Honeywell CTS-V SERIES, CTP-V SERIES Installation Instructions

Solid and Split Core 0-5/10Vdc

Output Current Sensors

CTS-V AND CTP-V SERIES

		INSTALLATION INSTRUCTIONS
	APPLICATION	densing
		Operating Humidity Range: 0 to 95%, non-con-
	The 0-5/10Vdc Output Solid and Split Core Current	Storage Temperature: 41 to 95°F (5 to 35°C)
	Sensors are designed for use in any AC current	RH Range: 40% to 85% RH, non-condensing
	monitoring application in which you are looking to
		Wire Recommendations: 2 Conductor (Shielded
	monitor a particular piece of equipment.
		Cable)
	SPECIFICATIONS	Wire Size:
		18 to 24 AWG (0.823 mm2 to 0.205 mm) Copper
		Wires only

Monitored Current Type: AC Current

Maximum AC Voltage: 600 VAC

Isolation Voltage: 2200 VAC

Supply Voltage:

Induced from the Monitored Conductor (Insulated Conductors only)

150-Amp Sensors: 0 to 10 VDC

Operating Temperature Range: 5 to 104ºF (-15 to 40ºC)

Terminal Block Torque Rating: 4.43 to 5.31 in-lbs. (0.5 to 0.6 Nm)

Minimum Mounting Distance:

1” (2.6 cm) between current sensor & other magnetic devices (Relays, Contactors, Transformers)

Agency Approvals:

UL/CUL US Listed (UL 508) Ind. Control Equipment (File # E309723), CE, RoHS2, WEEE

STANDARD ORDERING

Table 1. Standard Ordering.

						Output
Model #	Selectable Ranges	Measurement	AC Waveform	Solid-Core	Split-Core	Signal
CTS-V-50	0 to 10/20/50A	Average	Pure Sinusoidal	•		0 to 5 VDC
CTS-V-150	0 to 50/100/150	Average	Pure Sinusoidal	•		0 to 10 VDC
CTP-V-50	0 to 10/20/50A	Average	Pure Sinusoidal		•	0 to 10 VDC
CTP-V-150	0 to 50/100/150	Average	Pure Sinusoidal		•	0 to 10 VDC

WARNING	WARNING
This product is not intended to be used for	Electrical shock hazard.
Life or Safety applications.	Disconnect and lock out all power sources
This product is not intended for use in any	before installation as severe injury or death
hazardous or classified locations. The CTS-V	may result from electrical shock due to
and CTP-V Series Current Sensors must be	contact with high voltage wires.
used on Insulated Conductors Only!

20

31-00144-02

SOLID AND SPLIT CORE 0-5/10VDC OUTPUT CURRENT SENSORS

INSTALLATION

Make sure that all installations are in compliance with all national and local electrical codes. Only qualified individuals that are familiar with codes, standards, and proper safety procedures for high-voltage installations should attempt installation. The current sensor will not require external power, since the power for the current sensor is induced from the conductor being monitored.

The current sensor may be mounted in any position using the two #8 x ¾” Tek screws and the mounting holes in the base, or snapped directly on to the 35mm DIN rail (See Fig. 1). Leave a minimum distance of 1” (3 cm) between the current sensor and any other magnetic devices such as contactors and transformers.

<![if ! IE]>

<![endif]>–

+

M37377

Fig. 1. Sensor Placed on Rail.

Latch Operation for CTP-V Series

Press down on the side tab and swing the top of the unit up to open the split core current sensor as shown in Figure 2. Press down firmly on the cover to close the current sensor. An audible “click” will be heard as the tab slides over the tongue on the base.

CAUTION

Mating surfaces of the magnetic core are exposed when the sensor is open.

Electrical contact grease, present on the cores to prevent corrosion, can capture grit and dirt if care is not exercised. Operation can be impaired if anything prevents good contact between pole pieces. Visually check the mating parts of the core before closing the current sensor.

M37359

Fig. 2. Opening CTP-V Series.

Current Sensor Setup

The amperage range selected represents the maximum current that can be applied to the conductor being monitored, Do not exceed! All current sensors with selectable ranges will have the range selection jumper factory set on the high range. For models with field selectable amperage ranges, select the correct amperage range using the range selection jumper.

WIRING

We recommend the use of a two conductor 16 to 22 AWG shielded cable, copper wire only, for all Analog current sensor installations. A maximum wire length of less than 30 meters (98.4 feet) should be used between the current sensors and the Building Management System or controller.

31-00144—02

2