Harman Kardon AVR80II Owner's Manual

Download

Page 1

MULTI DISP OSD DELAY

Bass

Mode

Treble Balance

Volume

P•SET P•SCN TUNE

Aux

VideoS-Video

RLMaxMinMaxMin

Audio

MUTEMODE

TV LD VCR 12 AUX

TEST

•

LOGIC MOVIE HALL MATRIX MONO MULTI

MEMO

AUTO

TUNED STEREO

kHz MHz

3-LOGIC AUTO MEMO P-SCAN TAPE VCR1 DISPCOPY

Harman Kardon

AVR80

Audio/V ideoReceiver

Owner’s Manual

Page 2

Owner’s Manual

AVR80II Audio/Video Receiver

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–3

Unpacking and Installation. . . . . . . . . . . . . . . . 3

Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Front Panel Controls. . . . . . . . . . . . . . . . . . . . . . . . . . 4–5

Front Panel Information Display. . . . . . . . . . . . . . . . 6–7

Rear Panel Audio & Systems Connections. . . . . . . . . 8–9

Rear Panel Video Connections. . . . . . . . . . . . . . . . 10–11

Remote Control Functions . . . . . . . . . . . . . . . . . . . 12–13

Installation, Set Up and Configuration . . . . . . . . . 14–16

Remote Control Programming and Operation . . . 17–18

System Configuration. . . . . . . . . . . . . . . . . . . . . . . 19–22

Basic Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 23–26

Source Selection . . . . . . . . . . . . . . . . . . . . . . . . 23

Volume Control. . . . . . . . . . . . . . . . . . . . . . . . . 23

Surround Mode Selection . . . . . . . . . . . . . . . . . 23

TV Auto On Function . . . . . . . . . . . . . . . . . . . . 24

Tuner Operation. . . . . . . . . . . . . . . . . . . . . 24–26

On Screen Display. . . . . . . . . . . . . . . . . . . . . . . . . . 27–29

Advanced Functions . . . . . . . . . . . . . . . . . . . . . . . . 30–32

Audio Tape Dubbing. . . . . . . . . . . . . . . . . . . . . 30

Video Dubbing. . . . . . . . . . . . . . . . . . . . . . . . . . 30

Audio/Video Simulcast Recording . . . . . . . . . . 30

Delay Time Adjust. . . . . . . . . . . . . . . . . . . . 30–31

Direct Digital Decoding. . . . . . . . . . . . . . . . . . . 31

6 Channel Direct Operation . . . . . . . . . . . . . . . 31

Surround Mode Chart. . . . . . . . . . . . . . . . . . . . 32

Multiroom Operation . . . . . . . . . . . . . . . . . . . . . . . 33–35

System Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . 36

Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . 37

80 Crossways Park West Woodbury, NY 11797

Page 3

Introduction

Congratulations! With the purchase of a Harman Kardon AVR80II you are about to begin many years of listening enjoyment. The AVR80II has been custom designed to provide all the excitement and detail of movie soundtracks and every subtle nuance of musical selections. In addition, the AVR80II has the flexibility to expand to serve as the heart of a multiroom audio system, and the capability for use with digital multichannel audio systems.

While complex digital systems are hard at work within the AVR80II to make all of this happen, hook-up and operation are simple. Color keyed connections, a comprehensive remote control and on screen menus make the AVR80II easy to use. To obtain the maximum enjoyment from your new receiver we urge you to take a few minutes to read through this manual. This will ensure that connections to speakers, source playback units and other external devices are made properly. In addition, a few minutes spent learning the functions of the various controls will enable you to take advantage of all the power the AVR80II is able to deliver.

If you have any questions about this product, its installation or operation, please contact your retailer or custom installer. They are your best local source of information.

Description and Features

The AVR80II is a full featured A/V receiv-

er, incorporating a wide variety of listen-

ing options. In addition to standard

Dolby®Pro Logic™processing, the

AVR80II uses Twin Digital Signal

Processors to provide Home THX

Cinema and five other surround modes.

Expansion capability enables upgrades to

5.1 digital audio systems such as AC-3

™

through the use of an optional external

adapter.

A total of five audio/video inputs, each

with both composite and “S” video, as

well as three additional audio only

inputs are selected through a learning

remote control and an easy to read front

panel display or on screen graphics

through a TV monitor. Dubbing and tape

outputs are available, and multiroom

operation is available with independent

source and volume selection.

The AVR80II’s powerful amplifier uses

traditional Harman Kardon High Current

design philosophies to meet the wide

dynamic range of any program selection.

For the audio purist, the AVR80II may be

connected directly to the digital output of

an LD player, avoiding excessive D/A con-

version steps.

Harman Kardon invented the high fidelity receiver over forty years ago. With state of the art circuitry and time honored circuit designs, the AVR80

II is

undoubtedly the finest receiver ever offered by Harman Kardon.

■ Twin DSP processors for precise

surround decoding

■ Dolby ProLogic, Home THX Cinema,

Dolby 3 Stereo and three other surround modes

■ On screen menu displays

■ Learning remote control

■ Composite and “S” video switching

■ Complete Multiroom control

■ Direct Digital Input from LD

■ Preamp output/Amplifier input of

ALL channels permits ease of expansion

■ Six Channel Direct inputs for use

with external discrete digital audio adapters

Page 4

Safety Information

Important Safety Information

Verify Line Voltage Before Use

YourAVR80IIhas beendesigned for use with 120volt ACcurrent. Connection toa line voltageother thanthat for whichit is intendedcan createa safety andfire hazard, andmay damagethe unit.

If you have any questions about the voltage requirements for your specific model, or about the line voltage in your area, contact your selling dealer before plugging the unit into a wall outlet.

Do Not Use Extension Cords

To avoid safety hazards, use only the power cord attached to your unit. We do not recommend that extension cords be used with this product. As with all electrical devices, do not run power cords under rugs or carpets or place heavy objects on them. Damaged power cords should be replaced immediately with cords meeting factory specifications.

Handle the AC Power Cord Gently

When disconnecting the power cord from an AC outlet, always pull the plug, never pull the cord. If you do not intend to use the unit for any considerable length of time, disconnect the plug from the AC outlet.

Do Not Open The Cabinet

There are no user serviceable components inside this product. Opening the cabinet may present a shock hazard, and any modification to the product will void your guarantee. If water or any metal object such as a paper clip, wire or a staple accidentally falls inside the unit, disconnect it from the AC power source immediately, and consult an authorized service station.

CATV or Antenna Grounding

If an outside antenna or cable system is

connected to this product, be certain that

it is grounded so as to provide some pro-

tection against voltage surges and static

charges. Section 810 of the National

Electrical Code, ANSI/NFPA No. 70-1984,

provides information with respect to

proper grounding of the mast and sup-

porting structure, grounding of the lead-

in wire to an antenna discharge unit,

size of grounding conductors, location of

antenna discharge unit, connection to

grounding electrodes and requirements

of the grounding electrode.

NOTE TO CATV SYSTEM INSTALLER:

This reminderis providedtocall the

CATV(Cable TV)system installer’satten-

tion toarticle 820-40ofthe NECthat

provides guidelinesfor propergrounding

and, inparticular,specifies that thecable

ground shallbe connectedtothe ground-

ing systemof thebuilding,as closeto the

point ofcable entryaspossible.

Installation Location

■ To assure proper operation, and to

avoid the potential for safety hazards, place the unit on a firm and level surface. When placing the unit on a shelf, be certain that the shelf and any mounting hardware can support the weight of the product.

■ Make certain that proper space is pro-

vided both above and below the unit for ventilation. If this product will be installed in a cabinet or other enclosed area, make certain that there is sufficient air movement within the cabinet. Under some circumstances a fan may be required.

■ Do not place the unit directly on a car-

peted surface.

■ Avoid installation in extremely hot or

cold locations, or an area that is exposed to direct sunlight or heating equipment.

■ Avoid moist or humid locations.

■ Do not obstruct the ventilation slots on

the top of the unit, or place objects directly over them.

CAUTION

RISK OF ELECTRICAL SHOCK

DO NOT OPEN

CAUTION:

presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to consittute a risk of electric shock to persons.

ATTENTION:

LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equalateral triangle, is intended to alert the user to the

WARNING:

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

POUR EVITER LES CHOCS ELECTRIQUES, INRODUIRE LA

LA PRISE ET POUSSER JUSQU'AU FOND.

The exclamation point within an equalateral triangle is intended

to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Page 5

Safety Information

Cleaning

When the unit gets dirty, wipe it with a clean, soft dry cloth. If necessary, wipe it with a soft cloth dampened with mild soapy water, then a fresh cloth with clean water. Wipe dry immediately with a dry cloth. NEVER use benzene, aerosol cleaners, thinner, alcohol or any other volatile cleaning agent. Do not use abrasive cleaners, as they may damage the finish of metal parts. Avoid spraying insecticide near the unit.

Moving The Unit

Before moving the unit, be certain to disconnect any interconnection cords with other components, and make certain that you disconnect the unit from the AC outlet.

Important information for the user

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. The limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that harmful interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

■ Reorient or relocate the receiving

antenna.

■ Increase the separation between the

equipment and receiver.

■ Connect the equipment into an outlet

on a circuit different from that to which the receiver is connected.

■ Consult the dealer or an experienced

radio/TV technician for help.

Thisdevicecomplies withPart 15of the FCCRules.Operation issubject tothe followingtwoconditions: (1)this device maynotcause harmfulinterference, and (2)thisdevice mustaccept interference received,includinginterference thatmay causeundesiredoperation.

NOTE: Changes or modifications may cause this unit to fail to comply with Part 15 of the FCC Rules and may void the user’s authority to operate the equipment.

Unpacking and Installation

The carton and shipping materials used to protect your new receiver during shipment were specially designed to cushion it from shock and vibration. We suggest that you save the carton and packing materials for use in shipping if you move or should the unit ever need repair.

To minimize the size of the carton in storage, you may wish to flatten it. This is done by carefully slitting the tape seams on the bottom and collapsing the carton down to a more two dimensional appearance. Other cardboard inserts may be stored in the same manner. Packing materials that cannot be collapsed should be saved along with the carton in a plastic bag.

If you do not wish to save the packaging materials, please note that the carton and other sections of the shipping protection are recyclable. Please respect the environment and discard those materials at a local recycling center.

Conventions

In order to help you use this manual with the remote control, front panel controls, rear panel connections and on-screen menus, certain conventions have been used.

EXAMPLE – (bold type) indicates a

specific remote control or front panel button, or rear panel connection jack

EXAMPLE – (OCR type) indicates a

message that is visible through the onscreen menu system

– (number in a square) indicates a

specific front panel control

– (number in a circle) indicates an

indicator in the main front panel display

– (number in an oval) indicates a

button or indicator on the remote

– (letter in a circle) indicates a rear

panel Audio or System connection

– (letter in a square) indicates a

specific rear panel video connection

Page 6

Front Panel Controls

AM•FM T•MONCD T•2 TV LD VCR1 VCR2 AUX MULTI DISP OSD DELAY

Bass

ModeClearPhonesPower MemoVCR1Tape-1

Record Out

6-ch direct

mode

Treble Balance

Volume

P•SET P•SCN TUNE

Aux

VideoS-Video

RLMaxMinMaxMin

Audio

MUTEMODE

VISUAL

SIGNAL LEVEL

TV LD VCR 12 AUX

TEST

STEREO THX CINEMA PRO•LOGIC MOVIE HALL MATRIX MONO MULTI

MEMO

AUTO

TUNED STEREO

dB kHz

MHz

3-LOGIC AUTO MEMO P-SCAN TAPE VCR1 DISPCOPY

Ó( Ô  Ò Ú Û Ù ˝ ˆ ˜ ¯

4 5 6 9 ) !@ $ % ^

#87

1 Information display 2 Remote Sensor Window 3 AM/FM Tuner Mode Selection 4 CD 5 Tape1/Monitor 6 Tape2 7 Video Sources 8 Aux 9 Multiroom Audio Select ) Display

! OSD (On Screen Display) @ Delay # Mode $ Preset Tuning % P-Scan ^ Tune & Mute * Volume Control ( Power Ó Headphone Jack

Ô 6 Channel Direct  Tape1 Copy Ò VCR1 Copy Ú Memo Û Clear Ù FM Mode ˝ Bass ˆ Treble ˜ Balance ¯ Front Panel Inputs

Page 7

Front Panel Controls

1 Fluorescent display: This dis- play delivers messages and status indications to help you operate the receiver. Refer to the separate diagram for complete explanation of the FL display.

2 Remote Sensor Window: The sensor behind this window receives infrared signals from the remote control. Aim the remote at this area and do not block or cover it unless an external remote sensor is installed.

3 AM/FM Tuner Mode Selection:

Press this button once to select the tuner. Press it again to switch between AM and FM.

4 CD: Press this button to select the CD player.

5 Tape1/Monitor: Press this button to select Tape One as the input source. A red LED above the button will illuminate to indicate that the Tape Monitor has been selected.

6 Tape2: Press this button to select Tape2.

7 Video Sources: Press any of these buttons to select a video input source.

8 Aux: Press this button to select the source connected to the front panel Aux jacks.

9 Multiroom Audio Select: Press this button to turn on the feed to the remote zone. The remote zone will stay on after the main power switch is tuned off until it is switched off by the remote room control or by pressing this button again.

) Display: Pressthis button to turn off the frontpanel FL display. The DISP indicator willilluminate to remind youthat the unit is still turned on.

! OSD (On Screen Display): Press the button briefly to display a system status report on your video screen.

@ Delay: Press this button to increase the delay to the rear (surround) channels.

# Mode: Press these buttons to scroll up ⁄ or down ¤ through the list of available surround modes.

$ P-Set: Press these buttons to manually scroll up ⁄ or down ¤ through the FM or AM stations programmed into the receiver’s preset memory.

% P-Scan: Press this button to automatically scan through the FM or AM stations preset into the receiver’s memory. Press the button again to stop the scan when the tuner is at the desired station.

^ Tune: Press these buttons to manually scan up ⁄ or down ¤ through the FM or AM bands.

& Mute: Press this button to cut the output to the speakers. Press it again to return to the previous volume level.

* Volume Control: Turn the knob clockwise to increase volume, counterclockwise to decrease the volume. Note that approximately two revolutions of the knob are required to go from no output to maximum volume.

( Power: Press this button once to turn the unit on or off. In order to use the remote control to turn the unit on the power switch must be pressed once, and then the unit must be turned off via the remote.

Ó Headphone Jack: Plug standard stereo headphones into this jack for private listening.

NOTE: When the headphones are in use the output to the speakers is muted and the surround mode is automatically switched to STEREO. When the headphones are removed from the jack, sound to the speakers is restored and the unit returns to the previous sound mode.

Ô 6 Channel Direct: Press this but- ton to select the output of an external multichannel audio adapter.

 Tape1 Copy: Press this button to select the input for the recorder con-

nected to Tape1. The first press will select the source currently being listened to. Press again to select the input in the following order: Tuner‡ CD‡Tape 2‡ Source.

Ò VCR1 Copy: Press this button to select the input to the recorder connected to VCR1. The first press selects the input currently being viewed. Press the button again to select the input in the following order:

TV‡ LD‡ VCR2‡AUX ‡Source

Ú Memo: The memo button is used to enter stations to the tuner’s preset memory in either the manual or automatic modes. It is also used clearing the memory and when changing the TV auto on-mode.

Û Clear: The clear button is used to cancel tuning, memory input or when clearing the unit’s memories.

Ù FM Mode: Press this button to select the tuning mode for FM stations.

ı Bass: This knob adjusts the tone of low frequency sounds. Turn it to the right to boost bass frequencies or to the left to cut bass frequencies.

ˆ Treble: This knob adjusts the tone of high frequency sounds. Turn to it the right to boost high frequencies or to the left to cut high frequencies.

˜ Balance: This knob adjusts the balance between the front left and right speakers.

¯ Front Panel Inputs: Audio or Video sources connected to these jacks may be selected by pressing the Aux button 8.

Page 8

Front Panel Information Display

VISUAL

SIGNAL LEVEL

TV LD VCR 12 AUX

TEST

STEREO THX CINEMA PRO•LOGIC MOVIE HALL MATRIX MONO MULTI

MEMO

AUTO

TUNED STEREO

kHz

MHz

3-LOGIC AUTO MEMO P-SCAN TAPE VCR1 DISPCOPY

`“£¢⁄

ƒ ¥

¡ “Visual” Indicators ™ Test £ Memo ¢ Auto ∞ Tuned

§ Stereo

¶ Volume Indication

• Tuner Frequency Indication ª Main Information Display ‚ Multi ⁄ Mode Status ¤ DISP

‹ Copy Indicators › P-Scan ﬁ Auto Memo ﬂ Signal Level Indication

Page 9

Front Panel Information Display

¡ “Visual” Indicator: These indica-

tors display which input source is being fed to the video monitor output.

™ Test: This indicator flashes when

the output levels are being set using the built in test signal generator.

£ Memo: This indicatorflashes

when the Memo buttonis pressed when entering presetsand other information into the tuner’s memory.

¢ Auto: This indicator signifies that

the Automatic Tuning mode is in use for FM broadcasts.

∞ Tuned: This indicator lights when

an AM or FM station is properly tuned and locked.

§ Stereo: This indicator lights

when an FM station is broadcasting in stereo.

¶ Volume indication: The last two

indicators on the information display indicate the volume level. Note that

0dB is the reference level, not an

indication that there is no output.

• Tuner Frequency Indication:

When the tuner is in use, the main Information Display will show the preset channel number, if any, the frequency band and the station frequency. Indicators at the right side of the display show kHz when an AM station is tuned or MHz when an FM station is tuned.

ª Main Information Display: This

ten digit display shows messages relating to the status, input source, surround mode, tuner, volume level or other aspects of unit’s operation.

‚ Multi: This indicator signifies that

the AVR80IIis sending a program source to a remote room location. Note that it may be illuminated even when the unit is “off” in the main listening room, signifying that operation continues at another location. When a remote command is being received via the Multi IR connection, this indicator will flash.

⁄ Mode Status: These indicators

display the currently selected surround mode.

¤ DISP: This indicator lights when

the FL display has been turned off using the Display button ) to remind you that the unit is still turned on.

‹ Copy Indicators: The TAPE

indicator lights when an input

COPY

other than the current source has been selected to copy Tape1. The

VCR COPY1 indicator signifies that

the input to VCR1 is other than the currently selected source.

› P-Scan: This indicator flashes

when the stations programmed into the tuner memory are being automatically reviewed.

ﬁ Auto Memo: This indicator flash-

es when the tuner is automatically scanning for stations and entering them into the preset memory.

ﬂ Signal Level Indication: This is

a visual indication of the strength of a radio station signal. The more bars visible, the stronger the station.

Page 10

Rear Panel Audio and System Connections

OUT

TAPE2

MULTI

OUT

TAPE1

OUT

VCR2

FRONT

SWITCHED

AC OUTLETS (120V 60Hz)

CENTER

SURR.

8 OHMS

FRONT 8 OHMS

MAIN IN PRE OUT

SURR.

CENTER

SUB

WOOFER

DIGITAL

MULTI

OUT IN

REMOTE

CONT.

6-CH

DIRECT

INPUT

OUT

VCR1

FRONT

SURR.

CENTER

SUB

WOOFER

LR LR

AUDIO

SPEAKERS

VIDEO S-VIDEO

(75Ω)

ANTENNA

GND

MONI

OUT VCR2

OUT VCR1

UNSWITCHED

†

√

∑µñ

∫

∆

∂

å FM Antenna ∫ AM Antenna ç Tape 1 Out ∂ Tape 1 In é Tape 2 Out ƒ Tape 2 In © CD IN ˙ Front Right Speaker Output

î Front Left Speaker Output ∆ Center ˚ Surround Right Speaker Output ¬ Surround Left Speaker Output µ Subwoofer Pre-Out ñ Pre-Outs ø 6 Channel Direct Input π Multi Room Interface

œ Multi IR ® Multi-Out ß Power Cable † Switched AC Outlet ü Unswitched AC Outlet √ Remote IR In ∑ Remote IR Out

Page 11

Rear Panel Audio and System Connections

å FM Antenna: Connect an indoor or external FM antenna to these terminals.

∫ AM Antenna:Connect the AM loop antenna suppliedwith the receiver tothese terminals. If an external AM antenna is used, make connections to theAM and GND terminals in accordancewith the instructions supplied withthe antenna.

ç Tape 1 Out: Connect these jacks to the RECORD/INPUT jacks of an audio recorder.

∂ Tape 1 In: Connect these jacks to the PLAY/OUT jacks of an audio recorder.

é Tape 2 Out: Connect these jacks to the RECORD/INPUT jacks of a second audio recorder.

ƒ Tape 2 In: Connect these jacks to the PLAY/OUT jacks of a second audio recorder.

˙ Front R: Connect these terminals to the front right speaker.

î Front L: Connect these terminals to the front left speaker.

∆ Center: Connect these terminals to the center speaker.

˚ Surround R: Connect these ter- minals to the right surround speaker.

¬ Surround L: Connect these ter- minals to the left surround speaker.

µ Subwoofer Pre-Out: Connect this jack to the line level input of a powered subwoofer. If an external subwoofer amplifier is used, connect this jack to the subwoofer amplifier input.

ñ Pre-Outs: If external power amplifiers are used for any channels, remove the jumper pin and connect the jack to the input of the amplifier.

ø 6 Channel Direct Input: If an external digital audio decoder is used for 5.1 (Dolby Digital) audio, connect the outputs of that decoder to these terminals.

π Multi Room Interface: For multi- room installations where keypad remotes are in use, connect the keypad interface to this jack.

œ Multi IR: Connect the output of an IR sensor in a remote room to this jack to operate the AVR80II’s multiroom control system.

® Multi-Out: When using the AVR80IIfor multi-room audio, connect this jack to the input of the audio amplifier powering the remote room speakers.

ß Power Cable:Connect the AC plug to a non-switched AC wall output.

† Switched AC Outlet: This outlet may be used to power any device that you wish to have on when the unit is turned on.

ü Unswitched AC Outlet:This out- let may be used to power any AC device. The power will remain on at this outlet regardless of whether the AVR80IIis on or off.

NOTE: The power consumption of the device plugged into each of these outlets should not exceed120 watts.

√ Remote IR In: If the AVR80II’s front panel IR sensor is blocked due to cabinet doors or other obstructions, an external IR sensor may be used. Connect the output of the sensor to this jack.

∑ Remote IR Out: This connection permits the IR sensor in the receiver to serve other remote controlled devices. Connect this jack to the “IR IN” jack on Harman Kardon or other compatible equipment.

Page 12

Rear Panel Video Connections

OUT

TAPE2

MULTI

OUT

TAPE1

OUT

VCR2

FRONT

SWITCHED

AC OUTLETS (120V 60Hz)

CENTER

SURR.

8 OHMS

FRONT 8 OHMS

MAIN IN PRE OUT

SURR.

CENTER

SUB

WOOFER

DIGITAL

MULTI

OUT IN

REMOTE

CONT.

6-CH DIRECT INPUT

OUT

VCR1

FRONT

SURR.

CENTER

SUB

WOOFER

LR LR

AUDIO

SPEAKERS

VIDEO S-VIDEO

(75Ω)

ANTENNA

GND

MONI

OUT VCR2

OUT VCR1

UNSWITCHED

B A P M

G H

A VCR 1 Audio In B VCR 1 Audio Out C VCR 1 Video In D VCR 1 Video Out E VCR 1 S Video Out F VCR 1 S Video In G VCR 2 Audio Out

H VCR 2 Audio In I VCR 2 Video Out J VCR 2 Video In K VCR 2 S Video Out L VCR 2 S Video In M TV Audio In N TV Video In

O TV S Video In P LD Audio In Q LD Video In R LD S Video In S LD Digital In T TV Monitor Video Out U TV Monitor S Video Out

Page 13

Rear Panel Video Connections

A VCR 1 Audio In: Connect these jacks to the audio PLAY/OUT jacks of a VCR.

B VCR 1 Audio Out: Connect these jacks to the RECORD/IN audio jacks of a VCR.

C VCR 1 Video In: Connect these jacks to the composite video PLAY/OUT jacks of a VCR.

D VCR 1 Video Out: Connect these jacks to the composite video RECORD/IN jacks of a VCR.

E VCR 1 S Video Out: Connect these jacks to the “S” video RECORD/IN jacks of a VCR.

F VCR 1 S Video In: Connect these jacks to the “S” video RECORD/OUT jacks of a VCR.

G VCR 2 Audio Out: Connect these jacks to the audio jacks RECORD/IN of a second VCR.

H VCR 2 Audio In: Connect these jacks to the audio PLAY/OUT jacks of a second VCR.

I VCR 2 Video Out: Connect these jacks to the composite video RECORD/IN jacks of a second VCR.

J VCR 2 Video In: Connect these jacks to the composite video PLAY/OUT jacks of a second VCR.

K VCR 2 S Video Out: Connect these jacks to the “S” video RECORD/IN jacks of a second VCR.

L VCR 2 S Video In: Connect these jacks to the “S” video RECORD/OUT jacks of a second VCR.

M TV Audio In: Connect the audio outputs of a TV, cable converter or satellite receiver to these jacks.

N TV Video In: Connect the composite video output of a TV, cable converter or satellite receiver to this jack. The signals received at this jack are also used to trigger the “TV Auto-On” feature.

O TV S Video In: Connect the “S” video output of a TV, cable converter or satellite receiver to this jack.

P LD Audio In: Connect the audio output of a laser disc player to these jacks.

Q LD Video In: Connect the composite video output of a laser disc player to this jack.

R LD S Video In: Connect the “S” video output of a laser disc player to this jack.

S LD Digital In: Connect the coax digital output of a laser disc or CD player to this jack.

NOTE: This connection is for standard, two channel PCM audio. DO NOT connect the modulated RF digital output used for multichannel (AC-3) audio to this jack.

T TV Monitor Video Out: Connect this jack to the composite video input of a TV monitor or video projector to view the on screen control menus and output of the receiver’s video switcher.

U TV Monitor S Video Out:

Connect this jack to the S video input of a TV monitor or video projector to view S video sources selected by the receiver’s video switcher.

Page 14

Sending Learning

LearnUse

TV P/L

OFF ON OFF ON

3 ST MOVIE

LD MATRIX

THX

MONO HALL

CHANNEL/SKIP

REC

SELECT

SCREEN

DISPLAY

PANEL

SPEAKER

DISPLAY NOISE

TEST

ADJUST

DISC

DECK

ANT.

TUNE/SEARCH

MUTE

STOP

STEREO

VCR1

TV MAIN

DELAY 123

VCR2 6CH 456

AUX 789

AM/FM

Tape1

(MON)

Tape2

VOLUME

Source Power Main Power

MEMO CLEAR P•SCAN

a Use/Learn b Main Power c Source Selection d Source Power e Surround Mode Selection f Main Volume g TV Volume h Mute i Transport Controls

Remote Control Functions

j Tune/Search & Fast Forward k Channel/Skip l Disc/Deck/Ant m Number Keys n P-Scan o Memo p Delay q Menu Controls r Select

s Screen Display t Panel Display u Test Noise v Speaker Select w Level Adjust x Sending LED y Learn LED z 6Ch Direct

a Use/Learn: This switch selects

the operation mode of the remote control. Slide it to the left for normal operation. Slide it to the right when the remote is being programmed.

b Main Power: Press these buttons to turn the unit on or off.

c Source Selection: Pressing one of these buttons selects the input source that will be listened to through the receiver. When a source is selected the remote’s transport and numeric number buttons will also transmit the commands needed to control that machine.

d Source Power: Press these but- tons to control power for the last source device selected.

e Surround Mode Selection:

Press one of these buttons to select a surround mode for the current listening session.

f Main V olume: These buttons control the unit’s volume. Note that all channels are controlled simultaneously.

g TV Volume: These buttons adjust the volume for TV using the remote control codes programmed into the remote for a TV set or cable box. These buttons control the TV set only, regardless of which source is selected. This enables you to control the audio level of a TV set even when the receiver is not in use.

h Mute: Press this button to tem- porarily cut the audio output of the receiver. Press it again to return to the previous volume level.

i Transport Controls: These buttons control the tape or disc motion of the last playback source selected with the Source Selection buttons c. Use them as you would the Play, Stop, Pause, Reverse Play and Record buttons on any VCR, CD or LD remote control.

j Tune/Search & Fast Forward:

(These buttons have multiple functions, which vary according to the input device selected.)

Page 15

Remote Control Functions

a. When the TUNER has been

selected, these buttons are used to manually tune stations.

b. When CD, LD or VCR is the input

source, these buttons act as the Fast Scan Forward — or Fast Scan Reverse ‚ controls.

k Channel/Skip: (These buttons have multiple functions, which vary according to the input device selected.)

a. When the TUNER has been

selected, these buttons will scroll up · or down ‡ through the stations that have been programmed in the preset memory.

b. When TV or VCR is selected, they

are the channel up · or channel down ‡ tuning buttons.

c. When CD or LD is selected these

buttons act as forward and reverse “Skip” buttons to move to the next track or chapter on the disc.

d. When a compatible Harman

Kardon cassette player has been selected as Tape 1or Tape 2, these buttons move the tape forward · or backwards ‡ to the next selection using the Music Scan feature.

l Disc/Deck/Ant: (These buttons have multiple functions, which vary according to the input device selected.)

a. When CD is selected and the unit

is a CD changer, these buttons will change to the next disc ∏ or previous disc Â.

b. When Tape 1 or Tape 2 is the

input source, and the tape machine is a compatible Harman Kardon dual cassette deck, these buttons will switch between the “A” and “B” sides.

c. When VCR 1 or VCR 2 is the input

source, these buttons switch between VCR and TV as the unit’s output.

d. When TV is the input source,

these buttons may switch between video input sources or antenna/video, depending on the TV model.

e. When LD is the input source,

these buttons will switch the side being played from “A” to “B” on compatible dual side players.

m Number Keys: These buttons serve as a ten button numeric keypad to enter tuner preset positions. They are also to be used to select channel numbers when TV has been selected on the remote, or to select track numbers on a CD or LD player, depending on how the remote has been programmed. The letters below the buttons are used to enter information for tuner station names.

NOTE: The 0 button has a dual func- tion. It also serves as the CLEAR button to for use in programming the tuner or clearing the system memory.

n P-Scan: Press this button to automatically scan through the stations preset into the tuner memory. Press the button again to end the scan when the tuner stops at the desired station.

o Memo: The memo button is used to enter stations to the tuner’s preset memory in eitherthe manual or automatic modes. It is also used inthe process ofclearing the memory.

p Delay:This button controlsthe amount ofsound delay to therear (surround) channels.Press it to increase thedelay in the steps shown in themain Information Display or on-screen graphics.

q Menu Controls: These buttons control the action of the cursor or the selection of menu items when the receiver is being configured using the setup menus.

r Select: This button enters set- tings to the receiver’s memory during system configuration.

s Screen Display: Press this but- ton to activate the on screen menu system.

t Panel Display: Press this button to turn off all displays and indicators in the Information Display except for a small DISP indication in the lower right corner of the display ¤ Press the button again to turn the display back on. Note that the display will briefly illuminate when a command is sent to the unit from the front panel or remote, even though the display is turned off.

u Test Noise: Press this button to begin calibration of the output level for each channel. A test signal will immediately be heard from the left front speaker and the TEST indicator ™ will flash.

v Speaker Select: When setting the system output levels, this button selects the speaker position being adjusted. Press it once to advance to the next speaker after each position is adjusted.

w Level Adjust: When setting the system output levels, press these buttons in increase or decrease the output level.

x Sending LED: This indicator should flash any time a button is pressed to confirm that a command is being sent to the receiver or another unit. If the light is dim or does not illuminate when a button is pressed the batteries in the remoteshould be replaced.

y Learn LED: This indicator will illuminate when a button on the remote is being programmed with signals from another remote during the “learning” mode. The light will go out when the signal is received and memorized.

z 6 Channel Direct: When an external 5.1 digital audio decoder such as the ADP303 is connected, press this button to select that unit as an input source.

Page 16

Installation, Set Up & Configuration

System Installation

After unpacking the unit, and placing it in on a solid surface capable of supporting its weight, you will need to make the connections to your audio and video equipment. These steps need to be done only when the receiver is first installed, or when a change is made to the input source equipment.

Audio Input and Output Connections

Use the “Audio and Systems Connections” Diagram in the inside front cover as a guide to connecting audio components and speakers to the rear panel. We recommend that you use high quality cables when making connections to source equipment and recorders to preserve the quality of the signals.

NOTE: When making connections to audio source equipment or speakers it is always a good practice to unplug the unit from the AC wall plug. This prevents any possibility of accidentally sending audio or transient signals to the speakers that may damage them.

1. For playback only sources, such as a CD player, CD changer, external phono preamp or external digital to analog converter, connect the output jacks of the player to the appropriately labeled inputs on the rear panel. ©

NOTE: When the source device has both fixed and variable audio outputs it is best to use the fixed output unless you find that the input to the receiver is so low that the sound is noisy, or high that the signal is distorted.

2. When connecting recording devices such as cassette recorders, open reel tape decks, DCC, DAT or MD, connect the PLAY/OUT jacks of the recorder to the jacks ∂ƒ. Connect the RECORD/IN jacks on the recorder to the OUT jacks

çé.

3. Assemble the AM Loop Antenna supplied with the unit as shown below. Connect it to the AM and GNDscrew terminals ∫.

4. Connect an FM antenna to the

FM (75 ohm) connection å. The FM

antenna may be an external roof antenna, an inside powered or wire lead antenna, or a connection from a cable TV system. Note that if the antenna or connection uses 300 ohm twin lead cable, you must use the 300 ohm to 75 ohm adapter supplied with the unit to make the connection.

5. Connect the front, center and surround speaker outputs ˙î∆˚¬ to the respective speakers.

To assure that all the audio signals are carried to your speakers without loss of clarity or resolution, we suggest that you

use high quality speaker cable. Many brands of cable are available, and the choice of cable may be influenced by the distance between your speakers and this receiver, the type of speakers you use, personal preferences and other factors. Your dealer or installer is a valuable resource to consult in selecting the proper cable.

Regardless of the brand of cable selected, we recommend that you use a cable constructed of fine, multi-strand copper with a gauge of 14 or larger. Remember, that in specifying cable, the lower the number, the thicker the cable.

Cable with a gauge of 16 may be used for short runs of less than ten feet. We do not recommend that you use cables with an AWG equivalent of 18 or higher due to the power loss and degradation in performance that will occur.

One way to insure that cables will deliver a predictable level of performance is to use Home THX®certified cables. This certification assures that the cables have met a rigorous set of specifications designed for home theater applications.

Cables that are run inside walls should have the appropriate markings to indicate listing with UL, CSA or other appropriate testing agency standards. Questions about running cables inside walls should be referred to your installer or a licensed electrical contractor who is familiar with the NEC and/or the applicable local building codes in your area.

Page 17

Installation, Set Up & Configuration

When connecting wires to the speakers, be certain to observe proper polarity. Remember to connect the “negative” or “black” wire to the same terminal on the receiver and the speaker. Similarly, the “positive” or “Red” wire should be connected to the like terminal on the AVR80II and speaker.

NOTE: While most speaker manufacturers adhere to an industry convention of using black terminals for negative and red ones for positive, some manufacturers may vary from this configuration. To assure proper phase, and optimal performance, consult the identification plate on your speaker, or the speaker’s manual to verify polarity. If you do not know the polarity of your speaker, ask your dealer for advice before proceeding, or consult the speaker’s manufacturer.

6. Connections to a subwoofer are made via a line level audio connection from the receiver µ to the line level input of a subwoofer with a built in amplifier. If a passive subwoofer is used, the connection first goes to a power amplifier, which will be connected to one or more subwoofer speakers.

7. If an outboard multichannel digital audio adapter is used, connect the six outputs of the adapter to the 6 CH.

Direct Input inputs ø.

Video Input and Output Connections

Video connections are made in a similar fashion to those for audio components. Again, the use of high quality interconnect cables is recommended to preserve signal quality.

System and Power Connections

The AVR80II is designed for flexible use with external control components and power amplifiers. These connections are easy to make during an initial installation, or at a later date should you choose to upgrade your system.

1. Connect the VCR’s audio, video and “S” Video OUT jacks to the VCR IN jacks ACFHJL on the rear panel. The audio, video and “S” video IN jacks on the VCR should be connected to the

VCR OUT jacks BDEGIK on the

AVR80II.

Remote Control Extension

If the receiver is placed behind a solid or smoked glass cabinet door, the obstruction may prevent the remote sensor from receiving commands. In this event, an optional remote sensor may be used. Connect the output of the remote sensor

2. Connect the audio, video and “S”

to the Remote Cont. IN jack √. video outputs of a satellite receiver, cable TV converter or television set to the TV jacks MNO.

If other components are also prevented

from receiving remote commands, only

one sensor is needed. They may use this

3. Connect the audio, video and “S” video outputs of a Laser Disc player to the

LD jacks PQR. If your LD player has

a coax digital output for 44.1kHz PCM audio, you will obtain higher sound

unit’s sensor or a remote eye by running

a connection from the REMOTE

CONT.OUT jack ∑ to the Remote In

jack on Harman Kardon or other com-

patible equipment. quality by connecting that output to the

LD Digital In jack S.

4. Connect the TV MON T jacks on the receiver to the video or “S” Video inputs of your television monitor or video projector.

Page 18

Installation, Set Up & Configuration

CENTER

SURR.

8 OHMS

FRONT

8 OHMS

SPEAKERS

Subwoofer

Left Surround

Speaker

Right Surround

Speaker

–

MAIN IN PRE OUT

FRONT

SURR.

CENTER

SUB

WOOFER

External

Power Amplifier

CENTER

–

External Audio Power Amplifier Connections

Using the PRE OUT jacks ñ, connections may be made to external power amplifiers. To make these connections, remove the jumpers between PRE-OUT and MAIN IN, and save them for future use. Connect the PRE-OUT of the channels to be connected to external amplifiers to that amplifier’s inputs. Volume will still be controlled by this receiver.

When an external amplifier is used for the front channels, this receiver’s rear channel outputs and a passive (nonpowered) subwoofer may be connected to this unit’s internal amplifier for higher power output. To make these connections, follow the diagrams on this page. Using short RCA to RCA jumpers, connect the left and right SURR PRE-OUT jacks to the left and right FRONT MAIN

IN jacks. A subwoofer may be connected

by connecting the SUBWOOFER PRE

OUT to the CENTER MAIN IN.

If these connections are used, changes must be made to the speaker outputs. Connect the left and right surround speakers to the speaker terminals labeled

FRONT ˙î and the passive sub-

woofer to the speaker terminals labeled

CENTER ∆.

AC Power Connections

This unit is equipped with two accessory AC outlets. They may be used to power accessory devices, but they should not be used with high current draw equipment such as power amplifiers.

The SWITCHED † outlet will receive power only when the unit is on. This is recommended for devices that have no power switch, or a mechanical power switch that may be left in the “ON” position.

The UNSWITCHED ü outlet will receive power as long as the unit is plugged into a powered AC outlet.

Finally, when all connections are complete, plug the power cord into a nonswitched120 volt AC wall outlet. Note that the ring surrounding the Power Switch ( will turn amber. You’re almost ready to enjoy the AVR80II!

NOTE: When external power amplifiers are used, the center channel speakers should receive at least as much amplifier power as the front left and right speakers.

Page 19

Remote Control Programming & Operation

This productis equippedwitha powerful remote control.As supplied,itwill operate thereceiver,as well asmost CDplayers andtape decksmanufacturedby Harman Kardon.In addition,itis preprogrammed withthe remotecodesto operate VCRs,LD playersandTV setsthat are based onthe popularRC-5control code system. Ifyour equipmentrequiresdifferent codes,it maybeprogrammed tocopy the codesfrom mostinfrared remotes.

Loading Batteries

Thelifeof thebatteries forthe remote controlisabout oneyear innormal operation.Ifthe greenSending x indicatordoesnot flashwhen remotebuttons arepushed,that isan indicationthat the batteriesneedto bereplaced. Thebatteriesshouldbe removedif theremote will notbeused ofan extendedperiod of time.

To change the batteries:

1. Remove the back cover by sliding it in the direction of the arrows.

2. Remove the old batteries and insert fresh AAA type cells. Be certain to observe the correct polarity by noting the (+) and (–) marks on both the inside of the case and on the battery cells. It is recommended that both batteries be changed at the same time.

3. Close the cover until it clicks shut.

NOTE: It is important that the batteries be replaced within ten minutes after the old batteries are removed to avoid losing any remote codes that have been programmed into the remote’s memory.

Remote Control Range

The remote will operate at a range of up to 15 feet from the unit, when the batteries are fully charged. The remote will also operate at an angle of up to 30° to either side of the unit.

Always point the remote transmitter at the front of the unit when issuing commands. If you find that remote commands are not being received by the remote, it may be necessary to use a remote IR sensor.

Remote Programming

Programmable Keys

There are 63 buttons on the remote con-

trol that may be user programmed to

new functions to operate virtually any

component in your system. Ten CANNOT

be programmed with a new code, as they

control high level functions of the

AVR80II. These keys are Main Power

ON, Main Power OFF, and the eight

source input keys: TV, LD, VCR 1,

VCR2, TUNER, CD, TAPE 1 and

TAPE2.

Programmable keys are divided into two

groups. Some keys may be programmed

with a separate function for each of the

inputs. Thus, these keys may change

their code when the input source is

changed. (i.e. The Play key may trans-

mit a different code when CD is selected

as opposed to when VCR is selected.)

The keys that may be programmed with

multiple codes are the following:

All Numeric Keys (0 – 9) Forward Play Source Power On Reverse Play Source Power Off Stop Disc/Deck ∏ Record Î Disc/Deck Â Pause ± Channel/Skip · TV Volume Up ⁄ Channel/Skip ‡ TV Volume Down ¤ Tune/Search — Memo Tune/Search P-Scan

ﬂ

ﬁ

‚

Page 20

Remote Control Programming & Operation

Another group of keys may only be programmed with one remote code. The code contained in these keys remains the same regardless of the source selection.

WARNING:These keys transmit codes that are vital to the operation of the product. It is not recommended that they be programmed with alternative codes, as it may then be impossible to operate certain functions of the receiver.

THX Aux Cursor Up Pro Logic Delay Cursor Down Dolby 3 Stereo Memo Cursor Right › Movie Screen Display Cursor Left ‹ Matrix Panel Display Select Hall Speaker Main Volume Up Stereo Test Noise Main Volume Down Mono Adjust Mute 6Ch Direct

⁄

Toprogram theremote, followthese steps. Notethatit isnot necessaryto program allkeys,only thosethat arerequired to operatethesubject device.Keys notprogrammedwillretain thecodes preprogrammedatthe factory.

1. Slide Use/Learn a switch at the top left corner of the remote to the right so that it is next to Learn.

2. If one of the multi-function buttons is being programmed press the source button (i.e. CD, VCR, etc.) you wish to have this function associated with. If you are programming a single function key, proceed to the next step.

3. Press the button on the remote that is to be programmed. Note that the

Learning y LED will illuminate.

4. Place the remote head to head with the remote control whose function is being learned. The two remotes should be no more than 8 inches apart.

5. Press and hold the button on the remote corresponding to the function to be memorized until the Learning LED starts to blink. When the LED goes out, release the button on the transmitting remote. The function code has been successfully captured by the remote.

NOTE: If both LEDs flash during a programming operation, it indicates that the remote’s memory is full or that the remote codes from the transmitting remote are not compatible with the unit’s signal format.

6.Continueto programany additional remotecommandsrequired usingsteps 2through5. Whenyou havefinished programmingtheremote, slidethe

Use/Learn switchto theleft sothat it

isinthe Useposition.

Clearing the Remote Memory

In normal operation, codes for a new

device may be programmed “over” the

codes that have been previously pro-

grammed into the remote. It is also pos-

sible to clear the memory for individual

keys, or for the entire remote. When a

memory position is cleared, the remote

will return to the original factory preset

command.

To clear the memory for a specific indi-

vidual key location, put the Use/Learn

switch in the Learn position. Press the

Main Power Offb button and the

button to be cleared at the same time.

Both the Sending and Learningindi-

cators will light momentarily. When the

lights go out, the memory has been

cleared of the user programmed code

and returned to the factory preset. Return

the Use/Learn a switch to the Use

position when you are finished.

To clear the remote’s entire memory

and return all keys to their factory preset

commands first put the Use/Learn a

switch in the Learn position. Then press

the Main Power Onbutton b and

confirm that the Learning indicator

y has illuminated. While continuing

to press the Power Onbutton, press and

hold the Power Offb button until the

Learn indicator goes off for about 3 sec-

onds. It will then blink twice. Then

release the two buttons. This indicates

that the memory has been cleared of any

user programmed commands and that

the original commands have been

restored. Slide the Use/Learn switch

back to the Use a position to return

the remote to normal operation.

Page 21

System Configuration

Right Front Speaker

Left Front

Speaker

No more than 24"

Center Front Speaker

Right Front Speaker

Left Front

Speaker

Center Front

Speaker

Right Front Speaker

Left

Front

Speaker

No more

than 24"

Center Front

Speaker

When all audio, video and system connections have been made, there are a few configuration adjustments to be made. A few minutes spent to correctly configure and calibrate the unit will greatly add to your listening experience.

Speaker Selection and Placement

The placement of speakers in a multi channel home theater system can have a noticeable impact on the quality of sound reproduced. For Home THX operation it is recommended that the speakers

The AVR80II may be used with either conventional (point source) surround speakers or with THX Certified diffuse surround speakers. No adjustment is needed to select the type of surround speaker used.

Speaker Placement

Depending on the type of center channel speaker in use and your viewing device, place the center speaker directly above or below your TV or in the center behind a perforated front projection screen.

carry the certification mark of Lucasfilm Ltd.’s Home THX Division. However, with careful selection and placement, the AVR80II will deliver accurate reproduction with any high quality speakers.

Once the center channel speaker is installed, position the left and right front speakers so that they are as far away from one another as the center channel speaker is from the preferred listening

No matter which type or brand of speakers are used, the same model or brand of speaker should be used for the front left, center and right speakers. This creates a seamless front soundstage, and elimi-

position. Ideally, the front channel speakers should be placed so that their tweeters are no more than 24” off center form the tweeter in the center channel speaker.

nates the possibility of distracting sonic disturbances that occur when a sound moves across mis-matched front channel speakers.

Depending on the specifics of your room acoustics and the type of speakers in use, you may find that imaging is improved by moving the front left and right speak-

For the most accurate and exciting reproduction of bass frequencies a sepa-

ers slightly forward of the center channel speaker. If possible, adjust all front loud-

rate subwoofer should be used. When THX Certified front channel speakers are used, a separate subwoofer is mandatory, as THX front and center speakers are not designed for extreme low frequencies.

A) Front Channel Speaker Installation

with Direct View TV Sets or Rear Screen

Projectors

B) Front Channel Speaker Installation with

Non-Perforated Front Projection Screen

C) Front Channel Speaker Installation with Center Speaker behind a Perforated Front Projection Screen

Page 22

System Configuration

TV or Projection Screen

Left Front

Speaker

speakers are used

when rear-mounted

No more than 6 feet

The distance between the left and right speakers should be equal to the distance from the seating position to the viewing screen. You may also experiment with placing the left and right speaker slightly forward of the center speaker.

Center Front

Speaker

Optional Rear Wall Mounting

At least 6 inches from ceiling

At least 2 feet

Right Front

Speaker

speakers so that they are aimed at ear height when you are seated in the listening position.

Using these guidelines, you find that it takes some experimentation to find the correct location for the front speakers in your particular installation. Don’t be afraid to move things around until the system sounds correct. Optimize your speakers so that pans across the front of the room sound smooth, and that sounds from all speakers appear to arrive at the listening position at the same time without delay from the center speaker as opposed to the left and right speakers.

Note that some THX Certified center channel speakers must be placed vertically, while others may be placed horizontally. Consult the instruction manual accompanying your center speaker for the correct mounting position.

Surround speakers should be placed on the side walls of the room, at or slightly behind the listening position. The center of the speaker should face into the room with the active speaker drivers pointing towards the front and rear of the room. The speakers should be located so that the bottom of the cabinet is at least two feet higher than the listeners’ ears when in the desired area.

If side wall mounting is not practical, the speakers may be placed on a rear wall, behind the listening position. Again, they should be located so that the bottom of the cabinet is at least two feet higher than the listeners’ ears. The speakers should be no more than six feet behind the rear of the seating area.

Subwoofers produce non-directional sound, so they may be placed almost anywhere in a room. Subwoofer placement is highly influenced by room size

and shape, and the type of subwoofer

used. Follow the instructions of the sub-

woofer’s manufacturer, or experiment

with the best location for a subwoofer in

your listening room.

Once the speakers have been placed in the

room and connected, the final step is to

enter the configuration information and

balance the speaker output levels. Before

proceeding further this is a good time to

review the installation section of the

manual to make certain that all connec-

tions are properly made.

System Settings

1. Plug the unit into an AC wall outlet

and press the Powerbutton on either

the front panel ( or the remote b.

Note that the ring surrounding the front

panel switch will turn green, and the

front panel display will illuminate.

2. Turn on the TV connected to the

receiver. Select the appropriate video

input on the TV.

NOTE: Although the unit will switch “S”

video signals, the on screen menus con-

trol system is NOT visible on the S video

output.

3. Press the SCREEN DISPLAY s

button, and then press any of the naviga-

tional arrow buttons or the SELECT

r button on the remote to bring the

MAIN MENU up on your video screen.

(Figure #1)

4. Press the ¤ button five times until

the on screen >cursor is pointing to

SET UP MENU.

5. Press SELECT r to move to the

next screen, SET UP MENU 1.

(Figure #2).

Page 23

System Configuration

INPUT SELECTOR REC OUT SELECTOR SURROUND MODE TEST TONE MULTI ROOM SEL:OFF SET UP MENU

MENU OFF

MAIN MENU

CENTER MODE >LARGE SMALL NONE SUB WOOFER ON OFF GO TO SET UP MENU 2

RETURN TO MAIN MENU

SET UP MENU 1

MULTI RM VOL >VARIABLE FIXED SET LEVEL ÐXXdB

SET UP LOCK LOCK UNLOCK RETURN TO MAIN MENU

SET UP MENU 2

OFF >ON

TEST TONE

6. The first item to be set is the Center Channel Mode. The on screen >cursor will already point toward this option when you select the menu. Press the

‹ or › buttons q to choose one of

these center channel options by moving the cursor:

LARGE: Choose this option if you are

using either a THX Certified speaker system with a subwoofer or large size full range center channel speaker.

SMALL: Choose this option if the cen-

ter speaker is small sized.

NONE: Choose this option if you are

not using a center channel speaker.

7. When the center channel speaker selection is complete, press the ¤ button

q to move to the next option. Note that

the on screen >cursor will move down to

SUBWOOFER.

8. Press the ‹ or › buttons q to choose one of these options:

ON: Choose this option if a Subwoofer

is installed. Selecting this option routes all low frequency information (below 80Hz) to the subwoofer output.

OFF: Choose this option if no

Subwoofer is present.

9. Press ¤qonce and then SELECT

r to move to SET UP MENU 2 to contin-

ue the set-up procedure. (Press ¤ twice and then SELECT if you prefer to return to the MAIN MENU.)

10. At SET UP MENU 2 (Figure #3) you are able to establish settings for multiroom operation and lock the control settings. You may skip these menus by pressing ¤

q until the on screen

to RETURN TO MAIN MENU and pressing

SELECT r.

cursor is next

11. If multiroom operation will be used, the first option enables you to select the method used for volume control. With the >cursor pointing to MULTI RM VOL press the ‹ or › buttons to choose one of these options:

VARIABLE: Choose this option if the

volume control in the remote rooms will be controlled by a remote control and a sensor connected to the AVR80II via the MULTI IR input on the rear panel.

FIXED: Choose this option if there is

no remote control link to the remote rooms, or if you wish to have the volume in these rooms remain at a fixed, constant level.

12. When you have made your selection, press ¤ q to move to the next option,

SET LEVEL. Press the ‹ or › buttons

q to set the volume in accordance with

the option chosen in the previous menu:

a. If you selected VARIABLE Volume Set, this option selects the volume level at the remote rooms when the system is first turned on in those locations.

b. If you selected FIXED Volume Set, this is the level that will remain constant in the remote rooms.

13. When you have made a volume selection, press ¤ q to move to the next option. Note that the >cursor should point to SET UP LOCK.

14. This option enables you to lock the settings at the SET UP MENU 1. This makes it difficult for someone to inadvertently change the settings by causing the word LOC K to appear at the top of SET

UP MENU 1. Before any further changes

Figure 1

Figure 2

Figure 3

Figure 4

Page 24

System Configuration

are made, the user must first go to SET

UP MENU 2 and unlock the system.

Press the ‹ or › buttons q to choose one of these options:

LOC K: Choose this option to lock the

settings as described above.

UNLOCK: Choose this option unlock

the settings and enable them to be changed without going to this menu.

15. When you have made your choice, press ¤ q and then SELECT r to return to the main menu. At this point the output levels for all channels will be set to a reference so that the sound level is the same from each speaker. This compensates for the differences between the speakers used and the distance each speaker is from your listening position.

Atthis pointyou maywish toadjust the rearchannel delaytime. Seethe Advanced Featuressection laterin thismanual for informationon delaysettings.

NOTE: Before setting the output levels it is critical that the front panel bass ˝ and treble controls ˆ be set to their center, or “12 o’clock” position. This ensures accurate results.

16. Atthe MAIN MENU,press ¤ three (3) timesuntil the>cursor isnext to

TEST TONE.Press SELECT to

continue.

17. When you press SELECT you will immediately hear a test noise from the front right speaker. The on screen display will change to a graphic representation of each of the speakers in your room, with one speaker position blinking. (Figure #4) That speaker is the one whose level is being set.

NOTE:Thisprocedure willonly operateif the AVR80IIis in the THX,PRO LOGIC,

MOVIE orDOLBY 3 STEREO Modes.

Ifthe test tone cannot be selected,check toseewhich surroundmode isindicated inthefront paneldisplay.If itis not one ofthefour modesmentioned above,press the ‹ button to cancel the test procedure. Selectoneof thecorrect modes,and then move the cursor to test tone to re-start the procedure.

18. While seated in the primary listening position, you should hear a test noise signal from the left front speaker. You may leave the volume setting where it is, or raise it to an appropriate level using the

ADJUST ⁄ or ADJUST ¤ w but-

tons on the remote. For a more precise calibration, we recommend that you use a sound pressure level meter, as described at the end of this section.

19. Press SPEAKER v on the remote. Note that the sound should now come from the Center Channel speaker, and the icon for that speaker will flash on the screen. Use the ADJUST ⁄ and

ADJUST ¤ buttons w on the remote

to change the level of the test noise so that it appears to be equal in level to the Front Left speaker.

20. Press the SPEAKER button again, and repeat the procedure for the Front Right, Surround Right, Surround Left and Subwoofer channels. Each time, use the ADJUST ⁄ and ADJUST ¤ buttons w on the remote to change the volume level so that all speakers match, and the press SPEAKER v to move to the next channel.

NOTE: This test also serves as an opportunity to verify that all speakers are properly connected. If the sound from a

speaker location does not match the

location shown on the video and front

panel displays, turn the AVR80II off and

check the speaker wiring to make certain

that the speaker is connected to the

correct output terminals.

21. When all speakers appear to have an

equal volume, press the ‹ button q on

the remote to complete the procedure.

For a more accurate calibration of the

speaker output levels perform the test

outlined in steps 18 through 21 using a

sound pressure level (SPL) meter. For

calibration to THX standards, it is recom-

mended that the output for each channel

measure 75 dB (C-weighted, slow) on the

meter. An inexpensive SPL meter may be

purchased from Radio Shack stores as

the model 32-2050 or 32-2055.

NOTE: You may also check the output

levels at any time by pressing the TEST

NOISE button u. When the on screen

display is also activated by pressing

SCREEN DISPLAY s, you will see

the speaker icons and level information

superimposed on your video screen.

Follow the instructions in steps 18

through 20 above to calibrate the system,

and press the TEST NOISE button u

again to cancel the test.

CONGRATULATIONS! You have complet-

ed a basic set up and you are now ready

to enjoy the finest in home theater and

music listening enjoyment.

Page 25

Basic Operation

Oncetheinput, speakerand antennaconnectionshavebeen made,and thesystem hasbeenconfigured, thereceiver isready foroperation.Note thatsome controlsare duplicatedonboth thefront paneland theremotecontrol, whileothers appear ononeor theother,but notboth.

Power Switch

Toturnthe AVR80IIon forthe firsttime, pressthe frontpanel POWERbutton (.

Note that the front panel will light up and the unit will return to the last input source selected and the front panel displays will illuminate. If the unit is connected to a TV set the current operating conditions will appear briefly on screen.

Once the unit has been turned on with the front panel switch it may then be turned on and off for future use using the Main Power b buttons on the remote. Note that the remote power will NOT operate unless the Power button has first been manually depressed.

When the AVR80 is turned off using the remote control the unit is in a STANDBY mode, and the Standby LED will illuminate in amber. The unit may be turned back on from the standby mode by pressing either the Main Power button

b or any of the Sourcebuttons

on the remote or front panel

345678c.

NOTE: When the power switch is in the “OFF” position the unit is in a “Standby” mode and is NOT disconnected from the AC mains power.

Source Selection

To select or change the input source, press one of the Source buttons on the front panel 345678 or one of the Source buttons on the remote c.

NOTE: Once you have programmed your remote control with the proper infrared commands for your TV set, a “Power On” command will automatically be sent to the TV when you select the TV input using the remote control.

To listen to one source while you watch another, first select the video source (LD,

TV, VCR1, VCR2 or Aux), and then

select the desired audio source (AM/FM

CD, Tape 1, Tape 2).

NOTE: When the unit is in “standby” mode, pressing any of the source buttons will turn on the unit.

The audio source will be displayed on the Information Display, while the video source will be displayed in the upper left corner of the Fluorescent Display next to the word VISUAL ¡.

Volume Control

The AVR80II’s volume is controlled using either the front panel knob * or the

MAIN VOLUMEbuttons f on the

remote. If the volume control is set too high, a

speaker overload may activate the unit’s protective circuitry. This will cut the output to the speakers and change the LED surrounding the power switch to a red color. To clear the problem, turn the unit off for a few seconds, and lower the volume before turning it back on. If the problem re-occurs, turn the unit off and consult your dealer or an authorized service center for advice.

NOTE: Unlike conventional mechanically driven volume controls, this receiver’s volume is set using digital devices. This means that the volume knob has no firm stopping point at either end of its rotation. Depending on the speed with which the knob is turned, it is normal for as many as three complete rotations to be

required for full travel from the loudest

setting to the softest.

When the volume is adjusted, the word

Master will appear in the main portion

of the Information Display, followed by a

two digit number. The number indicates

the variation from the reference point

established when the output levels are

set.

Surround Mode Selection

One of the most important features of

the AVR80II is its ability to reproduce a

full multichannel surround soundfield

from both surround encoded programs,

and standard stereo programs. In addi-

tion, this is one of the few receivers avail-

able that is equipped for Home THX, the

ultimate in home theater. In all a total of

eight listening modes are available on

the AVR80II.

Selection of a surround mode is based on

personal taste, as well as the type of pro-

gram source material being used. For

example, motion pictures bearing the

logo of one of the major surround encod-

ing processes, such as Dolby Surround,

DTS Stereo or UltraStereo may be played

in either the THX Cinema, Dolby Pro

Logic or Movie Surround Modes. TV or

radio broadcasts of programs in sur-

round, but not originally produced as

theatrical motion pictures should be

played back in the Dolby Pro Logic or

Movie Surround modes. Other mode

selections are described elsewhere in this

manual.

NOTE: Once a program has been encod-

ed with surround information, it retains

the surround matrix as long as the pro-

gram is broadcast in stereo. Thus, movies

with surround sound will carry surround

information when they are broadcast via

conventional TV stations, cable, pay TV

Page 26

Basic Operation

and satellite transmission. In addition, a growing number of made for television programs, sports broadcasts, radio dramas and music CDs are also recorded in surround sound. You may obtain a list of these programs and discs from Dolby Laboratories Licensing Corp., 100 Potrero Avenue, San Francisco, CA 94103.

Surround modes may be selected in one of three ways.

From the front panel, use the Mode⁄ or Mode¤ buttons # to scroll through the list of modes. The selected mode will appear in large letters in the front panel display, and in a two line reminder on the video screen. Once the selection is made, the mode will continue to appear in a smaller indictor at the bottom of the front panel display.

IMPORTANT NOTE:Many people incorrectly presume that sound should always be heard from the surround channels. In reality, it is normal for the surround channels to operate occasionally, and often to be silent. Movie directors and sound mixers typically use these channels only when needed to create an effect or establish ambience. Artificially increasing the volume level to the surround channels may destroy the illusion of carefully controlled audio effects and add unwanted noise to your system.

From the remote, modes may be selected by simply pressing the button that corresponds to the desired mode. e

Modes may also be selected using the on screen display. Press SELECT r on the remote to display the MAIN MENU. Then press ¤ q twice so that the on screen cursor is next to SURROUND

MODE. Press SELECT r again to

move to the next menu.

At the SURROUND MODE MENU, press the ‹ or › buttons r until the desired mode name appears on the screen. Press

¤ twice until the > cursor is next to

RETURN TO MAIN MENU and press SELECT. At the main menu select

MENU OFF and press SELECT to exit

the menus. A different mode may be selected for

audio and video sources. Once a mode has been selected, it will be attached to those sources in memory. Thus, you may select THX CINEMA as the mode for video and HALL SURROUND for audio. After the initial selections made, the unit will automatically return to your preferred mode for each type of input whenever it is chosen.

TV Auto Function

With the increasing sophistication of today’s home entertainment systems, it often takes numerous remote controls to turn on all components in a system. This receiver’s unique “TV Auto On” function greatly simplifies that task and reduces the actions needed to bring your entire system to life.

If you are using a TV or projector that has video output, and you wish to use the output of its tuner as an audio source for the AVR80II, connect the TV’s audio and video outputs to the rear panel of the AVR80II. MN Once those connections are made, the AVR80II will automatically turn on whenever the TV set is on, thanks to a video sensing circuit in the AVR80II. This eliminates the need to turn the unit on separately from the TV.

As long as the TV is on and feeding a video signal, the AVR80II will remain on. If no other input source is selected and the TV is turned off, the AVR80II will turn off approximately five minutes after the TV set.

If you select another input, such as CD or

the AM/FM turner after the unit has

turned on, it will remain on even if the

TV is turned off. You must then turn the

receiver off using the front panel or

remote POWERbuttons. b(

NOTE: The TV Auto On Function will

only respond to conventional video sig-

nals. It will NOT operate with S-Video.

IMPORTANT NOTE: If you do not

have a video source connected to the TV

VIDEO N input, or do not wish to use

this feature, it is important that you dis-

able it. To disable the TV Auto on feature

press the TV and Memo 7Ú buttons

on the front panel at the same time.

Hold them for a few seconds until the

front panel information display shows

TV AT ON. Immediately release both

buttons and then quickly press the TV

button 7 again. The front panel display

will read TV AT OFF. Release the

button to complete the system change.

Should you wish to reactivate the feature

again in the future, press the buttons

as shown above and then press the TV

button until the display again reads

TV AT ON.

Tuner Operation

The FM/AM tuner is extremely flexible,

and offers a number of options. The

following instructions will enable you

to take advantage of the tuner’s many

features.

To select tuner operation, press the

AM/FM button £ on the front panel,

or the remote c. Press the button again

to select the desired frequency band if

required.

Manual up/down tuning is accessible

by pressing the TUNE button ^ either

up ⁄ or down ¤ or the Tune/Search

‚ and Tune/Search —

j buttons on the remote. Pressing

these buttons once increases or decreases

Page 27

Basic Operation

the station frequency by one step. Holding the buttons down quickly scans for the next station. Holding the tune buttons for a few seconds and then releasing them will set the tuner to the next station with an acceptable signal.

When manually tuning stations, observe the SIGNAL LEVEL indicator ﬂ and the TUNED ∞ indicators. The more bars visible on the SIGNAL LEVEL indicator, the stronger the signal and the better the station will sound. A station is properly tuned when the TUNED indicator is illuminated.

Tuner Mode

Pressing theFM Mode buttonÙ on the front panelselects howastation willbe received. Whenthe buttonispressed so that theAUTO ¢ indicatoris lit,stations broadcastingin stereowillbe received instereo. Youmay notestereo broadcasts byobserving thatthe

STEREO § indicator will illuminate.

When theFM Mode buttonÙ is pressed untilthe AUTO ¢ light goes out, allstations willbereceived ina monaural moderegardless ofthemethod of transmission.

NOTE: When a station is broadcasting in stereo, but has a weak signal level, the reproduction may not be acceptable. In this case, select the Auto Off mode, as monaural reception is less susceptible to noise in weak reception areas.

Tuner Presets

There are thirty preset positions may be used to store your favorite stations in any order. These may be used to memorize both the station’s frequency, reception mode and a name. Stations may be preset automatically or manually, and then recalled in a variety of ways.

Automatic Station Preset Selection

This process automatically scans the AM and FM bands and enters all stations with proper signal strength into the memory. To automatically preset the tuner’s memory, follow these steps:

1. Select the tuner as the unit’s input by pressing the AM/FM button 3c.

2. Using the TUNE ^jbuttons, select the first station you wish to preset at the low end of the AM or FM band.

3. Start the automatic tuning preset by simultaneously pressing MEMO and

TUNE ⁄ on the front panel Ú^or

remote oj. The station tuned in step #2 will be entered into the tuner’s memory as CH 1. The MEMO £ and

AUTO MEMO ﬁ indicators will flash.

The display will show increasing frequencies to indicate that the auto scan is in progress.

4. Each time the tuner finds a station the scanning will pause and the station will be played for five seconds. During this time you have the following options:

a. To enter the station in the next open memory position, no action is needed. After five seconds the tuner will enter the station and the preset number will be visible at the far left side of the main information display.

b. The frequency band may be changed by pressing the FM/AM button 3c.

c. If the tuner is scanning FM stations, the MODE may be changed from AUTO to mono by pressing the

FM MODE button Ù.

d. If you do not wish to enter the current station into the preset memory, press the TUNE ⁄ button ^j on the front panel or remote.

5. After the desired action is completed,

or five seconds elapse, the tuner scan will

continue. The operation will stop auto-

matically when all 30 preset positions are

filled or when both frequency bands have

been completely tuned, whichever comes

first. To stop the automatic preset process

at any time press the CLEAR button Û

or any input selection button.

Manual Tuner Preset

Stations may be manually entered into

the tuner’s memory in any order. Manual

entry is performed from the remote con-

trol only.

1. Tune to the desired station as outlined

in Tuner Operation Section.

2. Press the MEMO button Úo and

note that the MEMO indicator £ will

flash.

3. While the indicator is flashing for the

next 5 seconds, enter a number from 1 to

30 using the number buttons on the

remote m. Any number may be used,

but if another station has already been

programmed into the location number

selected, the previous setting will be lost.

a. To enter a single digit memory location, press 0 before the number, or enter the number and wait a few seconds.

b. If an invalid number (other than 1–30) is entered in error, the display will flash to alert you that the entry is invalid and it will return to the previous frequency display.

4. When the preset memory has been

properly programmed the MEMO indica-

tor £ will stop blinking.

Page 28

Basic Operation

Station Name Preset

In addition to identifying stations by their broadcast frequency, each preset station may be assigned a name using alphanumeric characters. This enables you to identify a station by its call letters, program format, or any other five character phrase.

To enter a station name, first preset all stations you wish to program into the tuner’s memory. Then, follow these steps:

1. Tune to the desired preset station.

2. Press the MEMO button Ú on the front panel for more than three seconds.

3. Note that a character on the left side of the main information display will start to blink.

4. Enter the first character of the name using either the front panel TUNE ⁄ or

¤ buttons ^ or the alphanumeric but-

tons m on the remote. A. To use the front panel buttons simply

press and hold TUNE ⁄ ^ button until the desired letter or number appears. Note that the upper case alphabet will appear, followed by the numbers

1 through 0, and then a

blank space. Tapping the button will

indicating a

advance the display one character at a time; holding it down will move the display quickly. If you pass by the desired character, use the TUNE ¤ ^ to move the display in reverse.

After entering the first character, press

MEMO Ú to move to the next position

and note that the next digit will blink. Use the same procedure outline above to enter a character.

When you have entered a digit or “blank” in all five spaces, press MEMO

Ú to confirm the entry

B. To use the remote for character entry, press the button corresponding to the desired letter or number. Press it once to enter the first printed letter, twice for the second, three times for the third and four times for the number. Press the “9” button to enter a blank space. (For example, press the “ABC” button once to enter an “A”, three times for a “C” and four times to enter a “1”.)

Use the MEMO button o to move to the next digit position. When all five spaces have been filled, press MEMO again to confirm the entry.

Once a station name has been attached to a preset position, the station’s frequency will appear briefly when the unit is tuned to that station. After a few seconds the preset name will appear in the display.

Tuning Preset Stations

Stations preset into the tuner’s memory may be recalled in a number of ways.

1. To recall a station directly enter a number from 1 to 30 using the number buttons on the remote s m .

a. To enter a single digit memory location, press 0 before the number, or enter the number and wait a few seconds.

b.Ifan invalidnumber (otherthan 1–30)isentered inerror,that number willflashto alertyou thatthe entry is invalidandthe displaywill returnto thepreviousfrequency display.

2. To scan through the list of preset stations, press the P-SET⁄ or P-SET ¤ button on the front panel $. Press once to move up or down thorough the memory presets one by one, or press and hold the button to quickly scan through the list of stations.

3. To automatically review each station

in the memory, press the P-SCAN but-

ton n%. Note that the P-SCAN indi-

cator › will blink.

4. The tuner will move up through the

list of stations, pausing to play each for

five seconds. Note that preset numbers

where no station has been programmed

will be skipped.

5. When the desired station is reached

press P-SCAN % or CLEAR Û.

Clearing Preset Stations

Once stations are programmed into the

preset memories, it is possible to remove

them individually or as a group.

To remove a single station from the

memory:

1. Recall the station by pressing the but-

tons on the remote corresponding to the

station’s memory location.

2. Press the MEMO button Ú or o

and observe that the MEMO indicator £

will blink.

3. While the indicator is blinking, press

the CLEAR button Û within five sec-

onds. The word CLEAR will show briefly

to confirm that the memory position has

been cleared.

To clear allmemory locations, the

volume level and surround mode

memories:

1. Press the MEMO button Úoand

the CLEAR button Ûmat the same

time.

NOTE: When a complete memory clear is

performed the AVR80II will turn off as

part of the process. After clearing the

memory it is necessary to reset all sta-

tions and set up parameters.

Page 29

On Screen Display

AUDIO SOURCE : TUNER VIDEO SOURCE : VCR2 TAPE1 OUT : CD VCR1 OUT : AUX

MODE : DOLBY PRO LOGIC MULTI ROOM:TUNER MASTER VOLUME ЩЩЩЩЩЩЩЩЩЩЩЩЩЩЩ||РР

MODE :THX CINEMA DELAY TIME:20msec

<COPY FUNCTION> TAPE OUT:TUNER VCR1 OUT:VCR2

<FUNCTION SELECT> AUDIO:TUNER VIDEO:VCR1

FRONT L : +1 dB FRONT R : Ð2 dB

CENTER : +5 dB

SURROUND L : Ð10 dB SURROUND R : +3 dB

SUB WOOFER : 0 dB

On Screen Menus

In addition to the information shown on the front panel display, it is also possible to obtain the unit’s current status through the use of on screen video messages. The on screen menus may also be used to control many aspects of the receiver and to make adjustments and selections.

To activate the On Screen display system, press and hold the SCREEN DISPLAY

s button on the remote for three sec-

onds. This will cause a status summary display to be shown on the screen for ten seconds. (Figure #5). Once the video displays are enabled, this status screen will also appear when the unit is turned on.

NOTE: In order to view the on screen menu displays the receiver must be connected to the standard, composite video input of a TV monitor or projector. The on screen displays are NOT visible via the “S” video output.

The status screen displays the following information:

AUDIO SOURCE: This is the input

currently selected for audio.

VIDEO SOURCE: This is the input

currently selected for video.

TAPE1 OUT: This is the source cur-

rently routed to the Tape 1 audio output for recording.

MODE: This is the currently selected

audio/surround mode.

MULTIROOM: This is the source cur-

rently selected for listening in remote room locations.

MASTER VOLUME: This is the cur-

rent volume level. Note that volume appears as a horizontal scale. The “0dB” reference level is indicated by a solid block Í, while volume levels above or below the reference are indicated by double vertical bars ±.

Function Displays and Messages

Once the On Screen Displays have been activated, they appear when certain functions are performed from the front panel buttons or the remote control. These messages are three line displays with the current function shown on the top line and information about the selection or choice on the bottom two lines.

The following function/operation display screens are available:

Surround Mode and Delay

When the surround mode is changed or the delay timing is adjusted, this message will appear at the bottom of the video screen. The top line is the surround mode, the bottom line is the delay time for that mode. (Figure #6) Note that delay time will not be displayed in the

MONAURAL, STEREO or DOLBY 3 STEREO modes, as these modes do not

have rear channel information.

Figure 5

Figure 6

Figure 7

Figure 8

VCR1 OUT: This is the source cur-

rently routed to the VCR 1 video output for recording.

Figure 9

Page 30

On Screen Display

MASTER VOLUME ЩЩЩЩЩЩЩЩЩЩЩЩЩЩЩ||РР

MUTE

ON SCREEN DISPLAY

ÐOFFÐ

>TAPE *TUNER*

VCR1 *LD*

RETURN TO MAIN MENU

REC OUT SELECTOR

>AUDIO *LD*

VIDEO *LD* TAPE MONITOR ON

OFF

RETURN TO MAIN MENU

INPUT SELECTOR

Input Selection

When the source input is changed, this message will appear (Figure #7). The top line is the audio input source, the bottom line is the video input source. Remember, when choosing an input, select the video source first, and then the audio source if a split input/simulcast listening session is desired. Note that when the TAPE

COPY function is engaged, the AUDIO

source is displayed in reverse video.

Tape Copy Input Selection

When an input is selected for either

TAPE1 or VCR1 copy, the choices

appear as a message with the TAPE1 information on the top line and the VCR1 information on the bottom line. (Figure #8)

Surround Output Levels

To obtain a status screen with the outputs for each individual channel, press the

SPEAKER button v on the remote. A

summary will appear for ten seconds. (Figure #9)

Master Volume

When the volume is changed, a horizontal scale will briefly appear at the bottom of the screen with the volume level. (Figure #10)

Mute

When the unit is placed in audio mute, the word MUTE will appear in the upper right corner of the screen as a reminder that the volume has been cut. (Figure #11)

On Screen Display Function

If you do not wish to have the on screen displays appear, press and hold the

SCREEN DISPLAY button s on the

remote for three seconds. A reminder message will appear on the screen for a few seconds (Figure #12), and the displays will then be canceled until they are once again activated.

NOTE: Additional display messages appear as a part of the Multiroom system. These are described in the portion of this manual dealing with that topic.

Using The On Screen Menus for System Control

Besides conveying status messages, the on screen display system may also be used as a means of controlling the operation of the unit. To operate the control system, always start by pressing

SELECT r on the remote to bring up

the Main Menu. (Figure #1). Then, use the up/down navigational arrow keys ⁄ and ¤ q to move the cursor. Press

SELECT r to choose a menu, and

then use the left/right navigational arrow keys ‹ and › q to view the choices in that current option. Finally, when the desired choice appears, press SELECT

r to enter the choice and return to the

MAIN MENU. To exit from the Menu

Control System, press ¤ q until the on screen > cursor is pointing to MENU

OFF and press SELECTr.

Figure 10

Figure 11

Figure 12

Figure 13

Figure 14

Page 31

On Screen Display

>TAPE *SOURCE*

VCR1 *SOURCE*

AUDIO *TUNER*

VIDEO *LD*

RETURN TO MAIN MENU

REC OUT SELECTOR

>MODE :THX CINEMA

DELAY TIME :20ms

RETURN TO MAIN MENU

SURROUND MODE

The following functions of the AVR80II may be controlled through the Menu Control System:

INPUT SELECTION: After reaching

the INPUT SELECTOR menu (Figure #13), use the arrow keys on the remote

q to select the desired input.

Remember that when a split listening session is desired, select the VIDEO source first, followed by the AUDIO source. To use the Tape Monitor, press the down arrow button ¤ q to move the on-screen cursor. Use the ‹ and › arrow buttons to turn the Tape Monitor On or Off.

RECORD OUT SELECTION: After

reaching the REC OUT SELECTOR menu (Figure #14) use the navigational arrow keys to select the input to either

TAPE 1 or VCR 1. Note that if the cur-

rent main input SOURCE is chosen, two more lines will appear on the screen to remind you which audio and video sources are selected. (Figure #15).

TEST TONE: At this menu you may

adjust the speaker output levels. For information on this procedure, refer to the System Configuration section of this Manual.

MULTI-ROOM SEL: For information

on configuring and using the multiroom audio functions of the AVR80II, consult the appropriate section of this Manual.

SET UP MENU: For information on

using the Set Up menus, refer to the System Configuration section of this Manual.

Figure 15

Figure 16

SURROUND MODE: After reaching

the SURROUND MODE menu (Figure #16), use the navigational arrows q to select the desired mode. When a mode is selected that uses the surround channels, you may change the rear channel

DELAY TIME at this menu.

Page 32

Advanced Features

In additionto basicaudiofunctions, this receiver iscapable ofbothsophisticated audio/video dubbingand awiderange of surround modes.Advanced digitalsignal processing providesspecialized surround modes thatare compatiblewithvirtually all typesof musicsoftwareand movie soundtracks.

For theultimate insoundreproduction, the AVR80IIis equipped fordigital input from laserdisc orCDplayers witha coaxial digitaloutput, sothatthe sound reaching thesurround processorcomes directly fromthe disc.

Finally, theAVR80IIis prepared forthe future withprovisions forconnectionto outboard multichannel (Dolby Digital and DTS)digital audiodecoders.

Audio Tape Dubbing

The inputto theaudiorecorders isnormally thesource currentlyselectedfor listening throughthe AVR80

II. Ifyou are

using atape recorderorcassette deck with threeheads andwishto listento the “off tape”playback toverifythe recording, pressthe frontpanelT-MON 5 button orthe TAPE 1 (MON)c but- ton onthe remoteuntilthe redlight over

T-MON onthe frontpanel illuminates.

Youwill then hearthe sourceas it is being recordedand playedbackthrough your tapemachine. Thesourcewill be verified inboth thefrontpanel andon screen displays.Note thatthe videosurrounding theword AUDIO willturn white toindicate thatyouare inthe Tape Monitor mode.

Torecord oneinput source whileyou listen toanother selectthedesired output by pressingthe frontpanelRecord Out

Tape-1copy button. Each pressof

the buttonwill changetheoutput tothe tape recorderin thefollowingorder:

SOURCE ‡ TUNER ‡ CD ‡ TAPE 2 ‡ SOURCE

Once theinput isselectedyou may change theinput forthemain listening system withoutfear ofdisturbingthe recording aslong as theAVR80II‘spower is on.

NOTE: Itis notpossibleto selectone of the videoinputs (VCR1,VCR2, LD,

AUX) asa directrecording source using

the RecordOut select button.Tomake an audiorecording fromoneof these sources firstselect thedesiredsource as the maininput, andthenuse the

Record OutTAPE 1 button to

select

SOURCE .

Video Dubbing

Videodubbing is similarto that foraudio recording, withchanges toaccommodate the requirementsof recordingbothan audio andvideo source.Forvideo recording itis importanttonote thatthe output to VCR1 only isselected withthefront panel switch.The outputtoVCR2 is always setto thecurrentinput source. (Unless thatSource isVCR2, in which case theVCR2 recordoutput is blank.)

Toselect inputsfor VCR dubbinguse the

VCR1 COPYbutton Ò onthe front

panel. At thefirst pressofthe button,a status

display willappear onboththe front panel displayand theonscreen video menus (Figure#8) toremindyou that the inputsource currentlyinuse isalso being routedto theVCR1 output.If this is acceptable,no furtheractionis required.

Torecord asource other thanthe input, press theVCR1 COPY buttonagain, and notethat thedisplaywill changein the followingorder:

SOURCE ‡ TV ‡ LD ‡ VCR 2 ‡ AUX ‡ SOURCE

Press thebutton untiltheinput youwish to recordappears. Youmay nowchange

the mainlistening inputwithoutfear of

disturbing therecording aslongas the

unit’spower remainson.

NOTE: Inputsources foreitherthe audio

or videotape outputsmayalso beselect-

ed usingthe onscreenvideo menusys-

tem describedelsewhere inthismanual.

Audio/Video Simulcast Recording

Itispossible torecord thevideo from one

sourcealongwith theaudio froma differ-

entinput.This isuseful inthe case of

musicalprogramswhere thesound is

beingbroadcastvia FM,or forsports

eventswhereyou wishto havethe picture

fromaTV station,but theplay-by-play

fromaradio station.

Tocreate asimulcast recording first

select thevideo sourceinput(

VCR2,AUX) usingthe input selection

TV, LD,

buttons onthe remotecontrolor front

panel. 78c Next, selecttheaudio

source (FM/AM, CD orTAPE)

3456 .Note thattheon screenon

screen menudisplay willshowthe split

sources (Figure# 7).Thefront paneldis-

play willshow theaudiosource inlarge

letters inthe mainportionof the

Information Display,while the video

source willappear insmallerletters next

to theVISUAL ¡ indicator.Once the

split sourceis configured,select

SOURCE asthe inputforVCR1 by

pressing theVCR1 COPY button.

Input sourcesfor VCR1 COPYdubbing

may alsobe madeusingthe onscreen

video menusystem.

Delay Time Adjust

One aspectof thesurroundmodes isthe

delay ofaudio signalsbetweenthe front

speakers andthe rearspeakers.Each sur-

round modeis factorypresetwith aspe-

cific delaytime, butitis possibleto

individually adjustthe delaytimingto

custom tailorthe soundtoyour individ-

Page 33

Advanced Features

ual tasteand theacousticconditions in your listeningroom orhometheater.

The factorysetting isappropriatefor most rooms,but someinstallationscreate anuncommon distancebetweenthe front andsurround speakersthatmay cause thearrival offrontchannel sounds to becomedisconnected fromsurround channel sounds.

Tore-synchronize thefront and surround channels, followthese steps:

1. Measurethe distancefromthe listening/viewing positionto thefront speakers.

2. Measurethe distancefromthe listening/viewing positionto thesurround speakers.

3. Subtractthe distancetothe surround speakersfrom thedistanceto the frontspeakers andadd15. The resulting numberis theidealdelay time foryour room.Forexample, if thefront speakersare10 feetaway and thesurround speakersare5 feet away,the formula willbe “10–5+15=20”. Thus,the correct delay timein thisroomwould be 20ms.

NOTE: Thedelay timemayonly be adjusted incertain modes.

If thedelay timeneedsto bechanged, it maybe increasedbypressing the

DELAY button@pon thefront

panel. Thedelay timewillbe briefly displayed onthe videomenusas wellas the frontpanel.

In additionto theuseof thedelay time formula, itis agoodidea tounderstand the featuresof each ofthe AVR80II’ssurround modeswhen enteringdelaytime. The charton thenextpage providesan explanation ofthe suggestedforeach mode. Thechart alsocontainsthe delay time limitsfor eachofthe modes.

Direct Digital Decoding

The AVR80II’s digitalsignal processing uses sophisticatedmicroprocessors and advanced digitalaudio enginesthat manipulate soundin thedigitaldomain. In orderto workwithsound, thesecircuits mustfirst converttheincoming analog audioinput toadigital signal. After processing,the digitalaudiosignal must beconverted backtoanalog forvolume controland amplification.

While thedigital toanalog(D/A) and analog todigital (A/D)circuitsin the AVR80II arehigh quality, anytime an audio signalis digitizedorreconstructed to analogthere isthepossibility ofquality loss.This helpsyouto avoidun-needed A/D andD/A conversionfromany laser disc playerequipped withacoaxial digital output.

If yourplayer hasthistype ofoutput, connect theLD player tothe AVR80II with ahigh qualitydigitalor coaxinterconnect. Theconnection shouldbemade to theLD DIGITAL IN jack S on the rear panel.

Once thisconnection ismade,the AVR80II willaccept the digitaloutput directly fromyour LDplayer.Toselect the direct digitalinput, presstheLD button

7c andhold itforthree seconds.This

means thataudio signalswillremain in their puredigital stateuntilafter allsurround processinghas takenplace.

NOTE: Thisconnection isfor standard twochannel 44.1kHzPCM digitalaudio, asprovided byLDor CDmachines. Itis NOTan inputformultichannel digital audiosignals suchAC-3or DTS.Improper connectionto thewrongtype ofdigital outputmay causedamageto theAVR80II orother componentsinyour audiosystem andare notcoveredby theAVR80IIwarranty. Consultyour dealeror installerif youhave anyquestionsabout thisinput.

6 Channel Direct Operation

Since 1993,an increasingnumberof

theatrical motionpictures havebeen

recorded withdigital soundtracks.

With thesenew processessuchas Dolby

Surround Digital™, DTS®and Sony’s

SDDS®, five ormorediscrete sound

channels areavailable alongwitha dedi-

cated subwooferchannel forlowfrequen-

cy sounds.The replacementofanalog

matrix theatricalaudio, suchasDolby

Stereo withthese newsystemshas greatly

increased theenjoyment ofmoviesound.

Advances inelectronics technologynow

make itpossible tobringthese discrete

digital audiosoundtracks intoyour

home. Manyof today’snew LDplayers

and anincreasing numberofLD movie

releases providefor DolbyDigitalsound-

tracks. Inthe future,highdefinition tele-

vision (HDTV)broadcasts willalsocarry

multichannel digitalaudio information.

Toprevent yourAVR80IIfrom obsoles-

cence, specialjacks areprovidedfor use

with externalmultichannel audio

adapters.

If anadapter suchasthe Harman

Kardon ADP303is installedinyour sys-

tem, connectits sixanalogaudio outputs

to the6-CH DIRECT INPUT jacksø

on theAVR80II’srearpanel.

When listeningto programsusingan

external adapter,press the 6-CH

DIRECT buttonzÔ ontheremote or

front panel.All surroundprocessingwill

be disabledwhen 6ChannelDirect isin

use, asnone isrequiredwith discrete

audio signals.Volume iscontrolled inthe

normal fashion.

NOTE: Audioreproduced fromthe

6 ChannelDirect inputsmaynot be

recorded.

Page 34

Surround Mode Chart

Advanced Features

MODE

DOLBY PRO LOGIC

THX CINEMA

DOLBY 3 STEREO

MOVIE SURROUND

FEATURES

Dolby Pro Logic is the standard mode for surround sound decoding. It uses information encoded in a two channel stereo recording to produce four distinct channels: Left, Center, Right and Surround. Use this mode for accurate reproduction of programs bearing the Dolby Surround, DTS Stereo, UltraStereo or other “Surround” logos. Surround encoded programs include videocassette and LD movies, TV and cable programs, radio programs and audio CDs. Dolby Pro Logic processing may also be used to provide a pleasing surround effect with source material that does not carry surround encoding.

THX Cinema is a patented process developed by Lucasfilm Ltd. as an enhancement to surround processing. It includes additional enhancements that greatly improve the spectral and spatial realism of motion pictures that are recorded with surround encoding. THX Cinema’s exclusive processing is designed to overcome the differences in acoustics between movie theaters and home listening rooms so that movie sound tracks will sound the same way at home as they did in the mixing room where they are created. Use this mode when viewing motion pictures on video.

Dolby 3 Stereo uses the information contained in a surround encoded program to create center channel information. In addition, the information that is normally sent to the rear channel surround speakers is carefully mixed in with the front left and right channels for increased realism. Use this mode when you have a center channel speaker, but no surround speakers.

Movie Surround uses decoding similar to Pro Logic, but it permits delay times up to 90 ms. Use this mode instead of Pro Logic or THX to experiment with surround times above 30 ms, or if the delay time formula suggests a larger time delay for your room.

DELAY TIME RANGE

15 ms – 30 ms Initial Setting = 20 ms

No Surround Channels

40 ms – 90 ms Initial Setting = 20 ms

HALL SURROUND

MATRIX SURROUND

MONO

STEREO

This mode is designed for use with stereo recordings. It provides a sound field effect that simulates the complex combination of direct and reflected sounds that create the rich reverberant atmosphere of a medium sized circular concert hall.

This mode is designed for use with sports broadcasts, live concerts or other programs where the feeling of a wide surround effect is desired.

This mode is intended for use with old movies, televisions shows and other programs that have a monaural sound track. All sound will be reproduced through the center channel speaker, if installed. If there is no center channel speaker, monaural sound is reproduced from the front left and right speakers.

This mode turns off all surround processing and presents the pure left and right channel presentation of two channel stereo programs.

10 ms – 90 ms Initial Setting = 20 ms

No Surround Channels

Page 35

Multiroom Operation

The AVR80II is unique among A/V receivers in that it is equipped to operate as the control center for a sophisticated multiroom operation with accessories as simple as a remote IR sensor or as sophisticated as a specialized external amplifier and a special version of the world-famous AudioAccess wall mounted keypad controls. Although some multiroom installations will require the services of a specially trained installer, it is possible for the average do it yourself hobbyist to install a simple remote room system. For additional information on using the AVR80II in multiroom installations we suggest that you contact your dealer or custom installer.

Installation

The key to remote room operation is to link the remote room to the AVR80II’s location with wire for an infrared receiver and speakers or an amplifier.

IR Link

The remote room IR receiver should be connected to the AVR80II via standard coaxial cable. Plug the IR connection cable into the mini jack inside the Multi area in the middle of the AVR80II’s rear panel.œ

If other Harman Kardon compatible source equipment is part of the main room installation, the REMOTE CONT.

OUT jack on the rear panel ∑ should

be connected to IR IN jack on the CD player or cassette deck. This will enable the remote room location to control

source equipment functions as well as the remote room input and volume.

NOTE: All remotely controlled components must be linked together in a daisy chain. Connect the IR OUT jack of one unit to the IR IN of the next to establish this chain.

Audio Link

Depending on the distance from the AVR80II to the remote room, two options are available.

The preferred method is to run high quality, shielded audio interconnect cable from the AVR80II’s location to the remote room. At the remote room, connect the interconnect cable to a stereo power amplifier. The amplifier will be connected to the room’s speakers. No volume control is required, as the AVR80II and the remote IR link will provide that function. At the AVR80II, plug the audio interconnect cable into the MULTI OUT jacks ® at the top left corner of the AVR80II’s rear panel.

NOTE: The remote power amplifier must have signal sensing capability or be left on constantly to assure automatic operation at the remote room.

As an alternative, the amplifier may be

placed at the same location as the

AVR80II, with a standard audio intercon-

nect between the two. Speaker wires

should then be run to the remote room.

High quality AWG-12 speaker wire is pre-

ferred.

IMPORTANT NOTE:Any cables run

inside wallsshould be CL3/FT4rated, or

carry anyother certification thatis

required bythe NEC, NFPAor state and

local buildingand electrical codes.To

avoid interference,audio and speaker

cables shouldnot be parallelto, or in

the sameconduits with ACcables. If you

have anyquestions about multi-room

wiring consultyour dealer,custom

installer ora licensed contractoror

electrician.

Set-up

Once the equipment connections have

been made, the AVR80II needs to be con-

figured for multiroom operation by fol-

lowing these steps:

1. Press the SELECT r to bring the

MAIN MENU to the screen (Figure #1).

Press the ¤ button q four times until

the on screen >cursor is pointing to

MULTI ROOM SEL and press

SELECT r. The video screen

will movetothe MULTI ROOM

SELECTOR menu (Figure #17).

2. Press the › button q until the

desired input source for the multi room

system is selected.

Page 36

Multiroom Operation

MULTI ROOM SELECTOR

>SELECTED:TUNER TV CD LD TAPE1 VCR1 OFF TAPE2 VCR2 AUX

RETURN TO MAIN MENU

TURN MULTI-ZONE OFF

USERS MAY BE LISTENING

IN OTHER ROOMS

PRESS AGAIN TO PROCEED

OR "CLEAR" TO CANCEL

3. When the source is selected, press the

¤ button until the

RETURN TO MAIN MENU. Press

SELECT.

cursor is next to

4. At the MAIN MENU, press the ¤ button once so that the >cursor is pointing to SET UP MENU. Press SELECT.

5. This will bring SET UP MENU 1 (Figure #2) to the screen. Press the ¤ button twice until the >cursor is pointing to GO TO SET UP MENU 2. Press

SELECT.

6. When SET UP MENU 2 (Figure #3) appears, the >cursor will be pointing to

MULTI RM VOL. Use the ‹ or ›

buttons q on the remote to select one of the following choices.

a. If the remote room is equipped with a remote receiver only, volume control will be performed by the AVR80II using a remote control in the second room. For this type of control, select the VARIABLE option.

b. If the volume control in the remote room will be controlled by the amplifier in the remote room, or if a specialized amplifier such as the AudioAccess AVX-603 will be used, select FIXED.

7. After making a selection, press the ¤ button once so that the >cursor is next to SET LEVEL.

8. Use the ‹ or › buttons q on the remote to establish a volume level for turn on or constant level, as determined by the previous selection.

a. If VARIABLE volume has been selected, this setting will determine the volume level for the remote room each time it is turned on.

b. If FIXED volume has been selected, this level will be the constant volume level at the remote room location unless a local volume control is installed. Set the level as close to “0dB” as possible without distorting the output signal.

9. When the level has been entered, press the ¤ button so that the >cursor is pointing to RETURN TO MAIN MENU and press SELECT.

10. At the MAIN MENU, use the navigational arrow buttons on the remote to exit from the main system.

The AVR80II is now configured for multi room operation.

Operation

Multi room operation is simple, and it may be controlled from either the main listening room where the AVR80II is located, or from a remote room where an IR receiver or AudioAccess keypad has been installed.

Main Room Operation

In this option, the remote room feed is controlled from the main listening room using the AVR80II’s front panel controls.

Toactivate theremote roomfeed, press theMULTIbutton onthe frontpanel 9. Thiswillsend thesignal ofthe AVR80II’s currentlyselectedinput sourceto the remoteroomat thevolume levelestablishedinSET UP MENU 2.

Figure 17

Figure 18

Page 37

Multiroom Operation

The MULTI indicator on the front panel display ‚ will flash to indicate that the multiroom system is turned on in the variable mode, and that Source Linking is in effect. With Source Link, any change to the AVR80II’s input selection will also change the feed to the remote room locations. If the input source is changed from the remote room, the MULTI indicator will remain lit, but stop flashing.

If the AVR80II is turned off in the main listening room, the feed to the remote room will continue, although the

MULTI indicator will now remain con-

stantly illuminated. To turn off the feed to the remote room

either while the AVR80II is still on, or after it is turned off, press the MULTI button on the front panel. If the MULTI button is pressed while the AVR80II is still on and the on screen video system is engaged, a warning message will appear on the video display (Figure #18) to remind you that people may still be lis-

tening to the system in the remote room location.

Remote Room Operation

In this option, the remote room feed is controlled by the use of an AVR80II compatible remote control. The remote commands must be transmitted to the AVR80II via a coaxial link connected to the MULTI input on the AVR80II’s rear panel.

Using the remote control in the second room press the POWER ONbutton to turn on the remote room feed. This will activate the multi room portion of the AVR80II whether or not it may be on in the main listening room.

The initial feed to the remote room will be the last station selected by the tuner. Any other AVR80II input source may subsequently be selected using the source buttons on the remote control.

The initial volume at the remote room

will be the level established using the

options in SET UP MENU 2.

If IR connections have been made to the

source playback equipment, it is also

possible to control the functions of those

units via the second room remote.

Consult with your dealer or custom

installer for additional information on

this type of installation.

When the remote room is controlling the

AVR80II via the IR link, the MULTI

indicator on the AVR80II’s front panel

will remain constantly lit.

NOTE: Whenever the AVR80IIis in a

multiroom mode, the MULTI indicator

will flash briefly whenever a command is

transmitted by the remote room location

and received by the AVR80II.

Memory Backup

This product is equipped with a memory backup system that preserves tuner presets and system configuration information if the unit is accidentally unplugged or subject to a power outage. This memory will last for approximately one week, after which time all information must be re-entered.

System Reset

In therare casewhere the unit’soperation orthe displaysseem abnormal, the cause mayinvolve theerratic operation of the system’smemory or microprocessor.

To correct this problem, first unplugthe unitfromthe ACwall outletand wait at leastthreeminutes. Afterthe pause, reconnecttheAC powercord andcheck the unit’s operation. If the system still malfunctions, a system reset may clear the problem.

To clear the entire system memory of the unit, press and hold the

CLEAR Û buttons until CLEAR MEMO

appears in the front panel display. Release the buttons and note that the unit will turn off. Remember that once you have cleared the memory in this

MEMO Ú and

fashion it will be necessary to re-establish

all system configuration information

and tuner presets.

Ifthesystem isstill operatingincorrectly,

theremayhave beenan electrostaticdis-

chargeorsevere ACline interferencethat

hascorruptedthe memoryor micro-

processor.

If a reset does not solve the problem, con-

sult an authorized Harman Kardon ser-

vice depot.

Page 38

Troubleshooting Chart

Troubleshooting

SYMPTOM

No front panel lights when power switch is pressed

Display lights, but no sound or picture

No sound from any speaker. Light around power switch is red

No sound from surround or center speakers

No On Screen Control Menus

Unit does not respond to remote commands

CAUSE

• No AC Power

• Intermittent input connections

• MUTE is on

• Volume control is down

• Amplifier is in protection mode due to possible short

• Amplifier is in protection mode due to internal problems

• Incorrect surround mode

• Input is monaural

• Incorrect configuration

• TV input is “S” Video

• Weak batteries in remote.

• Remote is in LEARN position

• Remote sensor is obscured

SOLUTION

• Make certain AC power cord is plugged into a live outlet.

• Check to see if outlet is switch controlled.

• Make certain that all input and speaker connections are secure.

• Press MUTE button.

• Turn up volume control.

• Check speaker wire connections at receiver and speaker ends for shorts.

• Contact your local Harman Kardon service depot.

• Select a mode other than Stereo or Monaural.

• There is no surround information from mono sources.

• Check configuration inSET UP MENU 1.

• Change TV input to Composite Video. The menus are available ONLY on Composite Video.

• Change remote batteries.

• Slide USE/LEARN switch to USE.

• Make certain front panel sensor is visible to remote.

Intermittent buzzing in tuner

• Local interference

• Move unit or antenna away from computers, fluorescent lights, TVs, motors or other electrical appliances.

Page 39

Technical Specifications

Audio Section

Stereo Mode Continuous Average Power (FTC)

100 Watts per channel 20Hz–20kHz: @ < 0.07% THD, both channels driven into 8 Ohms

Five Channel Surround Mode Continuous average power per channel (FTC)

Front L&R channels: 85 Watts per channel from 20Hz–20KHz, @ < 0.05% THD, both channels driven into 8 Ohms

Center channel: 85 Watts from 20Hz–20kHz, @ < 0.05% THD, driven into 8 Ohms

Surround channels: 60 Watts per channel from 40Hz–20kHz, @ < 0.05% THD, both channels driven into 8 Ohms

Input Sensitivity/Impedance

Linear 220mV/50 Kohms Front Main In 1.5 V/20 Kohms Center Main In 1.5 V/20 Kohms Surround Main In 1.0 V/20 Kohms

Signal to Noise Rate (IHF-A)

Linear 95 dB

Dolby Surround Channel Separation 40dB

Frequency Response

@ 1W (+0, –3dB) 7Hz–80kHz

High Instantaneous Current Capability (HCC) ±45 amps

Transient Intermodulation Distortion (TIM) Unmeasurable

Rise Time 16µsec Slew Rate 40 V/µsec

FM Tuner Section

Frequency Range 87.5–108.0MHz Usable Sensitivity IHF 1.3 µV/13.5dBf Signal to Noise Ratio Mono/Stereo 76/68dB Distortion Mono/Stereo 0.2/0.5% Stereo Separation 1 kHz 40dB A.C.S. ±400kHz 65dB Image Rejection 98MHz 50dB Tuner Output Level 1kHz, ±75kHz Dev 800mV

AM Tuner Section

Frequency Range 520–1710kHz Signal-to-Noise Ratio 50dB Usable Sensitivity Loop 500µV Distortion 1kHz, 30% Mod 0.5% Selectivity ±20kHz 70dB

Video Section

Television Format NTSC Input Level/Impedance 1Vp-p/75ohms Output Level/Impedance 1Vp-p/75ohms Video Frequency Response 10Hz to 8MHz (–3dB) S/N 65dB

General

Power Requirement AC 120V 60Hz Power Consumption 54W idle, 700W maximum Dimension (Max)

Width 17.4 inches (444 mm) Height 6.4 inches (160 mm) Depth 18 inches (459 mm) Weight 31 lbs. (14 kg)

All features and specifications are subject to change without notice. Manufactured under license from Dolby Laboratories Licensing Corporation.

Additionally licensed under Canadian patent number 1,037,877. “Dolby,” “Pro Logic.” the double-D symbol and “AC-3” are registered trademarks of Dolby Laboratories Licensing Corporation.

Manufactured under license from Lucasfilm Ltd. U.S. patent numbers 5,043,970; 5,189,703; and 5,222,059. Foreign patents pending. THX and Home THX are registered trademarks of Lucasfilm Ltd.

DTS is a trademark of Digital Theater Systems SDDS is a registered trademark of Sony Corp.

Page 40

AM•FM CD T•2T•MON TV LD VCR1 VCR2 AUX

ClearPhonesPower Memo

VCR1Tape-1

Record Out

6-ch direct mode

VISUA

SIGNAL LEVEL

STEREO

Printed in Japan Part #1111-AVR80II

260 J851260

Harman Kardon AVR80II Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual