Henny Penny OFG-390 User Manual

HENNY PENNY

6 HEAD GAS OPEN FR YER

SPECIFICA TIONS

Height 61" (155 cm)

Width 24" (61 cm)

Depth 41¾" ( 107 cm)

Floor Space Approximately 7 sq. ft. (.65 sq. m.)

Pot Capacity 6 Head of chicken - 20 lbs. (9 kg.)

130 lbs. shortening (46 Kg.)

Model OFG- 390

Electrical 120 VAC, 1 Phase, 50/60 Hz, 10 Amp, 2 Wire + Ground

230 VAC, 1 Phase, 50/60 Hz, 5 Amp, 2 Wire + Ground

Heating Propane or Natural Gas; 100,000 BTU/Hr.(29.3 kw)

Shipping W eight Approximately 670 lbs. (304 kg.)

A data plate, located on the back shroud behind the lid, gives the information of the type of
fryer, serial number , warranty date, and other information pertaining to fryer . Also, the serial
number is stamped on the outside of the frypot. See figure below .

1003

Model OFG- 390

TABLE OF CONTENTS

Section Page

Section 1. TROUBLESHOOTING.............................................................................................1-1

1-1 Introduction ....................................................................................................1-1

1-2 Safety .............................................................................................................1-1

1-3 Troubleshooting .............................................................................................. 1-2

1-4 Error Codes ....................................................................................................1-10

Section 2. MAINTENANCE.......................................................................................................2-1

2-1 Introduction ....................................................................................................2-1

2-2 Maintenance Hints ......................................................................................... 2- 1

2-3 Preventive Maintenance ................................................................................ 2-1

2-4 High Limit T emperature Control .................................................................... 2- 2

2-5 Power/Pump Switch ...................................................................................... 2-4

2-6 Temperature Probe Replacement ..................................................................2-5

2-7 Complete Control Panel - Henny Penny ........................................................2-6

2-8 Lid Couterweight Cables................................................................................ 2- 7

2-9 Gas Control Valve .......................................................................................... 2 -9

2-10 Blower Assembly ........................................................................................... 2 -11

2-11 Transformer....................................................................................................2-12

2-12 Airflow Switch ............................................................................................... 2-13

2-13 Drain Microswitch ......................................................................................... 2-14

2-14 Drain Valve and Extension .............................................................................2-15

2-15 Air V alve ........................................................................................................2-16

2-16 Cleaning the Dilution Box............................................................................... 2-17

2-17 Cleaning the Blower Wheel ...........................................................................2-17

2-18 Ignition Modules ............................................................................................. 2-18

2-19 Ignitor Assembly ............................................................................................ 2-19

2-20 Flame Sensor Assembly .................................................................................2-20

2-21 Ignitor and Flame Sensor Adjustment ............................................................ 2-20

2-22 Nylatron Strips Replacement .........................................................................2-21

2-23 Lubricating Lid Rollers ...................................................................................2-22

2-24 Relays.............................................................................................................2-22

120 V olt W iring Diagram ................................................................................2-23

208-240 V olt Wiring Diagram......................................................................... 2-24

230 V olt W iring Diagram ................................................................................2-25

120 V olt F AST W iring Diagram .....................................................................2-26

208-240 V olt F AST W iring Diagram .............................................................. 2-27

230 V olt F AST W iring Diagram .....................................................................2-28

Section 3. P AR TS INFORMATION ........................................................................................... 3-1

3-1 Introduction ....................................................................................................3-1

3-2 Genuine Parts .................................................................................................3-1

3-3 How To Order................................................................................................ 3-1

3-4 Prices .............................................................................................................3-1

3-5 Delivery ..........................................................................................................3-1

3-6 Warranty ........................................................................................................3-1

3-7 Recommended Spare Parts for Distributors .................................................. 3-1

1209 i