Hustler 302638 User Manual

•••••••

Hustler Turf Equipment

•••••

P.O. Box 7000

•••

Hesston, Kansas

•

67062-2097

Hustler Mini Z

Super Mini Z

Owner’s Manual

302638 Rev 1/05

The engine exhaust from this product

contains chemicals known to the State

of California to cause cancer, birth

defects or other reproductive harm.

WARNING:

302638 Rev 1/05

TABLE OF CONTENTS

1. General Information.............................................................Sect. 1

2. Safety Precautions................................................................Sect. 2

3. Operation..............................................................................Sect. 3

4. Maintenance .........................................................................Sect. 4

5. Adjustments .........................................................................Sect. 5

6. Troubleshooting ...................................................................Sect. 6

7. Storage .................................................................................Sect. 7

8. Product Literature ................................................................Sect. 8

9. Technical Specifications ......................................................Sect. 9

10. Index...................................................................................Sect. 10

302638 Rev 1/05
302638 Rev 1/05

1-1

This manual applies to the following equipment:

Mini Z, 19/44", number 927228
Mini Z, 19/52”, number 927236
Mini Z, 24/52”, number 927251
Mini Z, 23/52”, number 927244
Super Mini Z, 23/44”, number 927269
Super Mini Z, 24/52”, number 927285
Super Mini Z, 25/52”, number 927277

To the new owner

The purpose of this manual is to assist owners and
operators in maintaining and operating the Mini Z and Super
Mini Z tractors and decks. Please read it carefully;
information and instructions furnished can help you achieve
years of dependable performance.

A separate Engine Manual is included with your owner’s
packet which contains additional engine information that
will not be repeated in this manual. You are urged to read it
before attempting any operation or repair of the engine.

The Quick Reference Decals, located under the right front
of the seat, the right front of the deck, and under the seat
pan, are designed to give the operator brief information
needed in the daily operation of the machine. These decals
are not intended to be used in place of this manual but
instead is to be used as an extension of this manual. These
decals should not be removed or obliterated. Replace these
decals if they become unreadable.

It is the owner’s responsibility to make certain that the
operator reads and understands this manual and the Quick
Reference Decals before operating this machine. It is also
the owner’s responsibility to make certain that the operator
is a qualified and physically able individual, properly
trained in the operation of this equipment. Local regulations
may restrict the age of the operator.

Using this manual

General operation, adjustment and maintenance guidance
is outlined for both the experienced and novice Hustler user.
Operating conditions vary considerably and cannot all be
addressed individually. Through experience, however,
operators should find no difficulty in developing good
operating skills suitable to most conditions.

Directions used in this manual, for example RIGHT or
LEFT, refer to directions when seated on tractor facing
forward, unless otherwise stated.

Photographs and illustrations used were current at the
time of printing, but subsequent production changes may
cause your machine to vary slightly in detail. Hustler Turf
Equipment reserves the right to redesign and change the
machine as deemed necessary, without notification. If a
change has been made to your machine which is not
reflected in this owner’s manual, or the parts manual, see
your Hustler dealer for current information and parts.

Warranty registration

The Delivery and Warranty Registration form must be
completed and signed to validate your warranty protection.
As the new equipment owner, you are expected to see that
the form is completed and forwarded to Hustler Turf
Equipment at time of delivery.

Be sure to register the tractor plus each attachment that
displays a model and serial identification number plate with
Hustler Turf Equipment.

IMPORTANT: Any unauthorized modification,
alteration, or use of non-approved attachments voids the
warranty and releases Hustler Turf Equipment from any
liability arising from subsequent use of this equipment.

Model and serial number

Tractor model and serial numbers are found on the serial
identification plate, located on the frame directly below and
to the left of the operator’s platform.

These numbers are required on the Warranty Registration
form. They will also assure you of the correct service parts
when replacement becomes necessary.

Parts and service

Use original Hustler replacement parts only. These parts
are available through your local Hustler dealer. To obtain
prompt, efficient service, always provide the following
information when ordering parts:

1. Correct part description

2. Correct model number.

3. Correct serial number.

All warranty repair and service must be handled through
an authorized Hustler dealer. Arrangements should be made
through your local service center.

For location of nearest dealer, or should you need further
assistance, contact:

Customer Service Department
Hustler Turf Equipment
P.O. Box 7000
Hesston, KS 67062
Telephone [phone]
FAX [phone]
Web site: www.hustlerturfequipment.com

GENERAL INFORMATION

302638 Rev 1/05

1-2

MINI Z AND SUPER MINI Z TWO YEAR LIMITED WARRANTY

FOR TRACTORS AND DECKS

(THREE YEAR LIMITED WARRANTY ON DECK

SPINDLE BEARING & DECK GAUGE FORK BEARING)

WHAT IS COVERED BY THIS WARRANTY

Hustler Turf Equipment, makes the following warranty to
the original purchaser only:

a. First and Second Year: Hustler Turf Equipment

Tractors and Power Units are warranted for two (2)
years from date of delivery on all materials and
workmanship.
If the Purchaser discovers within this warranty period a
defect in materials or workmanship:

● He must promptly notify Hustler Turf Equipment, or

an authorized dealer, in writing of the defect. In no
event shall such notification be received by Hustler
Turf Equipment, or an authorized dealer later than
twenty-five (25) months from date of delivery.

● Within a reasonable time after such notification,

Hustler Turf Equipment, will correct any defect in
material or workmanship on the Hustler Turf
Equipment, by repairing or replacing part(s) with
either new or used replacement parts.

● Such repair, including parts and labor shall be at the

expense of Hustler Turf Equipment, and,

b. Third Year: At the conclusion of the two year limited

warranty described in paragraph (a) above, there shall
be an additional one year limited warranty on deck
gauge fork bearings and deck spindle bearings only, no

labor.

If the Purchaser discovers within this warranty period a
defect in either of these bearings:

● He must promptly notify Hustler Turf Equipment, or

an authorized dealer, in writing of the defect. In no
event shall such notification be received by Hustler
Turf Equipment, or an authorized dealer later than
thirty-seven (37) months from date of delivery.

● Within a reasonable time after such notification,

Hustler Turf Equipment, will provide new
replacement bearing to install on the Hustler Turf
Equipment.

● The installation of the deck gauge fork bearing and

deck spindle bearing shall be at the expense of the
owner, and,

c. Rental Units (90 days): Within 90 days of date of

delivery Hustler Turf Equipment, provides a limited
warranty on all materials and workmanship for units
used for rental purposes.
If the Purchaser discovers within this warranty period a
defect in materials or workmanship:

● He must promptly notify Hustler Turf Equipment, or

an authorized dealer, in writing of the defect. In no
event shall such notification be received by Hustler
Turf Equipment, or an authorized dealer later than
120 days from date of delivery.

● Within a reasonable time after such notification,

Hustler Turf Equipment, will correct any defect in

material or workmanship on the Hustler Turf
Equipment, by repairing or replacing part(s) with
either new or used replacement parts.

● Such repair, including parts and labor shall be at the

expense of Hustler Turf Equipment, and,

d. Hustler Turf Equipment provides a limited warranty

for the entire length of ownership by the original
purchaser for the following items:

● Against all defects in the frame resulting from frame

breakage.

● Against all defects in the mowing deck which results

in the front edge of the deck being bent into the the
blades.

● Against hydraulic hose and fitting leaks.

If the original Purchaser discovers within this warranty
period such a defect:

● He must promptly notify Hustler Turf Equipment or

an authorized dealer, in writing of the defect. Such
notification must be received by Hustler Turf
Equipment or an authorized dealer during the period
when the equipment is owned by the original
purchaser.

● Hustler Turf Equipment will correct any defect in the

frame resulting in frame breakage by repairing or
replacing part(s) with new or used replacement parts.

● Hustler Turf Equipment will correct any defect in the

deck resulting in the front edge of the deck being
bent into the blades by repairing or replacing part(s)
with either new or used replacement parts.

● Such repair, including parts and labor, shall be at the

expense of Hustler Turf Equipment, and,

e. The engines are covered by a two (2) year limited

warranty, by the engine manufacturer, to the original
owner (commercial or residential) only except the
Caterpillar diesel engine which is covered by a three
(3) year limited warranty, and,

f. The battery is covered by a one (1) year limited

warranty to the original owner only.

WHO MUST PERFORM THE WARRANTY SERVICE

All warranty service will be performed by dealers authorized
by Hustler Turf Equipment. Service calls and/or
transportation expense of the product to and from the
authorized dealer, for warranty work, will be paid by the
owner of the product. For warranty service you can contact
an authorized dealer or write Hustler Turf Equipment, 200
South Ridge Road, Hesston, Kansas 67062, or call 1-620­327-4911.

WHAT IS NOT COVERED BY THIS WARRANTY

Hustler Turf Equipment, does not warranty:

● Some product, components or parts not

manufactured by Hustler Turf Equipment

302638 Rev 1/05

1-3

● Repairs made by unauthorized persons

● Damage caused by use of the Hustler Turf

Equipment for purposes other than those for which it
was designed

● Damages caused by disasters such as fire, flood,

wind, and lightening

● Damages caused by neglect, abuse, abnormal use,

improper or unreasonable use, accident, negligence
or misuse

● Repairs or replacement resulting from the use of

unauthorized parts, accessories or attachments

● Repairs or replacement as the result if any alterations

or modifications, in the determination of Hustler
Turf Equipment, which adversely affects the
operation, performance or durability of the
equipment.

● Hustler Turf Equipment which has the serial number

removed or made illegible

● Depreciation or damage caused by normal wear, lack

of reasonable and proper maintenance, failure to
follow the product’s owner’s manual operating,
maintenance and adjustment instructions or other
operational instructions provided by Hustler Turf
Equipment.

● Normal maintenance parts and service including, but

not limited to, filters, fuel, lubricants, tune-up parts,
belts, blades, blade sharpening, bearings, brake or
steering adjustments

● Repairs necessary due to improper fuel,

contaminates in the fuel system, or failure to
properly prepare the fuel system prior to any period
of non-use over three months

DISCLAIMER OF WARRANTY

The foregoing warranties are in lieu of all other
warranties, expressed or implied, including but not
limited to the implied warranties of merchantability and
fitness for a particular purpose. However, if the Hustler
Turf Equipment is purchased as a consumer product,
any implied warranty of merchantability or fitness for a
particular purpose is limited to the duration of this
limited warranty. Some states do not allow limitations
on how long an implied warranty lasts, so the above
limitation may not apply to you. This warranty gives
you specific legal rights, and you may also have other
rights which vary from state to state.

LIMITATION OF REMEDIES

In no case shall Hustler Turf Equipment, be liable for any
special, incidental, or consequential damages based upon
breach of warranty, breach of contract, negligence, strict
liability in tort, or any other legal theory.
Such damages include, but are not limited to:

● Loss of profits

● Loss of savings or revenue

● Loss of use of Hustler Turf Equipment or any

associated equipment

● Cost of capital

● Cost of any substitute equipment, facilities, services

or downtime

● The claims of third parties including customers, and

injury to property
Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation
or exclusion may not apply to you.

TIME LIMIT

Any action for breach of warranty must be commenced
within twenty-five (25) months following delivery of the
goods in a non-rental application. Any action for breach of
warranty must be commenced within 120 days following
delivery of the goods in a rental application.

NO OTHER WARRANTIES

Unless modified in writing, signed by both parties, and
approved by the President of Hustler Turf Equipment, this
agreement is understood to be the complete and exclusive
agreement between the parties, superseding all prior
agreements, oral or written, and all other communications
between the parties relating to the subject matter of this
agreement. No employee of Hustler Turf Equipment, or any
other party is authorized to make any warranty in addition to
those made in this agreement.

ALLOCATION OF RISKS

This agreement allocates the risks of product failure
between Hustler Turf Equipment, and the purchaser. This
allocation is recognized by both parties and is reflected in
the price of the goods.

OWNER'S RESPONSIBILITY

You must maintain your Hustler Turf Equipment product
following the maintenance procedures described in your
owner's manual. Such routine maintenance, whether
performed by a dealer or by you, is at your expense.

This machine like any other powered equipment is
potentially dangerous unless properly operated. Any

operator must be cautious and keep safety in mind at all
times. Any operator, prior to using the Hustler Turf
Equipment, should thoroughly familiarize himself with the
owner's manual regarding operation and safety of the
machine, as well as all safety warnings on the machine
itself.

WARRANTY REGISTRATION

1. The Warranty registration form MUST be completed
and signed by the authorized dealer and original
purchaser.

2. For validation, the completed Warranty registration
form MUST be forwarded to Hustler Turf Equipment,
within ten (10) days following date of purchase.

3. The date of purchase constitutes delivery.

302638 Rev 1/05

1-4

302638 Rev 1/05

2-1

This safety alert symbol is used to call attention to a
message intended to provide a reasonable degree of
PERSONAL SAFETY for operators and other persons
during the normal operation and servicing of this equipment.

DANGER – denotes immediate hazards which WILL
result in severe personal injury or death.

WARNING - denotes a hazard or unsafe practice which
COULD result in severe personal injury or death.

This manual uses two other words to highlight
information. IMPORTANT calls attention to special
mechanical information and NOTE: emphasizes general
information worthy of special attention.

All operators should read this manual, or be instructed
about safe operating and maintenance procedures. This is
the owner’s responsibility.

Improper use or maintenance by the operator or
owner can result in injury. To reduce the potential for
injury, comply with these safety instructions and always
pay attention to the safety alert ▲ symbol, which means
DANGER or WARNING - “personal safety
instructions.” Failure to comply with the instructions
may result in personal injury or death.

Incorrect usage of this machine may result in severe
injury. Personnel operating and maintaining it should
be trained in the proper use and should read the
manuals completely and thoroughly before attempting to
set-up, operate, adjust, or service this machine.

The Quick Reference Decals, located in front of and to the
right of the seat, are designed to give the operator brief
information needed in the daily operation and service of the
machine. These decals are not intended to be used in place
of this manual but instead is to be used as an extension of
this manual. These decals should not be removed or
obliterated. Replace these decals if they become
unreadable.

It is the owner’s responsibility to make certain that the
operator reads and understands this manual and all decals
before operating this machine. It is also the owner’s
responsibility to make certain that the operator is a
qualified and physically able individual, properly trained in
the operation of this equipment. Local regulations may
restrict the age of the operator.

The owner should also ensure that the operator/mechanic
know that they are responsible for their own safety as well
as the safety of other persons within the vicinity.
Remember, the operator is responsible for accidents or
hazards occurring to other people or their property.

Safe Operating Practices

Some of the following safety instructions are from ANSI
Standard B-71.4-1999 while others are specific to the
Hustler Mini Z and Super Mini Z units.

This product is capable of amputating hands and feet and
throwing objects. Always follow all safety instructions to
avoid serious injury or death.

Operation

▲

Never leave a running machine unattended. Always
disengage deck clutch, place control levers in park
brake position, stop tractor engine, and remove
ignition key when leaving operator’s seat.

▲

If you lose steering control while operating the
machine, place the steering control levers in the
park brake position immediately. Inspect the
machine and involve your Hustler dealer to resolve
the problem before continuing to operate.

▲

Always remain seated while operating machine.

▲

Always keep safety shields and covers in place, except
for servicing.

▲

Always maintain a safe distance from people and pets
when mowing. Always stop machine if someone
enters the area.

▲

Always operate machine in daylight or with adequate
working lights.

▲

Follow daily and weekly checklists, making sure hoses
are tightly secured and bolts are tightened.

▲

Always observe traffic laws while driving machine
from one location to another. Watch for traffic when
operating near or crossing roadways.

▲

Always keep engine and machine clean, removing
accumulated dirt, trash and other material from
machine. Clean up oil or fuel spillage. Allow
machine to cool before storing.

▲

Always be alert for hazards such as rocks, metal
objects and other debris which may be thrown or
entangled by mower blades. Watch out for holes or
deep depressions.

▲

Always inspect machine for damage after striking a
foreign object. If damage is found, repair machine
immediately. Be sure to disengage deck clutch, place
control levers in park brake position, stop tractor
engine, and remove ignition key when leaving
operator’s seat to inspect damage.

▲ Always wear adequate ear protection, such as

earplugs, when operating this equipment as prolonged
exposure to uncomfortable or loud noises can cause
impairment or loss of hearing. Do not wear radios or
music headphones while operating the machinery.
Safe operation requires your full attention.

▲

Always be aware of what is behind the machine before
backing up. Do not mow in reverse unless absolutely
necessary. Always look down and behind before and
while backing up.

SAFETY PRECAUTIONS

▲

Never push forward suddenly on the steering control
levers while the machine is in rearward motion
because the machine may tip backward.

▲

When moving in reverse, push forward slowly on lever
and avoid sudden movement. Rapid movement of the
control levers in either direction could result in a
reaction of the tractor that can cause serious injury.

▲

Never operate a poorly maintained machine.

▲

Never attempt high speed maneuvering, especially in
crowded or congested areas.

▲

Never allow persons to operate this machine without
proper instruction or allow children to operate
machine. Allow only responsible adults who are
familiar with these instructions to operate this
machine.

▲

Never put hands or feet under any part of the machine
while it is running.

▲

Never carry passengers.

▲

Never direct discharge of material from mower deck
towards bystanders. Do not operate the mower
without either the discharge chute or the entire grass
collection system in place.

▲

Always disengage the blades and wait for them to stop
before crossing gravel drives, walks or roads.

▲

Always keep clear of the mower blades and
attachments during their operation.

▲

Turn off blades when not mowing.

▲

Slow down before turning.

▲

Stop the engine before removing the grass catcher or
unclogging the discharge chute. Never clear the
discharge chute with the engine running. Turn off the
engine and be sure the blades have stopped before
cleaning. Use a stick to clear a plugged discharge area.

Never use your hand!

▲

Do not operate the machine while under the influence
of alcohol or drugs.

▲

Exercise caution when loading or unloading the
machine onto a trailer or truck.

▲

Always wear safety goggles or safety glasses with side
shields when operating the mower.

▲

Data indicates that operators, age 60 years and above,
are involved in a large percentage of riding mower­related injuries. These operators should evaluate their
ability to operate the mower safely enough to protect
themselves and others from serious injury.

▲

Never make sudden starts, stops, turns, or reverse
direction, especially when maneuvering on slopes.
The steering is designed for sensitive response. Rapid
movement of the control levers in either direction
could result in a reaction of the tractor that can cause
serious injury.

▲

If any attachment or additional weight is mounted on
the rear of the unit, any rapid movement of the control
levers in either direction could result in a reaction of
the tractor that can cause serious injury.

▲▲

Clean flammable material from machine. Prevent
fires by keeping engine compartment, battery, fuel
line, fuel tank and operator’s station clean of
accumulated trash, grass clippings, and other
debris. Always clean up spilled fuel and oil.

Slope Operation

Slopes are a major factor in loss-of-control and tip-over
accidents, which can result in sever injury or death. All
slopes require extra caution. If you cannot back up the
slope or if you feel uneasy on it; do not mow it.

▲

Use extreme caution when operating on slopes.

• Be extremely careful changing directions on a slope.
Slow down.

• Do not operate where the machine could slip or tip.

▲

Do not remove or modify the stabilizer wheels.

▲

Watch for holes, ruts or bumps. Uneven terrain could
overturn the machine. Tall grass can hide obstacles.

▲

Remove obstacles such as rocks, tree limbs, etc.

▲

Keep all movement on slopes slow and gradual. Do
not make sudden changes in speed or direction.

▲

Avoid starting and stopping on a slope. If tires lose
traction, disengage the blades and proceed slowly
straight down the slope.

▲

Do not turn on slopes unless necessary, and then, turn
slowly and gradually downhill, if possible.

▲

Do not mow near drop-offs, ditches, or embankments.
The machine could suddenly turn over if a wheel goes
over the edge of a cliff or ditch, or if an edge caves in.

▲

Do not mow on wet grass. Reduced traction could
cause sliding.

▲

Do not try to stabilize the machine by putting your foot
on the ground.

▲

The Hustler mower is capable of operating
horizontally (traverse) on moderately steep slopes.
When operating on slopes up to 15 degrees, be aware
of any conditions that may cause the tractor drive tires
to lose traction resulting in a possible loss of control of
the machine. An operator should not operate on a
slope until he is thoroughly familiar with the
equipment.

Do not operate the machine on slopes greater than
15 degrees.

Refer to Figure 2-1, page 2-5, when determining the
degree of slope to be mowed.

It is strongly recommended that the operator drive

the machine off of the slope, using extreme caution, if
any sign of loss of traction is detected. Wait until the
condition that caused the problem is resolved before
attempting to operate on the slope again.

Terrain conditions can affect traction resulting in

possible loss of control of the machine. Some of the
conditions to be aware of are:

1. Wet terrain

2. Depressions in the ground; i.e. holes, ruts,

washouts

3. Mounds of dirt

4. Soil type; i.e. sand, loose dirt, gravel, clay

5. Grass type, density, and height

6. Extremely dry conditions of grass

7. Tire pressure

The attachments mounted to the tractor will also

affect the way it handles on a slope. Be aware that
each attachment’s characteristics vary.

Another consideration to safe mowing on slopes is

to be aware of what is located at the bottom of the

302638 Rev 1/05

2-2

302638 Rev 1/05

2-3

slope. Extreme caution should be used when there is a
hazard located at the bottom of the slope. Some
examples are:

1. Water; i.e. lake, river

2. Cliffs, retaining walls

3. Roads, highways

4. Buildings

5. Rocks

These are just a few examples of situations when
caution must be used when operating on a slope.
There are many other possibilities too numerous to
mention. Just remember to always exercise extreme
caution when operating on any slope.

Children

Tragic accidents can occur if the operator is not alert to
the presence of children. Children are often attracted to
the machine and the mowing activity. Never assume that
children will remain where you last saw them.

▲

Never leave machine unattended with ignition key in
switch, especially with children present.

▲

Keep children out of the mowing area and under the
watchful care of another responsible adult.

▲

Be alert and turn the machine off if children enter the
area.

▲

Before and while backing, look behind and down for
small children.

▲

Never carry children, even with the blades off. They
may fall off and be seriously injured or interfere with
safe machine operation.

▲

Never allow children to operate the machine.

▲

Use care when approaching blind corners, shrubs,
trees, the end of a fence or other objects that may
obscure vision.

Service

▲

Always keep engine and machine clean, removing
accumulated dirt, trash and other material from
machine. Clean up oil or fuel spillage. Allow machine
to cool before storing.

▲

Always wear adequate eye protection when servicing
the battery or when grinding mower blades and
removing accumulated debris.

▲

Use extra caution when handling gasoline and other
fuels. They are flammable and vapors are explosive.

▲

Never refuel tractor while engine is running; never
refuel near an open flame or near devices which can
create a spark. Refuel outdoors preferably, or in well
ventilated areas.

▲

Never attempt to start engine when there is a strong
odor of gasoline fumes present. Locate and correct
cause.

▲

Never run the engine in an enclosed area unless
exhaust is vented to the outside. Exhaust gases contain
carbon monoxide which is odorless and deadly poison.

▲

Never attempt to make any adjustments or repairs to
the tractor drive system, mower deck or any
attachment while the tractor engine is running or deck
clutch is engaged. Repairs or maintenance requiring
engine power should be performed by trained
personnel only.

▲

Never work under the machine or attachment unless it
is safely supported with stands, blocks or a hoist.

▲

Do not touch hot parts of machine.

▲

Keep nuts and bolts tight, especially the blade
attachment bolts. Keep equipment in good condition.

▲

Never tamper with safety devices. Check their proper
operation regularly.

▲

Grass collection system components are subject to
wear, damage and deterioration, which could expose
moving parts or allow objects to be thrown.
Frequently check components and replace with
manufacturer’s recommended parts, when necessary.

▲

Mower blades are sharp and can cut. Wrap the
blade(s) or wear gloves and use extra caution when
servicing them.

▲

Use only genuine Hustler replacement parts to ensure
that original standards are maintained

Read Owner’s Manual and Quick

Reference Decal before attempting to

operate this machine.

Do not smoke while refueling.
Do not fill tank with engine running,
or while the engine is hot.
Allow engine to cool before storing
machine inside a building.
Store away from open flame or spark
if there is fuel in tank.
Clean up any gasoline spills.
Do not refuel while in enclosed trailer
or other enclosed areas

Safety and Instruction Decals

▲▲

Specific safety warning decals are located on the equipment near the immediate areas of potential hazards. These decals
should not be removed or obliterated. Replace them if they become non-readable.

The following illustrations show the various safety decals that are located on the machine. A brief explanation is shown
to help the operator understand the meanings of these decals.

Avoid skin contact with battery acid.
Always wear eye protection when
checking the battery, acid can cause
serious injury to skin and eyes. If
contact occurs, flush area with clean
water and call physician immediately.
Acid will also damage clothing.
Do not allow open flame near the
battery when charging.
Hydrogen gas forms inside the
battery. This gas is both toxic and
flammable and may cause an
explosion if exposed to flame.
Always remove the negative ground
first and replace it last.
Do not overfill battery.
Electrolyte may overflow and
damage paint, wiring or structure.
When cleaning the battery, use soap
and water. Be careful not to get
soap and water into the battery. Use
soda mixed in water to clean
corrosion off the terminals.

Hydraulic fluid escaping under
pressure can penetrate skin.
Hydraulic fluid may also cause
infection in a minor cut or opening in
the skin; if exposed to hydraulic fluid,
see a doctor at once.
Before applying pressure to hydraulic
system, make sure all connections
are tight and all hoses and lines are
in good condition.
Relieve all pressure in the system
before disconnecting or working on
hydraulic lines.
To find a leak under pressure, use a
piece of cardboard or wood – never
use your hands.
To relieve all pressure in system,
turn engine off and lower attachment.

Do not remove or modify stabilizer
wheels or rear engine guard or injury
can result.
Never stop suddenly while backing
down slopes. This action may result
in a reaction of the tractor that can
cause serious physical injury.

Never operate the mower deck with
side deflector removed or in raised
position, except when the grass
catcher attachment is being used.

Hot surface!

Keep shields or covers in place
while machine is in operation.
Keep hands away from rotating
pulleys and belts.

Whirling blades! Keep hands and
feet away.
Beware of thrown objects.

302638 Rev 1/05

2-4

1. Hold this sheet of paper in front of you. Make sure that line A is horizontal.

2. Align line B with a verticle surface such as a pole, tree or building.

3. Fold the paper along the slope guide lines (C, D or E).

4. Align the closest slope guide line with the ground slope. This will give you a close estimation of the
ground slope to be mowed.

Slope Guide Lines

C (5o)

D (10o)

E (15o)

Line A

Line B

SLOPE GUIDE

Figure 2-1

Use this diagram when determining the degree of slope to be mowed.

302638 Rev 1/05

2-5

302638 Rev 1/05

2-6

302638 Rev 1/05

3-1

OPERATION

Figure 3-1

IMPORTANT: When access is required under the seat

platform make certain to place the control arms in the
park brake position and pivot the arm rests upward
before placing the seat platform in the full forward
position to prevent arm rest damage.

Controls

For general location of the controls described in this

section, refer to Figure 3-1.

1. Ignition switch (Fig. 3-2) – a three position switch:

off, run, and start. With key inserted, rotate it
clockwise to START position; release key when
engine starts, and switch will automatically return to
the RUN position.

2. Throttle control (Fig. 3-2) — a cable is linked to
engine throttle for controlling engine speed. Move

lever forward to increase engine rpm, move lever
rearward to decrease engine rpm.

3. Choke control (Fig. 3-2) – a cable is linked to
manually operate the engine choke. When the lever is
in the down position, the choke is in the off (run)
position. When the lever is pulled up, the choke is in
the on (start) position. Do not operate the machine in
the on (start) position.

4. Control levers (Fig. 3-3) — these levers control the
tractor’s speed, direction, neutral lock, and park brake.
Levers are used to steer, accelerate, decelerate and
change direction. When the control levers are in the
park brake position (Fig. 3-4) the tractor will not move
when the engine is on and drive pumps are operating.

WARNING: The parking brake is not designed
to hold the tractor on steep slopes.

Figure 3-2

Figure 3-3

1. Ignition Switch 5. Deck lift pedal 9. Hydraulic reservoir 14. Left deck cover

2. Throttle lever 6. Hour meter 10. Battery 15. Right deck cover

3. Control levers 7. Oil Pressure light 11. Deck adjusting rod 16. Deck height indicator

4. Deck clutch switch 8. Fuel tanks 12. Anti-scalp wheels 17. Park brake switch

13. Discharge chute 18. Choke lever

IIggnniittiioonn

sswwiittcchh

TThhrroottttllee

Deck clutch

switch

Control

lever

Mini Z Controls

11

1

8

14

4

2

6

13

15

9

12

5

7

10

16

8

11

12

12

3

12

12

OOiill pprreessssuurree lliigghhtt

17

17

CChhookkee

18

5. Deck clutch switch (Fig. 3-2) — this switch engages
the deck. Pull the switch up to engage and push switch
down to disengage the clutch.
IMPORTANT: Never engage clutch with engine
running at high rpm or when the deck is under load.
Clutch, belts or deck could be damaged.

6. Deck lift pedal (Fig. 3-5) — the deck lift pedal is used
to raise or lower the deck. Push on the pedal to raise
the deck and then place the deck height locking pin
into the desired cutting height hole.
Push the deck lift pedal to raise the deck when going
over obstructions.

Instrumentation

7. Electronic hour meter (Fig. 3-6) — registers 1/10
hour increments up to 9,999.9 total hours. Connected
to the ignition switch, the meter records the
accumulative time while the ignition key is switched to
the RUN position and the operator is on the seat.

8. Oil pressure light (Fig. 3-2) — this light comes on
when the ignition switch is placed in the RUN position
and stays lit until the engine is running and a safe oil
pressure is developed. If light comes on during
operation, shut engine off immediately and locate and
correct the problem.

Safety interlock system

The tractor is equipped with a safety start interlock
system consisting of the park brake switches, seat switch,
and deck clutch switch.

Check tractor safety start interlock system daily, prior to
operation. This system is an important tractor safety feature.
It should be repaired immediately if it malfunctions. The
machine incorporates a separate seat switch which will stop
the tractor engine when the operator is unseated for any
reason while the tractor is operating. This is a safety feature
designed to prevent runaway or accidental entanglement. To
inspect the system:

1. The operator must be on the seat when testing the seat
switch.

2. Set both control levers in the park brake position.

3. Start the engine and allow it to warm up to operating

temperature.

4. With the deck clutch switch down and the control
levers in the park brake position, slowly raise off of the
seat. The engine should continue to run.

5. With the deck clutch switch up and/or the control
levers in the neutral position, slowly raise off of the
seat. The engine should stop.

6. If the engine fails to stop when the deck clutch switch
is up or one or both of the control levers is up and the
operator is off the seat, check the function of the seat
switch. If the seat switch is not operating properly (is
not opening or closing) and if the cause can not be
determined, replace the seat switch.

If the problem can not be located, contact your Hustler

Dealer.

WARNING: The safety interlock system should
always function per steps 4 and 5. If it does not
function properly, it should be corrected
immediately. Do not operate machine without
properly functioning seat safety switch.

Engine starting

The Mini Z safety start interlock system is also designed
to protect the operator and others from accidental injury due
to unintentional engine starting. The engine starting motor
will not engage until:

302638 Rev 1/05

3-2

Figure 3-5

Deck lift

pedal

Figure 3-6

Hour

meter

Figure 3-4

Control lever in park brake position

A. Control levers are in the park brake position.
B. Deck clutch switch is in the down (OFF) position.

WARNING: The safety interlock system must
not be disconnected or bypassed.

NOTE: The operator’s seat is equipped with a separate

safety switch. If for any reason the operator should become
unseated when the brake switches are disengaged or the
deck clutch switch is engaged the engine will stop.

The following steps are the correct procedures for
starting the engine. If difficulty is encountered, contact the
Hustler Dealer in your area.

1. Before starting tractor each day, perform daily pre­operation checking.

2. Make sure the control levers are in the park brake
position and deck clutch switch is disengaged.

3. Use choke when engine is cold, or if warm engine fails
to start within 5 seconds of cranking. Avoid flooding
and operate engine without choking as soon as
possible.

4. Set throttle at approximately 1/2 open position.

5. Insert key in ignition switch and rotate full clockwise

to engage starting motor. Release key when engine
starts.

IMPORTANT: The engine starter should not be

operated for periods longer than 30 seconds at a time. An
interval of at least two minutes should be allowed between
such cranking periods to protect the starter from overheating
and burn-out.

6. Perform test to make sure safety start interlock system
is operating properly. Refer to Safety start interlock
system section.

7. As soon as engine begins to run, check to make certain
the oil warning light is off. If not, stop engine
immediately and check for the cause.

8. Allow the engine to idle a few minutes before
advancing the throttle and/or engaging the deck clutch.

9. Before stopping the engine, place the control levers in
the park brake position, disengage the deck clutch, and
throttle back to low idle for a couple of minutes; then
rotate ignition key counter-clockwise to the OFF
position. Remove the key from switch before leaving
the tractor.

WARNING: Never leave the machine
unattended with key in ignition switch.

Moving tractor with stalled engine

If it becomes necessary to move the tractor when the
engine is inoperative, the hydraulic pumps are equipped with
bypass valves. Before moving the unit, turn bypass valves
counter clockwise one-half to one revolution. The valve
stems on each hydraulic pump are located near the top and
are identified as a hex stud. The valve is located per Figure
3-7.

Do not tow the machine. Move it by hand or use a winch
to load on a trailer for transporting.

When transporting on another vehicle, the tractor should

be facing forward and it must be secured.

IMPORTANT: Always make certain the two bypass

valves are returned to their operating position before running
the tractor following repairs.

Driving the tractor

DANGER: Never make sudden stops or reverse

direction, especially when going down a slope.
The steering is designed for sensitive response.
Rapid movement of the control levers in either
direction could result in a reaction of the tractor
that can cause serious injury.

After starting engine, engage the control levers

and steer as follows:

To go forward, push control levers forward an equal

distance (Fig. 3-8).

To go in reverse, pull control levers rearward an equal

distance (Fig. 3-8).

To turn left, move the right control lever farther forward

from neutral than the left control lever.(Fig. 3-8)

To turn right, move the left control lever farther forward

from neutral than the right control lever. (Fig. 3-8)

To pivot turn, move one control lever forward and the
other control lever back of neutral. This will allow the drive
wheels to counter-rotate. (Fig. 3-8)

To stop or decrease speed, move control levers to
neutral. When going forward pull back gently on control
levers. When going in reverse push forward gently on
control levers.

DANGER: When moving in the rearward
direction push forward gently on control levers
and avoid sudden movement. Any sudden
movement could cause the front of the mower to
come off of the ground resulting in possible loss
of control.

WARNING: Never stop suddenly while backing
down slopes. This action may result in a
reaction of the tractor that can cause serious
physical injury.

302638 Rev 1/05

3-3

Figure 3-7

Bypass valve

To increase speed, increase control lever’s distance from
neutral. The farther forward control levers are from neutral,
the faster tractor will travel forward. The farther back
control levers are from neutral, the faster tractor will go in
reverse.

Operating suggestions

DANGER: Prior to operating the tractor the

operator should be thoroughly familiar with the
proper use and operation of the equipment,
should read the manual completely and
thoroughly, and should have attempted slow
moving maneuvers to become familiar with the
operation of the equipment before attempting
normal speed operation. An inexperienced
operator should not mow on slopes or on uneven
terrain.

WARNING: If you lose steering control while
operating the machine, place the steering
control levers in the park brake position
immediately. Inspect the machine and involve
your Hustler dealer to resolve the problem
before continuing to operate.

WARNING: The unit’s control levers are very
responsive: Easy does it! For smooth operation,
move lever slowly, avoid sudden movement.
Skill and ease of operation come with practice
and experience.

Inexperienced operators may have a tendency to
oversteer and lose control. Slow-moving practice
maneuvers are recommended to become familiar with these
characteristics before attempting normal speed operation.

WARNING: Sharp depressions or raised
obstacles (such as gutters or curbs) should not be
directly approached at high speed in an attempt
to “jump” them as the operator could be thrown
from the equipment. Approach at a slow speed
and angle one drive wheel at the obstruction.
Continue at an angle until the wheel clears and
then pivot the opposite wheel around.

When turning on soft wet turf, keep both wheels rolling
either forward or backward. Pivoting on one stopped wheel
can damage turf. This is especially important when
mowing.

Tractor performance is maximum when the throttle is set
at full rpm. This gives maximum power to the drive wheels
and deck when needed. Use the control levers to control
ground speed rather than engine rpm.

WARNING: Do not operate the equipment
while wearing sandals, tennis shoes, sneakers,
shorts or any type of loose fitting clothing.
Always wear long pants, safety glasses and
safety shoes when operating this machine.

Keep blades sharp. Many professional mowing
companies have additional sets of blades and change blades
twice a day: once in the morning and again at noon. Many

problems with incorrect cutting patterns are due to dull
blades or blades which have been sharpened incorrectly.

Information on sharpening blades is listed in this manual’s
maintenance section. In addition, most communities have
individuals or companies which specialize in sharpening
mower blades. Blade sharpness should be checked daily.

Use high blade speed. Your Mini Z is designed to
operate at full throttle. The throttle setting directly controls
blade speed. The highest blade speed generally gives best
cut.

302638 Rev 1/05

3-4

FRONT OF TRACTOR FACES THIS DIRECTION

Figure 3-8

FORWARD TRAVEL PIVOT TURN REVERSE TRAVEL

RIGHT TURN

REVERSE TRAVEL

NN

FORWARD TRAVEL

RIGHT TURN

N = Neutral Position
Direction of arrows indicate direction of tractor movement.

Direct grass discharge to right, away from unmown

area. Select a mowing pattern that directs grass discharge

towards the outside, not towards center, of mowing area.
Generally, this means using a pattern utilizing left turns
because side discharge (Fig. 3-9) is to right. In any case,
avoid throwing grass discharge onto unmowed area because
grass is then mowed “twice”. Mowing twice puts an
unnecessary load on the unit and reduces mowing efficiency.

WARNING: Never direct discharge of material
from mower deck towards bystanders.

WARNING: Never operate the mower deck
with discharge chute removed or in raised
position.

WARNING: Always check area to be mown for
rocks and other debris before mowing.

Mower deck operation

DANGER: Never attempt to make any

adjustments to the mower deck while the engine
is running or with the deck drive clutch engaged.
Mower blades cannot be seen and are located
very close to deck housing. Fingers and toes can
be cut off instantly.

With the engine running, engage the deck clutch switch

(Fig. 3-2) and advance engine throttle to full rpm.

NOTE: Engaging the deck clutch at high engine rpm or

when under heavy load (in tall grass for example) can cause
belts and/or electric clutch to slip, resulting in premature
wear or possible damage.

302638 Rev 1/05

3-5

Figure 3-9

Side discharge chute

4-1

302638 Rev 1/05

MAINTENANCE

MAINTENANCE LOCATOR

CHART

1. Engine Oil Fill & Dipstick
2A. Fuel Filter (Kawasaki)
2B. Fuel Filter (Honda)

3. Engine Air Cleaner

4. Engine Oil Drain Plug

5. Battery

6. Fuel Tanks

7. Hydraulic Oil Reservoir

8. Deck Pusher Arm Zerks (2)

9. Hydraulic Oil Filter

10. Gauge Wheel Bearing Zerks (2)

11. Engine Oil Filter

12. Deck Height Pivot Zerks (4)

13. Park Brake Switch

14. Drive Tire

15. Pump Idler Zerk (1)

16. Deck Belt

17. Pump Belt

18. Blades

19. Hydraulic Oil Heat Exchanger

6

11

2A

4

3

12

16

10

12

10

5

13

7

1

6

13

12

12

Figure 4-1

18

18

8

8

16

19

2B

14

9

14

17

15

Viewed from bottom of tractor

NOTES:

1. Initial oil change is after 5 hours of operation. Thereafter, change oil after every 40

hours operation. Change more often under dusty or dirty conditions and during hot weather
periods.

2. Torque initially and after first 2 hours of operation.

3. Perform initial hydraulic filter change after 50 hours (one week) of operation.

4. Change engine oil filter per the engine manufacturer’s recommendations. Refer to

Engine Owner’s Manual for recommendations and other maintenance items.

5. Service more often under dusty or dirty conditions. Use caution when servicing to prevent
dust contamination in the engine. Do not clean filter element. Replace with a new one.

6. Pump drive belt only - Inspect every 100 hours and replace if worn or cracking is
noticed. Otherwise, replace every 400 hours or 2 years whichever comes first.

7. Check fuel line hoses, fuel valve and grommet for any cracks or leaks.
REFERENCES:
a — Refer to Engine Owner’s Manual

NOTE: After completing maintenance cycle (500

hours), repeat cycle.

Introduction

WARNING: Unless specifically required, DO

NOT have engine running when servicing or
making adjustments to tractor. Place control
levers in the park brake position, disengage deck
clutch, and remove ignition switch key. Repairs
or maintenance requiring engine power should be
performed by trained personnel only. To prevent
carbon monoxide poisoning, be sure proper
ventilation is available when engine must be
operated in an enclosed area. Read and observe
safety warnings in front of manual.

DANGER: Before working on or under the
deck, make certain engine cannot be accidentally
started. Shut engine off and remove ignition
switch key for maximum safety. Repairs or
maintenance requiring engine power should be
performed by trained personnel only.

DANGER: Exercise caution when working
under the deck as the mower blades are
extremely sharp. Wearing gloves is advisable
when working around or with the blades.

WARNING: Except when changing or checking
belt, always keep belt covers on mower for
safety as well as cleanliness.

WARNING: When possible clean under mower,
using a stick or similar instrument making sure
that no part of the body, especially arms and
hands are under mower.

Regular maintenance is the best prevention for costly
downtime or expensive, premature repair. The following
pages contain suggested maintenance information and
schedules which the operator should follow on a routine
basis.

Remain alert for unusual noises, they could be signaling
a problem. Visually inspect the machine for any abnormal
wear or damage. A good time to detect potential problems
is while performing scheduled maintenance service.
Correcting the problem as quickly as possible is the best
insurance.

WARNING: Keep your machine clean and
remove any deposits of trash and clippings,
which can cause engine fires and hydraulic
overheating as well as excessive belt wear.

Clear away heavy build-up of grease, oil and dirt,
especially in the engine and hydraulic reservoir area; minute
dust particle are abrasive to close-tolerance engine and
hydraulic assemblies.

Daily inspect mower for grass clippings and wire and
string tangles. The underside of the mower deck will collect
a build-up of grass clippings and dirt, especially when grass
is wet or has high moisture content. This build-up will
harden, restricting blade and air movement and will
probably show a poorer quality of cutting. Therefore it
should be removed routinely.

To do this it will be necessary to raise and block the deck
in the full up position and scrape the build-up from
underneath.

Some repairs require the assistance of a trained service
mechanic and should not be attempted by unskilled
personnel. Consult your Hustler service center when
assistance is needed.

Torque values

WARNING: Particular attention must be given

to tightening the drive wheel lug nuts, wheel
motor nuts, and blade spindle bolts. Failure to
correctly torque these items may result in the
loss of a wheel or blade, which can cause serious
damage or personal injury.

4-2

302638 Rev 1/05

WEEKLY MONTHLY ANNUALLY OR

SERVICE AT OR 50 OR 100 500

INTERVALS INDICATED HOURS HOURS HOURS

Verify safety start interlock system Daily
Visually inspect unit for loose
hardware and/or damaged parts Daily
Visually inspect tires Daily
Check oil level, engine (1) Daily or every 4 hrs.
Clean air intake screen (5) Daily or every 4 hrs.
Clean oil heat exchanger (5) Daily or every 4 hrs.
Check fuel level Daily
Blades - sharpen & securely fastened Daily
Discharge chute - securely in place &
in lowest position Daily
Clean engine and pump compartments Daily
Replace air cleaner paper element (5) As needed
Grease deck pusher arms x
Grease pump idler x
Grease deck height pivots x
Grease gauge wheel bearings x
Change engine oil & filter (1) (4) x
Clean cylinder and head fins (a) x
Check battery connections x
Check tire pressure with a gauge x
Check hydraulic oil level x
Clean engine exterior (a) x
Clean and regap spark plugs (a) x
Check pump and deck belt tension
& condition (6) x
Check fuel and hydraulic lines (7) x
Check fuel valve and grommet (7) x
Tighten lug nuts on wheels (2) x
Change fuel filter x
Clean or replace hydraulic fill cap x
Change hydraulic filter and oil (3) x
Replace spark plugs x

Torque values given below:

Ft-lbs. Nm

Wheel (lug) nuts ................................65-75......88.14-101.7

Wheel motor nut ...........................290-310 .....393.2-420.4

Blade spindle bolt top . . . . . . . . . . . .118.............160.01

Blade spindle bolt bottom . . . . . . . .118 .............160.01

It is recommended that these be checked after the first 2
hours of operation, initially and every 50 hours following
removal for repair or replacement.

For all other torques refer to the tractor parts manual for
standard torque chart.

For engine torque values, see engine owner’s manual.

Tires

It is important for level mowing that the tires have the
same amount of air pressure. The recommended pressure
are:

Drive wheels...............................................8-10 psi

Gauge wheels .............................................8-10 psi

Solid fill tires are not recommended for Hustler turf
equipment. On any machine, with solid filled tires, the
warranty claim will be denied.

Hour meter

To recognize when your machine needs servicing, check
the hour meter and the maintenance schedule. The hour
meter shows the number of hours the engine has run and the
maintenance schedule lists the service intervals. Fig. 4-2

Lubrication

1. Grease the front gauge wheel bearings per the
Maintenance Schedule. Use SAE multi-purpose
grease.

2. Grease the four deck lift pivots, located to the side of
the operator’s footrest per the Maintenance Schedule.
Use SAE multi-purpose grease.

3. Grease the pump idler per the Maintenance Schedule.
Use SAE multi-purpose grease.

4. Grease the two deck pusher arm pivots per the
Maintenance Schedule. Use SAE multi-purpose
grease.

Electrical system

The electrical system is a 12 volt, negative ground.
Recommended battery size is a garden tractor BCI group
U1R with 225 or better cranking AMP rating. A
maintenance-free battery is recommended. Otherwise,
follow battery manufacturer’s maintenance, safety, storing
and charging specifications.

The battery is located under the seat. Fig. 4-3

WARNING: Avoid skin contact with battery
acid.
Always wear eye protection when checking the
battery, acid can cause serious injury to skin and
eyes. If contact occurs, flush area with clean
water and call physician immediately. Acid will
also damage clothing.
Do not allow open flame near the battery when
charging.
Hydrogen gas forms inside the battery. This gas
is both toxic and flammable and may cause an
explosion if exposed to flame. Always remove
the negative ground first and replace it last.
Do not overfill battery.
Electrolyte may overflow and damage paint,
wiring or structure. When cleaning the battery,
use soap and water. Be careful not to get soap
and water into the battery. Use soda mixed in
water to clean corrosion off the terminals.

Common circuit failures are usually caused by shorting,
corroded or dirty terminals; loose connections, defective
wire insulation or broken wires. Switches, solenoids and
ignition components may also fail, causing a shorted or open
circuit.

Before attempting any failure diagnosis of the electrical
system, use a test light or voltmeter to check the battery
voltage. If the battery voltage is satisfactory, check the
cleanliness and tightness of the terminals and ground
connections. A general understanding of electrical servicing
and use of basic test equipment is necessary for
troubleshooting and repair.

302638 Rev 1/05

4-3

Figure 4-3

Battery

Figure 4-2

Hour

meter

4-4

302638 Rev 1/05

Wiring Schematic

Hustler Mini Z

Model Numbers 927228 (Kawasaki 19 hp) and 927244 (Kawasaki 23 hp)

302638 Rev 1/05

4-5

Wiring Schematic

Hustler Super Mini Z

Model Numbers 927269 (Kawasaki 23 hp) and 927277 (Kawasaki 25 hp)

4-6

302638 Rev 1/05

Wiring Schematic

Hustler Mini Z

Model Numbers 927236 (Honda 24 hp) and 927251 (Honda 24 hp)

302638 Rev 1/05

4-7

Wiring Schematic

Hustler Super Mini Z

Model Number 927285 (Honda 24 hp)

Major overhaul or repair of the starting motor or

alternator should be performed by trained technicians only.

Burnishing the electric clutch

WARNING: To insure maximum performance

and life, it is necessary to burnish the clutch.

Burnishing the electric clutch (Fig. 4-4) will develop
better contact between the armature and rotor, helping to
develop higher torque capabilities without slipping. The
warranty on the new clutch will be voided if it is not
burnished properly.

Use the following procedure to burnish the clutch:

1. Check the air gap between armature and rotor. Gap
should be .012” to .024”.

2. Cycle the clutch on and off 10 times (15 seconds on
and 15 seconds off) with the engine operating at half
throttles, approximately 1500 rpm.

Access to engine and hydraulic
pumps

The hydraulic pumps are accessed by lifting the seat
platform. The seat platform is hinged at the front. To raise
it, release seat latch and tilt seat platform up and forward.
The seat platform catch (Fig. 4-5) will prevent the seat from
going all the way over. However, if more access is desired
under the seat platform, the seat platform catch can be raised
allowing the seat to pivot more. Make certain to place the

control levers in the park brake position and pivot the
arm rests upward before placing the seat platform in the
full forward position to prevent arm rest damage.

WARNING: Always wear adequate eye
protection when servicing the hydraulic system
and battery.

Hydraulic system

IMPORTANT: Never use hydraulic or automatic

transmission fluid in this system; use only motor oil as
specified. Remember, dirt is the primary enemy of any
hydraulic system.

WARNING: Hydraulic oil escaping under
pressure can penetrate skin. Hydraulic oil may
cause infection in a minor cut or opening in the
skin. If exposed to hydraulic fluid, see a doctor
at once.
Before applying pressure to hydraulic system,
make sure all connections are tight and all hoses
and lines are in good condition. To find a leak
under pressure, use a piece of cardboard or wood
— never use your hands. Relieve all pressure in
the system before disconnecting or working on
hydraulic lines. To relieve pressure, lower all
attachments and shut off engine.

The 1.0 U.S. gallon (3.79 liter) hydraulic reservoir is

4-8

302638 Rev 1/05

Figure 4-6

Hydraulic

reservoir

Hydraulic filter

Figure 4-5

Seat platform catch

Control lever

Seat platform

Electric clutch

Figure 4-4

located in front of the engine and under the operator’s
platform. Fig. 4-6

Check oil level in hydraulic system after every 50 hours
of operation or weekly, whichever occurs first. Check more
often if system appears to be leaking or otherwise
malfunctioning.

Fluid level should be 1” from top of reservoir. Use only
SAE 10W40 SG, SF/CC, CD service motor oil.

Change hydraulic system filter element (Fig. 4-6) after
first 50 hours of tractor operation, then replace filter and oil
in reservoir every 500 hours thereafter. When changing
hydraulic oil use 1/2 unit (approximately 3.5 oz.) of Lubrizol
additive (Hustler P/N 027912). This additive, available
from your Hustler dealer, will increase the performance life
of the hydraulic system components.

The system filter is located to the right of the hydraulic
reservoir. A standard oil filter wrench is used to change
filter, threads are right handed. Use a Hustler approved

filter element only.

IMPORTANT: Prefill the filter element with clean oil,
before installing, to prevent drawing air into the system
pump.

1. Fill the filter element with clean system oil. Smear a
light coating of oil on upper surface of rubber seal.

2. Install the filter element on base. Tighten the oil filter
by hand until the filter seal makes contact with the
filter head, then tighten an additional 3/4 turn with a an
oil filter wrench. — DO NOT OVERTIGHTEN.

3. Start tractor engine and let run at approximately 2/3
throttle for a few minutes to work any trapped air out
of the system before engaging the steering control
lever.

4. Stop the engine and check the filter and connections
for leaks.

5. Check the hydraulic reservoir for specified oil level.
Add clean oil as necessary.

Clean or replace hydraulic reservoir cap annually. Cap
may be cleaned by dipping in or flushing with cleaning
solvent. Follow manufacturer’s instructions and warnings
for application of solvent type selected.

NOTE: The hydraulic pumps are equipped with bypass
valves. For more information refer to Operation section,
Moving tractor with stalled engine.

A hydraulic oil heat exchanger is installed on the Super
Mini Z. This heat exchanger is designed to keep hydraulic
system oil temperature lower in hot operating conditions or
heavy continuous operating conditions.

This hydraulic heat exchanger is located above the
engine. Air is drawn across the cooling fins by an electric
fan located above the heat exchanger. Fig. 4-7

Fuel system

WARNING: Observe usual fuel handling

precautions; do not smoke while refueling, do
not fill tank with engine running or while engine
is hot; allow engine to cool before storing
machine inside a building, keep fuel away from
open flame or spark and store machine away
from open flame or spark if there is fuel in the
tank. Do not refuel in enclosed trailer or other
enclosed areas. Clean up any fuel spills. Read
and observe safety precautions at front of this
manual.

The fuel tanks are located in the tractor’s fenders. (Fig.
4-8) Total capacity for the fuel tanks is 12 U.S. gallon (45.4
liter)

Use regular unleaded gasoline with an octane rating of 87
or higher.

4-9

302638 Rev 1/05

Figure 4-7

Cooling fan

Heat

exchanger

Engine

Figure 4-8

Fuel tank

Figure 4-9A

Fuel filter

Kawasaki engine

The fuel filter (Fig. 4-9A & 4-9B) is installed in the fuel
line between fuel tanks and engine fuel pump. Replace filter
annually or after every 500 hours of operation, whichever
occurs first.

When replacing the fuel filter, check the fuel line hoses
and fuel shut-off valve grommet for any cracks or leaks.

On early units a fuel shut-off valve is located on the
outlet port of each fuel tank. (Fig. 4-10A) Close these
valves (turn clockwise) to prevent fuel flow to the engine.

Current production units have a fuel shut-off valve
attached to the crossmember next to the hour meter. (Fig. 4­10B) Close this valve (center position) to prevent fuel flow
to the engine. Fig 4-10B shows the valve’s two other
positions.

Engine oil and filter

Check engine oil daily and after every 4 hours of
operation. Crankcase dipstick and oil filler tube are located
at the rear of the machine (Fig. 4-11A & 4-11B). Tractor
must be setting level when checking oil. Refer to engine
manual and maintenance schedule for oil recommendation
and capacities.

Change the engine oil and filter after the first 5 hours of
operation, per the engine manufacturer’s recommendations

4-10

302638 Rev 1/05

Figure 4-12

Pre-cleaner

Canister

Figure 4-9B

Fuel filter

Figure 4-10A

Fuel shut-off valve

Honda engine

Valve grommet

Figure 4-11B

Engine oil
drain plug

Engine

oil filter

Engine oil filler tube Honda Engine

Figure 4-11A

Engine oil

drain plug

Engine oil filter

Engine oil filler tube

Kawasaki Engine

Figure 4-10B

Fuel valve (shown in closed position)

Left fuel tank

Right fuel tank

after that. If tractor is being operated in extremely dirty
conditions, then it is recommended oil be changed more
frequently.

The oil drain and oil filter are located at the rear of the

engine. Fig. 4-11A & 4-11B

Engine air filter

Perform engine air filter maintenance per the Service

Interval chart on page 4-2.

A specially designed dry filter is standard equipment on
the Mini Z and Super Mini Z tractors and supplies clean
combustion air to the engine. Fig. 4-12

Recommended service procedure

Many engine failures can be attributed to improper air
cleaner servicing. Ingested dust and dirt will cause cylinder,
piston and bearing damage in a few hours. “Dusted”
engines will result from:

1. Overservicing the air filter element.

2. Improper installation.

3. Damaged filter, seals or canister.

4. Incorrect air filter element size.

5. Use of poorly designed aftermarket air filter elements.

Air cleaner servicing is an inexpensive maintenance
check that can prevent costly non-warrantable premature
engine damage.

Overservicing

Overservicing occurs when an air filter element is
removed for cleaning or replacement before it is necessary.
Each time the filter is removed a small amount of dirt and
dust could fall in the intake system. This accumulated dirt
can cause a dusted engine. It only takes a few grams of
ingested dirt over the normal service life of an engine to
cause a dusted engine.

Do not clean element, replace with a new element
only. Cleaning used air filter elements, through improper

cleaning procedures, can get dust on the inside of the filter
causing dirt ingestion and engine failure.

It is important to note that whenever an air filter element
is cleaned by any method, the person or company
performing the cleaning assumes responsibility for the
integrity of the filter from then on. The Donaldson

warranty for air filters expires upon cleaning or

servicing in any manner because the condition of the
filter after servicing is completely out of their control.
Therefore, on a dust ingested engine failure, there will be
no warranty consideration if the air filter element has
been cleaned or serviced in any manner.

A partially dirty air filter element works better than a
new element. Therefore, a dirty filter element is not bad for
the engine unless it is excessively restricting the air flow and
engine performance is affected. The reason is simple. The
media in the filter must be porous to allow air to pass
through it. When dirty air passes through the filter, the dirt
plugs some of the holes in the media and actually acts as
part of the filter media. When the next round of dirt enters,
the first dirt helps filter out even smaller particles making
the filter more efficient at stopping dirt from entering the
engine. This is referred to as barrier filtration.

Of course, at some point the filter media becomes too
clogged to allow air to pass.

The mowing conditions will determine the frequency of
air filter element changing.

Improper installation of an air filter element

Dust must not leak past the seals on each end of the air
filter element. The filter must be aligned within the canister
and properly seated for an effective seal so that no dirt can
enter the engine.

Damaged filter, seals or canister

Never bang or bump the filter element against the tire or
any solid object, as dust and dirt particles will be forced
through the media causing continual passing of dirt into the
engine. Visually inspect the outside of the air cleaner
canister periodically for external damage and replace if
necessary.

Incorrect air cleaner element

Use only the correct Donaldson air filter element, Hustler
part number 785261, which is designed to fit the canister
properly.

Hustler air filter elements have the correct media
composition, filter area, micron size and dimensions.
Always use genuine Hustler filters. Many aftermarket filters
have been found to be incompatible with Hustler’s canisters
and engines.

The air filter must remain intact to block passage of dirt
and foreign particles from entering the engine. Being
inclined to disbelieve the need for more expensive air filter
elements used on gasoline engines may cause some
individuals to opt for a less expensive part.

The filter element must be sufficient size and
construction to withstand stresses, caused by rapid cycling
of the air volume demanded by the engine, without cracking
or tearing under fatigue and pressure (especially diesel
engines). Therefore, Hustler Turf Equipment and the engine
manufacturers have carefully selected a reliable filter
designed to fit the needs of the engines. The filter specified
is a Donaldson filter, Hustler part number 785261.

Owners should be reminded that failure to use original
equipment replacement parts is an “alteration” and will not
be considered for warranty in the event of engine damage.

Recommended service procedure

1. Release clamps and remove element. Clean the
canister with a damp cloth.

4-11

302638 Rev 1/05

Figure 4-13

Indicator

Reset

button

2. Before installing a new element, inspect it by placing a
bright light inside and rotate the element slowly,
looking for any holes or tears in the paper. Also check
gaskets for cuts or tears. Do not attempt to use a
damaged element which will allow abrasive particles
to enter the engine.

3. Reinstall the dust cup. Make sure it seals all the way
around the air cleaner body, then tighten the clamps.

4. Check all fittings and clamps periodically for tightness
and inspect hoses for holes or cracks.

5. Periodically check the intake hose for signs of ingested
dust. Locate and repair the source of ingested dirt.

6. Never operate a machine without an air filter installed.

Air restriction indicator

Any unit with a Kawasaki engine will have an air

restriction indicator installed in the air cleaner. Fig. 4-13

Replace the element whenever the restriction indicator
shows reaches the change filter red line. Check the indicator
daily and replace element as needed or annually whichever
occurs first.

Reset the indicator by pushing in on the yellow button
after each element change. Fig, 4-13

A restriction indicator takes the guesswork out of air
cleaner servicing and allows you to safely benefit from the
filter’s optimum performance.

General engine maintenance

Detailed instructions and recommendations for break-in
and regular maintenance are specified in the Engine
Owner’s manual. Please refer to this manual for engine
servicing, lubricating oil levels with quality and viscosity
recommendations, bolt torques, etc. The engine warranty is
backed by the manufacturer. Special attention should be
paid to applicable data which will not be duplicated here.

4-12

302638 Rev 1/05

Figure 4-16

Resharpening Pattern

Do not sharpen to original pattern (below).
It is easier to get a straight cutting edge following
the resharpening pattern shown above.

Original Edge

Warped Blade (Replace)

Straight Blade

Comparison of Warped and Straight Blades

Cutting

Plane

Figure 4-17

Figure 4-15

1

Deck Belt Drive Layout

1. Spindle drive belt

2. Deck blade spindle pulley

3. Spindle belt tension idler

4. Spindle belt tension idler spring

(7.75" at operation)

5. Deck belt idler

6. Idler arm

2

2

2

6

4

5

3

5

Figure 4-14

1

2, 6

4

5

1. Pump belt

2. Engine pulley

3. Pump idler pulley

4. Pump idler arm

5. Pump pulley

6. Electric deck clutch

7. Pump idler spring

7

Viewed from

bottom for unit

5

3

Belt replacement

Figures 4-14 and 4-15 show diagrams and descriptions of

the unit’s belt drive systems.

Inspect these belts frequently for wear and serviceability.
Replace a belt that shows signs of severe cuts, tears,
separation, weather checking and cracking, or burns caused
by slipping. Slight raveling of belt covering does not
indicate failure, trim ravelings with a sharp knife.

WARNING: If the pump belt fails, loss of
control will occur especially when operating on a
slope. If you lose steering control while

operating the machine, place the steering
control levers in the park brake position
immediately. Inspect the machine and involve
your Hustler dealer to resolve the problem
before continuing to operate.

Inspect the belt pulley grooves and flanges for wear. A
new belt, or one in good condition, should never run against
the bottom of the groove. Replace the pulley when this is
the case, otherwise belt will lose power and slip excessively.

Never pry a belt to get it on a pulley as this will cut or
damage the fibers of the belt covering.

Keep oil and grease away from belts, and never use belt
dressings. Any of these will destroy the belt composition in
a very short time.

Mower blade maintenance

Check the mower blades daily, they are the key to power
efficiency and well groomed turf. Keep them sharp, a dull
blade will tear rather than cut the grass, leaving a brown
ragged top on the grass within a few hours. A dull blade
also requires more power from the engine.

Replace any blade which is bent, cracked or broken.

WARNING: Never attempt to straighten a bent
blade by heating, or weld a cracked or broken
blade as the blade may break and cause serious
injury.

DANGER: Never work with blades while
engine is running or deck clutch is engaged.
Always place deck clutch in the disengaged
position, engage parking brake and neutral lock
levers and turn engine off. Block up mower
when you must work under it. Wear gloves
when handling blades. Always check for blade
damage if mower strikes rock, branch or other
foreign object during mowing!

Mower blade removal

Use a 15/16" wrench to remove the 5/8" cap screw

holding the blade to the spindle shaft from underneath.

Sharpen the blades on a grinder following pattern as
shown (Fig. 4-16). Touch-up sharpening can be done with
a file.

Check the blades for balance following grinding. A
commercial balancing tool is available through most
hardware supply stores, or balancing can be done by placing
the blade on an inverted line punch or 5/8" bolt. Blade
should not lean or tilt. Spin the blade slowly, blade should
not wobble. If blade is out of balance, true it up before
reinstalling.

Lay the blade on a flat surface and check for distortion
(Fig. 4-17 and 4-18). Replace any distorted blade.

Do not re-use spindle bolts which have stripped, worn or
undercut threads. Torque bolts to 118 foot-pounds when
reinstalling blades.

WARNING: When mounting blades, rotate
them after installation to ensure blade tips do not
touch each other or sides of the mower.

WARNING: Failure to correctly torque the bolt
may result in the loss of the blade which can
cause serious injury.

WARNING: Mower blades are sharp and can
cut. Wrap the blade(s) or wear gloves and use
extra caution when servicing them.

4-13

Figure 4-18

Twisted Blade Edge

(Replace)

Cutting Edge

Straight Blade Edge

End view of blades, comparing

twisted and straighten blades.

Cutting Plane

Cutting Edge

302638 Rev 1/05

ADJUSTMENTS

Introduction

WARNING: Unless specifically required, DO

NOT have engine running when servicing or
making adjustments to tractor. Place control
levers in the park brake position and remove
ignition switch key. Repairs or maintenance
requiring engine power should be performed by
trained personnel only. To prevent carbon
monoxide poisoning, be sure proper ventilation
is available when engine must be operated in an
enclosed area. Read and observe safety warnings
in front of manual.

Your Mini Z or Super Mini Z was adjusted before it left
the factory and was checked during predelivery setup.
However, after start-up and continued use, a certain amount
of break-in wear will cause some adjustments to change.

Remain alert for unusual noises, they could be signaling
a problem. Visually inspect the machine for any abnormal
wear or damage. A good time to detect potential problems
is while performing scheduled maintenance service.
Correcting the problem as quickly as possible is the best
insurance.

WARNING: Keep your machine clean and
remove heavy deposits of trash and clippings,
they can cause engine fires and hydraulic
overheating as well as excessive belt wear.

Clear away heavy build-up of grease, oil and dirt,
especially in the area of reservoir and oil and engine
combustion air; minute dust particle are abrasive to close­tolerance engine and hydraulic assemblies.

Some repairs require the assistance of a trained service
mechanic and should not be attempted by unskilled
personnel. Consult your Hustler service center when
assistance is needed.

Torque values

WARNING: Particular attention must be given

to tightening the drive wheel lug nuts, wheel
motor nuts, and blade spindle bolts. Failure to
correctly torque these items may result in the
loss of a wheel or blade, which can cause serious
damage or personal injury.

Torque values given below:

Ft-lbs. Nm

Wheel (lug) nuts ................................65-75......88.14-101.7

Wheel motor nut ............................290-310 .....393.2-420.4

Blade spindle bolt top ...........................118 ................160.0

Blade spindle bolt bottom .....................118 ................160.0

It is recommended that these be checked after the first 2
hours of operation, initially and every 50 hours following
removal for repair or replacement.

For engine torque values, see engine owner’s manual.
For all other torques refer to the parts manual for

standard torque chart.

Steering linkage

The neutral adjustment for the control levers in the neutral

position is discussed in this section.

The tractor steering has been factory adjusted to eliminate
creeping when the control levers are in the neutral position
(Fig. 5-1). However, should the tractor begin to creep, the
control lever linkage can be adjusted as follows:

Control Lever Neutral Adjustment

Before considering any adjustment, check the tire air
pressure and make certain hydraulic system oil is at
operating temperature. Unequal tire pressure will cause the
tractor to drift to one side. Refer to tire pressure information
in the Maintenance section of this manual.

Fine adjustment to the unit’s steering is made with the
adjustable pump linkage rods located between the control
lever and pump arms. Fig. 5-2

Neutral is properly adjusted when the control levers are in
the neutral position and the drive wheels are not turning.

5-1

302638 Rev 1/05

Figure 5-1

Park brake slot

Control lever
in the neutral

position

Control

lever

Figure 5-2

Pump

linkage

rod

Jam nut

If the tractor creeps in the neutral position the control

linkage may be adjusted as follows:

1. Raise and block the tractor up so the drive wheels are
off of the floor.

WARNING: Make certain machine is secure
when it is raised and placed on the jack stands.
The jack stands should not allow the machine to
move when the engine is running and the drive
wheels are rotating. Use only certified jack

stands.

2. Position the control lever in the neutral position.

Disengage the deck clutch.

3. Start the engine and observe which way the wheels are
rotating.

4. If wheel(s) are rotating forward, loosen the jam nuts on
the pump linkage rods and rotate the rod to lengthen
the steering control linkage until the wheel(s) come to
a stop. Fig. 5-2
NOTE: The left linkage controls the left hydraulic
pump and the right linkage controls the right hydraulic
pump.
Repeat for the opposite side if necessary.

5. If wheel(s) are rotating in reverse then loosen the jam
nuts on the pump linkage rods and rotate the rod to
shorten the steering control linkage until the wheel(s)
come to a stop. Fig. 5-2
NOTE: The left linkage controls the left hydraulic
pump and the right linkage controls the right hydraulic
pump.
Repeat for the opposite side if necessary.

6. When both wheels remain in neutral, tighten the jam
nuts to lock the turnbuckle in place.

7. Test again by moving the control levers forward and
backward before returning them to the neutral position.
If the tires are in neutral, the unit is now ready for
operation.

8. After adjusting for neutral it may be necessary to re­adjust the steering dampener and/or the control lever
stop. Fig. 5-3 or Fig. 5-4

Control lever stops

The control lever stops (Fig. 5-3) are designed to do two
things: First, and most important, they must keep the pumps
from bottoming out internally. Secondly, the stops may be
adjusted to help drive straight when the control levers are
pushed forward against the stops.

To keep the pumps from bottoming out internally use the
following procedure:

1. To make the first adjustment the tractor engine must
NOT be running.

2. Check to make sure the control levers are against the
stops before the pumps are bottomed out internally.
To do this, gently and slowly move the control levers
forward and feel if there is some resistance on the
pump lever before the control levers hit the stops.
Check one side at a time. If you sense that the pump
arms are stopping the forward motion of the control
arms, loosen the jam nut on the adjustable stop of the
corresponding side and turn the stop (set screw) inward
to stop the control levers slightly before the pump
bottoms out. Lock in place when the adjustment is
correct by re-tightening the jam nut.

3. Do this for each side.

To adjust the stops for driving straight when control levers

are against the stops during operation:

1. Determine which drive tire is rotating too fast when
both control levers are against the stops. Then stop the
tractor and loosen the lock nut on the side which is
rotating too fast and turn the stop (set screw) inward to
stop the control lever sooner. Tighten the lock nut on
the stop and test again. Repeat this procedure until
unit drives straight.

NOTE: Since this is a hydrostatic drive, variables such

as temperature of oil, efficiency of pumps and motors, tire

pressure etc. may effect the consistency of the ability to rely

on the stops to drive straight without the operator making

minor steering adjustments with the control arms.

Steering dampener

This steering dampener (Fig. 5-4) is spring loaded to
return the control levers to the neutral position from the
reverse position. This gives the operator a sense of neutral
during operation.

To set the steering dampeners in the correct operating
position follow these steps:

1. Place the control lever in the neutral position.

2. Loosen the steering dampener’s front ball stud.

3. Pull the dampener spring housing pass the point that

the internal spring is engaged.

4. Release the dampener spring housing and allow the
internal spring to bring the housing back to the neutral
position.

302638 Rev 1/05

5-2

Figure 5-3

Control

lever

Stop

Jam

nut

Control lever adjustment

The control levers can be adjusted for operator comfort.
By loosening the cap screws that attaches the upper control
lever to the lower lever (Fig. 5-5), the upper control lever
can be pivoted to fit the operator’s personal preference.

The control levers should be adjusted so that they align
with each other when in the neutral position.

Park brake adjustment

Occasionally check the park brakes and adjustment using
the following method:

1. Position the control levers in the neutral position.
Disengage the deck clutch.

WARNING: Make certain machine is secure
when it is raised and placed on the jack stands.
The jack stands should not allow the machine to
move when the engine is running and the drive
wheels are rotating. Use only certified jack

stands.

NOTE: The front brake link is not adjustable. Fig. 5-6

2. Raise and block the tractor up so the drive wheels are
off of the floor.

3. Open the hydraulic pump’s bypass valve (Fig. 5-7), on
the side that is being adjusted, by turning bypass valve
counter clockwise one-half to one revolution. The
valve stems on each hydraulic pump are located near
the top and are identified as a hex stud.

4. Rotate the tire. The tire should rotate. Remember
hydraulic oil resistance will prevent the tire from
rotating freely even with the bypass valves open.
There should be no resistance from the brakes at this
point.

5. Move the control lever to where it is just inside (1/8”)
the park brake slot. Fig. 5-8
NOTE: When the control lever is against the outside
edge of the the slot, the brakes should not be engaged.
Fig. 5-9

6. Rotate the tire. If the brake is adjusted properly the
tire will still rotate but friction will start to become
noticeable here. However, if no brake resistance is

noticed, the brake needs adjusted as follows:

7. Loosen the brake linkage jam nuts. Fig. 5-10

8. Rotate the tire and at the same time rotate the

turnbuckle to shorten the length of the brake linkage to
increase the brake pressure. When you feel the brake
begin to engage, stop adjusting the turnbuckle. Re­tighten the jam nuts on the turnbuckle.

9. Place the control lever in the park brake slot (Fig. 5-

11). The tire should not rotate when the control lever
is in the park brake position.

10. Place the control lever in the neutral position. The tire
should rotate freely.

11. Close the hydraulic pump’s bypass valve.

12. Repeat steps 3 thru 11 for the other side.

13. Remove the jack stands and lower the unit. It is now

ready to operate.

Hydraulic pump belt adjustment

The pump drive belt tension remains constant by means of

a tension idler and spring (Fig. 5-12). There is no tension
adjustment of this belt. NOTE: Replace the belt every 400

302638 Rev 1/05

5-3

Figure 5-5

Cap screw

Upper

control

lever

Lower control

lever

Figure 5-4

Spring

housing

Front ball

stud

Figure 5-6

Front brake link

(right side)

Steering dampener

with spring

hours or every two (2) years whichever comes first.

WARNING: If the pump belt fails, loss of
control will occur especially when operating on a
slope. If you lose steering control while

operating the machine, place the steering
control levers in the park brake position
immediately. Inspect the machine and involve
your Hustler dealer to resolve the problem
before continuing to operate.

Deck drive belt adjustment

The spindle belt tension remains constant by means of a
tension idler and spring (Fig. 5-13). The spring tension
should be such that the belt does not slip under normal
operating load conditions, assuming the belt is not
excessively worn or damaged. As belt stretches and wears
in, adjustment may become necessary. To increase belt
tension, move the spring chain one (or more) link(s) at the
anchor bracket (Fig. 5-13). Installed spring length should be

7.75" ± .3" (19.7 cm ± .76 cm) originally with adjustments
of .60" (15.2mm) per chain link. (Fig. 5-14)

IMPORTANT: Do not over tension the spring to
compensate for a badly worn belt or pulley.

Engine RPM setting

The Mini Z and Super Mini Z are designed so that the
engine will run at 3600 rpm static pump load only. At this
speed the hydraulic pumps are running at their maximum
rated speed.

Deck leveling and height adjustment

The mower deck has three areas that may need to be
checked and adjusted periodically. Before considering any
mower deck leveling adjustments, check that the tire air
pressure is within the specified range.

Deck level adjustments

Leveling the deck must be done in the following manner

302638 Rev 1/05

5-4

Figure 5-11

Figure 5-8

1/8”

Outside edge

Control lever

Park brake

slot

Figure 5-9

Travel slot

Outside edge

Control lever

Park brake slot

Figure 5-10

Turnbuckle

Brake linkage

Jam nut

Jam nut

Figure 5-7

Bypass valve

Control lever in park brake position

and order:

1. Check tire pressures to make certain they are properly
inflated before starting to level deck. The
recommended pressures are as follows:

Drive wheels tire pressure....................8 - 10 psi

Gauge wheels tire pressure...................8 - 10 psi

WARNING: Stop engine. Make sure deck
clutch switch is in the down (OFF) position.
Place control levers in the brake position before
leaving machine.

2. Park the unit on a flat surface.

3. Raise deck and place 3" of blocking under all 4 corners

of the deck (Fig. 5-15). This will set the cutting height
at 3 ¼ ". NOTE: Back of deck will automatically be
set ¼" higher.

4. Set cutting height at 3 ¼" in the height indicator by
placing the height adjusting stop in the 3" hole, and
turning the height stop so that the flat side is against
the stop handle. Fig. 5-16

5. Clamp the height adjusting stop against the stop handle
(5-16). This will assure that the height will not move
during the setting process. Otherwise, spring pressure
from the deck lift springs will tend to pull the stop
away from the handle.

6. Loosen all nuts on the deck lift threaded rods, and the
hardware on the adjuster (on the right front), until all

5-5

302638 Rev 1/05

Figure 5-14

1.75”

Spring Extension

7.75”

6.0”

Normal Spring Length

Figure 5-12

Spring

Tension

idler

Pump drive

belt

Figure 5-13

Spring

Tension idler

Chain

Figure 5-15

Blocks

Figure 5-17

Deck lift threaded rod

Nut

Nut

Chains

Figure 5-16

Height

adjusting

stop

Stop

handle

the deck lift chains are loose, and the deck is sitting
tightly on all four blocks. Fig. 5-17, 5-18, 5-19

7. Loosen the two nuts on the front of height indicator so
that the foot pedal is free. Fig. 5-20

8. Start the leveling process on the left front of the
tractor.

9. Set the amount of threads protruding on the deck lift
rod from the lift block at approximately 1". Fig. 5-21

10. Jam both nuts against the block.

11. Push or pull on the deck lift foot pedal until the chain

on the left front just becomes tight, making sure that
the deck stays tight against the 3" block.

12. While keeping the chain tight, tighten the nuts against
the deck lift block on the height indicator rod. Fig. 5­20

13. Go to the right front of the tractor.

14. Loosen the 5/16" jam nut on the adjuster lift chain (5-

19), and back the adjuster bolt out to allow the adjuster
to move up and down freely.

15. Be sure that adjuster is free to move up and down.

16. Tighten the adjuster bolt until the chain just becomes

tight, making sure that the deck stays tight against the
3" block.

17. Tighten the adjuster bolt jam nut to prevent the
adjuster bolt from moving. Fig. 5-19

18. Tighten the hardware holding the chain and adjuster
onto the deck lift arm.

19. Go to the right rear of the tractor.

20. Make sure that there is still slack in the chain. If not,

loosen the two nuts on the block holding the threaded
rod until there is slack in the deck lift chain. Fig. 5-18

21. Tighten the appropriate nut until the chain just
becomes tight, making sure that the deck stays tight
against the 3" block.

22. Tighten the other nut on the opposite side of the block,
and jam them tightly together against the block.

23. Go to the left rear of the tractor.

24. Make sure that there is still slack in the chain. If not,

loosen the two nuts on the block holding the threaded
rod until there is slack in the deck lift chain. Fig. 5-17

25. Tighten the appropriate nut until the chain just
becomes tight.

26. Tighten the other nut on the opposite side of the block,
and jam them tightly together against the block.

27. Compress the deck lift assist springs so that there is 1”
of space between the front nut and on the spring and
the rear nut on the deck lift block (Fig. 5-21). Typical
both sides.

28. When completed, all chains will be tight, and deck
cutting height will be set to the deck height indicator.

Deck cutting height adjustment

Deck height is adjustable from 1-1/2” to 4-1/2” (3.81 cm

- 11.43 cm) in 1/4” increments. The holes in the height
adjusting bar are spaced at 1/2” intervals. By turning the
height adjusting stop around, 1/4” increments can be
attained due to the 1/4” plate that is part of the stop. Fig. 5­22

EXAMPLE: When the height adjusting stop is placed in

the 1-1/2” hole, with the 1/4” plate facing to the front of
the unit, the cutting height is at 1-1/2”. When the height
adjusting stop is placed in the 1-1/2” hole, with the 1/4”
plate on the operator’s side of the hole, the cutting height
is at 1-3/4”.

When the height adjusting stop is placed in one of the
holes, with the 1/4” plate on the operator’s side of the hole,
the deck height will be set at one of the following: 1-3/4”, 2­1/4”, 2-3/4”, 3-1/4”, 3-3/4” or 4-1/4”.

302638 Rev 1/05

5-6

Figure 5-20

Foot

pedal

Nuts

Figure 5-19

5/16” bolt

Adjuster

Hardware

Jam nut

Figure 5-18

Deck lift

threaded

rod

Nut

Nut

Chains

When the height adjusting stop is placed in one of the
holes, with the 1/4” plate facing to the front of the unit, the
deck height will be set at one of the following: 1-1/2”, 2”, 2­1/2”, 3”, 3-1/2”, 4” or 4-1/2”.

The notch located at the rear of the right height adjusting
bar (4-1/2” height) is to be used when the deck is placed in
the transport mode.

Anti-scalp wheels

Anti-scalp wheel kits are standard on the Mini Z. These
anti-scalp wheels are designed to minimize scalping when
mowing on rough uneven terrain.

After setting the cutting height, adjust the front anti-scalp
wheels so they extend below the deck but do not contact
the ground. They should always be at least 1/4” to 3/4” (.6
cm to 1.9 cm) below the deck. With the unit sitting on a flat
level surface, the front wheel position can be adjusted up or
down as needed from 3/4” to 1-3/4” (1.9 cm to 9.5 cm)
below the blade surface. Move the front wheels up or down,
in 1/2” (1.3 cm) increments, using the different axle mount
holes in the wheel mount bracket. Fig. 5-23

When adjusting the rear anti-scalp wheels, the wheel
should be in the lower axle mount hole when the front anti­scalp wheels are in the lower or middle axle mount holes.
When the front wheels are in the upper axle mount hole, the
rear wheels should be in the upper axle mount hole as well.

NOTE: When the anti-scalp wheels are installed, the
minimum cutting height is 1” (2.5 cm) with the anti-scalp
wheels set at 3/4”.

5-7

302638 Rev 1/05

Figure 5-23

Adjusting

holes

Anti-scalp

wheel

Figure 5-22

Height

adjusting

stop

1/4” plate

Figure 5-21

Lift block

1”

Deck lift rod

1”

Deck lift

assist springs

302638 Rev 1/05

SYMPTOMS PROBABLE CAUSES SUGGESTED REMEDIES

Starting motor Control handle not in park Place control handle in park

does not crank brake position or switch not brake position or re-adjust

adjusted switch

Mower clutch switch engaged Disengage clutch switch

Weak or dead battery Recharge or replace

For additional causes See engine manual

Engine cranks but No fuel or line Fill tank or replace

does not start plugged line

Numerous See engine manual

Engine: Numerous See engine manual

Runs with continuous
misfiring or engine runs
unevenly or erratically

Loss of power or Restrictions in air cleaner Service air cleaner

system will not operate
in either direction Hydraulic line blockage See your dealer

Internal interference or See your dealer
leakage in wheel motor

Insufficient hydraulic Check level in reservoir
oil supply

Have dealer check
hydraulic pump

Poor compression See your dealer

Steering linkage Adjust linkage
needs adjustment

Air in system Check filter & fittings

For additional causes See engine manual

Overheating Air intake screen or Clean screen and fin

cleaning fins clogged

For additional causes See engine manual

Low oil pressure Low oil level Add oil

Oil diluted or too light Change oil and check for

source of contamination

High oil consumption Numerous See your dealer

Tractor jerky when starting Steering control linkage Adjust linkage

or needs adjustment

operates in one direction

only Pump or wheel motors See your dealer

faulty

Hydraulic system operates Low hydraulic oil level Fill reservoir

hot (oil in reservoir
smells rancid) Hydraulic pump faulty See your dealer

Tractor creeps when Steering linkage needs Adjust linkage

steering control levers adjustment
are in neutral

Tractor circles or veers Steering linkage needs Adjust linkage

in one direction adjustment

Wheel motors faulty See your dealer

Hydraulic pump faulty See your dealer

Tractor creeps when Steering linkage out of Adjust steering linkage
parking brake engaged adjustment

Brakes need adjustment Adjust parking brakes

TROUBLESHOOTING

The majority of operating problems that occur with a system can be traced to improper adjustments or delayed service. A
consistently applied preventative maintenance program, as outlined in the maintenance section of this manual, will prevent
many problems. The following chart is designed to help you locate a problem by suggesting probable causes and the

6-1

302638 Rev 1/05

7-1

When storing the unit at the the end of the mowing
season, the following steps should be taken to ensure
readiness for the next mowing season.

1. Remove all grass, dirt, and trash from tractor and
mower. Clean tractor and mower and touch up all
scrapes with Hustler spray paint.

2. Clean paper air filter. Replace if necessary. Wash and
re-oil foam precleaner.

3. Check thoroughly for any worn or damaged parts that
need replacing and order them from your dealer.

4. Thoroughly lubricate machine, according to
lubrication instructions.

5. Check hydraulic oil level. Add oil if necessary.
Change oil and filter if not done in last 500 hours.
Lubrizol additive is required. Refer to Maintenance
section.

6. Block tractor up so weight is off tires.
NOTE: Do not deflate tires.

7. Protect battery from freezing temperatures.
Occasionally recharging battery during storage will
extend battery life.

8. Perform separate engine preparation as listed below.

9. Store tractor in a clean, dry place.

Preparation of engine for storage

When engine is to be unused for long periods, proceed as

follows:

1. Run engine for a minimum of 15 minutes.

2. Drain oil from crankcase while engine is still warm.

3. Refill with fresh oil of proper viscosity.

4. Drain fuel tank and run the engine until it stops from

lack of fuel. Gasoline evaporates if left in carburetor
for long periods, forming gum and varnish deposits in
carburetor. These deposits will cause engine flooding
and loss of power.

5. Remove and replace fuel filter if not done in previous
100 hours.

6. Remove spark plugs and pour a tablespoon of engine
oil into each spark plug hole, Install plugs, but do not
reconnect plug leads.

7. Crank engine with starter at least a dozen revolutions
to distribute oil over cylinder walls and valve
mechanism.

8. Clean exterior surface of engine. Spread a light film
of oil over any exposed metal surfaces of engine that
are subject to corrosion.

9. Clean dirt and chaff from cylinders and fins, blower
housing and muffler.

10. Check oil filler cap and fuel tank cap to make certain
they are securely in place.

Preparation of battery for storage

When the machine is to be unused for long periods, it is
best to disconnect the battery and remove it from the unit.
At this time perform the following battery maintenance:

1. Clean battery

2. Check the electrolyte level

3. Charge the battery, if necessary

4. Store battery in a cool, dry place (do not expose to

freezing temperatures)

5. Always keep the battery fully charged. (Especially
important to prevent battery damage when the
temperature is below 32F.)

New season preparation

Before starting the tractor following post season storage,

the following servicing is required:

1. Clean tractor, removing trash and dirt accumulation.

2. Check engine oil and hydraulic oil levels.

3. Fill fuel tank with fresh gasoline. Run machine at half

speed for 5 minutes, checking operation of steering
control lever. Stop engine and check for oil leaks,
loose fittings and so forth.

4. Tighten any bolts that have loosened and make sure all
hair pins, cotter pins and clevis pins are in place.

5. Install all safety shields and review safety precautions
listed in this manual.

6. Check and inflate tires to 8-10 psi.

STORAGE

This section contains sources of additional literature
concerning your tractor. Literature should be ordered from
your Hustler dealer or direct from indicated source.

Mini Z & Super Mini Z Parts Manual

If you would like to order a Parts Manual for this tractor,
the Hustler p/n for that manual is listed below. Please call
Hustler Turf Equipment at [phone] to order the
manual. You may also mail, FAX, or e-mail your order by
using the form on page 8-3. Hustler Turf Equipment will
accept credit card payment for this manual.

Engine information

The Mini Z uses a Kawasaki 23hp or 25hp engine and a
Honda 24hp engine. The Super Mini Z uses a Kawasaki
25hp engine or a Honda 24hp engine. Primary source of
information is the engine operator’s manual, which is
included with the owner’s manual packet. For additional
copies order Hustler P/N 778423 (Kawasaki) or Hustler P/N
785642 (Honda).

For additional engine service manual information contact
your local Kawasaki or Honda dealer.

302638 Rev 1/05

Hydraulic pump information

Power to wheel motors is supplied by two Hydro-Gear
hydraulic pumps.
For more information:

Hydro-Gear
Customer Services
1411 So. Hamilton Street
Sullivan, IL 61951
Phone: [phone]

NOTE: During warranty period, check with your Hustler
dealer before attempting repairs on any tractor system.
Unauthorized repair work can void warranty of tractor,
engine, and other components.

Wheel motors information

For more information on Super Mini Z wheel motors:

White Hydraulics
P.O. Box 30250
Nashville, TN 37241-0250
Phone: [phone]

NOTE: During warranty period, check with Hustler
dealer before attempting repairs on any tractor system.
Unauthorized repair work can void warranty of tractor,
engine, and other components.

PRODUCT LITERATURE

8-1

Parts

Model Manual List

Model Number P/N Price

Mini Z 927228, 927236, 927251, 927244 302612 $22.50

Super Mini Z 927269, 927285, 927277 302620 $22.50

ORDER

MANUFACTURER’S HUSTLER

DESCRIPTION PART NUMBER PART NUMBER

Kawasaki Service Manual 9924-2045-02 771535
Honda Service Manual 61-ZJ-410Z 787671

FREQUENTLY ORDERED PARTS

Part No. Description

027912 Lubrizol 7 oz. bottle
027920 Lubrizol 10 oz. bottle
768341 Hydraulic oil filter (Mini Z only)
783936 Hydraulic oil filter (Super Mini Z only)
786533 Pump drive belt
791335 B-Section belt, 44” deck (927228, 927236, 927269)
789388 B-Section belt, 52” deck (927251, 927244, 927285, 927277)
068478 Fuel filter (Kawasaki)
785626 Fuel filter (Honda)
772079 Engine oil filter (Kawasaki)
785634 Engine oil filter (Honda)
783753 18” blade
784256 16” blade
785428 16” gator blade
785436 18” gator blade
785261 Remote filter element

302638 Rev 1/05

8-2

Mini Z Parts Manual (P/N 302612) Order Form

Super Mini Z Parts Manual (P/N 302620) Order Form

To order by mail:

Fill out this form, fill out the credit card information or attach a check and send it to:

Hustler Turf Equipment
P.O. Box 808
Hesston, KS 67062

To order by e-mail:

Using this form as a guide, send all necessary information, including credit card information to:

[e-mail]

To order by Telephone or FAX:

Telephone: call [phone] to place an order
FAX this completed form to [phone]

Name:

Address:

Telephone:

Master Card Number: Expiration Date:

Visa Card Number: Expiration Date:

QTY Part Number Description Unit Price Total Price

302612 Mini Z Parts Manual $22.50
302620 Super Mini Z Parts Manual $22.50

302638 Rev 1/05

8-3

302638 Rev 1/05

8-4

302638 Rev 1/05

9-1

TECHNICAL SPECIFICATIONS

Starter 12-volt (.8 KW), solenoid shift positive engagement.

Ignition Electronic.

Charging System 12-volt, 15-amp.

Fuel Unleaded gasoline with octane rating of 87or higher.

Fuel Filter Replaceable, automotive-type.

Air Cleaner Heavy-duty air cleaner to extend the service

interval for excessive, dirty applications and improve
performance.

Cooling Air cooled. Fly-wheel fan.

Governor Mechanical.

TRACTION DRIVE SYSTEM:

Type Dual hydrostatic. Individual pumps power two direct-

drive wheel motors. Hydrostatic system operates on 10W40
motor oil.

Hydraulic Lines Stainless-steel high-pressure lines with
Parker Seal-Lok™ O-Ring Face Seal Fittings.

Pumps Two variable displacement, axial piston type. Each
pump powers one drive-wheel motor. Mini Z: Hydro-gear
BDP10 Super Mini Z: Hydro-gear BDP16 2-year warranty

on hydraulic pumps.

Pump Drive V-belt drive from engine crankshaft.

Final Drive White CE 12 direct-drive high-torque wheel

motors. One for each drive wheel. 2-year warranty on
hydraulic wheel motors.

Filter 40 micron, replaceable spin-on type.

Ground Speed infinitely variable

Hustler Mini Z:
0-9

MPH

(0-14.48

KPH

) forward

0-7

MPH

(0-11.27

KPH

) reverse

Super Mini Z:

Transport 0-13

MPH

(0-20.92

KPH

) forward

Mowing 0-10

MPH

(0-16.09

KPH

) forward

0-7

MPH

(0-11.27

KPH

) reverse

Steering Twin-lever steering provides independent control
of each drive wheel. Speed, forward, reverse, brake, and
turns are all controlled with hand-operated controls.

Turning Radius True zero degree. Turns within its own
length. Counter-rotating, independent drive wheels.

BRAKES:

Service Hydrostatic dynamic braking.

Parking Automotive-style drum brakes. When steering

levers are placed in neutral position, integral park brakes are
automatically engaged.

Mower Drive Single V-belt drive from engine with electric
clutch. Spring tension idler for long belt life.

TIRES:

Front 13 x 5.00 – 6, no tread.
Drive 23 x 9.50 – 12, turf tread.

CAPACITIES:

Fuel System 12 US

GAL (45.4 L).

Hydraulic Oil 2 US GAL

(7.57 L)

DIMENSIONS: Height 40

IN (101.6 CM)

W/52 in Deck Length 74 IN (187.96 CM

)

Overall width (w/discharge chute up 53

IN (134.6 CM

)

Tire-to-tire width 53

IN (134.6 CM

)

Weight Mini Z: 985 lbs (446.79 kg) Super Mini Z: 995

LBS

(451.32 KG)

W/44 in Deck Length 74

IN (187.96 CM)

Overall width (w/discharge chute up) 53

IN (134.6

CM)

Tire-to-tire width 44

IN (111.76 CM)

Weight Mini Z: 995 lbs (451.32 kg) Super Mini Z: 995

LBS

(451.32 KG

)

SAFETY FEATURES: Operator presence system
connected to deck and drive clutches. Stabilizer rollers at
rear of tractor.

SEAT: Molded-vinyl seat with armrests. Fore and aft
adjustment. Optional spring suspension.

CONSTRUCTION: Mainframe is 1.5

IN x 2 IN x .125 IN

(3.8 CM x 5.08 CM x .32 CM) rectangular steel tubing. Drive
motors mounted to .179

IN (.45 CM) welded steel. Front

caster wheels mounted with roller bearings on each wheel.
Front caster forks are .375

IN (.95 CM) steel.

DECK LIFT: Foot-operated deck height adjustment. Pin
for setting height, transport position.

CONTROLS: Hand-operated choke/throttle, ignition
switch, electric mower clutch. Integrated parking brakes.

INDICATORS: Hour meter, engine warning light.

CUP HOLDER: Two cup holders molded into the left side

fuel tank. Accommodates nearly any cup size including Big
Gulp.

ATTACHMENTS

44” and 52” Side-Discharge Decks

Type Free-floating mower using three blades with center

blade to the front. Mower is suspended at the corners.
Includes deck-mounted rollers to improve flotation in
rolling and uneven terrain.

Deck Lift Raise and lower deck from driver’s seat with
simple foot-operated deck height adjustment. Pin for setting
height, transport position. Change cutting heights, hop curbs
and trailer more easily.

Construction .125

IN (.32 CM) welded steel with .125 IN

(.32 CM) doubler on deck plate. Solid 1 IN x .375 (2.55 CM X
.95 CM) steel bars reinforce impact areas on trim edges. .187

IN (.47 CM) IN box-section reinforced front edge.

Reinforcements welded onto spindle mount areas. Steel
deck housing is 4

IN (10.16 CM) deep for high-capacity

mowing.

Cutting Heights Foot-operated deck height adjustment. Pin
for setting height, transport position. Height adjustment in
.25

IN increments from 1.5 IN to 4.5 IN (3.81 CM to 11.43

CM).

Mowing Blades Heavy-duty, heat-treated, high-lift steel
blades 21

IN x 2.75 IN x .25 IN

Blade Tip Speed 44 IN: 16,100 FPM 52 IN: 18, 300 FPM

Blade Drive V-belt drive to all three spindles. Spring

tension idler pulleys.

Spindles Machine aluminum housing, 1

IN (2.5 CM

)

diameter high carbon steel shafts and sealed ball bearings.

Flotation Suspended mower floats on four spring-assisted
chains. 4 anti-scalp wheels are standard.

Width of Cut 44

IN (111.76 CM) 52 IN (132.08 CM)

Trim Capacity (left side) 44

IN: .5 IN (1.27 CM) 52 IN:6 IN

(15.24

CM)

ACCESSORIES

Mulch Kit Recycles clippings under deck allowing

clippings to be cut and recut, then discharged down into the
grass. Reduces handling of clippings, improves appearance,
and recycles nutrients back to the soil.

BAC-VAC

™

Catcher Rear-mounted, 9-bushel hopper is

dumped from the seat without leaving the machine. Blower
is powered from right-side deck spindle (no pony engine
required). Hopper and blower can be added or removed in
seconds. Capacity: 9 bushels Dimensions: Overall
Height: 51” Overall Length: 104” Overall Width: w/60”
deck: 74.48” Hopper Weight: 150 lbs. Blower Assembly
Weight: 75 lbs. Blower Housing: .134 thick abrasion
resistant steel side wall; .179 thick. steel top and bottom
Blower Impeller: .179 thick.
abrasion resistant steel impeller blades; .179 thick. backing
plate Blower Transfer Chute: .187 thick. polyethylene
(black) Blower Type: 11” diameter, V-belt driven (“B”
section) Delivery Tube: Clear 6” I.D. heavy-duty flexible
polyvinyl-lchloride tube Hopper: .15 thick reinforced
fiberglass supported by steel frame Hopper Rear Door
Cover: .15” thick polyethylene (black)

Specifications subject to change without notice.

Kawasaki Kawasaki Kawasaki Honda

Horsepower 19 23 25 24
No. of Cylinders 2 2 2 2
Displacement 41.2 CU IN (675 CC) 41.2 CU IN (675 CC) 41.2 CU IN (675 CC) 40.9 CU IN (670 CC)
Compression Ratio 8.1:1 8.1:1 8.1:1 8.3:1
Max. Torque 37.0

FT LBS @ 2400 RPM 39.8 FT LBS @ 2400 RPM 41.2 FT LBS @ 2400 RPM 37.5 FT LBS @ 2500 RPM

Engine Specifications

302638 Rev 1/05

INDEX

PAGE

Access to engine and hydraulic pump..............................4-8

Adjustment introduction...................................................5-1

Anti-scalp wheels .............................................................5-6

Belt replacement.............................................................4-13

Brake specifications .........................................................9-1

Burnishing the electric clutch...........................................4-8

Capacities specification....................................................9-1

Construction specification................................................9-1

Control lever adjustment ..................................................5-3

Control lever stops ...........................................................5-2

Controls ............................................................................3-1

Controls specifications .....................................................9-1

Cup holder........................................................................9-1

Cutting height specifications............................................9-1

Decals...............................................................................2-4

Deck cutting height adjustment........................................5-6

Deck drive belt adjustment...............................................5-4

Deck leveling and height adjustment ...............................5-4

Deck lift specifications.....................................................9-1

Dimensions.......................................................................9-1

Driving the tractor ............................................................3-3

Electrical system ..............................................................4-3

Engine air filter ..............................................................4-10

Engine information...........................................................8-1

Engine oil and filter........................................................4-10

Engine rpm setting ...........................................................5-4

Engine specifications .......................................................9-1

Engine starting .................................................................3-2

Frequently ordered parts ..................................................8-2

Fuel system.......................................................................4-9

General engine maintenance ..........................................4-12

Hour meter .......................................................................4-3

Hydraulic pump belt adjustment ......................................5-3

PAGE

Hydraulic pump information............................................8-1

Hydraulic system..............................................................4-8

Indicators..........................................................................9-1

Instrumentation ................................................................3-2

Lubrication .......................................................................4-3

Maintenance introduction.................................................4-2

Mini Z Parts Manual .................................................8-1, 8-3

Model and serial number..................................................1-1

Moving tractor with stalled engine ..................................3-3

Mower blade maintenance .............................................4-12

Mower blade removal ....................................................4-13

Mower deck operation......................................................3-5

New season preparation ...................................................7-1

Operating suggestions ......................................................3-4

Park brake adjustment ......................................................5-3

Parts and service...............................................................1-1

Preparation of engine for storage .....................................7-1

Safety features specifications...........................................9-1

Safety interlock system ....................................................3-2

Seat...................................................................................9-1

Slope guide.......................................................................2-5

Steering dampener............................................................5-2

Steering linkage................................................................5-1

Super Mini Z Parts Manual.......................................8-1, 8-3

Tires..................................................................................4-3

Tire specifications ............................................................9-1

To the new owner.............................................................1-1

Torque values............................................................4-2, 5-1

Traction drive system specification .................................9-1

Tractor and deck warranty ...............................................1-2

Using this manual.............................................................1-1

Warranty registration .......................................................1-1

Wheel motor information.................................................8-1

10-1