HIKVISION DS-K1101M, DS-K1101C, DS-K1101MK, DS-K1102MK, DS-K1102M Installation Manual

DS-K1100 Series Card Reader

Installation Manual

UD.6L0206A1003A01

1

Thank you for purchasing our product. If there is any question or
request, please do not hesitate to contact the dealer.
This manual is applicable to the following models:

Series

Models

Description

DS-K1101
Series

DS-K1101M

MIFARE card reader (without keypad)

DS-K1101MK

MIFARE card reader (with a keypad)

DS-K1101C

CPU card reader (without keypad)

DS-K1101CK

CPU card reader (with a keypad)

DS-K1102
Series

DS-K1102M

MIFARE card reader (without keypad)

DS-K1102MK

MIFARE card reader (with a keypad)

DS-K1102C

CPU card reader (without keypad)

DS-K1102CK

CPU card reader (with a keypad)

DS-K1103
Series

DS-K1103M

MIFARE card reader (without keypad)

DS-K1103MK

MIFARE card reader (with a keypad)

DS-K1103C

CPU card reader (without keypad)

DS-K1103CK

CPU card reader (with a keypad)

This manual is a kind of guide only for reference and may contain
several technically inaccurate points or printing errors, and the
content is subject to change without notice. The updates will be
added into the new version of this manual. We will readily
improve or update the products or procedures described in the
manual.
There may be differences between real object. The real product
should be considered as final.

2

Chapter 1 Preventive and Cautionary

Tips

To guarantee the card reader works properly, please read and
obey the notes below.

 If the card reader is powered by the controller, the power

supply distance is recommended to be no longer than 100m.
If the distance is longer than 100m, you are advised to power
the card reader by external 12V (range: -%10 ~ +%10) DC
power supply, which is nonswitched and linear.

 To guarantee the communication between the controller and

the card reader, you must use RVVP cable above 0.5 to
connect them.

 If the card reader is installed outside or in environment easy

to permeable, it is advisable to install a waterproof shield.

 If you need to install several card readers, the distance

among them must over 30cm.

 To reduce the noise in long distance transmission, the shield

of cable should connect to the GND of both controller and
card reader terminal.

Chapter 2 Introduction

DS-K1100 series card reader is a kind of high-performance
product, with a 32 bit high-speed processor. It communicates with
access controller via either RS-485 protocol or Wiegand protocol.
And a build-in tamper-proof module helps to protect card reader
from malicious damage. As to the physical appearance, the
PC+ABS material makes water proof and dust proof possible in
poor environment.

3

2.1 Front View

The front view of DS-K1101 series card reader is shown below:

Figure 2-1 DS-K1101MK/DS-K1101CK

Figure 2-2 DS-K1101M/DS-K1101C

The front view of DS-K1102 series card reader is shown below:

Figure 2-3 DS-K1102MK/DS-K1102CK

Figure 2-4 DS-K1102M/DS-K1102C

The front view of DS-K1103 series card reader is shown below:

4

Figure 2-5 DS-K1103MK/DS-K1103CK

Figure 2-6 DS-K1103M/DS-K1103C

2.2 Rear View

The rear view of card reader is shown below:

1

2

3

4

5

Figure 2-7 Rear View of DS-K1101 Series