JVC KD-G116, KD-G115AB, KD-G115AT, KD-G115AU, KD-G116AB Instructions Manual

CD RECEIVER KD-G116/KD-G115

KD-G116/KD-G115

ENGLISH

For canceling the display demonstration, see page 7.

For installation and connections, refer to the separate manual.

INSTRUCTIONS

GET0252-001A

[U/UH]

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and to

obtain the best possible performance from the unit.

ENGLISH

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave

all servicing to qualified service personnel.

3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated.

Avoid direct exposure to beam.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

Warning:

If you need to operate the receiver while
driving, be sure to look ahead carefully or
you may be involved in a traffic accident.

How to forcibly eject a disc

If a disc cannot be recognized by the
receiver or cannot be ejected, ejects the disc
as follows.

How to reset your unit

• This will reset the microcomputer. Your
preset adjustments will also be erased.

• If a disc is loaded, it will eject. Be careful
not to drop the disc.

• If this does not work, try to reset your
receiver.

• Be careful not to drop the disc when it
ejects.

2

Contents

How to reset your unit ........................... 2

How to forcibly eject a disc................... 2

How to read this manual........................ 4

How to use the MODE button ............... 4

Control panel

— KD-G116/KD-G115 ............... 5

Parts identification................................. 5

Getting started....................... 6

Basic operations ........................... 6

Canceling the display demonstrations ... 7

Setting the clock .................................... 7

Radio operations ................... 8

Listening to the radio........................... 8

Storing stations in memory.................... 9

Listening to a preset station ................... 9

Disc operations ...................... 10

Playing a disc ..................................... 10

Selecting the playback modes................ 11

Sound adjustments ................ 12

Selecting preset sound modes

(C-EQ: custom equalizer) .................. 12

Adjusting the sound ............................... 13

ENGLISH

General settings — PSM ......... 14

Basic procedure ..................................... 14

Detaching the control panel.... 15

Maintenance .......................... 16

More about this receiver ........ 17

Troubleshooting ..................... 18

Specifications ......................... 19

*For safety....

• Do not raise the volume level too much, as
this will block outside sounds, making driving
dangerous.

• Stop the car before performing any
complicated operations.

*Temperature inside the car....

If you have parked the car for a long time in
hot or cold weather, wait until the temperature
in the car becomes normal before operating the
unit.

3

How to read this manual

How to use the MODE button

The following methods are used to made the
explanations simple and easy-to-understand:

• Some related tips and notes are explained in

ENGLISH

“More about this receiver” (see page 17).

• Button operations are mainly explained with
the illustrations as follows:

Press briefly.

Press repeatedly.

If you press MODE, the receiver goes into
functions mode, then the number buttons work
as different function buttons.

Ex.: When number button 2 works as

MO (monaural) button.

Press either one.

Press and hold until
your desired response
begins.

Press and hold both
buttons at the same
time.

Time countdown indicator

To use these buttons for original functions
again after pressing MODE, wait for

5 seconds without pressing any of these buttons
until the functions mode is cleared.

• Pressing MODE again also clears the
functions mode.

4

Control panel — KD-G116/KD-G115

Parts identification

Display window

ENGLISH

1 +/– buttons
2 DISP (display) button
3 Loading slot
4 Display window
5 MODE button
6 0 (eject) button
7
8
9 SEL (select) button
p MO (monaural) button
q SSM (Strong-station Sequential Memory)

w CD button
e FM/AM button
r RPT (repeat) button
t RND (random) button
y EQ (equalizer) button
u
i Number buttons

¢/4 buttons

(standby/on/attenuator) button

button

(control panel release) button

Display window

o Tuner reception indicators

MO (monaural), ST (stereo)

; CD indicator
a RND
s RPT (repeat) indicator
d LOUD (loudness) indicator
f EQ (equalizer) indicator
g Sound mode (C-EQ: custom equalizer)

indicators
ROCK, CLASSIC, POPS, HIP HOP, JAZZ,
USER

•
indicator.

h Main display
j Source display

Volume level indicator

(disc random) indicator

also works as the time countdown

5

Getting started

ENGLISH

~

Basic operations

To drop the volume in a moment (ATT)

To restore the sound, press

it again.

Ÿ

You cannot select “CD” as the playback
source if there is no disc in the loading
slot.

!

Volume level appears.

Volume level indicator

To turn off the power

Caution on volume setting:

Discs produce very little noise compared
with other sources. Lower the volume
before playing a disc to avoid damaging
the speakers by the sudden increase of the
output level.

⁄ Adjust the sound as you want.

(See pages 12 and 13.)

6

Canceling the display

Setting the clock

demonstrations

If no operations are done for about 20 seconds,
display demonstration starts.

[Initial: DEMO ON]—see page 14.

1

2

3

1

2

Set the hour and minute.

1 Select “CLOCK H” (hour), then

adjust the hour.

2 Select “CLOCK M” (minute),

then adjust the minute.

3 Finish the procedure.

ENGLISH

Finish the procedure.

4

To activate the display demonstration

In step 3 above...

To check the current clock time when the
receiver is turned off

7

Radio operations

ENGLISH

~

Listening to the radio

2 Select the desired station frequencies.

Lights up when receiving an FM stereo
broadcast with sufficient signal strength.

Selected band appears.

Ÿ Start searching for a station.

When a station is received, searching
stops.
To stop searching, press the same
button again.

To tune in to a station manually

When an FM stereo broadcast is hard to
receive

1

2

Lights up when monaural mode is activated.

In step Ÿ above...
1

8

Reception improves, but stereo effect will
be lost.

To restore the stereo effect, repeat the same
procedure so that the MO indicator goes off.

Storing stations in memory

You can preset six stations for each band.

FM station automatic presetting —

SSM (Strong-station Sequential
Memory)

Select the FM band (FM1 – FM3)

1

you want to store into.

2

3

2

ENGLISH

3

Preset number flashes for a while.

“SSM” flashes, then disappears when
automatic presetting is over.

Local FM stations with the strongest signals are
searched and stored automatically in the FM
band.

Manual presetting

Ex.: Storing FM station of 92.5 MHz into the

preset number 4 of the FM1 band.

1

Listening to a preset station

1

2 Select the preset station (1 – 6) you

want.

To check the current clock time while
listening to an FM or AM station

9

Disc operations

ENGLISH

Playing a disc

All tracks will be played repeatedly until you
stop playback.

Total playing time of
the inserted disc

Elapsed playing
time

Total track number
of the inserted disc

Current track
number

To fast-forward or reverse the track

Fast-forwards.

Reverses.

To go to the next or previous tracks

To the following

tracks.

To the beginning of the current track, then

the previous tracks.

To go to a particular track directly

To select a number from 01 – 06:

To stop play and eject the disc

10

To select a number from 07 – 12:

Prohibiting disc ejection

You can lock a disc in the loading slot.

To cancel the prohibition, repeat the same
procedure.

To check the current clock time while
listening to a disc

Selecting the playback modes

You can use only one of the following playback modes at a time.

1

ENGLISH

2 Select your desired playback mode.

Repeat play

Ex.: When “TRK RPT” is selected

Random play

Ex.: When “DISC RND” is selected

Mode Plays repeatedly

TRK RPT: The current track.

• RPT lights up.

RPT OFF: Cancels repeat play.

Mode Plays at random

DISC RND: All tracks of the current disc.

• RND

RND OFF: Cancels random play.

lights up.

11

Sound adjustments

Selecting preset sound modes (C-EQ: custom equalizer)

ENGLISH

You can select a preset sound mode suitable to
the music genre.

~

Ex.: When “ROCK” is selected

Indication pattern for each sound mode:

Preset values

Indication For:

USER (Flat sound) 00 00 OFF

ROCK Rock or disco

music

CLASSIC Classical

music

POPS Light music +04 +01 OFF

HIP HOP Funk or rap

music

JAZZ Jazz music +02 +03 OFF

1

*

BAS: Bass

2

*

TRE: Treble

3

*

LOUD: Loudness

1

*

BAS

+03 +01 ON

+01 –02 OFF

+02 00 ON

TRE

*

2

LOUD

3

*

12

Adjusting the sound

You can adjust the sound characteristics to your
preference.

1

Ex.: When “TRE” is selected

2

Indication To do: Range

BAS*1
(bass)

1

TRE*
(treble)

2

FAD*
(fader)

BAL
(balance)

Adjust the bass. –06 (min.)

to
+06 (max.)

Adjust the treble. –06 (min.)

to
+06 (max.)

Adjust the front
and rear speaker
balance.

R06 (Rear
only)
to
F06 (Front
only)

Adjust the left
and right speaker
balance.

L06 (Left
only)
to
R06 (Right
only)

ENGLISH

Indication pattern changes
as you adjust the level.

LOUD*
(loudness)

1

Boost low and
high frequencies
to produce a well-

LOUD ON

J

LOUD OFF
balanced sound at
low volume level.

VOL*3
(volume)

Adjust the
volume.

00 (min.) to

30 or 50

(max.)*

*1 When you adjust the bass, treble, or

loudness, the adjustment you have made is
stored for the currently selected sound mode
(C-EQ) including “USER.”

2

*

If you are using a two-speaker system, set

the fader level to “00.”

3

*

Normally the +/– buttons work as the volume

control. So you do not have to select “VOL”
to adjust the volume level.

4

*

Depending on the amplifier gain control

setting. (See page 14 for details.)

4

13

General settings — PSM

Basic procedure

You can change PSM (Preferred Setting Mode)
items listed in the table that follows.

ENGLISH

1

Select a PSM item.

2

3 Adjust the PSM item selected.

4 Repeat steps 2 and 3 to adjust the

other PSM items if necessary.

5 Finish the procedure.

Ex.: When you select “AMP GAIN”

Indications Selectable settings, [reference page]

DEMO

Display demonstration

CLOCK H

Hour adjustment

CLOCK M

Minute adjustment

AMP GAIN

Amplifier gain control

DEMO ON: [Initial]; Display demonstration will be activated

automatically if no operation is done for about
20 seconds, [7].

DEMO OFF: Cancels.

1 – 12, [7]

[Initial: 1 (1:00)]

00 – 59, [7]

[Initial: 00 (1:00)]

You can change the maximum volume level of this receiver.
LOW PWR: VOL 00 – VOL 30 (Select this if the maximum power

of the speaker is less than 50 W to prevent them from
damaging the speaker.)

HIGH PWR: [Initial]; VOL 00 – VOL 50

14

Detaching the control panel

When detaching or attaching the control panel,
be careful not to damage the connectors on
the back of the control panel and on the panel
holder.

Detaching the control panel

Before detaching the control panel, be sure to
turn off the power.

Attaching the control panel

ENGLISH

15

Maintenance

How to clean the connectors

Frequent detachment will deteriorate the
connectors.
To minimize this possibility, periodically wipe

ENGLISH

the connectors with a cotton swab or cloth
moistened with alcohol, being careful not to
damage the connectors.

Connector

Moisture condensation

Moisture may condense on the lens inside the
CD player in the following cases:

• After starting the heater in the car.

• If it becomes very humid inside the car.
Should this occur, the CD player may
malfunction. In this case, eject the disc and
leave the receiver turned on for a few hours
until the moisture evaporates.

To keep discs clean

A dirty disc may not play correctly.
If a disc does become dirty, wipe
it with a soft cloth in a straight line
from center to edge.

• Do not use any solvent (for
example, conventional record cleaner, spray,
thinner, benzine, etc.) to clean discs.

To play new discs

New discs may have some rough
spots around the inner and outer
edges. If such a disc is used, this
receiver may reject the disc.
To remove these rough spots, rub the edges
with a pencil or ball-point pen, etc.

How to handle discs

When removing a disc from
its case, press down the center

holder of the case and lift the
disc out, holding it by the
edges.

• Always hold the disc by the edges. Do not
touch its recording surface.

When storing a disc into its case, gently insert
the disc around the center holder (with the
printed surface facing up).

• Make sure to store discs into the cases after
use.

Do not use the following discs:

Warped

disc

Center holder

Sticker

Sticker
residue

Disc

Stick-on
label

16

More about this receiver

Basic operations

Turning off the power

• If you turn off the power while listening to a
disc, disc play will start from where playback
has been stopped previously, next time you
turn on the power.

Tuner operations

Storing stations in memory

• During SSM search...

– All previously stored stations are erased and

stations are stored newly.

– Received stations are preset in No. 1 (lowest

frequency) to No. 6 (highest frequency).

– When SSM is over, the station stored in

No. 1 will be automatically tuned in.

• When storing a station manually, a previously
preset station is erased when a new station is
stored in the same preset number.

Disc operations

General

• Some CD-Rs or CD-RWs may not play
back on this receiver because of their disc
characteristics, and for the following causes:

– Discs are dirty or scratched.
– Moisture condensation occurs on the lens

inside the receiver.
– The pickup lens inside the receiver is dirty.
– CD-R or CD-RW on which the files are

written with “Packet Write” method.
– There are improper recording conditions

(missing data, etc.) or media conditions

(stain, scratch, warp, etc.).

• CD-RWs may require a longer readout time

since the reflectance of CD-RWs is lower
than that of regular CDs.

• Do not use the following CD-Rs or

CD-RWs:

– Discs with stickers, labels, or protective seal

stuck to the surface.
– Discs on which labels can be directly

printed by an ink jet printer.
Using these discs under high temperatures

or high humidity may cause malfunctions or
damage to discs.

ENGLISH

• This receiver has been designed to reproduce
CDs, and CD-Rs (Recordable)/ CD-RWs
(Rewritable) in audio CD (CD-DA) format.

• When a disc has been loaded, selecting “CD”
for the playback source starts disc play.

Inserting a disc

• When a disc is inserted upside down, the disc
automatically ejects.

• Do not insert 8 cm discs (single CD) and
unusual shape discs (heart, flower, etc.) into
the loading slot.

Playing a CD-R or CD-RW

• Use only “finalized” CD-Rs or CD-RWs.

• This receiver can play back multi-session
discs; however, unclosed sessions will be
skipped while playing.

Changing the source

• If you change the source, playback also stops
(without ejecting the disc).

Next time you select “CD” for the playback

source, disc play starts from where it has been
stopped previously.

Ejecting a disc

• If the ejected disc is not removed within
15 seconds, the disc is automatically inserted
again into the loading slot to prevent it from
dust. (Disc will not play this time.)

General settings—PSM

• If you change the “AMP GAIN” setting from
“HIGH PWR” to “LOW PWR” while the
volume level is set higher than “VOL 30,” the
receiver automatically changes the volume
level to “VOL 30.”

17

Troubleshooting

What appears to be trouble is not always serious. Check the following points before calling a service
center.

Symptoms Causes Remedies

ENGLISH

• Sound cannot be heard
from the speakers.

General

• The receiver does not
work at all.

The volume level is set to
the minimum level.

Connections are incorrect. Check the cords and

The built-in microcomputer
may have functioned
incorrectly due to noise, etc.

Adjust it to the optimum
level.

connections.

Reset the receiver (see page

2).

• SSM automatic presetting
does not work.

• Static noise while listening

FM/AM

to the radio.

• Disc automatically ejects. Disc is inserted upside

• CD-R/CD-RW cannot be
played back.

• Tracks on the CD-R/
CD-RW cannot be
skipped.

• Disc can be neither played
back nor ejected.

Disc playback

• Disc sound is sometimes
interrupted.

Signals are too weak. Store stations manually.

The antenna is not connected
firmly.

down.

CD-R/CD-RW is not
finalized.

Disc is locked. Unlock the disc (see page

The CD player may have
functioned incorrectly.

You are driving on rough
roads.

Connect the antenna firmly.

Insert the disc correctly.

• Insert a finalized CD-R/
CD-RW.

• Finalize the CD-R/
CD-RW with the
component which you
used for recording.

11).

Eject the disc forcibly (see
page 2).

Stop playback while driving
on rough roads.

• “NO DISC” appears on the
display.

18

Disc is scratched. Change the disc.

Connections are incorrect. Check the cords and

connections.

No disc is in the loading
slot.

Disc is inserted incorrectly. Insert the disc correctly.

Insert a disc into the loading
slot.

Specifications

AUDIO AMPLIFIER SECTION

Maximum Power Output:
Front: 50 W per channel
Rear: 50 W per channel
Continuous Power Output (RMS):
Front: 19 W per channel into 4 Ω, 40 Hz

to 20 000 Hz at no more than 0.8%
total harmonic distortion.

Rear: 19 W per channel into 4 Ω, 40 Hz

to 20 000 Hz at no more than 0.8%
total harmonic distortion.

Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)
Tone Control Range:

Bass: ±10 dB at 100 Hz
Treble: ±10 dB at 10 kHz
Frequency Response: 40 Hz to 20 000 Hz
Signal-to-Noise Ratio: 70 dB
Line-Out Level/Impedance:

2.0 V/20 kΩ load (full scale)

Output Impedance: 1 kΩ

TUNER SECTION

Frequency Range:
FM: 87.5 MHz to 108.0 MHz
AM: 531 kHz to 1 602 kHz

CD PLAYER SECTION

Type: Compact disc player
Signal Detection System: Non-contact optical

pickup (semiconductor laser)
Number of channels: 2 channels (stereo)
Frequency Response: 5 Hz to 20 000 Hz
Dynamic Range: 96 dB
Signal-to-Noise Ratio: 98 dB
Wow and Flutter: Less than measurable limit

GENERAL

Power Requirement:
Operating Voltage:

DC 14.4 V (11 V to 16 V allowance)
Grounding System: Negative ground
Allowable Operating Temperature:

0°C to +40°C
Dimensions (W × H × D):
Installation Size (approx.):

182 mm × 52 mm × 150 mm
Panel Size (approx.):

188 mm × 58 mm × 11 mm
Mass (approx.):

1.3 kg (excluding accessories)

ENGLISH

[FM Tuner]

Usable Sensitivity: 11.3 dBf (1.0 µV/75 Ω)
50 dB Quieting Sensitivity:

16.3 dBf (1.8 µV/75 Ω)
Alternate Channel Selectivity (400 kHz): 65 dB
Frequency Response: 40 Hz to 15 000 Hz
Stereo Separation: 35 dB
Capture Ratio: 1.5 dB

[AM Tuner]

Sensitivity: 20 µV
Selectivity: 35 dB

Having TROUBLE with operation?

Please reset your unit

Design and specifications are subject to change
without notice.

Refer to page of How to reset your unit

19

EN, TH

© 2004 Victor Company of Japan, Limited

1004DTSMDTJEIN

KD-G116/KD-G115

Installation/Connection Manual

°“√µ‘¥µ—Èß/§ŸË¡◊Õ°“√µ‘¥µ—Èß

GET0252-004A

[U/UH]

1004DTSMDTJEIN
EN, TH

ENGLISH

This receiver is designed to operate on 12 V DC, NEGATIVE ground elect rical systems. If
your vehicle does not have this system, a voltage inverter is required, which can be purchased
at JVC car audio dealers.

‰∑¬

™ÿ¥ª√–°Õ∫π’ȉ¥È√—∫°“√ÕÕ°·∫∫¡“‡æ◊ËÕ„™Èß“π°—∫√–∫∫ °√–·‰øøÈ““¬¥‘π¢—È«≈∫°√–·µ√ß 12 ‚«≈∑Ï À“°√∂¬πµÏ¢Õߧÿ≥‰¡Ë ‰
¥È„™È√–∫∫π’È µÈÕß„™È‡§√◊ËÕß·ª≈ß°√–·‰ø™Ë«¬ ´÷Ëß“¡“√∂À“´◊ÈÕ‰¥È®“°√È“π¢“¬‡§√◊ËÕ߇’¬ß√∂¬πµÏ JVC

J

Handles

§—π∫—ߧ—∫

F

Washer (ø5)

ª√–‡°Áπ«ß·À«π (ø5)

G

Lock nut (M5)

πÕµ≈ÁÕ§ (M5)

H

Mounting bolt (M5 x 20 mm)

≈—°µ‘¥ (M5 x 20 ¡‘≈≈‘‡¡µ√)

I

Rubber cushion

¬“ß°—π°√–·∑°

A / B
Hard case/Control panel

≈—ß∫√√®ÿ/ÀπÈ“ª—¥

D

Trim plate

·ºËπ‚≈À–¢Õ∫·µËß

E

Power cord

“¬‡§‡∫‘≈°”≈—ß

Parts list for installation and connection

The following parts are provided for this receiver.
After checking them, please set them correctly.

√“¬°“√Ë«πª√–°Õ∫”À√—∫µ‘¥µ—Èß·≈–‡™◊ËÕ¡µËÕ°—π
«πª√–°Õ∫µËÕ‰ªπ’È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È À≈—ß®“°µ√«®Õ∫·≈È« ª√—∫µ—È߇§√◊ËÕß„ÀÈ∂Ÿ°µÈÕß

1

INSTALLATION (IN-DASH MOUNTING)

The following illustration shows a typical installation. If you have any questions or require
information regarding installation kits, consult your JVC car audio dealer or a company supplying
kits.

• If you are not sure how to install this receiver correctly, have it installed by a qualified
technician.

°“√µ‘¥µ—Èß (°“√ª√–°Õ∫·ºßÀπÈ“ª—∑¡Ï‡¢È“)

¿“æµ—«Õ¬Ë“ßµËÕ‰ªπ’È·¥ß∂÷ß°“√µ‘¥µ—Èß·∫∫∑—Ë«‰ª À“°§ÿ≥¡’ª—≠À“À√◊ÕµÈÕß°“√¢ÈÕ¡Ÿ≈‡°’ˬ«°—∫™ÿ¥µ‘¥µ—Èß °√ÿ≥“ª√÷°…“°—∫ºŸÈ¢“¬‡§√◊ËÕ߇’
¬ß√∂¬πµÏ JVC ¢Õß∑Ë“πÀ√◊Õ∫√‘…—

•

™ÿ¥ª√–°Õ∫ ∂È“§ÿ≥‰¡Ë·πË„®«Ë“µ‘¥µ—Èß™ÿ¥ª√–°Õ∫π’È∂Ÿ°µÈÕßÀ√◊Õ‰¡Ë „ÀÈÀ“™Ë“ߺŸÈ‡™’ˬ«™“≠‡ªÁπºŸÈµ‘¥µ—Èß

Do the required electrical connections.

µËÕ“¬‰øµ“¡∑’Ë°”À𥉫È∑—ÈßÀ¡¥

*1 When you stand the receiver, be

careful not to damage the fuse on
the rear.

*1 ‡¡◊ËÕ§ÿ≥µ—Èß™ÿ¥ª√–°Õ∫¢÷Èπ √–«—ßլ˓∑”„ÀÈø‘«Ï∫√‘‡«≥

Ë«π∑È“¬‡’¬À“¬

Bend the appropriate tabs to hold the
sleeve firmly in place.

ßÕ·ºËπ‡æ◊ËÕ¬÷¥ª≈Õ°„ÀȵËÕ°—π‡¢È“∑’Ë

Removing the receiver

Before removing the receiver, release the rear section.

When installing the receiver without using the sleeve /

‡¡◊ËÕµ‘¥µ—Èß™ÿ¥ª√–°Õ∫‚¥¬‰¡Ë„™Èª≈Õ°ÀÿÈ¡

In a Toyota for example, first remove the car radio and install the receiver in its place.

µ—«Õ¬Ë“߇™Ëπ „π√∂¬πµÏ‚µ‚¬µÈ“ „ÀÈ∂Õ¥«‘∑¬ÿµ‘¥√∂¬πµÏÕÕ°°ËÕπ·≈–µ‘¥µ—Èß™ÿ¥ª√–°Õ∫π’ȇ¢È“‰ª·∑π

When using the optional stay /

‡¡◊ËÕ„™Èµ—«¬÷¥·∫∫‡≈◊Õ°‰¥È

Note : When installing the receiver on the mounting bracket, make sure to use the 8 mm-long screws. If

longer screws are used, they could damage the receiver.

À¡“¬‡Àµ : ‡¡◊ËÕµ‘¥µ—Èß™ÿ¥ª√–°Õ∫≈ß„π·∑Ëπ√Õß√—∫‰«È „ÀÈ„™È°√Ÿ¬“«¢π“¥ 8 ¡‘≈≈‘‡¡µ√ ∂È“„™È°√Ÿ¬“«°«Ë“π’ÈÕ“®∑”„ÀÈ™ÿ¥ª√–°Õ∫‡’¬À“¬‰¥ô

Bracket*

·∑Ëπ√Õß√—∫*

Bracket*

·∑Ëπ√Õß√—∫*

*

Not included for this receiver.

*

‰¡Ë‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π

Flat type screws
(M5 x 8 mm)*

°√ŸÀ—«‡√’¬∫
(M5 x 8 ¡‘≈≈‘‡¡µ√)*

Pocket

°–‡ª“–

Flat type screws
(M5 x 8 mm)*

°√ŸÀ—«‡√’¬∫

(M5 x 8 ¡‘≈≈‘‡¡µ√)*

Screw (option)

°√Ÿ (‡≈◊Õ°‰¥È)

Stay (option)

µ—«¬÷¥ (‡≈◊Õ°‰¥È)

Fire wall

ºπ—ß°—π‰ø

Dashboard

·ºßÀπÈ“ª—∑¡á

Install the receiver at an angle of less than 30˚.

µ‘¥µ—Èß™ÿ¥ª√–°Õ∫∑’Ë¡ÿ¡µË”°«Ë“ 30 Õß»“

TROUBLESHOOTING

• The fuse blows.

* Are the red and black leads connected correctly?

• Power cannot be turned on.

* Is the yellow lead connected?

• No sound from the speakers.

* Is the speaker output lead short-circuited?

• Sound is distor ted.

* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?

• Noise inter fere with sounds.

* Is the rear ground terminal connected to the car ʼs chassis using shorter and thicker cords?

• Receiver b ecomes hot.

* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?

• This receiver does not work at all.

* Have you reset your receiver?

°“√µ√«®Õ∫ª—≠À“¢—¥¢ÈÕß

• ø‘«Ï¢“¥
* ¡’°“√‡™◊ËÕ¡ “¬µ–°—Ë«’¥”·≈–’·¥ßլ˓ß∂Ÿ°µÈÕßÀ√◊Õ‰¡Ë

• ‰¡Ë“¡“√∂‡ª‘¥‡§√◊ËÕ߉¥È
* ¡’°“√‡™◊ËÕ¡“¬µ–°—Ë«’‡À≈◊ÕßÀ√◊Õ‰¡Ë

• ‰¡Ë¡’‡’¬ßÕÕ°®“°≈”‚æß
* “¬µ–°—Ë««π∑’ËÕÕ°∑“ß≈”‚æ߇°‘¥‰øøÈ“≈—¥«ß®√À√◊Õ‰¡Ë

• ‡’¬ß‡æ’Ȭπ
* “¬µ–°—Ë««π∑’ËÕÕ°∑“ß≈”‚æßµËÕ≈ߥ‘πÀ√◊Õ‰¡Ë
* “¬¢—È«≈∫ “–” ¢Õß≈”‚æߥȓπ´È“¬·≈–¢«“µËÕ≈ߥ‘πµ“¡ª°µ‘À√◊Õ‰¡Ë

• ‡’¬ß√∫°«π
* ¡’°“√„™È“¬—ÈπÊ À√◊ÕÀπ“Ê µËÕ®“°‡§√◊ËÕß«π∑’˵‘¥µ—Èß ‰«È∫πæ◊Èπ¥È“πÀ≈—ß°—∫µ—«∂—ß√∂¬πµÏÀ√◊Õ‰¡Ë

• ™ÿ¥ª√–°Õ∫√ÈÕπ¢÷Èπ
* “¬µ–°—Ë«Ë«π∑’ËÕÕ°∑“ß≈”‚æßµËÕ≈ߥ‘πÀ√◊Õ‰¡Ë
* “¬¢—È«≈∫ “–” ¢Õß≈”‚æߥȓπ´È“¬·≈–¢«“µËÕ≈ߥ‘πµ“¡ª°µ‘À√◊Õ‰¡Ë

• ‡§√◊ËÕß√—∫π’È∑”ß“π‰¡
* ∑Ë“π‰¥Èµ—È߇§√◊ËÕß„À¡Ë·≈È«À√◊Õ¬—ß

C

Sleeve

ª≈Õ°ÀÿÈ¡

°“√∂Õ¥™ÿ¥ª√–°Õ∫

°ËÕπ®–∂Õ¥™ÿ¥ª√–°Õ∫ „ÀȪ≈¥ÀπÈ“µ—¥Ë«π∑È“¬°ËÕπ

Insert the two handles, then pull them as illustrated so
that the receiver can be removed.

„˧—π∫—ߧ—∫ 2 Õ—π≈ß„π√ËÕß”À√—∫„™Èæ—π≈«¥ ¥—ß¿“æ ®“°π—Èπ „Àȇ≈◊ËÕπ™ÿ¥ª√–
°Õ∫ÕÕ° „π¢≥–∑’˧ËÕ¬ Ê ¥÷ߧ—π∫—ߧ—∫∑—Èß

Õß Õ—πÕÕ°®“°°—π

ELECTRICAL CONNECTIONS

To prevent short circuits, we recommend that you disconnect the batteryʼs negative terminal and
make all electrical connections before installing the receiver.

• Be sure to ground this receiver to the car’s chassis again af ter installat ion.

Notes:

• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC
car audio dealer.

• It is recommended to connect to the speakers with maximum power of more than 50 W (both
at the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less
than 50 W, change “AMP GAIN” setting to prevent the speakers
from being damaged (see page 14 of the INSTRUCTIONS).

• To prevent short-circuit, cover the terminals of the UNUSED
leads with insulating tape.

• The heat sink becomes very hot after use. Be
careful not to touch it when removing this receiver.

°“√‡™◊ËÕ¡‚¥¬„™È‰øøÈ“

‡æ◊ËÕªÈÕß°—π°“√‡°‘¥‰øøÈ“≈—¥«ß®√ ¢Õ·π–π”„ÀȪ≈¥¢—È«·∫µ‡µÕ√’Ë≈∫ÕÕ° ·≈È«®÷ßµËÕ“¬‰ø°ËÕ𵑥µ—È߇§√◊ËÕß

• µ√«®Õ∫„ÀÈ·πË„®«Ë“‰¥È‡¥‘π“¬¥‘πµËÕ√–À«Ë“߇§√◊ËÕß°—∫µ—«∂—ß √∂¬πµÏ„À¡Ë·≈È«À≈—ß®“°µ‘¥µ—Èß

À¡“¬‡Àµÿ:

• „™Èæ‘°—¥®”‡æ“–·∑πø‘« À“°ø‘«Ï¢“¥∫ËÕ¬ „ÀȪ√÷°…“√È“ π¢“¬‡§√◊ËÕ߇’¬ß√∂¬πµÏ JVC

• ¢Õ·π–π”„ÀȵËÕ≈”‚æß ∑’Ë¡’°”≈—ߢ—∫ßÿ¥‡°‘π°«Ë“ 50 W (∑—ÈߥȓπÀπÈ“·≈–¥È“πÀ≈—ß ¡’§Ë“§«“¡µÈ“π∑“π 4 Ω ∂÷ß 8 Ω)

∂È“°”≈—ߢ—∫µË”°«Ë“ 50 W „Àȇª≈’ˬπ§Ë“ “AMP GAIN” ‡æ◊ËÕªÈÕß°—π‰¡Ë„ÀÈ≈”‚æß™”√ÿ¥ (¥ŸÀπÈ“ 14 §”·π–π”)

• °“√ªÈÕß°—π°“√≈—¥«ß®√ ®–µÈÕßæ—π¢—È«“¬µ–°—Ë« ∑’ˉ¡Ë„™È·≈È«¥È«¬‡∑ ªæ—π“¬‰ø

• ·ºËπ√–∫“¬§«“¡√ÈÕπ®–√ÈÕπ¡“°À≈—ß®“°„™È √–¡—¥√–«—ßլ˓‰ª —¡º—‡¡◊ËÕ∂Õ¥™ÿ¥ª√–°Õ∫π’È

Heat sink

·ºËπ√–∫“¬§«“¡√ÈÕπ

2

ENGLISH

‰∑¬

A

Typical connections / °“√‡™◊ËÕ¡µËÕ·∫∫ª°µ‘

Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause
serious damage to this receiver.
The leads of the power cord and those of the connector from the car body may be different in
color.

1 Connect the colored leads of the power cord in the order specified in the illustration below.
2 Connect the antenna cord.
3 Finally connect the wiring harness to the receiver.

°ËÕ•∑”°“•‡™•ËÕ¡µËÕ: µ•«®†Õ•°“•‡¥‘•†“¬‰ø„•••¬•µÏլ˓ߕ–¡—¥•–«—լ˓„ÀȺ‘¥æ•“¥„•°“•‡™•ËÕ¡µËÕ™ÿ¥ª•–°Õ•™ÿ¥•’
°“•‡™•ËÕ¡µËÕº‘¥æ•“¥Õ“®∑”„Àȇ°‘¥§«“¡‡†’¬À“¬•È“¬·•ß°—•™ÿ¥ª•–
°Õ••’ȉ¥È“•µ–°—Ë«¢Õ߆“¬‰ø ·•–¢ÕßÕÿª°••ÏµËÕ‡™•ËÕ¡®“°µ—«• ß••Õ“®¡’†’∑’ˉ¡Ë‡À¡•Õ•°—•

1 µËÕ“¬‰ø’µ“¡≈”¥—∫∑’Ë√–∫ÿ„π√Ÿª¥È“π≈Ë“ß
2 ‡™◊ËÕ¡µËÕ°—∫“¬Õ“°“»
3 ÿ¥∑È“¬ µËÕË«π§«∫§ÿ¡°“√‡¥‘π“¬‰ø‡¢È“°—∫™ÿ¥ª√–°Õ∫™ÿ¥π’È

B

Connecting the external amplifier / °“√µËÕ‡æ‘Ë¡‡µ‘¡‡¢È“°—∫Õÿª°√≥ÏÕ◊Ëπ

You can connect an amplifier to upgrade your car stereo system.

• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so
that it can be controlled through this receiver.

• Disconnect the speaker s from this receive r, connect them to the amplifier. Leave the

speaker leads of this receiver unused.

§ÿ≥“¡“√∂µËÕ°—∫·Õ¡æ≈‘ø“¬‡ÕÕ√Ï ‡æ◊ËÕ‡æ‘Ë¡§ÿ≥ ¿“æ‡’¬ß„ÀÈ°—∫√–∫∫‡µÕ√‘‚Õ¢Õß√∂¬πµÏ

• µËÕ“¬µ–°—Ë«√–¬–‰°≈ (’πÈ”‡ß‘π≈“¬¢“«) ‡¢È“°—∫“¬µ–°—Ë«√–¬–‰°≈¢ÕßÕÿª°√≥ÏÕ◊Ëπ Ê ‡æ◊ËÕ®–“¡“√∂§«∫§ÿ¡‚¥¬™ÿ¥ª√–
°Õ∫π’ȉ¥È

• ∂Õ¥≈”‚æßÕÕ°®“°™ÿ¥ª√–°Õ∫π’È ·≈È«µËÕ‡¢È“°—∫‡§√◊ËÕߢ¬“¬ ∑‘Èß“¬µ–°—Ë«≈”‚æߢÕß™ÿ¥ª√–°Õ∫π’ȉ«È

Signal cord (not supplied for this receiver)

“¬‡§‡∫‘≈—≠≠“≥ (‰¡Ë‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È)

Front speakers

≈”‚æßÀπÈ“

Rear speakers

≈”‚æßÀ≈—ß

JVC Amplifier

‡§√◊ËÕߢ¬“¬‡’¬ß JVC

KD-G116
KD-G115

Remote lead

“¬µ–°—Ë«•–¬–‰°•

Y-connector (not supplied for this receiver)

¢ÈÕµËÕ√Ÿªµ—« Y (‰¡Ë‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È)

Remote lead (Blue with white stripe)

“¬µ–°—Ë«•–¬–‰°• (’πÈ”‡ß‘π≈“¬¢“«)

To the remote lead of other equipment or automatic antenna if any

µËÕ“¬°—∫Õÿª°√≥ÏÕ◊ËπÀ√◊Õ‡“Õ“°“»Õ—µ‚π¡—µ‘∂È“¡’

*2 Before checking the operation of this receiver

prior to installation, this lead must be connected,
otherwise power cannot be turned on.

*2

°ËÕπ°“√µ√«®Õ∫°“√∑”ß“π¢Õß™ÿ¥ª√–°Õ∫π’È°ËÕπ∑’Ë®–µ‘¥µ—Èß
µÈÕßµËÕ“¬µ–°—Ë«π’È°ËÕπ ¡‘©–π—Èπ®–‰¡“¡“√∂‡ª‘¥‡§√◊ËÕ߉¥

Line out (see diagram )

“¬ÕÕ° (¥Ÿ·ºπ¿Ÿ¡ )

Rear ground
terminal

®ÿ¥‡™◊ËÕ¡µËÕ
“¬¥‘π¥È“πÀ≈—ß

15 A fuse

ø‘«Ï¢π“¥ 15 A

Antenna terminal

¢—È«“¬Õ“°“»

Black

’¥”

Blue with white stripe

’πÈ”‡ß‘π≈“¬¢“«

Red

’·¥ß

Yellow*

2

’‡À≈◊Õß*

2

*1 Not included for this receiver

*

1

‰¡Ë‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π

To metallic body or chassis of the car

µËÕ°—∫‚§√ß‚≈À–À√◊Õ‡™´‘¢Õß√∂¬πµÏ

To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)

µËÕ°—∫¢—È«∑’Ë¡’°√–·‰øøÈ“„π·ºßø‘«Ï ´÷ËßµËÕ°—∫·∫µ‡µÕ√’Ë√∂¬πµ
(‚¥¬‰¡ËµÈÕß„™È«‘∑™Ï®ÿ¥√–‡∫‘¥) (12 ‚«≈∑ϧß∑’Ë)

Ignition switch

«‘∑™Ï®ÿ¥√–‡∫‘¥

Fuse block

·ºßø‘«

To an accessory terminal in the fuse block

µËÕ°—∫¢—È«Ë«πª√–°Õ∫„π·ºßø‘«

To the automatic antenna if any (250 mA max.)

‡“Õ“°“»‰øøÈ“Õ—µ‚π¡—µ‘ À“°¡’ (¢π“¥Ÿß¸¥ 250 mA )

Left speaker (front)

≈”‚æß´È“¬ (ÀπÈ“)

Right speaker (front)

≈”‚æߢ«“ (ÀπÈ“)

Left speaker (rear)

≈”‚æß´È“¬ (À≈—ß)

Right speaker (rear)

≈”‚æߢ«“ (À≈—ß)

Purple

’¡Ë«ß

Purple with black stripe

’¡Ë«ß·∂∫¥”

Green

’‡¢’¬«

Gray

’‡∑“

Gray with black stripe

’‡∑“·∂∫¥”

White

’¢“«

White with black
stripe

’¢“«·∂∫¥”

*3 Firmly attach the ground wire to

the metallic body or to the chassis
of the car—to the place not coated
with paint (if coated with paint,
remove the paint before attaching
the wire). Failure to do so may
cause damage to the receiver.

*3

µËÕ≈«¥“¬¥‘π„ÀÈ·πËπ‡¢È“°—∫µ—«∂—߇À≈Á°
À√◊Õµ—«∂—ß√∂—µ√ßË«π ∑’ˉ¡Ë¡’’‡§≈◊Õ∫
(À“°¡’’‡§≈◊Õ∫Õ¬ŸË „ÀÈ¢Ÿ¥’ÕÕ°°ËÕπ
°ËÕπµËÕ≈«¥“¬¥‘π) À“°‰¡ËªØ‘∫—µ‘µ“¡§”·π–
π”π’È ‡§√◊ËÕßÕ“®™”√ÿ¥À√◊Õ‡’¬À“¬‰¥

PRECAUTIONS on power supply and speaker connections:

• DO NOT connect the speaker l eads of the power cord to

the car battery; other wise, the rec eiver will be seriously
damaged.

• BEFORE connecting the speaker leads of the power cord to the
speakers, check the speaker wiring in your car.

¢ÈÕ§«√√–«—ß”À√—∫°“√µËÕ·À≈Ë߮˓¬°”≈—ß·≈–≈”‚æß:

•

լ˓µËÕ“¬µ–°—Ë«‡§‡∫‘≈°”≈—ߢÕß≈”‚æ߇¢È“°—∫·∫µ‡µÕ√’Ë√∂¬πµÏ ¡‘©–π—Èπ ™ÿ¥ª√–°Õ∫®–‰¥È√—
∫§«“¡‡’¬À“¬¡“°

• °ËÕπ∑’Ë®–µËÕ“¬µ–°—Ë«‡§‡∫‘≈°”≈—ߢÕß≈”‚æ߇¢È“°—∫≈”‚æß „Àȵ√«®Õ∫°“√‡¥‘π“¬‰ø≈”‚æ
ß„π√∂¢Õߧÿ≥„Àȇ√’¬∫√ÈÕ¬‡’¬°ËÕπ

To the remote lead of other equipment (200 mA max.)

µËÕ‡¢È“°—∫Õª°√≥ÏÕË◊π (¢π“¥Ÿß¸¥ 200 mA

)

Blue

»’øÈ“

Green with black stripe

’‡¢’¬«·∂∫¥”

CD RECEIVER KD-G116/KD-G115

ENGLISH

ALAT PENERIMA CD KD-G116/KD-G115

For canceling the display demonstration, see page 7.
Untuk membatalkan tampilan demonstrasi, lihat halaman 7.

INDONESIA

For installation and connections, refer to the separate manual.
Untuk instalasi dan penyambungan, lihat buku pedoman terpisah.

INSTRUCTIONS

BUKU PETUNJUK

GET0252-003A

[UN]

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and to

obtain the best possible performance from the unit.

ENGLISH

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave

all servicing to qualified service personnel.

3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated.

Avoid direct exposure to beam.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

Warning:

If you need to operate the receiver while
driving, be sure to look ahead carefully or
you may be involved in a traffic accident.

How to forcibly eject a disc

If a disc cannot be recognized by the
receiver or cannot be ejected, ejects the disc
as follows.

How to reset your unit

• This will reset the microcomputer. Your
preset adjustments will also be erased.

• If a disc is loaded, it will eject. Be careful
not to drop the disc.

• If this does not work, try to reset your
receiver.

• Be careful not to drop the disc when it
ejects.

2

Contents

How to reset your unit ........................... 2

How to forcibly eject a disc................... 2

How to read this manual........................ 4

How to use the MODE button ............... 4

Control panel

— KD-G116/KD-G115 ............... 5

Parts identification................................. 5

Getting started....................... 6

Basic operations ........................... 6

Canceling the display demonstrations ... 7

Setting the clock .................................... 7

Radio operations ................... 8

Listening to the radio........................... 8

Storing stations in memory.................... 9

Listening to a preset station ................... 9

Disc operations ...................... 10

Playing a disc ..................................... 10

Selecting the playback modes................ 11

Sound adjustments ................ 12

Selecting preset sound modes

(C-EQ: custom equalizer) .................. 12

Adjusting the sound ............................... 13

ENGLISH

General settings — PSM ......... 14

Basic procedure ..................................... 14

Detaching the control panel.... 15

Maintenance .......................... 16

More about this receiver ........ 17

Troubleshooting ..................... 18

Specifications ......................... 19

*For safety....

• Do not raise the volume level too much, as
this will block outside sounds, making driving
dangerous.

• Stop the car before performing any
complicated operations.

*Temperature inside the car....

If you have parked the car for a long time in
hot or cold weather, wait until the temperature
in the car becomes normal before operating the
unit.

3

How to read this manual

How to use the MODE button

The following methods are used to made the
explanations simple and easy-to-understand:

• Some related tips and notes are explained in

ENGLISH

“More about this receiver” (see page 17).

• Button operations are mainly explained with
the illustrations as follows:

Press briefly.

Press repeatedly.

If you press MODE, the receiver goes into
functions mode, then the number buttons work
as different function buttons.

Ex.: When number button 2 works as

MO (monaural) button.

Press either one.

Press and hold until
your desired response
begins.

Press and hold both
buttons at the same
time.

Time countdown indicator

To use these buttons for original functions
again after pressing MODE, wait for

5 seconds without pressing any of these buttons
until the functions mode is cleared.

• Pressing MODE again also clears the
functions mode.

4

Control panel — KD-G116/KD-G115

Parts identification

Display window

ENGLISH

1 +/– buttons
2 DISP (display) button
3 Loading slot
4 Display window
5 MODE button
6 0 (eject) button
7
8
9 SEL (select) button
p MO (monaural) button
q SSM (Strong-station Sequential Memory)

w CD button
e FM/AM button
r RPT (repeat) button
t RND (random) button
y EQ (equalizer) button
u
i Number buttons

¢/4 buttons

(standby/on/attenuator) button

button

(control panel release) button

Display window

o Tuner reception indicators

MO (monaural), ST (stereo)

; CD indicator
a RND
s RPT (repeat) indicator
d LOUD (loudness) indicator
f EQ (equalizer) indicator
g Sound mode (C-EQ: custom equalizer)

indicators
ROCK, CLASSIC, POPS, HIP HOP, JAZZ,
USER

•
indicator.

h Main display
j Source display

Volume level indicator

(disc random) indicator

also works as the time countdown

5

Getting started

ENGLISH

~

Basic operations

To drop the volume in a moment (ATT)

To restore the sound, press

it again.

Ÿ

You cannot select “CD” as the playback
source if there is no disc in the loading
slot.

!

Volume level appears.

Volume level indicator

To turn off the power

Caution on volume setting:

Discs produce very little noise compared
with other sources. Lower the volume
before playing a disc to avoid damaging
the speakers by the sudden increase of the
output level.

⁄ Adjust the sound as you want.

(See pages 12 and 13.)

6

Canceling the display

Setting the clock

demonstrations

If no operations are done for about 20 seconds,
display demonstration starts.

[Initial: DEMO ON]—see page 14.

1

2

3

1

2

Set the hour and minute.

1 Select “CLOCK H” (hour), then

adjust the hour.

2 Select “CLOCK M” (minute),

then adjust the minute.

3 Finish the procedure.

ENGLISH

Finish the procedure.

4

To activate the display demonstration

In step 3 above...

To check the current clock time when the
receiver is turned off

7

Radio operations

ENGLISH

~

Listening to the radio

2 Select the desired station frequencies.

Lights up when receiving an FM stereo
broadcast with sufficient signal strength.

Selected band appears.

Ÿ Start searching for a station.

When a station is received, searching
stops.
To stop searching, press the same
button again.

To tune in to a station manually

When an FM stereo broadcast is hard to
receive

1

2

Lights up when monaural mode is activated.

In step Ÿ above...
1

8

Reception improves, but stereo effect will
be lost.

To restore the stereo effect, repeat the same
procedure so that the MO indicator goes off.

Storing stations in memory

You can preset six stations for each band.

FM station automatic presetting —

SSM (Strong-station Sequential
Memory)

Select the FM band (FM1 – FM3)

1

you want to store into.

2

3

2

ENGLISH

3

Preset number flashes for a while.

“SSM” flashes, then disappears when
automatic presetting is over.

Local FM stations with the strongest signals are
searched and stored automatically in the FM
band.

Manual presetting

Ex.: Storing FM station of 92.5 MHz into the

preset number 4 of the FM1 band.

1

Listening to a preset station

1

2 Select the preset station (1 – 6) you

want.

To check the current clock time while
listening to an FM or AM station

9

Disc operations

ENGLISH

Playing a disc

All tracks will be played repeatedly until you
stop playback.

Total playing time of
the inserted disc

Elapsed playing
time

Total track number
of the inserted disc

Current track
number

To fast-forward or reverse the track

Fast-forwards.

Reverses.

To go to the next or previous tracks

To the following

tracks.

To the beginning of the current track, then

the previous tracks.

To go to a particular track directly

To select a number from 01 – 06:

To stop play and eject the disc

10

To select a number from 07 – 12:

Prohibiting disc ejection

You can lock a disc in the loading slot.

To cancel the prohibition, repeat the same
procedure.

To check the current clock time while
listening to a disc

Selecting the playback modes

You can use only one of the following playback modes at a time.

1

ENGLISH

2 Select your desired playback mode.

Repeat play

Ex.: When “TRK RPT” is selected

Random play

Ex.: When “DISC RND” is selected

Mode Plays repeatedly

TRK RPT: The current track.

• RPT lights up.

RPT OFF: Cancels repeat play.

Mode Plays at random

DISC RND: All tracks of the current disc.

• RND

RND OFF: Cancels random play.

lights up.

11

Sound adjustments

Selecting preset sound modes (C-EQ: custom equalizer)

ENGLISH

You can select a preset sound mode suitable to
the music genre.

~

Ex.: When “ROCK” is selected

Indication pattern for each sound mode:

Preset values

Indication For:

USER (Flat sound) 00 00 OFF

ROCK Rock or disco

music

CLASSIC Classical

music

POPS Light music +04 +01 OFF

HIP HOP Funk or rap

music

JAZZ Jazz music +02 +03 OFF

1

*

BAS: Bass

2

*

TRE: Treble

3

*

LOUD: Loudness

1

*

BAS

+03 +01 ON

+01 –02 OFF

+02 00 ON

TRE

*

2

LOUD

3

*

12

Adjusting the sound

You can adjust the sound characteristics to your
preference.

1

Ex.: When “TRE” is selected

2

Indication To do: Range

BAS*1
(bass)

1

TRE*
(treble)

2

FAD*
(fader)

BAL
(balance)

Adjust the bass. –06 (min.)

to
+06 (max.)

Adjust the treble. –06 (min.)

to
+06 (max.)

Adjust the front
and rear speaker
balance.

R06 (Rear
only)
to
F06 (Front
only)

Adjust the left
and right speaker
balance.

L06 (Left
only)
to
R06 (Right
only)

ENGLISH

Indication pattern changes
as you adjust the level.

LOUD*
(loudness)

1

Boost low and
high frequencies
to produce a well-

LOUD ON

J

LOUD OFF
balanced sound at
low volume level.

VOL*3
(volume)

Adjust the
volume.

00 (min.) to

30 or 50

(max.)*

*1 When you adjust the bass, treble, or

loudness, the adjustment you have made is
stored for the currently selected sound mode
(C-EQ) including “USER.”

2

*

If you are using a two-speaker system, set

the fader level to “00.”

3

*

Normally the +/– buttons work as the volume

control. So you do not have to select “VOL”
to adjust the volume level.

4

*

Depending on the amplifier gain control

setting. (See page 14 for details.)

4

13

General settings — PSM

Basic procedure

You can change PSM (Preferred Setting Mode)
items listed in the table that follows.

ENGLISH

1

Select a PSM item.

2

3 Adjust the PSM item selected.

4 Repeat steps 2 and 3 to adjust the

other PSM items if necessary.

5 Finish the procedure.

Ex.: When you select “AMP GAIN”

Indications Selectable settings, [reference page]

DEMO

Display demonstration

CLOCK H

Hour adjustment

CLOCK M

Minute adjustment

AMP GAIN

Amplifier gain control

DEMO ON: [Initial]; Display demonstration will be activated

automatically if no operation is done for about
20 seconds, [7].

DEMO OFF: Cancels.

1 – 12, [7]

[Initial: 1 (1:00)]

00 – 59, [7]

[Initial: 00 (1:00)]

You can change the maximum volume level of this receiver.
LOW PWR: VOL 00 – VOL 30 (Select this if the maximum power

of the speaker is less than 50 W to prevent them from
damaging the speaker.)

HIGH PWR: [Initial]; VOL 00 – VOL 50

14

Detaching the control panel

When detaching or attaching the control panel,
be careful not to damage the connectors on
the back of the control panel and on the panel
holder.

Detaching the control panel

Before detaching the control panel, be sure to
turn off the power.

Attaching the control panel

ENGLISH

15

Maintenance

How to clean the connectors

Frequent detachment will deteriorate the
connectors.
To minimize this possibility, periodically wipe

ENGLISH

the connectors with a cotton swab or cloth
moistened with alcohol, being careful not to
damage the connectors.

Connector

Moisture condensation

Moisture may condense on the lens inside the
CD player in the following cases:

• After starting the heater in the car.

• If it becomes very humid inside the car.
Should this occur, the CD player may
malfunction. In this case, eject the disc and
leave the receiver turned on for a few hours
until the moisture evaporates.

To keep discs clean

A dirty disc may not play correctly.
If a disc does become dirty, wipe
it with a soft cloth in a straight line
from center to edge.

• Do not use any solvent (for
example, conventional record cleaner, spray,
thinner, benzine, etc.) to clean discs.

To play new discs

New discs may have some rough
spots around the inner and outer
edges. If such a disc is used, this
receiver may reject the disc.
To remove these rough spots, rub the edges
with a pencil or ball-point pen, etc.

How to handle discs

When removing a disc from
its case, press down the center

holder of the case and lift the
disc out, holding it by the
edges.

• Always hold the disc by the edges. Do not
touch its recording surface.

When storing a disc into its case, gently insert
the disc around the center holder (with the
printed surface facing up).

• Make sure to store discs into the cases after
use.

Do not use the following discs:

Warped

disc

Center holder

Sticker

Sticker
residue

Disc

Stick-on
label

16

More about this receiver

Basic operations

Turning off the power

• If you turn off the power while listening to a
disc, disc play will start from where playback
has been stopped previously, next time you
turn on the power.

Tuner operations

Storing stations in memory

• During SSM search...

– All previously stored stations are erased and

stations are stored newly.

– Received stations are preset in No. 1 (lowest

frequency) to No. 6 (highest frequency).

– When SSM is over, the station stored in

No. 1 will be automatically tuned in.

• When storing a station manually, a previously
preset station is erased when a new station is
stored in the same preset number.

Disc operations

General

• Some CD-Rs or CD-RWs may not play
back on this receiver because of their disc
characteristics, and for the following causes:

– Discs are dirty or scratched.
– Moisture condensation occurs on the lens

inside the receiver.
– The pickup lens inside the receiver is dirty.
– CD-R or CD-RW on which the files are

written with “Packet Write” method.
– There are improper recording conditions

(missing data, etc.) or media conditions

(stain, scratch, warp, etc.).

• CD-RWs may require a longer readout time

since the reflectance of CD-RWs is lower
than that of regular CDs.

• Do not use the following CD-Rs or

CD-RWs:

– Discs with stickers, labels, or protective seal

stuck to the surface.
– Discs on which labels can be directly

printed by an ink jet printer.
Using these discs under high temperatures

or high humidity may cause malfunctions or
damage to discs.

ENGLISH

• This receiver has been designed to reproduce
CDs, and CD-Rs (Recordable)/ CD-RWs
(Rewritable) in audio CD (CD-DA) format.

• When a disc has been loaded, selecting “CD”
for the playback source starts disc play.

Inserting a disc

• When a disc is inserted upside down, the disc
automatically ejects.

• Do not insert 8 cm discs (single CD) and
unusual shape discs (heart, flower, etc.) into
the loading slot.

Playing a CD-R or CD-RW

• Use only “finalized” CD-Rs or CD-RWs.

• This receiver can play back multi-session
discs; however, unclosed sessions will be
skipped while playing.

Changing the source

• If you change the source, playback also stops
(without ejecting the disc).

Next time you select “CD” for the playback

source, disc play starts from where it has been
stopped previously.

Ejecting a disc

• If the ejected disc is not removed within
15 seconds, the disc is automatically inserted
again into the loading slot to prevent it from
dust. (Disc will not play this time.)

General settings—PSM

• If you change the “AMP GAIN” setting from
“HIGH PWR” to “LOW PWR” while the
volume level is set higher than “VOL 30,” the
receiver automatically changes the volume
level to “VOL 30.”

17

Troubleshooting

What appears to be trouble is not always serious. Check the following points before calling a service
center.

Symptoms Causes Remedies

ENGLISH

• Sound cannot be heard
from the speakers.

General

• The receiver does not
work at all.

The volume level is set to
the minimum level.

Connections are incorrect. Check the cords and

The built-in microcomputer
may have functioned
incorrectly due to noise, etc.

Adjust it to the optimum
level.

connections.

Reset the receiver (see page

2).

• SSM automatic presetting
does not work.

• Static noise while listening

FM/AM

to the radio.

• Disc automatically ejects. Disc is inserted upside

• CD-R/CD-RW cannot be
played back.

• Tracks on the CD-R/
CD-RW cannot be
skipped.

• Disc can be neither played
back nor ejected.

Disc playback

• Disc sound is sometimes
interrupted.

Signals are too weak. Store stations manually.

The antenna is not connected
firmly.

down.

CD-R/CD-RW is not
finalized.

Disc is locked. Unlock the disc (see page

The CD player may have
functioned incorrectly.

You are driving on rough
roads.

Connect the antenna firmly.

Insert the disc correctly.

• Insert a finalized CD-R/
CD-RW.

• Finalize the CD-R/
CD-RW with the
component which you
used for recording.

11).

Eject the disc forcibly (see
page 2).

Stop playback while driving
on rough roads.

• “NO DISC” appears on the
display.

18

Disc is scratched. Change the disc.

Connections are incorrect. Check the cords and

connections.

No disc is in the loading
slot.

Disc is inserted incorrectly. Insert the disc correctly.

Insert a disc into the loading
slot.

Specifications

AUDIO AMPLIFIER SECTION

Maximum Power Output:
Front: 50 W per channel
Rear: 50 W per channel
Continuous Power Output (RMS):
Front: 19 W per channel into 4 Ω, 40 Hz

to 20 000 Hz at no more than 0.8%
total harmonic distortion.

Rear: 19 W per channel into 4 Ω, 40 Hz

to 20 000 Hz at no more than 0.8%
total harmonic distortion.

Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)
Tone Control Range:

Bass: ±10 dB at 100 Hz
Treble: ±10 dB at 10 kHz
Frequency Response: 40 Hz to 20 000 Hz
Signal-to-Noise Ratio: 70 dB
Line-Out Level/Impedance:

2.0 V/20 kΩ load (full scale)

Output Impedance: 1 kΩ

TUNER SECTION

Frequency Range:
FM: 87.5 MHz to 108.0 MHz
AM: 531 kHz to 1 602 kHz

CD PLAYER SECTION

Type: Compact disc player
Signal Detection System: Non-contact optical

pickup (semiconductor laser)
Number of channels: 2 channels (stereo)
Frequency Response: 5 Hz to 20 000 Hz
Dynamic Range: 96 dB
Signal-to-Noise Ratio: 98 dB
Wow and Flutter: Less than measurable limit

GENERAL

Power Requirement:
Operating Voltage:

DC 14.4 V (11 V to 16 V allowance)
Grounding System: Negative ground
Allowable Operating Temperature:

0°C to +40°C
Dimensions (W × H × D):
Installation Size (approx.):

182 mm × 52 mm × 150 mm
Panel Size (approx.):

188 mm × 58 mm × 11 mm
Mass (approx.):

1.3 kg (excluding accessories)

ENGLISH

[FM Tuner]

Usable Sensitivity: 11.3 dBf (1.0 µV/75 Ω)
50 dB Quieting Sensitivity:

16.3 dBf (1.8 µV/75 Ω)
Alternate Channel Selectivity (400 kHz): 65 dB
Frequency Response: 40 Hz to 15 000 Hz
Stereo Separation: 35 dB
Capture Ratio: 1.5 dB

[AM Tuner]

Sensitivity: 20 µV
Selectivity: 35 dB

Having TROUBLE with operation?

Please reset your unit

Design and specifications are subject to change
without notice.

Refer to page of How to reset your unit

19

EN, IN

© 2004 Victor Company of Japan, Limited

1004DTSMDTJEIN

KD-G116/KD-G115

Installation/Connection Manual
Manual Pemasangan/Penyambungan

GET0252-006A

[UN]

1004DTSMDTJEIN
EN, IN

ENGLISH

This receiver is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your
vehicle does not have this system, a voltage inverter is required, which can be purchased at JVC
car audio dealers.

INDONESIA

Alat penerima ini didisain untuk beroperasi hanya pada 12 V DC, sistem listrik tanah
NEGATIVE. Jika kendaraan anda tidak memiliki sistem ini, sebuah pembalik tegangan

diperlukan, yang mana dapat dibeli di penyalur-penyalur audio mobil JVC.

J

Handles
Pegangan

-pegangan

F

Washer (ø5)
Perapat
sambungan (ø5)

G

Lock nut (M5)
Mur kunci (M5)

H

Mounting bolt (M5 x 20 mm)
Baut bingkai (M5 x 20 mm)

I

Rubber cushion
Bantalan karet

A / B
Hard case/Control panel
Kotak keras/Panel (Papan)
kontrol

D

Trim plate
Plat rapi

E

Power cord
Kabel power

Parts list for installation and connection

The following parts are provided for this receiver.
After checking them, please set them correctly.

Daftar bagian-bagian untuk pemasangan dan penyambungan

Bagian-bagian berikut disediakan untuk alat penerima ini.
Setelah mengecek bagian-bagian tersebut, silahkan atur bagian-bagian itu.

1

INSTALLATION (IN-DASH MOUNTING)

The following illustration shows a typical installation. If you have any questions or require
information regarding installation kits, consult your JVC car audio dealer or a company supplying
kits.

• If you are not sure how to install this receiver correctly, have it installed by a qualifi ed
technician.

PEMASANGAN (BINGKAI-DALAM DASH)

Ilustrasi berikut menunjukkan sebuah tipe pemasangan. Jika anda mempunyai suatu pertanyaan
atau informasi yang diperlukan mengenai alat-alat pemasangan, konsultasikan pada penyalur
audio mobil JVC atau sebuah perusahaan yang mensuplai alat-alat.

• Jika anda tidak yakin bagaimana memasang alat penerima ini dengan benar, biarkan dipasang
dengan teknisi yang berkualitas.

Do the required electrical connections.
Lakukan penyambungan-penyambungan
listrik yang diperlukan.

*

1

When you stand the receiver, be
careful not to damage the fuse on
the rear.

*

1

Ketika anda memberdirikan alat

penerima, hati-hati untuk tidak
merusak sekring di belakang.

Bend the appropriate tabs to hold the
sleeve fi rmly in place.
Bengkokkan pengait-pengait yang
tepat untuk menahan selongsong
secara kuat pada tempatnya.

Removing the receiver

Before removing the receiver, release the rear section.

When installing the receiver without using the sleeve / Ketika memasang alat
penerima tanpa menggunakan selongsong

In a Toyota for example, fi rst remove the car radio and install the receiver in its place.
Dalam sebuah Toyota misalnya, pertama pindahkan radio mobil dan pasang alat penerima tersebut ke dalam
tempatnya.

When using the optional stay /

Ketika menggunakan

penguat tambahan

Note : When installing the receiver on the mounting bracket, make sure to use the 8 mm-long screws. If longer

screws are used, they could damage the receiver.

Catatan: Ketika memasang alat penerima pada breket bingkai, pastikan untuk menggunakan sekrup-skrup

panjang–8 mm. Jika sekrup yang lebih panjang digunakan, maka dapat merusak alat penerima.

Bracket*
Breket*

Bracket*
Breket*

*

Not included for this receiver.

*

Tidak termasuk d

engan alat

penerima ini.

Flat type screws
(M5 x 8 mm)*
Sekrup-sekrup tipe rata
(M5 x 8 mm)*

Pocket
Kantong

Flat type screws
(M5 x 8 mm)

*

Sekrup-sekrup tipe rata
(M5 x 8 mm)*

Screw (option)
Sekrup (tambahan)

Stay (option)
Penguat (tambahan)

Fire wall
Dinding tahan api

Dashboard
Tempat alat pada bagian
depan (dashboard)

Install the receiver at an angle of less than 30˚.
Pasang penerima pada suatu sudut lebih dari 30˚.

TROUBLESHOOTING

• The fuse blows.
* Are the red and black leads connected correctly?

• Power cannot be turned on.
* Is the yellow lead connected?

• No sound from the speake rs.
* Is the speaker output lead short-circuited?

• Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?

• Noise interfere with sounds.
* Is the rear ground terminal connected to the car ’s chassis using shorter and thicker cords?

• Receive r becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?

• This receiver does not work at all.
* Have you reset your receiver?

PEMECAHAN MASALAH

• Sekring meledak.

* Apakah ujung-ujung merah dan hitam tersambung dengan benar?

• Power tidak d apat dihidupkan.

* Apakah ujung kuning sudah tersambung?

• Tidak ada suara dari speker.

* Apakah ujung keluaran speker terhubung pendek?

• Suara terdistorsi.

* Apakah ujung keluaran speker sudah ditanahkan?
* Apakah terminal-terminal “–” dari speker-speker L dan R ditanahkan secara umum?

• Berisik yang mengganggu suara- suara.

* Apakah terminal tanahan belakang tersambung ke casis mobil menggunakan kabel-kabel
terpendek dan tertebal?

• Alat penerima menja di panas.

* Apakah ujung keluaran speker sudah ditanahkan?
* Apakah terminal-terminal “–” dari speker-speker L dan R sudah ditanahkan secara umum?

• Alat penerima ini tidak bekerja sec ara keseluru han.

* Apakah anda sudah reset (memasang kembali) alat penerima anda?

C

Sleeve
Selongsong

Memindahkan alat penerima

Sebelum memindahkan alat penerima, lepaskan seksi belakang.

Insert the two handles, then pull them as illustrated so
that the receiver can be removed.
Sisipkan kedua pemegang dan tarik alat penerima
seperti yang diilustrasikan hingga alat penerima dapat
dipindahkan.

15

ELECTRICAL CONNECTIONS

To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and
make all electrical co fore installing the receiver.

• Be sure to ground this rec eiver to the car’s chassis again after installation.

Notes:

• Replace the fuse with one of the specifi ed rating. If the fuse blows frequently, consult your JVC
car audio dealer.

• It is recommended to connect to the speakers with maximum power of more than 50 W (both
at the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less
than 50 W, change “AMP GAIN” setting to prevent the speakers
from being damaged (see page 14 of the INSTRUCTIONS).

• To prevent short-circuit, cover the terminals of the UNUSED
leads with insulating tape.

• The heat sink becomes very hot after use. Be
careful not to touch it when removing this receiver.

SAMBUNGAN-SAMBUNGAN LISTRIK

Untuk mencegah hubungan pendek, kami menyarankan anda memutuskan sambungan terminal
negatif baterai dan membuat semua sambungan-sambungan listrik sebelum memasang alat
penerima.

• Pastikan untuk mentanahkan alat p enerima ini ke c asis mobil kembali setelah
pemasangan.

Catatan:

• Ganti sekring dengan voltase yang sudah ditetapkan. Jika sekring sering meledak,
konsultasikan pada penyalur audio mobil JVC anda.

• Disarankan untuk menghubungkan speker-speker dengan maksimum power lebih dari

50 W (keduanya di belakang dan di depan, dengan sebuah impedansi 4 Ω sampai 8 Ω).
Jika maksimum power kurang dari 50 W, ganti pengaturan “AMP GAIN” (“PENAMBAH
PENGUAT”) untuk mencegah speker-speker dari kerusakan (lihat halaman 14 dari BUKU
PETUNJUK).

• Untuk mencegah hubungan pendek, tutup ujung-ujung terminal-terminal TIDAK DIGUNAKAN

dengan pita isolasi.

• Pendingin menjadi sangat panas setelah digunakan. Hati-hati untuk tidak menyentuhnya ketika

memindahkan alat penerima ini.

Heat sink
Pendingin

2

ENGLISH INDONESIA

A

Typical connections / Ciri khas sambungan-sambungan

Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause
serious damage to this receiver.
The leads of the power cord and those of the connector from the car body may be different in
color.

1 Connect the colored leads of the power cord in the order specifi ed in the illustration below.
2 Connect the antenna cord.
3 Finally connect the wiring harness to the receiver.

Sebelum p enyambungan: Cek perkabelan dalam mobil dengan hati-hati. Penyambungan
yang tidak benar mungkin menyebabkan kerusakan serius pada alat penerima.
Ujung dari kabel power dan beberapa konektor dari bodi mobil mungkin berbeda dalam warna.

1 Sambungkan ujung berwarna dari kabel power dalam urutan spesifi kasi pada ilustrasi di

bawah.

2 Sambungkan kabel antena.
3 Akhirnya sambungkan dudukan kabel ke alat penerima.

B

Connecting the external amplifi er / Menyambung penguat luar

You can connect an amplifi er to upgrade your car stereo system.

• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so

that it can be controlled through this receiver.

• Disconn ect the spe akers from thi s receiver, conne ct them to the amplifi er. Leave the

speaker le ads of this rec eiver unused.

Anda dapat menyambung sebuah penguat dan peralatan lain untuk meningkatkan sistem
stereo mobil anda.

• Sambungkan ujung jauh (biru dengan strip putih) ke ujung jauh dari peralatan lain sehingga
dapat dikontrol melalui alat penerima ini.

• Putuskan s ambungan se pker- speker dari alat penerima ini, sambungkan ini ke
panguat. Bi arkan ujung speker dari alat penerima ini tidak digunakan.

Signal cord (not supplied for this receiver)
Kabel sinyal (tidak disuplai dengan alat penerima ini)

Front speakers
Speker-speker depan

Rear speakers

Speker-speker belakang

JVC Amplifi er

Penguat JVC

KD- G116
KD- G115

Remote lead
Ujung jauh

Y-connector (not supplied for this receiver)
Konektor Y (tidak disuplai dengan alat penerima ini)

Remote lead (Blue with white stripe)
Ujung jauh (Biru dengan strip putih)

To the remote lead of other equipment or automatic antenna if any
Ke ujung jauh dari peralatan lain atau antena otomatis jika ada

*2 Before checking the operation of this receiver

prior to installation, this lead must be connected,
otherwise power cannot be turned on.

*2

Sebelum pengecekan pengoperasian dari alat
penerima ini sebelum pemasangan, ujung ini
harus sudah

dihubungkan, selain itu power tidak

dapat dihidupkan.

Line out (see diagram )
Keluaran (lihat diagaram

)

Rear ground
terminal
Terminal tanah
belakang

15 A fuse
Sekring 15 A

Antenna terminal
Terminal antena

Black
Hitam

Blue with white stripe
Biru dengan strip putih

Red
Merah

Yellow

*

2

Kuning*

2

*1 Not included for this receiver
*

1

Tidak termasuk untuk alat

penerima

To metallic body or chassis of the car
Ke besi bodi atau casis dari mobil tersebut

To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)
Ke sebuah tempat terminal dalam blok sekring disambungkan ke baterai
mobil (abaikan saklar kontak) (konstant 12 V)

Ignition switch
Saklar kontak

Fuse block
Blok sekring

To an accessory terminal in the fuse block
Ke sebuah terminal aksesoris dalam blok sekring

To the automatic antenna if any (250 mA max.)
Ke antena otomatis jika ada (maksimum 250 mA)

Left speaker (front)
Speker kiri (depan)

Right speaker (front)
Speker kanan (depan)

Left speaker (rear)
Speker kiri (belakang)

Right speaker (rear)
Speker kanan
(belakang)

Purple
Ungu

Purple with black stripe
Ungu dengan strip hitam

Green
Hijau

Green with black stripe
Hijau dengan strip hitam

Gray
Abu-abu

Gray with black stripe
Abu-abu dengan strip
hitam

White
Putih

White with black
stripe
Putih dengan strip
hitam

*3 Firmly attach the ground wire to

the metallic body or to the chassis
of the car—to the place not coated
with paint (if coated with paint,
remove the paint before attaching
the wire). Failure to do so may
cause damage to the receiver.

*

3

Pasangkan dengan kuat kabel

tanah ke bodi besi atau ke casis
dari mobil—pada tempat yang
tidak dilapisi cat (jika dilapisi cat,
hilangkan cat sebelum memasang
kabel). Kegagalan melakukan ini
mungkin menyebabkan kerusakan
pada alat penerima tersebut.

PRECAUTIONS on power supply and speaker
connections:

• DO NOT conne ct the speaker leads of th e power cord to

the car bat tery; otherwise, th e receiver will be serious ly
damaged.

• BEFORE connecting the speaker leads of the power cord to the
speakers, check the speaker wiring in your car.

TINDAKAN-TINDAKAN PENCEGAHAN pada suplai
power dan sambungan-sambungan speker:

• JANGAN sambungkan ujung -u jung speker d ari kabel power

ke baterai mobil; sebaliknya, alat pen erima ters ebut akan
secara serius rusak.

• SEBELUM menyambung ujung-ujung speker dari kabel power ke
speker-speker, cek perkabelan speker dalam mobil anda.

To the remote lead of other equipment (200 mA max.)
Ke ujung jauh dari peralatan lain (maksimum 200 mA)

Blue
Biru

CD RECEIVER KD-G116/KD-G115

KD-G116/KD-G115

ENGLISH

For canceling the display demonstration, see page 7.

For installation and connections, refer to the separate manual.

INSTRUCTIONS

GET0252-007A

[UT]

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and to

obtain the best possible performance from the unit.

ENGLISH

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave

all servicing to qualified service personnel.

3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated.

Avoid direct exposure to beam.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

Warning:

If you need to operate the receiver while
driving, be sure to look ahead carefully or
you may be involved in a traffic accident.

How to forcibly eject a disc

If a disc cannot be recognized by the
receiver or cannot be ejected, ejects the disc
as follows.

How to reset your unit

• This will reset the microcomputer. Your
preset adjustments will also be erased.

• If a disc is loaded, it will eject. Be careful
not to drop the disc.

• If this does not work, try to reset your
receiver.

• Be careful not to drop the disc when it
ejects.

2

Contents

How to reset your unit ........................... 2

How to forcibly eject a disc................... 2

How to read this manual........................ 4

How to use the MODE button ............... 4

Control panel

— KD-G116/KD-G115 ............... 5

Parts identification................................. 5

Getting started....................... 6

Basic operations ........................... 6

Canceling the display demonstrations ... 7

Setting the clock .................................... 7

Radio operations ................... 8

Listening to the radio........................... 8

Storing stations in memory.................... 9

Listening to a preset station ................... 9

Disc operations ...................... 10

Playing a disc ..................................... 10

Selecting the playback modes................ 11

Sound adjustments ................ 12

Selecting preset sound modes

(C-EQ: custom equalizer) .................. 12

Adjusting the sound ............................... 13

ENGLISH

General settings — PSM ......... 14

Basic procedure ..................................... 14

Detaching the control panel.... 15

Maintenance .......................... 16

More about this receiver ........ 17

Troubleshooting ..................... 18

Specifications ......................... 19

*For safety....

• Do not raise the volume level too much, as
this will block outside sounds, making driving
dangerous.

• Stop the car before performing any
complicated operations.

*Temperature inside the car....

If you have parked the car for a long time in
hot or cold weather, wait until the temperature
in the car becomes normal before operating the
unit.

3

How to read this manual

How to use the MODE button

The following methods are used to made the
explanations simple and easy-to-understand:

• Some related tips and notes are explained in

ENGLISH

“More about this receiver” (see page 17).

• Button operations are mainly explained with
the illustrations as follows:

Press briefly.

Press repeatedly.

If you press MODE, the receiver goes into
functions mode, then the number buttons work
as different function buttons.

Ex.: When number button 2 works as

MO (monaural) button.

Press either one.

Press and hold until
your desired response
begins.

Press and hold both
buttons at the same
time.

Time countdown indicator

To use these buttons for original functions
again after pressing MODE, wait for

5 seconds without pressing any of these buttons
until the functions mode is cleared.

• Pressing MODE again also clears the
functions mode.

4

Control panel — KD-G116/KD-G115

Parts identification

Display window

ENGLISH

1 +/– buttons
2 DISP (display) button
3 Loading slot
4 Display window
5 MODE button
6 0 (eject) button
7
8
9 SEL (select) button
p MO (monaural) button
q SSM (Strong-station Sequential Memory)

w CD button
e FM/AM button
r RPT (repeat) button
t RND (random) button
y EQ (equalizer) button
u
i Number buttons

¢/4 buttons

(standby/on/attenuator) button

button

(control panel release) button

Display window

o Tuner reception indicators

MO (monaural), ST (stereo)

; CD indicator
a RND
s RPT (repeat) indicator
d LOUD (loudness) indicator
f EQ (equalizer) indicator
g Sound mode (C-EQ: custom equalizer)

indicators
ROCK, CLASSIC, POPS, HIP HOP, JAZZ,
USER

•
indicator.

h Main display
j Source display

Volume level indicator

(disc random) indicator

also works as the time countdown

5

Getting started

ENGLISH

~

Basic operations

To drop the volume in a moment (ATT)

To restore the sound, press

it again.

Ÿ

You cannot select “CD” as the playback
source if there is no disc in the loading
slot.

!

Volume level appears.

Volume level indicator

To turn off the power

Caution on volume setting:

Discs produce very little noise compared
with other sources. Lower the volume
before playing a disc to avoid damaging
the speakers by the sudden increase of the
output level.

⁄ Adjust the sound as you want.

(See pages 12 and 13.)

6

Canceling the display

Setting the clock

demonstrations

If no operations are done for about 20 seconds,
display demonstration starts.

[Initial: DEMO ON]—see page 14.

1

2

3

1

2

Set the hour and minute.

1 Select “CLOCK H” (hour), then

adjust the hour.

2 Select “CLOCK M” (minute),

then adjust the minute.

3 Finish the procedure.

ENGLISH

Finish the procedure.

4

To activate the display demonstration

In step 3 above...

To check the current clock time when the
receiver is turned off

7

Radio operations

ENGLISH

~

Listening to the radio

2 Select the desired station frequencies.

Lights up when receiving an FM stereo
broadcast with sufficient signal strength.

Selected band appears.

Ÿ Start searching for a station.

When a station is received, searching
stops.
To stop searching, press the same
button again.

To tune in to a station manually

When an FM stereo broadcast is hard to
receive

1

2

Lights up when monaural mode is activated.

In step Ÿ above...
1

8

Reception improves, but stereo effect will
be lost.

To restore the stereo effect, repeat the same
procedure so that the MO indicator goes off.

Storing stations in memory

You can preset six stations for each band.

FM station automatic presetting —

SSM (Strong-station Sequential
Memory)

Select the FM band (FM1 – FM3)

1

you want to store into.

2

3

2

ENGLISH

3

Preset number flashes for a while.

“SSM” flashes, then disappears when
automatic presetting is over.

Local FM stations with the strongest signals are
searched and stored automatically in the FM
band.

Manual presetting

Ex.: Storing FM station of 92.5 MHz into the

preset number 4 of the FM1 band.

1

Listening to a preset station

1

2 Select the preset station (1 – 6) you

want.

To check the current clock time while
listening to an FM or AM station

9

Disc operations

ENGLISH

Playing a disc

All tracks will be played repeatedly until you
stop playback.

Total playing time of
the inserted disc

Elapsed playing
time

Total track number
of the inserted disc

Current track
number

To fast-forward or reverse the track

Fast-forwards.

Reverses.

To go to the next or previous tracks

To the following

tracks.

To the beginning of the current track, then

the previous tracks.

To go to a particular track directly

To select a number from 01 – 06:

To stop play and eject the disc

10

To select a number from 07 – 12:

Prohibiting disc ejection

You can lock a disc in the loading slot.

To cancel the prohibition, repeat the same
procedure.

To check the current clock time while
listening to a disc

Selecting the playback modes

You can use only one of the following playback modes at a time.

1

ENGLISH

2 Select your desired playback mode.

Repeat play

Ex.: When “TRK RPT” is selected

Random play

Ex.: When “DISC RND” is selected

Mode Plays repeatedly

TRK RPT: The current track.

• RPT lights up.

RPT OFF: Cancels repeat play.

Mode Plays at random

DISC RND: All tracks of the current disc.

• RND

RND OFF: Cancels random play.

lights up.

11

Sound adjustments

Selecting preset sound modes (C-EQ: custom equalizer)

ENGLISH

You can select a preset sound mode suitable to
the music genre.

~

Ex.: When “ROCK” is selected

Indication pattern for each sound mode:

Preset values

Indication For:

USER (Flat sound) 00 00 OFF

ROCK Rock or disco

music

CLASSIC Classical

music

POPS Light music +04 +01 OFF

HIP HOP Funk or rap

music

JAZZ Jazz music +02 +03 OFF

1

*

BAS: Bass

2

*

TRE: Treble

3

*

LOUD: Loudness

1

*

BAS

+03 +01 ON

+01 –02 OFF

+02 00 ON

TRE

*

2

LOUD

3

*

12

Adjusting the sound

You can adjust the sound characteristics to your
preference.

1

Ex.: When “TRE” is selected

2

Indication To do: Range

BAS*1
(bass)

1

TRE*
(treble)

2

FAD*
(fader)

BAL
(balance)

Adjust the bass. –06 (min.)

to
+06 (max.)

Adjust the treble. –06 (min.)

to
+06 (max.)

Adjust the front
and rear speaker
balance.

R06 (Rear
only)
to
F06 (Front
only)

Adjust the left
and right speaker
balance.

L06 (Left
only)
to
R06 (Right
only)

ENGLISH

Indication pattern changes
as you adjust the level.

LOUD*
(loudness)

1

Boost low and
high frequencies
to produce a well-

LOUD ON

J

LOUD OFF
balanced sound at
low volume level.

VOL*3
(volume)

Adjust the
volume.

00 (min.) to

30 or 50

(max.)*

*1 When you adjust the bass, treble, or

loudness, the adjustment you have made is
stored for the currently selected sound mode
(C-EQ) including “USER.”

2

*

If you are using a two-speaker system, set

the fader level to “00.”

3

*

Normally the +/– buttons work as the volume

control. So you do not have to select “VOL”
to adjust the volume level.

4

*

Depending on the amplifier gain control

setting. (See page 14 for details.)

4

13

General settings — PSM

Basic procedure

You can change PSM (Preferred Setting Mode)
items listed in the table that follows.

ENGLISH

1

Select a PSM item.

2

3 Adjust the PSM item selected.

4 Repeat steps 2 and 3 to adjust the

other PSM items if necessary.

5 Finish the procedure.

Ex.: When you select “AMP GAIN”

Indications Selectable settings, [reference page]

DEMO

Display demonstration

CLOCK H

Hour adjustment

CLOCK M

Minute adjustment

AMP GAIN

Amplifier gain control

DEMO ON: [Initial]; Display demonstration will be activated

automatically if no operation is done for about
20 seconds, [7].

DEMO OFF: Cancels.

1 – 12, [7]

[Initial: 1 (1:00)]

00 – 59, [7]

[Initial: 00 (1:00)]

You can change the maximum volume level of this receiver.
LOW PWR: VOL 00 – VOL 30 (Select this if the maximum power

of the speaker is less than 50 W to prevent them from
damaging the speaker.)

HIGH PWR: [Initial]; VOL 00 – VOL 50

14

Detaching the control panel

When detaching or attaching the control panel,
be careful not to damage the connectors on
the back of the control panel and on the panel
holder.

Detaching the control panel

Before detaching the control panel, be sure to
turn off the power.

Attaching the control panel

ENGLISH

15

Maintenance

How to clean the connectors

Frequent detachment will deteriorate the
connectors.
To minimize this possibility, periodically wipe

ENGLISH

the connectors with a cotton swab or cloth
moistened with alcohol, being careful not to
damage the connectors.

Connector

Moisture condensation

Moisture may condense on the lens inside the
CD player in the following cases:

• After starting the heater in the car.

• If it becomes very humid inside the car.
Should this occur, the CD player may
malfunction. In this case, eject the disc and
leave the receiver turned on for a few hours
until the moisture evaporates.

To keep discs clean

A dirty disc may not play correctly.
If a disc does become dirty, wipe
it with a soft cloth in a straight line
from center to edge.

• Do not use any solvent (for
example, conventional record cleaner, spray,
thinner, benzine, etc.) to clean discs.

To play new discs

New discs may have some rough
spots around the inner and outer
edges. If such a disc is used, this
receiver may reject the disc.
To remove these rough spots, rub the edges
with a pencil or ball-point pen, etc.

How to handle discs

When removing a disc from
its case, press down the center

holder of the case and lift the
disc out, holding it by the
edges.

• Always hold the disc by the edges. Do not
touch its recording surface.

When storing a disc into its case, gently insert
the disc around the center holder (with the
printed surface facing up).

• Make sure to store discs into the cases after
use.

Do not use the following discs:

Warped

disc

Center holder

Sticker

Sticker
residue

Disc

Stick-on
label

16

More about this receiver

Basic operations

Turning off the power

• If you turn off the power while listening to a
disc, disc play will start from where playback
has been stopped previously, next time you
turn on the power.

Tuner operations

Storing stations in memory

• During SSM search...

– All previously stored stations are erased and

stations are stored newly.

– Received stations are preset in No. 1 (lowest

frequency) to No. 6 (highest frequency).

– When SSM is over, the station stored in

No. 1 will be automatically tuned in.

• When storing a station manually, a previously
preset station is erased when a new station is
stored in the same preset number.

Disc operations

General

• Some CD-Rs or CD-RWs may not play
back on this receiver because of their disc
characteristics, and for the following causes:

– Discs are dirty or scratched.
– Moisture condensation occurs on the lens

inside the receiver.
– The pickup lens inside the receiver is dirty.
– CD-R or CD-RW on which the files are

written with “Packet Write” method.
– There are improper recording conditions

(missing data, etc.) or media conditions

(stain, scratch, warp, etc.).

• CD-RWs may require a longer readout time

since the reflectance of CD-RWs is lower
than that of regular CDs.

• Do not use the following CD-Rs or

CD-RWs:

– Discs with stickers, labels, or protective seal

stuck to the surface.
– Discs on which labels can be directly

printed by an ink jet printer.
Using these discs under high temperatures

or high humidity may cause malfunctions or
damage to discs.

ENGLISH

• This receiver has been designed to reproduce
CDs, and CD-Rs (Recordable)/ CD-RWs
(Rewritable) in audio CD (CD-DA) format.

• When a disc has been loaded, selecting “CD”
for the playback source starts disc play.

Inserting a disc

• When a disc is inserted upside down, the disc
automatically ejects.

• Do not insert 8 cm discs (single CD) and
unusual shape discs (heart, flower, etc.) into
the loading slot.

Playing a CD-R or CD-RW

• Use only “finalized” CD-Rs or CD-RWs.

• This receiver can play back multi-session
discs; however, unclosed sessions will be
skipped while playing.

Changing the source

• If you change the source, playback also stops
(without ejecting the disc).

Next time you select “CD” for the playback

source, disc play starts from where it has been
stopped previously.

Ejecting a disc

• If the ejected disc is not removed within
15 seconds, the disc is automatically inserted
again into the loading slot to prevent it from
dust. (Disc will not play this time.)

General settings—PSM

• If you change the “AMP GAIN” setting from
“HIGH PWR” to “LOW PWR” while the
volume level is set higher than “VOL 30,” the
receiver automatically changes the volume
level to “VOL 30.”

17

Troubleshooting

What appears to be trouble is not always serious. Check the following points before calling a service
center.

Symptoms Causes Remedies

ENGLISH

• Sound cannot be heard
from the speakers.

General

• The receiver does not
work at all.

The volume level is set to
the minimum level.

Connections are incorrect. Check the cords and

The built-in microcomputer
may have functioned
incorrectly due to noise, etc.

Adjust it to the optimum
level.

connections.

Reset the receiver (see page

2).

• SSM automatic presetting
does not work.

• Static noise while listening

FM/AM

to the radio.

• Disc automatically ejects. Disc is inserted upside

• CD-R/CD-RW cannot be
played back.

• Tracks on the CD-R/
CD-RW cannot be
skipped.

• Disc can be neither played
back nor ejected.

Disc playback

• Disc sound is sometimes
interrupted.

Signals are too weak. Store stations manually.

The antenna is not connected
firmly.

down.

CD-R/CD-RW is not
finalized.

Disc is locked. Unlock the disc (see page

The CD player may have
functioned incorrectly.

You are driving on rough
roads.

Connect the antenna firmly.

Insert the disc correctly.

• Insert a finalized CD-R/
CD-RW.

• Finalize the CD-R/
CD-RW with the
component which you
used for recording.

11).

Eject the disc forcibly (see
page 2).

Stop playback while driving
on rough roads.

• “NO DISC” appears on the
display.

18

Disc is scratched. Change the disc.

Connections are incorrect. Check the cords and

connections.

No disc is in the loading
slot.

Disc is inserted incorrectly. Insert the disc correctly.

Insert a disc into the loading
slot.

Specifications

AUDIO AMPLIFIER SECTION

Maximum Power Output:
Front: 50 W per channel
Rear: 50 W per channel
Continuous Power Output (RMS):
Front: 19 W per channel into 4 Ω, 40 Hz

to 20 000 Hz at no more than 0.8%
total harmonic distortion.

Rear: 19 W per channel into 4 Ω, 40 Hz

to 20 000 Hz at no more than 0.8%
total harmonic distortion.

Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)
Tone Control Range:

Bass: ±10 dB at 100 Hz
Treble: ±10 dB at 10 kHz
Frequency Response: 40 Hz to 20 000 Hz
Signal-to-Noise Ratio: 70 dB
Line-Out Level/Impedance:

2.0 V/20 kΩ load (full scale)

Output Impedance: 1 kΩ

TUNER SECTION

Frequency Range:
FM: 87.5 MHz to 108.0 MHz
AM: 531 kHz to 1 602 kHz

CD PLAYER SECTION

Type: Compact disc player
Signal Detection System: Non-contact optical

pickup (semiconductor laser)
Number of channels: 2 channels (stereo)
Frequency Response: 5 Hz to 20 000 Hz
Dynamic Range: 96 dB
Signal-to-Noise Ratio: 98 dB
Wow and Flutter: Less than measurable limit

GENERAL

Power Requirement:
Operating Voltage:

DC 14.4 V (11 V to 16 V allowance)
Grounding System: Negative ground
Allowable Operating Temperature:

0°C to +40°C
Dimensions (W × H × D):
Installation Size (approx.):

182 mm × 52 mm × 150 mm
Panel Size (approx.):

188 mm × 58 mm × 11 mm
Mass (approx.):

1.3 kg (excluding accessories)

ENGLISH

[FM Tuner]

Usable Sensitivity: 11.3 dBf (1.0 µV/75 Ω)
50 dB Quieting Sensitivity:

16.3 dBf (1.8 µV/75 Ω)
Alternate Channel Selectivity (400 kHz): 65 dB
Frequency Response: 40 Hz to 15 000 Hz
Stereo Separation: 35 dB
Capture Ratio: 1.5 dB

[AM Tuner]

Sensitivity: 20 µV
Selectivity: 35 dB

Having TROUBLE with operation?

Please reset your unit

Design and specifications are subject to change
without notice.

Refer to page of How to reset your unit

19

EN, CT

© 2004 Victor Company of Japan, Limited

1004DTSMDTJEIN

KD-G116/KD-G115

Installation/Connection Manual

GET0252-008A

[UT]

1004DTSMDTJEIN
EN, CT

ENGLISH

This receiver is designed to operate on 12 V DC, NEGATIVE ground elect rical systems. If
your vehicle does not have this system, a voltage inverter is required, which can be purchased
at JVC car audio dealers.

J

Handles

F

Washer (ø5)

G

Lock nut (M5)

H

Mounting bolt (M5 x 20 mm)

I

Rubber cushion

A / B
Hard case/Control panel

D

Trim plate

E

Power cord

Parts list for installation and connection

The following parts are provided for this receiver.
After checking them, please set them correctly.

1

INSTALLATION (IN-DASH MOUNTING)

The following illustration shows a typical installation. If you have any questions or require
information regarding installation kits, consult your JVC car audio dealer or a company supplying
kits.

• If you are not sure how to install this receiver correctly, have it installed by a qualified
technician.

Do the required electrical connections.

*

1

When you stand the receiver, be
careful not to damage the fuse on
the rear.

Bend the appropriate tabs to hold the
sleeve firmly in place.

Removing the receiver

Before removing the receiver, release the rear section.

When installing the receiver without using the sleeve /

In a Toyota for example, first remove the car radio and install the receiver in its place.

When using the optional stay /

Note : When installing the receiver on the mounting bracket, make sure to use the 8 mm-long screws. If longer

screws are used, they could damage the receiver.

Bracket*

Bracket*

*

Not included for this receiver.

Flat type screws
(M5 x 8 mm)*

Pocket

Flat type screws
(M5 x 8 mm)

*

Screw (option)

Stay (option)

Fire wall

Dashboard

Install the receiver at an angle of less than 30˚.

TROUBLESHOOTING

• The fuse blows.

* Are the red and black leads connected correctly?

• Power cannot be turned on.

* Is the yellow lead connected?

• No sound from the speakers.

* Is the speaker output lead short-circuited?

• Sound is distor ted.

* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?

• Noise inter fere with sounds.

* Is the rear ground terminal connected to the car ʼs chassis using shorter and thicker cords?

• Receiver b ecomes hot.

* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?

• This receiver does not work at all.

* Have you reset your receiver?

C

Sleeve

Insert the two handles, then pull them as illustrated so
that the receiver can be removed.

15

ELECTRICAL CONNECTIONS

To prevent short circuits, we recommend that you disconnect the batteryʼs negative terminal and
make all electrical connections before installing the receiver.

• Be sure to ground this receiver to the car’s chassis again af ter installat ion.

Notes:

• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC
car audio dealer.

• It is recommended to connect to the speakers with maximum power of more than 50 W (both
at the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less
than 50 W, change “AMP GAIN” setting to prevent the speakers
from being damaged (see page 14 of the INSTRUCTIONS).

• To prevent short-circuit, cover the terminals of the UNUSED
leads with insulating tape.

• The heat sink becomes very hot after use. Be
careful not to touch it when removing this receiver.

Heat sink

2

ENGLISH

A

Typical connections /

Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause
serious damage to this receiver.
The leads of the power cord and those of the connector from the car body may be different in
color.

1 Connect the colored leads of the power cord in the order specified in the illustration below.
2 Connect the antenna cord.
3 Finally connect the wiring harness to the receiver.

B

Connecting the external amplifier /

You can connect an amplifier to upgrade your car stereo system.

• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so
that it can be controlled through this receiver.

• Disconnect the speaker s from this receive r, connect them to the amplifier. Leave the

speaker leads of this receiver unused.

Signal cord (not supplied for this receiver)

Front speakers

Rear speakers

JVC Amplifier

KD-G116
KD-G115

Remote lead

Y-connector (not supplied for this receiver)

Remote lead (Blue with white stripe)

To the remote lead of other equipment or automatic antenna if any

*2 Before checking the operation of this receiver

prior to installation, this lead must be connected,
otherwise power cannot be turned on.

Line out (see diagram )

Rear ground terminal

15 A fuse

Antenna terminal

Black

Blue with white stripe

Red

Yellow*

2

*1 Not included for this receiver

To metallic body or chassis of the car

To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)

Ignition switch

Fuse block

To an accessory terminal in the fuse block

To the automatic antenna if any (250 mA max.)

Left speaker (front)

Right speaker (front) Left speaker (rear)

Right speaker (rear)

PurplePurple with black stripeGreenGreen with black stripeGrayGray with black stripeWhiteWhite with black

stripe

*3 Firmly attach the ground wire to

the metallic body or to the chassis
of the car—to the place not coated
with paint (if coated with paint,
remove the paint before attaching
the wire). Failure to do so may
cause damage to the receiver.

PRECAUTIONS on power supply and speaker
connections:

• DO NOT connect the speaker l eads of the power cord to

the car battery; other wise, the rec eiver will be seriously
damaged.

• BEFORE connecting the speaker leads of the power cord to the
speakers, check the speaker wiring in your car.

To the remote lead of other equipment (200 mA max.)

Blue