hz Stereo Separation: 30 dB Capture Ratio: 1.5 dB

[MW Tuner]

Sensitivity: 20 μV Selectivity: 35 dB

[LW Tuner]

Sensitivity: 50 μV

Design and specifications are subject to change without notice.

Page 70

Having TROUBLE with operation?

Please reset your unit

Refer to page of How to reset your unit

Vous avez des PROBLÈMES de

fonctionnement?

Réinitialisez votre appareil

Référez-vous à la page intitulée Comment réinitialiser votre appareil

EN, FR

1005DTSMDTJEIN

Page 71

KD-G162/KD-G161

Installation/Connection Manual Manuel d’installation/raccordement

GET0334-010A

[EX/EU]

ENGLISH

WARNINGS

To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the unit.

• Be sure to ground this unit to the car’s chassis again after installation.

Notes:

• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC IN-CAR ENTERTAINMENT dealer.

• It is recommended to connect to the speakers with maximum power of more than 45 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less than 45 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page 12 of the INSTRUCTIONS).

• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.

• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.

1005DTSMDTJEIN EN, FR

FRANÇAIS

AVERTISSEMENTS

Pour éviter tout court-circuit, nous vous recommandons de débrancher la borne négative de la batterie et d’effectuer tous les raccordements électriques avant d’installer l’appareil.

• Assurez-vous de raccorder de nouveau la mise à la masse de cet appareil au châssis de la voiture après l’installation.

Remarques:

• Remplacer le fusible par un de la valeur précisée. Si le fusible saute souvent, consulter votre revendeur d’autoradios JVC.

• Il est recommandé de connecter des enceintes avec une puissance de plus de 45 W (les enceintes arrière et les enceintes avant, avec une impédance comprise entre 4 Ω et 8 Ω). Si la puissance maximum est inférieure à 45 W, changez “AMP GAIN” pour éviter d’endommager vos enceintes (voir page 12 du MANUEL D’INSTRUCTIONS).

• Pour éviter les court-circuits, couvrir les bornes des fils qui ne sont PAS UTILISÉS avec de la bande isolante.

• Le dissipateur de chaleur devient très chaud après usage. Faire attention de ne pas le toucher en retirant cet appareil.

Heat sink

Dissipateur de chaleur

PRECAUTIONS on power supply and speaker connections:

• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be seriously damaged.

• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your car.

PRECAUTIONS sur l’alimentation et la connexion des enceintes:

• NE CONNECTEZ PAS les fils d’enceintes du cordon d’alimentation à la batterie; sinon, l’appareil serait sérieusement endommagé.

• AVANT de connecter les fils d’enceintes du cordon d’alimentation aux enceintes, vérifiez le câblage des enceintes de votre voiture.

Parts list for installation and connection

The following parts are provided for this unit. After checking them, please set them correctly.

A / B Hard case/Control panel

Etui de transport/Panneau de commande

Power cord

Cordon d’alimentation

Sleeve

Manchon

Washer (ø5)

Rondelle (ø5)

Liste des pièces pour l’installation et raccordement

Les pièces suivantes sont fournies avec cet appareil. Après vérification, veuillez les placer correctement.

Trim plate

Plaque d’assemblage

Lock nut (M5)

Ecrou d’arrêt (M5)

Mounting bolt (M5 × 20 mm)

Boulon de montage (M5 × 20 mm)

Rubber cushion

Amortisseur en caoutchouc

Handles

Poignées

Page 72

INSTALLATION (IN-DASH MOUNTING)

Removing the unit

Before removing the unit, release the rear section.

Retrait de l’appareil

Avant de retirer l’appareil, libérer la section arrière.

INSTALLATION (MONTAGE DANS LE TABLEAU DE BORD)

The following illustration shows a typical installation. If you have any questions or require information regarding installation kits, consult your JVC IN-CAR ENTERTAINMENT dealer or a company supplying kits.

• If you are not sure how to install this unit correctly, have it installed by a qualified technician.

• Si l’on n’est pas sûr de pouvoir installer correctement cet appareil, le faire installer par un technicien qualifié.

Do the required electrical connections.

Réalisez les connexions électriques.

When you stand the unit, be careful not to damage the fuse on the rear.

Lorsque vous mettez l’appareil à la verticale, faire attention de ne pas endommager le fusible situé sur

l’arrière.

Bend the appropriate tabs to hold the sleeve firmly in place.

Tordez les languettes appropriées pour maintenir le manchon en place.

When using the optional stay / Lors de l’utilisation du hauban en option

Fire wall

Cloison

Dashboard

Tableau de bord

Stay (option)

Hauban (en option)

Screw (option)

Vis (en option)

Insert the two handles, then pull them as illustrated so that the unit can be removed.

Insérez les deux poignées, puis tirez de la façon illustrée de façon à retirer l’appareil.

When installing the unit without using the sleeve / Lors de l’installation de l’appareil scans utiliser de manchon

In a Toyota car for example, first remove the car radio and install the unit in its place.

Par exemple dans une Toyota, retirer d’abord l’autoradio et installer l’appareil à la place.

Flat type screws (M5 × 8 mm)

Vis à tête plate (M5 × 8 mm)*

Bracket*

Support*

Pocket

Poche

Flat type screws (M5 × 8 mm)*

Vis à tête plate (M5 × 8 mm)*

* Not supplied for this unit. * Non fourni avec cet autoradio.

Install the unit at an angle of less than 30˚.

Installez l’appareil avec un angle de moins de 30˚.

Bracket*

Support*

Note : When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws. If longer screws are

used, they could damage the unit.

Remarque : Lors de l’installation de l’appareil sur le support de montage, s’assurer d’utiliser des vis d’une longueur de 8 mm.

Si des vis plus longues sont utilisées, elles peuvent endommager l’appareil.

Page 73

ENGLISH FRANÇAIS

If your car is equipped with the ISO connector / Si votre voiture est équippée d’un connecteur ISO

• Connect the ISO connectors as illustrated.

• Connectez les connecteurs ISO comme montré sur l’illustration.

From the car body

De la carrosserie de la voiture

ISO connector of the supplied power cord

Connecteur ISO pour le cordon d’alimentation fourni

View from the lead side

Vue à partir du côté des fils

For some VW/Audi or Opel (Vauxhall) automobile / Pour certaine voiture VW/Audi ou Opel (Vauxhall)

You may need to modify the wiring of the supplied power cord as illustrated.

• Contact your authorized car dealer before installing this unit.

Vous aurrez peut-être besoin de modifier le câblage du cordon d’alimentation fourni comme montré sur l’illustration.

• Contactez votre revendeur automobile autorisé avant d’installer l’appareil.

Original wiring / Câblage original

ISO connector

Connecteur ISO

Y: Yellow

Jaune

R: Red

Rouge

Modified wiring 1 / Câblage modifié 1

Use modified wiring 2 if the unit does not turn on.

Utilisez le câblage modifié 2 si l’appareil ne se met pas sous tension.

Modified wiring 2 / Câblage modifié 2

Connections without using the ISO connectors / Connexions sans l’utilisation des connecteurs ISO

Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious

damage to this unit. The leads of the power cord and those of the connector from the car body may be different in color.

1 Cut the ISO connector. 2 Connect the colored leads of the power cord in the order specified in the illustration below. 3 Connect the aerial cord. 4 Finally connect the wiring harness to the unit.

Rear ground terminal

Borne arrière de masse

15 A fuse

Fusible 15 A

Aerial terminal

Borne de l’antenne

Line out (see diagram )

Sortie de ligne (voir le diagramme

)

Black

Noir

Avant de commencer la connexion: Vérifiez attentivement le câblage du véhicule. Une connexion incorrecte peut endommager sérieusement l’appareil. Le fil du cordon d’alimentation et ceux des connecteurs du châssis de la voiture peuvent être différents en couleur.

1 Coupez le connecteur ISO. 2 Connectez les fils colorés du cordon d’alimentation dans l’ordre spécifié sur l’illustration ci-dessous. 3 Connectez le cordon d’antenne. 4 Finalement, connectez le faisceau de fils à l’appareil.

Not supplied for this unit.

Non fourni avec cet autoradio.

To metallic body or chassis of the car

Vers corps métallique ou châssis de la voiture

Ignition switch

Interrupteur d’allumage

Before checking the operation of this unit prior to installation, this lead must be connected, otherwise power cannot be turned on.

Pour vérifier le fonctionnement de cet appareil avant

installation, ce fil doit être raccordé, sinon l’appareil ne peut pas être mis sous tension.

Yellow

Jaune *

Red

Rouge

Blue with white stripe

Bleu avec bande blanche

Brown Marron

To a live terminal in the fuse block connecting to the car battery (bypassing the ignition switch) (constant 12 V)

À une borne sous tension du porte-fusible connectée à la batterie de la voiture (en dérivant l’interrupteur d’allumage) (12 V constant)

Fuse block

Porte-fusible

To an accessory terminal in the fuse block

Vers borne accessoire du porte-fusible

To the remote lead of other equipment or power aerial if any (200 mA max.)

Au fil de télécommande de l’autre appareil ou à l’antenne automatique s’il y en a une (200 mA max.)

To cellular phone system

À un système de téléphone cellulaire

White with black stripe

Blanc avec bande noire

White

Blanc

Left speaker (front)

Enceinte gauche (avant)

Gray with black stripe

Gris avec bande noire

Gray

Gris

Right speaker (front)

Enceinte droit (avant)

Green with black stripe

Vert avec bande noire

Green

Vert

Left speaker (rear)

Enceinte gauche (arrière)

Purple with black stripe

Violet avec bande noire

Purple

Violet

Right speaker (rear)

Enceinte droit (arrière)

Page 74

Connecting the external amplifier / Connexion d’un amplificateur extérieur

You can connect an amplifier to upgrade your car stereo system.

• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this unit.

• Disconnect the speakers from this unit, connect them to the amplifier. Leave the speaker

leads of this unit unused.

Rear speakers

Enceintes arrière

JVC Amplifier

JVC Amplificateur

Vous pouvez connecter un amplificateur pour améliorer votre système autoradio.

• Connectez le fil de commande à distance (bleu avec bande blanche) au fil de commande à distance de

l’autre appareil de façon qu’il puisse être commandé via cet appareil.

• Déconnectez les enceintes de cet appareil et connectez-les à l’amplificateur. Laissez les fils d’enceintes de cet appareil inutilisés.

Remote lead

Fil d’alimentation à distance

Remote lead (Blue with white stripe)

Fil d’alimentation à distance (Bleu avec bande blanche)

Y-connector (not supplied for this unit)

Connecteur Y (non fourni avec cet autoradio)

To the remote lead of other equipment or power aerial if any

Au fil de télécommande de l’autre appareil ou à l’antenne automatique s’il y en a une

Cut the rear speaker leads of the car’s

ISO connector and connect them to the amplifier.

Coupez les fils des enceintes arrière du

connecteur ISO de la voiture et connectez-les à l’amplificateur.

Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place not coated with

paint (if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the unit.

Signal cord (not supplied for this unit)

Rear speakers

Enceintes arrière

Front speakers (see diagram )

Enceintes avant (voir le diagramme )

Attachez solidement le fil de mise à la masse au châssis métallique de la voiture—à un endroit qui n’est

pas recouvert de peinture (s’il est recouvert de peinture, enlevez d’abord la peinture avant d’attacher le fil). L’appareil peut être endommagé si cela n’est pas fait correctement.

Cordon de signal (non fourni avec cet autoradio)

TROUBLESHOOTING

• The fuse blows. * Are the red and black leads connected correctly?

• Power cannot be turned on. * Is the yellow lead connected?

• No sound from the speakers. * Is the speaker output lead short-circuited?

• Sound is distorted.

* Is the speaker output lead grounded? * Are the “–” terminals of L and R speakers grounded in common?

• Noise interfere with sounds. * Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?

• This unit becomes hot.

* Is the speaker output lead grounded? * Are the “–” terminals of L and R speakers grounded in common?

• This unit does not work at all. * Have you reset your unit?

EN CAS DE DIFFICULTES

• Le fusible saute.

* Les fils rouge et noir sont-ils racordés correctement?

• L’appareil ne peut pas être mise sous tension.

* Le fil jaune est-elle raccordée?

• Pas de son des enceintes.

* Le fil de sortie d’enceinte est-il court-circuité?

• Le son est déformé.

* Le fil de sortie d’enceinte est-il à la masse? * Les bornes “–” des enceintes gauche et droit sont-elles mises ensemble à la masse?

• Interférence avec les sons.

* La prise arrière de mise à la terre est-elle connectée au châssis de la voiture avec un cordon court et épais?

• L’appareil devient chaud.

* Le fil de sortie d’enceinte est-il à la masse? * Les bornes “–” des enceintes gauche et droit sont-elles mises ensemble à la masse?

• Cet appareil ne fonctionne pas du tout.

* Avez-vous réinitialisé votre appareil?

JVC KD-G120R, KD-G120 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

CD RECEIVER KD-G120R/KD-G120

INSTRUCTIONS

INFORMATION (For U.S.A.)

Warning:

IMPORTANT FOR LASER PRODUCTS

CONTENTS

Caution on volume setting:

For safety...

Temperature inside the car...

Remote controller — RM-RK50

Getting started

Radio operations

Disc operations

Sound adjustments

General settings — PSM

Maintenance

More about this unit

Troubleshooting

Specifications

WARNINGS

ELECTRICAL CONNECTIONS CONEXIONES ELECTRICAS RACCORDEMENTS ELECTRIQUES

TROUBLESHOOTING

KD-G124/KD-G123

INSTRUCTIONS

IMPORTANT FOR LASER PRODUCTS

Warning:

Caution on volume setting:

CONTENTS

For safety...

Temperature inside the car...

Getting started

Radio operations

Disc operations

Sound adjustments

General settings — PSM

Maintenance

More about this unit

Troubleshooting

Specifications

Installation/Connection Manual

WARNINGS

INSTALLATION (IN-DASH MOUNTING)

ELECTRICAL CONNECTIONS

TROUBLESHOOTING

KD-G126/KD-G125

INSTRUCTIONS

IMPORTANT FOR LASER PRODUCTS

Warning:

Caution on volume setting:

CONTENTS

For safety...

Temperature inside the car...

Getting started

Radio operations

Disc operations

Sound adjustments

General settings — PSM

Maintenance

More about this unit

Troubleshooting

Specifications

Installation/Connection Manual

WARNINGS

INSTALLATION (IN-DASH MOUNTING)

ELECTRICAL CONNECTIONS

TROUBLESHOOTING

KD-G162/KD-G161

INSTRUCTIONS

IMPORTANT FOR LASER PRODUCTS

Warning:

CONTENTS

Caution on volume setting:

For safety...

Temperature inside the car...

Getting started

Radio operations