Jvc KD-R960BTS, KD-R860BT, KD-AR865BTS User Manual

KD-R960BTS / KD-AR865BTS / KD-R860BT
ENGLISH
FRANÇAIS
ESPAÑOL
CD RECEIVER

INSTRUCTION MANUAL

RÉCEPTEUR CD
RECEPTOR CON CD
MANUAL DE INSTRUCCIONES
Please read all instructions carefully before operation to obtain the best possible performance from the unit.
Veuillez lires les instructions attentivement avant d’utiliser l’appareil afin d’obtenir les meilleures performances possibles de l’appareil.
Por favor lea detenidamente este manual para comprender a fondo todas las instrucciones y obtener un máximo disfrute de esta unidad.
For customer Use:
Enter below the Model No. and Serial No. which are located on the top or bottom of the cabinet. Retain this information for future reference. Model No. Serial No.
B5A-0110-00 [J]
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. In compliance with Federal Regulations, following are reproductions of labels on, or inside the product relating to laser product safety.
JVC KENWOOD Corporation 2967-3, ISHIKAWA-MACHI, HACHIOJI-SHI, TOKYO, JAPAN
THIS PRODUCT COMPLIES WITH DHHS RULES 21CFR SUBCHAPTER J IN EFFECT AT DATE OF MANUFACTURE.
Location : Top Plate
Información acerca de la eliminación de equipos eléctricos y electrónicos al final de la vida útil (aplicable a los países que hayan adoptado sistemas independientes de recogida de residuos)
Los productos con el símbolo de un contenedor con ruedas tachado no podrán ser desechados como residuos domésticos. Los equipos eléctricos y electrónicos al final de la vida útil, deberán ser reciclados en instalaciones que puedan dar el tratamiento adecuado a estos productos y a sus subproductos residuales correspondientes. Póngase en contacto con su administración local para obtener información sobre el punto de recogida más cercano. Un tratamiento correcto del reciclaje y la eliminación de residuos ayuda a conservar los recursos y evita al mismo tiempo efectos perjudiciales en la salud y el medio ambiente.
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
FCC NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Informação sobre a eliminação de pilhas
Este produto não deve ser eliminado como lixo doméstico geral. Devolva a pilha usada ao revendedor ou entidade autorizada para que a mesma seja devolvida ao fabricante ou importador. A reciclagem e a eliminação de lixo de maneira apropriada ajudarão a conservar os recursos naturais ao mesmo tempo que prevenirão os efeitos prejudicais à nossa saúde e ao meio ambiente.
CALIFORNIA, USA ONLY
This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material— special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate
i
Para cumplimiento de la COFETEL:
“La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda
causar su operación no deseada”
IC (Industry Canada) Notice
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device. The term “IC: ” before the certification/ registration number only signifies that the Industry Canada technical specification were met.
Note de IC (Industrie Canada)
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement. L’expression “IC:” avant le numéro d’homologation/ enregistrement signifie seulement que les specifications techniques d’Industrie Canada ont été respectées.
Contains Bluetooth Module FCC ID: ZWYMC55 Contains Bluetooth Module IC: 12033A-MC55
CAUTION
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from person’s body (excluding extremities: hands, wrists, feet and ankles).
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
ATTENTION
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est considérée conforme sans évaluation de l’exposition maximale autorisée. Cependant, cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et le corps (à l’exception des extrémités : mains, poignets, pieds et chevilles).
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.
ii
CONTENTS
BEFORE USE
BEFORE USE 2
BASICS 3
GETTING STARTED 4
CD / USB / iPod / ANDROID 5
RADIO 7
AUX 8
Pandora® 9
iHeartRadio® 10
SiriusXM® Radio
(for
KD-R960BTS / KD-AR865BTS
) 11
BLUETOOTH® 14
AUDIO SETTINGS 20
DISPLAY SETTINGS 22
MORE INFORMATION 24
TROUBLESHOOTING 26
SPECIFICATIONS 28
INSTALLATION / CONNECTION 30
How to read this manual
• Operations are explained mainly
using buttons on the faceplate of
KD-AR865BTS / KD-R860BT
• [
XX
] indicates the selected items.
( XX)
indicates references are
available on the stated page.
.
Warning
Do not operate any function that takes your attention away from safe driving.
Caution
Volume setting:
• Adjust the volume so that you can hear sounds outside the car to prevent accidents.
• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.
General:
• Avoid using the external device if it might hinder safe driving.
• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.
• Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short circuit.
• If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.
Remote control (RM-RK52):
• Do not leave the remote control in hot places such as on the dashboard.
• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.
• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
• Keep the battery out of reach of children and in its original packaging when not in used. Dispose of used batteries promptly. If swallowed, contact a physician immediately.
Maintenance
Cleaning the unit: Wipe off dirt on the faceplate with a dry silicone or soft cloth. Cleaning the connector: Detach the faceplate and clean the connector
gently with a cotton swab, being careful not to damage the connector.
Handling discs:
• Do not touch the recording surface of the disc.
• Do not stick tape etc. on the disc, or use a disc with tape stuck on it.
• Do not use any accessories for the disc.
• Clean from the center of the disc and move outward.
• Clean the disc with a dry silicone or soft cloth. Do not use any solvents.
• When removing discs from this unit, pull them out horizontally.
• Remove burrs from the center hole and disc edge before inserting a disc.
Connector (on the reverse side of the faceplate)
2
BASICS
Faceplate
Volume knob
Detach button
Display window
KD-R960BTS
(turn/press) Loading slot
Attach
Detach
How to reset
Your preset adjustments will also be erased.
Remote control (RM-RK52)
Remote sensor (Do not expose to bright sunlight.)
Pull out the insulation sheet when using for the first time.
How to replace the battery
To On the faceplate On the remote control
Turn on the power
Adjust the volume Turn the volume knob. Press
Select a source
Change the display information
Press
• Press and hold to turn off the power.
Press the volume knob to mute the sound or pause playback.
• Press again to cancel.
• Press
• Press Press
.
repeatedly. , then turn the volume knob within 2 seconds.
repeatedly.
( 25)
or .
Press
• Press again to cancel. Press SOURCE repeatedly.
to mute the sound or pause playback.
ENGLISH
3

GETTING STARTED

1
Cancel the demonstration
Press and hold .
1 2 Turn the volume knob to select [ 3 Turn the volume knob to select [
DEMO
], then press the knob.
DEMOOFF
], then press the knob.
4 Press to exit.
2
Set the clock
Press and hold .
1 2 Turn the volume knob to select [ 3 Turn the volume knob to select [
CLOCK
], then press the knob.
CLOCKSET
], then press the knob.
4 Turn the volume knob to make the settings, then press the knob.
Day
5 Turn the volume knob to select [ 6 Turn the volume knob to select [
knob.
Hour Minute
24H/ 12H 12 HOUR
], then press the knob.
] or [
24 HOUR
], then press the
7 Press to exit.
To return to the previous setting item, press
.
SETTINGS
BEEP
SRC SELECT
AM
*
PANDORA
IHEART
AUX
*
*
ON
:Activates the keypress tone.;
ON
:Enables AM in source selection.;
*
ON
:Enables PANDORA in source selection.;
ON
:Enables IHEARTRADIO in source selection.;
ON
:Enables AUX in source selection.;
OFF
F/W UPDATE
SYSTEM / BLUETOOTH
YES
F/W xxxx
CLOCK
CLOCK SYNC
CLOCK DISP ON
* Not displayed when the corresponding source is selected.
:Starts upgrading the firmware.; NO:Cancels (upgrading is not activated). For details on how to update the firmware, see: <http://www.jvc.net/cs/car/>.
AUTO
:The clock time is automatically set using the Clock Time (CT) data
in FM Radio Broadcast Data System signal.;
:The clock time is shown on the display even when the unit is turned
off.;
OFF
:Cancels.
:Deactivates.
OFF
:Disables.
OFF
OFF
:Disables.
OFF
:Disables.
OFF
:Disables.
:Cancels.
Default:
XX
3
Set the basic settings
Press and hold .
1 2 Turn the volume knob to make a selection (see the following table),
then press the knob.
3 Repeat step 2 until the desired item is selected or activated. 4 Press to exit.
To return to the previous setting item, press
.
4
CD / USB / iPod / ANDROID
Start playback
The source changes automatically and playback starts.
CD
Eject disc Label side
USB input terminal
USB
USB 2.0 cable (commercially available)
*1
iPod/iPhone
(Accessory of the iPod/ iPhone)*
ANDROID
Micro USB 2.0 cable (commercially available)
1
2
*
1
*
To On the faceplate On the remote control
3
Reverse / Fast-forward
Select a track/file Press
4
Select a folder
Repeat play
Random play
*
5
*
5
*
*
Press and hold .
.
Press and hold
Press
Press . Press .
Press repeatedly.
TRACK RPT/ RPT OFF
: Audio CD or JVC Playlist Creator (JPC) /
JVC Music Control (JMC) file
TRACK RPT ONE RPT/ ALL RPT/ RPT OFF
/
FOLDER RPT/ RPT OFF
: iPod or ANDROID
: MP3/WMA/AAC/WAV file
Press repeatedly.
ALL RND/ RND OFF FOLDERRND/ ALL RND/ RND OFF
: Audio CD
: MP3/WMA/AAC/WAV file or JPC / JMC
.
.
( 25)
file
SONG RND/ ALL RND/ RND OFF
1
*
Do not leave the cable inside the car when not using.
2
*
When connecting an Android device, “Press [VIEW] to install JVC MUSIC PLAY APP” is shown. Follow the instructions to install the
: iPod or ANDROID
application. You can also install the latest version of JVC MUSIC PLAY application on your Android device before connecting. (
24
)
3
*
For ANDROID: Applicable only when [
4
*
For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ ANDROID.
5
*
For iPod/ ANDROID: Applicable only when [
AUTO MODE
HEAD MODE
] is selected. ( 6)
]/ [
AUTO MODE
] is selected. ( 6)
ENGLISH
5
CD / USB / iPod / ANDROID
To On the faceplate
Select control mode
Select music drive
While in iPod source, press repeatedly.
HEAD MODE IPHONE MODE
While in ANDROID source, press repeatedly.
AUTO MODE
AUDIO MODE
Press
The stored songs in the following start playback.
• Selected internal or external memory of a smartphone (Mass Storage Class).
• Selected drive of a multiple drives device.
: Control from the unit.
: Control from the iPod/iPhone.
can still play/pause or file skip from the unit.
: Control from the unit (using JVC MUSIC
PLAY application).
: Control other media player applications
from the Android device (without using JVC MUSIC PLAY application). However, you can still play/pause or file skip from the unit.
repeatedly.
However,
Change the playback speed of the Audiobook
While listening to the iPod and [
HEADMODE
] is selected
( Select control mode)
1 Press and hold . 2 Turn the volume knob to select [ 3 Press the volume knob to select [
IPOD
], then press the knob.
AUDIOBOOKS
].
4 Turn the volume knob to make a selection, then press the knob.
0.5×SPEED
Audiobooks sound file in your iPod/iPhone.
(Default: Depends on your iPod/iPhone setting.)
/
1×SPEED
/
2×SPEED
: Select the desired playback speed of the
5 Press to exit.
To return to the previous setting item, press
.
you
....
Select a file from a folder/list
Press .
1 2 Turn the volume knob to select a folder/list, then press the
knob.
3 Turn the volume knob to select a file, then press the knob.
Quick Search
If you have many files, you can search through them quickly.
For MP3/WMA /AAC/WAV or JPC / JMC file:
Turn the volume knob quickly.
For iPod:
You can search for a file according to the first character. Press desired character (A to Z/ 0to9/ OTHERS).
• Select “OTHERS” if the first character is other than Ato Z, 0 to 9.
• To return to the previous setting item, press
• To cancel, press and hold
• For iPod, applicable only when [
control mode
• For ANDROID, applicable only when [ (
Select control mode
or turn the volume knob quickly to select the
.
.
HEADMODE
)
)
] is selected. ( 
AUTO MODE
] is selected.
Select
6
RADIO
Select a stored station
Press one of the number buttons (1to6).
(or) 1 Press 2 Turn the volume knob to select a preset number, then press the
knob to confirm.
“ST” lights up when receiving an FM stereo broadcast with sufficient signal strength.
Search for a station
Press repeatedly to select FM or AM.
1 2 Press (or press on RM-RK52) to search for a station
automatically.
(or) Press and hold (or press and hold on RM-RK52) until
“M” flashes, then press repeatedly to search for a station manually.
Settings in memory
You can store up to 18 stations for FM and 6 stations for AM.
Store a station
While listening to a station....
Press and hold one of the number buttons (1 to 6).
(or) 1 Press and hold the volume knob until “PRESETMODE” flashes. 2 Turn the volume knob to select a preset number, then press the
knob.
The preset number flashes and “MEMORY” appears.
Other settings
Press and hold .
1 2 Turn the volume knob to select [ 3 Turn the volume knob to make a selection
then press the knob.
TUNER
], then press the knob.
(
see the following table),
4 Repeat step 3 until the desired item is selected/activated or follow
the instructions stated on the selected item.
5 Press to exit.
To return to the previous setting item, press
RADIO TIMER
1
*
For
KD-R960BTS
connected. (
2
*
Selectable only when [
Turns on the radio at a specific time regardless of the current source.
1 ONCE/ DAILY/ WEEKLY/ OFF
turned on.
2 FM/ AM/ SIRIUS XM 3 01
to 18 (for FM/ SIRIUS XM)/ 01 to 06 (for AM):Select the preset
station.
4
Set the activation day *2 and time.
M
” lights up when complete.
Radio Timer will not activate for the following cases.
• The unit is turned off.
• [
OFF
] is selected for [AM] in [
selected. (
/
KD-AR865BTS:
11
)
ONCE
] or [
4
WEEKLY
*1:Select the source.
SRCSELECT]
)
Selectable only when SiriusXM Vehicle Tuner is
] is selected in step 1.
:Select how often the timer will be
.
Default:
after Radio Timer for AM is
XX
ENGLISH
7
RADIO
AUX
SSM SSM01–06
to 18 stations for FM. “SSM” stops flashing when the first 6 stations are stored. Select stations.
IF BAND AUTO
MONO
AREA AREAUS
PTY SEARCH
PTY code: NEWS, INFORM
rock),
NOSTALGA SOFTR&B RELTALK
(Spanish talk),
*
ADLTHIT
(adult hits),
(nostalgia),
(soft rhythm and blues),
(religious talk),
MUSCESP
:Increases the tuner selectivity to reduce interference noises from adjacent FM stations. (Stereo effect may be lost.); interference noises from adjacent FM stations, but sound quality will not be degraded and the stereo effect will remain.
Displayed only when the source is FM.
ON
:Improves the FM reception, but the stereo effect will be lost.;
OFF
:Cancels.
10kHz/200kHz.; FM intervals: 10kHz/50kHz.; intervals: 9kHz/50kHz.
Select a PTY code (see below). If there is a station broadcasting a program of the same PTY code as you have selected, that station is tuned in.
(information),
JAZZ, CLASSICL
PERSNLTY
(Spanish music),
/
SSM07–12
SSM07–12
: For North/Central/South America, AM/FM intervals:
AREASA
SOFTRCK
(personality),
/
SSM13–18
/
SSM13–18
:For some South American countries, AM/
AREAEU
SPORTS, TALK, ROCK, CLSROCK
(softrock), (classical),
LANGUAGE, RELMUSC
TOP40, COUNTRY, OLDIES, SOFT
R&B
HIPHOP, WEATHER
:Automatically presets up
to store the following 12
WIDE
:For any other areas, AM/FM
(rhythm and blues),
(religious music),
PUBLIC, COLLEGE, HABLESP
:Subjects to
Default:
(classic
XX
Use a portable audio player
Connect a portable audio player (commercially available).
1
3.5mm (1/8") stereo mini plug with “L” shaped connector (commercially available)
Auxiliary input jack
2 Select [
ON
] for [
AUX
] in [
SRC SELECT
Portable audio player
].
( 4)
3 Press repeatedly to select AUX. 4 Turn on the portable audio player and start playback.
Use a 3-core plug head stereo mini plug for optimum audio output.
,
*
Only for FM source.
8
Pandora®
Preparation:
Install the latest version of the Pandora application on your device (iPhone/ iPod touch), then create an account and log in to Pandora.
• Select [
ON
] for [

PANDORA

] in [
SRC SELECT
].
( 4)
Start listening
Open the Pandora application on your device.
1 2 Connect your device to the USB input terminal.
USB input terminal
1
(Accessory of the iPod/iPhone)
*
The source changes to PANDORA and broadcast starts.
To On the faceplate On the remote control
Playback / pause Press the volume knob.
Skip a track
Thumbs up or thumbs down*
1
*
Do not leave the cable inside the car when not using.
2
*
If thumbs down is selected, the current track is skipped.
Press T. Press I.
Press .
2
Press
Press
.
.
Create and save a new station
Press .
1 2 Turn the volume knob to select [ 3 Turn the volume knob to select [
press the knob.
A new station is created based on the current song or artist.
NEW STATION FROM TRACK
], then press the knob.
] or [
FROM ARTIST
], then
4 Press and hold number button 1, 4, 5 or 6 to store.
To select a stored station, press number button 1, 4, 5 or 6.
Search for a registered station
Press .
1 2 Turn the volume knob to make a selection, then press the knob.
[ [
BYDATE]: A-Z]:
According to the registered date. Alphabetical order.
3 Turn the volume knob to the desired station, then press the knob.
To cancel, press and hold
.
Bookmark a song or artist information
Press and hold the volume knob.
1 2 Turn the volume knob to make a selection, then press the knob.
[
THIS TRACK
[
THIS ARTIST
“BOOKMARKED” appears and the information is stored to your device. The bookmark is available on your Pandora account but not on this
unit.
]: Current song information
]: Current artist information
ENGLISH
9
iHeartRadio®
Preparation:
Install the latest version of iHeart Link for JVC application on your device (iPhone/ iPod touch), then create an account and log in to iHeartRadio.
• Select [
ON
] for [
IHEART
] in [
SRC SELECT
].
( 4)
Start listening
Open the iHeart Link application on your device.
1 2 Connect your device to the USB input terminal.
USB input terminal
1
(Accessory of the iPod/iPhone)
*
3 Press repeatedly to select IHEARTRADIO.
Broadcast starts automatically
To
Playback / pause Press the volume knob.
On the faceplate On the remote control
Press
.
Search for a station
Press .
1 2 Turn the volume knob to select a category, then
press the knob.
3 Turn the volume knob to the desired station, then
press the knob.
When a city list appears, you can skip cities in
alphabetical order.
To cancel, press and hold
.
Skip cities by alphabetical order
While a city list appears during search...
1 Turn the volume knob quickly to enter character
search.
You can search through the list quickly according to
the first character (A to Z).
2 Turn the volume knob or press to select the
character to be search for.
3 Press the volume knob to start searching.
To cancel, press and hold
.
Skip a track for custom station
Thumbs up or thumbs down for custom station*
Create a new/custom station Press and hold the volume
Add to favorite stations for live station
Scan for live station Press 4.—
1
*
Do not leave the cable inside the car when not using.
2
*
If thumbs down is selected, the current track is skipped.
2
Press T. Press I.
Press .
knob. Press 1.—
Press
.
10
SiriusXM® Radio
(for
KD-R960BTS / KD-AR865BTS
)
Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required. For more information, visit www.siriusxm.com.
Preparation:
1 Connect the optional SiriusXM Vehicle Tuner
(commercially available).
Antenna
SiriusXM
Expansion port on the rear panel
Vehicle Tuner
2 Check your Radio ID for activation.
The SiriusXM Radio ID is required for activation and
can be found by tuning to Channel 0 as well as on the label found on the SiriusXM Connect tuner and its’ packaging.
The Radio ID does not include the letters I, O, S or F.
3 Activate the subscription.
For users in U.S.A.:
Online: Go to www.siriusxm.com Phone: Call 1-866-635-2349
For users in Canada:
Online: Go to www.siriusxm.ca/activatexm Phone: Call 1-877-438-9677 4 Press repeatedly to select SIRIUSXM
to start updating.
Start listening
Press repeatedly to select SIRIUSXM.
1 2 Press .
” lights up.
3 Turn the volume knob to select a CATEGORY, then press the knob. 4 Turn the volume knob to select a category from the list, then press the knob.
If “ALL CHANNEL” is selected, all the available channels will be shown.
5 Turn the volume knob to select a channel, then press the knob. (or) Press to search for a channel manually.
• Pressing and holding changes the channel rapidly.
If a locked channel or a mature channel is selected, a pass code input screen appears. Enter the pass code to receive the channel.
( 13)
Store a channel
You can store up to 18 channels.
To Do this
Store a channel Press and hold one of the number buttons (1 to 6).
1 Press and hold the volume knob until “PRESETMODE” flashes. 2 Turn the volume knob to select a preset number, then press
the knob.
The preset number flashes and “MEMORY” appears.
Select a stored channel
Press one of the number buttons (1 to 6).
1 Press . 2 Turn the volume knob to select PRESET, then press the knob. 3 Turn the volume knob to select a preset number, then press
the knob.
Press
on RM-RK52.
ENGLISH
11
SiriusXM® Radio
SiriusXM Replay™
Press the volume knob.
1
” lights up and the unit memorizes this paused position.
2 Press the volume knob to start Replay.
Replay starts from the paused position in step
During Replay...
To On the faceplate On the remote control
Playback / pause Press the volume knob.
Skip the current song backward/forward
Rewind / Fast-forward
Go to Live and exit Reply
Press .
Press and hold
.
Press and hold the volume knob.
1 Press .
1.
Press
Press
Press and hold
.
2 Turn the volume knob to select LIVE, then
press the knob.
SmartFavorites and TuneStart™
When you select a SmartFavorites channel, you can rewind and replay up to 30 minutes of any of the missed news, talk, sports or music content.
• Playback starts from the beginning of the song if [ [
ON
] ( 13) for most music channels stored as a SmartFavorite.
To On the faceplate
Select a stored SmartFavorite channel
Press one of the number buttons (1to6).
1 Press . 2 Turn the volume knob to select PRESET, then
press the knob.
TUNE START
] is set to
3 Turn the volume knob to select a preset number,
then press the knob to confirm.
Cancel
.
SmartFavorites channels
1 Press . 2 Turn the volume knob to select PRESET, then
press the knob.
3 Turn the volume knob to select a preset number,
then press and hold the knob.
” are removed from the last character.
*
Reassign SmartFavorites channels
Repeat steps channels.
” appears at the last character.
*
1 to 3 of cancelling SmartFavorites
User preset channels are initially assigned as the SmartFavorites channels. SmartFavorite channel is available with SXV200 or later SiriusXM tuner models. SiriusXM Vehicle Tuner automatically buffers the broadcast audio content of the SmartFavorites channels in the background.
Using SXV200: This unit can assign a maximum of 6 SmartFavorites channels. If you try to assign the 7th channel, an error beep tone will be heard. Initially, preset channels 1 to 6 are assigned as SmartFavorites.
Using SiriusXM tuner models later than SXV200: This unit can assign
a maximum of 18 SmartFavorites channels. Initially, all preset channels are assigned as SmartFavorites.
• “
” appears at the last character of the channel name for the
*
SmartFavorites channels.
12
TuneScan™
You can get a short preview of the songs that you have missed on each of your SmartFavorite music channels or current tuned music channel.
1 Press . 2 Turn the volume knob to select TUNE SCAN, then press the knob.
Scanning start for the first 6 seconds of the recorded music contents.
• To listen to the current song, press the volume knob to stop scanning. The unit continues playing the current song.
• To select the previous/next song, press
• To cancel scanning, press and hold the volume knob. Playback returns to the channel before you enter TuneScan.
.
SiriusXM® Radio
SiriusXM settings
Press and hold .
1 2 Turn the volume knob to select [
SIRIUSXM
], then press the knob.
3 Turn the volume knob to make a selection (see the following table), then
press the knob.
4 Repeat step 3 until the desired item is selected/activated or follow the
instructions stated on the selected item.
5 Press to exit.
To return to the previous setting item, press
CH LOCK
To unlock settings:
1
Turn the volume knob to select a number.
2
Press to move to the entry position.
3
Repeat steps 1 and 2 to enter the current pass code.
(Initial pass code is 0000.)
4
Press the volume knob to confirm.
.
Default:
XX
2
TUNE START
SIGNAL LVL NO SIGNAL/ WEAK/ GOOD/ STRONG
BUF USAGE 0%
SXM RESET YES
1
*
Displayed only when [
2
*
Available only if the connected SiriusXM Vehical Tuner is SXV200 or later that
supports SmartFavorites.
*
ON
:Selected SmartFavorite channel starts playback from
the beginning of the song.;
of the current received signal.
—
100%(0
buffer.
:Resets stored channel and lock setting to default.;
NO
:Cancels.
USER DEFINED
OFF
:Cancels.
:Shows the strength
):Shows the memory usage for Replay
] is selected.
CODESET
LOCK SET MATURE CH
1
CHEDIT
CHCLEAR
*
1
*
1
Press the volume knob to enter [
2
Turn the volume knob to select a number.
3
Press to move to the entry position.
4
Repeat steps 2 and 3 to enter a new 4-digit pass code.
5
Press the volume knob to confirm.
6
Repeat steps 2 to 5 to reconfirm the pass code.
• Make a note of the new pass code to enter channel lock settings from next time.
user-defined lock setting.;
1
Turn the volume knob to select a category, then press the knob.
2
Turn the volume knob to select a channel you want to lock, then press the knob.
“L” appears in front of the channel number.
3
Press and hold
YES
:Clears all the locked channels.; NO:Cancels.
NEW CODE
:Selects the SiriusXM-defined lock setting.;
OFF
:Cancels.
to exit.
].
USER DEFINED
:Selects the
ENGLISH
13
BLUETOOTH®
BLUETOOTH — Connection
Supported Bluetooth profiles
– Hands-Free Profile (HFP) – Serial Port Profile (SPP) – Phonebook Access Profile (PBAP) – Advanced Audio Distribution Profile (A2DP) – Audio/Video Remote Control Profile (AVRCP)
Supported Bluetooth codecs
– Sub Band Codec (SBC) – Advanced Audio Coding (AAC)
Connect the microphone
Rear panel
Microphone (supplied)
Microphone input jack
Adjust the microphone angle
* For
KD-R960BTS / KD-AR865BTS
microphone input terminal.
*
Secure using cord clamps (not supplied) if necessary.
, connect to the
( 31)
14
Pair a Bluetooth device
When connecting a Bluetooth device to the unit for the first time, perform pairing between the unit and the device.
1 Press to turn on the unit. 2 Search and select “JVC UNIT” on the Bluetooth device.
“BTPAIRING” flashes on the display.
• For some Bluetooth devices, you may need to enter the Personal Identification Number (PIN)
code immediately after searching.
• Refer also to the manual supplied with your Bluetooth device. 3 Perform (A) or (B) depending on what scrolls on the display.
For some Bluetooth devices, pairing sequence may vary from the steps described below.
(A) “[Device Name]” “XXXXXX” “VOL–YES” “BACK–NO” “XXXXXX” is a 6-digit passkey randomly generated during each pairing.
Ensure that the passkey which appears on the unit and Bluetooth device is the same. Press the volume knob to confirm the passkey. Operate the Bluetooth device to confirm the passkey.
(B) “[Device Name]” “VOL–YES” “BACK–NO”
• If only “PAIRING” appears, operate the Bluetooth device to confirm pairing. “PAIRING COMPLETED” appears when pairing is completed and “ connection is established.
• Up to five devices can be registered (paired) in total.
• Only one Bluetooth device can be connected at any time.
• This unit supports Secure Simple Pairing (SSP).
• Some Bluetooth devices may not automatically connect to the unit after pairing. Connect the device to the unit manually. Refer to the instruction manual of the Bluetooth device for more information.
• Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you reset the unit. To delete the paired device,
• When you connect iPhone/ iPod touch/ Android device to the USB input terminal, pairing request (via Bluetooth) is automatically activated. Press the volume knob to pair once you have confirmed the device name.
Automatic pairing request is activated only if: – Bluetooth function of the connected devcie is turned on. – [ – JVC MUSIC PLAY application is installed on the Android device.
Press the volume knob to start pairing.
• If “PAIRING” “PIN 0000” scrolls on the display, enter the PIN code “0000” into the Bluetooth device.
18
)
” will light up when the Bluetooth
AUTO CNNT
You can change to a desired PIN code before pairing. (
18, [
DELETE PAIR
] is set to [ON]. ( 18)
].
BLUETOOTH®
BLUETOOTH — Mobile phone
Receive a call
When there is an incoming call: – For
KD-R960BTS
– For
KD-AR865BTS
– The unit answers the call automatically if [ During a call:
– The buttons and display illuminate according to the settings made for [ – If you turn off the unit or detach the faceplate, the Bluetooth connection is disconnected.
To On the faceplate On the remote control
Answer a call
Reject a call
End a call
: All the buttons and display flash.
/
KD-R860BT
: All the buttons flash.
AUTO ANSWER
Press
Press and hold knob.
Press and hold knob.
or the volume knob.
] is set to a selected time. ( 16)
COLOR
Press
or the volume
or the volume
Press and hold
Press and hold
]. ( 23)
.
Improve the voice quality
While talking on the phone....
1 Press and hold . 2 Turn the volume knob to make a selection
(
see the following table), then press the
knob.
3 Repeat step 2 until the desired item is
selected or activated.
4 Press to exit.
To return to the previous setting item, press
.
MIC LEVEL
NOISE RDCT –5
ECHO CANCEL –5
.
.
–10
—
+10(–4
the microphone increases as the number increased.
—+5(0):Adjust the noise reduction level until the least noise is being heard during a phone conversation.
—+5(0):Adjust the echo cancellation delay time until the least echo is being heard during a phone conversation.
):The sensitivity of
Default:
XX
Adjust the phone volume [
00
] to [50] (Default: [15]*)
Switch between hands­free and private talk modes
* Not applicable for iPhone. During a call, the unit synchronizes the phone volume on the iPhone to the unit.
Turn the volume knob during a call.
• This adjustment will not affect the volume of the other sources.
Press the volume knob during a call.
• Operations may vary according to the connected Bluetooth mobile phone.
ENGLISH
15
BLUETOOTH®
Make the settings for receiving a call
Press to enter Bluetooth mode.
1 2 Turn the volume knob to make a selection
(see the following table), then press the knob.
3 Repeat step 2 until the desired item is
selected or activated.
To return to the previous setting item, press
.
XX
SETTINGS
AUTO ANSWER
Default:
01 SEC —30 SEC
incoming call automatically in the selected time (in seconds).;
OFF
:Cancels.
:The unit answers
Make a call
You can make a call from the call history, phonebook, or dialing the number. Call by voice is also possible if your mobile phone has the feature.
1 Press to enter Bluetooth mode. 2 Turn the volume knob to make a selection (see the following table), then press the knob. 3 Repeat step 2 until the desired item is selected/activated or follow the instructions stated on
the selected item.
To return to the previous setting item, press
1
RECENT CALL
Press the volume knob to select a name or a phone number.
• “>” indicates call received, “<“ indicates call made, “M” indicates call missed.
• “NO HISTORY” appears if there is no recorded call history or call number.
2
Press the volume knob to call.
.
16
PHONEBOOK
1
Press to select the desired letter (A to Z, 0to9, and OTHERS).
• “OTHERS” appears if the first character is other than Ato Z, 0 to 9.
2
Turn the volume knob to select a name, then press the knob.
3
Turn the volume knob to select a phone number, then press the knob to call.
• If the phone supports PBAP, the phonebook of the connected phone is automatically transferred to the unit when pairing.
• This unit can display only non-accent letters. (Accent letters such as “Ú” is showns as “U”.)
BLUETOOTH®
DIAL NUMBER
VOICE
1
Turn the volume knob to select a number (0 to 9) or character ( , #,
+).
2
Press to move the entry position.
Repeat steps
3
Press the volume knob to call.
Speak the name of the contact you want to call or the voice command to control the phone functions.
1
and 2 until you finish entering the phone number.
( 
Make a call using voice recognition
Make a call using voice recognition
Press and hold to activate the connected phone.
1 2 Speak the name of the contact you want to call or the voice
command to control the phone functions.
• Supported Voice Recognition features vary for each phone. Refer to the instruction manual of the connected phone for details.
• This unit also supports the intelligent personal assistant function of iPhone.
Delete a contact
Press to enter Bluetooth mode.
1 2 Turn the volume knob to select [
RECENTCALL
], then press the knob.
3 Turn the volume knob to select a contact. 4 Press and hold to enter delete mode. 5 Turn the volume knob to select [
the knob.
DELETE DELETE ALL
deleted.
: Selected name or phone number in step 3 is deleted.
: All names or phone numbers in [
6 Turn the volume knob to select [
• To return to the previous setting item, press
• Not applicable for mobile phone that supports PBAP.
DELETE
] or [
DELETE ALL
RECENTCALL
YES
], then press the knob.
.
], then press
] in step 2 is
Settings in memory
Store a contact in memory
You can store up to 6 contacts into the number buttons (1 to 6).
1 Press to enter Bluetooth mode. 2 Turn the volume knob to select [
[
)
DIALNUMBER
3 Turn the volume knob to select a contact or enter a phone number.
If a contact is selected, press the volume knob to show the phone
number.
], then press the knob.
RECENTCALL
], [
PHONEBOOK
], or
4 Press and hold one of the number buttons (1 to 6).
“MEMORY P(selected preset number)” appears when the contact is
stored.
To erase a contact from the preset memory, select [ and store a blank number.
DIALNUMBER
Make a call from memory
Press to enter Bluetooth mode.
1 2 Press one of the number buttons (1 to 6). 3 Press the volume knob to call.
“NO PRESET” appears if there is no contacts stored.
Bluetooth mode settings
Press and hold .
1 2 Turn the volume knob to select [ 3 Turn the volume knob to make a selection
knob.
BLUETOOTH
], then press the knob.
( 18)
, then press the
4 Repeat step 3 until the desired item is selected/activated or follow
the instructions stated on the selected item.
5 Press to exit.
To return to the previous setting item, press
.
] in step 2
ENGLISH
17
BLUETOOTH®
Default:
PHONE
AUDIO
APPLICATION
DELETE PAIR
1
*
1
*
*
Selects the phone or audio device to connect or disconnect. “
” appears in front of the device name when connected.
1
Shows the connected phone name using the JVC Smart Music Control app. “
” appears in front of the device name when connected.
1
Turn the volume knob to select a device to delete, then press the
knob.
2
SET PINCODE (0000)
Changes the PIN code (up to 6 digits).
1 2
Repeat steps
3
AUTO CNNCT ON
Bluetooth device is within range.;
AUTO PAIR ON
Turn the volume knob to select [
Turn the volume knob to select a number. Press to move the entry position.
1
and 2 until you finish entering the PIN code.
Press the volume knob to confirm.
:The unit automatically reconnect when the last connected
:The unit automatically pair supported Bluetooth device (iPhone/
YES
] or [NO], then press the knob.
OFF
:Cancels.
iPod touch/ Android device) when it is connected through USB input terminal.Depending on the operating system of the connected device, this function may not work. ;
INITIALIZE YES
:Initializes all the Bluetooth settings (including stored pairing,
phonebook, and etc.).;
INFORMATION
1
*
You can only connect another Bluetooth device by disconnecting the connected Bluetooth
device first. “
2
*
JVC Smart Music Control is designed to view JVC car receiver status and perform simple
MYBTNAME MYADDRESS
: Displays the unit name (JVCUNIT).;
: Shows address of this unit.
” disappears when disconnected.
NO
OFF
:Cancels.
:Cancels.
control operations on Android smart phones. For JVC Smart Music Control operations, visit JVC website: <http://www.jvc.net/cs/car/>.
XX
Bluetooth compatibility check mode
You can check the connectivity of the supported profile between the Bluetooth device and the unit.
• Make sure there is no Bluetooth device paired.
*2
1 Press and hold .
“BLUETOOTH”
PHONE”
“PIN IS 0000” scrolls on the display.
“CHECK MODE” appears. “SEARCH NOW USING
2 Search and select “JVC UNIT” on the Bluetooth device within
3minutes.
3 Perform (A), (B) or (C) depending on what appears on the display.
(A) “PAIRING”
passkey appears on the unit and Bluetooth device, then operate
the Bluetooth device to confirm the passkey. (B) “PAIRING” (C) “PAIRING”: Operate the Bluetooth device to confirm pairing.
After pairing is successful, “PAIRING OK” Bluetooth compatibility check starts. If “CONNECT NOW USING PHONE” appears, operate the Bluetooth device to allow phonebook access to continue.
“XXXXXX” (6-digit passkey): Ensure that the same
“PIN IS 0000”: Enter “0000” on the Bluetooth device.
“[Device Name]” appears and
The connectivity result flashes on the display.
“PAIRING OK” and/or “H.FREE OK”*1 and/or “A.STREAM OK”*2 and/or “PBAP OK”*
1
*
Compatible with Hands-Free Profile (HFP)
2
*
Compatible with Advanced Audio Distribution Profile (A2DP)
3
*
Compatible with Phonebook Access profile (PBAP)
After 30 seconds, “PAIRING DELETED” appears to indicate that pairing has been deleted, and the unit exits check mode.
• To cancel, press and hold
on the power again.
3
: Compatible
to turn off the power, then turn
18
BLUETOOTH®
BLUETOOTH — Audio
Audio player via Bluetooth
Press repeatedly to select BTAUDIO (or press SOURCE on RM-RK52).
1 2 Operate the Bluetooth audio player to start playback.
To On the faceplate On the remote control
Playback / pause
Select group or folder Press
Reverse / Forward skip
Reverse / Fast-forward Press and hold
Repeat play Press
Random play
Operations and display indications may differ according to their availability on the connected device.
Press
Press
TRACKRPT, ALLRPT, RPTOFF
Press
GROUPRND, ALLRND, RNDOFF
.
. Press .
.
repeatedly.
repeatedly.
Press
Press
.
Press and hold
.
.
Internet radio via Bluetooth
Listen to Pandora
Preparation:
Select [ You can listen to Pandora on your smart phone
(Android OS) through Bluetooth on this unit.
ON
] for [
PANDORA
] in [
SRC SELECT
].
( 4)
1 Open the Pandora application on your device. 2 Connect your Bluetooth audio player via
Bluetooth connection. (
14)
3 Press repeatedly to select PANDORA.
The source switches and broadcast starts
automatically.
You can operate Pandora in the same way as Pandora for iPod/iPhone. (
9)
Listen to iHeartRadio
Preparation:
Select [
.
You can listen to iHeartRadio on your smart phone (Android OS) through Bluetooth on this unit.
ON
] for [
IHEART
] in [
SRC SELECT
].
( 4)
1 Open the iHeart Link application on your smart
phone.
2 Connect your smart phone via Bluetooth
connection. (
14)
3 Press repeatedly to select
IHEARTRADIO.
The source switches and broadcast starts
automatically.
You can operate iHeartRadio in the same way as iHeartRadio for iPod/iPhone. (
10)
ENGLISH
19
AUDIO SETTINGS
To
Select a preset equalizer
On the faceplate
Press
Press
repeatedly.
, then turn the volume knob within
2seconds.
Preset equalizer: FLAT TALK, USER1, USER2, VOCAL BOOST, BASS BOOST, CLASSICAL
(default),
HARD ROCK, JAZZ, POP, R&B
,
,
DANCE
Store your own sound settings
1 Press and hold . 2 Turn the volume knob to select [
EASY EQ
], then
press the knob.
3 Turn the volume knob to select [
USER1
] or [
USER2
],
then press the knob.
4 Turn the volume knob to make a selection, then
press the knob.
For settings, refer to step
• To return to the previous setting item, press
• To exit, press
2 of [
.
EASYEQ
]
.
Other settings
Press and hold .
1 2 Turn the volume knob to make a selection (see the following table),
then press the knob.
3 Repeat step 2 until the desired item is selected/activated or follow the
instructions stated on the selected item.
4 Press to exit.
To return to the previous setting item, press
EQSETTING
EQPRESET
FLAT/
HARD ROCK/
VOCALBOOST/
JAZZ/
POP/
BASSBOOST/
R&B/
CLASSICAL/
.
TALK/
DANCE
Default:
USER1/
USER2/
:Selects a preset equalizer.
XX
EASYEQ
1 USER1/ USER2 2
Adjust your own sound settings.
SUB.W SP SUB.W
SUB.W SP SUB.W
PRO EQ
(For
1 USER1/ USER2 2 BASS 3
Adjust the sound elements of the selected sound tone.
Level: Q:
Level: Q:
Level: Q:
1
*
Displayed only when [
2
*
Displayed only when [
3
*
Displayed only when [
(
22)
4
*
Displayed only when [
(
22)
(For
KD-R960BTS
2
*1*
3
*1*
:
BASSLVL MIDLVL: TRELVL
(For
BASSLVL MIDLVL: TRELVL
KD-R960BTS
BASS
MIDDLE
TREBLE
:
:
KD-AR865BTS
2
*1*
4
*1*
:
:
:
/
/
MIDDLE
Frequency: 60/ 80/
Frequency:
Frequency:
SUB.W
] is set to [ON]. ( 21)
SPK/PREOUT SPK/PREOUT
SPK/PREOUT
:Select a preset name.
/
KD-R860BT
:
00
)
to
–08 –06 –06 –06
)
:
00
to
–08 –10 –10 –10
KD-R860BT
)
:Select a preset name.
/
TREBLE
:Select a sound tone.
100/ 200HZ
–06
to
+06
Q1.0/ Q1.25/ Q1.5/ Q2.0
0.5/ 1.0/ 1.5/ 2.5KHZ
to
+06
–06 Q0.75/ Q1.0/ Q1.25
10.0/ 12.5/ 15.0/ 17.5KHZ
to
+06
SUB.W/SUB.W REAR/SUB.W
REAR/REAR
–06 QFIX
] is set to [ ] is set to [
] is set to [
+06
(Default:
to
+08
to
+06
to
+06
to
+06
00)
+06
(Default:
to
+08
to
+10
to
+10
to
+10
00)
(
Default:
80HZ 00
(Default:
(Default:
Q1.0
)
1.0KHZ 00 Q1.25
10.0KHZ 00 QFIX
)
]. ( 22)
] or [
SUB.W/SUB.W
] or [
SUB.W/SUB.W
].
].
03 00 00 00
03 00 00 00
)
20
AUDIO SETTINGS
PRO EQ
(For
KD-AR865BTS
1 USER1/ USER2 2 BASS 3
/
MID BASS / MID / MID HIGH
Adjust the sound elements of the selected sound tone.
BASS
Frequency: 63/ 80/ Level: Q:
MID BASS
Level: Q:
MID
Frequency: Level: Q:
MID HIGH
Level: Q:
HIGH
Frequency: Level: Q:
AUDIO
BASS BOOST
+01
/
+02
)
:Select a preset name.
/
HIGH
:Select a sound tone.
(
–10
100/ 125HZ
to
+10
Q1.0/ Q1.25/ Q1.5/ Q2.0
Frequency:
200/ 250/ 315/ 400HZ
to
+10
–10 Q1.0/ Q1.25/ Q1.5/ Q2.0 630/ 800HZ/ 1.0/ 1.25KHZ
to
+10
–10 Q0.75/ Q1.0/ Q1.25/ Q2.0
Frequency:
2.0/ 2.5/ 3.15/ 4.0KHZ
to
+10
–10 Q0.75/ Q1.0/ Q1.25/ Q2.0
6.3/ 8.0/ 10.0/ 12.5KHZ
to
+10
–10 Q0.75/ Q1.0/ Q1.25/ Q2.0
: Selects your preferred bass boost level.;
Default:
80HZ 00
(Default:
(Default:
Q1.25 250HZ 00 Q1.25 800HZ 00 Q1.0
(Default:
2.5KHZ 00 Q1.0
(Default:
8.0KHZ 00 Q1.0)
OFF
:Cancels.
5
SUB.WPHASE
*
REVERSE
(180°)/
NORMAL
(0°):Selects the phase of the subwoofer output to be in line with the speaker output for optimum performance. (Selectable only if a setting other than [ [
SUB.WLPF
HPF
)
(For
KD-AR865BTS
OFF
:All signals are sent to the front/rear speakers.;
MID120HZ
].)
)
/
HIGH150HZ
:Audio signals with frequencies lower than
THROUGH
] is selected for
LOW100HZ
/
100Hz/ 120Hz/ 150Hz are cut off from the front/rear speakers.
FADER R06
)
8
BALANCE
)
VOL ADJUST –05
*
L06
—
—
—
F06(00
R06(00
+05(00
):Adjusts the front and rear speaker output balance.
):Adjusts the left and right speaker output balance.
):Presets the volume adjustment level of each source (compared to the FM volume level). Before adjustment, select the source you want to adjust. (“VOLADJFIX” appears if FM is selected.)
)
AMP GAIN LOWPOWER
:Limits the maximum volume level to 30. (Select if the
maximum power of each speaker is less than 50W to prevent damaging
D.T.EXP
(Digital Track Expander)
the speakers.);
ON
:Creates realistic sound by compensating the high-frequency components and restoring the rise-time of the waveform that are lost in audio data compression.;
HIGHPOWER
OFF
:The maximum volume level is 50.
:Cancels.
LOUD 01
low volume.;
SUB.W LEVEL
5
*
SPK-OUT
PRE-OUT
7
*
SUB.W
SUB.WLPF
5
*
ON
THROUGH HIGH120HZ
120Hz are sent to the subwoofer.
/02:Boosts low or high frequencies to produce a well-balanced sound at
OFF
:Cancels.
6
*
00
to
+06(+03
connected via speaker lead. (
7
*
–08
to
+08(00
):Adjusts the output level of the subwoofer
31, 32
)
):Adjusts the output level of the subwoofer connected to the lineout terminals (SW or REAR/SW) through an external amplifier. (
/
OFF
: Turns on or off the subwoofer output.
:All signals are sent to the subwoofer. ;
31, 32
)
LOW55HZ
/
MID85HZ
:Audio signals with frequencies lower than 55Hz/ 85Hz/
/
SPK/PREOUT
5
*
Displayed only when [
6
*
Displayed only when [
7
*
For unit with 3-pair lineout terminals: Displayed only when [
[
REAR/REAR
Selects the appropriate setting to get the desired output. (
SUB.W
] is set to [ON].
] or [
SUB.W/SUB.W
SPK/PREOUT
] is set to [
]. (22
SUB.W/SUB.W
) For unit with 2-pair lineout terminals: Displayed only when [ [
REAR/SUB.W
8
*
This adjustment will not affect the subwoofer output.
] or [
SUB.W/SUB.W
]. (22
)
]. (22
)
SPK/PREOUT
SPK/PREOUT
ENGLISH
22).
] is set to
] is set to
21
AUDIO SETTINGS

DISPLAY SETTINGS

SPK/PRE OUT
Connection via lineout terminals (
(For
KD-R960BTS
Setting
REAR/REAR
REAR/SUB.W
SUB.W/SUB.W
(For
KD-AR865BTS
Setting
REAR/REAR
REAR/SUB.W
SUB.W/SUB.W
/
KD-R860BT
Front speakers output Rear speakers output
Front speakers output Subwoofer output
Front speakers output Subwoofer output
)
Front speakers output Rear speakers output Subwoofer output
Front speakers output L (left): Subwoofer output
)
FRONT REAR/SW
FRONT REAR SW
———
R (right): (Mute)
Connection via speaker leads ( 
Setting
REAR/REAR
REAR/SUB.W
SUB.W/SUB.W
If [
SUB.W/SUB.W
– [
HIGH120HZ
– [
R01
] is selected in [
Rear speakers output Rear speakers output
Rear speakers output Rear speakers output
Subwoofer output (Mute)
] is selected:
] is selected in [
FADER
L (left) R (right)
SUB.WLPF
] and selectable range is [
31, 32
Lineout terminal
Lineout terminal
31, 32
)
Rear speaker lead
] and [
THROUGH
)
Subwoofer output
] is not available.
R06
]to [00]
KD-AR865BTS / KD-R860BTKD-R960BTS
1 Press and hold . 2 Turn the volume knob to make a selection (see the following table),
then press the knob.
3 Repeat step 2 until the desired item is selected/activated or follow
the instructions stated on the selected item.
4 Press to exit.
To return to the previous setting item, press
DISPLAY
DIMMER
1
*
The illumination control wire connection is required.
Selects the display and button illumination adjusted in the [ setting.
OFF
:Selects the day adjustments.; ON:Selects the night adjustments.;
DIMMER TIME
Turn the volume knob to adjust the [ Turn the volume knob to adjust the [ (Default: [ [
AUTO
:Changes between the day and night adjustments when you turn off or
on the car headlights. * For
KD-R960BTS
settings made on [
:Adjusts the dimmer on and off time.
ON OFF
ON
]: 18:00 or 6:00 PM
OFF
]: 6:00 or 6:00 AM)
1
, the display and button colors change according to the
COLOR
].
] time, then press the knob.
( 31, 32)
.
Default:
BRIGHTNESS
] time, then press the knob.
XX
]
22
DISPLAY SETTINGS
BRIGHTNESS
SCROLL
COLOR
PRESET
2
*
3
*
2
*
(for
Some characters or symbols will not be shown correctly (or will be blanked). If one of these color pattern is selected, the [
color will change to the default color.
Sets the button, display and USB input terminal brightness for day and night separately.
1 DAY / NIGHT 2
Select a zone for setting.
3
Set the brightness level (00 to 31). (Default:
ONCE
:Scrolls the display information once.;
5-second intervals.;
KD-R960BTS
)
You can select a color for [ separately. For [ Default color:
ALLZONE DISPZONE
1
Select a zone for setting.
2
Select a color for the selected zone.
COLOR01
USER
[
NIGHTCOLOR
COLORFLOW01
speeds.
GROOVE/ TECHNO/ EMOTION/ RELAX/ SPECTRUM/ SWEEP POP
[
ALLZONE
:Select day or night.
( 22)
DAY:31
AUTO
OFF
:Cancels.
ALLZONE
ALL ZONE
: [
COLOR06
: [
COLOR01
to
: The color you have created for [
: The selected color pattern is shown.*3 (Selectable only when
] is selected in step
], you can also select a color pattern.
],
ZONE 1
],
ZONE 2
COLOR29
] is shown.
to
COLORFLOW03
ZONE1
: [
( 22)
], [
ZONE1
COLOR06
: [
COLOR27
1.)
], [
DISPZONE
], [
],
]
DAYCOLOR
: Color changes at different
;
NIGHT:15
:Repeats scrolling at
DISPZONE
], [
ZONE2
], or [
] or
] illumination
)
ZONE2
/
]
DAYCOLOR
NIGHTCOLOR
COLOR GUIDE
[
NIGHTCOLOR
headlight.
Store your own day and night colors for different zone.
1
Select a zone for setting.
2 RED 3 00
Repeat steps
• Your setting is stored to [
• If [
ON
jack illumination when settings are performed on menu and list search. Display zone will automatically change depending on volume level.;
OFF
] or [
/
GREEN
/
BLUE
to 31:Select the level.
2
and 3 for all the primary colors.
00
] is selected for all primary colors for [
appears on the display.
:Changes the button, display, USB input terminal and auxiliary input
:Cancels.
DAYCOLOR
] is changed by turning on or off your car’s
( 22)
:Select a primary color.
USER
] in [
PRESET
].
DISPZONE
], nothing
ENGLISH
23
MORE INFORMATION
About discs and audio files
• This unit can only play the following CDs:
• This unit can play back multi-session discs; however, unclosed sessions will be skipped during playback.
Unplayable discs:
- Discs that are not round.
- Discs with coloring on the recording surface or discs that are dirty.
- Recordable/ReWritable discs that have not been finalized.
- 8 cm CD. Attempting to insert using an adapter may cause malfunction.
DualDisc playback:
Disc Digital Audio” standard. Therefore, the use of Non-DVD side of a DualDisc on this product cannot be recommended.
Playable files:
- File extensions: MP3(.mp3), WMA(.wma), AAC (.m4a)
- Bit rate: MP3: 8kbps — 320kbps
WMA: 32kbps — 192kbps AAC: 8kbps — 320kbps
- Sampling frequency:
MP3: 48kHz, 44.1kHz, 32kHz, 24kHz, 22.05kHz, 16kHz, 12kHz, 11.025kHz, 8kHz WMA: 8kHz — 48kHz AAC: 8kHz — 48kHz
- Variable bit rate (VBR) files.
Maximum number of characters for file/folder name:
It depends on the disc format used (includes 4 extension characters—<.mp3>, <.wma> or
<.m4a>).
- ISO 9660 Level 1 and 2: 32 characters
- Romeo: 32 characters
- Joliet: 32 characters
- Windows long file name: 32 characters
The Non-DVD side of a “DualDisc” does not comply with the “Compact
About USB devices
• This unit can play MP3/WMA/AAC/WAV files stored on a USB mass storage class device.
• You cannot connect a USB device via a USB hub.
• Connecting a cable whose total length is longer than 5m may result in abnormal playback.
• The maximum number of characters for:
- Folder names: 64 characters
- File names: 64 characters
- MP3 Tag: 64 characters
- WMA Tag: 64 characters
- AAC Tag: 64 characters
- WAV Tag: 64 characters
• This unit can recognize a total of 20 480 files, 999 folders (999 files per folder including folder without unsupported files), and of 8 hierarchies.
• This unit cannot recognize a USB device whose rating is other than 5V and exceeds 1A.
About iPod/iPhone
Made for
- iPod touch (2nd, 3rd, 4th, and 5th generation)
- iPod classic
- iPod nano (3rd, 4th, 5th, 6th, and 7th generation)
- iPhone 3G, 3GS, 4, 4S, 5, 5S, 5C
• It is not possible to browse video files on the “Videos” menu in
• The song order displayed on the selection menu of this unit may differ from that of the iPod/ iPhone.
• If some operations are not performed correctly or as intended, visit: <http://www.jvc.net/cs/car/>.
About Android device
• This unit supports Android OS 4.1 and above.
• Some Android devices (with OS4.1 and above) may not fully support Android Open Accessory (AOA)2.0.
• If the Android device supports both mass storage class device and AOA2.0, this unit always playback via AOA2.0 as priority.
• For more information and the latest compatible list, see: <http://www.jvc.net/cs/car/>.
[HEAD MODE]
.
24
MORE INFORMATION
About Pandora
• Pandora is available only in the U.S., Australia and New Zealand.
• Because Pandora is a third-party service, the specifications are subject to change without prior notice. Accordingly, compatibility may be impaired, or some or all of the services may become unavailable.
• Some functions of Pandora cannot be operated from this unit.
• For issues using the application, please contact Pandora at pandora-support@pandora.com.
About iHeartRadio
• iHeartRadio® is available only in the U.S., Australia and New Zealand.
• iHeartRadio® is a third-party service, therefore the specifications are subject to change without prior notice. Accordingly, compatibility may be impaired or some or all of the services may become unavailable.
• Some functions of iHeartRadio® cannot be operated from this unit.

About JVC Playlist Creator and JVC Music Control

• This unit supports the PC application JVC Playlist Creator and AndroidTM application JVC Music Control.
• When you play audio file with song data added using the JVC Playlist Creator or JVC Music Control, you can search for audio file by Genres, Artists, Albums, Playlists, and Songs.
• JVC Playlist Creator and JVC Music Control are available from the following web site: <http://www.jvc.net/cs/car/>.
About Bluetooth
• Depending on the Bluetooth version of the device, some Bluetooth devices may not be able to connect to this unit.
• This unit may not work with some Bluetooth devices.
• Signal conditions vary, depending on the surroundings.
• For more information about Bluetooth, visit the following JVC website: <http://www.jvc.net/cs/car/>.
Change the display information
Press repeatedly.
FM
or
AM
Station name (PS)*1 Frequency Program type (PTY)*1*2 Title*1*2
Day/Clock (back to the beginning)
1
*
For FM Radio Broadcast Data System stations only.
2
*
If unavailable, “NO PTY” / “NO TEXT” appears.
CD
or
USB
USB-IPOD USB-ANDROID
PANDORA
IHEART
Playing time Day/Clock Disc name*3 Album title/Artist*4 Track
5
title*
* * * *
Folder/file name*6 (back to the beginning)
3
Only for CD-DA: If not recorded, “NO NAME” appears.
4
Only for MP3/WMA/AAC/WAV files: If not recorded, “NO NAME” appears.
5
If not recorded, “NO NAME” appears.
6
Only for MP3/WMA/AAC/WAV files.
Playing time Day/Clock Album title/Artist*7 Track title*7 (back to the beginning)
7
*
If not recorded, “NO NAME” appears.
Station name Album title/Artist Track title Playing time Day/ Clock
(back to the beginning)
Station name Track title*8 Track Artist*8 Day/Clock (back to the beginning)
8
*
If unavailable, station name appears.
SiriusXM
AUX
BT AUDIO
Channel no./Channel name B Artist B Song title B Content information
B
Category name B Day/Clock B (back to the beginning)
AUX Day/Clock
Playing time Day/Clock Album title/Artist*9 Track title*9 (back to the beginning)
9
*
If not recorded, “UNKNOWN” appears.
ENGLISH
25

TROUBLESHOOTING

Symptom Remedy
Sound cannot be heard. • Adjust the volume to the optimum level.
• Check the cords and connections.
“MISWIRING CHECK WIRING THEN PWR ON” appears.
General
“PROTECTING SEND SERVICE” appears.
Source cannot be selected. Check the [
• Radio reception is poor.
• Static noise while
Radio
listening to the radio.
Disc cannot be ejected.
“IN DISC” appears. Make sure nothing is blocking the loading slot when you
“PLEASE” and “EJECT” appear alternately.
Playback order is not as intended.
Elapsed playing time is not correct.
CD / USB / iPod
“NOT SUPPORT” appears and track skips.
“READING” keeps flashing. • Do not use too many hierarchical levels and folders.
“CANNOT PLAY” flashes and/or connected device cannot be detected.
Turn the power off, then check to be sure the terminals of
the speaker wires are insulated properly. Turn the power on again.
Send the unit to the nearest service center.
SRCSELECT
• Connect the antenna firmly.
• Pull the antenna out all the way.
Press and hold
to drop the disc when it is ejected.
eject the disc.
Press
The playback order is determined by the file name (USB)
or the order in which files were recorded (disc).
This depends on the recording process earlier.
Check whether the track is a playable format.
• Reload the disc or reattach the USB device.
• Check whether the connected device is compatible with this unit and ensure the files are in supported formats. (
• Reattach the device.
, then insert the disc correctly.
] setting.
to forcibly eject the disc. Be careful not
( 4)
( 24)
24)
Symptom
The iPod/iPhone does not turn on or does not work.
Correct characters are not displayed.
CD / USB / iPod
• Sound cannot be heard during playback.
• Sound output only from the Android device.
Cannot playback at [
].
MODE
ANDROID
“NO DEVICE” or “READING” keeps flashing.
Playback is intermittent or sound skips.
“CANNOT PLAY” • Make sure Android device contains playable audio files.
“ADDERROR” “SEARCHERR”
“CHKDEVICE” Check the Pandora application on your device.
Pandora
“NOSKIPS” The skip limit has been reached.
AUTO
Remedy
• Check the connection between this unit and iPod/iPhone.
• Detach and reset the iPod/iPhone using hard reset.
This unit can only display uppercase letters, numbers,
and a limited number of symbols.
• Reconnect the Android device.
AUDIO MODE
• If in [ on the Android device and start playback.
AUDIO MODE
• If in [ application or use another media player application.
• Restart the Android device.
• If this does not solve the problem, the connected Android device is unable to route the audio signal to unit. (
• Make sure JVC MUSIC PLAY APP is installed on the Android device. (5)
• Reconnect the Android device and select the appropriate control mode. (
• If this does not solve the problem, the connected Android device does not support [
• Switch off the developer options on the Android device.
• Reconnect the Android device.
• If this does not solve the problem, the connected Android device does not support [
Turn off the power saving mode on the Android device.
• Reconnect the Android device.
• Restart the Android device.
New station creation is unsuccessful.
], launch any media player application
], relaunch the current media player
6
)
AUTO MODE
AUTO MODE
]. (
]. (
24
24
24
)
)
)
26
TROUBLESHOOTING
Symptom Remedy
“NOSTATIONS” No stations are found. “STATIONLIM” The number of registered stations has reached its limit.
Retry after deleting unnecessary stations from your device.
“UPGRADEAPP” Make sure you have installed the latest version of the
Pandora application on your device.
Pandora
“CONNECT ERR” Communication is unstable. “RATING ERR” Registration of thumbs up/thumbs down has failed. “LICENSE ERR” You try to access from a country which Pandora is not
deliverable.
Station cannot be selected. If “Explicit Content” in [Account Settings] is checked in
the web version of iHeartRADIO, custom stations become
unavailable. “CREATE ERR” Custom station name creation is unsuccessful. “SAVE ERROR” Addition to the favorite category failed. “DISCONNCTED” Check the connection to the device. “NOSKIPS” The skip limit has been reached. Retry later. “NOSTATIONS” No stations are found. “NOT CONNCTD” Link to the application is impossible. “UPDATE APP” Make sure you have installed the latest version of the
iHeartRadio
iHeart Link for JVC application on your device. “PLS LOGIN” You haven’t log in. Log in again. “STATION NOT AVAILABLE” Broadcast from the station is over. “STATION NOT SELECTED” No station is selected. “STREAM ERR” Broadcast data is interrupted. “THUMBS ERR” Registration of Thumbs Up/Down has failed. “TIMED OUT” The request has resulted in time-out.
Symptom Remedy
“CHLOCKED LOCK CODE?”
“CHANUNSUB” The selected channel is unsubscribed.
“CHUNAVAIL” The selected channel is unavailable. Visit
“CHKANTENNA” Check the antenna and its connection are in good condition. “CHECKTUNER” Make sure the SiriusXM Vehicle Tuner is connected to the
SiriusXM® Radio
“NOSIGNAL” Make sure the antenna is mounted outside the vehicle. “SUBSCRIPTION
UPDATED – PRESS ENTER TO CONTINUE.”
“CODE ERROR” Make sure you have entered the correct pass code. “NO CONTENT” There is insufficient content to start TuneScan. “SCAN CANCEL” TuneScan has been aborted. No Bluetooth device is
detected. Pairing cannot be
made.
Echo or noise occurs. • Adjust the microphone unit’s position.
Bluetooth®
Phone sound quality is poor.
The selected channel is locked. Enter the correct pass code
to unlock.
Call 1-866-635-2349 in U.S.A. or 1-877-438-9677 in Canada
to subscribe.
www.siriusxm.com for more information about the SiriusXM channel lineup.
unit.
Your subscription is updated. Press the volume knob to
continue.
• Search from the Bluetooth device again.
• Reset the unit.
• Make sure you have entered the same PIN code to both the unit and Bluetooth device.
• Delete pairing information from both the unit and the Bluetooth device, then perform pairing again.
• Check the
• Reduce the distance between the unit and the Bluetooth device.
• Move the car to a place where you can get a better signal reception.
( 13)
( 3)
[ECHO CANCEL]
setting.
( 14)
( 15)
( 13)
( 14)
ENGLISH
27
TROUBLESHOOTING
Symptom Remedy
Sound is being interrupted or skipped during playback of a Bluetooth audio player.
• Reduce the distance between the unit and the Bluetooth audio player.
• Turn off, then turn on the unit and try to connect again.
• Other Bluetooth devices might be trying to connect to the unit.
SPECIFICATIONS
FM
Frequency Range 87.9MHz — 107.9MHz (200kHz step)
Channel Space Selection 50kHz/200kHz
Usable Sensitivity (S/N=26dB) 8.2dBf (0.71μV/75Ω)
Quieting Sensitivity (DINS/N=46dB) 17.2dBf (2.0μV/75Ω)
87.5MHz — 108.0MHz (50kHz step)
The connected Bluetooth audio player cannot be controlled.
“PAIRING FULL” The number of registered devices has reached its limit.
“PLEASE WAIT” The unit is preparing to use the Bluetooth function. If the
Bluetooth®
“BT DEVICE NOT FOUND” The unit failed to search for the registered Bluetooth
“NOT SUPPORT” The connected phone does not support Voice Recognition
“ERROR” Try the operation again. If “ERROR” appears again, check if
“H/W ERROR” Reset the unit and try the operation again. If “H/W ERROR”
“BT ERROR PLS UPDATE” Update the Bluetooth firmware.
• Check whether the connected Bluetooth audio player supports Audio/Video Remote Control Profile (AVRCP). (Refer to the instructions of your audio player.)
• Disconnect and connect the Bluetooth player again.
Retry after deleting an unnecessary device.
DELETE PAIR)
message does not disappear, turn off and turn on the unit, then connect the device again.
devices during your device and connect manually.
feature.
the device supports the function you have tried.
appears again, consult your nearest service center.
[AUTO CNNCT]
. Turn on Bluetooth from
( 4)
( 18,
( 18)
Frequency Response (±3dB) 30Hz — 15kHz
Tuner
Signal-to-Noise Ratio (MONO) 64dB
Stereo Separation (1kHz) 40dB
AM
Frequency Range 530kHz — 1700kHz (10kHz step)
531kHz — 1611kHz (9kHz step)
Channel Space Selection 9kHz/10kHz
Usable Sensitivity (S/N=20dB) 29dBμ (28.2μV)
Laser Diode GaAIAs
Digital Filter (D/A) 8 times over sampling
Spindle Speed 500 rpm — 200 rpm (CLV)
Wow & Flutter Below measurable limit
Frequency Response (±1dB) 20 Hz — 20 kHz
Total Harmonic Distortion (1 kHz) 0.01 %
Signal-to-Noise Ratio (1 kHz) 105 dB
CD player
Dynamic Range 90 dB
Channel Separation 85 dB
If you have any troubles, try the following:
1 Check TROUBLESHOOTING 2 Reset the unit (
3) 3 Contact (USA only) Call: 1-800-252-5722 ( or ) visit: http://www.jvc.com
28
MP3 Decode Compliant with MPEG-1/2 Audio Layer-3
WMA Decode Compliant with Windows Media Audio
AAC Decode AAC-LC “.m4a” files
SPECIFICATIONS
USB Standard USB1.1, USB2.0 (Full speed)
Compatible Devices Mass storage class
File System FAT12/16/32
Maximum Supply Current DC5V
USB
MP3 Decode Compliant with MPEG-1/2 Audio Layer-3
WMA Decode Compliant with Windows Media Audio
AAC Decode AAC-LC “.m4a” files
WAV Decode Linear-PCM
Frequency Response (±3dB) 20Hz—20kHz
Input Maximum Voltage 1000mV
Auxiliary
Input Impedance 30kΩ
Version Bluetooth Ver.2.1+EDR/ Bluetooth 3.0
Frequency Range 2.402 GHz — 2.480 GHz
Output Power +4 dBm (MAX), 0 dBm (AVE) Power Class 2
Maximum Communication Range Line of sight approx. 10 m (32.8 ft)
Pairing SSP (Secure Simple Pairing)
Bluetooth
Profile HFP1.6 (Hands-Free Profile)
A2DP (Advanced Audio Distribution Profile) AVRCP1.4 (Audio/Video Remote Control Profile) PBAP (Phonebook Access Profile) SPP (Serial Port Profile)
1A
Maximum Output Power 50W×4 or
50W×2 + 50W×1 (Subwoofer = 4Ω)
Full Bandwidth Power (at less than 1% THD)
Speaker Impedance 4Ω—8Ω
Audio
Preout Level/Load (CD/USB)
Preout Impedance ≤600Ω
Operating Voltage (10.5V—16V allowable)
Maximum Current Consumption 10A
Operating Temperature Range 0°C to +40°C
General
Installation Size (W×H×D) 182mm×53mm×158mm
Weight
Subject to change without notice.
22W×4
KD-R960BTS
2500mV/10kΩ
KD-AR865BTS
4800mV/10kΩ
14.4V
(7-3/16"×2-1/8"×6-1/4")
1.2k
g
/
(2.65lbs)
KD-R860BT:
:
ENGLISH
29
Warning
• The unit can only be used with a 12V DC power supply, negative ground.
• Disconnect the battery’s negative terminal before wiring and mounting.
• Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to prevent a short circuit.
• Insulate unconnected wires with vinyl tape to prevent a short circuit.
• Be sure to ground this unit to the car’s chassis again after installation.
Caution
• For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer.
• Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during and shortly after use of the unit. Metal parts such as the heat sink and enclosure become hot.
• Do not connect the (black), or connect them in parallel.
• Connect speakers with a maximum power of more than 50W. If the maximum power of the speakers is lower than 50W, change the
[AMPGAIN]
• Mount the unit at an angle of less than 30º.
• If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red) to the terminal on the vehicle’s fuse box which provides

INSTALLATION / CONNECTION

12 V DC power supply and is turned on and off by the ignition key.
• Keep all cables away from heat dissipate metal parts.
• After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly.
• If the fuse blows, first make sure the wires are not touching car’s chassis, then replace the old fuse with one that has the same rating.
setting to avoid damaging the speakers. (
wires of speakers to the car chassis or Ground wire
21)
Basic procedure 1
Remove the key from the ignition switch, then disconnect the
terminal of the car battery.
2 Connect the wires properly.
See Wiring connection.
(31, 32)
3 Install the unit to your car.
See Installing the unit (in-dash mounting).
4 Connect the terminal of the car battery. 5 Reset the unit.
(3)
Installing the unit (in-dash mounting)
Hook on the top side
Orientate the trim plate as illustrated before fitting.
When installing without the mounting sleeve
Use only the specified screws. Using wrong
screws might damage the unit.
Flat or round head screws (not supplied) M5 × 8mm (M5 × 3/8")
Pocket
Bracket (not supplied)
Do the required wiring.
(31, 32)
Dashboard of your car
Bend the appropriate tabs to hold the sleeve firmly in place.
How to remove the unit
30
Wiring connection (for
KD-R960BTS KD-AR865BTS
Vehicle dashboard
Factory wiring
harness (vehicle)
Vehicle-specific Wiring Harness (separately purchased)
KD-R960BTS / KD-AR865BTS
Front output
Rear/subwoofer output
control adapter
Recommended
connection
Blue: To power antenna Blue/white: To amplifier
Brown
(Not used)
)
To the steering
wheel remote
Rear output Front output
Subwoofer output
Antenna terminal
Light blue/yellow
STEERING
WHEEL
REMOTE
Join the same color wires together.
Blue/white: Remote (200mA max.)
Orange/white: Illumination
Yellow: Battery 12V
1
*
Firmly connect the ground wire of the amplifier
to the car’s chassis to avoid damaging the unit.
Signal cord (not supplied)
Fuse (10A)
To the optional SiriusXM Vehicle Tuner (commercially available)
Ignition switch
JVC Amplifier
MIC (Microphone input terminal)
( 14)
( 11)
Remote wire
(not supplied)
1
*
For more information: Metra Electronics: www.metraonline.com Scosche Industries: www.scosche.com
Red: Ignition 12V
Black: Ground Gray: Front speaker (right)
Gray/black White: Front speaker (left) White/black
Purple: Rear speaker (right) Purple/black Green: Rear speaker (left)
Green/black
2
*
Car fuse block
Separate red wire
Make this connection if your vehicle factory wiring harness does not have “12V ignition switch” wire.
2
*
You can also connect a subwoofer speaker directly
2
*
using this lead without an external subwoofer amplifier. For setting,
21, 22
.
ENGLISH
31
Wiring connection (for
Vehicle dashboard
Factory wiring
harness (vehicle)
KD-R860BT
)
Front output
Rear/subwoofer output
To the steering
wheel remote
control adapter
Antenna terminal
Light blue/yellow
STEERING
WHEEL
REMOTE
Signal cord (not supplied)
Fuse (10A)
JVC Amplifier
Remote wire
(not supplied)
Microphone input jack
( 14)
1
*
Firmly connect the ground
wire of the amplifier to the car’s chassis to avoid
1
*
damaging the unit.
Part list for installation
(A)
Faceplate
(B)
Trim plate
Vehicle-specific Wiring Harness (separately purchased)
For more information: Metra Electronics: www.metraonline.com Scosche Industries: www.scosche.com
Recommended
connection
Blue: To power antenna Blue/white: To amplifier
Brown
(Not used)
Join the same color wires together.
Blue/white: Remote (200mA max.)
Orange/white: Illumination
Yellow: Battery 12V
Red: Ignition 12V
Black: Ground Gray: Front speaker (right)
Gray/black White: Front speaker (left)
White/black Purple: Rear speaker (right)
Purple/black
2
Green: Rear speaker (left) Green/black
2
*
*
Ignition switch
Car fuse block
Separate red wire
Make this connection if your vehicle factory wiring harness does not have “12V ignition switch” wire.
2
*
You can also connect a
subwoofer speaker directly using this lead without an external subwoofer amplifier. For setting,
21, 22
.
(C)
Mounting sleeve
(D)
Wiring harness
(E)
Extraction key
32
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
• “Made for iPod,” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod, or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance.
• iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.
• Lightning is a trademark of Apple Inc.
• Pandora, the Pandora logo, and the Pandora trade dress are trademarks or registered trademarks of Pandora Media, Inc., used with permission.
• iHeartRadio® is a registered mark of Clear Channel Broadcasting, Inc. in the United States and other countries. Such marks are used under license.
• Sirius, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. All rights reserved.
• Android is trademark of Google Inc.
• The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by JVC KENWOOD Corporation is under license. Other trademarks and trade names are those of their respective owners.
© 2014 JVC KENWOOD Corporation
0914DTSMDTJEIN
WHEN
IT
IS
NOT
REQUIRED
TO
PANEL USE
DETACH
FROM
THE
ATTACH
THE
MAIN
THE
FRONT
THE
PROVIDED
THE
CONTROL
UNIT.
CONTROL
MAIN
UNIT,
SGREWTO
PANEL
TO
GE4040
1-001 A
CONNECT
~CAUTION
OTHERWISE,
BLACK
WIRE
DAMAGE
({VGND)
TO YOUR
TO
GROUND FIRST.
UNIT
MAY OCCUR.
INCORRECT CONNECTION CAUSES SERIOUS PLEASE
CONNECT
METALLIC BODY OF THE
CAR
READ INSTALLATION/CONNECTION
GROUND
OR
CHASSIS
FIRST
@
DAMAGE TO THIS UNIT
MANUAL CAREFULLY.
CONNECT
CONNECT POWER CORD
OTHER WIRES
THE
UNIT
TO
U.S.A.
JVC
AMERICAS
CORP.
TO
OUR VALUED CUSTOMER
THANK YOU FOR PURCHASING THIS JVC PRODUCT.
YOU
WE WANT TO HELP
ACHIEVE A PERFECT EXPERIENCE.
NEED HELP ON HOW TO HOOK UP?
NEED ASSISTANCE ON HOW TO OPERATE?
NEED TO LOCATE A JVC SERVICE CENTER?
LIKE TO PURCHASE ACCESSORIES?
JVC IS HERE TO HELP!
TOLL FREE: 1 (800)252-5722
http ://www.jvc.com
Remember
Do
not
Caution
To
prevent electrical shock, There are no user serviceable parts inside. Please refer
We suggest that you register your product since it will enable
is
directly if it You
can register at www.register.jvc.com Please note that failure to register does not diminish any of your rights during the warranty period.
BT-50004-1
(0313)
ever necessary to correct a safety related condition
to
retain your Bill of Sale for Warranty Service.
attempt
to
service
to
qualified service personnel for repairs.
the
product
do
not open the cabinet.
PRODUCT REGISTRATION
yourself
us
to contact you
in
your product.
JVC
JVC
Americas
Corp.
RETAIL
PURCHASER
the
period
THIS
LIMITED
COMMONWEAlTH WHAT
WE
If
this
product
charge
to
the
service
centers.
authorized
service
cases. a technician
WHAT
YOU
Please
do
not
product
to
the
the
problem(s}
service
center.
service
representative
If
you
have
any
WHAT
IS
NOT
This
limited
1.
Products reasonable any
attachment
2.
Initial
installation,
3.
Operational
4.
Damage
5
Signal
reception
6
User
Removal
7.
Accessories:
8
Batteries
9
Products
10.
Loss
of
data
There
are
no
THE
DURATION
THE
DURATION INCONVENIENCE, LIMITATION. BREACH
OF
FITNESS
FOR
Some
states
these
limitations
vary
from
state
REFURBISHED WARRANTY,
For
customer
Enter
below
reference.
Model Purchase
(JVC)
shown
Will

warranty

that
THIS
to
below.
WARRANTY
OF
DO:
is
found
to
orrginal
owner.
Parts
used
center
will
come
MUST
DO
return
your
service
center, and a copy Service
locations
will
questions
COVER
provided
which
have
care,
or
if
not
provided
installation
adJustments
occurs
in
problems
Memory
(except
that
used
for
commercial
resultant
express
warranties
OF
ANY
OF
THE
OR
ANY
DAMAGE
TO
WARRANTY.
PARTICULAR
do
not
allow
or
exclusions
to
state.
PRODUCTS
PLEASE
REFER
use:
the
Model
No.
No.
date:
PUERTO
be
on a carry-in
FOR
product
of
require
concerning
EO:
been
repaired
shipment.
Rechargeable
from
IMPLIED EXPRESS
the
LIMITED
ONLY
FOR
PRODUCT
warrants
this
product
and
all
be
FREE
FROM
Warranty
DEFECTIVE
Period"}
("The
,--------------------------------------,
PARTS 2 YRS I LABOR 2 YRS : Car PARTS 1 YR I LABOR 1 YR:
IS
VALID
DNl
YIN
RICO.
defective
within
the
Such
repair
for
replacement
to
your
WARRANTY
to
please
the
proof
can
clear
by
JVC
subject
or
with
and
covered
and
far
Devices/Video
purposes,
malfunction
except
WARRANTIES,
WARRANTY
OTHER
DAMAGES,
TAPES,
RECORDS
ALL
PURPOSE,
exclusion
may
not
CARRY A SEPARATE
TO
THE
and
Serial
warranty
and
replacement
are
warranted
basis.
Color
and
either
SERVICE:
retailer.
to
package
purchase
be
obtained
to
JVC
not
abuse,
by
products,
from
the
Owner's
to
act
due
to
Pick-up
including,
of
hard
listed
OR
AND
ARE
LIMITED
incidental
to
which
televisions
Instead,
to
the
Product,
cover: accident,
anyone
or
of
God, line
TubesiCCD
are
drive
above.
INCLUDING
HEREIN.
WHETHER
DISCS)
you
1700
WARRANTY,
is
located
home
the be
sure
of
also
access
your
does
to
serviced
the
removal in due lures
Batteries
as
EXPRESS
of apply
REFURBISHED
No.
MATERIALS
THE
FIFTY
period,
services
only
for
with a screen
repair
the
TV
return
it
carefully,
verrfy
purchase
from
our
website
product.
please
alteration.
other
than a service
if
the
model
cabinets
or
Manual,
normal
and
cosmetic
power
surge;
covered
for
but
not
or
other
THE
JVC
SHALL
DIRECT,
RESULTING
IMPLIED
WARRANTIES,
TO
THE
WARRANTY
or
consequential
This
warranty
JVC
AMERICAS
Valley
Road,
http:llwww.jvc.com
THIS
PRODUCT
WARRANTY
either
parts
your
contact
mounting
Image
limited
WARRANTY
PURCHASED thereof,
AND
All
other
(50)
UNITED
JVC
will
repair
shall
be
the
remainder
there
or
product
preferably
date.
http/lwww.jvc.com.
our
modification.
or
serial
maintenance,
damage:
Sensors
90
days
from
to
rental
data
storage
IMPLIED
NOT
INCIDENTAL
FROM
damages
gives
you
Wayne,
WARRANTY
on
the
rear,
Serial
Name
IN
except
as
WORKMANSHIP
audio
ARSENAL
car
audio
STATES,
or
replace
rendered
by
JVC
of
the
Warranty
size
of
37"class
remove
and
return
to
the
JVC
authorrzed
in
the
original
Please
call1-800-252-5722
Customer
Care
tampering,
facilrty
authorized
number
has
systems.
video
are
covered
the
date
of
device:
WARRANTY
BE
LIABLE
FOR
OR
CONSEQUENTIAL
THE
USE
OF
INCLUDING
PERIOD
SET
or
limitations
specific
legal
CORP.
New
Jersey
07470
DOES
NOT
INFORMATION
bottom
or
side
No
..
of
dealer:
U.S.A.
set
forth
below
from
the
series
products
THE
DISTRICT
defective
parts
during
normal
Period.
or
Center
been
and
for
purchase}:
OF
ANY
THIS
THE
FORTH
rights
APPLY. PACKAGED
All
greater
qualify
it if
it
cannot
servrce
packaging, If
of
and
to
your
product at
800-252-5722
negligence,
by
JVC
to
altered,
tampered
audio
head
90
days
from
MERCHANTABILITY,
LOSS
OF
(INCLUDING,
PRODUCT,
WARRANTIES
ABOVE.
on
how
long
and
you
FOR
DETAIL WITH
the
cabinet.
ONLY
TO
date
of
original
OF
COlUMBIA
with
new
or
rebuilt
business
hours
products
may
for
in-home
be
repaired
rn
center
nearest
include a brief
locate
the
nearest
qualifies
for
misuse.
faulty
render
such
service,
with,
defaced
cleaning;
the
date
of
IS
USE
an may
LIMITED
OF
THE
WITHOUT
OR
ARISING
OF
MERCHANTABILITY
implied
warranty
also
have
OF
REFURBISHED
EACH
REFURBISHED
Retain
this
information
THE
ORIGINAL
purchase
AND
equivalents
at
JVC
authorized
be
brought
service.
In
your
home
you
If
shipping
description
JVC
authorized
in-home
service,
installation.
or
if
or
removed:
purchase:
TO
PRODUCT,
OUT
OF
ANY
lasts,
other
rights
PRODUCT
PRODUCT.
for
Printed
in
for
IN
THE
at
no
to a JVC
such
the
of
the
lack
of
affixed
to
AND
so
which
future
Indonesia
CANADA
JVC
CANADA
INC.
.JVC
JVC
CANADA
INC.
Canada
by
maintenance
1.
To
Obtain
(a)
J
VC
wit
h
(b)
The a
uth
2.
Limitation: Thi
s W
(
a)
R
epa
c
onn
gri
ll
s
av
(b)
Any m
is
in
su
(
c)
Any fol
lowi
(d
)
Any any
pe
rs
(
e)
An
y
defa
(
f)
Ma
(g)
Co
n
(h)
An
y
Re
gu
(i
) Any
r
en Part L
abou
(j)
A
ny
by
the
(k
)
Pr
od
"li
quida
(I
)
Any ot
her
(m)
F
OR
W
ar
i
nte
for
Product
Registration
We
su
g
ges
co
nditi
on in
For
customer
Enter
below
re
fer
en
ce.
Model Pur
JVC
,
Warranty
pr
o
du
proof
JVC
or
ized
arranty
ir
or
e
ction
s,
s
pea
ers
, a
defects
us
e,
abusive
ffi
c
ient
de
f
ec
ng
J
VC
par
ty
onn
el. JVC ced.
in
tenance
ver
sio
JVC
l
ations
JVC
tal, or
s ..
..
r
.
.. JVC
ori
uct
purchased
t
or". defects
events
AUTO
ranty d
r
fe
ren
the
rem
t th
at
yo
ur
the
No
c
ha
se
Mode
(hereafter
and
sold
from
any
defect
Service:
ct req
ui
ring
of
purch
ase
product
mus
JVC
Servi
shall
not
replacement
c
ords
,
ant
k
er
co
n
es
nd
all
a
ccesso
cau
s
ed
ope
care.
t
caused
or
the
i
nstr
uctions
produ
ct
tamp
o
ther
than
product
s on
modified
or
,
clean
i
n
to
foreign
produ
ct with
10.
products
us
di
s
play
purpose
1 y
ea
r (ex
cep
90
da
ys
produ
ct
whi
ginal
pur
c
ha
fr
caused
beyond
PRODUCTS
oes
not cover
ces, c
leanin
o
va
l or r
ei
yo
u reg
ister
p
ro
du
c
t.
Yo
use
:
l
No.
and
.. date:
Warranty
called
by
an
auth
s
ser
v
ic
.
t
be
br
o
ce
Ce
n
tr
app
ly
to:
of any
e
nna
s, du
,
pr
oj
ec
ti
ri
es
.
or
repai
rs
r
ati
on, neg
rep
ai
rs
in
ered with,
JVC
or a
wh
ich
the
rem
ove
ng
or
pe
riod
or
dom
out
th
e
ed for
co
s.
t vid
eo
ch
h
as
been
s
er.
om
"o
ut
by
fi
r
e,
fl
oo
the
control
elim
g
of
head
n
st
al
la
t
ion
TE
L
(90
you
r
produ
u
can r
Ser
ial
ap
o
in
material
e
must
ug
ht in f
e.
cab
i
st
on
sc
r
equ
lige
re
q
uire
t
he
ope
ad
ut
ho
se
d.
ic
es
ti
c vol
Can
m
me
h
ead
si
de
d,
of
in
a
tio
,
ad of
5)
ct s
egiste
No.
plies
only
"
JVC")
rized
JVC
be
pr
or
service
ne
t
s,
batteri
c
over
s,
re
en
s,
ired
as
nce,
improp
d
as
rat
ion
ju
st
ed
riz
ed
JVC
rial n
umber
check-up
tag
a
di
an
Elec
rc
ial
or
-
90
res
old
Ca
nada
li
gh
tn
i
JVC.
n
of
ca
ju
s
tmen
th
e
uni
6070
kestrel
6
70
-
3381
in
ce
r at
http
which
to
gives
the
dealer.
and
workm
ese
nt
ed
to
es
, p
kn
obs,
pr
o
je
c
a
re
s
ult er
a
res
ult
man
ua
or r
epair
Se
rvi
has
e or freque
tri
cal Saf
institution
day
s)
a
nd
no l
",
"
ba
n
krup
ng,
power
r s
ta
tic or el
ts.
or
t for r
epa
Road
FAX
http//www
it
will
en
://
www
is
located
WARRANTY
PRODUCT
sp
ti
of
l ce
onger
lab
(905
ab
follow
JVC
toget
an
lates,
e
ak
on
sc
of
us
e
and
not
ed
by
Centre
be
en
nc
ety al,
tcy
s
ur
ec
our
ir.
JVC
,
Missi
.jvc
le
.j
v
c.
eithe
a
nsh
h
er
r
y.
ow
ge
cos
)6
us to
ca/
dis
tr
ibuted
ing
ex
press
war
rants
ip s
ub
ject
3.
er
4.
ee
n
5.
/o
r
WARRANTY
Product Projection
Colou 0-I LCD
*In-Home
Where
responsibility and and
ne
d
Receivers separately
"
or
Aud
, or
AC Headphones lamps
tr
ical
Wood
t
All
CANADA
s
aug
a,
Ontario,
70
-
7244
.ca
E-mail
cont
act you
www/S
u
ppo
r on the re
ar,
Serial
Name
that
to
Standards
If
a
appl
the
such Exclusion
Th
is
JVC
or
hi
e
xt
e
Disclaimer To
t
for
or
an
i
nco
LA
TV
all fro
io
Adapters,
Other
INC.
Service
servi
dir
rt/
botto
in
Canada
warranty
this
JVC
the
follo
w
:
ny
def
ects
shou
i
cabl
e te
rm
purcha
se
r for
def
ects are
of
All
wa
r
ra
nty
cons
for
J
VC
p
ro
s,
its
or
th
ei
nd
or
enl
ar
of
he
ext
ent
the
los
s
of
ti
me or
y o
th
er
in
direc
nven
ien
ce.
TERM
TV
In
-
r
TV
In-Hom
Rear
Proj
ec
In-H
o
me
se
r
vi
ce
it
is
not
a
vai
and
cost
s
as
soc
m
th
e c
lo
ses
a
nd
Home
.
Front
"ARSENAL"
Re
,
Mi
Con
e
Spe
akers
Ca
t
egories
L5T
1
SB
toll
fr
ee# 1-
ce@
j
vc
.
ca
ecll
y if it is
Warr
a
nt
y.
aspx
m
or
s
id
e
No
.:
of de
al
er:
by
for e
produc
ing
s,
n pa
du
Oth
d
ucts
r
agen
ge
this
Con
law
us
(VAliD
Ho
me
e (25"
tion
Se
to
lab
e
xpense
iated
t
P
ro Ser
mo
te
cro
p
Can
ever
of
the ca
JVC ac
h n
t
t
erms
ld
be
ecessa
rts or lab
e to fa
er
tit
utes
and
t or
wa
se
que
perm
e
of
t,
i
nc
Serv
and
In-
rv
i
ce
be p
le,
th
with
J
VC
S
peaker
j
ec
ti
on
i
es
con
hon
es
ad
a
800-96
necess
Ca
ew
is
f a
fou
ry repa
ult
E
xpress
the
no em
rra
n
i
ts its i
den
FROM
Ho (25"
rov
e
f
or
Aut
and
trol
a
bin
e
nada
Inc.
JVC
ree
,
under
nd
conditions:
nd
rna
ir
ou
r
when
y
material
entir de
al
er
pl
o
ye
nty
on
tial
Damage
JVC
di
produ
c
tal
or
ice
a
bov
e)
me
Servi
and a
ided
where
purch
th
e
prop
th
e de
hori
ze
s
pur
ch
Car
s, nd
Projector
4-
2
650
ary
to
t.
Retain
product distri
norma
J
VC
pr
oduc
s
sh
all
be
mad
JVC
a
ck
or
wor
kmansh
Warranties
e e
xpr
ess
war
or
se
rvi
ce
e i
s.
or a
re
beh
al
f of
J
VC
:
sc
laim
s a
ny
t,
tr
an
spo
rt
c
on
se
q
uent
THE
DATE
Pa
(Yea
ce
bo
ve)
avai
lable.
a
ser
mu
st
ass
er p
ac
k
liv
ery of the
d
Serv
i
ce
Centre
ase
d
90
correct
a
safe
this
informa
bute
l
us
e a
t within
e
at
no
n
ow
l
edges
ip.
:
ra
nty g
cen
t
re
pe
auth
or
ize
respons
at
ion
costs
i
al
da
ma
OF
PURCHASE)
rts
r
s)
1
u
me
the
in
g, sh
ipme
equ
i
pme .
2 2
days
5
1
ty
r
elated
ti
on
for
d in
nd
the
cos
iven
rso
d to
ibili
.
ge or
L
ab
(
Ye
nt to
90
fu
t to
t
ha
t
by
nn
ty
our
ar
s)
1
nt
days
5
1
ture
el
JVC
C
AN
AD
A
I
au C
anada
en
tre
1. Pour (a)
(b
2.
R Cett (a
(b)
(c)
(d)
(e) (
f)
(g) (h) (i)
(j)
(k) (I)
Enregistrement
N
ous
co
r
rige
Pour
Ent
re
z
i
nfor
ma
NC.
par
ti
en
no
rmal
obte
ni
L
es
p
rod
u
ave
c
Ia
pre
) Le pr
odu
it
de
serv
ic
e
es
tr
ic
ti
on
s:
e
ga
r
ant
ie ne s'a
)
Repa
rat
io
pan
ne
au
ava
de
protecti
hau
tp
a
rle
pro
j
ec
ti
on
To
us
de
f
au
uti
li
satio
n ab
incorrec
te
Taus
de
f
au
a
!
'omiss
ion
d'i
nst
ruct
Tou
t pr
odui
en
tr
ep
rise
ser
vice
au
T
ou
t
pro
d
ou
en
l
eve
L'
entre
ti
en
La
conver
domesti
que.
Tou
t
pro
duit
co
nfor
me a
Pou
r
tout
ins
ti
t
ut
i
on
Pi
eces.
..
M
ain
d
'o
euvre
T
ou
t
pro
d
pr
op
ri
ete
P
ro
duit
ac
"
fa
il li
te"
ou d'
Tout
do
mma
un
e
sur
t
ens
JVC
.
vous
conse
r
un
pr
obl
!'utilisation
ci
-dess
ous
tions p
ou
No
.
de
model
Date
d'acha
JVC
r
it
n ou r
ur.
io
t uit .
s
produit
uit de
illons eme
r
,
un
s J vu JVC
JVC
on, et
ts
.
ts
n.
t
J
qu
or
, l
es
io
ux
n
elles
he
ge
i
on
du
le
refe
t:
( ci-apr
et
de
tout def
service
VC
e
d'a
doit aut
emplac
nt.
cordons
bou
ec
r
ans
to
usl
occ
asi
us
i
ve
oc
casio
de
suivre
VC
e
J
VC
i
se
JVC
J
VC
ver
n
a
une
JVC
no
r
,
..
... JVC l'a
ch te
a
"l
un
"liq cause ou tout
produit
d'
li
e
des
n
um
ren
e:
La
es
v
end
u
necess ch
a
t.
etre
orise.
pp
li
que
em
t
ons
,
de pro
es
ac
onnes
,
ma
uvaise
nn
l
es
alte
re
,
ou
un
.
don
t
le
if
ic
a
tio
fr
eq
n'a
ya
nt
ms
electriques
ut
ili
se
de
loca 1 An (E 90
J
ours
a
yant
ete
et
e
ur
or
'ex
te
ri
ui
dateu
par
au
TEL
enregis
a
Ia
se
clients:
ero
de
ce
future.
ga
ra
nt
ap
pel
pa
r
au
t
de
ga
ita
nt
appo
pas
aux
en
t de t
de
raccord
couver
je
ct
c
esso
ou
, n
es
ou
recom
aj
us
te
ce
ntre
nu
mero
ns
pe
ue
n
ce
pas
a
des
tion
ou
xc
ep revendu
igi
na
eu
r
du
r"
le
f
eu
t
re
evenement
(
905
t
rer
cur
ite
mode
ls'
app
lique
e
"J
VC
un
d
eta
mat
er
iel
r
ant
ie:
un
se
rv
ice
rt
e pour servi
:
ou
t c
,
anten
ts
de
hau
i
on.
pr
otect
i
res.
r
epar
ations r
eg
li
ge
nt
r
eparat
ion
man
da
ou
re
pa
re
de
serv
de
se
ri
od
i
ques
ou
un
e
le
si
gne
Ca
nad
fi
ns co
mm
utili
se
te
l
es
tetes et
l
Canad . une i
non
607
)
67
0-
votre
pr
odu
de
vot
re
le
et
le
seulem
")
en
illa
nt
et
de
do
it
ce
abi
n
et
n
es
tp
ar
e
ur
equ
e
et
/o
s
requ
tio
ns
par t
ice
d'e
rie
a
ete
et ne
ten
s
ion
d'identif
ien
nes
ercia
a
des
vi
deo­qui n'est a",
pro dat
ho
rs du
0
kestrel
3381
htt
it,
ca
pro
dui
n
ume
ro de
GARANTIE
ent aux
P
RO
on
ce
Ia
g
ar
a
au
tor
ic
at
p
re
ez
un
ri
cones
ec
ran
suite
ut
su
manue aut
re
e
tien
re.
tra
ngere
a
ti
on
A)
,
d
'et
90
j
ours
lu
s Ia
ant
d'
un
ec
co
ntr
JVC
ad, Mi
(905
www il
nous
serie
nt
i
se
.
i
on
so
sente
e
centr
es
,
de
de
a
une
il
ization
it
e
l
ou
de
m
od
i
.
ou
qu
i
. al
age.
)
u
ne
lair
,
ole
de
CANADA
ss
is
)
670
.jvc.ca
permett
p
ou
v
ez
qu
i
se
JVC
fabr
et
re
ch
,
batte
.
housses
l
eu
r.
s d'
ises
u une
ises
du
ou
t
ntr
alte
tt
oyage
e
ic
(CS
l
es
fi
ns
p
ven
io
n,
Ro
F
AX
p://
r
t.
Vous
DUIT
S d
ie ex
pres
J
VC
vo
us
res
e
3.
4.
5.
f
ie
CONDITIONS
Produi
~ c
Ecrans TV proj Ec
" S' Ia que det
Recep sep de
A
dapt
D'eco Encei To
auga
,
On
-7
24
4 Servi
E-
ma
ra
de
vo
us
insc
tr
ou
ve s
N No
is
trlbu
es
se su
us g
aran
er
ve
de
(m)
PO
UR La gar s
ta
t
es
l
a l'
enlevement
Cri
teres
Si
un
prod applicab sans
coOts
d'
reuvre
cau
sees
E
xcl
usi
C
ette
gara
JV
C
pou
det
ai
ll
ant
c
ett
e
ga
De
negation
D
ans
Ia
pou
r perle
tr
an
spor
a
cc
i
de
n
t
rans
de
de
TV
ect
i
rans de L
Se
rv
ice
a
il
n'y a p
as
respo
nsab
tau
s
les
a
il
lant
JVC
t
eu
rs et
arement, P
Serie
"A
a
teu
rs
ute,
Mi
nte
a
u
tes
le
s
INC.
tario,
L
ce
il:
se
r
vi
ce@
vous
con
rir
e
a
http
oil
a
l'a
o.
de
se
rie
m du
re
au
Can
ad
iva
n
te
p
tit
qu
e
s
mo
dali
LES P
an
lie
ne
iq
ues
ou
juste
m
ents
:
u
it
JVC
l
es
,
l
es
add
iti
lor
sque
pa
r une def
on
de fout
n
tie
cons
r
les
produ
ou
d'un
r
antie
au
des
mesure
de
t
emps
t
ou
to
ut
tel
et
conseq
DE
GARANT
project
ion
Coul
eu
r
Se
on
a
rriere
CD
Service
dom
ici
le
de
service
i
lite
et
l
es
co
ots
as
s
auto
r
ise
Ha
uts
ro
1e
ct
R
SE
NA
L"
AC,
T
elec
crophones
Cone
en
autres
cat
5T
1
SB
Can
to
ll
fr
ee#
j
vc.ca
t
acte
r d
irec
://
ww
rrie
re
.
en
:
ve
nde
ur:
a p
ar
ou
r
ce
pr
tes
ROD
cou
el
ec
et
ou
a
s'
ave
r
epa on
nels
JVC
ec
es ti its
service
nom
dom
pe
rmi
aut
Serv
rvice
D-ILA
a
fo
u
JVC
coot
ocies
le
pl
-P
a
eur
omman
et
Bo
is
eqo
ad
1
-800-964
tem
w
.j
v
bas
JVC
to
odui
et c UIT
vre
tri
ques l
es
Ia
r
at
r
econn
t
uos
a
tue
JVC.
de
m
se
ou
re
dom
ue
nt.
IE (
i
a
D
omici
rni
dispon
s
po
a
us
rle Avan
Lamp
ri
es
a
ent
c.c
ou
Canada
ut n
t
ondition
S
D'
p
as
coO
re
in
rait
defe
i
ons
a
l'a
ite
ut
r
es
l
'e
nt
Nu
d'ent
JVC ages
par
d'
us
m
VA
L
ce
a
Do
mi
Se
rvi
par
ur
un
Ia
li
vr
ore
s
urs
a
t et A
de,
e
si ja
a/
www
sur
ouve
au
es
t
de
AUT
O
!'
e
li
de
Ia
ts
de
stal
la
ti
ctu
nec
e
ss
ch
ete
a1t
que
de
m
ga
ra
ie
re
g
l
rep
ret
ien n'
.
indi
Ia
to
i,
age
de
age
ABLE
D
om
ici
cile
(
25
ce
a
Domic
le
(2
5"
un
d
et
ible
a
e
mball
ai
son
pour
un
ch
etes
udi
Casque
de
Pr
-2
650
ma
/
Sup
le
cote
In
c.
p
ro
duit
gag
e,
s su
iv
an
MOB
IL
E
m
ina
t
ion
voi
t
ur
e.
le
ma
in
d'
on
de
l'unite
eux
,
se
air
es
se
ur
po
ur
l
de
tel
ls
at
eri
el
ou
nt
i
es
exp
ar
antie
expr
rese
ntant
est
rec
ts:
JV
C
nie t
ses
p
ro
ou
inconvenien
a
PARTIR
le
"
et plus)
i
le
et
pl
us)
ai
lla
nt
di
proxi
mite,
age
ad
de
l'eq
ui
peme
serv
i
ce
o d'
Au
to
oie
cteu
r
is
elle
es
por
t/
Wa
de
!'a
rm
J
VC
distribue
so us
ut
ili
tes:
d'
i
nte
r
fer
net
t
oy
a
ce
uvre
asso
pour
t
on
l
es
cond
ront
effe
es
pie
ces
defectuos
de
fabr
r
ess
es :
ess
do
ou
emp
a
uto
r
is
e
a
ou
te
res
duit
s,
des t i
nd
DE
LA
DATE
Pi
eces
.
(A
nn
eesl
1
spon
i
ble.
l'
ac
h
eteur
equat.
!
'exped
nt
che
d'ent
ret
ie
2 2
90
Jours
5 5 1
t n
ece
s
saire
rranty.aspx
o
ir
e. C
ons
sa
ti
ences
ge
de
ci
es
r
epa
it
ions
ctues
et
Ia
ites
icat
i
on
nn
ee
l
oye
pro
pons
coo
ir
ec
D'A
Ma
I
(Annees)
doit
ition, ainsi
z et
dep
n
90
po
e
rv
on
ma
d'
lon
ab ts
t,
in
ass
ez
tete
a
rati
so
.
pa
·D
uis
Jo
ur
et
,
on.
in nt
r un ger
il
i
te
de
CHA
'oeu
1
ume
ur
1
c
es
T)
ver
r
le
s
Loading...