Janome Horizon Memory Craft 8200QCP Instruction Manual

Instruction Book

IMPORTANT SAFETY INSTRUCTIONS

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

When using an electrical appliance, basic safety precautions should always be followed, including the following:

This sewing machine is designed and manufactured for household use only.

Read all instructions before using this sewing machine.

To reduce the risk of electric shock:

DANGER

An appliance should never be left unattended when plugged in. Always unplug this sewing machine from the electric outlet immediately after using and before cleaning.

WARNING

1. Do not allow to be used as a toy. Close attention is necessary when this sewing machine is used by or near

children.

2. Use this appliance only for its intended use as described in this owner’s manual.

Use only attachments recommended by the manufacturer as contained in this owner’s manual.

3. Never operate this sewing machine if it has a damaged cord or plug, if it is not working properly, if it has been

dropped or damaged, or dropped into water.

Return this sewing machine to the nearest authorized dealer or service center for examination, repair, electrical or

mechanical adjustment.

4. Never operate the appliance with any air opening blocked. Keep ventilation openings of this sewing machine and

foot controller free from accumulation of lint, dust and loose cloth.

5. Never drop or insert any object into any opening.

6. Do not use outdoors.

7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

8. To disconnect, turn all controls to the off (“O”) position, then remove plug from outlet.

9. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

10. Keep ﬁngers away from all moving parts. Special care is required around the sewing machine needle.

11. Always use the proper needle plate. The wrong plate can cause the needle to break.

12. Do not use bent needles.

13. Do not pull or push fabric while stitching. It may deﬂect the needle causing it to break.

14. Switch this sewing machine off (“O”) when making any adjustment in the needle area, such as threading the

needle, changing the needle, threading the bobbin or changing the presser foot, and the like.

15. Always unplug this sewing machine from the electrical outlet when removing covers, lubricating, or

when making any other adjustments mentioned in this owner’s manual.

—

To reduce the risk of burns, ﬁre, electric shock, or injury to persons:

SAVE THESE INSTRUCTIONS

Please note that on disposal, this product must be safely recycled in accordance with relevant National legislation relating to electrical/electronic products. If in doubt please contact your retailer for guidance. (European Union only)

TABLE OF CONTENTS

NAMES OF PARTS

Names of Parts ............................................................... 3

Standard Accessories .................................................... 4

Accessories Storage ...................................................... 5

Extension Table .............................................................. 5

GETTING READY TO SEW

Connecting the Power Supply ........................................ 6

Operating Instructions .................................................... 6

Machine Operating Buttons ............................................ 7

Controlling Sewing Speed .............................................. 8

Foot control .................................................................... 8

Function Keys ................................................................. 9

Raising and Lowering the Presser Foot ....................... 10

Knee Lifter .................................................................... 10

Adjusting the Foot Pressure ..........................................11

Dropping the Feed Dog ................................................. 11

Balancing Thread Tension ............................................ 12

Lockout Key .................................................................. 13

Changing the Presser Foot .......................................... 13

Removing and Attaching the Foot Holder .................... 14

Dual Feed Foot .........................................................14 -15

Replacing the Needle Plate .......................................... 16

Changing Needles ........................................................ 17

Fabric and Needle Chart .............................................. 17

Winding the Bobbin ...................................................... 18

Winding the Bobbin ...................................................... 19

Inserting the Bobbin ..................................................... 20

Threading the Machine ................................................. 21

Built-in Needle Threader .............................................. 22

Drawing up the Bobbin Thread..................................... 23

Selecting the Patterns .................................................. 24

Customizing Machine Settings ................................ 25-27

TRADITIONAL SEWING

Straight Stitch .......................................................... 28-30

Sewing with the Dual Feed Device............................... 31

Dual Feed Balancing Dial ............................................. 31

Needle Plate for Straight Stitch .................................... 32

Lock-a-Matic Stitch ....................................................... 32

Locking Stitch ............................................................... 32

Straight Stitch with Left Needle Position ...................... 33

Triple Stretch Stitch ...................................................... 33

Knit Stitch ..................................................................... 33

Zipper Sewing ......................................................... 34-36

Rolled Hem ................................................................... 37

Gathering ...................................................................... 38

Pintucking ..................................................................... 38

Zigzag Stitch ................................................................. 39

Multiple Zigzag Stitch (Tricot stitch) ............................. 40

Overcasting Stitch ........................................................ 40

Knit Stitch ..................................................................... 41

Double Overcasting Stitch ............................................ 41

Blind Hemming ........................................................ 42-43

Shell Tuck ..................................................................... 44

Buttonholes .................................................................. 44

Square Buttonhole................................................... 45-48

Using the Stabilizer Plate ............................................. 49

Round End and Fine Fabric Buttonholes ..................... 50

Keyhole Buttonhole ...................................................... 50

Stretch Buttonholes ...................................................... 50

Corded Buttonhole ....................................................... 51

Welted Buttonhole ................................................... 52-53

Button Sewing .............................................................. 54

Darning ....................................................................55-56

Tacking ......................................................................... 57

Eyelet ............................................................................ 58

Applique ....................................................................... 59

Fringing ......................................................................... 60

Drawn Work ............................................................. 60-61

Smocking ...................................................................... 61

Fagoting ........................................................................ 62

Scallop .......................................................................... 62

Patchwork Piecing ........................................................ 63

Patchwork ..................................................................... 63

Quilting ......................................................................... 64

Stippling ........................................................................ 65

Clasp Stitches .............................................................. 65

Free Motion Quilting (1) ...........................................65-66

Free Motion Quilting (2) ................................................ 66

Satin Stitches ............................................................... 67

Twin Needle Sewing ................................................ 68-69

PROGRAMMING A PATTERN COMBINATION

Pattern Combination ..................................................... 70

Programming Auto-lock Stitch ...................................... 71

Programming Automatic Thread Cutting ...................... 72

Pattern Combination with a Mirror Image ..................... 73

Resuming a Pattern from the Beginning ...................... 74

Resuming a Pattern Combination from the Beginning . 74

Bridge Stitches ........................................................ 75-76

Monogramming ........................................................77-78

Editing a Pattern Combination ...................................... 79

Deleting and Inserting a Pattern ................................... 80

Duplicating a Pattern .................................................... 80

Uniform Stitch Adjustment ............................................ 81

Uniﬁed Needle Drop Position ....................................... 81

Individual Stitch Adjustment ......................................... 82

Correcting Distorted Stitch Patterns ............................. 83

CARE AND MAINTENANCE

Cleaning the Hook Area ............................................... 84

Cleaning the Inside of the Thread Guide ...................... 85

Problems and Warning Signals ............................... 86-87

Troubleshooting ............................................................ 88

!0!1

!5 !6

NAMES OF PARTS

Names of Parts

Thread take-up lever

Foot pressure dial

Reference chart

Top c over

Foot storage compartment

Bobbin thread cutter

Bobbin winder spindle

Hole for extra spool pin

Spool holder (large)

Spool pin

Thread tension dial

Face cover

Thread cutter

Extension table (accessory storage)

Needle plate release lever

Start/stop button

Reverse button

Auto-lock button

Needle up/down button

Thread cutter button

Speed control slider

Feed balancing dial

Knee lifter socket

Function keys

LCD screen

Needle clamp screw

Needle

Zigzag foot A

Needle plate

Hook cover release button

Hook cover plate

Buttonhole lever

Needle threader

Foot holder

Carrying handle

Presser foot lifter

Handwheel

Dual feed balancing dial

Drop feed lever

Power switch

Foot control jack

Machine socket

NOTE:

To carry the sewing machine, hold the carrying handle with your hand, and support the sewing machine with the other hand.

NOTE:

Sewing machine design and speciﬁcations are subject to change without prior notice.

q w e r

y u i o

!4 !5

@1 @2 @3

#1 #2

Standard Accessories

Zigzag foot A (set on the machine)

Rolled hem foot D

Zipper foot E

Satin stitch foot F

Open-toe satin stitch foot F2

Blind hemming foot G

Overcast foot M

1/4˝ seam foot O

Darning foot PD-H

Convertible free motion quilting foot QB-S

Close-toe foot

Open-toe foot

Clear view foot

Automatic buttonhole foot R

Buttonhole stabilizer plate

Dual feed foot holder

Dual feed foot AD

Button sewing foot T

Quilting guide bar

Bobbin (5 pcs.) (1 set on the machine)

Spool holder (large, set on the machine)

Spool holder (small)

Spool supporter

Felt cusion

Extra spool pin

Needle set

Screwdriver

Lint brush

Seam ripper (Buttonhole opener)

Knee lifter

Needle plate for straight stitch

Touch panel stylus

Power cable

Foot control

Instructional video DVD

Instruction book

#4 #5

Accessories Storage

The accessories can be conveniently stored in the foot storage compartment under the top cover and in the extension table.

Under top cover:

q Zigzag foot A w Overcast foot M e Zipper foot E r Satin stitch foot F t Blind hemming foot G y Foot holder u Touch panel stylus i Clear view foot o Open-toe foot !0 Close-toe foot !1 Convertible free motion quilting foot QB-S

In extension table:

q Buttonhole stabilizer plate w Automatic buttonhole foot R e Needle plate r Bobbin t Presser foot

Other accessories can be also stored in the compartment.

Extension Table

The extension table provides an extended sewing area and can be removed for free-arm sewing. q Extension table w Free-arm

To detach:

Draw the table out to the left.

To attach:

Slide the table on the base and push the table to the right.

Free-arm sewing

Free-arm sewing is used for stitching sleeves, waistbands, pant legs or any other tubular garments. It is also useful for darning socks or mending knees or elbows. w Free-arm

GETTING READY TO SEW

Connecting the Power Supply

z First make sure the power switch q is off. x Insert the machine plug w of the power supply cord

into the machine socket e.

c Insert the power supply plug r into the wall outlet t,

and turn the power switch q on.

q Power switch w Machine plug e Machine socket r Power supply plug t Wall outlet

NOTES:

Make sure to use the power supply cable that came with the machine. If you turn off the power switch, wait for 5 seconds before turning it on again.

If you wish to use the foot control, insert the pin connector into the jack on the machine.

z First make sure the power switch q is off. x Insert the pin connector w into the jack e on the

c Insert the machine plug r of the power supply cord

v Insert the power supply plug y into the wall outlet u,

The foot control sign i will be displayed when the foot

q Power switch w Pin connector e Jack r Machine plug t Machine socket y Power supply plug u Wall outlet i Foot control sign

WARNING :

While in operation, always keep your eyes on the sewing area, and do not touch any moving parts such as the thread take-up lever, handwheel or needle. Always turn off the power switch and unplug the machine from the power supply:

- when leaving the machine unattended.

- when attaching or removing parts.

- when cleaning the machine. Do not place anything on the foot control.

machine.

into the machine socket t.

and turn the power switch on.

control is connected to the machine.

NOTE:

The start/stop button does not work when the foot control is connected.

Operating Instructions:

The symbol “O” on a switch indicates the “off” position of the switch.

For the U.S.A. and Canada only

Polarized plug (one blade wider than the other): To reduce the risk of electric shock, this plug is intended to ﬁt in a polarized outlet only one way. If it does not ﬁt fully in the outlet, reverse the plug. If it still does not ﬁt, contact a qualiﬁed electrician to install the proper outlet. Do not modify the plug in any way.

Machine Operating Buttons

q Start/stop button

Press this button to start or stop the machine. The machine starts running slowly for the ﬁrst few stitches, it then runs at the speed set by the speed control slider. The machine runs slowly as long as this button is pressed.

The button will turn red when the machine is running, and green when it has been stopped.

Pressing and holding this button while sewing will slow down the sewing speed and the machine will stop when the button is released.

NOTES:

•Thestart/stopbuttoncannotbeusedwhenthefoot

control is connected to the machine.

•Themachinewillnotrunandthepresserfootmark

y will blink if you start the presser foot in the up position. Lower the presser foot and press the start/ stop button.

•Youcanselectthedesiredstart-upspeedfrom

slow, medium or high (refer to page 26).

w Reverse button

When sewing stitch pattern 1, 4, 6, 7, 8, 1S, 4S (mode 1), 01, 04, 08, 09, 10 (mode 2) or 01, 02, 03, 46, 47 (mode

3), the machine will sew in reverse as long as the reverse button is pressed.

If stitch pattern 1, 4, 6, 7, 8, 1S, 4S (mode 1), 01, 04, 08, 09, 10 (mode 2) or 01, 02, 03, 46, 47 (mode 3), has been selected and the foot control is not connected, the machine will start sewing in reverse as long as the reverse button is pressed.

If you press the reverse button when sewing any other patterns, the machine will immediately sew locking stitches and automatically stop.

e Auto-lock button

When sewing stitch pattern 1, 4, 6, 7, 8, 1S, 4S (mode 1), 01, 04, 08, 09, 10 (mode 2) or 01, 02, 03, 46, 47 (mode

3), the machine will immediately sew locking stitches and automatically stop when the auto-lock button is pressed.

When sewing all other patterns, the machine will sew to the end of the current pattern, sew locking stitches and stop automatically. The machine will trim the threads automatically after locking the stitch when the auto thread cutting option is turned on.

r Needle up/down button

Press this button to bring the needle bar up or down. The machine will stop with the needle in down position. However, you can change the needle stop position in the setting mode (refer to page 26).

t Thread cutter button Press this button when you ﬁnish sewing to trim the threads. The needle bar automatically rises after trimming the threads (refer to page 29).

NOTE:

Use the thread cutter on the face cover if the thread is #30 or thicker (refer to page 29).

Controlling Sewing Speed

Speed control slider

Youcanlimitthemaximumsewingspeedwiththespeed

control slider according to your sewing needs. To increase the sewing speed, move the slider to the right. To decrease the sewing speed, move the slider to the left.

Foot control

Pressing on the foot control can vary sewing speed. The harder you press the foot control, the faster the machine runs.

NOTE:

The machine runs at the maximum speed set by the speed control slider when the foot control is fully depressed.

Operating Instructions:

FootcontrolmodelYC-485EC-1isforusewiththis

sewing machine.

r t

Function Keys

q LCD screen

The LCD screen shows the following information when the machine is turned on:

w Stitch pattern e Mode r Stitch pattern number t Recommended type of presser foot y Stitch width u Stitch length

i Cursor key (refer to pages 79, 80) Press “ ” or “ ” to move the cursor to check or edit the pattern combination.

o Stitch width adjusting key (refer to pages 30, 39, 49) Press this key to alter the stitch width.

!0 Stitch length adjusting key (refer to pages 30, 39, 49) Press this key to alter the stitch length.

!1 Mode key (refer to page 25) Press the mode key to select the mode. When the power is turned on, the direct pattern selection (mode 1) is set automatically.

!2 Number keys (refer to page 24)

•Directpatternselection

Youcanselectthestitchpatternsfrom0to9directlyin

mode 1 (direct pattern selection mode).

•Numericpatternselection

Enter a 2-digit pattern number to select the desired stitch pattern in modes 2 to 6.

!7 !8

!5 Memory key (refer to pages 70)

Press this key to register programmed pattern combinations. Stitch patterns in mode 2 to 6 can be Up to 50 stitch patterns combination can be memorized.

!6 Clear key (refer to pages 26, 80) Press the clear key to clear the memorized stitch pattern. Press and hold this key until the buzzer sounds to delete the whole pattern combination.

!7 Set key (refer to page 25) Press this key to enter the setting mode for customizing the machine settings.

!8 Elongation key (refer to page 67) Press this key to elongate satin stitch patterns.

!9 Startover key (refer to page 74) Press this key to sew a pattern combination from the beginning.

@0 Lockout key (refer to page 13) Press this key to lockout the machine when threading the machine, replacing the accessories etc. To reduce the risk of injury, all the buttons and keys are deactivated. To unlock the machine, press this key again.

!3 Twin needle key (refer to page 69)

Press this key when sewing with a twin needle.

!4 Mirror image key (refer to pages 73) Press this key to sew a mirror image of the selected pattern.

Raising and Lowering the Presser Foot

The presser foot lifter raises and lowers the presser foot. q Presser foot lifter

You can raise the presser foot higher than the normal up position. This allows for changing the needle plate, and also helps you to place thick layers of fabrics under the foot. w Extra lifted position

NOTE:

Do not turn the hand wheel of press the up/down needle button when the presser foot is in the extra lifted position.

Knee Lifter

The knee lifter is extremely helpful when sewing patchwork, quilting etc, since it allows you to handle the fabric while your knee controls the presser foot.

Attaching the knee lifter

Match the ribs on the knee lifter with the notches in the knee lifter socket and insert the knee lifter.

q Knee lifter w Rib e Knee lifter socket

Adjusting the knee lifter

The angle of the knee lifter can be adjusted to ﬁt you. Loosen the setscrew and slide the angle bar in or out to adjust the angle of the knee lifter. Tighten the setscrew to secure the angle bar.

r Setscrew t Angle bar

Using the knee lifter

Push the knee lifter with your knee to easily move the presser foot up and down. You can control how high the foot rises by the amount of knee pressure you exert.

NOTE:

Do not touch the knee lifter while stitching, otherwise the fabric will not be fed smoothly.

Adjusting the Foot Pressure

The foot pressure can be adjusted with the foot pressure dial located under the top cover.

The dial has 7 setting positions from 1 to 7. For ordinary sewing, set 5 at the setting mark.

q Foot pressure dial w Setting mark

Reduce the pressure when sewing ﬁne synthetics and stretch fabrics. To reduce the pressure, set the dial at a lower number.

Increase the pressure when sewing heavy weight fabrics. To increase the pressure, set the dial at a higher number.

Dropping the Feed Dog

The feed dog can be lowered for basting, sewing on buttons, free motion quilting etc.

Shift the drop feed lever toward you to lower the feed dog.

q Drop feed lever w Feed dog

Shift the drop feed lever away from you to raise the feed dog, it will return to the up position when you start the machine.

NOTE:

If you start the machine with the feed dog lowered, a message will appear on the LCD screen. The machine will not run with the feed dog lowered when pattern number 19 to 25, and 27 to 29 in mode 2 or stitch patterns in modes 4, 5 and 6 is selected.

Balancing Thread Tension

Auto-thread tension

For general sewing, set the thread tension dial at AUTO, which covers a wide range of sewing conditions. q Thread tension dial

NOTE:

Manual thread tension adjustment may be required when the stitch width is set more than “7.0” (see below).

Balanced thread tension

For straight stitch sewing, both needle and bobbin threads will join at the middle of the fabrics.

For zigzag stitch sewing, the needle thread will appear slightly on the wrong side of the fabric.

q Wrong side of fabric w Right side of fabric e Needle thread r Bobbin thread

Manual thread tension adjustment

YoushouldadjustthetensionmanuallyiftheLCDscreen

shows a tension setting other than AUTO.

Youmayalsoneedtoadjusttensionmanuallydepending

on the sewing conditions such as the type of fabric and number of layers.

If the needle thread is too tight, the bobbin thread appears on the right side of the fabric.

q Wrong side of fabric w Right side of fabric e Needle thread r Bobbin thread

Turn the thread tension dial to a lower number to decrease the thread tension.

If the needle thread is too loose, the needle thread loops on the underside of the fabric.

q Wrong side of fabric w Right side of fabric e Needle thread r Bobbin thread

Turn the thread tension dial to a higher number to increase the thread tension.

Lockout Key

Press this key to lockout the machine when threading the machine, replacing the accessories etc. To reduce the risk of injury, all the buttons and keys are deactivated.

To unlock the machine, press this key again.

Changing the Presser Foot

CAUTION:

Always make sure to press the lockout key to lockout the machine or turn the power switch off before replacing the presser foot.

Raise the needle to its highest position and raise the presser foot lifter. Press the black lever on the back of the foot holder. The presser foot will drop off.

q Lever w Presser foot

Attaching the presser foot

Place the presser foot so that the pin on the foot lies just under the groove of the foot holder. Lower the presser bar to lock the foot in place. Each foot is marked with an identiﬁcation letter.

e Groove r Pin t Identiﬁcation letter

Removing and Attaching the Foot Holder

CAUTION:

Always make sure to press the lockout key to lockout the machine or turn the power switch off before replacing the presser foot.

Removing the foot holder

Raise the presser foot and loosen the setscrew. Remove the foot holder.

Attaching the foot holder

Attach the foot holder to the presser bar from the rear. Tighten the thumbscrew securely with the screwdriver.

q Presser bar w Foot holder e Setscrew

Dual Feed Foot

CAUTION:

Always make sure to press the lockout key to lockout the machine or turn the power switch off before replacing the presser foot.

z Raise the needle to its highest position. Raise the presser foot lifter.

q Presser foot lifter

w Needle

x Loosen the setscrew.

Remove the foot holder.

e Foot holder r Setscrew

c Attach the dual feed foot holder to the presser bar.

Tighten the setscrew lightly with your ﬁnger.

t Dual feed link y Dual feed foot holder u Upper feed drive i Dual feed foot

v Push the dual feed link to engage it with upper feed

drive.

b Lower the presser foot lifter. Lower the needle to the

lowest position by turning the handwheel.

n Tighten the setscrew securely with the screwdriver.

Replacing the dual feed foot

Pull the foot toward you to remove it.

Insert the pins of the foot into the slits of the foot holder and gently push the foot until it snaps into place.

q Pin

w Slit

Replacing the Needle Plate

Use the straight stitch needle plate when sewing ﬁne fabrics or sewing with the dual feed foot.

CAUTION:

Always make sure to press the lockout key to lockout the machine or turn the power switch off before replacing the needle plate.

z Turn the handwheel and raise the needle to the

highest position.

Raise the presser foot lifter to the extra lifted position.

q Presser foot lifter w Needle

x Slide the extension table to the left to remove it.

Push down the needle plate release lever and the

needle plate will snap off.

e Needle plate release lever r Needle plate

c Place the straight stitch needle plate on the machine.

Set the left edge of the needle plate into the opening.

v Push down on the needle plate mark until the needle

plate locks in place.

Turn the power switch on or press the lockout key to

unlock.

Turn the hand wheel slowly and make sure that the

needle does not hit the needle plate.

t Needle plate mark

CAUTION:

Never press the needle plate release lever while running the machine.

Changing Needles

CAUTION:

Always make sure to press the lockout key to lockout the machine or turn the power switch off before changing the needle.

Raise the needle by pressing the needle up/down button and lower the presser foot. Turn the power switch off.

Loosen the needle clamp screw and remove the needle from the clamp. q Needle clamp screw

Fabric

Fine

Medium

Heavy weight

Lawn

Georgette

Tricot

Sheeting

Jersey

Wool

Knit

Denim

Tweed

Coating

Quilting

Thread Needle

Silk #80-100

Cotton #80-100

Synthetic #80-100

Silk #50

Cotton #50-80

Synthetic #50-80

Silk #30-50

Cotton #40-50

Synthetic #40-50

Purple tip needle

Insert a new needle into the needle clamp with the ﬂat side of the needle to the rear. When inserting the needle into the needle clamp, push it up against the stopper pin and tighten the needle clamp screw ﬁrmly with a screwdriver. w Flat side e Stopper pin

To check needle straightness, place the ﬂat side of the needle onto something ﬂat (a needle plate, glass etc.) The gap between the needle and the ﬂat surface should be consistent. Never use a blunt needle. r Gap

Fabric and Needle Chart

•Forgeneralsewing,useneedlesize

#11/75 or #14/90.

•Finethreadsandneedlesshouldbeused

for sewing ﬁne fabrics.

#9/65-11/75

Blue tip needle

#11/75-14/90

Red tip needle

#14/90-16/100

•Ingeneral,usethesamethreadforboth

needle and bobbin.

•Useabluetipneedleforsewingnefabrics,

stretch fabrics and buttonholes to prevent skipped stitches.

•Useapurpletipneedleforsewingthick

fabrics,

denims, quilt layers and across the hem to

prevent skipped stitches.

•Useastabilizerorinterfacetostretchorne

fabrics to prevent seam puckering.

•Alwaystestthethreadandneedlesizeona small piece of the same fabric you will use for actual sewing.

NOTE:

1 x twin needle, 2 x blue tip needle (#11/75), 1 x red tip needle (#14/90) and 1 x purple tip needle (#14/90) are included in the needle case.

Winding the Bobbin

Removing the Bobbin

Slide the hook cover release button to the right, and remove the hook cover plate. q Hook cover release button w Hook cover plate

Lift out the bobbin from the bobbin holder. e Bobbin

NOTE:

Use the Janome plastic bobbins for horizontal hook (marked with “J” r). Using other bobbins, such as pre-wound paper bobbins, may cause stitching problems and/ or damage to the bobbin holder.

Setting the spool of thread

Lift up the spool pin. Place the spool of thread on the spool pin. Attach the large spool holder, and press it ﬁrmly against the spool of thread. q Large spool holder

NOTE:

Use the small spool holder to hold narrow or small spools of thread. w Small spool holder

Extra spool pin

Use the extra spool pin when you need to wind a bobbin without unthreading the machine while working on a sewing project. Insert the extra spool pin into the spool supporter and then into the hole beside the horizontal spool pin. Place the felt cushion on the spool pin and place a spool of thread on it as shown. e Extra spool pin r Spool supporter t Hole for extra spool pin y Felt cushion

NOTE:

The extra spool pin is also used for twin needle sewing.

Winding the Bobbin

c v

z Pull the thread from the spool.

Hold the thread with both hands and pass the thread

into the guide slot.

q Guide slot x Draw the thread to the left and forward around the

thread guide.

Draw the thread to the rear and to the right around

under the guide plate.

Firmly pull the thread to the right while holding it with

both hands.

w Thread guide e Guide plate

c Pass the thread through the hole in the bobbin from

the inside to the outside. Put the bobbin on the bobbin winder spindle. Push the bobbin to the right. The bobbin mark appears

on the LCD screen. r Hole t Bobbin mark v Hold the free end of the thread in your hand and start

the machine. Stop the machine when the bobbin has wound several

layers, and cut the thread close to the hole in the

bobbin.

NOTE:

Set the speed control slider at the fastest position.

b Start the machine again.

Stop the machine when the bobbin is fully wound and

stops spinning. Return the bobbin winder spindle to its original

position. Remove the bobbin and cut the thread with the thread

cutter. y Thread cutter

NOTE:

For safety purposes, the machine will automatically stop approximately 90 seconds after starting bobbin winding.

Inserting the Bobbin

z Place the bobbin in the bobbin holder with the thread

running off counterclockwise.

CAUTION:

Always make sure to press the lockout key to lockout the machine or turn the power switch off before threading the machine.

x Guide the thread into the front notch on the bobbin

holder.

q Front notch

c Draw the thread to the left, sliding it between the

tension spring blades.

w Tension spring blades

v Continue to draw the thread lightly until the thread

slips into the side notch.

e Side notch

b b Pull out about 10 cm (4˝) of thread to the rear.

Reattach the hook cover plate. r Hook cover plate

NOTE:

The threading chart is shown on the hook cover plate for your reference.

Threading the Machine

Raise the presser foot lifter to raise the presser foot. Turn the power switch on. Press the needle up/down button to raise the take-up lever to the highest position. Press the lockout key or turn the power switch off. Pass the thread in the order from z to m.

CAUTION:

Always make sure to press the lockout key to lockout the machine or turn the power switch off before threading the machine.

z Hold the thread with both hands and pass the thread

into the guide slot.

q Guide slot

x Hold the thread with both hands and draw the thread

around the corner of the guide.

Firmly pull the thread toward you along the right

channel until the thread snaps.

w Corner of the guide e Right channel

c Draw the thread down along the right channel and

around the bottom of the thread guide plate. Pull the thread up along the left channel.

e Right channel r Thread guide plate t Left channel

v While holding the thread at the spool, ﬁrmly draw the

thread up and to the back of the take-up lever. Draw the thread forward to slip it into the eye of the take-up lever.

y Eye of the take-up lever

b n m

b Then pull the thread down along the left channel and

through the lower thread guide.

u Lower thread guide

n Slide the thread behind the needle bar thread guide

on the left.

i Needle bar thread guide

m Thread the needle with the needle threader (refer to

the next page).

Built-in Needle Threader

NOTES:

•Theneedlethreadercanbeusedwitha#11to#16

needle.

Thread size 50 to 90 is recommended.

•Theneedlethreadercannotbeusedwiththetwin

needle.

CAUTION:

Always make sure to press the lockout key to lockout the machine or turn the power switch off before using the built-in needle threader.

z Turn the power switch ON. Press the needle up/down button to raise the needle. Press the lockout key to lock the machine. Pull down the needle threader knob as far as it will go. The threader hook comes out through the needle eye

from behind.

q Needle up/down button w Threader knob e Threader hook

x Draw the thread from left to right, under the left guide,

threader hook and right guide.

Draw the thread around the right guide toward you. r Left guide t Right guide

c Raise the threader slowly so a loop of the thread is

pulled up through the needle eye.

y Threader loop

v Remove the thread end through the needle eye to the

re a r.

NOTE:

The needle threader cannot be used with the twin needle.

Drawing up the Bobbin Thread

z Raise the presser foot lifter.

Hold the needle thread with your ﬁnger. q Needle thread

x Press the needle up/down button twice to draw up the

bobbin thread. w Needle up/down button

c Pull the needle thread to bring up the loop of bobbin

thread. e Loop of bobbin thread

v Pull both threads 10 cm (4˝) and draw them to the rear

under the presser foot.

Selecting the Patterns

Mode 1

Youcanselectthefollowingstitchpatternsdirectlyby

pressing the pattern keys.

q Pattern keys (Number keys)

Example: To select stitch pattern 4 in mode 1

When the power switch is turned on, the direct stitch pattern selection (mode 1) is set automatically.

Press the pattern key 4 to select the stitch pattern 4. Now pattern 4 (mode 1) is selected.

Mode 2 – 6

To select stitch patterns in modes 2–6, ﬁrst press the mode key w to select your desired mode. Each time you press the mode key, the mode number e indicated on the left side of the screen will change, and the mode changes as follows,

Mode 1: Direct pattern selection Mode 2: Utility stitch pattern selection Mode 3: Decorative stitch pattern selection Mode 4: Number and letter selection Mode 5: European accented letter selection Mode 6: 9 mm monogram selection

Example: To select stitch pattern 53 in mode 3

z Turn the power switch on. Press the mode key twice

to select mode 3.

x Press the number keys on the touch panel. First press

key 5 and then press key 3.

c Now pattern 53 in mode 3 is selected.

Customizing Machine Settings

Youcancustomizethemachinesettingstoyour

preference. Press the set key q and LCD screen will show the setting mode. Press the mode key w to select the desired setting. In this mode, you can set the following machine functions.

e Buzzer sound setting r Needle stop position setting t Start up speed setting y Resetting all to default u Key position calibration

To exit the setting mode, press the set key q.

Buzzer sound setting

The buzzer sound can be turned on or off using the buzzer sound setting. The default buzzer sound setting is “ON”. Enter the setting mode. To turn off the buzzer sound, press the cursor key “ ” and the “oF” mark will blink. To turn on the buzzer sound, press the cursor key “ ” and the “on” mark will blink.

Needle stop position setting

The machine always stops with the needle in the down position except when sewing buttonholes, specialty stitches, monograms, etc. However you can select the needle stop position to up or down.

Enter the setting mode. Press the mode key to enter the needle stop position setting. The default needle stop position setting is down position “d n”. To change the needle stop position, press the cursor key “ ” and the “UP” mark will blink.

Start-up speed setting

The machine will start running slowly and the sewing speed will gradually increase to maximum when pressing the start/stop button. Youcanselectthedesiredstart-upspeedfrom1(slow)q, 2 (medium) w or 3 (high) e.

Enter the setting mode. Press the mode key twice to enter the start-up speed setting. The default start-up speed setting is “1” (slow). To change the start-up speed, press the cursor key “ ” or “ ”, and the selected speed number will blink.

Resetting all to default

The following customized settings can be reset to the original settings (factory settings).

•Buzzersound

•Needlestopposition

•Startupspeedsetting

Enter the setting mode. Press the mode key 3 times to enter the Resetting all to default mode. Press and hold the clear key until the machine beeps to reset the machine to the factory default setting.

+ 64 hidden pages