Sneeze Guards
Pare-haleine
SGPT, SGCP, and SGEN Series/Série Installation and Operating Manual Manuel d'installation et d'utilisation
P/N 07.04.718.00
WARNING
Do not operate this equipment unless you have read and understood the contents of this manual! Failure to follow the instructions contained in this manual may result in serious injury or death. This manual contains important safety information concerning the maintenance, use, and operation of this product. If you’re unable to understand the contents of this manual, please bring it to the attention of your supervisor. Keep this manual in a safe location for future reference.
ADVERTENCIA
No opere este equipo al menos que haya leído y comprendido el contenido de este manual! Cualquier falla en el seguimiento de las instrucciones contenidas en este manual puede resultar en un serio lesión o muerte. Este manual contiene importante información sobre seguridad concerniente al mantenimiento, uso y operación de este producto. Si usted no puede entender el contenido de este manual por favor pregunte a su supervisor. Almacenar este manual en una localización segura para la referencia futura.
AVERTISSEMENT
Ne pas utiliser cet équipement sans avoir lu et compris le contenu de ce manuel ! Le non-respect des instructions contenues dans ce manuel peut entraîner de graves blessures ou la mort. Ce manuel contient des informations importantes concernant l'entretien, l'utilisation et le fonctionnement de ce produit. Si vous ne comprenez pas le contenu de ce manuel, veuillez le signaler à votre supérieur. Conservez ce manuel dans un endroit sûr pour pouvoir vous y référer plus tard.
Français = p 12
© 2015 Hatco Corporation
CONTENTS |
|
English |
Important Owner Information .............................................. |
2 |
Introduction........................................................................... |
2 |
Important Safety Information............................................... |
3 |
Model Designation................................................................ |
3 |
Model Description................................................................. |
4 |
Specifications........................................................................ |
5 |
Dimensions .......................................................................... |
5 |
Installation ............................................................................. |
6 |
General ................................................................................ |
6 |
SGPT model Installation ...................................................... |
6 |
SGCP model Installation...................................................... |
7 |
SGEN model Installation...................................................... |
8 |
Maintenance .......................................................................... |
9 |
General ................................................................................ |
9 |
Daily Cleaning...................................................................... |
9 |
Limited Warranty................................................................. |
10 |
Addendum ........................................................................... |
11 |
Authorized Parts Distributors ............................ |
Back Cover |
IMPORTANT OWNER INFORMATION
|
|
|
|
|
Record the model number, serial number, voltage, and purchase |
Business |
|
||
date of the unit in the spaces below (specification label located |
Hours: |
7:00 am to 5:00 Pm Central Standard Time (CST) |
||
on the post). Please have this information available when calling |
|
(Summer Hours: June to September— |
||
Hatco for service assistance. |
|
|||
|
7:00 am to 5:00 Pm CST monday–Thursday |
|||
|
|
|
|
|
model No. ________________________________________ |
|
7:00 am to 4:00 Pm CST Friday) |
||
Serial No. ________________________________________ |
Telephone: 800-558-0607; 414-671-6350 |
|||
Voltage __________________________________________ |
E-mail: |
partsandservice@hatcocorp.com |
||
|
|
|||
Date of Purchase __________________________________ |
Fax: |
800-690-2966 (Parts and Service) |
||
|
414-671-3976 (International) |
|||
|
|
|
|
|
|
|
|
|
|
|
Register your unit! |
|
24 Hour 7 Day Parts and Service |
|
|
Completing online warranty registration will prevent delay in |
|
|
Assistance available in the United States |
|
obtaining warranty coverage. access the Hatco website at |
|
|
and Canada by calling 800-558-0607. |
|
www.hatcocorp.com, select the Parts & Service pull-down |
|
additional information can be found by visiting our web site at |
|
|
menu, and click on “Warranty Registration”. |
|
||
|
|
|
www.hatcocorp.com. |
|
|
|
|
INTRODUCTION
Enhance and protect food products simultaneously with Hatco Sneeze Guards. Ideal for buffet lines and serving stations, the Sneeze Guards guarantee resilient functionality in a stylish design, allowing you to safeguard your food while displaying it clearly to customers.
Sneeze Guards are products of extensive research and field testing. The materials used were selected for maximum durability, attractive appearance, and optimum performance. Every unit is inspected thoroughly prior to shipment.
This manual provides installation and safety instructions for Sneeze Guards. Hatco recommends all installation and safety instructions appearing in this manual be read prior to installation of the unit.
Safety information that appears in this manual is identified by the following signal word panels:
WARNING |
|
not |
WARNING indicates a hazardous situation which, if |
||
avoided, could result in death or serious injury. |
|
|
CAUTION |
|
not |
CAUTION indicates a hazardous situation which, if |
||
avoided, could result in minor or moderate injury. |
|
|
NOTICE |
|
|
NOTICE is used to address practices not |
related |
to |
personal injury. |
|
|
2 |
Form No. SGm-0815 |
|
|
|
English |
|
IMPORTANT SAFETy INFORMATION |
|
|
|
|
|
CAUTION
Locate unit in an area that is convenient for use. Location should be level to prevent unit from falling or moving accidentally.
NOTICE
DO NOT submerge or saturate with water. Unit is not waterproof.
Do not steam clean or use excessive water on unit.
This unit is not “jet-proof” construction. Do not use jetclean spray to clean unit.
This unit has no “user-serviceable” parts. If service is required on this unit, contact an Authorized Hatco Service Agent or contact the Hatco Service Department at 800-558-0607 or 414-671-6350; fax 800-690-2966; or International fax 414-671-3976.
NOTICE
Use non-abrasive cleaners and cloths only. Abrasive cleaners and cloths could scratch finish of unit, marring its appearance and making it susceptible to soil accumulation. Clean unit daily to avoid malfunctions and maintain sanitary operation.
Do not use harsh chemicals such as bleach, cleaners containing bleach, or oven cleaners to clean unit.
NSF Requirements
SGPT and SGCP models: The vertical distance between the finished floor and the bottom leading edge of a food shield must be 52″ (1321 mm) or less.
SGPT and SGCP models: The horizontal distance between the front of countertop equipment and the bottom leading edge of a food shield shall be 7″ (178 mm) or more.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
MODEL DESIGNATION |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
S G X X - X X |
|||||||||||
Sneeze Guard |
|
|
|
|
|
|
|
|
|
|
Width (in inches) |
|
|
|
|
|
|
|
|
|
|
|
|||
PT = Portable |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CP = Countertop Post |
|
|
|
|
|
|
|
|
|
|
|
|
EN = Enclosure |
|
|
|
|
|
|
|
|
|
|
|
|
Form No. SGm-0815 |
3 |
|
|
|
|
|
|
English |
MODEL DESCRIPTION |
|
|
|
|
|
|
|
|
All Models |
SGCP Models |
|
Enhance and protect food products simultaneously with Hatco |
The SGCP model is mounted to a countertop with an adjustable |
|
Sneeze Guards. Ideal for buffet lines and serving stations, the |
height. |
|
Sneeze Guards guarantee resilient functionality in a stylish |
|
|
design, allowing you to safeguard your food while displaying it |
|
|
clearly to customers. Hatco sneeze guards meet NSF |
|
|
standards. |
|
Adjustment |
SGPT Model |
|
|
|
|
Height |
The SGPT model is a portable sneeze guard with an adjustable |
|
Knobs |
height. |
|
|
Height
Adjustment
Knobs
SGEN Models
The SGEN model is mounted to the countertop and offers protection on three sides and overhead.
model SGPT
model SGEN
4 |
Form No. SGm-0815 |
|
English
Dimensions
SPECIFICATIONS
25-1/4″–61-1/4″ (642–1556 mm)* |
SGPT Models |
|
22″ |
|
(559 mm) |
|
19-3/16″–24-5/16″ |
|
(487–618 mm) |
20-1/8″–56-1/8″* |
|
(511–1426 mm) |
|
21-5/8″–57-5/8″* |
|
(550–1464 mm) |
|
25-1/4″–61-1/4″ (642–1556 mm)* |
SGCP Models |
|
22″ |
|
(559 mm) |
|
20-3/4″–25-7/8″ |
|
(526–657 mm) |
18-9/16″–54-9/16″* |
|
(472–1386 mm) |
|
21-5/8″–57-5/8″* |
|
(550–1464 mm) |
|
22″–58″ (559–1473 mm)* |
SGEN Models |
|
19″ |
|
(482 mm) |
16-7/16″–52-7/16″* (418–1332 mm)
19-1/2″–55-1/2″* (495–1410 mm)
60°
12″–17-1/4″ (307–438 mm)
18-1/2″ (470 mm)
20-5/16″ (516 mm)
60°
13-1/2″–18-1/2″ (345–470 mm)
18″ (457 mm)
13-3/16″ (335 mm)
16-5/16″ (414 mm)
* Units are sold in increments of 6″ (152 mm) widths.
Add the following to the smallest measurement in the range to determine each model’s specific width dimensions:
SGPT-24, SGCP-24, and SGEN-22 models add 0″ (0 mm) SGPT-30, SGCP-30, and SGEN-28 models add 6″ (152 mm) SGPT-36, SGCP-36, and SGEN-34 models add 12″ (305 mm) SGPT-42, SGCP-42, and SGEN-40 models add 18″ (457 mm) SGPT-48, SGCP-48, and SGEN-46 models add 24″ (610 mm) SGPT-54, SGCP-54, and SGEN-52 models add 30″ (762 mm) SGPT-60, SGCP-60, and SGEN-58 models add 36″ (914 mm)
Form No. SGm-0815 |
5 |
|
|
|
|
|
|
|
|
|
|
|
English |
|
INSTALLATION |
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
General |
|
5. Slide the glass mounting bracket through the angle |
|||
Sneeze Guards are shipped with some components pre- |
adjustment pins. make sure both brackets are inserted into |
||||
the pins the same way to ensure both sides are angled |
|||||
assembled. Care should be taken when unpacking the shipping |
|||||
properly for a correct fit. The unit is designed for a 60° angle. |
|||||
carton to avoid damage to unit and components enclosed. |
|||||
6. Secure the glass mounting bracket into place by tightening |
|||||
NOTE: To prevent delay in obtaining warranty coverage, |
|||||
the knob into the post. |
|
|
|||
complete online warranty registration. See the |
|
|
|||
|
|
|
|||
ImPORTaNT OWNER INFORmaTION |
section for |
7. Secure the top glass sneeze guard. |
|||
details. |
|
a. Insert the mounting bolt through the glass sneeze guard. |
|||
SGPT Model Installation |
|
||||
|
b. Place a glass bushing between the glass sneeze guard |
||||
NOTE: Remove tape and protective packaging from the |
and the glass mounting bracket. |
||||
surfaces of the unit. |
|
c. Screw the mounting bolt into the glass mounting bracket. |
|||
1. Secure the base support to the bottom channel of the two |
|||||
d. Repeat on three remaining glass sneeze guard holes. |
|||||
legs using the supplied screws. |
|
8. move the sneeze guard mounts to the desired position and |
|||
• The base support can be installed on either side of leg. |
|||||
secure to the post using the knob. The bottom edge of the |
|||||
|
|
||||
• Remove the base plugs and install on opposite side, if |
top glass must be 52″ (1321 mm) or less above floor. |
||||
necessary. |
|
9. Secure the side glass to the outside of each post. |
|||
2. Secure the two posts to the base using the supplied screws. |
|||||
a. Tighten the short knob through the glass and into the |
|||||
• The posts can be installed on middle or end of leg. |
|||||
sneeze guard mount towards the top. |
|||||
• Remove the leg plugs and install on opposite side, if |
b. Place a glass bushing between side glass and post. |
||||
necessary. |
|
c. Hold the side glass clamp onto the post. |
|||
3. Slide the side glass clamp then the sneeze guard mount |
|||||
d. Tighten the long knob into the bottom hole through the |
|||||
onto each post. |
|
||||
|
glass bushing and into the clamp. |
||||
4. Slide the angle adjustment pins through the spacer and into |
|||||
e. Repeat this step on the opposite end. |
|||||
the sneeze guard mount holes. Repeat on opposite post. |
|||||
10. Place the unit in the desired location. |
|||||
|
|
||||
|
|
Mounting Bolt |
|
|
|
|
|
Angle Adjustment |
|
|
|
|
|
Pins |
|
|
|
|
Glass |
Sneeze Guard |
|
|
|
Bushing |
Mount |
|
|
||
|
|
|
Short |
||
|
|
|
Knob |
||
Knob |
|
|
|
||
Glass Mounting |
Side |
|
|
||
|
Bracket |
|
|
||
Angle Adjustment |
Glass |
|
|
||
Clamp |
|
|
|||
|
Spacer |
Glass |
|
|
|
|
Knob |
|
|
||
|
Bushing |
|
|
||
|
Post |
|
|
|
|
|
Leg Plug |
Base |
|
|
|
|
Leg |
Long |
|||
Base |
Plug |
||||
Knob |
|||||
Support |
Leg Plug |
|
|
|
|
|
Base Plug Screw |
|
|
||
|
Screw |
|
|
Post Screw
Base Support Screw
SGPT model Installation |
|
|
|
6 |
Form No. SGm-0815 |
|
|
|
|
|
|
|
English |
|
|
|
INSTALLATION |
|
|
|
|
|
|
|
|
|
|
|
|
|
SGCP Model Installation |
|
7. Place the posts in the desired location and secure the legs |
|||
NOTE: Remove tape and protective packaging from the |
into the countertop. |
|
|||
• move the mounting covers to access the mounting holes. |
|||||
surfaces of the unit. |
|
||||
1. Slide the mounting cover, side glass clamp, then the sneeze |
• Use the “mounting Template” located in the aDDENDUm |
||||
guard mounts onto each post. |
|
section at the end of this manual. |
|||
2. Slide the angle adjustment pins through the spacer and into |
8. Secure the side glass to the outside of each post. |
||||
the sneeze guard mount holes. Repeat on opposite post. |
a. Tighten the short knob into the top hole. |
||||
3. Slide the glass mounting bracket through the angle |
b. Place a glass bushing between the side glass and the |
||||
adjustment pins. make sure both sides are inserted into the |
post. |
|
|||
pins the same way to ensure both sides are angled properly |
c. Hold the side glass clamp onto the post. |
||||
for a correct fit. The unit is designed for a 60° angle. |
|||||
d. Tighten the long knob into the bottom hole through the |
|||||
4. Secure the glass mounting bracket into place by tightening |
|||||
glass bushing and into the post. |
|||||
the knob into the post. |
|
||||
|
e. Repeat this step on the opposite end. |
||||
5. Secure the top glass sneeze guard. |
|
||||
|
|
|
|||
a. Insert the mounting bolt through the glass sneeze guard. |
|
|
|||
b. Place a glass bushing between the glass sneeze guard |
|
|
|||
and the glass mounting bracket. |
|
|
|
||
c. Screw the mounting bolt into the glass mounting bracket. |
|
|
|||
d. Repeat on the three remaining glass sneeze guard |
|
|
|||
holes. |
|
|
|
||
6. move the sneeze guard mounts to the desired position and |
|
|
|||
secure to the post using the knob. The bottom edge of the |
|
|
|||
top glass must be 52″ (1321 mm) or less above floor. |
|
|
|||
|
|
|
Mounting Bolt |
|
|
|
|
|
Angle Adjustment |
|
|
|
|
|
Pins |
|
|
|
|
Glass |
Post |
|
|
|
|
Sneeze Guard |
|||
|
|
Bushing |
|||
|
|
|
Mount |
Short |
|
|
|
Knob |
|
Knob |
|
|
|
|
|
||
|
|
Glass |
|
|
|
|
|
Mounting |
|
|
|
|
|
Bracket |
|
|
|
|
Side |
Angle |
|
|
|
|
Adjustment |
|
|
||
|
Glass |
Spacer |
|
|
|
|
Clamp |
Knob |
|
|
|
|
|
|
|
||
|
|
Mounting Cove |
Long |
|
|
|
|
|
Knob |
|
Countertop Mounting
Screw
SGCP model Installation
Form No. SGm-0815 |
7 |
|
|
|
|
|
|
|
English |
|
INSTALLATION |
|
||
|
|
|
|
|
|
|
|
SGEN Model Installation |
4. Secure the top glass to the top of each post. |
||
1. Place each post in the desired location and secure the legs |
a. Insert the mounting bolt through post from underneath. |
||
into the countertop. |
b. Place a glass mount and glass bushing onto the bolt. |
||
• move the mounting covers to access the mounting |
|||
c. Slide the glass onto the bolt and secure using nut. |
|||
holes. |
|||
d. Repeat on the three remaining top glass holes. |
|||
• Use the “mounting Template” located in the aDDENDUm |
|||
|
|
||
section at the end of this manual. |
|
|
|
2. Secure the back glass to the outside of each post. |
|
|
|
a. Insert the mounting bolt through post. |
|
|
|
b. Place a glass mount then a glass bushing onto the bolt. |
|
|
|
c. Slide the glass onto the bolt and secure using nut. |
|
|
|
d. Repeat on the three remaining back glass holes. |
|
|
|
3. Secure the side glass to the outside of each post. |
|
|
|
a. Place a glass bushing between the side glass and the |
|
|
|
post. |
|
|
|
b. Hold the side glass clamp onto the post. |
|
|
|
c. Tighten the bolt into the clamp through the top hole of |
|
|
|
side glass. |
|
|
|
d. Repeat on the three remaining side glass holes. |
|
|
|
e. Repeat this step on the opposite end. |
|
|
|
|
Mounting Nut |
Glass Bushing
Glass Mount
Glass |
Glass Bushing |
Clamp |
|
|
Mounting |
|
Bolt |
Mounting
Bolt
Mounting
Cover
Countertop
Mounting
Screw
Mounting Nut
SGEN model Installation
8 |
Form No. SGm-0815 |
|