Jaguar XF 2009 20011 User Manual

No: JTB00232

TECHNICAL BULLETIN

SERVICE PARTS WARRANTY BODY SHOP

9 9 9 9

Issue: 1 Date: 16 AUG 2011

SECTION: 415

Bluetooth® Connectivity

AFFECTED VEHICLE RANGE:

XF (X250) VIN: R15005 - S04718

Model Year: 2009 - 2011

XK (X150) VIN: B27897 - B42719

Model Year: 2008 - 2011

CONDITION SUMMARY:

Situation: A previously-paired Bluetooth® telephone may fail to auto-connect to the vehicle on engine start up and also not manually connect for the duration of that ignition cycle. This may be caused by the Bluetooth

NOTE: The customer's telephone must be listed on the Jaguar Bluetooth® Compatibility website (Canada will only improve the telephone start-up sequence, ensuring a greater chance of auto-connectivity to the vehicle.

Action: In the event of a customer concern of the above, refer to the Repair Procedure outlined below to

update the Bluetooth

PARTS:

No parts necessary

TOOLS:

IDS with latest IDS-DVD and Calibration File; first available on IDS-DVD126_0.2 Calibration File 77 Jaguar-approved Midtronics Vehicle Power Supply

WARRANTY:

telephone control module software.

or USA). The software update listed below does not affect the telephone compatibility and

telephone control module software.

NOTE: Repair procedures are under constant review, and therefore times are subject to change; those quoted here must be taken as guidance only. Always refer to DDW to obtain the latest repair time.

DDW requires the use of causal part numbers. Labor only claims must show the causal part number with a quantity of zero.

DESCRIPTION SRO TIME

Update telephone module software - XF 86.99.70

Update telephone module software - XK 86.99.70

(HOURS)

0.50

0.40

CONDITION

CODE

CAUSAL

PART

C2Z18541

C2P20239

Normal Warranty policies and procedures apply

NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools, and equipment required to do the job properly and safely. It informs these Technicians of conditions that may occur on some vehicle s, or provides information that could assist in proper vehicle service. The procedures should not be performed by 'do-it-yourselfers'. If you are not a Dealer, do not assume that a condition described affects your vehicle. Contact an authorized Jaguar service facility to determine whether this bulletin applies to a specific vehicle.

TECHNICAL BULLETIN

Issue: 1

REPAIR PROCEDURE

UPDATE THE BLUETOOTH® TELEPHONE CONTROL MODULE SOFTWARE

CAUTION: Ensure all ignition 'ON' / ignition 'OFF' requests are carried out; failure to perform

these steps may cause damage to control modules in the vehicle.

CAUTION: A Jaguar-approved Midtronics Vehicle Power Supply must be connected to the vehicle

battery during IDS diagnosis / module programming.

1. Connect the Jaguar-approved Midtronics Vehicle Power Supply to the vehicle battery.

2. Turn ignition 'ON' (engine not running).

NOTE: IDS must be loaded with IDS-DVD126_0.2 or later and Calibration File 77 or later.

3. Connect the IDS to the vehicle and begin a new Symptom Driven Diagnostics (SDD) session.

4. Follow the on-screen prompts, allowing SDD to read the VIN and identify the vehicle.

5. From the Session Type selection screen, choose 'Diagnosis'.

6. Select the 'Selected Symptoms' tab, and then select:

• Electrical > Information and entertainment system > Telephone system

7. Select 'continue'.

8. Select the 'Recommendations' tab.

No: JTB00232

9. From the Recommendations tab, select 'Run' to configure the 'Cellular telephone control module' (Bluetooth

• Follow all on-screen instructions to complete this task.

10. Exit the current session.

11. Disconnect the IDS and the Midtronics Vehicle Power Supply from the vehicle.

telephone module).

Page 2 of 2