Intel MB898, MB898F, MB898RF User Manual

1.24 Mb
Loading...

MB898/MB898F/

MB898RF

Socket LGA775 Pentium® 4

Intel® Q965 Chipset

Industrial Motherboard

USER’S MANUAL

Version 1.0

Acknowledgments

Award is a registered trademark of Award Software International, Inc.

PS/2 is a trademark of International Business Machines Corporation.

Intel and Pentium 4 are registered trademarks of Intel Corporation.

Microsoft Windows is a registered trademark of Microsoft Corporation.

Winbond is a registered trademark of Winbond Electronics Corporation.

All other product names or trademarks are properties of their respective owners.

Table of Contents

 

Introduction .......................................................

1

Checklist..............................................................................

1

Product Description.............................................................

2

Specifications ......................................................................

3

Board Dimensions ...............................................................

4

Installations .......................................................

5

Installing the CPU ...............................................................

6

ATX Power Installation ......................................................

6

Installing the Memory .........................................................

7

Setting the Jumpers .............................................................

8

Connectors on MB898 ......................................................

12

Watchdog Timer Configuration ........................................

24

BIOS Setup.......................................................

29

Drivers Installation ......................................

49

Intel Q965 Chipset Software Installation Utility...............

50

Intel Q965 Chipset Graphics Driver..................................

52

Realtek Codec Audio Driver Installation ..........................

54

Intel LAN Drivers Installation ..........................................

55

Appendix ...........................................................

57

A. I/O Port Address Map...................................................

57

B. Interrupt Request Lines (IRQ)......................................

58

MB898 User’s Manual

iii

This page is intentionally left blank.

iv

MB898 User’s Manual

INTRODUCTION

Introduction

Checklist

Your MB898/MB898F Pentium® 4 motherboard package should include the items listed below:

The MB898/MB898F motherboard

This User’s manual

1 Back I/O shield

1 IDE cable

1 Floppy cable

1 SATA cable

1 Serial-Port cable

1 CD containing the following:

Chipset Drivers

Flash Memory Utility

MB898 User’s Manual

1

INSTALLATIONS

Product Description

The MB898/MB898F LGA 775 Pentium® 4 motherboard incorporates the Intel Q965 chipset that can utilize a single LGA775 processor of up to 4.0GHz or higher and supports FSB frequency of 533/800/1066Mhz (133MHz(533MT/s), 200MHz(800MT/s) and 266MHz(1066MT/s)

HCLK respectively.

The Q965 chipset is designed for use with the Pentium® 4 processor with 1M Level 2 (CPU integrated) cache. The integrated GMCH component provides the CPU interface, DDR2 interface, Hub Interface and PCI Express graphics interface.

Four DDR2 memory sockets supports DDR2 400/533/667/800 SDRAM DIMM modules of up to 8GB in capacity.

The board is designed with one Intel 82566DC PCI Express Gigabit PHY (MB898F/RF only) or 82562V 10/100 PHY (MB898 only) LAN controllers. Serial ATA connectors offer 3Gb/s data throughput speed - faster than the most advanced parallel ATA.

Expansion is provided by four PCI slots, two PCI Express x1 and one PCI Express x16. Other advanced features include ten USB 2.0 ports, IrDA interface, digital I/O, four serial ports, watchdog timer and audio function. Dimensions of the board are 12” by 9.5” in an ATX form factor.

Remarks: MB898/MB898F supports Intel Core 2 Duo Dual Core

CPU, Pentium® D Dual Core CPU and Pentium® 4 HT single core CPU. It also supports EMT64 processors.

MB898RF supports six Serial ATA connectors (with RAID function). MB898 and MB898F support four Serial ATA connectors only.

2

MB898 User’s Manual

INTRODUCTION

Specifications

MB898/MB898F

Socket LGA775 Pentium® 4 ATX Motherboard w/ Intel® Q965 Chipset Features

Supports Intel Core 2 Duo / Pentium® D / Pentium® 4 HT / Celeron® D processors Up to 3.8GHz+, 533MHz/800MHz/1066MHz FSB

DDR2 DIMM x 4, max. 8GB

ICH8 10/100 or Intel PCI Express Gigabit Ethernet

Integrated Intel® Q965 VGA, CRT support

4 x SATA II, 10 x USB 2.0, 4 x COM, Watchdog timer, Digital I/O

(MB898RF supports 6 x SATA with RAID)

4 x PCI, 2 x PCI Express (x1), 1 x PCI Express (x16) slots

System

CPU

 

 

Socket LGA775 for Intel Core 2 Duo / Pentium® D / Pentium® 4

 

 

 

HT / Celeron® D, up to 3.8GHz+

System Memory

 

 

DDRII DIMM x 4, max. 8GB, 533/667/800MHz

System Chipset

 

 

Intel® Q965 + ICH8, 533MHz/800MHz/1066MHz FSB

BIOS

 

 

Award 8Mbit

Watchdog Timer

 

 

256 levels

SSD

 

 

NA

H/W Monitor

 

 

Yes

Expansion Slot

 

 

4 PCI, 2 PCI Express (x1), 1 PCI Express (x16)

Graphics

 

 

 

VGA Controller

 

 

Intel® Q965 integrated

VGA Memory

 

 

Shared memory

 

 

 

Max. 224MB

LCD Interface

 

 

N/A

Ethernet

 

 

 

Controller

 

 

ICH8 integrated with 82562V PHY 10/100 or

 

 

 

Intel 82566DC PCI Express Gigabit LAN (on

 

 

 

MB898F/MB898RF)

Connector

 

 

One RJ-45 on board

Multi I/O

 

 

 

Chipset

 

 

ICH8, Winbond 83627EHF, Fintek F81216

 

 

 

1x IDE (UDMA33/66/100), 1x FDD, 1x KB, 1x Mouse

 

 

 

4x RS-232, 4x SATA II (300MB/s)

 

 

 

MB898RF supports 6x SATA II with RAID function

USB

 

 

4 ports on board

 

 

 

Pin header for 6 ports (USB 2.0)

Audio

 

 

Built-in audio + AC97 codec

Others

 

 

IrDA, 4-in/4-out digital I/O

Mechanical and Environmental

Dimensions

 

 

305mm x 244mm (12“ x 9.6“)

Max. Power Requirement

 

 

TBC

Operating Temperature

 

 

0°C~60°C (32°F~140°F)

Storage Temperature

 

 

-20°C~80°C (-68°F~176°F)

Relative Humidity

 

 

10%~90% (non-condensing)

Remarks: MB898/MB898F supports Intel Core 2 Duo Dual Core CPU, Pentium® D Dual Core CPU and Pentium® 4 HT single core CPU. It also supports EMT64 processors.

MB898 User’s Manual

3

INSTALLATIONS

Board Dimensions

4

MB898 User’s Manual

INSTALLATIONS

Installations

This section provides information on how to use the jumpers and connectors on the MB898/MB898F in order to set up a workable system. The topics covered are:

Installing the CPU........................................................................

6

ATX Power Installation ...............................................................

6

Installing the Memory..................................................................

7

Setting the Jumpers ......................................................................

8

Connectors on MB898/MB898F................................................

12

Watchdog Timer Configuration .................................................

24

MB898 User’s Manual

5

INSTALLATIONS

Installing the CPU

The MB898/MB898F motherboard supports an LGA 775 processor socket for Intel® Pentium® 4 processors.

The LGA 775 processor socket comes with a lever to secure the processor. Refer to the pictures below, from left to right, on how to place the processor into the CPU socket. Please note that the cover of the

LGA775 socket must always be installed during transport to avoid damage to the socket.

ATX Power Installation

The system power is provided to the motherboard with the ATX1 and ATX_12V power connectors. ATX1 is a 24-pin power connector and ATX_12V is a 8-pin 12V power connector.

The 24-pin power connector can to be connected to a standard 20-pin ATX power connector in a standard ATX power supply (Min. 400watt).

Note: The power supply 5VSB voltage must be at least 2A.

6

MB898 User’s Manual

INSTALLATIONS

Installing the Memory

The MB886/MB898F motherboard supports four DDR2 memory sockets for a maximum total memory of 8GB in DDR memory type. It supports DDR2 533/667/800.

Basically, the system memory interface has the following features: Supports two 64-bit wide DDR data channels

Available bandwidth up to 6.4GB/s (DDR2 800) for single-channel mode and 12.8GB/s (DDR2 800) in dual-channel mode.

Supports 256Mb, 512Mb, 1Gb DDR2 technologies. Supports only x8, x16, DDR2 devices with four banks Supports only unbuffered DIMMs

Supports opportunistic refresh

Up to 32 simultaneously open pages (four per row, four rows maximum)

Dual Channel Memory Configuration

If you want to operate the Dual Channel Technology, please note the following explanations due to the limitation of Intel chipset specifications.

1.Dual Channel mode will not be enabled if only one DDR II memory module is installed.

2.To enable Dual Channel mode with two or four memory modules (it is recommended to use memory modules of identical brand, size, chips, and speed), you must install them into DIMM sockets of the same color. The following is a Dual Channel Memory configuration table:

(DS: Double Side, SS: Single Side)

 

DDRII1

DDRII2

DDRII3

DDRII4

2MemoryModules

DS/SS

X

DS/SS

X

 

X

DS/SS

X

DS/SS

4MemoryModules

DS/SS

DS/SS

DS/SS

DS/SS

MB898 User’s Manual

7

INSTALLATIONS

Setting the Jumpers

Jumpers are used on MB898/MB898F to select various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your needs. The following lists the connectors on MB898/MB898F and their respective functions.

Jumper Locations on MB898/MB898F ..........................................

9

JP8, JP9, JP10: RS232/422/485 (COM2) Selection .....................

10

JP6: IDE DMA Mode Setting.......................................................

11

JBAT1: Clear CMOS Contents.....................................................

10

JP1: Boot Device Selection………………..……………………..11

JP5: Configure and Recovery…………………………………… 11

JP11: Processor Setting.................................................................

11

8

MB898 User’s Manual

INSTALLATIONS

Jumper Locations on MB898/MB898F

 

Jumper Locations on MB898/MB898F..........................................

9

JP8, JP9, JP10: RS232/422/485 (COM2) Selection.....................

10

JP6: IDE DMA Mode Setting.......................................................

11

JBAT1: Clear CMOS Contents ....................................................

10

JP1: Boot Device Selection………………..……………………..11

JP5: Configure and Recovery…………………………………… 11

JP11: Processor Setting ................................................................

11

MB898 User’s Manual

9

INSTALLATIONS

JBAT1: Clear CMOS Contents

Use JBAT1, a 3-pin header, to clear the CMOS contents. Note that the ATX-power connector should be disconnected from the motherboard before clearing CMOS.

JBAT1

Setting

Function

 

Pin 1-2

Normal

 

Short/Closed

 

 

 

Pin 2-3

Clear CMOS

 

Short/Closed

 

 

JP1: Select the Boot Device (Factory used only)

JP1

Setting

Boot Device

 

Pin 1-2

SPI

 

Short/Closed

 

 

 

Pin 1-2

FWH (default)

 

Open

 

 

JP5: Configure and Recovery (Factory use only)

JBAT1

Setting

Function

 

Pin 1-2

Configure

 

Short/Closed

 

 

 

Pin 2-3

 

 

Short/Closed

Normal (default)

 

Open

Recovery

 

 

10

MB898 User’s Manual

 

 

INSTALLATIONS

JP6: IDE DMA Mode Setting

 

JP6

Setting

Function

 

Pin 1-2

Master (default)

 

Short/Closed

 

 

 

Pin 1-2

Slave

 

Open

 

 

JP8, JP9, JP10: RS232/422/485 (COM2) Selection

COM1 is fixed for RS-232 use only.

COM2 is selectable for RS232, RS-422 and RS-485. COM3 and COM4 are fixed for RS-232 use only. The following table describes the jumper settings for COM2 selection.

 

 

 

 

 

 

 

COM2

 

RS-232

 

 

RS-422

 

RS-485

 

 

 

 

 

 

 

Function

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

JP10:

 

 

JP10:

 

JP10:

 

 

 

 

 

 

 

Jumper

 

1-2

3-4

 

5-6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Setting

 

JP9:

 

 

JP9:

 

JP9:

 

 

 

 

 

(pin closed)

 

3-5 & 4-6

1-3 & 2-4

 

1-3 & 2-4

 

 

 

 

 

 

 

 

 

 

JP8:

 

 

JP8:

 

JP8:

 

 

 

 

 

 

 

 

 

 

3-5 & 4-6

1-3 & 2-4

 

1-3 & 2-4

 

 

 

 

 

 

 

 

 

[

 

 

 

 

 

 

JP11: Processor Setting

 

 

 

 

 

 

 

 

 

JP11

 

 

Setting

 

 

Processor Used

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pin 1-2

 

 

Celeron D

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Short/Closed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pin 1-2

 

 

Core 2 Duo,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Open

 

 

Pentium D,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Pentium 4 HT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MB898 User’s Manual

11

INSTALLATIONS

Connectors on MB898

The connectors on MB898/MB898F allows you to connect external devices such as keyboard, floppy disk drives, hard disk drives, printers, etc. The following table lists the connectors on MB898 and their respective functions.

ATX1: 24-pin ATX Power Connector.................................................

14

ATX2: ATX 12V Power Connector ....................................................

14

MB898/MB898F Edge Connectors .....................................................

14

VGA1: VGA CRT Connector..............................................................

15

CN1: Parallel Port Connector ..............................................................

15

CN2, J10, J6, J5: COM1/2/3/4 Serial Ports .........................................

16

CN3: PS/2 Keyboard and PS/2 Mouse Connectors .............................

16

CN4: Audio Connector ........................................................................

17

USB6: USB6/7 Connector ...................................................................

17

USB_LAN1: 10/100 or GbE RJ-45 and USB4/5 Connector...............

17

F_USB1: USB0/USB1 Connector .......................................................

17

F_USB2: USB2/USB3 Connector .......................................................

18

F_USB3: USB8/USB9 Connector .......................................................

18

S_ATA1,S_ATA2,S_ATA3,S_ATA4,S_ATA5,S_ATA6:

 

SATA0/1/2/3/4/5 Connector..............................................

18

Note: S_ATA5 and S_ATA6 MB898F only .......................................

18

IDE1: Primary IDE Connectors...........................................................

19

CPU_FAN1: CPU Fan Power Connector...........................................

19

PWR_FAN1: POWER Fan Power Connector....................................

19

SYS_FAN1: SYSTEM Fan Power Connector ...................................

20

NB_FAN1: Northbridge Fan Power Connectors.................................

20

J1: Audio Front Header .......................................................................

20

J2: HDMI Audio Connector ................................................................

20

J8: System Function Connector ...........................................................

21

J11: IrDA Connector............................................................................

22

J12: Digital I/O Connector (4 in, 4 out)...............................................

23

PCIE_1: x16 PCI Express Slot ............................................................

23

PCIE_2, PCIE_3: x1 PCI Express Slots ..............................................

23

PCI1, PCI2, PCI3, PCI4: PCI Slots .....................................................

23

J9: CF Socket.......................................................................................

23

12

MB898 User’s Manual

+ 46 hidden pages