Jensen JE1908 User Manual

JE1908

19” HD FLAT PANEL LCD TV

OWNER'S MANUAL

SAFETY PRECAUTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS

* SEE REAR OF UNIT FOR GRAPHIC SYMBOLS *

RISQUE DE CHOC ÉLECTRIQUE NE

PAS OUVRIR

The lightning flash with an arrowhead within a triangle alerts you to uninsulated dangerous voltage within the product's enclosure that could cause an electric shock.

The exclamation point within a triangle alerts you to the presence of important operating, maintenance and servicing instructions in this user’s manual.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. DO NOT PLACE OBJECTS FILLED WITH LIQUIDS ON OR NEAR THIS UNIT.

CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.

The symbol for Class II (Double lnsulation)

PLACEMENT INFORMATION

• Do not use this unit in places which are extremely hot, cold, dusty, or humid.

• Do not restrict the air flow of this unit by placing it somewhere with poor air flow, by covering it with a cloth, or by placing it on bedding or carpeting.

SAFETY INFORMATION

• When connecting or disconnecting the AC cord, grip the plug and not the cord itself. Pulling the cord may damage it and create a hazard.

• When you are not going to use the unit for a long period of time, disconnect the AC cord.

CONDENSATION INFORMATION

• When left in a heated room where it is warm and damp, water droplets or condensation may form inside the unit. When there is condensation inside the unit, the unit may not function normally. Let the unit stand for 1-2 hours before turning the power on, or gradually heat the room and let the unit dry before use.

FCC INFORMATION

WARNING: Changes or modifications to this unit not expressly approved by the party responsible

for compliance could avoid the user authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Shielded cables must be used with this unit to ensure compliance with the Class FCC limits.

WARNING: Should any problems occur, disconnect the AC cord and refer servicing to a qualified technician.

PLV36190CS1_IB_ENG_JEN_R1.pmd 11/2/2007, 5:09 PM2

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation

openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources

such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of

the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being

walked on or pinched particularly at plug, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories

specified by the manufacture.

12. Use only with the cart,

stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

PLV36190CS1_IB_ENG_JEN_R1.pmd 11/2/2007, 5:09 PM3

TABLE OF CONTENTS

SAFETY PRECAUTIONS ...................................................................................... 2

IMPORTANT SAFETY INSTRUCTIONS ............................................................... 3

REMOTE CONTROL ........................................................................................... 5

ACCESSORIES ..................................................................................................... 5

REMOTE CONTROL REFERENCE GUIDE .......................................................... 6

UNIT REFERENCE GUIDE ................................................................................. 7

CONNECTIONS ......................................................................................... 8 – 13

Connecting a TV Antenna/Cable/Satellite ......................................................... 8

Connecting an Audio Amplifier ......................................................................... 8

Connecting an A/V Device (VCR, PVR Camcorder, Game System, etc.) ... 9 – 11

Connecting a High-Definition (HD) Source .................................................... 12

Connecting a PC ............................................................................................. 12

POWER SUPPLY ................................................................................................ 13

Using the Car Power Adapter .......................................................................... 13

Using the AC Power Adapter .......................................................................... 13

INSTALLATION .................................................................................................... 14

Removing the Base Stand ................................................................................ 14

Mounting on the Wall ..................................................................................... 14

USING HEADPHONES .................................................................................... 15

UNIT OPERATION ............................................................................................ 15

Turning the Unit on for the First Time .............................................................. 15

TV SETUP .................................................................................................. 16 – 21

Video Menu .................................................................................................... 16

VGA Settings in PC Mode .............................................................................. 17

Audio Menu .................................................................................................... 17

TV Menu ......................................................................................................... 18

Channel Skip Setting ....................................................................................... 18

Setup Menu ............................................................................................. 18 – 20

Time Setup Setting ......................................................................................... 19

Caption Setting .............................................................................................. 20

Restore Setting ............................................................................................... 20

Parental Menu .......................................................................................... 20 – 21

Password ....................................................................................................... 20

Parental Control Setting .................................................................................. 21

TROUBLE SHOOTING GUIDE ........................................................................ 22

PLV36190CS1_IB_ENG_JEN_R1.pmd 11/2/2007, 5:09 PM4

REMOTE CONTROL

USING THE REMOTE CONTROL

• Point the remote control at the REMOTE SENSOR located on the unit.

• When using this unit in very bright light, the infrared REMOTE CONTROL SENSOR may not work properly.

• The recommended effective distance for using the remote control is about 16 feet (5 meters).

TO CHANGE THE REMOTE CONTROL BATTERY

1. Open the battery door. 2. Insert two “AAA” batteries.

BATTERY REPLACEMENT

When the batteries become weak, the operating distance of the remote control will be greatly reduced and you will need to replace the batteries.

Note: • If the Remote Control is not going to be used for a long time, remove the batteries to

avoid damage caused by battery leakage corrosion.

• Do not mix old and new batteries. Do not mix ALKALINE, standard (CARBON-ZINC) or rechargeable (NICKEL-CADMIUM) batteries.

WARNING: Do not dispose of batteries in a fire or they may leak and/or explode.

Many universal remote controls have a “learning” feature, we recommend you use that feature to program the remote control.

For any questions or problems related to programming a universal remote control, you must contact the customer service department of the universal remote control manufacturer for assistance, or refer to the instructions included with the universal remote control. We cannot offer assistance in programming universal remote controls.

ACCESSORIES

PLEASE LOCATE THE INCLUDED ACCESSORIES.

Remote control (with battery) .............................................................................. x 1

AC adapter ...................................................................................................... x 1

Car power adapter ............................................................................................ x 1

Audio/Video Cable ............................................................................................ x 1

Mount screw ................................................................................................... x 4

Specifications and appearance are subject to change without notice.

JE1908_IB_ENG_JEN_R1.pmd 11/6/2007, 2:47 PM5

REMOTE CONTROL REFERENCE GUIDE

5) DISPLAY Button

Press to show which input you are

1) SLEEP Button

Press to set the SLEEP timer. The unit will remain on for the time that is set, and will automatically shut off afterwards.

2) Number (0 - 9 and dot) Buttons

Use to change the TV channels.

3) LAST CH Button

Press to switch repeatedly between the last two channels displayed.

4) PICTURE Button

Press to select from preset screen display settings to match the type of show you are watching (Standard, Dynamic, Personal, Soft & Movie)

watching (TV channel / AV / YUV / PC).

6) CURSOR (

Press to highlight selections on a menu screen and adjust certain settings.

CH+/CH– Button

Press CH+/CH– to change the TV channels.

VOLUME (–/+) Buttons

Press to adjust the volume level.

7) TV Button

Press to select TV mode.

8) CC Button

Press to activate the Closed Captioning feature. This function only works on programs broadcast with captions.

9) EXIT Button

Press to return to previous menu or exit the menu and return directly to normal viewing.

10) STANDBY Button

Press to turn ON the unit or put it in STANDBY (OFF) mode.

11) MUTE Button

Press to mute the sound. Press again to cancel mute.

12) FUNCTION Button

Press to switch between TV / AV IN / YUV IN / PC IN.

13) SOUND Button

Press to select from preset sound settings (Personal, Standard, Voice, Music, Theater) to match the type of show you are watching.

14) ENTER Button

Press to confirm selections on a menu screen.

15) MENU Button

Press to display the on-screen menu.

16) AV Button

Press to select AV IN mode.

17) MTS Button

Press to select MONO sound, STEREO sound and Secondary Audio Program (SAP).

18) FORMAT Button

Press to select the picture format.

, , , ) Buttons

PLV36190CS1_IB_ENG_JEN_R1.pmd 11/2/2007, 5:09 PM6

UNIT REFERENCE GUIDE

1) Color LCD Screen

2) STANDBY Indicator

Indicates whether the unit is ON or in STANDBY (OFF) mode. Light On: The unit is in STANDBY. Light Off: The unit is turned ON.

REMOTE CONTROL SENSOR

Do not block this sensor or remote control will not work.

3) Removable Base Stand

4) STANDBY/ON Button

Turns the unit on and off.

5) MENU Button

Enters and exits the TV menu.

6) FUNCTION Button

Selects TV, AV IN, YUV IN or PC IN.

7) – VOL + Controls

Adjusts the volume level and highlight selections (Left & Right) on the menu screen.

/ Buttons

Selects a TV channel and highlight selections (Up & Down) on the menu screen.

9) DC IN 12V

10) AV OUT Video Output Jack

11) AV OUT Audio Output Jacks (Left/ Right)

12) AV IN Video Input Jack

13) AV IN Audio Input Jacks (Left/Right)

14) PC IN MONITOR/VGA Jack

15) PC IN Audio Jack

16) YUV IN Component Video Input Jacks (Y/P

17) YUV IN Audio Input Jacks (Left/Right)

18) AV IN S-Video Input Jack

19) Headphone Jack

20) TV Antenna Cable Terminal - Coaxial TV Antenna Input

4 5

9 10 11 12

7 8

B/PR)

14 15 16 17 18 20

PLV36190CS1_IB_ENG_JEN_R1.pmd 11/2/2007, 5:09 PM7

CONNECTIONS

CONNECTING A TV ANTENNA/CABLE/SATELLITE

To view television channels correctly, a signal must be received from one of the following sources:

- An indoor or outdoor aerial antenna

- A cable system

- A satellite system

Connecting a Digital Antenna

The tuner in this TV receives ATSC TV signals from an antenna. This digital TV can receive standard (SDTV) and high definition (HDTV) over the air broadcasts.

Connecting an Analog Antenna or Device

The tuner in this TV can receive NTSC TV signals, analog cable signals or the RF output from a satellite receiver, VCR or cable box.

Satellite, Cable, or

TV antenna cable to

TV ANTENNA

CABLE Terminal

(cable not included)

CONNECTING AN AUDIO AMPLIFIER

This connection allows you to use an audio amplifier and external speakers.

Connect the right (red) and left (white) audio OUTPUT from this unit to the right (red) and left (white) audio INPUT on your amplifier. Refer to your amplifier’s user manual for more information.

Note:

To control the audio, both the TV and the amplifier must be turned on, and the volume of the amplifier must be set above 0, or you will not hear any sound. If you want to hear the sound from the amplifier only, press the VOL – button on the TV to decrease the volume or press the MUTE button on the remote control to turn off the sound.

PLV36190CS1_IB_ENG_JEN_R1.pmd 11/2/2007, 5:09 PM8

+ 16 hidden pages