Item # _____________________________________
Quantity ___________________________________
C.S.I. Section 11400
LXi
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
STANDARD FEATURES
■ 30 racks per hour
■ .74 gallons of water per rack
■ Hot water or chemical sanitation units available
■ Low chemical alert indicator (on machines
ordered with pumps, standard on chemical
machine)
■ Sense-A-Temp™ booster heater capable of
70° rise, provided on LXiH models
■ Delime notification with cycle
■ Chemical pump “auto-prime”
■ Service diagnostics
■ 16 gauge stainless steel tank
■ Microcomputer, top mounted controls with
digital cycle/temperature display
DISHMACHINE
OPTIONS AT EXTRA COST
❑ 208-240(2W)/60/1
❑ Detergent and rinse aid pumps
ACCESSORIES
❑ Power cord kits
❑ Stainless steel base with 6" legs
❑ 17" stainless steel stand
❑ Pressure regulator valve
❑ Trim kit, top cover
❑ Rolled top, dish rack holder
❑ DWT2 drain water tempering kit
Specifications, Details and Dimensions on Inside and Back.
■ Revolving upper and lower anti-clogging
wash arms
■ Revolving upper and lower rinse arms
■ Removable stainless steel scrap screen
■ Corrosion resistant pump
■ Automatic pumped drain
■ 17" door opening
■ Automatic fill
■ Labyrinth-type door seal
■ Electric tank heat
■ Two dishracks – one peg and one combination-
type
STANDARD VOLTAGES
❑ 120/60/1 (LXiC model only)
❑ 120/208-240(3W)/60/1
LXi DISHMACHINE
F-8193 – LXi Dishmachine Page 1 of 4
LXi
DISHMACHINE
WARNING:
REQUIRED FLOWING WATER PRESSURE TO THE DISHMACHINE IS
20 ± 5 PSIG. IF PRESSURES HIGHER THAN 25 PSIG ARE PRESENT, A
PRESSURE REGULATING VALVE MUST BE INSTALLED IN THE WATER
LINE TO THE DISHMACHINE (BY OTHERS).
IMPORTANT: THE SODIUM HYPOCHLORITE (LIQUID BLEACH) CONTAINER SHOULD BE PLACED NO HIGHER THAN 10" ABOVE FLOOR.
IF BLEACH CONTAINER IS TO BE PLACED IN CABINET ADJACENT
TO MACHINE, A 1/2" DIA. HOLE IS REQUIRED IN THE CABINET TO
RUN BLEACH SUPPLY LINE.
USE ONLY 6% S ODIUM HYPOCHLORITE (LI QUID BLEACH) AS
SANITIZING CHEMICAL TO INSURE PROPER OPERATION OF DISHMACHINE. IF 8.4% IS TO BE UTILIZED CONTACT HOBART SERVICE
TO CHANGE THE SANITIZER PUMP SETTINGS.
DO NOT PRE-MIX RINSE AGENT AND SODIUM HYPOCHLORITE
(LIQUID BLEACH).
CERTAIN MATERIALS INCLUDING SILVER PLATE, ALUMINUM AND
PEWTER ARE ATTACK ED BY SODIU M HYPOCHLOR ITE (LIQUID
BLEACH). SEE INSTRUCTIONAL MANUAL.
STEAM GENERATED FROM NORMAL OPERATION MAY ESCAPE FROM
THE DOOR. WOOD LAMINATE, VENEERS, ETC. ARE UNSUITABLE
MATERIALS FOR USE IN AREAS EXPOSED TO DISHWASHER STEAM
AND DETE RGENTS. STAINLESS S TEEL OR OTHER MOI STURERESISTANT SHIELDS ARE RECOMMENDED FOR SURFACES ADJACENT
TO LXi SIDES AND TOP.
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
NOTES:
1. ALL VERTICAL MACHINE DIMENSIONS TAKEN FROM FLOOR MAY
BE INCREASED BY 1".
2. MOIST AIR ESCAPES FROM THE DOOR.
USE ONLY MOISTURE RESISTANT MATERIALS ADJACENT TO LX
SIDES AND TOP.
3. A VENT HOOD IS NOT RECOMMENDED ABOVE THE LX
DERCOUNTER DISHWASHER S INCE IT DOES NOT PRODUCE
EXCESSIVE VAPORS
PLUMBING NOTES:
1. WATER HAMMER ARRESTOR (MEETING ASSE-1010 STANDARD
OR EQUIVALENT) TO BE SUPPLIED (BY OTHERS) IN COMMON
WATER SUPPLY LINE AT SERVICE CONNECTION.
2. RECOMMENDED WATER HARDNESS TO BE 4-6 GRAINS FOR
BEST RESULTS.
3. MI NIMUM W ATER CONDU CTIVI TY RE QU IRED - 30 MICRO MHOS/CM.
4. IF DRAIN HOSE IS LOOPED ABOVE A SINK, THE LOOP MUST NOT
EXCEED 38" AFF.
i
i UN-
MACHINE TYPE &
SPECIFICATION
LXiC (120/60/1)
USE 90°C STRANDED
COPPER WIRE ONLY.
LXiC (120/208-240(3W)/60/1*)
LXiC (208-240/60/1)
USE 90°C STRANDED
COPPER WIRE ONLY.
LXiH (120/208-240(3W)/60/1*)
LXiH (208-240/60/1)
USE 90°C STRANDED
COPPER WIRE ONLY.
ELECTRICAL OPTIONS BELOW ARE NON STANDARD VOLTAGES AVAILABLE
AT EXTRA COST. CONSULT FACTORY FOR PRICING AND LEAD TIME.
LXiH 208-240/60/3
480/60/3
220-240/50/1
380-400/60/3
RATED
AMPS
15.4 20 20
13.6 20 20
37.7 50 50
29.5
14.8
38.1
17.1
MIN SUPPLY
CKT CONDUCT
AMPACITY
35
20
50
25
MAX
PROTECTIVE
DEVICES
35
20
50
25
CONNECTION INFORMATION
(AFF = ABOVE FINISHED FLOOR)
LEGEND
E1 ELECTRICAL CONNECTION: 1-3/8" DIA. HOLE
FOR 1" TRADE SIZE CONDUIT; 31-3/4" AFF.
P1 SINGLE FILL AND RINSE CONNECTION:
3/4" FEMALE GARDEN HOSE FITTING ON 6' LONG
HOSE SUPPLIED WITH MACHINE; 140°F WATER
MIN. FOR LXiC, 110°F WATER MIN. FOR LXiH,
1-1/2" AFF.
P2 DRAIN CONNECTION: 3/4" MPT FITTING WITH
6' LONG HOSE SUPPLIED WITH MACHINE;
3-9/16" AFF.
Page 2 of 4 F-8193 – LXi Dishmachine
LXi
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
DISHMACHINE
* THIS SYSTEM REQUIRES THREE POWER WIRES WHICH INCLUDES
A CURRENT CARRYING NEUTRAL, AN ADDITIONAL FOURTH WIRE
MUST BE PROVIDED FOR MACHINE GROUND.
ACCESSORY CORD KITS AVAILABLE FOR ALL MACHINES
SHIPPING WEIGHTS (LBS) LXiC LXiH
NET WEIGHT OF MACHINE 190 lbs. 210 lbs.
DOMESTIC SHIPPING WEIGHT 235 lbs. 255 lbs.
ELECTRICAL AND GROUNDING CONNECTIONS
MUST COMPLY WITH THE APPLICABLE PORTIONS
OF THE NATIONAL ELECTRICAL CODE AND/OR
OTHER LOCAL ELECTRICAL CODES.
PLUMBING CONNECTIONS MUST COMPLY WITH
APPLICABLE SANITARY, SAFETY AND PLUMBING
CODES. DRAIN AND FILL LINE CONFIGURATIONS
VARY, SOME METHODS ARE SHOWN ON THIS DRAWING.
WARNING
MODELS:
LX
iC, LXiH
892882
F-8193 – LXi Dishmachine Page 3 of 4
Printed On Recycled Paper
LXi
DISHMACHINE
SPECIFICATIONS
DESIGN: Front opening, equipped for installation of both
freestanding and undercounter-type operations.
CONSTRUCTION: 304 series stainless steel tank, door
and top panel.
PUMP: Centrifugal-type, integral with motor, horizontally
mounted. Pump capacity 54 gpm.
MOTOR: Single phase, split-phase type,furnished for
120/60/1 or 208-240/60/1 electrical specification. Factory
sealed lubrication. Inherent overload protection with auto
reset. Also available with three phase motors at extra cost.
WASH AND RINSE CYCLE: Complete automatic type,
controlled by solid-state electronics. Cycle may be
interrupted any time by opening door. Cycle continues
when door is closed.
• Initial cycle fills wash tank, to be recirculated each
wash cycle. Some wash water is drained off before
rinse cycle. Rinse cycle refreshes wash water and tank
heat.
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
RINSE AND SANITATION:
• LXiH: Sanitation is accomplished by means of a built-in
booster heater designed to raise temperature of water
to a minimum of 180°F from an incoming water temperature of 110°F.
• LXiC: Sanitation is accomplished by injection of proper
amount of sodium hypochlorite solution (liquid bleach)
into final rinse water to achieve a minimum of 50PPM
sanitizing solution. Injection of sodium hypochlorite is
accomplished by a built-in sanitizing chemical pump.
PUMPED DRAIN: Machine automatically drains water
through a built-in pump. Maximum 38" drain height
permitted.
RACKING:
Machines accommodate racks from 10" x 20"
to 20" x 20". Also accepts 16" x 18" cafeteria trays.
CAUTION: Certain materials, including silver, aluminum
and pewter are attacked by Sodium Hypochlorite solution
in the chemical sanitizing mode of operation.
SPECIFICATIONS: Listed by Underwriters Laboratories
Inc. and NSF International.
MACHINE RATINGS LXiC LXiH
Racks per Hour Rate 30
Dishes per Hour (25 per Rack Avg.) 750
Glasses per Hour (36 per Rack Avg.) 1080
Controls Microcomputer
Tank Capacity - Gallons
Overall Dimensions - H x W x D 33
Cycle Time - Minutes
Tank Heat 1.5 KW
Electric Booster Heater N/A 6 KW
Water Usage Per Rack - Gallons .74
Drain Design Pumped
Door Opening Height 17"
Chemical Connection Capability Standard
Detergent Pump Optional
Rinse-Aid Pump Optional (W/Det Pump)
Sanitizer Pump Standard N/A
Chemical Prime (auto prime) Standard
Peak Drain Flow - GPM
Service Diagnostics Standard
70° Rise Sense-A-Temp
™
Booster Heater N/A Standard
3
3
⁄4" x 2315⁄16" x 263⁄4"
2
4
As continued product improvement is a policy of Hobart, specifications are subject to change without notice.
Page 4 of 4 F-8193 – LXi Dishmachine
F-8193 (REV. 10/07) LITHO IN U.S.A. (H-01)
Loading...