Item # _____________________________________
Quantity ___________________________________
C.S.I. Section 114000
FD3/50 FD3/75 FD3/125
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
COMPACT SIZE BIG VERSATILITY
Hobart Disposers are well recognized for quality
and capacity. They’re designed with your needs in
mind - built with a large capacity for food wastes.
The following pages illustrate the variations of
controls and accessories available to make these
food waste disposers the most versatile equipment
for small to medium sized clean-up systems.
SPECIFICATIONS
MOTORS: Continuous duty rating, equipped with
manual reset thermal overload inherent protector.
Per manently lubricated ball bear ings for upper
and lower shelf support. Upper bearing is sealed on
both sides.
HOUSINGS: Heavy aluminum grind and discharge
housings. Four bolts fasten the motor unit to the
grind chamber, permit easy removal.
FOODWASTE DISPOSERS
MOTOR SHAFT SEAL: Face-type seal consists
of sintered bronze mating ring and spring loaded
carbon ring insert in chemical resistant neoprene
bellows. Mating surfaces are protected from grit or
bers by being recessed into ywheel. Should any
moisture pass this seal, a inger and drain tube are
provided to insure immediate removal. In
addition, a lip-type oil seal (located beneath the
bearings) is an “added protection” water seal.
DRAIN CONNECTOR: A chrome plated brass tailpiece is provided for connection to a 11⁄2" standard
drain trap.
DUAL DIRECTIONAL GRINDING: All Disposers
operate in either di rection of ywheel rotation.
Direc tion of rotation can be controlled by the
operator (to increase life and efciency of grinding
elements — back ywheel free of a “jam”) when
installed with Control Groups 5 & 6.
WEIGHT: Shipping – Approx. 60 lbs. (does not
include accessory group or controls).
FD3/50 FD3/75 FD3/125 FOODWASTE DISPOSERS
MOUNTING: All Hobart Disposers (except when
using accessory group E), fasten to 7" I.D. (throat
opening) cones. A vinyl isolating ring eliminates
metal-to-metal contact at the cone mounting,
reduces vibration and noise transmission.
STATIONARY SHREDDER RING: 13⁄4" high,
4 machine ground primary action breaker bars,
42 secondary action grinding teeth.
FLYWHEEL: Breaker blade, mounted at center,
speeds grinding, prevents objects from “riding” at
center. Two hardened stainless steel cutter blocks
(fastened to ywheel with nylock screws) are
replaceable, can be indexed for new cutting edges.
Ni-Resist ywheel is 63⁄16" diameter, slots undercut
the shredder ring to assure that particles are cut to
proper size before passing to the drain line.
Complies with
ASSE 1009
Long Housing Model
F8567 – FD3/50 FD3/75 FD3/125 Foodwaste Disposers Page 1 of 4
FD3/50 FD3/75 FD3/125
FOODWASTE DISPOSERS
ACCESSORY GROUPS
GROUP A (For use with long upper
housing only.)
Vinyl Scrapping
Ring
Stainless Steel
Silver-Saver Sleeve
with Side Feed
Hole
Water Swirl Vacuum Breaker
GROUP B (For use with long upper
housing only.)
Vinyl Silver-Saver
Splash Guard Ring
GROUP E (For use with short upper
housing only.)
NOTE: For use with short
Upper Housing Foodwaste
Disposer only.
Cover Stopper and Sink
Adapter Assembly for
31⁄2" to 4" Sink Opening
Fixed Direction Vacuum Breaker
Water Inlet for Sink
ACCESSORY
COMPONENTS
CONES-SINK—Stainless Steel
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
FLOW CONTROL
Part No.
5 Gallons per minute for
Model FD3/50 through
FD3/125 — 3⁄4" N.P.T. .............. 201721
CONE COVER –
STAINLESS STEEL
15" Cone cover w/feed hole ....... 204024
18" Cone Cover w/feed hole ....... 204023
CONE FEEDING ACCESSORIES
Vinyl Scrapping Ring ................... 202113
Water Swirl Vacuum Breaker
GROUP C (For use with long upper
housing only.)
Vinyl Silver-Saver
Splash Guard Ring
Vacuum Breaker
Part No.
Cone 15" I.D. w/hole for
water swirl inlet ....................... 204007
Cone 18" I.D. w/hole for
water swirl inlet ....................... 204004
Cone 15" I.D. w/out swirl hole .... 204006
Cone 18" I.D. w/out swirl hole .... 204003
Sink 16" x 20" x 7" (7" opening)
w/hole for water inlet ............204015-2
WATER INLETS
Cone Water Swirl Inlet
1
⁄2" N.P.T. ................................. 204380
Stainless Steel Silver-Saver
Sleeve with side feed hole....... 203870
SILVER-SAVER SPLASH
GUARD RING
Vinyl Silver-Saver and Splash
Guard Ring (for 7" opening
cones, sinks and adapter) ....... 202120
VACUUM BREAKERS —
Chrome Plated
3
⁄4" ............................................... 277112
PRE-RINSE SPRAYS
PR-3 Heavy-duty
Flexible Pre-Rinse
Spray (38" high
with wall bracket)
ML-32333
Pre-Rinse Spray
with Wall Bracket
Fixed Direction Water Inlet
(for sinks or troughs)
1
⁄2" N.P.T. ................................. 204346
Adapters are available to install Hobart Disposers
on existing cones. See Form F7543.
Page 2 of 4 F8567 – FD3/50 FD3/75 FD3/125 Foodwaste Disposers
Loading...