Honeywell TH6220D1028, TH6110D1005 Owner's Manual

Programmable
FocusPRO
Digital Thermostat
6000
User Guide
For help please visit yourhome.honeywell.com
®
Series
Thermostat controls
Function buttons
Press to select the function displayed just above each button. (Functions change depending on the task.)
Reference card
Battery holder
Hold Button
Press to override programmed temperature control
Temperature buttons
Press to set preferred temperature.
Digital display
Display screen
Low battery warning
Current inside temperature
Press the SET
button to change:
Clock: Current time. Day: Current day. Schedule: Current
thermostat program schedule.
Press the FAN
button to select:
Auto: Fan runs only
when heating or cooling system is on.
On: Fan runs continuously.
Inside
72
Wake Wed
Set Clock/Day/
Schedule
Function buttons
Press the button beneath each function to view or change settings (functions change depending on the task)
Program Schedule
Auxiliary heat (Only for heat pumps with auxiliary heat)
Replace Battery
In Recovery
6:30
Fan
Auto
AM
72
Auxiliary
System
Heat
Setting
Heat On
Temperature setting
System Status
Heat
Cool On: Cooling system is on.
Heat On: Heating system is on.
Press the SYSTEM button to select:
Heat: Heating system control.
MCR29458
Cool: Cooling system control. Off: All systems off. Auto: Thermostat
automatically selects heating or cooling depending on the indoor temperature.
Em Heat: Emergency & Auxiliary Heat control. Compressor is locked out. (Select models only.)
You can program four time periods each day, with different settings for weekdays and weekends. We recommend the pre-set settings (shown in the table below), since they can reduce your heating/cooling expenses by as much as 33%.
Wake - Set to the time you awaken and the temperature you want during the morning, until you leave for the day.
Leave - Set to the time you leave home and the temperature you want while you are away (usually an energy-saving level).
Return - Set to the time you return home and the temperature you want during the evening, until bedtime.
Sleep - Set to the time you go to bed and the temperature you want overnight (usually an energy-saving level).
NOTE: Leave and Return periods can be canceled on weekends.
Wake
(6:00 am)
Leave
(8:00 am)
Return
(6:00 pm)
Sleep
(10:00 pm)
2
Heat Cool
°
70
°
62
°
70
°
62
75 83 75 78
°
°
°
°
To adjust program schedules
1. Press SET CLOCK/DAY/SCHEDULE,
then SET SCHEDULE.
2. Press s or t to set your weekday Wake time (Mon–Fri), then press NEXT.
3. Press s or t to set the temperature for this time period, then press NEXT.
4. Set time and temperature for the next time period (Leave). Repeat steps 2 and 3 for each weekday time period.
5. Press NEXT to set weekend time periods (Sat-Sun), then press DONE to save & exit.
NOTE: Make sure the thermostat is set to the system you want to program (Heat or Cool).
NOTE: You can press CANCEL PERIOD to eliminate unwanted time periods (except Wake).
Set Clock/Day/
Schedule
Done
Mon Tue Wed Thu Fri
Leave
Done
Set Schedule
Program schedule override (temporary)
Press s or t to immediately adjust the temperature. This will temporarily override the temperature setting for the current time period.
The new temperature will be maintained only until the next programmed time period begins. For example, if you want to turn up the heat early in the morning, it will automatically be lowered later, when you leave for the day.
To cancel the temporary setting at any time, press RUN SCHEDULE.
NOTE: Make sure the thermostat is
set to the system you want to control (heat, cool or auto).
Inside
69
Run Schedule
6:30
FanSystem
Auto
FanSystem
Auto
Set Day Set Schedule
AM
8:00
CancelPeriod
Temporary
75
AM
Heat
62
Next
Heat
Setting
Cool
Heat
Setting
MCR29463
3
Program schedule override (permanent)
Press HOLD to permanently adjust the temperature. This will override the temperature settings for all time periods.
The “Hold” feature turns off the program schedule and allows you to adjust the thermostat manually, as needed.
Whatever temperature you set will be maintained 24 hours a day, until you manually change it, or press RUN SCHEDULE to cancel “Hold” and resume the programmed schedule.
NOTE: Make sure the thermostat is set
to the system you want to control (heat, cool or auto).
Inside
69
Run Schedule
AM
6:30
FanSystem
Auto
Hold
Heat
Heat
Setting
75
MCR29464
Auto changeover (heat/cool)
Auto Changeover is a feature used in climates where both air conditioning and heating are used on the same day. When the system is set to Auto, the thermostat automatically selects heating or cooling depending on the indoor temperature.
Heat and cool settings must be at least 3 degrees apart. The thermostat will automatically adjust settings to maintain this 3-degree separation (called “deadband”).
The 3-degree separation between heating and cooling set temperatures is fixed, and cannot be changed.
1. Press system button until screen displays “Auto”.
NOTE: The Auto system setting may
not appear, depending on how your thermostat was installed
Set Clock/Day/
Schedule
FanSystem
Auto
Auto
MCR29465
4
Built-in compressor protection
Damage can occur if the compressor is restarted too soon after shutdown. This feature forces the compressor to wait for a few minutes before restarting.
During the wait time, the display will flash the message Cool On (or Heat On if you have a heat pump). When the safe wait time has elapsed, the message stops flashing and the compressor turns on.
Inside
75
Set Clock/Day/
Schedule
Message flashes until safe restart time has elapsed.
AM
6:30
FanSystem
Auto
Cool
Setting
75
Cool On
Cool
MCR29466
Adaptive Intelligent Recovery™
Adaptive Intelligent Recovery eliminates guesswork when setting your schedule. It allows the thermostat to “learn” how long your furnace and air conditioner take to reach the temperature you want.
Just set your program schedule to the time you want the house to reach your desired temperature. The thermostat then turns on the heating or cooling at just the right time to reach your scheduled temperature at your scheduled time.
For example: Set the Wake time to 6 am and the temperature to 70°. The heat will come on before 6 am, so the temperature is 70° by the time you wake at 6.
Note: When Adaptive Intelligent Recovery is in effect, the thermostat will display “In Recovery”.
5
Battery replacement
Batteries are optional (to provide backup power) if your thermostat was wired to run on AC power when installed.
Install fresh batteries immediately when the REPLACE BATTERY warning begins flashing. The warning flashes about two months before the batteries are depleted.
Even if the warning does not appear, you should replace batteries once a year, or before leaving home for more than a month.
If batteries are inserted within two minutes, the time and day will not have to be reset. All other settings are permanently stored in memory, and do not require battery power.
Customer assistance
Press and pull to remove.
Replace Battery
Insert fresh AA alkaline batteries, then reinstall battery holder.
MCR29467
For assistance with this product, please visit yourhome.honeywell.com.
Or call Honeywell Customer Care toll­free at 1-800-468-1502.
Turn thermostat over to find model number and date code.
CAUTION Equipment damage hazard
To prevent possible compressor damage, do not operate cooling system when outdoor temperature is below 50°F (10°C).
Press and pull to remove.
xxxxxxx xxxxxxx
MCR29468
6
Troubleshooting
If you have difficulty with your thermostat, please try the following suggestions. Most problems can be corrected quickly and easily.
Display is blank
• Check circuit breaker and reset if necessary.
• Make sure power switch at heating & cooling system is
on.
• Make sure furnace door is closed securely.
• Make sure fresh AA alkaline batteries (depending on
model) are correctly installed (see page 6).
Heating or cooling system does not respond
Temperature settings do not change
“Cool On” or “Heat On” is flashing
To restore default settings
• Press SYSTEM button to set system Heat (see page 2). Make sure the temperature is set higher than the Inside temperature.
• Press SYSTEM button to set system to Cool (see page 2). Make sure the temperature is set lower than the Inside temperature.
• Check circuit breaker and reset if necessary.
• Make sure power switch at heating & cooling system is
on.
• Make sure furnace door is closed securely.
• Wait 5 minutes for the system to respond.
Make sure heating and cooling temperatures are set to acceptable ranges:
• Heat: 40° to 90°F (4.5° to 32°C).
• Cool: 50° to 99°F (10° to 37°C).
• Compressor protection feature is engaged. Wait 5
minutes for the system to restart safely, without damage to the compressor (see page 5).
Follow these steps to restore default settings:
1. Press SET CLOCK/DAY/SCHEDULE.
2. Press SET SCHEDULE.
3. Press DONE and NEXT at the same time for 4 seconds.
7
5-year limited warranty
Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of five (5) years from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option).
If the product is defective,
(i) return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it; or
(ii) call Honeywell Customer Care at 1-800-468-1502. Customer Care will make the determination whether the product should be returned to the following address: Honeywell Return Goods, Dock 4 MN10-3860, 1885 Douglas Dr. N., Golden Valley, MN 55422, or whether a replacement product can be sent to you.
This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Honeywell that the defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer.
Honeywell’s sole responsibility shall be to repair or replace the product within the terms stated above. HONEYWELL SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE FIVE-YEAR DURATION OF THIS WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
If you have any questions concerning this warranty, please write Honeywell Customer Relations, 1985 Douglas Dr, Golden Valley, MN 55422 or call 1-800-468-1502. In Canada, write Retail Products ON15-02H, Honeywell Limited/Honeywell Limitée, 35 Dynamic Drive, Toronto, Ontario M1V4Z9.
Automation and Control Solutions
Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 yourhome.honeywell.com
® U.S. Registered Trademark. © 2013 Honeywell International Inc. 69-1921EFS—05 M.S. Rev. 10-13 Printed in U.S.A.
69-1921EFS-05
Loading...
+ 16 hidden pages