HP HCPL-3150 Datasheet

1-197

H

0.5 Amp Output Current IGBT
Gate Drive Optocoupler

Technical Data

HCPL-3150

Features

• 0.5 A Minimum Peak Output
Current

• 15 kV/µs Minimum Common
Mode Rejection (CMR) at
VCM = 1500 V

• 1.0 V Maximum Low Level
Output Voltage (VOL)
Eliminates Need for
Negative Gate Drive

• ICC = 5 mA Maximum Supply
Current

• Under Voltage Lock-Out
Protection (UVLO) with
Hysteresis

• Wide Operating VCC Range:

15 to 30 Volts

• 500 ns Maximum Switching
Speeds

• Industrial Temperature
Range:

-40°C to 100°C

• Safety and Regulatory
Approval:

UL Recognized

2500 Vrms for 1 min. per
UL1577

VDE 0884 Approved with

V

IORM

= 630 Vpeak

(Option 060 only)

CSA Approved

CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to
prevent damage and/or degradation which may be induced by ESD.

Applications

• Isolated IGBT/MOSFET
Gate Drive

• AC and Brushless DC Motor
Drives

• Industrial Inverters

• Switch Mode Power
Supplies (SMPS)

Description

The HCPL-3150 consists of a
GaAsP LED optically coupled to
an integrated circuit with a power
output stage. This optocoupler is

ideally suited for driving power
IGBTs and MOSFETs used in
motor control inverter applica­tions. The high operating voltage
range of the output stage pro­vides the drive voltages required
by gate controlled devices. The
voltage and current supplied by
this optocoupler makes it ideally
suited for directly driving IGBTs
with ratings up to 1200 V/50 A.
For IGBTs with higher ratings,
the HCPL-3120 can be used to
drive a discrete power stage
which drives the IGBT gate.

Truth Table

VCC - V

EE

VCC - V

EE

“Positive Going” “Negative-Going”

LED (i.e., Turn-On) (i.e., Turn-Off) V

O

OFF 0 - 30 V 0 - 30 V LOW

ON 0 - 11 V 0 - 9.5 V LOW
ON 11 - 13.5 V 9.5 - 12 V TRANSITION
ON 13.5 - 30 V 12 - 30 V HIGH

A 0.1 µF bypass capacitor must be connected between pins 5 and 8.

Functional Diagram

1

3

SHIELD

2

4

8

6

7

5

N/C

CATHODE

ANODE

N/C

V

CC

V

O

V

O

V

EE

5965-4780E

1-198

Ordering Information

Specify Part Number followed by Option Number (if desired)

Example

HCPL-3150#XXX

No Option = Standard DIP package, 50 per tube.
060 = VDE 0884 V

IORM

= 630 Vpeak Option, 50 per tube.
300 = Gull Wing Surface Mount Option, 50 per tube.
500 = Tape and Reel Packaging Option, 1000 per reel.

Option data sheets available. Contact Hewlett-Packard sales representative or authorized distributor.

Package Outline Drawings

Standard DIP Package

Gull-Wing Surface-Mount Option 300

9.40 (0.370)

9.90 (0.390)

PIN ONE

1.78 (0.070) MAX.

1.19 (0.047) MAX.

HP 3150 Z

YYWW

DATE CODE

0.76 (0.030)

1.40 (0.055)

2.28 (0.090)

2.80 (0.110)

0.51 (0.020) MIN.

0.65 (0.025) MAX.

4.70 (0.185) MAX.

2.92 (0.115) MIN.

6.10 (0.240)

6.60 (0.260)

0.20 (0.008)

0.33 (0.013)

5° TYP.

7.36 (0.290)

7.88 (0.310)

1

2

3

4

8

7

6

5

5678

4321

GND1

V

DD1

V

IN+

V

IN–

GND2

V

DD2

V

OUT+

V

OUT–

PIN DIAGRAM

PIN ONE

DIMENSIONS IN MILLIMETERS AND (INCHES).

* MARKING CODE LETTER FOR OPTION NUMBERS.
"V" = OPTION 060.
OPTION NUMBERS 300 AND 500 NOT MARKED.

OPTION CODE*

0.635 ± 0.25

(0.025 ± 0.010)

12° NOM.

0.20 (0.008)

0.33 (0.013)

9.65 ± 0.25

(0.380 ± 0.010)

0.635 ± 0.130

(0.025 ± 0.005)

7.62 ± 0.25

(0.300 ± 0.010)

5

6

7

8

4

3

2

1

9.65 ± 0.25

(0.380 ± 0.010)

6.350 ± 0.25

(0.250 ± 0.010)

MOLDED

1.016 (0.040)

1.194 (0.047)

1.194 (0.047)

1.778 (0.070)

9.398 (0.370)

9.906 (0.390)

4.826

(0.190)

TYP.

0.381 (0.015)

0.635 (0.025)

PAD LOCATION (FOR REFERENCE ONLY)

1.080 ± 0.320

(0.043 ± 0.013)

4.19

(0.165)

MAX.

1.780

(0.070)

MAX.

1.19

(0.047)

MAX.

2.540

(0.100)

BSC

DIMENSIONS IN MILLIMETERS (INCHES).
TOLERANCES (UNLESS OTHERWISE SPECIFIED):

LEAD COPLANARITY
MAXIMUM: 0.102 (0.004)

xx.xx = 0.01
xx.xxx = 0.005

HP 3150 Z

YYWW

1-199

VDE 0884 Insulation Characteristics (Option 060 Only)

Description Symbol Characteristic Unit

Installation classification per DIN VDE 0110/1.89, Table 1

for rated mains voltage ≤ 300 Vrms I-IV
for rated mains voltage ≤ 600 Vrms I-III

Climatic Classification 55/100/21
Pollution Degree (DIN VDE 0110/1.89) 2
Maximum Working Insulation Voltage V

IORM

630 Vpeak

Input to Output Test Voltage, Method b*

V

IORM

x 1.875 = VPR, 100% Production Test with tm = 1 sec, V

PR

1181 Vpeak

Partial discharge < 5 pC

Input to Output Test Voltage, Method a*

V

IORM

x 1.5 = VPR, Type and Sample Test, tm = 60 sec, V

PR

945 Vpeak

Partial discharge < 5 pC

Highest Allowable Overvoltage* V

IOTM

6000 Vpeak

(Transient Overvoltage t

ini

= 10 sec)

Safety-Limiting Values – Maximum Values Allowed in the Event
of a Failure, Also See Figure 37, Thermal Derating Curve.

Case Temperature T

S

175 °C

Input Current I

S, INPUT

230 mA

Output Power P

S, OUTPUT

600 mW

Insulation Resistance at TS, VIO = 500 V R

S

≥ 10

9

Ω

*Refer to the front of the optocoupler section of the current Catalog, under Product Safety Regulations section, (VDE 0884) for a
detailed description of Method a and Method b partial discharge test profiles.

Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in
application.

Regulatory Information

The HCPL-3150 has been
approved by the following
organizations:

UL

Recognized under UL 1577,
Component Recognition
Program, File E55361.

CSA

Approved under CSA Component
Acceptance Notice #5, File CA

88324.

VDE (Option 060 only)

Approved under VDE 0884/06.92
with V

IORM

= 630 Vpeak.

Reflow Temperature Profile

240

∆T = 115°C, 0.3°C/SEC

0

∆T = 100°C, 1.5°C/SEC

∆T = 145°C, 1°C/SEC

TIME – MINUTES

TEMPERATURE – °C

220
200
180
160
140
120
100

80
60
40
20

0

260

123456789101112

MAXIMUM SOLDER REFLOW THERMAL PROFILE

(NOTE: USE OF NON-CHLORINE ACTIVATED FLUXES IS RECOMMENDED.)

1-200

Recommended Operating Conditions

Parameter Symbol Min. Max. Units

Power Supply Voltage (VCC - VEE) 15 30 Volts
Input Current (ON) I

F(ON)

716mA

Input Voltage (OFF) V

F(OFF)

-3.0 0.8 V

Operating Temperature T

A

-40 100 °C

Insulation and Safety Related Specifications

Parameter Symbol Value Units Conditions

Minimum External Air Gap L(101) 7.1 mm Measured from input terminals to output
(External Clearance) terminals, shortest distance through air.

Minimum External Tracking L(102) 7.4 mm Measured from input terminals to output
(External Creepage) terminals, shortest distance path along body.

Minimum Internal Plastic Gap 0.08 mm Through insulation distance conductor to
(Internal Clearance) conductor.

Tracking Resistance CTI 200 Volts DIN IEC 112/VDE 0303 Part 1
(Comparative Tracking Index)

Isolation Group IIIa Material Group (DIN VDE 0110, 1/89, Table 1)

Option 300 - surface mount classification is Class A in accordance wtih CECC 00802.

Absolute Maximum Ratings

Parameter Symbol Min. Max. Units Note

Storage Temperature T

S

-55 125 °C

Operating Temperature T

A

-40 100 °C

Average Input Current I

F(AVG)

25 mA 1

Peak Transient Input Current I

F(TRAN)

1.0 A

(<1 µs pulse width, 300 pps)
Reverse Input Voltage V

R

5 Volts

“High” Peak Output Current I

OH(PEAK)

0.6 A 2

“Low” Peak Output Current I

OL(PEAK)

0.6 A 2
Supply Voltage (VCC - VEE) 0 35 Volts
Output Voltage V

O(PEAK)

0VCCVolts

Output Power Dissipation P

O

250 mW 3

Total Power Dissipation P

T

295 mW 4

Lead Solder Temperature 260°C for 10 sec., 1.6 mm below seating plane
Solder Reflow Temperature Profile See Package Outline Drawings Section

1-201

Electrical Specifications (DC)

Over recommended operating conditions (TA = -40 to 100°C, I

F(ON)

= 7 to 16 mA, V

F(OFF)

= -3.0 to 0.8 V,

VCC = 15 to 30 V, VEE = Ground) unless otherwise specified.

Parameter Symbol Min. Typ.* Max. Units Test Conditions Fig. Note

High Level I

OH

0.1 0.4 A VO = (VCC - 4 V) 2, 3, 5

0.5 VO = (VCC - 15 V) 2

Low Level I

OL

0.1 0.6 A VO = (VEE + 2.5 V) 5, 6 5

0.5 VO = (VEE + 15 V) 2

High Level Output V

OH

(VCC - 4) (VCC - 3) V IO = -100 mA 1, 3 6, 7

Voltage 19
Low Level Output V

OL

0.4 1.0 V IO = 100 mA 4, 6

Voltage 20
High Level I

CCH

2.5 5.0 mA Output Open, 7, 8

Supply Current IF = 7 to 16 mA
Low Level I

CCL

2.7 5.0 mA Output Open,

Supply Current VF = -3.0 to +0.8 V
Threshold Input I

FLH

2.2 5.0 mA IO = 0 mA, 9, 15,

Current Low to High VO > 5 V 21
Threshold Input V

FHL

0.8 V

Voltage High to Low
Input Forward Voltage V

F

1.2 1.5 1.8 V IF = 10 mA 16

Temperature ∆VF/∆T

A

-1.6 mV/°CIF = 10 mA

Coefficient of
Forward Voltage

Input Reverse BV

R

5VI

R

= 10 µA

Breakdown Voltage
Input Capacitance C

IN

60 pF f = 1 MHz, VF = 0 V

UVLO Threshold V

UVLO+

11.0 12.3 13.5 V VO > 5 V, 22,

V

UVLO-

9.5 10.7 12.0

UVLO Hysteresis UVLO

HYS

1.6 V

*All typical values at TA = 25°C and VCC - VEE = 30 V, unless otherwise noted.

Output Current

17

18

Output Current

IF = 10 mA 36