Jensen VX-4025 Quick Start Guide

VX4025

Installation / Quick Start Guide

Complete operation manual is

online at www.jensenmobile.com

Note: There is no operation manual in this package

What’s in the Box

following items are supplied

The
with

the VX4025:

• VX4025HeadUnit

• TrimRing

• HardwareBag

• Power/SpeakerOutputHarness

• RemoteControl

• ExternalMicrophone

• Installation/ Quick Start Guide

WARNING!Neverinstallthisunitwhereoperationandviewingcouldinterferewith
safedrivingconditions.

The following tools and supplies
are needed to install the VX4025:

• Torx type, flat-head and Philips

• Wire cutters and strippers

• Tools to remove existing radio (screw

• Electrical tape

• Cr

• Volt meter/test light

• Crimp connections

• 18 gauge wire for power connections

• 16 – 18 gauge speaker wire

Tools and Supplies

screwdrivers

driver, socket wrench set or other
tools)

imping tool

DASHBOARD

TAB

Step 1-b

Step 1-c

Step 2

Step 5-c

Steering Wheel Control (SWC) Ready

The recommended SWC Interface is the PAC SWI-RC steering wheel control adapter.

SWI-RC installation hints:

1. Set "Radio Select Switch". S

2. Programming - Use the Pioneer/Sony/Other radio function mapping order for Jensen branded head units.

3. When programming the SWI-RC, if a function is not supported (or not desired), then the function MUST be skipped as per
the PAC SWI-RC instructions.

4. The SWC functions MUST
instructions.

et the SWI-RC to position 7 - "Pioneer/Sony/Other".

also be programmed in the correct order per the PAC SWI-RC radio function mapping order

Disconnect the Battery

• To prevent a short circuit, be sure to turn off the ignition and remove the negative (-) battery cable prior to installation.

NOTE: If the VX4025 is to be installed in a car equipped with an on-board drive or navigation computer, do not
disconnect the battery cable. If the cable is disconnected, the computer memory may
use extra caution during installation to avoid causing a short circuit.

Replacing the Fuse

•

When replacing the vehicles Radio fuse always use the proper rated replacement fuse. Using a fuse with an improper rating
could damage the unit and cause a fire.

ISO-DIN Installation

The VX4025 is designed to fit into a 2.0 DIN dashboard opening. The unit has threaded holes in the chassis side panels which may
be

used with the original factory mounting brackets of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to
mount the radio to the dashboard. Please consult with your local car stereo specialty shop for assistance on this type of
installation.

1. Remove the existing factory radio from the dashboard or
center console mounting. Save all hardware and brackets as
they will be used to mount the new radio.

2.

Remove the factory mounting brackets and hardware from the
existing radio and attach them to the new radio.

CAUTION! Do not exceed M5 X 6MM screw size. Longer
screws may damage components inside the chassis.

3.

Place the radio in front of the dashboard opening so the
wiring can be brought through the mounting sleeve. Follow
the wiring diagram carefully and make certain all connections
are secure and insulated with wire nuts or electrical tape. After
completing the wiring connections, plug the
the mating socket on the rear of the chassis. Turn the unit on
to confirm operation (vehicle ignition switch must be
the unit does not operate, re-check all wiring until the problem
is corrected.

connector

“ON”). If

into

be lost. Under these conditions,

4.

Mount the new radio assembly to the dashboard or center
console using the reverse procedure in step 1 above.

CAUTION! Be careful not to damage the car wiring.

NOTE: It is the end-users responsibility to install and operate this unit in a manner in accordance with local, state and federal
laws. The PARKING BRAKE wire MUST BE CONNECTED as directed in the manual.

Using the Cosmetic Trim Ring

A cosmetic trim ring is supplied with the head unit for installation
flexibility. This unit will fit into most import dashes with little or
no modification to the dash board/cavity. Some US domestic
vehicle dashes will accept a Double-DIN chassis, but there is
usually a small gap between the radio and dash piece after
installation is complete. In this case, use the trim ring to conceal
any gaps that may be present.

NOTE: For proper operation of the CD/DVD player, the chassis must be mounted within 30° of horizontal. Make sure the
unit is mounted within this limitation.

2

WHITE/PURPLE

WHITE/BROWN

BROWN/BLACK SWC GND

PINK

GREEN/WHITE

BRAKE (-)

REVERSE (+)

SWC A

SWC B

BLACK

RED

ORANGE

BLUE

GROUND (-)

ACC / IGNITION (+)

TFT DIMMER (+)

POWER ANT & AMP (+)

PURPLE/BLACK

GREEN

GREEN/BLACK

YELLOW

RIGHT REAR SPEAKER (-)

LEFT REAR SPEAKER (+)

LEFT REAR SPEAKER (-)

BATTERY 12V (+)

WHITE

WHITE/BLACK

GRAY

GRAY/BLACK

PURPLE

RIGHT FRONT SPEAKER (-)

RIGHT REAR SPEAKER (+)

LEFT FRONT S

LEFT FRONT SPEAKER (+)

RIGHT FRONT

YELLOW RCA - REAR CAMERA

BLACK DIN CABLE - SiriusXM

BLACK 3.5MM - BT MICROPHONE

BLACK 1MM WIRE - BT ANTENNA

SPEAKER (+)

PEAKER (-)

SPEAKER (-)

SPEAKER (+)

QUICK START GUIDE

Turning the Unit ON or OFF

Press the front panel volume knob to turn the unit ON. Press and hold the volume knob > 1 second to turn the unit OFF.

Selecting an Audio/Video Source, Phone, Steering Wheel Controls, Backup Camera or Pandora

To select a source:

1. Press the front panel MENU button or touch the SRC icon to view the Main
Source Menu

MENU

Button

2.

Touch the desired source icon on one of the two main menu screens. Screen 1 of 2: Disc, Radio, USB, AV-IN1, Settings,
Phone or Camera. Touch Next
Pandora or SiriusXM (SXM).

at the bottom of the screen to access Screen 2 of 2: Steering Wheel Controls (SWC), AV-IN2,

Volume Adjustment / Turn On Volume

To increase or decrease the volume level, rotate the rotary encoder knob. The unit’s front panel screen will display the volume level
for 2 seconds. The volume level ranges from 0 to 50. To set the Turn-On volume, press and hold the rotary encoder knob 1 second
while the green volume bar is displayed after setting the desired volume level. You will hear 2 beeps to confirm the new Turn-On
volume level.

Audible Beep Conrmation

An audible beep tone confirms each function selection. The beep tone can be disabled through the Setup menu.

Muting the Audio

Press the front panel volume knob ( ) to mute the audio from the unit. Mute icon is displayed on the LCD screen. Press the front
panel volume knob again to restore the audio volume to its previous level. Adjusting the volume or using any of the audio setup
features cancels the mute function.

Equalizer Controls

Equalizer (EQ): Adjustment can be made after entering one of the audio/video sources (Disc, Radio, USB, AV-IN or SXM).
Touch the Equalizer (EQ) icon to view the Equalizer Control Screen to select a desired preset setting (Optimal, Classic, Rock, Jazz,
Techno or Pop), Flat setting, custom User setting, make adjustments to the audio Balance and Fader levels or to turn the Loudness
option ON or OFF. Touch the SRC icon to return to the current source.

Voxx Electronics Corporation

Hauppauge, NY 11788

Technical Assistance: 800-323-4815

www.jensenmobile.com

© 2015 Printed in China