Page 1
John Deere AutoTrac™
Control ler
PFP11790
Page 2
About This Document
This User Guide will help you learn how to perform common tasks with
your John Deere AutoTrac Controller. It is a supplement to the controller
Operator’s Manual.
Read the Operator’s Manual for the following information:
• How to operate your controller safely
• Theory of operation
• Initial setup
• Diagnostics
Copyright © 2011 Deere & Company. All Rights Reserved. THIS MATERIAL IS THE
PROPERTY OF DEERE & COMPANY. ALL USE AND/OR REPRODUCTION NOT
SPECIFICALLY AUTHORIZED BY DEERE & COMPANY IS PROHIBITED. All information,
illustrations and specifications in this manual are based on the latest information available
at the time of publication. The right is reserved to make changes at any time without notice.
Page 3
User Guide AutoTrac Controller
User Guide
Section Contents
AUTOTRAC CONTROLLER CALIBRATION...................... 2
Calibration Procedure ........................................................................... 2
Wheel Angle Sensor (WAS) Calibration ............................................... 3
Valve Calibration .................................................................................. 4
GS3 2630 Display
1
GS3 2630 Display
Page 4
User Guide AutoTrac Controller
GreenStar
Guidance
Guidance
Settings
AutoTrac Advanced
Settings
Change
CAL
User Guide
John Deere AutoTrac Controller Calibration
The John Deere AutoTrac Controller calibration procedure must be
completed with a passing status prior to using AutoTrac.
Calibration Procedure
• Calibration procedure will require a large, open, level surface to
complete the required steps.
• Calibration procedure will require the tractor to be driven slowly
at full throttle for approximately 2 to 5 minutes to bring hydraulic
fluid to operating temperature before beginning calibration procedure.
IMPORTANT: Read all instructions before calibrating the AutoTrac Controller.
Calibrate AutoTrac Controller without an implement
connected to the tractor to avoid damage to the tractor and/or
implement.
1. Turn AutoTrac Controller Master Switch to ON.
2. Menu ..........................................................................
3. GreenStar ..............................................................
4. Guidance ........................................................................
5. Guidance Settings ...........................................
6. AutoTrac Advanced Settings ..
7. Navigate to Page Three using Next Page button .......
8. CAL ...................................................................
GS3 2630 Display
2
GS3 2630 Display
Page 5
User Guide AutoTrac Controller
CAL
Wheel Angle
Sensor Calibration
User Guide
Wheel Angle Sensor (WAS) Calibration
1. Below Wheel Angle Sensor Calibration select
CAL button.
2. Next .............................................................................
NOTE: Machine may need to drive forward slowly to allow the wheels to
reach their full range of motion.
3. Turn wheel until LEFT stop.
4. Next .............................................................................
5. Turn wheel until RIGHT stop.
6. Next .............................................................................
7. Turn wheel back to CENTER with wheels straight.
NOTE: It is recommended to pick a point in the horizon ahead of
machine, slowly drive forward while adjusting steering wheel until driving
in a straight line.
8. Next .............................................................................
9. Drive in straight line at or above 16 km/h (10 mph) until
NOTE: It is recommended to pick a point in the horizon ahead of
machine, slowly drive forward while adjusting steering wheel until driving
in a straight line.
10. Next .............................................................................
calibration is complete.
GS3 2630 Display
3
GS3 2630 Display
Page 6
User Guide AutoTrac Controller
CAL
Valve Calibration
User Guide
Valve Calibration
1. Under Valve Calibration select CAL button .............
2. Next .............................................................................
3. Begin moving forward in the lowest gear at the maximum RPM.
4. Next .............................................................................
5. Wait for calibration to finish.
6. Repeat steps 4 and 5 until three left turn and three right turn
calibrations have been completed.
7. Turn steering wheel back to center with wheels straight.
8. Next .............................................................................
9. To exit calibration screen select Accept ..........................
GS3 2630 Display
4
GS3 2630 Display
Loading...