Honeywell CX80-NB, CX80-CB, CX80 Quad Battery Charger Quick Start Manual

CX80 ChargeBase and NetBase

Model CX80-CB, CX80-NB

Quick Start Guide

CX80-CNB-EN-QS Rev A

04/18

Out of the Box

Make sure that your shipping box contains these items:

• CX80 ChargeBase (CX80-CB) or NetBase (CX80-NB)

• Power supply

• Power cord (US Only)

• Regulatory Sheet

If any of these items are missing or appear damaged, contact
your Customer Account Representative. Keep the original pack­aging in the event that you need to return the ChargeBase or
NetBase for service or if you want to store the charger while not
in use.

Caution: We recommend the use of Honeywell
accessories and power adapters. Use of any non­Honeywell accessories or power adapters may cause
damage not covered by the warranty.

Mise en garde : Il est recommandé d'utiliser les
périphériques, les cordons d'alimentation et les
adaptateurs secteur conçus par Honeywell. L'utilisation
de tout périphérique, cordon d'alimentation ou
adaptateur secteur d'une autre marque est susceptible
de provoquer des dommages non couverts par la
garantie.

1

Connect Power

Power Connector

Ethernet
(CX80-NB)

Use only a UL Listed power supply which has been qualified by
Honeywell with an output rated at 12 V / 8.5 A. The power supply
input rating is 100-240 VAC, 50/60 Hz. The operating tempera­ture is -10 °C to 50 °C (14 °F to 122 °F). The maximum output
for the terminal is 9VDC/2A.

1. Plug the power cord into the power supply.

2. Plug the power supply cable into the power connector on the back of the charger.

3. Plug the power cord into a standard wall outlet.

2

Charge the Battery Pack

Caution: Make sure that all components are dry prior to
using the computers and batteries with accessories. Using
wet components may cause damage not covered by the
warranty.

Mise en garde : Assurez-vous que tous les composants sont
secs avant de connecter les terminaux/batteries à des
périphériques. L'insertion de composants humides risque
de provoquer des dommages non couverts par la garantie.

• Insert one to four CX80s with battery packs inserted into the

ChargeBase or NetBase.

3

Mount the ChargeBase or NetBase

You can mount the charger on a flat, horizontal surface such as
a desktop or workbench with an optional DIN rail.

Mounting hardware required:

•DIN rail

• 3/16-inch diameter x 5/8-inch long pan head screw

• 1/2-inch OD x 7/32-inch ID x 3/64-inch thick washer

• 3/16-inch diameter nut

1. Slide the DIN rail into the slot on the bottom of the Charge­Base or NetBase.

2. Secure the DIN rail to the flat surface with the hardware.

4

Support

To search our knowledge base for a solution or log into the Tech­nical Support portal and report a problem, go to

www.hsmcontactsupport.com.

User Documentation

For the user guide and other documentation, go to

www.honeywellaidc.com.

Limited Warranty

For warranty information, go to www.honeywellaidc.com and
click Resources > Warranty.

Patents

For patent information, see www.hsmpats.com.

Disclaimer

Honeywell International Inc. (“HII”) reserves the right to make
changes in specifications and other information contained in
this document without prior notice, and the reader should in all
cases consult HII to determine whether any such changes have
been made. The information in this publication does not repre­sent a commitment on the part of HII.

HII shall not be liable for technical or editorial errors or omis­sions contained herein; nor for incidental or consequential
damages resulting from the furnishing, performance, or use of
this material. HII disclaims all responsibility for the selection
and use of software and/or hardware to achieve intended
results.

5

This document contains proprietary information that is pro­tected by copyright. All rights are reserved. No part of this docu­ment may be photocopied, reproduced, or translated into
another language without the prior written consent of HII.

Copyright © 2018 Honeywell International Inc. All rights
reserved.

6