Hobart FD500 User Manual

Item # _____________________________________
R
Quantity ___________________________________
C.S.I. Section 11400
FD500
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
Peak periods for the large food service establish­ment can be very demanding on any foodwaste disposer. This powerful disposer has a large capacity for foodwaste. Hobart has engineered the 5 horsepower unit to perform dependably during peak demands for economical foodwaste disposal.
SPECIFICATIONS
Listed by Underwriters Laboratories Inc. and meets requirements of A.S.S.E. Standard No. 1009. (50 Hz. Electrical Specifications not available with thermal overload protection nor submitted for UL listing.)
MOTORS: Continuous duty rating. Permanently lubricated bearings (matched set double row tapered roller bearings for upper shaft thrust support, ball bearings for lower shaft support). Inherent overload protection in motor.
HOUSINGS: Heavy aluminum grind and discharge housings. Eight bolts fasten the motor unit to the grind chamber, permit easy removal.
FOODWASTE DISPOSERS
MOTOR SHAFT SEAL: Face-type seal consists of
sintered bronze mating ring and spring loaded carbon ring insert in chemical resistant neoprene bellows. Mating surfaces are protected from grit of fibers by being recessed into flywheel. Should any moisture pass this seal, a flinger and drain tube are provided to insure immediate removal. In addition, a lip-type oil seal (located beneath the bearings) is an “added protection” water seal.
DRAIN CONNECTOR: The removable outlet flange is tapped for 3" pipe connection.
DUAL DIRECTION GRINDING: Disposer flywheel operates in either direction. When installed with Control Groups 2 & 3, flywheel automatically starts in opposite direction each start. (Increases life and efficiency of grinding elements and frees flywheel of jams.)
MOUNTING: Disposer fastens to 7" I.D. throat opening cones. A vinyl isolating ring eliminates metal-to-metal contact at the cone mounting, reduces vibration and noise transmission.
STATIONARY SHREDDER RING: Ni-Hard, 2 high, 4 machine ground primary action breaker bars, 42 secondary action grinding teeth.
FLYWHEEL: Breaker blade, mounted at center, speeds grinding, prevents objects from “riding” at center. Two hardened stainless steel cutter blocks (fastened to flywheel with Nyloc screws) are replaceable, can be indexed for new cutting edges. Ni-Resist flywheel is 9" diameter, slots undercut the hredder ring to assure that particles are cut to proper size before passing to the drain line.
1
2"
FD500 FOODWASTE DISPOSERS
F-8391 – FD500 Foodwaste Disposers Page 1 of 4
FD500 FOODWASTE DISPOSERS
ACCESSORY GROUPS
GROUP A
Nitrile Rubber Scrapping Ring
Stainless Steel Silver-Saver Sleeve with Side Feed Hole
15" or 18" Cone
Water Swirl Vacuum Breaker
GROUP B
Nitrile Rubber Silver-Saver Splash Guard Ring
15" or 18" Cone
GROUP D
Nitrile Rubber Silver-Saver Splash Guard Ring
7" I.D. Stainless Steel Weld-in Adapter for Sink
Fixed Direction Vacuum Breaker Water Inlet for Sink
ACCESSORY COMPONENTS
CONES-SINK—Stainless Steel
Part No.
Cone 15" I.D. w/hole for water swirl
inlet .....................................ML-32664
Cone 18" I.D. w/hole for water swirl
inlet .....................................ML-32666
Cone 15" I.D. w/out swirl hole .... 315144
Cone 18" I.D. w/out swirl hole .... 315146
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
CONE FEEDING ACCESSORIES
Part No.
Nitrile Rubber Scrapping Ring .... 292122
Stainless Steel Silver-Saver Sleeve
with side feed hole .................. 315140
SILVER-SAVER SPLASH
GUARD RING
Nitrile Rubber Silver-Saver and Splash
Guard Rink (for 7" opening cones,
sinks and adapter) ................... 315124
SINK ADAPTER — Standard
Group D Accessory
7" I.D. Stainless Steel Adapter for
Welding to Sink or Trough ....... 292123
VACUUM BREAKERS — Luster
Chrome Plated
3
4" ............................................... 315138
Water Swirl Vacuum Breaker
GROUP C
Nitrile Rubber Silver-Saver Splash Guard Ring
16" x 20" x 7" Stainless Steel Sink with Adapter and Water Inlet
Vacuum Breaker
Pre-Rinse Spray with Wall Bracket
Sink 16" x 20" x 7" (7" opening)
w/hole for water inlet ...........ML-32662
WATER INLETS
1
2" N.P.T.
3
4" N.P.T.
Cone Water Swirl Inlet
................................................ 315122
Fixed Direction Water Inlet (for sinks or
troughs)
FLOW CONTROL
10 Gallons per minute for
Model FD-500 —
................................................ 315150
CONE COVER – STAINLESS STEEL
15" Cone cover w/feed hole ...ML-33268 18" Cone Cover w/feed hole ...ML-33269
1
2" N.P.T. ................... 315142
PRE-RINSE SPRAYS
PR-3 Heavy-duty Flexible Pre-rinse Spray (40" high with wall bracket) ML-32333
PR-4 Utility Spray (with wall bracket) ML-32334
Adapters are available to install Hobart Disposers on existing cones. See Form F-7543
Page 2 of 4 F-8391 – FD500 Foodwaste Disposers
Loading...
+ 2 hidden pages