I
N
S
T
R
FP300 FOOD PROCESSOR
MODEL FP300 ML-104495
U
C
T
I
MODEL FP300
FOOD PROCESSOR
O
N
S
701 S. RIDGE AVENUE
TROY, OHIO 45374-0001
FORM 19157 Rev. B (11-98)
Installation, Operation, and Care of
MODEL FP300
FOOD PROCESSOR
SAVE THESE INSTRUCTIONS
GENERAL
The FP300 Food Processor is used for slicing, shredding, grating, Julienne cutting and dicing
vegetables, fruits, or cheese. The compact unit is designed for ease of operation and quick cleaning.
A Work Table, a Wall Rack, and a wide range of slicer, shredder, and dicing plates are available
options.
INSTALLATION
UNPACKING
Immediately after unpacking the FP300, check for possible shipping damage. If the Food Processor
is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery.
Prior to installation, test the electrical service to assure that it agrees with the specifications on the data
plate located at the rear.
Do not lift the unit with any hinged or extended parts; lift only with one hand under the protruding lip
at the rear near the base of the motor compartment and the other hand underneath the chute.
LOCATION
The FP300 should be operated on a suitable counter height surface. A pan (not provided), suitable for
kitchen use, can be used to capture the product at the exit chute.
© HOBART CORPORATION, 1994
– 2 –
ELECTRICAL CONNECTION
WARNING: THE ELECTRICAL CORD HAS A THREE-PRONGED GROUNDING PLUG WHICH
MUST BE CONNECTED TO A PROPERLY GROUNDED RECEPTACLE. IF THE RECEPTACLE IS
NOT THE PROPER GROUNDING TYPE, CONTACT AN ELECTRICIAN. DO NOT REMOVE THE
GROUNDING PRONG FROM THE PLUG.
ELECTRICAL DATA
Model Volts / Hz / Phase Amps
FP300 120 / 60 / 1 10
OPERATION
WARNING: ROTATING KNIVES INSIDE. ALWAYS USE PUSHER PLATE. KEEP HANDS OUT.
Proper assembly of the FP300 including selection of the appropriate cutters is necessary for correct
operation of the food processor (Figs. 1 & 2). Refer to the Cutting Tool Guide for sizes of cutters and
refer to the appropriate operation instructions.
CONTROLS
START (Green) — Push to start.
STOP (Red) — Push to stop.
Interlock switches prevent the machine from operating when the feed hopper is out of position or the
pusher plate is raised above the feed hopper. If these features do not function as described, contact
your local Hobart service office.
During operation, when the pusher plate is fully raised above the feed hopper, the machine stops and
allows the pusher plate to be rotated counterclockwise for loading. To continue operation, rotate the
pusher plate clockwise until it is directly above the feed hopper; as the pusher plate begins to lower
into the hopper, the machine will restart — you do not need to push the green START switch unless
STOP was pressed.
Always push the red STOP switch before changing cutters or cleaning.
– 3 –
Operations with a Single Plate — (Fig. 1)
SLICING, SHREDDING, GRATING, AND JULIENNE CUTTING
1. Raise the pusher plate using the pistol grip handle
and turn it to the left.
2. Release the feed hopper lock by turning the finger
paddle counterclockwise. Then raise the feed hopper.
3. Lower the flinger plate on the knife shaft until the
flinger plate seats on the shaft pin.
4. Select the appropriate plate for the job. Place the
plate on the shaft, turning until engaged.
5. Lower the feed hopper. NOTE: When the pusher
plate is rotated and lowered, the feed hopper will
automatically be locked.
Fig. 1
Operations with Two Plates — (Fig. 2)
DICING AND FRENCH FRIES
1. Raise the pusher plate and turn it to the left.
2. Release the feed hopper lock by turning the finger
paddle counterclockwise. Then raise the feed hopper.
3. Lower the flinger plate on the knife shaft until the
flinger plate seats on the shaft pin.
4. Select the proper size dicing plate and place it
correctly on the knife shaft above the flinger plate.
Select the appropriate slicing plate for the job (see
Cutting Tool Guide). Place the slicing plate on the
shaft, turning until engaged.
5. Lower the feed hopper. NOTE: When the pusher
plate is rotated and lowered, the feed hopper will
automatically be locked.
Fig. 2
– 4 –
USING THE FEED HOPPER
After the pusher plate is raised, pre-pared products, such as potatoes, carrots, onions, lettuce,
cabbage, etc. can be placed in the large feed hopper.
When cutting French fries with the Julienne cutter, position the potatoes at the lower-right corner of the
large feed hopper. The potatoes may be stacked to cut several at one time. NOTE: For consistent
results, stack product in the lower-right corner of the feed hopper, one pile only.
The large feed hopper is also used to slice round products, such as lemons and tomatoes. Position
the product in the lower-right corner of the feed hopper. NOTE: For best results, it is advisable to
remove tops and tails from products like lemons, limes, or onions and place them in the hopper
perpendicular to the desired cut.
USING THE FEED TUBE
Twist the knob to release the catch on the feed tube pusher and pull out to expose the feed tube
opening.
The feed tube is used for slicing long, thin shaped products, such as cucumbers or carrots or to contain
small items like radishes. The machine does not stop when the feed tube pusher is removed; this
allows products to be processed continuously. Always use the feed tube pusher.
CLEANING
WARNING: TURN THE MACHINE OFF AND UNPLUG THE ELECTRICAL CORD BEFORE CLEANING.
Clean the machine immediately after each use. Dismantle all removable parts from the machine and
wash them in warm water and detergent. Rinse thoroughly and wipe dry with a soft clean cloth.
NOTE: Allowing food juices to dry on the machine may cause discoloration. NEVER clean feed
hopper, cutting tools or other aluminum parts in highly alkaline dishwashing solutions or in excessively
hot water as this can cause formation of aluminum oxide (black). DO NOT USE steel wool or sharp
objects for cleaning machine surfaces if they become discolored; scratched surfaces become hard to
keep clean.
1. Remove feed tube pusher and rinse in luke warm water. Raise the pusher plate; turn it to the left.
2. Remove the feed hopper and rinse it in luke warm water.
3. Lift out the cutting plate. If you have used the dicing grid, push the remaining leftovers through the
grid with the nylon brush before removing.
4. Remove the dicing plate and flinger plate; rinse in luke warm water.
5. Turn the pusher plate back clockwise over the feed hopper and lower it.
6. Place a pan under the exit chute and pour luke warm water from the top through the knife chamber.
Run a wet cloth through the feed tube. Wipe with a clean dry cloth.
7. Return the cutting tools to the wall rack. Lower the flinger plate onto the knife shaft until the flinger
plate seats on the shaft pin.
8. Place the feed hopper on the hinge pins and lower to normal position. Turn the lower pusher plate.
Replace the feed tube pusher.
– 5 –
CUTTING TOOLS Fractional sizes are in inches (millimeters are in parentheses).
Slicers Use Fine and Standard Slicers for sliced products and for dicing.
Soft products like tomato use the FINE SLICER not the STANDARD SLICER.
FINE SLICER 1/16 (1.5MM)
FINE SLICER 1/8 (3MM)
FINE SLICER 5/32 (4MM)
FINE SLICER 7/32 (6MM)
FINE SLICER 3/8 (10MM)
STANDARD SLICER 3/8 (10MM) HD
FINE SLICER 9/16 (14MM)
Crimping Slicer Ripple cuts root vegetables (beets, potatoes, carrots, etc).
CRIMPING SLICER 3/16 CR (4.5MM)
Julienne Cutters
JULIENNE CUTTER 3/32 (2.5MM)
JULIENNE CUTTER 3/16 (4.5MM)
JULIENNE CUTTER 7/32 (6MM)
JULIENNE CUTTER 3/8 (10MM)
– 6 –
Dicer and French Fry Plates
The recommended slicer plate will produce near-cube shaped products.
The DICER grid dimension must be equal to or larger than the SLICER dimension.
DICER 9/32 Use with FINE SLICER 7/32 *
DICER 3/8 Use with STANDARD SLICER 3/8 *
DICER 1/2 Use with STANDARD SLICER 3/8 *
DICER 5/8 Use with STANDARD SLICER 3/8 *
DICER 3/4 Use with FINE SLICER 9/16
FRENCH FRY3/8 Use with STANDARD SLICER 3/8
* Soft products may be diced with thinner slicer blades than those recommended.
Graters and Shredders
FINE GRATER Grates raw potato for potato pancakes, horseradish (sauce), dry
bread, hard "Parmesan" cheese.
SHREDDER 1/16 (1.5MM) Grates carrots, dry bread, almonds, nuts.
SHREDDER 3/32 (2MM) Grates carrots, dry bread, almonds, nuts.
SHREDDER 1/8 (3MM) Grates carrots, dry bread, almonds, nuts.
SHREDDER 3/16 (4.5MM) Grates carrots, dry bread, almonds, nuts, soft pizza
cheese.
SHREDDER 7/32 (6MM) Grates carrots, dry bread, almonds, nuts, soft pizza
cheese.
SHREDDER 5/16 (8MM) Grates carrots, dry bread, almonds, nuts, soft pizza
cheese, shreds cabbage.
– 7 –
MAINTENANCE
WARNING: TURN THE MACHINE OFF AND UNPLUG THE ELECTRICAL CORD BEFORE DOING
ANY MAINTENANCE.
Routinely inspect the machine to assure that it is in proper working order. Plates must be clean, intact
and sharp.
The pusher plate shaft should be regularly lubricated with a drop of mineral oil, NOT COOKING OIL.
REPLACEMENT DICING GRIDS
Depending on usage, dicing grids become dull from wear with an average life expectancy from
8 – 18 months. Dicing grids cannot be resharpened and are therefore expendable. Replacement dicing
grids are available from your local Hobart Service office.
TROUBLESHOOTING
SYMPTOM POSSIBLE CAUSE SUGGESTED ACTION
Motor won't start. A. Feed hopper not locked in Make sure feed hopper is
correct position. locked correctly.
B. Pusher plate raised. Turn pusher plate clockwise
and lower it.
C. Fuse or circuit breaker Have electrician check circuit.
interrupting power.
Machine stops while A. See B and C above.
operating and won't restart.
B. Motor is overloaded and Allow the motor to cool; motor
motor is too warm. protector will allow restart
when it has cooled.
Low output or bad A. Wrong cutting plates Refer to CUTTING TOOL GUIDE.
cutting results. were used.
B. Slicing, shredding, Make sure plates are intact
dicing, or Julienne and sharp.
cutting plate is NOT OK.
C. Feeding pressure A light feeding pressure is best
excessive. for most products.
SERVICE
Contact your local Hobart Service Office for any repairs or adjustments needed on this equipment.
Long-term service contracts are available on this and other Hobart products.
FORM 19157 Rev. B (11-98) PRINTED IN U.S.A.
– 8 –
Loading...