MODEL 6430T, 6460 & 6460T
POTATO PEELER
MODEL
ML-137602 6430T
ML-19630 6460
ML-137604 6460T
ML-104562 6460C
ML-137606 6460CT
701 S. RIDGE AVENUE
TROY, OHIO 45374-0001
FORM 37005 (Apr. 2006)
Installation, Operation and Care of
MODEL 6430, 6430T, 6460 & 6460T PEELERS
SAVE THESE INSTRUCTIONS
GENERAL
Models 6430 and 6430T Peelers are designed to peel 30 to 33 lbs (13.5 to 15.0 kg) of product in 1 to
3 minutes using a
and is available for single-phase electrical service ONLY.
Models 6460 and 6460T Peelers are designed to peel 50 to 60 lbs (22.5 to 27.0 kg) of product in 1 to
3 minutes using a 1 HP, single- or three-phase electric motor. The 6460T includes a synchronous timer
and is available for single-phase electrical service ONLY.
All models incorporate a reinforced peeling disc with the abrasive permanently bonded to its surface
and a Lexan Liner for the inside of the hopper. The switch or timer is mounted on the right side of the
discharge chute as standard but can be ordered on the left or changed in the field. The bottom of the
peeler unit is cushioned with a rubber trim molding which also provides a seal.
Optional accessories include a peel trap or disposer stand.
3
/4 HP, single- or three-phase electric motor. The 6430T includes a synchronous timer
INSTALLATION
NOTE: Immediately after unpacking, machine should be checked for possible shipping damage. If the
machine is found to be damaged after unpacking, save the packaging material and contact the shipper.
This machine MUST be cleaned after installation and before being put into service. Refer to
MAINTENANCE for instructions.
PEELER UNIT (FIG. 1)
1. Remove the peeler from its shipping carton and remove the hopper top.
2. Remove the fill tube and bracket assembly from the peeler housing and the cloth bag containing
the fill tube gasket and acorn nuts.
3. Do NOT remove the rubber molding on bottom of peeler.
4. Lay the peeler on its side. Slightly loosen the clamp that attaches the drain hose and pull the drain
hose down so that it extends approximately
clamp.
On units that will NOT use a peel trap or disposer stand, attach the bottom cover plate using the bolts
and washers supplied with the unit.
7
/8" below the bottom of peeler housing. Tighten the
– 2 –
DATA PLATE
HOPPER TOP
BRACKET ASSEMBLY
SCREW
TUBE COUPLING
ABRASIVE DISC
LOCK WASHER
AND WASHER
PEEL TRAP
DRAWER
SWITCH
PEELER
HARDWARE
JUNCTION
BOX
DISPOSER
SWITCH
JUNCTION BOX COVER
CONDUIT HOLE
INLET TUBING
RUBBER MOLDING
DISPOSER
FLANGE
ADAPTER
PLATE
DISPOSER
PL-56337
PEEL TRAP DISPOSER STAND
Fig. 1
– 3 –
LEXAN LINER
1. Slide the liner (Fig. 2) into the hopper, ensure the liner is under retaining brackets (Fig. 2) and
resting on the top of the lip (Fig. 2) on the bottom of the hopper chamber.
LINER
RETAINING
BRACKETS
LIP
KEEPER
PL-41652-1
Fig. 2 Fig. 3
PL-41653
2. Push the liner keeper into the hole (Fig. 3) provided.
3. Secure the keeper using the exterior latch.
PEEL TRAP
If a peel trap is to be used, unpack the trap from its shipping carton. Remove the legs and cloth bag from
inside the peel trap. The cloth bag contains hardware for attaching the legs.
Legs
It will be necessary to remove the peel trap drawer (Fig. 1) to allow enough room for attaching the legs.
– 4 –
Assemble the legs as follows (Fig. 4):
1. Lay the peel trap on its side.
2. Assemble one of the rubber gaskets to one of the curved leg clamp bolts.
3. Assemble the bolt and gasket from the inside, through one of the leg bolt holes in the peeler
housing.
4. Assemble a leg and a leg slot cover on the leg clamp bolt.
5. Place a stainless steel washer and acorn nut onto the clamp bolt and partially tightened, set unit
upright.
6. Each leg has an upper and lower leg clamp bolt assembly. When all are assembled and partially
tightened, set unit upright.
7. Adjust each leg to a suitable height such that the unit is level, and tighten the acorn nuts.
ACORN NUT
WASHER
SLOT COVER
Fig. 4
CLAMP BOLT
RUBBER GASKET
LEG
PL-41651-1
Peelers
The peeler may be positioned on the peel trap in one of four positions. Each of the positions will cause
the peel trap drawer to be located in a different position relative to the discharge chute.
The peel trap drawer may be directly beneath the discharge chute, to the right, left or rear (see Fig. 5).
After selecting the most convenient position for the peel trap drawer, remove the cover disc from the
appropriate hole in the peel trap top and position the peeler on top of the peel trap, with the peeler drain
hose extending through selected hole (Fig. 5).
The cloth bag shipped in peel trap drawer contains the capscrews, lockwashers and washers (Fig. 1)
necessary for fastening the peeler to peel trap.
CAUTION: Excessive tightening of screws may distort housing.
If desired, the peel trap legs may be bolted to the floor.
– 5 –
RELATIONSHIP OF PEELER WITH TRAP VIEW OF TOP OF PEEL TRAP
Discharge
Chute
To position peel trap
drawer BENEATH the
discharge chute:
To position peel trap
drawer to the RIGHT
of discharge chute:
To position peel trap
drawer to the LEFT
of discharge chute:
Peel Trap
Drawer
Discharge
Chute
Peel Trap
Drawer
Discharge
Chute
Peel Trap
Drawer
Remove cover disc and
place drain hose through
this hole.
Remove cover disc and
place drain hose through
this hole.
Remove cover disc and
place drain hose through
this hole.
To position peel trap
drawer to the REAR
of discharge chute:
Discharge
Chute
Peel Trap
Drawer
(in Rear)
Fig. 5
– 6 –
Remove cover disc and
place drain hose through
this hole.
PL-56327
DISPOSER STAND
If a disposer stand is to be used, unpack the stand from its shipping carton. The feet may be threaded
in or out as necessary to level the disposer stand.
The disposer flange, adapter plate, gaskets and all hardware required for mounting the disposer are
assembled and packed in a separate container. Refer to the disposer manual shipped with the disposer
and follow the recommendations contained in it. Remove the three mounting bolts and lockwashers
from the disposer flange.
Attach the disposer flange (Fig. 1) and if necessary, the adapter plate (Fig. 1) to the disposer.
NOTE: If a Hobart disposer is used, remove and discard the adapter plate and the smaller of the two
gaskets.
Using the three mounting bolts and lockwashers (previously removed from disposer flange), mount the
disposer and flange assembly to the disposer stand.
Peeler
Position the peeler on top of the disposer stand. Place the peeler drain hose in the hole above the
disposer. Fasten the peeler to the stand using hardware (Fig. 1) shipped in the bag tied to the disposer
stand.
If desired, the disposer stand feet may be bolted to the floor.
PLUMBING
WARNING: PLUMBING CONNECTIONS MUST COMPLY WITH APPLICABLE SANITARY, SAFETY
AND PLUMBING CODES.
Peeler Unit Without Disposer
Using the supplied acorn nuts and gasket, attach the fill tube and bracket assembly (Fig. 1) to the peeler.
Connect a cold water supply to the
1
/2" fill tube coupling (Fig. 1).
NOTE: A globe valve for controlling water supply should be installed in the water supply line at a
location convenient to the operator.
Peeler Unit With Disposer
Using the supplied acorn nuts and gasket, attach the fill tube and bracket assembly (Fig. 1) to the peeler.
Connect the water inlet tubing (Fig. 1) to the
1
/2" fill tube coupling (Fig. 1). Connect the other end of the
water inlet tubing to the fill valve, which is mounted on the disposer stand.
Connect a cold water supply line to the fill valve, which has a
3
/8"-18 N.P.S. female connection.
– 7 –
ELECTRICAL CONNECTIONS
Before making electrical connections, check the specifications on peeler data plate (Fig 1), as well as
those of the disposer (where applicable), to assure they agree with those of your electrical service.
WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE
APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL
ELECTRICAL CODES.
WARNING: DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOW
LOCKOUT / TAGOUT PROCEDURES.
If it is desired to move the switch (Fig. 1) or timer to the opposite side of the discharge chute, simply
remove the screws that attach the switch or timer and cover plates. Interchange the switch or timer and
cover plates and fasten each with the screws.
7
/8" conduit hole (Fig. 1) is provided in the peeler housing for 1/2" trade size electrical conduit. Remove
A
the junction box cover (Fig. 1), make electrical connections and replace the cover.
A separate junction box (Fig. 1) is provided for making disposer connections.
NOTE: The following information is compiled in accordance with the National Electrical Code, latest
edition.
BRANCH CIRCUIT SIZE AND PROTECTION
ESUFYALED-EMITTNEMELELAUD
tiucriCmuminiM
stloVesahP
034606460346064
51115252525201
032-00215151515141
032-0023515160141
064351513641
stloVesahP
0346064603460646
51115203520301
032-00210202020221
yticapmA
REKAERBTIUCRICEMITESREVNI
tiucriCmuminiM
yticapmA
eziSesuFmumixaM
6
tiucriCmumixaM
eziSrekaerB
C°06
reppoC
eziSeriW
C°06
reppoC
eziSeriW
032-00235151010141
064351516641
– 8 –
OPERATION
Using the lugs on the hopper top as locators, position the hopper top on the housing and turn it
clockwise into place.
Close and latch the discharge chute door.
Pour the product into the hopper. There should be room in the hopper for the product to move around
while peeling. Do NOT overload the peeler; peeler capacities are 30 to 33 lbs (13.5 to 15.0 kg)
maximum for the 6430/6430T and 50 to 60 lbs (22.5 to 27.0 kg) for the 6460/6460T.
Turn on the water supply. On units with a disposer , turn on the disposer switch (Fig. 1). This will open
the valve.
Turn on the peeler. On units equipped with a timer, set the timer at the desired time.
Peeling times will vary depending on the type and condition of product. When the desired degree of
peeling has been reached, turn off the water (or disposer where applicable). Place a container to catch
the product under the discharge chute door.
NOTE: On units equipped with a timer, if the timer has expired, it will be necessary to reset the timer
to allow enough time for the product to be discharged.
After the product has been completely discharged, turn off the peeler and it is ready for a repeat
operation.
If the peeler is equipped with a peel trap, it will be necessary to empty the peel trap drawer occasionally
(after a few batches).
WARNING: DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOW
LOCKOUT / TAGOUT PROCEDURES.
CLEANING
The peeler should be cleaned after the peeling operation has been completed.
As soon as the peeling operation has been completed and BEFORE the hopper has had time to dry,
turn on the water or disposer, if equipped, and flush the interior of the hopper. Turn off the water (or
disposer).
Rotate the hopper top COUNTERCLOCKWISE and lift to remove. Clean the hopper top in a sink.
Lift out the abrasive disc (Fig. 1), which is NOT fastened to the shaft and scrub it with a brush and mild
soap. Clean the housing beneath the abrasive disc with mild soap and water.
NOTE: If the abrasive disc should stick and is NOT easily removed, it may be loosened by removing
5
the hex head screw (Fig. 1) on top of the hub and threading a longer screw (such as
1
1-
/2") in until disc loosens.
/16"-18 x
To remove the lexan liner, unlatch the exterior latch on the outside of the hopper and push the keeper
out of the hole (Fig. 3). Slide the liner out from under the retaining brackets. Take to the sink and scrub
with a nonabrasive brush, using soap and water to clean. Allow to air dry before installing into the
hopper.
– 9 –
Turn on the water or disposer, if equipped, and thoroughly clean the interior of the hopper using a mild
soap and brush. Turn off the water or disposer.
If the drawer is equipped with a peel trap, remove the peel trap drawer and thoroughly clean the drawer,
as well as the peel trap interior.
The discharge chute MUST be left open when the unit is NOT in use in order to prolong the life of the
door seal.
MOTOR
This machine is equipped with a manual-reset overload protection switch. If during operation, the motor
should overheat and trip this switch, turn the peeler switch or timer off and allow the motor to cool for
several minutes. To reset the switch, remove the top screw from the round cover plate (Fig. 6), rotate
the cover plate and push the red button (Fig. 6). Install round cover plate and screw onto potato peeler.
If the overload switch persists in tripping, contact your local Hobart Service Office.
LUBRICATION
RED BUTTON
COVER PLATE
PL-41650-1
Fig. 6
MAINTENANCE
The peeler uses sealed ball bearings and therefore, requires no lubrication maintenance.
– 10 –
TROUBLESHOOTING
SYMPTOM POSSIBLE CAUSE
Peeler won't operate. Electrical power not connected.
Circuit breaker tripped or fuse blown.
Excessive foaming. Too much water in the hopper.
If the above suggestions do not remedy the situation, contact Hobart Service Office.
SERVICE
Contact your local Hobart-authorized Service Office for any repairs or adjustments needed on this
equipment.
– 11 –
PL-56334
INSTALLATION DIAGRAM (WITHOUT TRAP)
– 12 –
PL-56333
INSTALLATION DIAGRAM (WITH TRAP)
– 13 –
PL-56335
INSTALLATION DIAGRAM (DISPOSER STAND)
– 14 –
NOTES
– 15 –
NOTES
FORM 37005 (Apr. 2006) PRINTED IN THE U.S.A.
– 16 –
Loading...