Integra DSR-4.8 User Manual

DVD Receiver
DSR-4.8
Instruction Manual
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Important Safety Instructions
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons. The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
AVIS
RISQUE DE CHOC ELECTRIQUE
NE PAS
OUVRIR
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radia­tors, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are pro­vided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience recepta­cles, and the point where they exit from the appara­tus.
11. Only use attachments/accessories specified by the manufacturer.
12.
Use only with the cart, stand,
PORTABLE CART WARNING
tripod, bracket, or table spec­ified by the manufacturer, or sold with the apparatus. When a cart is used, use cau­tion when moving the cart/ apparatus combination to
S3125A
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. Damage Requiring Service
Unplug the apparatus from the wall outlet and refer servic­ing to qualified service personnel under the following con­ditions:
A. When the power-supply cord or plug is dam-
aged,
B. If liquid has been spilled, or objects have fallen
into the apparatus,
C. If the apparatus has been exposed to rain or
water,
D. If the apparatus does not operate normally by
following the operating instructions. Adjust only those controls that are covered by the oper­ating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified tech­nician to restore the apparatus to its normal operation,
E. If the apparatus has been dropped or damaged in
any way, and
F. When the apparatus exhibits a distinct change in
performance this indicates a need for service.
16. Object and Liquid Entry
Never push objects of any kind into the apparatus through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. The apparatus shall not be exposed to dripping or splash­ing and no objects filled with liquids, such as vases shall be placed on the apparatus.
Don’t put candles or other burning objects on top of this unit.
17. Batteries
Always consider the environmental issues and follow local regulations when disposing of batteries.
18. If you install the apparatus in a built-in installation, such as a bookcase or rack, ensure that there is ade­quate ventilation.
Leave 20 cm (8") of free space at the top and sides and 10 cm (4") at the rear. The rear edge of the shelf or board above the apparatus shall be set 10 cm (4") away from the rear panel or wall, creating a flue-like gap for warm air to escape.
2
Precautions
1. Recording Copyright—Unless it’s for personal use only, recording copyrighted material is illegal with­out the permission of the copyright holder.
2. AC Fuse—The AC fuse inside the unit is not user­serviceable. If you cannot turn on the unit, contact the dealer from whom you purchased this unit.
3. Care—Occasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild deter­gent and water. Dry the unit immediately afterwards with a clean cloth. Don’t use abrasive cloths, thin­ners, alcohol, or other chemical solvents, because they may damage the finish or remove the panel let­tering.
4. Power WARNING
BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SEC­TION CAREFULLY.
AC outlet voltages vary from country to country. Make sure that the voltage in your area meets the voltage requirements printed on the unit’s rear panel (e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).
The power cord plug is used to disconnect this unit from the AC power source. Make sure that the plug is readily operable (easily accessible) at all times.
Pressing the [Standby/On] button to select Standby mode does not fully shutdown the unit. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet.
5. Never Touch this Unit with Wet Hands—Never handle this unit or its power cord while your hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by the dealer from whom you purchased this unit.
6. Handling Notes
• If you need to transport this unit, use the original
packaging to pack it how it was when you origi­nally bought it.
• Do not leave rubber or plastic items on this unit
for a long time, because they may leave marks on the case.
• This unit’s top and rear panels may get warm
after prolonged use. This is normal.
• If you do not use this unit for a long time, it may
not work properly the next time you turn it on, so be sure to use it occasionally.
• When you’ve finished using this unit, remove all
discs and turn off the power.
7. Installing this Unit
• Install this unit in a well-ventilated location.
• Ensure that there’s adequate ventilation all
around this unit, especially if it’s installed in an audio rack. If the ventilation is inadequate, the unit may overheat, leading to malfunction.
• Do not expose this unit to direct sunlight or heat sources, because its internal temperature may rise, shortening the life of the optical pickup.
• Avoid damp and dusty places, and places subject to vibrations from loudspeakers. Never put the unit on top of, or directly above a loudspeaker.
• Install this unit horizontally. Never use it on its side or on a sloping surface, because it may cause a malfunction.
• If you install this unit near a TV, radio, or VCR, the picture and sound quality may be affected. If this occurs, move this unit away from the TV, radio, or VCR.
8. To Obtain a Clear Picture—This unit is a high­tech, precision device. If the lens on the optical pickup, or the disc drive mechanism becomes dirty or worn, the picture quality may be affected. To maintain the best picture quality, we recommend regular inspection and maintenance (cleaning or worn part replacement) every 1,000 hours of use depending on the operating environment. Contact the dealer from whom you purchased this unit for details.
9. Moisture Condensation Moisture condensation may damage this unit.
Read the following carefully: Moisture may condense on the lens of the optical pickup, one of the most important parts inside this unit.
• Moisture condensation can occur in the following
situations: – The unit is moved from a cold place to a warm
place.
– A heater is turned on, or cold air from an air
conditioner is hitting the unit.
– In the summer, when this unit is moved from
an air conditioned room to a hot and humid place.
– The unit is used in a humid place.
• Do not use this unit when there’s the possibility
of moisture condensation occurring. Doing so may damage your discs and certain parts inside
this unit. If condensation does occur, remove all discs and leave this unit turned on for two to three hours. By this time, the unit will have warmed up and any con­densation will have evaporated.
3
Precautions—Continued
10. Region Numbers—The DVD standard uses region numbers to control how discs can be played around the world, the world being divided into six regions. This unit will only play DVD discs that match its region number, which can be found on its rear panel
ALL
1
(e.g., , ).
11. About this Manual—This manual explains how to use all of this unit’s functions. Although the DVD standard offers many special features, not all discs use them all, so depending on the disc being played, this unit may not respond to certain functions. See the disc’s sleeve notes for supported features.
This unit contains a semiconductor laser system and is classified as a “CLASS 1 LASER PRODUCT”. So, to use this model properly, read this Instruction Manual carefully. In case of any trouble, please contact the store where you purchased the unit.
To prevent being exposed to the laser beam, do not try to open the enclosure.
CAUTION:
CLASS 1M VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS.
THIS PRODUCT UTILIZES A LASER. USE OF CON­TROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECI­FIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
For U.S. models
FCC Information for User
CAUTION:
The user changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer­ence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accor­dance with the instructions, may cause harmful interfer­ence to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful inter­ference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dif­ferent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV techni­cian for help.
The label on the right is applied on the rear panel.
1. This unit is a CLASS 1 LASER PRODUCT and employs a laser inside the cabinet.
2. To prevent the laser from being exposed, do not remove the cover. Refer servicing to qualified person­nel.
4
For Canadian Models
NOTE: THIS CLASS B DIGITAL APPARATUS
COMPLIES WITH CANADIAN ICES-003. For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
Modèle canadien
REMARQUE: CET APPAREIL NUMÉRIQUE DE
LA CLASSE B EST CONFORME À LA NORME NMB-003 DU CANADA.
Sur les modèles dont la fiche est polarisée:
ATTENTION: POUR ÉVITER LES CHOCS ÉLEC-
TRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRE­SPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
Thank you for purchasing an Integra DVD receiver. Read this manual carefully before using your new DVD receiver. A good understanding of its features and oper­ation will allow you to achieve optimum performance and enjoyment.
Keep this manual for future reference.
Supplied Accessories
Make sure you have the following accessories:
RC-705S
Remote controller & 2 batteries (AA/R6)
Video cable (RCA) (1.5 m)
Indoor FM antenna
AM loop antenna
Power cord
* In catalogs and on packaging, the letter at the end of
the product name indicates the color. Specifications and operations are the same regardless of color.
5
Introduction
Features
Highlights
•Dolby*1 Digital, DTS
• DVD-Video, Video CD, audio CD
•MP3, WMA
*3
, JPEG
• DVD-Audio and Super Audio CD
• CD-R/RW, DVD-R/RW, and DVD+R/RW com­patible
• HDMI
*4
digital interface
*2
Video
• HDMI Pass-Thru (1080p Compatible; 1 Input/1 Output)
• HDTV-Capable (50 MHz)
• JPEG in High Definition
• Advanced 108 MHz/14-bit video D/A converter
• 2 Composite Video Inputs
• Component and composite video outputs
• Repeat/A-B Repeat/Random/Memory playback
• Supports 4:3 and 16:9 aspect ratio TVs
• Three view modes providing a best-fit picture regard­less of TV aspects
• Picture Zoom Function
• Parental Lock function
• Screen Saver function
Audio
• 192 kHz/24-bit D/A converter
• 2 Digital Inputs (1 Optical/1 Coaxial)
• Theater-Dimensional
•Direct Mode
• Dynamic Range Control setting
*5
Virtual Surround
*1
Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories.
*2
“DTS” is a registered trademark of DTS, Inc. and “96/24” is a trademark of DTS, Inc.
*3
Windows Media, and the Windows logo are trademarks, or reg­istered trademarks of Microsoft Corporation in the United States and/or other countries.
*4
HDMI, the HDMI logo and High-Definition Multimedia Inter­face are trademarks or registered trademarks of HDMI licens-
ing LLC. *5 “Theater-Dimensional” is a trademark of Onkyo Corporation. * “Xantech” is a registered trademark of Xantech Corporation. * “Niles” is a registered trademark of Niles Audio Corporation. * Apple and iPod are trademarks of Apple, Inc., registered in the
U.S. and other countries.
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited consumer uses only unless otherwise authorized by Macrovision. Reverse engineering or disassem­bly is prohibited.
Others
• Compatible with RI Dock for iPod
• A/V Sync Control Function (up to 100 ms)
• 40 AM/FM Presets
• IR Input and Output
• RS232 Port for Interface Control
• 1/4-inch phone jack
• Aluminum Front Panel, Volume and Input Selector Knob
• Adjustable display brightness
6
Contents
Overview
Important Safety Instructions .................................... 2
Precautions ............................................................... 3
Supplied Accessories................................................ 5
Introduction ............................................................... 6
Features ................................................................ 6
Disc Notes............................................................. 8
Before Using the DVD receiver ............................... 11
Installing the Batteries ......................................... 11
Using the Remote Controller ............................... 11
Front & Rear Panels................................................ 12
Front Panel.......................................................... 12
Display................................................................. 13
Rear Panel .......................................................... 14
Remote Controller ............................................... 15
Connections
Connecting the DVD receiver.................................. 17
Placing the Speakers .......................................... 17
Connecting Your Speakers ................................. 17
Connecting Antenna............................................ 18
AV Cables & Connectors..................................... 21
Video Output/Video Setting Matrix ...................... 22
Video Signal Flow Chart...................................... 22
Before Making Any Connections ......................... 23
Basic Setup ......................................................... 23
Connecting Your TV (video connection).............. 24
Connecting Other AV Component....................... 24
Connecting an RI Dock ....................................... 25
Digital Audio Connection ..................................... 25
Connecting your HDTV or AV component
with an HDMI connection.................................. 26
Using the Multiroom Control Kits......................... 27
Connecting the Power/Turning
on the DVD receiver ............................................. 28
Playback Techniques
Advanced Playback................................................. 43
Selecting Chapters/Titles/Tracks/Folders by
Number .............................................................43
Searching by Time............................................... 44
Repeat Playback ................................................. 45
A-B Repeat Playback .......................................... 45
Random Playback ............................................... 46
Memory Playback ................................................ 47
Last Memory........................................................ 48
Zooming............................................................... 49
Selecting Camera Angles .................................... 49
Selecting Soundtracks......................................... 50
Selecting Subtitles ............................................... 50
Advanced Operations
Disc and Input Information ...................................... 51
Displaying Information ......................................... 51
Controlling Other Components................................ 52
Controlling a TV connected
to the DVD receiver........................................... 52
Controlling an Apple iPod in RI Dock
connected to the DVD receiver ......................... 53
Detailed Settings
Configuring the DVD receiver.................................. 54
Setup Menu ......................................................... 54
DVD Onscreen Setup Menus .................................. 57
Using the Onscreen Setup Menus....................... 58
Picture Menu ....................................................... 59
Audio Menu ......................................................... 61
Language Menu................................................... 61
Display Menu....................................................... 63
Operation Setting Menu....................................... 64
Getting Started and Setting up
Initial Setup ............................................................. 29
First Time Setup .................................................. 29
HDMI and Progressive Settings .............................. 30
Setting the HDMI ................................................. 30
Selecting Progressive or Interlaced..................... 30
Basic Operations
Understanding Common Operations....................... 31
Adjusting the Volume .......................................... 31
Selecting the Input Source .................................. 31
Using Headphones.............................................. 31
Muting the DVD receiver ..................................... 32
Using the Sleep Timer......................................... 32
Adjusting Subwoofer Level.................................. 32
Playing Discs........................................................... 33
Starting, Pausing & Stopping Playback............... 33
Select Next & Previous track/chapter.................. 34
Fast Forward & Reverse ..................................... 35
Forward Frame-by-Frame Playback.................... 35
Navigating DVD & VCD Disc Menus ................... 36
Navigating CDs & Super Audio CDs ................... 36
Navigating MP3 & WMA Discs ............................ 37
Viewing a Slideshow of JPEG Images ................ 38
Listening to the Radio ............................................. 39
Using the Tuner................................................... 39
Presetting AM/FM Stations.................................. 40
Using the Listening Modes...................................... 41
Selecting Listening Modes .................................. 41
About the Listening Modes.................................. 41
Miscellaneous information
Additional information.............................................. 66
Resetting the receiver.......................................... 66
DVD-Video regions.............................................. 66
Disc Content Organization................................... 66
Glossary ..................................................................67
Troubleshooting....................................................... 69
Power .................................................................. 69
Audio ................................................................... 69
Video ................................................................... 70
Tuner ................................................................... 71
Remote Controller ............................................... 71
Disc Playback ...................................................... 71
Connection with External Devices ....................... 72
HDMI Status Mode ..............................................73
Specifications .......................................................... 74
Remote Control Codes List
The end of this manual
7
Introduction—Continued
Disc Notes
Supported Discs
The DVD receiver supports the following discs.
Disc Logo Format or file type
DVD-Video
DVD-Aud io DVD-Audio
Super Audio CD
*2
DVD-R
DVD-RW
Video CD Including PBC
Audio CD
CD-R
CD-RW
*2
*3
*2
*2
*1
Super Audio CD (single layer, dual layer, hybrid)
DVD-Video, MP3, WMA, JPEG
DVD-Video, MP3, WMA, JPEG
PCM
Audio CD, MP3, WMA, JPEG
Audio CD, MP3, WMA, JPEG
• The DVD receiver does not support disc types not listed.
• The DVD receiver supports 8 cm and 12 cm discs.
• Don’t use discs with an unusual shape, such as those shown below, because you may damage the DVD receiver.
• Don’t use discs that have residue from adhesive tape, rental discs with peeling labels, or discs with custom­made labels or stickers. Doing so may damage the DVD receiver and you may not be able to remove the disc properly.
About playing copy-controlled CDs
Some copy-controlled CDs may not conform to official CD standards. They are special discs and may not play on the DVD receiver.
Function Support
The following icons are used throughout this manual to indicate which functions can be used with the various disc formats and file types.
Icon Disc format or file type
DVD-V
DVD-A
DVD-Video
DVD -Audio
JPEG CD JPEG
– DVD+R/RW – The DVD receiver supports DVD+R/RW discs recorded in the following formats:
• Discs recorded in DVD-Video mode.
• Discs recorded in ISO 9660 Level 2 or Joliet format containing MP3, WMA, or JPEG files.
*1 The DVD receiver’s region number is printed on the rear panel.
If you attempt to play a disc intended for another region, the message appears onscreen.
*2 MP3, WMA, and JPEG files are supported on discs recorded in
ISO 9660 Level 2 or Joliet format. (See “MP3/WMA/JPEG Compatibility” on page 9 for more details.) However, some CD-R, CD-RW, DVD-R, and DVD-RW discs may not work properly for any of the following reasons: incomplete disc finalization, disc burner charac teristics, disc characteristics, the disc is damaged or dirty, the disc contains only a small amount of data. Discs that contain different types of files, JPEG, MP3, WMA, and so on, are not supported. See the manual supplied with your disc burner for more information. Condensation or dirt on the optical pickup lens can also affect playback.
*3 Some audio CDs feature copy protection that doesn’t conform
to the official CD standard. Since these are nonstandard discs, they may not play properly in the DVD receiver.
8
SACD
VCD
CD
MP3
WMA
JPEG
Super Audio CD
Video CD
Audio CD
MP3 file
WMA file
JPEG file
About this Manual
This manual explains how to use all of the DVD receiver’s functions. Although the DVD standard offers many special features, not all discs use them all, so depending on the disc being played, the DVD receiver may not respond to certain functions. See your disc’s sleeve notes for supported features.
When you attempt to use a DVD feature that is not available, this logo may appear onscreen, indicating that the feature is not supported by the current disc or by the DVD receiver.
Introduction—Continued
MP3/WMA/JPEG Compatibility
• The DVD receiver can play/display MP3, WMA, and JPEG files recorded on CD-R, CD-RW, DVD-R, DVD-RW, DVD+R and DVD+RW discs.
• Discs must be in ISO 9660 Level 2 or Joliet format (folders can be up to eight levels deep). Music files recorded on discs that use the HFS (hierarchical file system) cannot be played.
• Discs must be finalized.
• The DVD receiver can only recognize the first session on multisession discs.
• You can determine the order in which the DVD receiver plays/displays your MP3/WMA songs and JPEG pictures by prefixing file and folder names with a three-digit number. For example 001.Root,
002.Folder, and so on, and 001.Track.mp3,
002.Track.mp3, and so on.
Only the first eight characters of folder and track names (excluding the filename extension) are displayed.
• The folder numbered “001” appears as “ROOT” in the Disc Navigator.
• The DVD receiver supports up to 255 folders and up to 255 files per folder.
• If you try to play an incompatible file, the message “This format cannot be played.” appears on the dis­play.
MP3
• MP3 files must be MPEG1 Audio Layer 3 format,
44.1 or 48 kHz, fixed bit-rate.
• MP3 files must have a “.mp3” or “.MP3” filename extension.
• Variable bit-rates (VBR) from 32 kbps to 320 kbps are supported. (Playing times may display incorrectly with VBR.)
WMA
• WMA files must have the copyright option turned off.
• Sampling rates 44.1/48 kHz are supported.
• Variable bit-rates (VBR) from 48 kbps to 192 kbps (44.1 kHz) and 128 kbps to 192 kbps (48 kHz) are supported. (Playing times may display incorrectly with VBR.)
• WMA files must have a “.wma” or “.WMA” filename extension.
JPEG
• JPEG files must have a “.jpg” or “.JPG” filename extension.
• JPEG files must be less than 5 megabytes in size.
• JPEG files up to 5,700 x 3,800 pixels are supported.
About WMA
WMA is an acronym for Windows Media Audio and refers to an audio compression technology developed by Microsoft Corporation. WMA content can be encoded by using Windows Media
®
Player version 7/7.1 or 8.
Handling Discs
• Never touch the underside of a disc. Always hold discs by the edge, as shown.
Underside
• Never attach adhesive tape or sticky labels to discs.
Cleaning Discs
• For best results, keep your discs clean. Fingerprints and dust can affect the sound and picture quality and should be removed as follows. Using a clean soft cloth, wipe from the center outwards, as shown. Never wipe in a circular direction.
• To remove stubborn dust or dirt, wipe the disc with a damp soft cloth, and then dry it with a dry cloth.
• Never use solvent-based cleaning fluids, such as thin­ner or benzine, commercially available cleaners, or antistatic sprays intended for vinyl records, because they may damage the disc.
Storing Discs
• Don’t store discs in places subject to direct sunlight, or near heat sources.
• Don’t store discs in places subject to moisture or dust, such as in a bathroom or near a humidifier.
• Always store discs in their cases and vertically. Stack­ing, or putting objects on unprotected discs may cause warping, scratches, or other damage.
9
Introduction—Continued
Copyright
It is forbidden by law to copy, broadcast, show, broad­cast on cable, play in public, or rent copyrighted material without permission.
DVD-Video discs are copy-protected, and any record­ings made from these discs will be distorted. This product incorporates copyright protection technol­ogy that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright-protection technology must be autho­rized by Macrovision Corporation, and is intended for home and other limited viewing uses only, unless other­wise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
10
Before Using the DVD receiver
Installing the Batteries
To open the battery compartment, press
1
the small hollow and slide off the cover.
Insert the two supplied batteries (AA/R6)
2
in accordance with the polarity diagram inside the battery compartment.
Put the cover onto the remote controller
3
and slide it shut.
Using the Remote Controller
To use the remote controller, point it at the DVD receiver’s remote control sensor, as shown below.
Remote control sensor
DVD rece i ve r
Approx. 16 ft. (5 m)
Notes:
• The remote controller may not work reliably if the DVD receiver is subjected to bright light, such as direct sunlight or inverter-type fluorescent lights. Keep this in mind when installing the DVD receiver.
• If another remote controller of the same type is used in the same room, or the DVD receiver is installed close to equipment that uses infrared rays, the remote con­troller may not work reliably.
• Don’t put anything, such as a book, on the remote con­troller, because the buttons may be pressed inadvert­ently, thereby draining the batteries.
• The remote controller may not work reliably if the DVD receiver is installed in a rack behind colored glass doors. Keep this in mind when installing the DVD receiver.
• The remote controller will not work if there’s an obstacle between it and the DVD receiver’s remote control sensor.
Notes:
• If the remote controller doesn’t work reliably, try replacing both batteries.
• Don’t mix new and old batteries, or different types of batteries.
• If you intend not to use the remote controller for a long time, remove the batteries to prevent possible leakage and corrosion.
• Flat batteries should be removed as soon as possible to prevent possible leakage and corrosion.
11
Front & Rear Panels
For detailed information, refer to the pages in brackets.
Front Panel

(2 (4(1 (3(5
Standby/On button [28]
This button is used to set the DVD receiver to On or Standby.
Standby indicator [28]
This indicator lights up when the DVD receiver is in Standby.
Input selector [31] and indicator
This selector is used to select from the following input sources: DVD, VIDEO 1, VIDEO 2/DOCK, FM, AM.
Disc tray [33]
Discs are loaded here.
Open/Close button [33]
This button is used to open and close the disc tray. The input source is automatically set to DVD.
Stop button [34]
This button is used to stop playback.
Play button [33]
This button is used to start playback. The input source is automatically set to DVD.
Master Volume control [31] and indicator
This control is used to adjust the volume of the DVD receiver to Min, 1 through 79, Max.
Phones jack [31]
This 1/4-inch phone jack is for connecting a stan­dard pair of stereo headphones for private listening.
(1 HDMI button [30]
This button is used to turn HDMI on or off.
(2 HDMI indicator [30]
This indicator lights up when a HDMI signal is being output.
(3 Remote control sensor [11]
This sensor receives control signals from the remote controller.
(4 Previous/Next / buttons or Tuning/
Preset / buttons [34, 39]
The Previous [ ] button is used to select the pre­vious chapter or track. During playback it selects the beginning of the current track. The Next [ ] button is used to select the next chapter or track. When the AM or FM input source is selected, these buttons are used to tune the tuner, or select radio presets.
(5 Pause button or Preset Memory button [33,
35, 40]
This button is used to pause playback. While play­back is paused, pressing this button moves the video forward one frame at a time. When the AM or FM input source is selected, this button is used to store the radio presets.
12
Front & Rear Panels—Continued
Display

(1 (2 (3
MUTING indicator
This indicator flashes while the DVD receiver is muted.
Tuning indicators
AUTO : This indicator lights up when the Auto Tun­ing mode is selected, and disappears when the Man­ual Tuning mode is selected.
: This indicator lights up when the DVD receiver is tuned into a radio station. FM ST: This indicator lights up when the DVD receiver is tuned to a stereo FM station.
Listening mode & format indicators
These indicators show the currently selected listen­ing mode and the format of the playing disc.
Playback mode indicators
MEM: Lights up when memory playback is selected.
RDM: Lights up when random playback is selected. REPEAT: Lights up when repeat playback is
selected for all the tracks. REPEAT 1: Lights up when repeat playback is selected for a track.
Disc type indicators
These indicators show the type of disc loaded.
Data type indicators
These indicators show the type of data loaded.
Disc operation indicators
These indicators show the status of disc playback.
DIGITAL indicator
This indicator lights up when the digital audio sig­nal input is used.
ANALOG indicator
This indicator lights up when the analog audio sig­nal input is used.
(1 Camera angle indicator
This indicator appears if the DVD-Video disc being played features multiple camera angles.
(4
(5
(7
(6
(8
(2 SLEEP indicator
This indicator lights up when the Sleep function has been set.
(3 GROUP indicator
While stopped, the total number of groups on the cur­rent DVD-Audio disc is displayed here. During play­back, the number of the current group is displayed.
(4 TITLE indicator
During playback, the number of the current title is displayed.
(5 Message & time area
Time information, such as total time, remaining time, and so on, is displayed here in hours, minutes, and seconds. Other messages are also displayed.
(6 CHP indicator
This indicator appears while the number of the cur­rent chapter is being displayed.
(7 TRACK indicator
This indicator appears while track numbers are being displayed. While stopped, the total number of tracks on the current SACD or audio CD are dis­played. During playback, the number of the current track is displayed.
(8 PRGSV indicator
This indicator appears when progressive video is being output by the component video output.
(9 TOTAL indicator
This indicator appears while the total number or total time is being displayed.
(: REMAIN indicator
This indicator appears while the remaining time is being displayed.
(:(9
13
Front & Rear Panels—Continued
Rear Panel
SPEAKERS [18]
These terminal posts are for connecting your front speakers.
HDMI IN/OUT [26]
HDMI (High Definition Multimedia Interface) con­nections carry digital audio and digital video. The HDMI input is for connecting components with HDMI outputs. The HDMI output is for connecting a TV or projector with an HDMI input.
COMPONENT VIDEO OUTPUT [24]
These jacks output component video and can be connected to an component video input on a TV or projector.
VIDEO OUTPUT [23]
This RCA connector can be used to connect a TV or projector with a composite video input.
FM ANTENNA [18]
This jack is for connecting an FM antenna.
AM ANTENNA [19]
These push terminals are for connecting an AM antenna.
AC INLET [28]
The supplied power cord is connected here. The other of the power cord should be connected to a suitable wall outlet.
OPTICAL DIGITAL AUDIO IN [25]
This optical digital audio input can be connected to an optical digital audio output on a DVD recorder, or game console. This input is assigned for VIDEO 1 INPUT in default. If you output audio from this input during VIDEO 2/DOCK INPUT is selected, you must change the “Video2 Input” setting to “OPT” from “Coax” (page 54).
(1(2 (4
(3
COAXIAL DIGITAL AUDIO IN [25]
(1 REMOTE CONTROL [25]
(2 VIDEO 1 INPUT [24]
(3 VIDEO 2/DOCK INPUT [25]
(4 SUBWOOFER PRE OUT [18]
(5 RS232
(6 IR IN/OUT [27]

(5 (6
This coaxial digital audio input can be connected to a coaxial digital audio output on a DVD recorder or game console. This input is assigned for VIDEO 2/DOCK INPUT in default. If you output audio from this input during VIDEO 1 INPUT is selected, you must change the “Video1 Input” setting to “Coax” from “OPT” (page 54).
This (Remote Interactive) jack can be con­nected to an jack on Onkyo RI Dock. The DVD receiver remote controller can then be used to con­trol the RI Dock. To use , you must make an analog audio connection (RCA) between the DVD receiver and the RI Dock, even if they are connected digitally.
Here you can connect other video equipment. Input jacks include composite video and analog audio input.
Here you can connect Onkyo RI DOCK or other video equipment. Input jacks include composite video and analog audio input.
A powered subwoofer can be connected here.
This port is for connecting the DVD receiver to external controllers.
A commercially available IR receiver can be con­nected to the IR IN jack, allowing you to control the DVD receiver when it’s out of sight, for example, installed in a cabinet. A commercially available IR emitter can be con­nected to the IR OUT jack to pass IR (infrared) remote control signals along to other components.
14
Front & Rear Panels—Continued
Remote Controller
  (1
(2 (3
(4
(5
(6
(7
(8
(9
(:
)1
)2
Standby/On button* [28]
This button is used to set the DVD receiver to Standby or turn on. Don’t turn on the DVD receiver until you’ve com­pleted, and double checked all connections (pages 23–27).
Number buttons* [43, 44, 64]
These buttons are used to enter title, chapter, and track numbers and to enter times for locating spe­cific points in time.
CLR button [40, 43, 44, 48]
This button is used to cancel various functions.
TV Control buttons [52]
These buttons are used to control a TV. You must enter the appropriate remote control code first.
Disc and DVD receiver menu buttons
Top Menu button* [36, 38]
With DVD discs, this button displays the main menu. With a JPEG disc, it displays thumbnails of the images. With a Video CD, it turns PBC on or off.
Menu button* [36, 38]
This button is used to display a menu on a DVD or to open the Disc Navigator when using a JPEG disc.
Cursor /// buttons* [36, 54, 58]
These buttons are used to navigate menus.
Enter button* [36, 54, 58]
This button is used to start playback of the selected title, chapter, or track, and to confirm settings.
Setup button [54, 58]
This button is used to open and close the setup menus.
Return button [54]
This button is used to return to the previous display when changing settings.
15
Front & Rear Panels—Continued
Basic Playback buttons*
Pause button [33, 35]
This button is used to pause playback. While play­back is paused, pressing this button moves the video forward one frame at a time.
Play button [33]
This button is used to start playback.
Stop button [34]
This button is used to stop playback.
Fast Reverse/Fast Forward / buttons [35]
These buttons are used for fast reverse and fast forward.
Previous/Next / buttons [34]
The Previous [ ] button is used to select the pre­vious chapter or track. During playback it selects the beginning of the current track. The Next [ ] button is used to select the next chapter or track.
Advanced Playback buttons
Audio button [50]
This button is used to select foreign language soundtracks and audio formats (e.g., Dolby Digital or DTS) on DVD-Video discs.
Subtitle button [50]
This button is used to select subtitles on DVD-Video discs.
Angle button [49]
This button is used to select camera angles on DVD-Video discs.
Random button* [46]
This button is used with the Random function.
Repeat button* [45]
This button is used to set the Repeat function.
A-B button [45]
This button is used to set the A-B Repeat function.
Display button [51]
This button is used to display information about the disc or the current input source. Press it repeatedly to display more information.
Aspect/Zoom button [49, 59]
This button is used to change the view mode. Press­ing and holding it for a few seconds selects Zoom mode.
(1 Resolution button [30]
This button is used to select a video resolution for the HDMI OUT.
(2 Sleep button [32]
This button is used with the Sleep function.
(3 Input / button [31]
This button is used to select the input sources.
(4 Search button [40, 43, 44]
This button is used to search for titles, chapters, groups, folders, tracks, and specific points in time. When the AM or FM input source is selected, you can tune into AM and FM stations directly by enter­ing the appropriate frequency.
(5 Memory button [47]
This button is used with the Memory function. When the AM or FM input source is selected, this button is used to store the radio presets.
(6 Last Memory button [48]
This button is used with the Last Memory function for DVD playback.
(7 Muting button [32]
This button is used to mute or unmute the DVD receiver.
(8 VOL / button [31]
This button is used to adjust the volume of the DVD receiver.
(9 Tuner buttons
Tuning / button [39]
When the AM or FM input source is selected, the
[]/[]
Tuning
Preset / buttons [40]
When the AM or FM input source is selected, the Preset [ ]/[ ] buttons are used to select radio pre­sets.
buttons are used to tune the tuner.
(: Mode button* [39]
This button is used to select the Auto or Manual tuning mode.
)1 Subwoofer Level button [32]
This button is used to access the Subwoofer Level menu. Use the Left and Right [ ]/[ ] buttons to adjust the volume.
)2 Listening Mode button [41]
This button is used to select the listening modes.
For buttons to control an Apple iPod in RI Dock with
*
an RI connection, see page 53.
16
Connecting the DVD receiver
Placing the Speakers
Front Left and Right Speakers
• Place the front left and right speakers symmetrically and so that the distance from the listening position is the same.
• When placing speakers, direct the speakers toward the position of the listener’s ears where the listener sits to enjoy music or movies.
• Place the two speakers so that the heights of the two speakers are aligned. The ideal height for the speakers is the height of the listener’s ears.
TV or screen
FL FR
FL: Front left speaker
FR: Front right speaker
Subwoofer
Using a subwoofer greatly improves the volume level and sound quality of bass sounds. The subwoofer effect depends not only on the listening position but also on the shape of the listening room.
• In general, place the subwoofer in a corner of the room or at a point 1/3 the width of the room.
• Play a movie or music that contains high quality bass sounds to determine the subwoofer placement. Change the subwoofer’s position and check the effect, then select the position where the bass sounds are best heard.
Connecting Your Speakers
Speaker Connection Precautions
Read the following before connecting your speakers:
• You can connect speakers with an impedance of between 6 and 16 ohms. If you use speakers with a lower impedance, and use the DVD receiver at high volume levels for a long period of time, the built-in protection circuit may be activated.
• Disconnect the power cord from the wall outlet before making any connections.
• Read the instructions supplied with your speakers.
• Pay close attention to speaker wiring polarity. In other words, connect positive (+) terminals only to positive (+) terminals, and negative (–) terminals only to nega­tive (–) terminals. If you get them the wrong way around, the sound will be out of phase and will sound unnatural.
• Unnecessarily long, or very thin speaker cables may affect the sound quality and should be avoided.
• Be careful not to short the positive and negative wires. Doing so may damage the DVD receiver.
• Make sure the metal core of the wire does not have contact with the DVD receiver’s rear panel. Doing so may damage the DVD receiver.
• Don’t connect more than one cable to each speaker terminal. Doing so may damage the DVD receiver.
• Don’t connect one speaker to several terminals.
1/3 room length
Corner
17
Connecting the DVD receiver—Continued
Connecting the Speaker Cables
Strip about 5/8" (15 mm)
1
of insulation from the ends of the speaker cables, and twist the bare wires tightly, as shown.
Unscrew the terminal.
2
Fully insert the bare
3
wires.
Screw the terminal tight.
4
The following illustration shows which speaker should be connected to each pair of terminals.
Front right speaker
5/8" (15 mm)
Front left speaker
Connecting Antenna
This section explains how to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially available outdoor FM and AM antennas.
The DVD receiver won’t pick up any radio signals with­out any antenna connected, so you must connect the antenna to use the tuner.
AM antenna push terminals
FM antenna connector
Connecting the Indoor FM Antenna
The supplied indoor FM antenna is for indoor use only.
Attach the FM antenna, as shown.
1
Insert the plug fully into the jack.
Connecting a Powered Subwoofer
Using a suitable cable, connect the DVD receiver’s SUB­WOOFER PRE OUT to an input on your powered sub­woofer, as shown.
Powered
subwoofer
LINE INPUT
Once your DVD receiver is ready for use, you’ll need to tune into an FM radio station and adjust the position of the FM antenna to achieve the best possible reception.
Use thumbtacks or something similar to
2
fix the FM antenna into position.
Thumbtacks, etc.
Caution: Be careful that you don’t injure yourself when using thumbtacks.
If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available out­door FM antenna instead (see page 19).
18
Connecting the DVD receiver—Continued
Connecting the AM Loop Antenna
The supplied indoor AM loop antenna is for indoor use only.
Assemble the AM loop antenna, inserting
1
the tabs into the base, as shown.
Connect both wires of the AM loop
2
antenna to the AM antenna push termi­nals, as shown.
The antenna connection is polarity sensitive. Con­nect the black wire to the ground terminal ( ). Connect the other wire to the other terminal. Make sure that the wires are attached securely and that the push terminals are gripping the bare wires, not the insulation.
Push Insert wire Release
Connecting an Outdoor FM Antenna
If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available out­door FM antenna instead.
Notes:
• Outdoor FM antennas work best outside, but usable results can sometimes be obtained when installed in an attic or loft.
• For best results, install the outdoor FM antenna well away from tall buildings, preferably with a clear line of sight to your local FM transmitter.
• Outdoor antenna should be located away from possi­ble noise sources, such as neon signs, busy roads, etc.
• For safety reasons, outdoor antenna should be situated well away from power lines and other high-voltage equipment.
• Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock haz­ards.
Using a TV/FM Antenna Splitter
It’s best not to use the same antenna for both FM and TV reception, as this can cause interference problems. If cir­cumstances demand it, use a TV/FM antenna splitter, as shown.
Black
Once your DVD receiver is ready for use, you’ll need to tune into an AM radio station and adjust the position of the AM antenna to achieve the best possible reception.
Keep the antenna as far away as possible from your DVD receiver, TV, speaker cables, and power cords.
If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commer­cially available outdoor AM antenna (see page 20).
TV/FM antenna splitter
To DVD receiver To TV (or VCR)
19
Connecting the DVD receiver—Continued
Connecting an Outdoor AM Antenna
If good reception cannot be achieved using the supplied AM loop antenna, an outdoor AM antenna can be used in addition to the loop antenna, as shown.
Outdoor antenna
Insulated antenna cable
AM loop antenna
Black
White
Outdoor AM antennas work best when installed outside horizontally, but good results can sometimes be obtained indoors by mounting horizontally above a window. Note that the AM loop antenna should be left connected.
Outdoor antenna must be grounded in accordance with local regulations to prevent electrical shock hazards.
20
Connecting the DVD receiver—Continued
AV Cables & Connectors
Video
Cable Jack Description
HDMI
Y
//
C
B
P
B
C
R
P
R
Component video
Y
C
B
P
B
R
P/ /
R
C
HDMI connections can carry uncompressed, stan­dard or high definition digital video and digital audio, for the best picture and sound quality.
Component video separates the luminance (Y) and color difference signals (P
R, PB), providing the best
picture quality. Some TV manufacturers label their component video inputs differently.
Composite video (supplied)
Audio
Optical digital
Coaxial digital
Analog
Composite video can be found on virtually all TVs, VCRs, and video equipment.
Cable Jack Description
Optical digital audio connections provide better audio quality than analog connections.
Coaxial digital audio connections provide better audio quality than analog connections.
RCA analog audio connectors can be found on vir­tually all AV components.
21
Connecting the DVD receiver—Continued
Video Output/Video Setting Matrix
The following matrix shows how the video outputs work in relation to the various video settings.
: Output
Setting
Video output
HDMI
Component
Composite
*1 No picture will be output from other than HDMI when you connect the TV that the native resolution is “720p” or “1080i”. *2 If your TV doesn’t support progressive scanning, you’ll get no picture. *3 If your TV doesn’t support the “HD Resolution” settings of “720p” and “1080i”, you’ll get no picture.
HD Resolution (page 30) Progressive Setting (page 30)
Auto 480p (default) 720p, 1080i Progressive Interlace
✓✓✓
*1
*1
Video Signal Flow Chart
Video input signals flow through the DVD receiver as shown. HDMI input pass through HDMI output signals as it is.
Set top box, VCR, DVD recorder, etc.
HDMI Output Setting (page 29, 30)
On (default) Off
*3
*2
No output
No output No output
*2
No output ✓✓
VIDEO 1 VIDEO 2/DOCK
HDMI
HDMI IN V IN V IN
HDMI ComponentComposite
Composite
VIDEO OUT COMPONENT OUTHDMI OUT
TV, projector, etc.
Composite
DVD
22
Connecting the DVD receiver—Continued
Before Making Any Connections
• Read the manuals supplied with your AV components.
• Don’t connect the power cord until you’ve completed all audio and video connections.
RCA AV Connection Color Coding
RCA AV connections are usually color coded: red, white, and yellow. Use red plugs to connect right-chan­nel audio inputs and outputs (typically labeled “R”). Use white plugs to connect left-channel audio inputs and out­puts (typically labeled “L”). And use yellow plugs to connect composite video inputs and outputs.
Right (red)
Left (white)
(Yellow)
Analog audio
Composite video (Supplied)
Right (red)
Left (white)
(Yellow)
Basic Setup
The setup described here is a basic setup that allows you to play discs using just the cables supplied with the receiver.
• Push each plug in all the way to make a good connection (loose
Right!
connections can cause noise or malfunctions).
• To prevent interference, keep audio and video cables away from
Wrong!
power cords and speaker cables.
Optical Digital Jacks
The DVD receiver’s optical digital connectors have a shutter-type cover that opens when an optical plug is inserted, and closes when it’s removed. Push the plug in all the way.
Caution: To prevent shutter damage, hold the optical plug straight when inserting and removing.
Video cable (Supplied)
This receiver is equipped with copy protection tech­nology. Do not connect this receiver to your TV via a VCR using Video cable, as the picture from this receiver will not appear properly on your TV. (This receiver may also not be compatible with some com­bination TV/VCRs for the same reason; refer to the manufacturer for more information.)
TV
VIDEO IN
To power outlet
Powe r cord (Supplied)
1. Connect the VIDEO OUTPUT jack to the com-
posite video input on your TV.
Use the supplied Video cable (RCA), connecting the yellow plug to the video output. See the following page if you want to use other cable for the video connection.
2. Connect the supplied AC power cord to the AC
INLET, then plug into a power outlet.
23
Connecting the DVD receiver—Continued
Connecting Your TV (video connection)
• Connect the DVD receiver directly to your TV. If you connect the DVD receiver through a VCR, TV/VCR combination, or video selector, the picture may be dis­torted because DVD-Video discs are usually copy pro­tected.
Using Component Video
You can use the component video output instead of the standard video out jack to connect this receiver to your TV (or other equipment). This will provide better quality picture than composite video.
This jack cannot output the signal from composite video input.
• Use a component video cable (not supplied) to con­nect the COMPONENT VIDEO OUTPUT jacks to a component video input on your TV (or monitor).
If you connect the component video output to a TV or another component that doesn’t support progressive scanning, be sure to turn off HDMI (see page 30). You can set the component video output to Progressive or Interlaced (see page 30).
Connecting Other AV Component
You can use an AV cable to connect VIDEO 1 INPUT L/ R or V jack to your AV component such as a set top box, VCR, and DVD recorder.
Connect your AV component’s analog audio and Video output jack to the DVD receiver’s VIDEO 1 INPUT L/R or V jack.
VIDEO
OUT
Set top box,
VCR, DVD
Recorder
Note:
You can also use optical/coaxial digital cable instead of the audio cable (see page 25).
AUDIO
OUT
LR
COMPONENT
YPB PR
VIDEO IN
Compatibility of this unit with progressive-scan TVs.
This receiver is compatible with progressive video Macro Vision System Copy Guard.
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DIS­PLAYED IN THE PICTURE. IN CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE “STAN­DARD DEFINITION” OUTPUT. IF THERE ARE QUESTIONS REGARDING OUR TV SET COM­PATIBILITY WITH THIS MODEL 525p AND 625p DVD RECEIVER, PLEASE CONTACT OUR CUS­TOMER SERVICE CENTER.
24
TV
Connecting the DVD receiver—Continued
Connecting an RI Dock
iPod with video or RI Dock with the OSD mode
Connect your RI Dock’s analog audio output jacks and Video output jack to the DVD receiver’s VIDEO 2/DOCK INPUT L/R jacks and V jack. Connect the RI Dock with an cable. (Onkyo DS-A1X/A2/A2X hookup shown below.)
iPod without video
Connect your RI Dock’s analog audio output jacks to the DVD receiver’s VIDEO 2/DOCK INPUT jacks. Connect the RI Dock with an cable. (Onkyo DS-A1 hookup shown below.)
Notes:
• Set the RI Dock’s RI MODE switch to HDD or HDD/DOCK.
• Press the Input [ ]/[ ] buttons to select “VIDEO2/DOCK”.
• Refer to the RI Dock’s instruction manual.
Digital Audio Connection
You can use optical/coaxial digital cable instead of the audio cable when connecting with other AV components. Connect your AV component’s digital audio output jack to corresponding COAXIAL or OPTICAL DIGITAL AUDIO
IN jack of the DVD receiver. You must assign that jack to an input (see page 56).
Notes:
• Optical digital audio input is assigned for VIDEO 1 INPUT in default. If you output audio from this input during VIDEO 2/ DOCK INPUT is selected, you must change the “Video2 Input” setting to “OPT” from “Coax”.
• Coaxial digital audio input is assigned for VIDEO 2/ DOCK INPUT in default. If you output audio from this input during VIDEO 1 INPUT is selected, you must change the “Video1 Input” setting to “Coax” from “OPT”.
Set top box,
VCR, DVD
Recorder
COAXIALOPTICAL
Connect one or the other
VIDEO
OUT
25
Connecting the DVD receiver—Continued
Connecting your HDTV or AV component with an HDMI connection
This section shows how to connect the DVD receiver to an HDTV, projector, or game console that has an HDMI input/output socket.
What is HDMI?
HDMI (High Definition Multimedia Interface) is a new connection format that can carry uncompressed, stan­dard or high definition digital video and digital audio. Until now, several separate video and audio cables have been required to connect AV components together. With HDMI, a single cable is all that’s necessary to achieve the best picture quality.
HDMI video is compatible with DVI (Digital Visual Interface). To send HDMI video to a DVI input requires an HDMI-to-DVI cable. The DVD receiver supports HDCP (High-bandwidth Digital Content Protection), and for an HDMI-to-DVI connection to work, the other component must also support it. Note that this may not work with some DVI components.
Using HDMI
Use the HDMI cable (not supplied) to connect the DVD receiver’s HDMI OUT to an HDMI input on your TV. In the same manner, connect the DVD receiver’s HDMI IN to an HDMI OUT on the game console, etc.
HDTV,
projector
HDMI
IN
HDMI cable (not supplied)
HDMI
IN
HDMI cable (not supplied)
HDMI
HDMI
Notes:
• The DVD receiver supports HDCP (High-bandwidth Digital Content Protection), a protection system for digital video. HDMI components that you connect to the DVD receiver must also support HDCP.
• The DVD receiver supports High-Definition Multime­dia Interface Specification Information Version 1.0.
HDMI & the DVD receiver
Video
The DVD receiver’s HDMI OUT supports the following video resolutions:
• 720 x 480p (progressive), 60 Hz
• 1280 x 720p (progressive), 50/60 Hz
• 1920 x 1080i (interlaced), 50/60 Hz
If the connected HDTV or projector doesn’t support a resolution, you may get no picture.
On the DVD receiver, you can select a resolution suit­able for use with the connected HDTV or projector (see page 30).
Audio Formats
The DVD receiver’s HDMI OUT supports the following audio formats:
• PCM (96 kHz, 48 kHz, 44.1 kHz)
• Dolby Digital
•DTS
Notes:
• If your HDMI-compatible TV or projector doesn’t support Dolby Digital and DTS, the HDMI OUT will not output digital audio in that format. In this case, set the “Digital/HDMI Audio Out” setting to “PCM” (see page 61).
• If your TV doesn’t support digital audio at high sam­pling rates, set the “Linear PCM Out” setting to “Down Sample On”, so that it’s down sampled to below 48 kHz (see page 61).
• Note that audio from SACD discs or audio from the multi channel area of a DVD-Audio discs is not output by the HDMI OUT.
• The audio signal input from HDMI IN is not output from the speakers connected to the DVD receiver but only from the TV. With some TVs and input signals, no sound may be output. In these cases, set the connected device’s out­put to PCM.
• Audio and video inputs from VIDEO 1 INPUT or VIDEO 2/DOCK INPUT are not be output from HDMI OUT.
26
Game Console, etc.
Connecting the DVD receiver—Continued
Using the Multiroom Control Kits
To control the DVD receiver with the remote controller when DVD receiver is located in a cabinet, you’ll need a commercially available multiroom remote control kit.
• Multiroom kits are made by Niles and Xantech. These kits can also be used when control other compo­nents.
Using a Multiroom Kit with a Cabinet
In this setup, the IR receiver picks up the infrared signals from the remote controller and feeds them to the DVD receiver located in the cabinet via the connecting block.
Connecting block
IR IN
DVD receiver
Inside cabinet
Signal flow
The miniplug cable from the connecting block should be connected to the DVD receiver’s IR IN jack, as shown below.
Miniplug cable
From the connecting block
IR Receiver
Remote controller
Using a Multiroom Kit with Other Components
In this setup, an IR emitter is connected to the DVD receiver’s IR OUT jack and placed in front of the other component’s remote control sensor. Infrared signals received at the DVD receiver’s IR IN jack are fed through to the other component via the IR emitter. Sig­nals picked up by the DVD receiver’s remote control sensor are not output.
Connecting block
IR IN
IR OUT
DVD receiver
IR Emitter
Other component
Signal flow
The IR emitter should be connected to the DVD receiver’s IR OUT jack, as shown below.
Other component
Miniplug cable
Miniplug
IR Receiver
Remote controller
Emitter
IR Emitter
Remote control sensor
DVD receiver
DVD receiver
Signal flow
27
Connecting the Power/Turning on the DVD receiver
Before connecting
• Make sure that all the connections on pages 17–27 are complete (the connection to a TV is required).
Standby/On
Standby indicator
Standby/On
2
DVD receiver
Remote
controller
• Before unplugging the receiver from the power outlet, make sure you first switch it into standby.
• For the above reasons, do not plug this receiver into a switched power supply found on some amplifiers and AV receivers.
To a wall outlet
Press [Standby/On] button on the DVD receiver or the remote con­troller.
Turn on your TV and select the input through which the DVD receiver is connected.
The DVD receiver turns on and the Standby indicator turns off.
• To put the DVD receiver in the standby mode, press [Standby/On] on the DVD receiver, or [Standby/On] on the remote controller.
• While the Standby indicator lights up, the DVD receiver can receive signals from the remote controller.
• Setting the [Standby/On] button to standby does not shut off the power completely.
28
1
Plug the supplied power cord into the AC INLET and then into the power outlet on the wall.
• Do not use a power cord other than the one supplied with the DVD receiver. The power cord supplied is designed for use with the DVD receiver and should not be used with any other device.
• Never have the power cord discon­nected from the DVD receiver while the other end is plugged into the wall outlet. Doing so may cause an electric shock. Always connect by plugging into the wall outlet last and disconnect by unplugging from the wall outlet first.
Note:
DVD receiver features a screen saver and an auto power off function. If the receiver is stopped and no button is pressed for 15 minutes, the screen saver starts (see page 63).
Initial Setup
This chapter explains the settings you need to make the very first time the DVD receiver is turned on.
Basically this manual contains procedures using the remote controller.
Enter
First Time Setup
The very first time you turn on the DVD receiver, the “Initial Setup” menu appears onscreen.
Initial Setup
TV Shape
HDMI Output Setting
On-Screen Language
4:3 Letter box
4:3 Pan Scan
16:9 Widescreen
16:9 Compressed
Here you need to make a few settings to get the DVD receiver up and running. You can change these settings later (see page 57).
1
Use the Up and Down [ ]/[ ] buttons to select “TV Shape”, and then press [Enter].
Select “4:3 Letter box” or “4:3 Pan Scan” if you have a 4:3 TV. Select “16:9 Widescreen” or “16:9 Com­pressed” if you have a widescreen TV. See page 59 for more information.
Initial Setup
TV Shape
HDMI Output Setting
On-Screen Language
4:3 Letter box
4:3 Pan Scan
16:9 Widescreen
16:9 Compressed
The “HDMI Output Setting” menu appears next.
2
Use the Up and Down [ ]/[ ] buttons to select “On” or “Off” for “HDMI Output Setting”, and then press [Enter].
Select “On” to use the HDMI output.
Initial Setup
TV Shape
HDMI Output Setting
On-Screen Language
: 4:3 Letter box
On
Off
The “On-Screen Language” menu appears next.
3
Use the Up and Down [ ]/[ ] buttons to select a language, and then press [Enter].
See page 61 for more information on the language options.
TV Shape
HDMI Output Setting
On-Screen Language
: 4:3 Letter box
: On
English Français Español Deutsch Italiano
The “Initial Setup” menu closes and the setup is complete. The DVD receiver is now ready to use.
Note:
You can cancel the “Initial Setup” by pressing the [Setup] button and complete the settings later by using the onscreen setup menus (see page 57).
29
HDMI and Progressive Settings
HDMI
Resolution
Note:
Stop playback before perform these settings.
Setting the HDMI
This section explains how to turn on the HDMI OUT and change the video resolution when your TV or projector is connected to the HDMI OUT.
1
DVD r ece ive r
2
Remote controller
The DVD receiver supports the following resolutions:
AUTO:
The resolution is automatically set to the native resolu­tion of the TV connected to the HDMI OUT.
If the DVD receiver does not support the TV’s native res­olution setting, the resolution 480p will be used.
480p (default):
The setting displayed depends on the country in which you purchased the DVD receiver.
u 480p 60Hz
720 Also output by the DVD receiver’s analog video outputs. With this setting, component video output will be pro-
gressive.
720p:
1280
u 720p 50/60Hz
Not output by the DVD receiver’s analog video outputs.
1080i:
1920
u 1080i 50/60Hz
Not output by the DVD receiver’s analog video outputs.
Press the DVD receiver’s [HDMI] button to turn on HDMI.
Press the [Resolution] button repeatedly to change the HDMI resolution.
The first button press displays the cur­rent resolution onscreen. Press the but­ton again while the resolution is displayed to change the setting.
Tip:
These settings can also be changed by using the onscreen setup menus (see pages 59, 60).
Note:
Be sure to choose a resolution that’s supported by your TV. If you select a resolution that your TV doesn’t sup­port, there will be no picture.
Selecting Progressive or Interlaced
If your TV supports progressive video, you can set the DVD receiver to progressive and enjoy progressive video on your TV. If your TV doesn’t support progres­sive video, set the DVD receiver to interlaced.
When HDMI output is at 480p, the component video output is fixed at progressive and depending on the selected resolution there may be no output, so turn off the HDMI OUT before changing this setting.
1
DVD re ceiv er
2
Remote controller
Press the DVD receiver’s [HDMI] button to turn off HDMI.
Use the [Resolution] button to select “Progressive” or “Inter­lace”.
The first button press displays the cur­rent setting onscreen. Press the button again while the setting is displayed to change the setting. The PRGSV indicator appears on the display when progressive is selected.
30
Understanding Common Operations
Input selector Master Volume control
Phones
Adjusting the Volume
DVD re ceiv er
Use the Master Volume control, or the remote control­ler’s VOL [ ]/[ ] button. The volume can be set to “Min”, “1” through “79”, “Max”. Depending on subwoofer level or listening mode, the maximum volume varies.
Remote
controller
or
Selecting the Input Source
DVD receiver
or
You can select DVD, FM, AM, or connected other AV component (set top box, Onkyo RI Dock) as the input source. Use the DVD receiver’s Input selector to select the input source. To select the input source with the remote controller, press the Input [ ] or [ ] button repeatedly.
Remote
controller
Sleep
Input
Muting
/
VOL
When reproducing the audio and video signals from HDMI IN, select “VIDEO 1”.
Using Headphones
You can connect a pair of stereo headphones (1/4-inch phone plug) to the DVD receiver’s Phones jack for pri­vate listening, as shown.
Notes:
• Always turn down the volume before connecting your headphones.
• The speakers are turned off while the headphones plug is inserted in the Phones jack.
• When you connect a pair of headphones, the listening mode is set to “Stereo”, unless it’s already set to “Ste­reo” or “Direct”.
• Only the Stereo and Direct listening modes can be used with headphones (the listening modes available also depend on the currently selected input source).
DVD VIDEO 1 VIDEO 2/DOCK
FMAM
31
Understanding Common Operations—Continued
Muting the DVD receiver
You can temporarily mute the output of the DVD receiver.
Remote controller
Press the [Muting] button.
The output is muted and the MUTING indicator flashes on the display, as shown.
MUTING
To unmute the DVD receiver, press the [Muting] button again, or adjust the volume.
The Mute function is cancelled when the DVD receiver is set to Standby.
Using the Sleep Timer
With the sleep timer, you can set the DVD receiver to turn off automatically after a specified period.
Remote controller
Press the [Sleep] button repeat­edly to select the required sleep time.
The sleep time can be set from 90 to 10 minutes in 10 minute steps.
The SLEEP indicator appears on the display when the sleep timer has been set. The specified sleep time appears on the display for about five seconds, then the previous display reappears.
Adjusting Subwoofer Level
You can adjust the level of Subwoofer during play-
back.
Remote controller
Press the [Subwoofer Level] but­ton, and then use the Left and Right [ ]/[ ] buttons to adjust the volume.
You can adjust the volume of Sub­woofer from –15 dB to +12 dB in 1 dB steps.
When you’ve finished, press the [Sub­woofer Level] button again.
If you need to cancel the sleep timer, press the [Sleep] button repeatedly until the SLEEP indicator disappears.
To check the time remaining until the DVD receiver sleeps, press the [Sleep] button. Note that if you press the [Sleep] button while the sleep time is being displayed, you’ll shorten the sleep time by 10 minutes.
32
Playing Discs
This chapter covers basic playback. Advanced playback functions are covered in the “Advanced Playback” on page 43.
Stop
Open/Close Play
Pause
1
DVD receiver
Press [Open/Close] to open the disc tray.
The input source is automatically set to DVD.
Starting, Pausing & Stopping Playback
This section explains how to start, pause, and stop play­back.
Start
DVD r ece ive r
Remote controller
Pause
DVD r ece ive r
Remote controller
To start playback, press the Play [] button.
Playback starts and the Play indica- tor appears on the display.
If you’re playing a DVD-Video disc, or a VCD with PBC (Playback Control), you may need to start playback from a menu (see page 36).
• For details on playing MP3, WMA, or JPEG picture discs, see pages 37 and 38.
To pause playback, press the Pause [ ] button.
Playback pauses and the Pause indi- cator appears on the display. To restart playback, press the Play [ ] button. Playback restarts and the Pause
indicator disappears. For DVD-Audio discs, pause cannot be used while a menu is displayed.
2
3
Note:
Only load discs that are supported by the DVD receiver. See pages 8 to 9.
Load a disc.
Load a disc with the label side facing up, using the disc tray guide to align the disc (if you’re loading a double-sided DVD disc, load it with the side you want to play face down).
Press [Open/Close].
The disc tray closes and the relevant disc type indicator appears on the display.
Tip:
If you press the Play [ ] button, the disc tray will close and, depending on the type of disc, playback will start automat­ically.
33
Playing Discs—Continued
Stop
DVD r ece ive r
To stop playback, press the Stop [] button.
Playback stops and the Play indica- tor disappears.
• When you stop playback of a
Remote controller
DVD-Video disc, the DVD receiver remembers the point at which play­back was stopped and “Resume” appears onscreen. To resume play­back from that point, press the Play [ ] button. To cancel the “Resume” function, press the Stop [ ] button again. The Resume function is reset when the disc is removed from the DVD receiver.
• With the Last Memory function you can resume playback from any point even if the disc has been removed (see page 48).
Notes:
• Prolonged display of the same picture or menu may cause irreparable damage to your TV screen known as screen burn-in. To prevent this, don’t keep playback paused for too long and always press the Stop [ ] but­ton when you’ve finished playing a DVD disc or VCD. The DVD receiver features a screen saver to protect your TV from the effects of burn-in (see page 63).
• With some DVD-Video discs, you may experience picture noise that is not normally visible with standard TV broadcasts. This is usually because DVD-Video uses a lot of high-resolution video data. The amount of noise, if any, will depend on your particular TV and the problem can sometimes be alleviated by turning down the TV’s sharpness control.
Select Next & Previous track/chapter
DVD-V
DVD-A
SACD
This section explains how to skip to the next and previ­ous track and chapter.
Select Next track/ chapter
DVD re ceiv er
Remote controller
Select Previous track/ chapter
DVD re ceiv er
Remote controller
During Playback, press the Next [ ] button to select next track/ chapter.
The Next track/chapter starts playback.
During Playback, press the Previ­ous [ ] button to select previ­ous track/chapter.
The first press selects the beginning of the current track.
VCD
CD
MP3
WMA
JPEG
34
Playing Discs—Continued
Forward Frame-by-Frame Playback
DVD-V
VCD
With frame-by-frame playback you can view individual picture frames one at a time forward.
Fast Forward & Reverse
DVD-V
DVD-A
SACD
VCD
This section explains how to fast forward and reverse.
Fast forward
During playback, press the [ ] button to start fast forward.
Playback fast forwards and “ x2” appears onscreen.
To change the fast-forward speed, press the [ ] button repeatedly to select: x2, x4, x8, x16.
To resume normal playback, press the Play [ ] button.
CD
MP3
Forward frame-by­frame
Press the Pause [ ] button. Press it repeatedly to view sub­sequent frames.
To resume normal playback, press the Play [ ] button.
Fast reverse
During playback, press the [ ] button to start fast reverse.
Playback reverses and “ x2” appears onscreen.
To change the fast-reverse speed, press the [ ] button repeatedly to select: x2, x4, x8, x16.
To resume normal playback, press the Play [ ] button.
Notes:
• Fast forward and fast reverse may not always work at the speed shown onscreen.
• For discs other than audio CDs, no sound is output during fast forward or fast reverse.
• For DVD-Audio discs, fast forward and fast reverse cannot be used while a menu is displayed.
35
Playing Discs—Continued
Number
buttons
Top Menu
Enter
Menu
• On some DVDs, to display the disc menu, press the [Menu] button.
• Since the multichannel input source of DVD-Audio is down mixed, the output will be a processed audio. To output an original audio, select the 2-channel source. Some DVD-Audio discs may not be down mixed; in this case select the 2-channel source.
To set VCD’s PBC on and off
PBC menus can turned on or off by pressing the [Top Menu] button.
Navigating CDs & Super Audio CDs
SACD
CD
This section explains how to play audio CDs and Super Audio CDs with the “Disc Navigator”.
Navigating DVD & VCD Disc Menus
DVD-V
DVD-A
VCD
DVD-Video discs usually have a menu from which you can select titles, chapters, and other options, including soundtracks, subtitles, and audio formats (e.g., Dolby Digital or DTS). VCDs that support PBC (Playback Control) may also have an onscreen menu.
1
2
Load a DVD or VCD.
With DVDs, a menu usually appears when the Play [ ] button is pressed. If it doesn’t, try pressing the [Top Menu] button. With VCDs that support PBC, you may have to press the Play [ ] button to dis­play the menu.
On a DVD menu, use the arrow [], [], [], [] buttons to select an item, and then press [Enter].
1
2
Load an audio CD or Super Audio CD.
The “Disc Navigator” appears.
-/13
001. Track01
002. Track02
003. Track03
004. Track04
005. Track05
006. Track06
007. Track07
008. Track08
Disc CD
Repeat :Off Random :Off
CDDA
/Track01.CDA
The tracks are displayed.
Use the Up and Down [ ]/[ ] buttons to select a track, and press [Enter] to start playback.
With SACDs, you can select the multi­channel area, 2-channel area, or CD layer by pressing the [Audio] button.
Since the multichannel area is down mixed, the output will be a processed audio. To output an original audio, select the 2-channel area.
On a VCD menu, use the number buttons to select the tracks.
If the VCD’s menu consists of several pages, use the Next [ ] and Previous [ ] buttons to view them. During playback, you can return to the menu by pressing the [Return] button.
Notes:
• Not all DVDs and VCDs have menus.
• Menu operation varies from disc-to-disc. See the disc’s sleeve notes for details.
36
Note:
During random playback or memory playback, the arrow buttons cannot be used.
Playing Discs—Continued
Enter
/ / /
Return
Navigating MP3 & WMA Discs
MP3
WMA
This section explains how to play MP3 and WMA files with the “Disc Navigator”.
1
2
Load an MP3 or WMA disc.
The “Disc Navigator” appears.
-/51/3
001. ROOT
002. mp3
003. MP3 music
001. Track01
002. Track02
003. Track03
004. Track04
005. Track05
Disc – – – –
Repeat :Off Random :Off
DATA
/mp3
Initially, the folders in the root direc­tory are displayed.
The DVD receiver numbers folders and tracks in hierarchical order. You can use these numbers to select folders and tracks directly with the Search function (see page 43).
To open a folder, use the Up and Down [ ]/[ ] buttons to select it, and then press [Enter].
The contents of the folder are dis­played.
3
Use the Up and Down [ ]/[ ] buttons to select tracks and sub­folders in the open folder.
To open a folder in the list, press the [Enter] button. To close a folder (i.e., move back up the directory tree), press the [Return] button. Alternatively, select the item at the top of the list and press the [Enter] button.
Use the Left and Right [ ]/[ ] buttons to display the other folders that contain playable tracks.
4
To play the selected track, press the Play [ ] or [Enter] button.
If available, the ID3 tag information, (Title name, Artist name, Album name,
or
and so on) will scroll across the bottom of the screen.
Play
Disc DATA
3/11
2/3
/mp3/03 Track03.MP3
002. mp3
001. Track01
002. Track02
003. Track03
004. Track04
005. Track05
006. Track06
007. Track07
Name: Onkyo Artist Name: Onkyo Album Name: Onkyo
For MP3 playback
00:00:29 00:03:58 00:04:27
Repeat :Off Random :Off
Subsequent tracks in the same folder are played in order.
5
Press the Stop [ ] button to stop playback.
Note:
During random playback or memory playback, the arrow buttons cannot be used.
37
Playing Discs—Continued
Viewing a Slideshow of JPEG Images
JPEG
This section explains how to display a slideshow of JPEG images on your TV.
1
2
Remote controller
Load a JPEG disc.
The “Disc Navigator” appears.
DATA
/jpg
001. jpg
002. image0
003. image1
004. image2
005. image3
001. 001
002. 002
003. 003
Disc – – – –
-/-1/17
Repeat :Off Random :Off
Initially, the folders in the root direc­tory are displayed.
The DVD receiver numbers folders and files in hierarchical order. You can use these numbers to select folders and files directly with the Search function (see page 43).
To open a folder, use the Up and Down [ ]/[ ] buttons to select it, and then press [Enter].
The contents of the folder are dis­played.
4
To open a folder in the list, press the [Enter] button. To close a folder (i.e., move back up the directory tree), press the [Return] button. Alternatively, select the item at the top of the list and press the [Enter] button.
Use the Left and Right [ ]/[ ] buttons to display other folders that contain JPEG images.
To play a slideshow, press the Play [ ] or [Enter] button.
Subsequent images are displayed in order, with each image being displayed
or
for five seconds. To display an image for longer, press
the Pause [ ] button. Press the Play [ ] button to resume.
Use the Previous and Next [ ]/[ ] buttons to view the previous or next image. To flip a picture 180 degrees, use the Up and Down [ ]/[ ] buttons (not while zoomed in). To rotate a picture counterclockwise or clockwise, use the Left and Right [ ]/ [ ] buttons (not while zoomed in). To zoom in or out, use the [ ] and [ ] buttons. While zoomed in, use the [ ]/[ ]/[ ]/[ ] buttons to move around the picture.
38
3
Use the Up and Down [ ]/[ ] buttons to select images and subfolders in the open folder.
A thumbnail-size preview for the cur­rently selected image is displayed.
DATA
/image1/001.JPG
-/-1/17
005. image1
001. 001
002. 002
003. 003
004. 004
005. 005
006. 006
007. 007
Disc
– – – –
Repeat :Off Random :Off
W: 150 H: 120
5
To stop the slideshow, press the Stop [ ] or [Menu] button.
The slideshow stops automatically when all pictures have been displayed.
or
To display thumbnails
To display thumbnails, in step 3, after opening the folder you want to display, press the [Top Menu] button.
Use the arrow [ ], [ ], [ ], [ ] buttons to select the thumbnails, and press [Enter] to start a slideshow. Press the [Menu] button to return to the “Disc Navigator”. Use the Previous and Next [ ]/[ ] buttons to dis­play other pages.
About HD JPEG
If your TV is connected via HDMI and the HDMI reso­lution is set to 720p or 1080i, you can view your JPEG images in high definition (see page 60).
Listening to the Radio
Tuning into Radio Stations
Input
Number
buttons
Tuning
Search
Memory
CLR
Preset
Mode
Using the Tuner
With the built-in tuner you can enjoy AM and FM radio stations. You can store your favorite stations as presets for quick selection.
Listening to the Radio
Use the Input [ ]/[ ] button to select either AM or FM.
In this example, FM has been selected.
Auto Tuning Mode
1
2
When tuned into a station, the indicator appears. When tuned into a stereo FM station, the FM ST indica­tor appears on the display, as shown.
Note:
This procedure can also be performed on the DVD receiver by using its Tuning/Preset [ ]/[ ] button. Press the Tuning/Preset [ ]/[ ] button to start searching for a few seconds. Pressing the Tuning/Preset [ ]/[ ] button again stops the searching. After this, press the button repeatedly to change the fre­quency one step at a time.
Manual Tuning Mode
1
Press the [Mode] button so that the AUTO indicator appears on the display.
Press the Tuning [ ]/[ ] button.
Searching stops when a station is found.
To stop searching, press Stop [ ] but­ton.
AUTO FM ST
FM STAUTO
Press the [Mode] button so that the AUTO indicator disappears from the display.
Band Frequency
(Actual display depends on country)
2
HOLD
Radio Frequency can be changed in 0.2 MHz steps for FM and 10 kHz steps for AM.
In Manual Tuning mode, FM stations will be in mono.
Tuning into weak FM stereo stations
If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to Manual Tuning mode and listen to the station in mono.
Press and hold the Tuning [ ]/ [] button.
The frequency stops changing when you release the button. Press the buttons repeatedly to change the frequency one step at a time.
39
Listening to the Radio—Continued
Tuning into Stations by Frequency
You can tune into AM and FM stations directly by enter­ing the appropriate frequency.
1
2
Press the [Search] button.
Within 8 seconds, use the num­ber buttons to enter the fre­quency of the radio station.
For example, to tune to 87.5 (FM), press 8, 7, 5.
Presetting AM/FM Stations
You can store a combination of up to 40 of your favorite AM/FM radio stations as presets.
1
2
Tune into the AM/FM station that you want to store as a preset.
Press the [Memory] button.
The preset number flashes.
Selecting Presets
To select a preset, use the Preset [ ]/[ ] buttons.
Notes:
• This procedure can also be performed by using the number buttons. To enter, for example, “12”, press the [1] button fol­lowed by the [2] button.
• This procedure can also be performed on the DVD receiver by using its Tuning/Preset [ ]/[ ] button.
Deleting Presets
1
2
Select the preset that you want to delete.
See the previous section.
Press the [CLR] button twice.
The preset is deleted and its number disappears from the display.
3
4
Note:
This procedure can also be performed on the DVD receiver by using its [Preset Memory] button and Tun­ing/Preset [ ]/[ ] button. First press the [Preset Mem­ory] button, use Tuning/Preset [ ]/[ ] button to select a preset and then press the [Preset Memory] button again.
While the preset number is flash­ing (about 8 seconds), use the Preset [ ]/[ ] buttons to select a preset from 1 through 40.
Press the [Memory] button again to store the station or channel.
The station or channel is stored and the preset number stops flashing.
Repeat this procedure for all of your favorite AM/FM radio stations.
40
Using the Listening Modes
Selecting Listening Modes
See “About the Listening Modes” in the right column for detailed information about the listening modes.
Listening Mode
About the Listening Modes
Direct
In this mode, audio from the input source is output directly with minimal processing, providing high-fidel­ity reproduction.
Stereo
The selected input source is processed as a stereo signal and output by the front left and right speakers and the subwoofer if connected.
T-D (Theater-Dimensional)
With this mode you can enjoy a virtual 5.1 surround sound even with only two speakers. This works by con­trolling how sounds reach the listener’s left and right ears. Good results may not be possible if there’s too much reverb, so we recommend that you use this mode in an environment with little or no natural reverb.
Notes:
• T-D listening mode cannot be selected while head­phones are connected to the DVD receiver.
• During playback a DVD-Audio or SACD, T-D listen­ing mode cannot be selected.
Press the [Listening Mode] but­ton to select a listening mode.
Pressing this button repeatedly cycles through all of the listening modes that can be used with the current input source.
41
Using the Listening Modes—Continued
T-D (Theater-Dimensional) Listening Angle Setting
With this setting, you can specify the angle of the front left and right speakers relative to the listening position.
Processing for the Theater-Dimensional listening mode is based on this setting. Ideally, the front left and right speakers should be equidistant from the listening posi­tion and at an angle close to one of the three available settings.
Front left speaker Front right speaker
20/30/40°
2
Use the Up and Down [ ]/[ ] buttons to select “Angle”, and use the Left and Right [ ]/ [ ] buttons to select: “Narrow”, “Middle”, or “Wide”.
Narrow: Select if the listening angle
is 20 degrees.
Middle: Select if the listening angle
is 30 degrees (default).
Wide: Select if the listening angle
is 40 degrees.
When you’ve finished, press the [Setup] button again.
The setup menu closes.
1
Remote controller
HOLD
Press and hold the [Setup] but­ton for 3 seconds.
When selecting the input other than DVD, just press the [Setup] button. “Balance” appears on the display.
3
Note:
Only when the T-D listening mode is selected, this set­ting is available.
Listening Mode and Receiver Settings
Depending on the listening mode, the setup menu settings may be enabled/disabled as shown below.
Listening Mode
Settings Page # Direct Stereo T-D
Speaker Output Balance 55
Subwoofer Level 32
Correcting Sound and Picture
Sync
Crossover Frequency 56
Enabling/Disabling the Subwoofer 55
Front Speakers Size 55
*1 During playback a DVD-Audio or SACD, this setting is fixed at 100 Hz. *2 During playback a DVD-Audio or SACD, this setting is fixed at Small.
55
✔✔
✔✔
✔✔
*1
✔✔
*2
: available
42
Advanced Playback
Number
buttons
Enter
Search
Selecting Chapters/Titles/Tracks/ Folders by Number
DVD-V
DVD-A
SACD
VCD
With the “Search” function you can select chapters, titles, and tracks by number. To use the function with DVD, DVD playback is required.
CD
MP3
WMA
2
3
or
Use the number buttons to spec­ify a title, chapter, or track num­ber.
To enter, for example, “12”, press the [1] button followed by the [2] button.
Search
Disc
DVD-VIDEO
Current/Total
Entered title number appears here
Title
12/ 19
Entered chapter number appears here
Chapter
Current/Total
5/ 7
If you’re playing a DVD, MP3, or WMA disc, use the Left and Right [ ]/ [ ] buttons to select the Title/Group/ Folder and Chapter/Track fields. To clear a number, press the [CLR] but­ton.
Press the Play [ ] or [Enter] but­ton to start playback of the spec­ified title, chapter, or track.
1
Press the [Search] button.
The “Search” window appears onscreen.
This is what appears for DVDs.
Search
Disc
DVD-VIDEO
Title
Current/Total
1/ 19
Chapter
Current/Total
This is what appears for CDs.
Search
Disc
CDDA
Track
Current/Total
- -/ 10
- - -/ 78
Notes:
• During playback, you can select other chapters or tracks directly by using the number buttons (i.e., with­out pressing the [Search] button). For example, to select chapter #2, simply press [2]. To select chapter #10, press [+10] and [0].
• DVD-Video discs usually have menus for selecting titles and chapters.
• When Video CD PBC is on, you can’t search for tracks. Turn PBC off first.
• The [Search] button cannot be used during random playback or memory playback.
• Search may not work with some discs.
43
Advanced Playback—Continued
Number
buttons
Enter
Searching by Time
DVD-V
DVD-A
With the “Search” function you can search by time.
SACD
VCD
CD
Search
Notes:
• In some cases, playback may start from a slightly dif­ferent point to the one that you specify.
• Time search may not work with some discs.
• Time search cannot be used while a DVD-Video or Video CD menu is displayed onscreen.
• The [Search] button cannot be used during random playback or memory playback.
1
2
3
or
During playback, press the [Search] button twice.
The “Search” window appears onscreen.
Search
Disc
DVD-VIDEO
Time
-:- -:- -
Use the number buttons to enter a time.
Time search only works within the cur­rent title or track.
To enter, for example, 5 minutes, 30 seconds, press [5] [3] [0] buttons.
Search
Disc
DVD-VIDEO
Time
-:-5:30
To clear a number, press the [CLR] but­ton.
Press the Play [ ] or [Enter] but­ton to start playback of the spec­ified time.
44
Advanced Playback—Continued
A-B Repeat Playback
DVD-V
SACD
VCD
With the “Repeat A-B” function you can play a specified section over-and-over again.
CD
MP3
Repeat
A–B
Repeat Playback
DVD-V
DVD-A
With the “Repeat” function you can play a disc, title, chapter, group, track, or folder over-and-over again.
1
SACD
VCD
During playback, press the [Repeat] button repeatedly to select a repeat option.
The selected repeat option appears onscreen. The available options depend on the type of disc, as follows: DVD-Video: Chapter Repeat, Title Repeat, Disc Repeat, Repeat Off. DVD-Audio: Track Repeat, Group Repeat, Repeat Off. SACD, VCD, CD: Track Repeat, Disc Repeat, Repeat Off. MP3, JPEG, WMA: Track Repeat, Folder Repeat, Disc Repeat, Repeat Off.
CD
MP3
WMA
JPEG
1
2
3
Notes:
• The “Repeat A-B” function may not work with some DVD-Video discs and VCDs that support PBC.
• In some cases, the A and B points may be at slightly different points to the ones that you specify.
During playback, press the [A-B] button to set the A point (i.e., the start of the section you want to repeat).
“Repeat A-” appears onscreen and “-R_A” appears on the display.
Press the [A-B] button again to set the B point (i.e., the end of the section you want to repeat).
Playback repeats between the A and B points, and “Repeat A-B” appears onscreen and “-R_AB” appears on the display.
To cancel A-B repeat playback, press the [A-B] button.
2
Notes:
• Repeat playback may not work with some discs.
• If the “Memory Playback” function is on (see page 47), the selectable options are “Memory Repeat”, which plays the playlist repeatedly, and “Repeat Off”.
• To use the Repeat function with a VCD that supports PBC, you must first turn off PBC (see page 36).
To cancel repeat playback, use the [Repeat] button to select “Repeat Off”.
45
Advanced Playback—Continued
Random
Random Playback
DVD-V
With the “Random” function you can enjoy a random selection of titles, chapters, groups, tracks, or folders.
DVD-A
SACD
VCD
CD
MP3
WMA
• To use the “Random” function with a VCD that sup­ports PBC, you must first turn off PBC (see page 36).
• If the “Memory Playback” function is on (page 47), random playback is unavailable.
• You can’t use the [Search] button during random play­back.
• During random playback, the remote controller’s arrow [ ], [ ], [ ], [ ] buttons and number buttons don’t work with the “Disc Navigator”.
• The “Random” function cannot be used with JPEG files.
1
During playback, press the [Ran­dom] button repeatedly to select a random option.
The selected random option appears onscreen. The options available depends on the type of disc, as follows: DVD-Video: Title Random, Disc Ran­dom, Random Off. DVD-Audio: Group Random, Random Off. SACD, VCD, CD: Disc Random, Ran­dom Off. MP3, WMA: Folder Random, Disc Random, Random Off. With the “Title Random” option, chap­ters within the current title are played at random. With the “Disc Random” option, titles, chapters, groups, tracks, or folders on the disc are played at ran­dom.
Random playback begins after the cur­rent chapter or track has finished.
Random playback stops automatically when all of the items have been played once.
2
Notes:
• Random playback may not work with some discs.
To cancel random playback, use the [Random] button to select “Random Off”.
46
Advanced Playback—Continued
Number
buttons
Enter
Memory Last
Memory CLR
Memory Playback
DVD-A
DVD-V
With the “Memory Playback” function you can create your own memory list of titles, chapters, and tracks.
1
2
SACD
VCD
CD
MP3
WMA
Press the [Memory] button.
The “Memory List” window appears onscreen, as shown.
Memory List
Title/Folder Chapter/TrackNo.
Current/Total 001 / 019 Current/Total --- / 078
--- / 01901 --- / 078
--- / 01902 --- / 078
--- / 01903 --- / 078
--- / 01904 --- / 078
--- / 01905 --- / 078
--- / 01906 --- / 078
--- / 01907 --- / 078
--- / 01908 --- / 078
The top row ( ) is used to enter title/ folder and chapter/track numbers.
The steps in the memory list are num­bered.
Enter the title/folder (group), and chapter/track numbers of the item you want to add to the mem­ory list, and then press [Enter].
Use the remote controller’s Left/Right [ ]/[ ] buttons to select the parame­ters, and use the number buttons to enter the number.
The new item is added to the memory list as step 01.
3
Repeat step 2 to add more items to the memory list.
You can add up to 32 items to the mem­ory list.
4
To play the memory list, press the Play [ ] button.
The “Memory List” window must be open when you press the Play [ ] but­ton.
5
To stop playback, press the Stop [] button.
While playback is stopped, you can delete the memory list by pressing the [CLR] button.
While playback is stopped, you can cancel the Memory Playback function by pressing the Stop [ ] button again.
Adding New Items to the List
1
2
3
Use the Up/Down [ ]/[ ] but­tons to select the step which you want to insert the new item, and then press the [Enter] button.
Memory List
Title/Folder Chapter/TrackNo.
Current/Total 001 / 019 Current/Total --- / 078
005 / 01901 001 / 078 002 / 01902 012 / 078
--- / 01903 --- / 078 003 / 01904 004 / 078 010 / 01905 003 / 078
--- / 01906 --- / 078
--- / 01907 --- / 078
--- / 01908 --- / 078
Enter the title/folder (group), and chapter/track numbers of the item to be inserted.
Use the remote controller’s Left/Right [ ]/[ ] buttons to select the parame­ters, and use the number buttons to enter the number.
Press the [Enter] button.
The new item is inserted into the mem­ory list and subsequent items move down the list.
47
Advanced Playback—Continued
Deleting Items from the List
Use the Up/Down [ ]/[ ] but­tons to select it, and then press the [CLR] button.
The item is deleted and subsequent items move up the list.
Editing Steps
1
2
Use the Up/Down [ ]/[ ] but­tons to select the step.
Use the Left/Right [ ]/[ ] but­tons and number buttons to edit the title/folder (group) or chapter/ track numbers, and then press [Enter].
Last Memory
DVD-V
With the “Last Memory” function you can resume play­back from where you left off even if the disc has been removed and the DVD receiver has been set to Standby. “Last Memory” also remembers the soundtrack and sub­title settings you were using.
1
2
3
During DVD playback, press the [Last Memory] button.
The last memory point for the disc is stored, “Last play.
If the [Last Memory] button is pressed again, the last memory point is updated.
To stop playback, press the Stop [ ] button.
Now you may remove the disc and turn off the DVD receiver.
To resume playback, load the disc, and then press the Play [ ] button.
The “Last Memory” dialog box appears.
Last Memory is set. Start playback from memory location?
Mem” appears on the dis-
Yes No Memory Clear
Notes:
• To close the “Memory List” window, press the [Return] button.
• The memory list will be deleted when the DVD receiver is set to Standby or the disc tray is opened.
• To use this function with a VCD that supports PBC, you must first turn off PBC.
• The Memory Playback function cannot be used with some discs.
• JPEG images can be added to the memory list, how­ever, they will not be displayed.
48
4
Notes:
• The “Last Memory” function can store the last point for up to six DVDs. When you set the “Last Memory” function for a seventh disc, the first disc’s settings are deleted.
• The “Last Memory” function will not work while a menu is being displayed onscreen.
• The “Last Memory” function may not work with some DVDs.
To resume playback from the last memory point, select “Yes”, and then press [Enter].
To start playback from the present point, select “No”, and then press [Enter].
To delete the last memory point, select “Memory Clear”, and then press [Enter].
Advanced Playback—Continued
/ / /
Selecting Camera Angles
DVD-V
Some DVDs feature multiple camera angles that allow you to view scenes from different angles. When a DVD features multiple camera angles, the camera indicator appears on the display. Such discs usually have the cam­era angle logo ( ) printed on the sleeve.
Angle
Zoom
Zooming
DVD-V
VCD
JPEG
With the Zoom function you can enlarge any part of the picture.
1
HOLD
2
During playback or while play­back is paused, press and hold the [Zoom] button for 3 seconds.
“Zoom x1.0” appears onscreen.
Press the [Zoom] again repeat­edly to Zoom in.
The number of zoom steps available depends on the resolution of the disc or file.
After the maximum zoom, the picture returns to its normal size.
Press the [Angle] button repeat­edly to cycle through the avail­able camera angles.
The number of the currently selected camera angle appears onscreen. For example, on a disc with three camera angles, you’d see 1/3, 2/3, and 3/3.
Notes:
• With some DVDs you may not be able to select differ­ent camera angles even though the camera indica­tor is displayed.
• With some DVDs you can select camera angles from a menu.
3
Notes:
• The Zoom function may not work with some discs.
• The Zoom function cannot be used with HD JPEG.
• The Zoom function cannot be used with disc menus.
To see other areas of the picture while zoomed, use the remote controller’s arrow [ ], [ ], [ ], [ ] buttons.
49
Advanced Playback—Continued
Selecting Subtitles
DVD-V
Some DVD-Video discs feature subtitles in several lan­guages. See the disc’s sleeve notes for details.
Audio
Subtitle
Selecting Soundtracks
DVD-V
DVD-A
SACD
Some DVD-Video discs feature soundtracks in several languages or audio formats (e.g., Dolby Digital or DTS). Music DVD-Video discs and DVD-Audio discs some­times feature audio in several formats, such as PCM, Dolby Digital, or DTS. See the disc’s sleeve notes for details.
During playback, press the [Audio] button repeatedly to cycle through the available soundtracks.
The name of the selected soundtrack appears onscreen for several seconds.
For SACDs, you can select the multi­channel area, 2-channel area, or CD layer. If you make a selection during playback, playback will stop.
During playback, press the [Sub­title] button repeatedly to cycle through the available subtitles.
The name of the selected subtitle appears onscreen for several seconds.
To turn off subtitles, use the [Subtitle] button to select “Off”.
Notes:
• When you stop playback and cancel the “Resume” function (see page 34), the subtitle language will revert to your default subtitle language (see page 61), or the disc’s default subtitle language.
• With some DVDs you can select subtitles from a menu, and you may not be able to select subtitles dur­ing playback.
Notes:
• With DVD-Video discs, when you stop playback and cancel the “Resume” function (see page 34), the soundtrack language will revert to your default lan­guage (see page 61), or the disc’s default language.
• With some discs, selecting another soundtrack may cause the picture to skip momentarily.
• With some DVDs you need to select soundtracks from a menu, and you may not be able to select other soundtracks during playback.
• Since the multichannel input source of SACD and DVD-Audio is down mixed, the output will be a pro­cessed audio. To output an original audio, select the 2­channel source. Some DVD-Audio discs may not be down mixed; in this case select the 2-channel source.
50
Disc and Input Information
Displaying Information
You can display various information about the current disc, or input source as follows.
Remote controller
Disc Information
The information displayed depends on the type of disc, as follows:
DVD-Video
Onscreen:
• Current/total title number, elapsed title time, remain­ing title time, total title time, selected soundtrack, selected subtitle, and the number of available camera angles.
• Current/total chapter number, elapsed chapter time, remaining chapter time, and total chapter time.
Display:
• Elapsed chapter time
• Remaining title time
DVD-Audio
Onscreen:
• Current/total track number, elapsed track time, remaining track time, total track time, and selected soundtrack.
• Current/total group number, elapsed group time, remaining group time, and total group time.
Display:
• Elapsed track time
• Remaining track time
• Elapsed disc time
Press the [Display] button repeatedly to cycle though the available information.
During playback of a disc, various information appears onscreen. The operating status (e.g., Stop, Play, Resume) and disc type information is displayed along the top of the screen.
Audio CD, Super Audio CD
Onscreen:
• Current/total track number, elapsed track time, remaining track time, and total track time.
• Current/total track number, elapsed disc time, remain­ing disc time, and total disc time.
Display:
• Elapsed track time
• Remaining track time
• Elapsed disc time
• Remaining disc time
MP3, WMA
Onscreen:
• Current/total folder number, current/total track num­ber in the folder, elapsed track time, remaining track time (MP3 only), and total track time (MP3 only).
Display:
• Elapsed track time
•File name
• Folder name
• Total number of folders
JPEG
Display:
• Folder number, track number
•File name
• Folder name
• Total number of folders
Input Information
The information displayed depends on the type of input source, as follows:
Display:
• Input source
• Signal format*
• Listening mode
* If the input signal is analog, no format information is displayed.
Video CD
Onscreen:
• Current/total track number, elapsed track time, remaining track time, and total track time.
• Current/total track number, elapsed track time, remaining disc time, and total disc time.
Display:
• Elapsed track time
• Remaining track time
• Elapsed disc time
• Remaining disc time
Note:
If PBC is on, no information is displayed when the [Dis­play] button is pressed.
51
Controlling Other Components
Controlling a TV connected to the DVD receiver
You can control a TV. You must enter the appropriate remote control code first.
Number
buttons
TV
Enter
Entering Remote Control Codes
4
Note:
The remote control codes provided are correct at the time of printing, but are subject to change.
Controlling a TV
To control a TV, point the remote controller at it and use the buttons explained below. With some TVs, certain buttons may not work as expected, and some may not work at all.
Point the remote controller at the TV, and check the operation.
If the remote controller doesn’t work as expected, and several remote codes are listed, try each one in turn and use the one that works best.
 
1
2
3
HOLD
HOLD
Look up the appropriate remote control code in the “Remote Con­trol Codes list” at the end of this manual.
Hold down the TV [ ] and [Enter] buttons for about 3 sec­onds.
Within 30 seconds, use the num­ber buttons to enter the 4-digit remote control code.
TV [ ] button
Sets the TV to Standby or On.
TV [Input] button
Selects the TV’s AV input.
TV VOL [ ]/[ ] button
Adjusts the TV’s volume.
TV [CH +/–] button
Selects channels on the TV.
52
Controlling Other Components—Continued
Controlling an Apple iPod in RI Dock connected to the DVD receiver
When operating an Apple iPod in RI Dock with an connection, you can control it by DVD receiver’s remote controller.
When Using an RI Dock:
• Connect the RI Dock to the VIDEO 2/DOCK INPUT jacks (see page 25).
• Set the RI Dock’s RI MODE switch to HDD or HDD/ DOCK.
• See to the RI Dock’s instruction manual for more information.
Press the Input [ ]/[ ]buttons to select “VIDEO2/ DOCK”.
(2
(3
 
(4
(5 (6 (7
 (1
Standby/On button
Sets the iPod to Standby or On.
Playlist [ ]/[ ] buttons*
Used to select the previous or next playlist on the iPod.
Album [ ]/[ ] buttons*
Selects the next or previous album.
TOP Menu button*
Used to access menus.
Arrow [ ]/[ ] and Enter buttons*
Used to navigate menus and select items.
Pause [ ] button
Pauses playback. (With 3rd generation iPods, it works as a Play/Pause button.)
Rewind [ ] button
Press and hold to rewind.
Fast Forward [ ] button
Press and hold to fast forward.
Random button*
Used with the shuffle function.
(1 Repeat button*
Used with the repeat function.
(2 Menu button
Works as a Mode button when used with a DS-A2/ A2X RI Dock.
(3 Play [ ] button
Starts playback. If the component is off, it will turn on automatically. (With 3rd generation iPods, this button works as a Play/Pause button.)
(4 Stop [ ] button
Stops playback and displays a menu.
(5 Next [ ] button
Selects the next song.
(6 Previous [ ] button
Restarts the current song. Press it twice to select the previous song.
(7 Mode button*
Turns on the backlight for 30 seconds.
* Buttons marked with an asterisk ( ) are not supported
by 3rd generation iPods.
Notes:
Auto Power On Fun cti on If you start iPod playback while the DVD receiver is on Standby, the DVD receiver will automatically turn on and select “VIDEO2/DOCK” input. Then, your iPod will start playback.
Direct Change Function If you start iPod playback while listening to another input source, the DVD receiver will automatically select “VIDEO2/DOCK” input.
• When you don’t listen to the iPod, stop playback. The direct change function activates at the change of tracks to automatically change the input to “VIDEO2/DOCK”.
*
53
Configuring the DVD receiver
Setup Menu
Here you can configure the DVD receiver in this menu on display. The configurations are common for the all input settings excluding “AVSync”, “Video1 Input” and “Video2 Input”.
1
Remote controller
HOLD
For detailed information, refer to the pages in brackets.
Balance: 0
Speakers Output Balance [55]
SW Level: 0
Subwoofer Level [32]
AVSync: 0ms
Correcting Sound and Picture Sync [55]
Press and hold the [Setup] but­ton for 3 seconds.
When selecting the input other than DVD, just press the [Setup] button. “Balance” appears on the display.
2
3
Use the Up and Down [ ]/[ ] buttons to select the menus and use the Left and Right [ ]/[ ] buttons to select settings.
When you’ve finished, press the [Setup] button again.
The setup menu closes. Press the [Return] button to return pre-
vious display.
Operations
54
Angle:Middle
T-D Listening Angle
L Night:Off
Late Night Function [55]
Dimmer : 1
Display Brightness [55]
Advanced
Lock Setup
Lock Setup [55] Front Speakers Size [55]
*1
[42]
Xover :100Hz
Crossover Frequency [56]
Video1 Input
Video2 Input
Subwfr: Yes
Enabling/Disabling the Subwoofer [55]
Front :Small
Input :OPT
Audio Input Setup [56]
Format :Auto
Digital Input Signal Formats [56]
*1 Only when the T-D listening
mode is selected, this setting is available.
Configuring the DVD receiver—Continued
Speakers Output Balance
Here you can adjust the output balance of speakers. The balance can be adjusted from “L + 12” to “R + 12”
in 1 steps.
Note:
When the listening mode is set to “Direct”, no effect will be produced.
Correcting Sound and Picture Sync
When using progressive scanning on your DVD receiver, you may find that the picture and sound are out of sync. With this setting, you can correct this by delaying the audio signals.
• You can set it from 0 to 100 milliseconds (msec) in 20 millisecond steps.
• The setting is available for each input source other than FM and AM.
Note:
When the listening mode is set to “Direct”, no effect will be produced.
Late Night Function (Dolby Digital only)
With the Late Night function, you can reduce the dynamic range of Dolby Digital material so that you can still hear quiet parts even when listening at low volume levels—ideal for watching movies late at night when you don’t want to disturb anyone.
Off: Late Night function off (default).
Low: Small reduction in dynamic range.
High: Big reduction in dynamic range.
Notes:
• Depending on the design of the contents, there are some materials that will show no effect even when the Late Night mode is operating.
• The Late Night function resets to the default when the DVD receiver is set to Standby.
Lock Setup
With this preference, you can protect your settings by locking the setup menus.
When the setup menus are locked, you cannot change any setting.
Locked: Setup menus locked.
Unlocked: Setup menus not locked.
Enabling/Disabling the Subwoofer
This section explains how to specify enabling/disabling the subwoofer.
Ye s: Select if a subwoofer is connected.
No: Select if no subwoofer is connected.
Front Speakers Size
This section explains how to specify front speakers sizes. For speakers with a cone diameter larger than 6-1/2 inches (16 cm), spec­ify Large. For those with a smaller diameter, specify Small”. The cross- over frequency can be changed on page 56.
Small: Select if the front speakers are small.
Large: Select if the front speakers are large.
Notes:
• If the “Enabling/Disabling the Subwoofer” the above is set to “No”, this setting is fixed at “Large”.
• When the listening mode is set to “Direct”, no effect will be produced.
Cone diameter
Display Brightness
You can adjust the brightness of the display.
1: Normal + Input selector and Master Volume
control light on.
2: Normal + Input selector and Master Volume
control light off.
3: Dim + Input selector and Master Volume con-
trol light off.
4: Dimmer + Input selector and Master Volume
control light off.
55
Configuring the DVD receiver—Continued
Crossover Frequency
This setting only applies to the speakers that you speci­fied as “Small” in the “Front Speakers Size” on page 55.
To get the best bass performance from your speaker sys­tem, you need to set the crossover frequency according to the size and frequency response of your speakers.
Use the diameter of the smallest speaker in your system when choosing the crossover frequency.
Speaker cone diameter Crossover frequency
Over 8 in.
(20 cm)
6-1/2 to 8 in.
(16
20 cm)
5-1/4 to 6-1/2 in.
(13
16 cm)
3-1/2 to 5-1/4 in.
(9
13 cm)
Under 3-1/2 in.
(9 cm)
*Choose the setting suitable for the speaker.
Notes:
• For a more accurate setting, look up the frequency response in the manuals supplied with your speakers and set accordingly.
• Choose a higher crossover frequency if you want more sound from your subwoofer.
• When a DVD-Audio or an SACD is played in the Ste­reo listening mode, no effect will be produced.
• When the listening mode is set to Direct, no effect will be produced.
40/50/60 Hz*
80 Hz
100 Hz(default)
120 Hz
150/200 Hz*
Audio Input Setup
If you connect a component to a digital input jack, you must assign that jack to an input. For example, if you connect your DVD recorder to the COAXIAL DIGITAL AUDIO IN jack, you should assign that jack to the “Video 1 input”. By default, the COAXIAL DIGITAL AUDIO IN jack is assigned to the “Video 2 input”, although this can be changed.
Here are the default assignments.
Input Default assignment
VIDEO 1 INPUT OPT
VIDEO 2/DOCK INPUT Coax
OPT: optical digital audio input
Coax: coaxial digital audio input
ANA: analog audio input
Note:
The same audio input cannot be simultaneously assigned to both VIDEO 1 INPUT and VIDEO 2/DOCK INPUT.
Digital Input Signal Formats
The digital input signal formats are available only for the input sources that you have assigned a digital input jack (see above). Normally, the DVD receiver detects the signal format automatically. However, if you experience either of the following issues when playing PCM or DTS material, you can manually set the signal format to PCM or DTS:
• If the beginnings of tracks from a PCM source are cut off, try setting the format to PCM.
• If noise is produced when fast forwarding or reversing a DTS CD, try setting the format to DTS.
DTS or PCM: The DTS or PCM indicator, depending on which format you have set, flashes, and only signals in that format are output. Digital signals in other formats are ignored. Auto (default): The format is detected automatically. If no digital input signal is present, the corresponding ana­log input is used instead.
56
DVD Onscreen Setup Menus
This chapter explains the various functions and settings of the onscreen setup menus. Functions and settings are arranged into six menus: Picture, Audio, Language, Display, Operation Setting, and Initial
Setup. The following table lists all the functions and settings, with a brief description and page number where you can find full
details.
Menu Setting Description Page #
TV Shape Select the aspect ratio that matches your TV. 59
View Mode Stretch the picture to fit your TV screen. 59
HDMI Output Setting Turn HDMI video output on or off. 59
Picture
Audio
Language
Display
Operation Setting
Initial Setup
Progressive Setting
HD Resolution Select the video resolution for the HDMI OUT. 60
HD JPEG Mode
Video Black Level Choose a video black level. 60
Brightness Adjust the picture brightness. 60
Sharpness Adjust the picture sharpness. 60
Digital/HDMI Audio Out
Linear PCM Out
On-Screen Language
Disc Menu Language Select your preferred language for disc menus. 61
Audio Language Select your preferred language for soundtracks. 61
Subtitle Language Select your preferred language for subtitles. 61
On-Screen Display Turn on or off onscreen messages and indicators. 63
On-Screen Display Color
Background
Screen Saver Set the Screen Saver function. 63
Parental Lock Set the Parental Lock function. 64
Security Code Change the security code for use with parental lock. 64
DVD Priority Contents
SACD Priority Contents
TV Shape
On-Screen Language
Set the component video output to progressive or interlaced.
For displaying JPEG images at a high resolution on a HDTV.
Settings for the digital signal output by the HDMI digi­tal audio outputs.
Select whether or not the DVD receiver down samples digital audio.
Select a language for the onscreen setup menus and messages.
Select a color for onscreen setup menus and mes­sages.
Select a background color for when playback is stopped.
Determines what’s played on DVD-Audio discs with DVD-Video contents.
Determines how the SACD multichannel and 2-chan­nel area and the CD area are played.
This menu appears automatically the very first time you turn on your DVD receiver. (These settings are available in other menus.)
60
60
61
61
61
63
63
65
65
29HDMI Output Setting
57
DVD Onscreen Setup Menus—Continued
Using the Onscreen Setup Menus
This section explains how to navigate the onscreen setup menus.
Input
Enter
3
Use the Up/Down [ ]/[ ] but­tons to select the options, and press the [Enter] button to con­firm your selection.
1
Setup
Press the Input [ ]/[ ] buttons to select “DVD”, and then press the [Setup] button.
The onscreen setup menu appears, as shown.
Picture
TV Shape
View Mode
HDMI Output Setting
Progressive Setting
HD Resolution
HD JPEG mode
Video Black Level
Brightness
Sharpness
: 4:3 Letter box
: Normal
: On
: Progressive
: 480p
: Off
: Light
: 4
: 4
4
When you’ve finished, press the [Setup] button again.
The onscreen setup menu closes.
58
2
Use the arrow [ ]/[ ]/[ ]/[ ] buttons to navigate the menus, and press the [Enter] button to see the available options.
DVD Onscreen Setup Menus—Continued
Picture Menu
TV Shape
With this setting you can select a picture format to match the aspect ratio of your TV.
4:3 Letter box (default):
Choose this option if you have a standard TV (4:3 aspect ratio). When you watch widescreen DVD-Video movies, the entire pic­ture will be visible and there will be black bars at the top and bottom of the screen, as shown.
4:3 Pan Scan:
Choose this option if you have a standard TV (4:3 aspect ratio) and want to use the full height of the screen when watching widescreen DVD-Video movies. In order to use the full height of the screen, the pic­ture will be cropped on both sides, as shown. This option won’t work with discs that don’t support pan and scan.
16:9 Widescreen:
Choose this option if you have a widescreen TV (16:9 aspect ratio). Depends on TV, the picture appears stretched when watching programs in 4:3 format.
16:9 Compressed:
Choose this option if you have a widescreen TV (16:9 aspect ratio) and the picture appears stretched when watching pro­grams in 4:3 format. This option will correct the issue.
Notes:
• This setting does not apply to DVD menus.
• When the HDMI OUT signal is at a resolution of 720p or 1080i, programs in 4:3 format will appear stretched, so we recommend that you select the “16:9 Com­pressed” option.
• With some DVD-Video discs this setting may have no effect. See the disc’s sleeve notes to see which picture format is used.
View Mode
With this setting you can adjust the aspect of the picture so that it fits your TV screen. Due to your TV’s aspect ratio setting and the DVD’s aspect ratio, black bars may appear above and below the picture or at the sides and the aspect of the picture may be unsuitable. In this case, use this setting to adjust the aspect of the picture as you like.
Normal (default):
The picture is displayed in its original aspect ratio.
View Mode1:
The picture is stretched horizontally to make it fit the height of the screen.
View Mode2:
The picture is stretched vertically to make it fit the width of the screen.
View Mode3:
The picture is stretched horizontally and vertically.
Tip:
The view mode can also be changed by using the remote controller’s [Aspect] button.
Note:
This setting does not apply to DVD menus.
HDMI Output Setting
With this setting you can turn the HDMI video output on or off. See page 30 for more information.
On (default):
Video is output by the HDMI OUT.
Off:
Video is not output by the HDMI OUT.
Tip:
This setting can also be changed by using the [HDMI] button on the front panel (see page 30).
Note:
When this setting is set to “On”, video is output by the analog video outputs only when the “HD Resolution” is set to “480p”.
59
DVD Onscreen Setup Menus—Continued
Progressive Setting
With this setting you can set the component video output to progressive or interlaced. While the “HDMI Output Setting” is set to “On”, this setting is fixed at “Progres­sive” and cannot be changed. See page 30 for more information.
Interlace:
Component video output is interlaced.
Progressive (default):
Component video output is progressive.
Tip:
When the “HDMI Output Setting” is set to “Off”, you can also change this setting by using the remote control­ler’s [Resolution] button (see page 30).
HD Resolution
With this setting you can set the video resolution for the HDMI OUT. See page 30 for more information.
Auto:
The resolution is automatically set to the native resolu­tion of the TV connected to the HDMI OUT.
480p (default):
The setting displayed depends on the country in which you purchased the DVD receiver.
720 x 480p 60 Hz
720p:
1280 x 720p 50/60 Hz
1080i:
1920 x 1080i 50/60 Hz
Tip:
When the “HDMI Output Setting” is set to “On”, you can also change this setting by using the remote control­ler’s [Resolution] button (see page 30).
Note:
Initially, the DVD receiver is configured to output both HDMI and analog video. However, if after changing the resolution settings there’s no picture, with the analog video connection or HDMI connection in place, press the [Resolution] button repeatedly to restore the picture.
HD JPEG Mode
If your TV is connected to the HDMI OUT and the HDMI resolution is set to 720p or 1080i, this setting allows you to display your JPEG pictures in high defini­tion.
On:
JPEG pictures displayed in high definition.
Off (default):
JPEG pictures displayed as normal.
Notes:
• If your TV is connected to a video output other than the HDMI OUT, or the HDMI output resolution is set to something other than 720p or 1080i, even if this set­ting is set to “On”, your JPEG pictures will not be dis­played in high definition.
• When using HD JPEG, it may take a while to display each picture. And the Zoom function cannot be used. Also, onscreen status messages such as “Play” and “Stop” are not displayed.
Video Black Level
With this setting you can adjust the picture blackness for the analog video outputs. It does not affect the compo­nent video output when its set to progressive.
Light:
Blacks are lighter, and the entire picture becomes lighter.
Dark:
Blacks are darker, and the entire picture becomes darker.
Brightness
With this setting you can adjust the picture brightness.
Level 1-7:
“1” is the darkest. “7” is the brightest. The default bright­ness is “4 (standard)”.
Sharpness
With this setting you can adjust the picture sharpness.
Level 1-7:
“1” is the softest. “7” is the sharpest. The default sharp­ness is “4 (standard)”.
60
DVD Onscreen Setup Menus—Continued
Audio Menu
Digital/HDMI Audio Out
With this setting you can configure the HDMI digital output.
All (default):
Dolby Digital and DTS signals are output as they are. If your TV or amp doesn’t support higher sampling rates, set the “Linear PCM Out” setting to “Down Sample On”
(below).
PCM:
Dolby Digital and DTS signals are down mixed to 2 channels and output as PCM. If your TV doesn’t support Dolby Digital and DTS, choose this option. Audio from speakers connected to DVD receiver is also changed to PCM.
Note:
MPEG is output as PCM regardless of this setting.
Linear PCM Out
With this setting you can configure the DVD receiver to output digital audio with higher sampling rates (e.g.,
88.2 kHz, 96 kHz) as it is or to down sample it to 48 kHz or below.
If the TV you connect to the DVD receiver’s HDMI out­put supports 96 kHz digital audio, select “Down Sample Off”. Otherwise, select “Down Sample On”.
Down Sample On:
Source of 48 kHz or more is down sampled to 48 or
44.1 kHz.
Down Sample Off (default):
Sources are output as they are.
Notes:
• Some copy-protected DVD-Video discs may use 96 kHz digital audio only for D/A conversion to the analog audio outputs.
• With some discs, even if you select “Down Sample Off”, the digital audio will be down sampled, and in some cases may not be output by the DVD receiver’s HDMI output.
Language Menu
On-Screen Language
With this setting you can select a language for the onscreen setup menus and messages.
Select one of the displayed languages.
Select “Others” if the language you want is not dis­played. See “Selecting Other Languages” on page 62.
Notes:
• Not all DVD-Video discs have menus in multiple lan­guages.
• Even if a DVD-Video disc has menus in multiple lan­guages, this setting may not always work.
• If a DVD has only one menu language, that will be used.
• With some DVD-Video discs you can select languages from a menu.
Audio Language
With this setting you can select your preferred language for soundtracks. When you play a DVD-Video disc with multiple language soundtracks, your preferred language will be selected automatically. Select “Others” if the language you want is not dis­played. See “Selecting Other Languages” on page 62.
Notes:
• Not all DVD-Video discs have soundtracks in multiple languages.
• Even if a DVD-Video disc has soundtracks in multiple languages, this setting may not always work.
• If a DVD has only one soundtrack, that will be used.
• With some DVD-Video discs you can select languages from a menu.
Subtitle Language
With this setting you can select your preferred language for subtitles. When you play a DVD-Video disc with multiple language subtitles, your preferred language will be selected automatically. Select “No Subtitle” if you don’t want subtitles dis­played. Select “Others” if the language you want is not displayed. See “Selecting Other Languages” on page 62.
Notes:
• Not all DVD-Video discs have subtitles.
• Even if a DVD-Video disc has subtitles in multiple languages, this setting may not always work.
• If a DVD has only one subtitle language, that will be used.
• With some DVD-Video discs you can select subtitles from a menu.
Disc Menu Language
With this setting you can select your preferred language for disc menus. When you play a DVD-Video disc with multiple language disc menus, your preferred language will be selected automatically.
61
DVD Onscreen Setup Menus—Continued
Selecting Other Languages
This section explains how to select other languages for disc menus, audio, and subtitles.
1
Remote controller
Select “Others” from the “Disc Menu Language”, “Audio Lan­guage”, or “Subtitle Language” menu, and then press [Enter].
2
Use the Left/Right [ ]/[ ] buttons to select the code.
Use the Up/Down [ ]/[ ] buttons to enter a language code.
See adjacent table for language codes.
3
When you’ve finished, press the [Enter] button.
Use this list when specifying other languages.
Language Code Language Code
Japanese JA Kirghiz KY English EN Latin LA French FR Lingala LN German DE Laothian LO Italian IT Lithuanian LT Spanish ES Latvian LV Chinese ZH Malagasy MG Dutch NL Maori MI Portuguese PT Macedonian MK Swedish SV Malayalam ML Russian RU Mongolian MN Korean KO Moldavian MO Greek EL Marathi MR Afar AA Malay MS Abkhazian AB Maltese MT Afrikaans AF Burmese MY Amharic AM Nauru NA Arabic AR Nepali NE Assamese AS Norwegian NO Aymara AY Occitan OC Azerbaijani AZ Oromo OM Bashkir BA Oriya OR Byelorussian BE Panjabi PA Bulgarian BG Polish PL Bihari BH Pashto, Pushto PS Bislama BI Quechua QU Bengali BN Rhaeto-Romance RM
Language Code Language Code
Tibetan BO Kirundi RN Breton BR Romanian RO Catalan CA Kinyarwanda RW Corsican CO Sanskrit SA Czech CS Sindhi SD Welsh CY Sangho SG Danish DA Serbo-Croatian SH Bhutani DZ Sinhalese SI Esperanto EO Slovak SK Estonian ET Slovenian SL Basque EU Samoan SM Persian FA Shona SN Finnish FI Somali SO Fiji FJ Albanian SQ Faroese FO Serbian SR Frisian FY Siswati SS Irish GA Sesotho ST Scots-Gaelic GD Sundanese SU Galician GL Swahili SW Guarani GN Tamil TA Gujarati GU Telugu TE Hausa HA Tajik TG Hindi HI Thai TH Croatian HR Tigrinya TI Hungarian HU Turkmen TK Armenian HY Tagalog TL Interlingua IA Setswana TN Interlingue IE Tonga TO Inupiak IK Turkish TR Indonesian IN Tsonga TS Icelandic IS Tatar TT Hebrew IW Twi TW Yiddish JI Ukrainian UK Javanese JW Urdu UR Georgian KA Uzbek UZ Kazakh KK Vietnamese VI Greenlandic KL Volapük VO Cambodian KM Wolof WO Kannada KN Xhosa XH Kashmiri KS Yoruba YO Kurdish KU Zulu ZU
62
DVD Onscreen Setup Menus—Continued
Display Menu
On-Screen Display
With this setting you can turn on or off onscreen mes­sages, such as “Play”, “Stop”, and “Resume”.
Off:
Onscreen messages are not displayed.
On (default):
Onscreen messages are displayed.
On-Screen Display Color
With this setting you can set the color and theme of the Disc navigation window.
Sapphire
Pearl
Amethyst
Garnet
Background
With this setting you can select the color of the back­ground that’s displayed when the DVD receiver is stopped.
Blue
Gray
Graphic:
The theme picture specified for the “On-Screen Display Color” setting is used.
Screen Saver
With the Screen Saver function you can protect your TV against screen burn-in, which can occur when the same image or menu is displayed for a long time.
Off:
Screen saver off.
On (default):
Screen saver on. When the “Screen Saver” function is set to “On”, and playback is stopped for 15 minutes, the Screen Saver
function automatically displays a moving image. Once the screen saver has been activated, you can cancel
it by pressing either the Play [ ] button.
63
DVD Onscreen Setup Menus—Continued
Operation Setting Menu
Setting the Parental Lock
With the Parental Lock function you can block access to certain scenes that the authors have flagged as being unsuitable for children.
1
2
Remote controller
3
Select “Operation Setting” menu in the setup.
Use the Up/Down [ ]/[ ] but­tons to select “Parental Lock”, and then press the [Enter] but­ton.
The password (security code) input screen appears.
Enter the security code using the remote controller’s number but­tons, and then press the [Enter] button.
The default security code is “8888”. You can change the security code in the next section.
• Discs with parental lock may cut certain scenes, replace certain scenes with children-friendly scenes, or prevent playback of the entire disc.
Change the Security Code
To change the Security Code, confirm your existing code then enter a new one.
1
2
Remote controller
3
Select “Operation Setting” menu in the setup.
Use the Up/Down [ ]/[ ] but­tons to select “Security Code”, and then press the [Enter] but­ton.
The password (security code) input screen appears.
Enter the existing security code using the remote controller’s number buttons, and then press the [Enter] button.
The default security code is “8888”. Even if a new security code has been entered, the code “8888” can still be used.
Once the security code has been entered, the new security code input screen appears.
4
Notes:
• When entering a security code, you can use the [CLR] button to delete the numbers entered so far, if neces­sary.
• Not all discs use parental lock. See the disc’s sleeve notes for details.
Use the Up/Down [ ]/[ ] but­tons to change the level of paren­tal lock, and then press the [Enter] button.
At level 8 parental lock is off, with level 1 being the strictest level.
64
4
Note:
If you forget your security code, enter “8888” instead. “8888” is a security code that can always be used.
Enter the new security code using the remote controller’s number buttons, and then press the [Enter] button.
The new security code has been set.
DVD Onscreen Setup Menus—Continued
DVD Priority Contents
This setting determines what is played when a DVD-Audio disc also contains DVD-Video material.
DVD-AUDIO (default):
The DVD-Audio material is played.
DVD-VIDEO:
The DVD-Video material is played.
SACD Priority Contents
SACDs have two separate areas for storing audio tracks—one for multichannel audio, the other for 2­channel stereo audio. In addition, hybrid SACDs have an extra layer for playback in standard CD players.
With this setting you can determine how SACDs are played by the DVD receiver.
2 ch Area (default):
The 2-channel stereo audio tracks are played.
Multi ch Area:
The multichannel audio tracks are played.
CD Area:
The CD layer of hybrid SACDs is played.
Note:
This setting determines which area of the disc is played initially. If “Multi ch Area” is selected, and an SACD that contains no multichannel area is loaded, the 2-chan­nel area will be played.
65
Additional information
Resetting the receiver
Use this procedure to reset all the receiver’s settings to the factory default. Note that resetting the DVD receiver will delete your radio presets and custom settings.
1
2
DVD receiver
Turn on the DVD receiver.
Using the front panel buttons, hold down the [Stop] button and press [Standby/On] button.
“DVD Clear” appears on the display. When the reset is complete, and the DVD receiver enters Standby mode.
HOLD
DVD-Video regions
All DVD-Video discs carry a region mark on the case somewhere that indicates which region(s) of the world the disc is compatible with. Your DVD receiver also has a region mark, which you can find on the rear panel. Discs from incompatible regions will not play in this receiver. Discs marked “ALL” will play in any player. The diagram below shows the various DVD regions of the world.
Disc Content Organization
DVD-Video Format
DVD-Video discs contain titles, which are usually sub­divided into chapters.
Title 1
Chapter 1 Chapter 2 Chapter 1 Chapter 2
DVD -Vi deo
DVD-Audio
DVD-Audio discs contain groups and tracks.
Track 1
Group 1
Track 2 Track 3 Track 1 Track 2
DVD -Au dio
SACD
SACDs have two separate areas for storing audio tracks—one for multichannel audio, the other for 2­channel stereo audio. In addition, hybrid SACDs have an extra layer for playback in standard CD players.
Multichannel area Stereo area
Track 1 Track 2 Track 3
CD layer of a hybrid SACD
SACD
VCD
VCDs contain video tracks.
Track 1 Track 2 Track 3 Track 4
Title 2
Group 2
Track 1 Track 2 Track 3
66
1
2
4
2
5
6
3
5
1
2
Audio CD Format
4
Audio CDs contain tracks.
Track 1 Track 2 Track 3 Track 4 Track 5
Video CD
Audio C D
Additional information—Continued
MP3, WMA & JPEG Files
MP3, WMA and JPEG files are typically organized into folders. The DVD receiver handles MP3, WMA and JPEG files as tracks.
ROOT 001
MP3/WMA/JPEG (CD-R/RW, DVD-R/RW, DVD+R/RW)
Folde r 1
Tra c k
001
Folde r 2
002
004
001.mp3 (001.wma)
010.mp3 (010.wma)
011.mp3 (011.wma)
012.mp3 (012.wma)
020.mp3 (020.wma)
Glossary
Analog audio
An electrical signal that directly represents sound. Com­pare this to digital audio which can be an electrical sig­nal, but is an indirect representation of sound. See also “Digital audio.”
Aspect ratio
The width of a TV screen relative to its height. Conven­tional TVs are 4:3 (in other words, the screen is almost square); widescreen models are 16:9 (the screen is almost twice as wide as it is high).
Digital audio
An indirect representation of sound by numbers. During recording, the sound is measured at discrete intervals (44,100 times a second for CD audio) by an analog-to­digital converter, generating a stream of numbers.
On playback, a digital-to-analog converter generates an analog signal based on these numbers. See also “Sam­pling frequency” and “Analog audio.”
Dolby Digital
Using a maximum of 5.1 channels of audio, this high quality surround system is used in many of the finer movie theaters around the world.
The display shows which channels are active, for exam­ple showing 3/2.1. The 3 being the two front channels and the center channel; the 2 being the surround chan­nels, and the .1 being the LFE channel.
Down Mix
Down mixing reduces the number of surround-sound channels and mixes the multi-channel audio that is used in Dolby Digital and DTS so that the audio matches the number of speakers and other elements of the output environment.
DRM
DRM (digital rights management) is a type of server software developed to enable secure distribution of paid content over the web, recently incorporated by WMA (Windows Media Audio).
DTS
DTS stands for Digital Theater Systems. DTS is a sur­round system different from Dolby Digital that has become a popular surround sound format for movies.
67
Glossary—Continued
Dynamic range
The difference between the quietest and loudest sounds possible in an audio signal (without distorting or getting lost in noise).
Dolby Digital and DTS soundtracks are capable of a very wide dynamic range, delivering dramatic cinema-like effects.
File extension
A tag added to the end of a filename to indicate the type of file. For example, “.mp3” indicates an MP3 file.
HD
Abbreviation for high definition, as in HDTV (high-def­inition TV).
HDCP (High-bandwidth Digital Content Protection)
The video encryption technology developed by Intel for HDMI/DVI. It’s designed to protect video content and requires a HDCP-compatible device to display the encrypted video.
HDMI
HDMI (High-Definition Multimedia Interface) is a high­speed digital interface which has the capability to sup­port standard, enhanced, or high-definition video plus standard to multichannel surround-sound audio on a sin­gle digital connection. HDMI features include uncom­pressed digital video, a bandwidth of up to 5 gigabytes per second and communication between the AV source and AV devices such as DTVs.
ISO 9660 format
International standard for the volume and file structure of CD-ROM discs.
JPEG
A file format used for still images, such as photographs and illustrations. JPEG files are identified by the file extension “.jpg” or “.JPG”. Most digital cameras use this format.
LFE
LFE refers to the low-frequency effect sounds that are used in Dolby Digital and DTS. Generally, the subwoof­ers function more effectively when these sounds are con­tained in the signal from the disc or other media.
MP3
MP3 (MPEG1 audio layer 3) is a compressed audio file format. Files are recognized by their file extension “.mp3” or “.MP3”.
MPEG video
The video format used for Video CDs and DVDs. Video CD uses the older MPEG-1 standard, while DVD uses the newer and much better quality MPEG-2 standard.
NTSC (National Television Standards Committee)
This is one broadcasting system for color televisions, and is used in the U.S., Korea, Central and South Amer­ica, Japan, and other countries.The system consists of 525 horizontal scan lines, and is divided into 30 frames per second. It uses an interlacing method which skips every other scan line to produce an image (field) with one-half of the full resolution, and displays 60 such fields per second.
PAL (Phase alternation by line)
This is one broadcasting system for color televisions, and is used primarily in Europe.This system consists of 625 horizontal scan lines. It uses an interlacing method with 25 frames (50 fields) per second.The vertical reso­lution is higher than NTSC, however the frame rate is lower.
PBC (PlayBack Control) (Video CD only)
A system of navigating a Video CD through on-screen menus recorded onto the disc. Especially good for discs that you would normally not watch from beginning to end all at once—karaoke discs, for example.
PCM (Pulse Code Modulation)
The most common system of encoding digital audio, found on CDs and DAT. Excellent quality, but requires a lot of data compared to formats such as Dolby Digital.
Progressive scan video
All the lines that make up a video picture are updated in one pass (compared to interlace which takes two passes to update the whole picture).
Regions (DVD-Video only)
These associate discs and players with particular areas of the world. This unit will only play discs that have com­patible region codes. You can find the region code of your unit by looking on the rear panel. Some discs are compatible with more than one region (or all regions).
Sampling frequency
The rate at which sound is measured to be turned into digital audio data. The higher the rate, the better the sound quality, but the more digital information is gener­ated. Standard CD audio has a sampling frequency of
44.1kHz, which means 44,100 samples (measurements) per second. See also “Digital audio.”
T-D (Theater-Dimensional)
This is a virtual surround-sound technology that was developed by Onkyo Corporation. For details, see page 41.
WMA
WMA is short for Windows Media Audio and refers to an audio compression technology developed by Microsoft Corporation. WMA data can be encoded by using Windows Media Player version 8.
68
Troubleshooting
If you have any trouble using the DVD receiver, look for a solution in this section. If you can’t resolve the issue yourself, contact the dealer from whom you purchased this unit.
The DVD receiver does not work or shows no reac­tion.
DVD re ceiv er
HOLD
Press and hold [Stop] button for 10 seconds to forcibly shut down the DVD receiver.
Power
The power to the system is not turned on
• Make sure that the power cord is plugged into the AC outlet. Make sure that the other end of the power cord is properly connected to the DVD receiver’s AC INLET (page 23).
• Unplug the power cord from the AC outlet, wait for 10 seconds or more, then plug the cable in again.
The power is turned off during the operation
• If the SLEEP indicator is lit on the display, the Sleep timer is functioning. Cancel the Sleep timer (page 32).
• If the Standby indicator is blinking on and off, the built-in protection circuit is activated. Be careful not to short the positive and negative wires.
The DVD receiver turns off as soon as it’s turned on
• The amp protection circuit has been activated. Remove the power cord from the wall outlet immedi­ately. Disconnect all speaker cables and input sources, and leave the DVD receiver with its power cord dis­connected for 1 hour. After that, reconnect the power cord and set the volume to maximum. If the DVD receiver stays on, set the volume to minimum, discon­nect the power cord, and reconnect your speakers and input sources. If the DVD receiver turns off when you set the volume to maximum, disconnect the power cord, and contact the dealer from whom you pur­chased this unit.
Audio
The sound is not heard or very quiet
• Make sure the power cord is plugged into an AC out­let.
• Make sure that all audio connecting plugs are pushed in all the way (page 23).
• Make sure that none of the connecting cables are bent, twisted, or damaged.
• Make sure that the speakers are connected correctly and the speaker cables’core wires touch only the speaker connectors (page 17).
• Check to make sure that the volume level is not set to minimum (page 31).
• Make sure that the input source is properly selected (page 31).
• Check to make sure the muting function is not engaged. If the MUTING indicator is flashing, the sound is muted. Cancel the muting function (page 32).
• When the headphones are connected, the speakers do not output any sound. Disconnect the headphones (page 31).
• Make sure that the digital input source is assigned properly (page 56).
• Check the digital audio output setting on the con­nected device. On some game consoles, such as those that support DVD, the default setting is off.
• The audio signal input from HDMI IN is not output from the speakers connected to the DVD receiver. Make the analog or digital connection (pages 24, 25).
There’s no sound with a certain signal format
• Check the digital audio output setting on the con­nected device. On some game consoles, such as those that support DVD, the default setting is off.
Sound is not good
• Make sure that the speaker cords are connected cor­rectly. Check their polarity (+/
• Connect the analog audio cables (RCA) firmly (page 23).
• Sound quality could be affected by a strong magnetic field, such as a TV set. Locate such a device far from the DVD receiver.
• If you have any devices that emit high intensity radio waves near the DVD receiver, such as a cellular phone in operation (calling), noise may be generated.
• The DVD receiver uses a rotating unit whose precision instrument generates faint hissing sound while reading a disc during playing back or searching a track; you may hear it in a silent environment.
• Using cable ties to bundle audio cables with power cord, speaker cables, and so on may degrade the audio performance, so don’t do it.
) (page 17).
69
Troubleshooting—Continued
The subwoofer produces no sound
• When you play source material that contains no infor­mation in the LFE channel, the subwoofer produces no sound.
• Make sure the subwoofer is configured correctly (page 54).
Headphones makes noise or no sound
• There may be a bad contact. Clean up the headphones terminal. For information on how to clean up, see the instruction manual attached to the headphones. Other­wise, verify the cord of the headphones which may be broken.
Sound Quality
• The sound quality becomes stable when 10 to 30 min­utes have passed after the power was turned on.
• Using cable ties to bundle audio cables with speaker cables may degrade the audio performance, so don’t do it.
The Late Night function doesn’t work
• Make sure the source material is Dolby Digital.
The beginning of audio received by an HDMI IN can’t be heard
• Since it takes longer to identify the format of an HDMI signal than it does for other digital audio sig­nals, audio output may not start immediately.
There’s no sound to your TV connected to an HDMI OUT
• You won’t hear any sound from the HDMI OUT if your TV only supports DVI.
• Change the HDMI setting on your TV to HDMI.
• Your TV doesn’t support Dolby or DTS. Change the “Digital/HDMI Audio Out” setting to “PCM” (page 61).
• Your TV doesn’t support 88.2 kHz, 96 kHz, 176.4 kHz or 196 kHz PCM. Change the “Linear PCM Out” setting to “Down Sample On” (page 61).
Video
There’s no picture
• Make sure that all video connecting plugs are pushed in all the way (page 23).
• Make sure that each video component is properly con­nected. (pages 23-26)
• If the video source is connected to an HDMI IN, your TV must be connected to the HDMI OUT (page 26). Your TV input must be changed to HDMI.
• On your TV, make sure that the video input to which the DVD receiver is connected is selected.
There’s no picture from a source connected to an HDMI IN
• The TV or display does not support the current video resolution and you need to select another resolution on your AV component.
There’s no picture to your TV connected to an HDMI OUT
• The HDMI Output Setting is set to Off or your TV doesn’t support HDMI Resolution settings of 720p and 1080i (page 30).
• Try pressing the [HDMI] button on the front panel repeatedly to switch the HDMI Output Setting to on, and then pressing the [Resolution] button on the remote controller repeatedly to get picture (page 30).
• If the DVD receiver is connected to your AV compo­nent, try connecting it directly to your TV. It will not work if you connect to a component that doesn’t sup­port HDCP (page 26).
There’s no picture to your TV connected to an Component Video Output
• Your TV does not support progressive scanning, and the HDMI Output Setting is on. While the HDMI Output Setting is on, the component video output outputs progressive video. Try pressing the [HDMI] button on the front panel repeatedly to switch the HDMI Output Setting to off, and then pressing the [Resolution] button repeatedly to switch to Interlaced (page 30).
• Press the [Resolution] button repeatedly to select 480p (page 30).
There’s no picture to your TV connected to an Composite Video Output
• Try pressing the [Resolution] button on the remote controller repeatedly to get picture (page 22).
70
Troubleshooting—Continued
Tune r
Reception is noisy, FM stereo reception is noisy, or the FM ST indicator doesn’t appear
• Relocate your antenna.
• Move the DVD receiver away from your TV or com­puter.
• When listening to an AM station, operating the remote controller may cause noise.
• Passing cars and airplanes can cause interference.
• Concrete walls weaken radio signals.
• If nothing improves the reception, install an outdoor antenna.
Remote Controller
The remote controller doesn’t work
• Make sure that the batteries are installed with the cor­rect polarity (page 11).
• Install new batteries. Don’t mix different types of bat­teries, or old and new batteries (page 11).
• Make sure that the remote controller is not too far away from the DVD receiver, and that there’s no obstruction between the remote controller and the DVD receiver’s remote control sensor (page 11).
• Make sure that the DVD receiver is not subjected to direct sunshine or inverter-type fluorescent lights. Relocate if necessary.
• If the DVD receiver is installed in a rack or cabinet with colored-glass doors, the remote controller may not work reliably when the doors are closed.
• When using the remote controller to control other manufacturers’ AV components, some buttons may not work as expected.
Can’t control a TV
• Make sure you’ve entered the correct remote control code.
• To control another manufacturer’s TV, point the remote controller at the component. Be sure to enter the appropriate remote control code first (page 52).
Can’t control an RI Dock
• Make sure that the cable and analog audio cable are connected properly. Connecting only an cable won’t work (page 25).
• To control an RI Dock that’s connected via , point the remote controller at the DVD receiver.
The functions don’t work
• To use , you must make an connection and an analog audio connection (RCA) between the compo­nent and DVD receiver, even if they are connected digitally (page 25).
Disc Playback
The disc won’t play or is automatically ejected after loading
• Make sure the disc is free from dirt and dust and is not damaged (page 9).
• Make sure the disc is loaded with the label side face up and aligned properly in the disc tray guide.
• If the region number on a DVD-Video disc does not match the number on the receiver, the disc cannot be used (page 66).
• Condensation inside the receiver: Allow time for con­densation to evaporate. Avoid using the receiver near an air-conditioning unit.
• Reload the disc with the label side face up.
• If the Parental Lock function is active, defeat it or change the level (page 64).
The disc doesn’t play in the correct order
• Defeat special playback modes such as Repeat Play, Memory Playback, and Random Playback (pages 45–47.)
Track numbers cannot be stored when setting Memory Playback
• Make sure that the disc has been loaded, and the track(s) you try to program are included on the disc.
It takes a long time until playback starts
• It may take time for the DVD receiver to load and read a CD or DVD that contains many tracks.
New settings made in the onscreen setup menus while a disc is playing are ineffective
• Some settings can be changed while a disc is playing, but are not effective until the disc is stopped then restarted: Press the Stop [ ] button, then start play­back again.
Screen is stretched or aspect does not change
• The “TV Shape” setting in the onscreen setup menu is incorrect. See page 59 for how to set it correctly for your TV/monitor.
Picture disturbance during playback or the picture is dark
• This receiver is compatible with Macro-Vision Sys­tem copy guard. Some discs include a copy prevention signal, and when this type of disc is played back, stripes etc., may appear on some sections of the pic­ture depending on the TV. This is not a malfunction.
• Due to the receiver’s copy protection circuits, connec­tion of this device through a VCR or an AV selector may prevent recording or cause picture problems. This is not a malfunction.
71
Troubleshooting—Continued
No sound, or sound is distorted
• No sound is output when scanning discs other than audio CDs and SACDs.
• Check that the disc is free from dust and dirt, and that it is not damaged (page 9).
• Check that the plugs and terminals are free of dirt, oxide, etc. and clean if necessary. Also check the cable for damage.
Noticeable difference in DVD and CD volume
• This is due to differences in the audio format and is not a malfunction.
DVD-Audio playback stops
• The disc may have been illegally copied.
Can’t watch the DVD-Video
• With some DVD-Video Discs, you need to select an audio output format from a menu.
Can’t watch the DVD-Video material on a DVD-Audio disc
• Set the “DVD Priority Contents” setting to “DVD-VIDEO” (page 65).
Can’t play the multichannel area of a hybrid SACD
• Set the “SACD Priority Contents” setting to “Multi ch Area” (page 65).
Can’t play MP3 and JPEG discs
• Use only ISO 9660 Level 2 format discs (page 9).
• The disc has not been finalized. Finalize the disc (page 9).
Can’t select MP3 files
• MP3 files without a “.mp3” or “.MP3” filename exten­sion are not recognized.
• The MP3 disc is a multisession disc. Only files in the first session of a multisession disc can be played (page 9).
Can’t play WMA files
• WMA files without a “.wma” or “.WMA” filename extension are not recognized.
• The WMA file’s copyright option is on. Don’t use the copyright option (page 9).
Can’t view JPEG files
• JPEG files without a “.jpg” or “.JPG” or “.JPEG” file­name extension are not recognized.
• The JPEG file is too big. Use JPEG files that are less than 5 megabytes (page 9).
Connection with External Devices
No sound is heard from the connected device
• Make sure that the optical digital cable is not bent over or damaged.
• Set the “Digital/HDMI Audio Out” to “PCM”, because the TV supports only PCM signals (page 61).
The turntable sounds still
• Make sure if the turntable has built in phono equalizer.
• If the turntable has no phono equalizer built in, you must provide one separately.
The turntable makes no sound
• If your turntable uses an MC cartridge, you must con­nect an MC transformer or an MC head amp.
The Colors of the TV Picture Bleed
• Locate the speakers far from the TV.
The DVD receiver contains a microcomputer for signal processing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this happens, unplug the power cord from the wall outlet, wait at least five seconds, and then plug it back in again.
Before disconnecting the power cord from the wall out­let, set the DVD receiver to Standby.
72
Troubleshooting—Continued
HDMI Status Mode
If you’re using an HDMI connection and there’s no picture or sound, you can check the status of the HDMI connection by pressing and holding down the DVD receiver’s [Display] button for 10 seconds until a message ID appears on the display. Look up the message ID in the following tables and check the HDMI connections and settings on both the DVD receiver and the connected component.
HDMI connection and HDMI-related settings status
Displayed ID Message
MSG ID 001 MSG ID 015
MSG ID 021 Input is selected other than DVD or VIDEO1. No output from HDMI OUT.
MSG ID 022
MSG ID 023 Check the settings and connections of the TV and component connected to DVD receiver.
No picture from the HDMI connection
Displayed ID Message
MSG ID 002 The “HDMI Output Setting” is set to “Off”. Change it to “On” (page 30).
MSG ID 003 MSG ID 004
MSG ID 005 MSG ID 006 MSG ID 007
MSG ID 008
MSG ID 009
Turn the DVD receiver and the connected component off, then turn them on again. Make sure that the connected component is working properly and that the DVD receiver’s HDMI settings are con­figured suitably for that component.
When the DVD or VIDEO1 input is selected, the “HDMI Output Setting” is set to “Off”. Change it to “On” (page 30).
The HDMI cable may not be connected properly. Check the connection. Also, make sure the HDMI input on the TV is correctly configured to received HDMI.
Make sure the HDMI input on the TV is correctly configured to received HDMI. The connected component may not support HDCP. Make sure the connected component supports HDCP. Turn the DVD receiver and the connected component off, then turn them on again. The DVD receiver may be connected to the other component’s DVI jack. Some TVs may not prop­erly receive the video output by the DVD receiver. Also, with a DVI connection, there will be no sound.
The DVD receiver’s “HD Resolution” setting is set to “720p” or “1080i”. If your TV doesn’t support these resolutions, select another resolution (page 30).
The connected component may not be receiving the HDMI signal properly. Try selecting another resolution on the DVD receiver (page 30).
No sound from the HDMI connection
Displayed ID Message
MSG ID 011 MSG ID 014
MSG ID 012 MSG ID 013
MSG ID 016 MSG ID 017
MSG ID 020 Audio from SACDs is not output by the HDMI OUT.
The connected component may not support 96 kHz PCM. Set the DVD receiver’s “Linear PCM Out” setting to “Down Sample On” (page 61).
The connected component may not support Dolby Digital. Set the DVD receiver’s “Digital/HDMI Audio Out” setting to “PCM” (page 61).
The connected component may not support DTS. Set the DVD receiver’s “Digital/HDMI Audio Out” setting to “PCM” (page 61).
73
Specifications
Amplifier Section
Rated output Power (FTC)
THD (Total Harmonic Distortion)
Input Sensitivity and Impedance
Frequency Response
Signal to Noise Ratio 106 dB (LINE, IHF-A) Speaker Impedance
50 watts minimum continuous power per channel, 6 ohm loads, 2 channels driven at 40 Hz - 20 kHz with a maximum total harmonic distortion of 0.9 %
0.9% (Power Rated)
0.08% (1 kHz, 1 W)
200 mV/47 k: (LINE) 20 Hz - 100 kHz/+0 dB - 1.5 dB (Direct mode)
6 : - 16
:
Video Section
Signal System NTSC Composite Video Output/Impedance
Component Video Output/Impedance
Component Video Frequency Response
1.0 V (p-p)/75 : negative sync, RCA
Y: 1.0 V (p-p)/75 : PB/PR: 0.7 V (p-p)/75 : RCA
5 Hz - 50 MHz - 3 dB
Tune r Sec t ion
FM Tuning Frequency Range
AM Tuning Frequency Range
Preset Channel 40
87.5 MHz - 107.9 MHz
530 kHz - 1710 kHz
Video Inputs
HDMI IN Composite VIDEO1, VIDEO2/DOCK
Video Outputs
HDMI OUT Component OUT Composite VIDEO OUTPUT
Audio Inputs
Digital Inputs Optical: 1
Coaxial: 1
Analog Inputs VIDEO1, VIDEO2/DOCK
Audio Outputs
Subwoofer Pre Output 1 Speaker Outputs FL, FR Phones 1
Control Terminal
RS232 1 IR Input/Output 1/1
Specifications and features are subject to change without notice.
General
Power Supply AC 120 V, 60 Hz Power Consumption 118 W Stand-by Power Consumption
Dimensions (W
Weight 8.6 kg (19.0 lbs.) Operation Condition Temperature and Humidity
Disc Compatibility SACD, DVD-Audio, DVD-Video, DVD-
0.4 W
u H u D)
435 u 90 u 415 mm 17-1/8" u 3-9/16" u 16-5/16"
5°C–35°C (41°F–95°F), 5%–85%
R/RW (VIDEO), DVD+R/RW, CD, CD­R/RW, Video CD, MP3, WMA, JPEG Disc that have not been property finalized may only be partially playable or not playable at all
74
Remote Control Codes List
TV
888 0264
Acura 0009
Addison
Admiral 0093, 0463
Advent
Aiko 0092
Aiwa 1916
Akai
Akura 0264
Alba 0009, 0037, 0371
Albatron 0700, 0843
Alfide 0672
America Action 0180
Amstrad
Anam
Anam National 0161, 0250, 0650
Anhua 0051
Anitech 0009
AOC
Aolinpike 0264
Apex Digital
Audinac 0180
Audiosonic 0037, 0109
Audiovox
Aventura 0171
Awa 0009
Baihe 0009, 0264
Baile 0001, 0009, 0661
Baird 0343
Baohuashi 0264
Baosheng 0009, 0817
Barco 0556
Basic Line 0009
Baur 0037, 0361, 0512
Baysonic 0180
Beaumark 0178
Beijing
0092, 0108, 0653, 1150
0761, 0783, 0815, 0817, 0842
0009, 0030, 0208, 0264, 0361, 0602, 0672, 0702, 0753, 0812, 1935
0009, 0037, 0171, 0371, 0433
0009, 0161, 0180, 0250, 0700
0009, 0030, 0060, 0092, 0093, 0108, 0178, 0180, 0451, 0474, 1150
0748, 0765, 0767, 0879, 1217
0092, 0180, 0451, 0623, 0802, 0875
0001, 0009, 0208, 0226, 0264, 0661, 0812, 0817
TV
Beko 0714
Bell & Howell 0154
BenQ 1032
Beon 0037
Blaupunkt 0195
Blue Sky
BPL 0208, 0896
Bradford 0180
Brandt 0109, 0335
Broksonic 0236, 0463, 1935
Bush
C-Tech 0896
Caihong 0009, 0817
Cailing 0748
Candle 0030, 0056, 0186
Carnivale 0030
Carver 0054, 0170
Cascade 0009
Cathay 0037
CCE 0037
Celebrity 0000
Celera 0765
Celestial 0767
Centrex 0780
Centurion 0037
CGE 0074
Changcheng
Changfei 0009, 0817
Changfeng 0264, 0753, 0817
Changhai 0009, 0817
Changhong
Chengdu 0009, 0817
Ching Tai 0009, 0092, 0474
Chun Yun
Chunfeng 0009, 0264
Chung Hsin
Chunsun 0009, 0817
Cimline 0009
Cinema 0672
Cineral 0092, 0451
Citizen
0556, 1037, 1254, 1314
0009, 0037, 0371, 0698, 1037
0001, 0009, 0051, 0264, 0661, 0817
0009, 0156, 0264, 0508, 0765, 0767, 0783, 0817, 1156
0000, 0009, 0092, 0161, 0180, 0474, 0700, 0843, 1150
0053, 0108, 0180, 0474, 1150
0030, 0056, 0060, 0092, 0186, 1935
TV
Clarion 0180
Clarivox 0037
Commercial Solutions
Concerto 0056
Conrac 0808
Conrowa
Contec 0009, 0180
Craig 0161, 0180
Crosley 0054, 0074
Crown
Crown Mus­tang
Curtis Mathes
CXC 0180
Daewoo
Dansai 0037
Dayton 0009
Dayu 0661
De Graaf 0208
Decca 0037
Dell 1080, 1178
Denon 0145, 0511
Denver 0587
Dick Smith Electronics
Digatron 0037
Digital Life 0780
Digitor 0037, 0698
Digix 0880
Dixi 0009, 0037
Dongda 0009
Donghai 0009
DSE 0698
Dumont 0017
Durabrand
0047, 1447
0009, 0145, 0156, 0264, 0698, 0753, 1156
0009, 0037, 0180, 0418, 0672
0672
0030, 0047, 0054, 0056, 0060, 0093, 0145, 0154, 0166, 0451, 0702, 1147, 1347
0009, 0030, 0037, 0056, 0092, 0108, 0154, 0170, 0178, 0180, 0451, 0474, 0623, 0634, 0661, 0672, 0700, 0880, 1150, 1661
0698
0171, 0178, 0180, 0463, 1034
75
Remote Control Codes List—Continued
TV
ECE 0037
Electroband 0000
Electrograph 1755
Electrohome 0463
Elektra 0017, 1661
Elin 0037
Elta 0009
0154, 0171, 0178,
Emerson
Envision 0030, 0813
Erres 0037
ESA 0171, 0812
Ether 0009, 0030, 0161
Etron 0009
Feilang 0009
Feilu 0009, 0817
Feiyan 0264
Feiyue 0009, 0817
Ferguson
Fidelity 0361
Finlandia 0208, 0346
Finlux 0037, 0346
Firstar 0009, 0236
Firstline 0009
Fisher 0154, 0208
Flint 0455
Formenti 0037
Fortress 0093
Frontech 0264
Fujitsu
Fujitsu General 0186
Fujitsu Sie­mens
Funai
Furi 0145, 0264, 0817
Futuretech 0180
Ganxin 0817
Gateway 1755, 1756
GE
GEC 0037
Geloso 0009
General 0186
Gibralter 0017, 0030
0180, 0236, 0361, 0463, 0623
0037, 0109, 0335, 0343, 0560
0186, 0683, 0809, 0853, 1181
1163
0171, 0180, 0264, 0342
0030, 0047, 0051, 0092, 0178, 0180, 0451, 0560, 1347, 1447, 1454
76
TV
Gintai 0474, 1150
Go Video 0886
GoldStar
Goodmans
Gradiente 0053, 0056, 0170
Graetz 0361, 0714
Granada 0037, 0208
Grandin 0610, 0865, 0880
Grundig
Grunpy 0180
Haier
Haihong 0009
Haiyan 0264, 0817
Hallmark 0178
Hankook
Hanseatic
Harman/Kar­don
Harvard 0180
Harwa 0773
Havermy 0093
HCM 0009
Helios 0865
Hello Kitty 0451
Himitsu 0180
Hinari 0009, 0037
Hisawa 0455
Hisense
Hitachi
Hitec 0698
Hoeher 0865
Hongmei
Hongyan 0264, 0817
Hua Tun 0009, 1150
Huafa 0009, 0145
0001, 0030, 0037, 0056, 0109, 0154, 0178, 1150, 1378
0037, 0343, 0360, 0371, 0634
0037, 0195, 0556, 0587, 0672, 0706, 1935
0037, 0508, 0587, 0698, 0896, 1034
0030, 0056, 0178, 0180
0037, 0361, 0556, 0661, 0808
0054
0009, 0145, 0156, 0508, 0556, 0748, 0753, 0780, 1156
0009, 0030, 0056, 0092, 0109, 0145, 0156, 0178, 0186, 0225, 0474, 0508, 1037, 1145, 1150, 1156, 1245, 1256, 1378
0009, 0093, 0264, 0817
TV
Huanghaimei 0009
Huanghe 0009, 0817
Huanglong 0009
Huangshan 0009, 0264, 0817
Huanyu 0264, 0817
Huaqiang 0264
Huari 0145, 0264
Huodateji 0051
Hypson 0037, 0264
Hyundai 0849, 0865
ICE 0264, 0371
Imperial 0074, 0418
Imperial Crown
Indiana 0037
Infinity 0054
Innova 0037
Insignia 0171
Inteq 0017
Interfunk 0037, 0361, 0512
Intervision 0037, 0264
IRT 0451, 0698, 1661
ITS 0371
ITT 0361
JBL 0054
JCB 0000
Jean
Jensen 0761, 0815, 0817
Jiahua 0051
JiaLiCai 0009, 0264
Jinfeng
Jinque 0009, 0264, 0817
Jinta 0009, 0264
Jinxing
Juhua 0264, 0817
JVC
0001, 0009, 0264, 0661
0009, 0051, 0092, 0156, 0236, 0474
0051, 0208, 0226, 0817
0009, 0037, 0054, 0145, 0156, 0264, 0556, 0698, 0817
0053, 0160, 0371, 0463, 0508, 0606, 0653, 0683, 0731, 1172, 1253
Remote Control Codes List—Continued
TV
Kaige 0009, 0264, 0817
Kaisui 0009
Kanghua 0896
Kangli
Kangyi 0009, 0264
Karcher 0610
Kathrein 0556
KEC 0180
Kendo 0037
Kenwood 0030
Khind 0706, 0896
Kioto 0054, 0556, 0706
KLH 0765, 0767
KLL 0037
Kolin
Kongque 0009, 0264, 0817
Konka 0037, 0587, 0817
Korpel 0037
Kost 1262, 1483
Koyoda 0009
KTV 0030, 0180
Kuaile 0009, 0264
Kulun 0009
Kunlun
L&S Electronic 0808
Leyco 0037, 0264
LG
Liesenk & Tter 0037
Lihua 0817
Local India TV
Local Malaysia TV
Loewe
Logik 0001, 1217
Longjiang 0264, 0817
Luxman 0056
Luxor 0361
LXI
0001, 0009, 0264, 0661, 0817
0053, 0108, 0150, 0180, 0474, 1150, 1331
0051, 0208, 0226, 0264, 0661, 0817
0001, 0030, 0037, 0056, 0060, 0108, 0178, 0442, 0474, 0644, 0700, 0714, 0856, 1178, 1265, 1378
0009, 0208, 0264, 0371, 0602
0698
0136, 0512, 0633, 0790
0047, 0054, 0154, 0156, 0178
TV
M & S 0054
M Electronic
Magnavox
Manesth 0264
Marantz
Mark 0037
Mastro
Matsui
Matsushita 0161, 0250, 0650
Maxent 1755
Meck 0698
Mediator 0037
Medion
Megapower 0700
Megatron 0145, 0178
Meile 0264, 0817
Memorex
Mercury 0001
Mermaid 0037
Metronic 0625
Metz 0388, 0447, 0746
MGA 0030, 0150, 0178
Micromaxx 0808
Microstar 0808
Midland 0017, 0047, 0051
Mitsubishi
Monivision 0700, 0843
Motorola 0093
MTC
Mudan
Multitech 0009, 0180
Murphy 0474
Myryad 0556
NAD
Nanbao 0009, 0264
0009, 0037, 0109, 0346, 0480
0030, 0054, 0186, 0706, 0780, 0802, 1254, 1454
0030, 0037, 0054, 0556, 0704, 0855
0053, 0698, 0706, 0780
0009, 0035, 0037, 0208, 0371, 0443
0808, 0880, 1037, 1248
0009, 0150, 0154, 0178, 0463, 1037
0030, 0056, 0093, 0108, 0150, 0154, 0178, 0180, 0236, 0250, 0474, 0512, 0817, 0836, 1150, 1171, 1182, 1250
0030, 0056, 0060, 0512
0009, 0051, 0208, 0226, 0264, 0817
0156, 0178, 0361, 0866
TV
Nansheng 0264, 0817
National
NEC
Neckermann 0037, 0556
NEI 0037
Neovia 0865
Netsat 0037
NetTV 1755
Newave
Nikkai 0035, 0037, 0264
Nikko 0030, 0092, 0178
Noblex 0154
Nokia 0361, 0480, 0606
Norcent 0748, 0824
Nordmende 0109, 0343, 0560
NTC 0092
Oceanic 0361
Olevia 1144, 1240, 1331
Onida 0053, 1253
Onwa 0180, 0433
Optimus
Optonica 0093
Orion
Osaki 0264, 0474
Otto Versand
0051, 0208, 0226, 0508
0009, 0030, 0051, 0053, 0056, 0154, 0156, 0170, 0178, 0186, 0264, 0455, 0474, 0508, 0704, 0817, 1150, 1378, 1456, 1704
0009, 0092, 0093, 0161, 0178, 1150
0154, 0166, 0250, 0650
0037, 0236, 0443, 0463, 0474, 0880, 1463
0037, 0343, 0512, 0556
77
Remote Control Codes List—Continued
TV
Palladium 0418
Palsonic 0773
Panama 0264
0037, 0051, 0054, 0161, 0208, 0226,
Panasonic
Panda
Pausa 0009
Penney
Philco
Philips
Phonola 0037
Pilot 0030, 0706
Pioneer
Polaroid
Portland 0092
Prima
Princeton 0700
Prism 0051
Profex 0009, 0361
Proscan 0047, 1347, 1447
Protech
Proton
Proview 1498
Pulsar 0017
Pye 0037
Qingdao
Quasar 0051, 0250, 0650
Quelle
R-Line 0037
0250, 0508, 0650, 0896, 1168, 1175, 1177
0009, 0051, 0208, 0226, 0264, 0508, 0698, 0706, 0780, 0817
0030, 0047, 0051, 0060, 0156, 0178, 1347, 1378
0030, 0037, 0054, 0056, 0074, 0145, 0178, 0180, 0186, 0463, 0474, 1661
0000, 0030, 0037, 0051, 0054, 0056, 0092, 0108, 0178, 0186, 0474, 0556, 0690, 1454, 1483
0109, 0166, 0679, 0760, 0866
0765, 0865, 1262, 1276, 1314, 1341, 1498
0761, 0783, 0815, 0817
0009, 0037, 0264, 0418
0001, 0009, 0030, 0056, 0178, 0474, 0644
0051, 0208, 0226, 0264, 0817
0037, 0074, 0361, 0512
TV
Radiola 0037
RadioShack
RCA
Realistic
Rediffusion 0361
Relisys 0865
Reoc 0714
Revox 0037
Rex 0264
Roadstar 0009, 0264, 0418
Rowa
Runco 0017, 0030
Ruyi 0817
Saba 0109, 0335, 0343
Sagem 0610
Saige 0009, 0817
Saisho 0009, 0264
Salora 0361
Sampo
Samsung
Sanjian 0264
Sansei 0451
Sansui 0463, 0706, 1935
Sanyo
Sanyuan 0009, 0093, 0817
SBR 0037
Sceptre 1217
Schaub Lorenz 0361
Schneider 0037, 0371, 0394
Scotch 0178
0030, 0047, 0056, 0154, 0178, 0180
0000, 0030, 0047, 0060, 0090, 0092, 0178, 0618, 0679, 1047, 1147, 1247, 1347, 1447, 1454, 1547
0030, 0056, 0154, 0178, 0180
0009, 0037, 0698, 0712, 0748, 0817
0009, 0030, 0092, 0093, 0154, 0171, 0178, 0474, 0650, 0700, 1755
0009, 0030, 0037, 0056, 0060, 0090, 0092, 0154, 0156, 0178, 0208, 0226, 0264, 0474, 0556, 0587, 0618, 0644, 0702, 0766, 0812, 0814, 0817, 1060, 1150
0088, 0145, 0154, 0156, 0180, 0208, 0264, 0376, 0424, 0474, 0508, 1150, 1179
TV
Scott 0178, 0180, 0236
0047, 0054, 0056,
Sears
SEG 0264, 1037, 1163
Semivox 0180
Semp 0156, 1356
Sentra 0035
Shancha 0264, 0817
Shanghai
Shaofeng 0145, 0817
Sharp
Shen Ying 0009, 0092, 0474
Shencai 0009, 0145, 0264
Sheng Chia
Shenyang
Sherwood 0009
Siemens 0037, 0195
Signet 1262
Simpson 0186
SKY 0037
Sky Brazil 0880
Skygiant 0180
Skyworth
Sliding 0865, 0880
Songba 0009
Sonitron 0208
Sonoko 0009, 0037
Sonolor 0208
Sontec 0037
Sony
Soundesign 0178, 0180, 0186
Soundwave 0037, 0418
Sowa
0154, 0156, 0171, 0178
0009, 0208, 0226, 0264, 0817
0009, 0030, 0093, 0256, 0474, 0650, 0787, 0818, 1165, 1193
0009, 0093, 0236, 0474, 1150
0009, 0264, 0753, 0817
0009, 0037, 0264, 0698, 0748, 0753, 0817
0000, 0650, 1100, 1167, 1300, 1505, 1651
0051, 0060, 0092, 0156, 0178, 0226, 0474, 1150
78
Remote Control Codes List—Continued
TV
Squareview 0171
SSS 0180
Standard 0009
Starlite 0180
Studio Experi­ence
Sunkai 0865
Superscan 0093, 0864
Supra 0056
Supreme 0000
Susumu 0474
SVA
Swisstec 0880
Sylvania
Symphonic 0171, 0180
Synco
Syntax 1144, 1240, 1331
Sysline 0037
T+A 0447
Ta c ic o
Tai Yi 0009, 1150
Taishan 0009, 0817
Tandy 0093
Tashiko 0092, 0650, 1150
Ta t un g
TCL 0698, 0706
TCM 0808
Teac
Technics 0051, 0250, 0650
Technisson 0714
Techview 0847
Techwood 0051, 0056, 1163
Te c o
Te k ni k a
Teleavia 0343
0843
0587, 0748, 0865, 0870, 0871
0030, 0054, 0171, 1314
0000, 0060, 0092, 0093, 0178, 0451, 0474
0009, 0092, 0178, 0474, 1150
0009, 0037, 0051, 0054, 0060, 0154, 0156, 0474, 1150, 1156, 1254, 1756
0009, 0037, 0264, 0418, 0455, 0698, 0706, 0712, 1037, 1755
0009, 0051, 0092, 0093, 0178, 0264, 0474, 0653
0054, 0056, 0060, 0092, 0150, 0180, 0186
TV
0056, 0074, 0109,
Telefunken
Teletech 0009
Teleton 0186
Tera 0030, 0092, 0474
Tevion 0767
Texla 0780
Thomson
Thorn
Thorn-Fergu­son
Tiane 0093, 0817
TMK 0056, 0178
TNCi 0017
Tobo 0009, 0264, 0748
Tongguang 0264
Tongtel 0780
Tophouse 0180
To s hi b a
TRANS-conti­nents
Transonic 0587, 0698, 0712
Tu n te x
TVS 0463
Universum
V7 Videoseven 1755
Vec to r Research
Vestel 0037
Victor
Videocon 0037, 0508
Vidikron 0054
Vidtech 0178
Viewsonic
Vizio 0864, 0885, 1756
Voxson 0178
0335, 0343, 0625, 0702, 0896
0109, 0343, 0560, 0625, 1447
0035, 0037, 0074, 0343, 0361, 0512
0343
0009, 0035, 0060, 0093, 0145, 0154, 0156, 0161, 0264, 0508, 0509, 0618, 0644, 0650, 0845, 1150, 1156, 1169, 1173, 1256, 1265, 1356, 1456, 1508, 1656, 1704, 1935
0865
0009, 0030, 0092, 0474
0037, 0074, 0264, 0346, 0474
0030
0053, 0160, 0250, 0376, 0650, 0653
0857, 0864, 0885, 1755
TV
Wards
Warumaia 0661
Watson 0037
Waycon 0156
Weipai 0009
Westinghouse 0885, 0889, 1282
White Westing­house
Xenius 0661
Xiahua
Xianghai 0009
Xiangyang 0264
Xiangyu 0009
Xihu 0264, 0817
Xingfu 0009
Xinghai 0264
Xoro 1217
Yamaha 0030
Yapshe 0250
Yingge 0009
Yoko 0037, 0264
Yonggu 0009
Youlanasi 0817
Yousida 0009
Yuhang 0009
Zenith
ZhuHai 0009
Zonda 0698
TV/DVD Combination
Akai 1935
Broksonic 1935
Bush 0698, 1037
Citizen 1935
Denver 0587
Grundig 1935
Sansui 1935
Toshiba 1935
Transonic 0587
0030, 0054, 0056, 0178, 0866, 1156
0037, 0186, 0463, 0623
0009, 0264, 0698, 0773, 0817
0017, 0092, 0178, 0463, 1265
79
*Memo
Integra Division of
ONKYO U.S.A. CORPORATION
18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.integrahometheater.com
Integra Division of
ONKYO CORPORATION
Sales & Product Planning Div.: 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8023 Fax: 072-831-8124
SN 29344561
(C) Copyright 2007 ONKYO CORPORATION Japan. All rights reserved.
80
E
Y0710-1
* 2 9 3 4 4 5 6 1 *
n
Loading...