Hobart MG1532 General Manual
Item # _____________________________________
Quantity ___________________________________
C.S.I. Section 11400
MG1532
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
STANDARD FEATURES
■ 150 pound hopper capacity
■ Double wall construction
■ 7.5 H.P. grind motor and 1 H.P. mix motor
■ 8-foot cord and plug power connection
■ Separate mix and grind motors
■ Pneumatic foot control
■ Hand removable and interchangeable seals
■ Counterbalanced lid
■ Double-sealed push button control panel with
condensate heater
■ Easy access hopper interior and exterior
surfaces
MIXER-GRINDER
MODEL
❑ MG1532 – Mixer-Grinder
Specications, Details and Dimensions on Reverse Side.
ACCESSORIES
❑ #32 knives and plates
MG1532 MIXER-GRINDER
F-39599 – MG1532 Mixer-Grinder Page 1 of 2
MG1532
MIXER-GRINDER
SPECIFICATIONS
GENERAL: The MG1532 has a 7.5 H.P. grind motor, 1H.P. mix
motor and an 8-foot length cord and plug power connection.
Casters, air-drive foot switch, drain pan and splash shield are
standard. Available voltages are 208/60/3, 240/60/3 and 480/60/3.
ELECTRICAL CONTROLS: Electrical controls consist of front
mounted water resistant switches, magnetic contactors, dual
motor overload protection and foot switch operation capability.
An electrical interlock switch is provided. Whenever the hopper lid
is opened, power to the motors is shut off. The hopper lid must be
in its proper operating position before the motors can be started.
CAPACI TY: The MG1532 Mixer-Grinder hopper has meat
capacity up to 150 pounds depending on the type of product.
The grinding rate is 55 to 60 pounds of fresh boneless beef
per minute, rst or second cutting through a 1⁄8" plate; 60 to 65
pounds of pork per minute second cutting through a 3⁄16" plate.
The MG1532 is for fresh or frozen meat tempered to 26 deg. F.
or higher and can be in ake or stick form.
GRINDING END: The mixer-grinder is equipped with a “Wedge
cylinder” grinding end. This grinding end is sized for #32 knives
and plates (not included but optionally available).
FEEDING SYSTEM: The MG1532 is powered by two separate
drive systems. A 1 H.P. motor drives the heavy-duty steel mixing
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
arm. The arm rotates at 23 rpm and can easily be removed from
the hopper for cleaning. The conveyor screw extends the full
length of the hopper and cylinder. The screw rotates at a speed
of 216 rpm. By depressing the MIX/GRIND START button both the
mixing arm and the screw are operated. Both mixing and grinding
are stopped when the STOP switch is depressed.
CLEANING: The mixing arm, conveyor screw, cylinder, and
conveyor screw drive-shaft seal and mix arm seal are removable
from the mixer-grinder for cleaning.
SPECIAL EQUIPMENT: When the MG1532 is used with a side
feed as a second cut machine, an adapter ring is required to
attach to Hobart grinders, and special adapters are required to
attach to other makes. When ordering a side-feed adapter for
non-Hobart grinders, specify knife and plate size. When ordering an adapter ring for a Hobart grinder, specify grinder model
nu mber.
FINISH: The mixer-grinder consists of glass bead nished stainless steel hopper, stainless steel panels to enclose the base
assembly and motors. The end ring and cylinder are stainless
steel. The mixing arm and conveyor screw are tinned. The casters
are stainless steel and nickel-chrome plated.
DETAILS AND DIMENSIONS
As continued product improvement is a policy of Hobart, specications are subject to change without notice.
Page 2 of 2 F-39599 – MG1532 Mixer-Grinder
F-39599 (REV. 01/12) LITHO IN U.S.A. (H-01)
Loading...