IDEAL 61-610 User Manual
Page 1
#61-610
Analog Multimeter
Instruction Manual
WARNING
Read First: Safety Information
Please read and follow operating instructions
carefully. Misuse or abuse of this multimeter
cannot be prevented by any printed word. Use the
meter only as specified in this manual; otherwise,
the protection provided by the meter may be
impaired.
WARNING
To avoid possible electric shock or personal injury, follow these guidelines:
• Do not use if meter appears damaged. Visually inspect the meter to ensure
case is not cracked and back case is securely in place.
• Inspect and replace leads if insulation is damaged, metal is exposed, or probes
are cracked. Pay particular attention to the insulation surrounding the
connectors.
• Do not use meter if it operates abnormally as protection maybe impaired.
• Do not use during electrical storms or in wet weather.
• Do not use around explosive gas, dust, or vapor.
• Do not apply more than the rated voltage to the meter.
• Do not use without the battery and the back case properly installed.
ND 1722-3 61-610 INSTRUCTONS 1/9/07 9:47 AM Page 1
Page 2
• Before each use:
- Zero out the test leads in the resistance mode to verify the functionality of
the battery and test leads.
- Verify meter operation by measuring a known voltage. Apply meter to
circuit under test. And, test on a known live voltage again to ensure
proper operation.
• Remove test leads from input jacks prior to removing back of case.
• Only replace the fuse with specified volt, amp, and rupture speed ratings.
CAUTION
To protect yourself, think "Safety First":
• Voltages exceeding 30VAC or 60VDC pose a shock hazard so use caution.
• Use appropriate personal protective equipment such as safety glasses, face
shields, insulating gloves, insulating boots, and/or insulating mats.
• Use the 3 Point Safety Method.
• Never ground yourself when taking electrical measurements.
• Connect the black common lead to ground before applying the red test lead to
voltage. Disconnect the red test lead from the voltage first.
• Always work with a partner.
• When using the probes, keep fingers as far behind the probe tips as possible.
• Do not expose meter to mechanical shock, vibration, extreme temperature, or
strong magnetic fields.
Features:
• Measures AC/DC Voltage, DC Current, Resistance, and Battery Check
• Mirrored scale to reduce parallax error
• Fuse protected
• Diode protected meter movement
• Pocket-sized, lightweight, high-impact thermoplastic case
• Recessed input terminals for added safety.
ND 1722-3 61-610 INSTRUCTONS 1/9/07 9:47 AM Page 2
Page 3
WARNING: Before taking any measurements, always carefully set the
rotary switch to the highest range in the measurement function desired and then
switch to lower ranges until the pointer reads in the upper half of the scale.
MEASUREMENT PROCEDURE:
This high quality analog multimeter provides a long field life by following the
steps outlined below:
• Best Accuracy
- Ensure that the pointer is set exactly on the zero line located at the left
end of the arc using the Zero Dial. Note that changes in atmospheric
conditions can cause the pointer to drift daily.
- The pointer should read in the upper half of the scale, preferably in the
fourth quarter of the arc.
• Switch position
1) Prior to use, set the switch position to the highest range of the function
to be measured.
2) Adjust the switch down to lower successive ranges in this function until
the pointer reads in the upper half of the scale.
By using this method routinely, the meter is protected against overloads that may
"peg the needle" and cause damage to the pointer, particularly in cases where
circuit values are not known.
WARNING: When finished with taking measurements of one function,
remove the test leads completely from the circuit, before switching to another
function and repeating the measurement procedure above.
To Measure AC Voltage:
• Set the rotary switch to the highest range (500) in the ACV function.
• Insert the red test lead fully into the + input jack on the meter and fully seat the
black test lead into the – input jack on the meter.
• Hold the test leads behind the finger guards and apply the lead tips in
parallel to the circuit under test.
ND 1722-3 61-610 INSTRUCTONS 1/9/07 9:47 AM Page 3
Page 4
• Follow the MEASUREMENT PROCEDURE on page 4 to maximize accuracy and
prevent over-ranging of the pointer.
• Read the AC voltage measurement using the AC V labeled red arc (third arc
from the top).
CAUTION: For maximum safety, do not hold the meter in your
hands while measuring higher voltages using the 250 and
500 ACV ranges.
To Measure DC Voltage:
• Set the rotary switch to the highest range (500) in the DCV function.
• Insert the red test lead fully into the + input jack on the meter and fully seat the
black test lead into the – input jack on the meter.
• Hold the test leads behind the finger guards and apply the lead tips in
parallel to the circuit under test.
• Follow the MEASUREMENT PROCEDURE on page 4 to maximize accuracy and
prevent over-ranging of the pointer.
• Read the DC voltage measurement using the DC labeled black arc (second arc
from the top).
CAUTION: For maximum safety, do not hold the meter in your
hands while measuring higher voltages using the 250 and
500 DCV ranges.
CAUTION: Discharge all capacitors and inductors before taking
current measurements.
To Measure DC milli-amps:
• Set the rotary switch to the 250m range in the DCA function.
• Insert the red test lead fully into the + input jack on the meter and fully seat the
black test lead into the – input jack on the meter.
• Hold the test leads behind the finger guards and apply the lead tips in series
with the circuit under test.
ND 1722-3 61-610 INSTRUCTONS 1/9/07 9:47 AM Page 4
Page 5
• Follow the MEASUREMENT PROCEDURE on page 4 to maximize accuracy.
• Read the DC mA measurement using the mA labeled black arc (second arc
from the top).
WARNING: Verify that the circuit is completely de-energized
(dead) by measuring the circuit voltage to ensure that zero volts
(AC/DC) is present before taking any resistance measurements.
Exposing live voltage to the Ohms circuit by misuse or abuse may
result in injury to the operator and damage to the meter and equipment under test. The extent of injury and damage will depend on
the level of voltage and current in the circuit.
To Measure Resistance (Ohms):
• Verify the circuit is completely de-energized.
• Set the rotary switch to the highest range (Rx100) in the OHM function.
• Insert the red test lead fully into the + input jack on the meter and fully seat the
black test lead into the – input jack on the meter.
• Short the red and black test lead tips together and adjust the Zero Dial until
the pointer is directly over the zero position on the right end of the Ω labeled
green arc (top arc on the display).
Note: If the pointer cannot be zeroed, then the battery should be replaced.
• Apply the test leads to the component or dead circuit under test.
• Follow the MEASUREMENT PROCEDURE on page 4 to maximize accuracy.
• Read the ohms measurement using the Ω labeled green arc (top arc on the
display).
To Perform a Battery Check:
• Set the rotary switch to the 1.5V or 9V range on the B.TEST function.
• Insert the red test lead fully into the + input jack on the meter and fully seat the
black test lead into the – input jack on the meter.
• Apply the red test lead tip to the positive (+) battery contact and the black test
lead tip to the negative (-) battery contact.
ND 1722-3 61-610 INSTRUCTONS 1/9/07 9:47 AM Page 5
Page 6
• Follow the MEASUREMENT PROCEDURE on page 4 to maximize accuracy.
• Read the pointer position on the Bat labeled arc at the bottom of the display to
determine if the battery is Good or needs to be Replaced.
Note: The meter may not be able to check some 1.5VDC button cell batteries.
To Measure Decibels (dB):
• Set the rotary switch to the 10 range in the ACV function.
• Insert the red test lead fully into the + input jack on the meter and fully seat the
black test lead into the – input jack on the meter.
• Hold the test leads behind the finger guards and apply the lead tips to the circuit under test.
• Follow the MEASUREMENT PROCEDURE on page 4 to maximize accuracy and
prevent over-ranging of the pointer.
• Read the decibels measurement using the dB labeled red arc (fourth arc from
the top).
• For measurements above the basic dB range, set the switch to next highest
range on the ACV function and add dB correction as shown on the table in
the lower right of the scale plate on the meter.
Note: To remove the DC components in the circuit under test, connect a 0.1µF
capacitor, or larger, in series with one of the test leads before testing decibels.
MAINTENANCE
Battery Replacement:
• Remove test leads from meter.
• Remove the screw from the back of the case.
• Remove the back of the case.
• Replace battery with a 1.5V AA type battery.
• Assemble the back case on the meter and retighten the screw.
ND 1722-3 61-610 INSTRUCTONS 1/9/07 9:47 AM Page 6
Fuse Replacement:
• Remove test leads from meter.
• Remove the screw from the back of the case.
• Remove the back of the case.
• Replace fuse with same fuse type, size, and ratings (IDEAL #F-16).
• Assemble the back case on the meter and re-tighten the screw.
Replacement test leads: IDEAL #TL-34.
Maintenance:
• Clean the case with a damp cloth and mild detergent. Do not use abrasives
or solvents.
Service, and Replacement Parts:
For replacement parts or to inquire about service information contact IDEAL
INDUSTRIES, INC. at 1-877-201-9005 or visit our website
www.testersandmeters.com.
Specifications:
Sensitivity: 2kΩ/V AC/DC
Fuse: (1) 0.25A, 250V, 5mm x 20mm, fast-acting fuse
(IDEAL #F-16)
Battery: (1) 1.5V AA type battery.
Operating: 32 F to 122 F (0 C to 50 C)
Environment Maximum Relative Humidity <80% @ 31 C /
Minimum 50% @ 40 C
Altitude: 6561.7 ft. (2000m)
Dimensions: 4"H x2.9"W x0.9"D (100mm H x63mm W x34mm D)
Weight: 3.6 oz (102g)
Safety: Cat II-500V
Accessories Test Leads (#TL-34), (1) 1.5V AA type battery, operating
included: instructions.
Page 7
ND 1722-3 61-610 INSTRUCTONS 1/9/07 9:47 AM Page 7
Ranges & Accuracies:
AC Voltage: 10/50/250/500 ACV +/-4% FS
DC Voltage: 10/50/250/500 DCV +/-3% FS
DC Current: 250 mADC +/-4% FS
Resistance: 5/50/500 Ω Mid-scale +/-3% of Arc Length
1k/10k/100k Ω Full-scale +/-3% of Arc Length
Decibels: -20 to +56 dB on ACV ranges
Battery Check: 1.5V / 9V ranges
Double Insulation
Instrument has been evaluated and complies with insulation category II (overvoltage category II). Pollution degree 2 in accordance with IEC-644. Indoor use.
Warranty Statement:
This tester is warranted to the original purchaser against defects in material and workmanship for five years. During this warranty period, IDEAL INDUSTRIES, INC. will,
at it’s option, replace or repair the defective unit, subject to verification of the defect
or malfunction. This warranty does not apply to defects resulting from abuse, neglect,
accident, unauthorized repair, alteration, or unreasonable use of the instrument.
Any implied warranties arising out of the sale of an IDEAL product, including but not
limited to implied warranties of merchantability and fitness for a particular purpose,
are limited to the above. The manufacturer shall not be liable for loss of use of the
instrument or other incidental or consequential damages, expenses, or economic
loss, or for any claim or claims for such damage, expenses or economic loss.
State laws vary, so the above limitations or exclusions mat not apply to you. This
warranty gives you specific legal rights, and you may also have other rights which
vary form state to state.
Page 8
ND 1722-3 61-610 INSTRUCTONS 1/9/07 9:47 AM Page 8
Page 9
#61-610
Multímetro analógico
Manual de Instrucciones
ADVERTENCIA
Lea primero: Información de seguridad
Por favor, lea y siga cuidadosamente las i
nstrucciones de operación. Ninguna palabra
impresa puede prevenir el mal uso o abuso de
este multímetro. Utilice el medidor sólo según
se especifica en este manual; de lo contrario, la
protección que él proporciona podría deteriorarse.
ADVERTENCIA
• Siga estas instrucciones para evitar una posible descarga eléctrica o lesiones
personales:
• No utilice el medidor si se lo ve dañado. Inspeccione visualmente el medidor
para asegurarse de que la caja no esté agrietada y la caja posterior esté colocada firmemente.
• Inspeccione y reemplace los cables si el aislamiento está dañado, el metal
está al descubierto o las sondas están agrietadas. Preste atención en particular
al aislamiento que rodea los conectores.
• No utilice el medidor si funciona de forma anormal, ya que la protección
puede haberse dañado.
• No lo utilice durante tormentas eléctricas o con tiempo húmedo.
• No lo utilice cerca de gases, polvo o vapores explosivos.
• No aplique al medidor un voltaje mayor que el voltaje nominal.
ND 1722-3 61-610 INSTRUCTONS 1/9/07 9:47 AM Page 9
Loading...