Harman Kardon AVR 170/230C User Guide

AVR 1700, AVR 170, AVR 170/230C
Audio/video receiver
Owner’s Manual
AVR
Table of Contents
INTRODUCTION 3 SUPPLIED ACCESSORIES 3 IMPORTANT SAFETY INFORMATION 3 PLACE THE AVR 3 FRONT-PANEL CONTROLS 4 REAR-PANEL CONNECTORS 6 SYSTEM REMOTE CONTROL FUNCTIONS 8 INTRODUCTION TO HOME THEATER 10
PLACE YOUR SPEAKERS 10
PLACING THE LEFT, CENTER AND RIGHT SPEAKERS 10 PLACING THE SURROUND SPEAKERS 10 PLACING THE SUBWOOFER 10
TYPES OF HOME THEATER SYSTEM CONNECTIONS 11
MAKING CONNECTIONS 13
SET UP THE REMOTE CONTROL 16
INSTALL THE BATTERIES IN THE REMOTE CONTROL 16 PROGRAM THE REMOTE TO CONTROL YOUR SOURCE
SET UP THE AVR 17
OPERATING YOUR AVR 19
ADVANCED FUNCTIONS 23
2
AVR
Introduction, Supplied Accessories, Important
Safety Information and Place the AVR
English
Introduction
Thank you for choosing this Harman Kardon® product!
For more than fifty years, the Harman Kardon mission has been to share a passion for music and entertainment, using leading-edge technology to achieve premium performance. Sidney Harman and Bernard Kardon invented the receiver, a single component designed to simplify home entertainment without compromising performance. Over the years, Harman Kardon products have become easier to use while offering more features and sounding better than ever.
The AVR 1700, AVR 170 and AVR 170/230C 5.1-channel digital audio/video receivers (AVRs) continue this tradition with some of the most advanced audio and video processing capabilities yet and a wealth of listening and viewing options.
To obtain the maximum enjoyment from your new AVR, please read this manual and refer back to it as you become more familiar with its features and their operation.
If you have any questions about this product, its installation or its operation, please contact your Harman Kardon retailer or custom installer, or visit our Web site at www. harmankardon.com.
Supplied Accessories
The following accessory items are supplied with your AVR. If any of these items are missing, please contact your Harman Kardon dealer, or Harman Kardon customer service at www.harmankardon.com.
• System remote control
• EzSet/EQ
• AM loop antenna
• FM wire antenna
• Three AAA batteries
• AC power cord
microphone
IMPORTANT SAFETY INFORMATION
Verify Line Voltage Before Use
The AVR 1700 has been designed for use with 120-volt alternating current (AC). The AVR 170 and AVR 170/230C have has been designed for use with 220 – 240-volt AC. Connection to a line voltage other than that for which your AVR is intended can create
a safety and re hazard, and may damage the unit. If you have any questions about
the voltage requirements for your specific model or about the line voltage in your area, contact your selling dealer before plugging the unit into a wall outlet.
Do Not Use Extension Cords
To avoid safety hazards, use only the power cord supplied with your unit. We do not
recommend that extension cords be used with this product. As with all electrical devices, do not run power cords under rugs or carpets, or place heavy objects on them. Damaged
power cords should be replaced immediately by an authorized service center with a cord
meeting factory specifications.
Handle the AC Power Cord Gently
When disconnecting the power cord from an AC outlet, always pull the plug; never pull the cord. If you do not intend to use your AVR for any considerable length of time, disconnect the plug from the AC outlet.
Do Not Open the Cabinet
There are no user-serviceable components inside this product. Opening the cabinet may
present a shock hazard, and any modication to the product will void your warranty. If
water or any metal object such as a paper clip, wire or staple accidentally falls inside
the unit, disconnect it from the AC power source immediately, and consult an authorized
service center.
CATV or Antenna Grounding (AVR 1700)
If an outside antenna or cable system is connected to this product, be certain that it is grounded so as to provide some protection against voltage surges and static charges. Section 810 of the United States National Electrical Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit, connection to grounding electrodes and requirements of the grounding electrode.
NOTE TO CATV SYSTEM INSTALLER: This reminder is provided to call the CATV (cable TV) system installer’s attention to article 820-40 of the NEC, which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as possible.
Place the AVR
• Place the AVR on a rm and level surface. Be certain that the surface and any mounting
hardware can support the AVR’s weight.
• Provide proper space above and below the AVR for ventilation. Recommended
clearance distances are 30cm above the unit, 30cm behind the unit and 30cm on each side of the unit.
• If you install the AVR in a cabinet or other enclosed area, provide cooling air within the
cabinet. Under some circumstances, a fan may be required.
• Do not obstruct the ventilation slots on the top of the AVR or place objects directly
over them.
• Do not place the AVR directly on a carpeted surface.
• Do not place the AVR in moist or humid locations, in extremely hot or cold locations, in
areas near heaters or heat registers, or in direct sunlight.
3
AVR
Front-Panel Controls
Front-Panel Controls
Power Indicator/
Power Button
Tuning Mode Button/
RDS Button
Channel
Level Control
Button
IR
Sensor
Set
Button
Left/Right
Buttons
Message
Display
Up/Down Buttons/
Tuning Buttons
Surround Mode
Select Buttons
Headphone Jack/
EzSet/EQ Mic
Connector
Source Select
Buttons
Volume
Knob
Aux Analog Audio Input
Connector
Digital Input
Button
4
Surround-Mode Category Button
USB Port
AVR
Front-Panel Controls, continued
English
Front-Panel Controls, continued
Power indicator/Power button: The AVR has four different power modes:
Off (Power indicator not illuminated): When the rear-panel Main Power switch is
in the Off position or the power cord is unplugged the AVR is off and will not respond to any commands. Plugging the power cord into a live AC outlet and setting the Main Power switch in the On position will put the AVR into the Eco Standby mode.
Eco Standby (Power indicator glows solid amber): The Eco Standby mode minimizes
energy consumption when you're not using the AVR. When the AVR is in Eco Standby, it will not automatically turn on or play audio in response to an AirPlay signal from a networked device. When the AVR is in Eco Standby, pressing the Power button turns it on. To put the AVR into Eco Standby when it is on, press the Power button for more than three seconds. NOTE: The AVR will not automatically enter the Eco Standby mode.
Standby (Power indicator glows solid amber): The Standby mode mutes the AVR
and shuts off its front-panel display, but allows the AVR to automatically turn on and play audio in response to an AirPlay signal from a networked device. See Listening to Media via AirPlay, on page 22, for more information. When the AVR is in Standby, pressing the Power button turns it on. To put the AVR into Standby when it is on, press the Power button for less than three seconds. NOTE: The AVR will automatically
enter the Standby mode whenever no control buttons have been pressed and no audio signal has been present for 30 minutes.
On (Power indicator glows solid white): When the AVR is on it is fully operational.
IMPORTANT NOTE: If the PROTECT message ever appears on the AVR’s front­panel Message display, turn off the AVR and unplug it from the AC outlet. Check all speaker wires for a possible short circuit (the “+” and “–” conductors touching each other or both touching the same piece of metal). If a short circuit is not found, bring the unit to an authorized Harman Kardon service center for inspection and repair before using it again.
Tuning Mode button (AVR 1700 only): This button toggles between manual (one
frequency step at a time) and automatic (seeks frequencies with acceptable signal strength) tuning mode. It also toggles between stereo and mono modes when an FM station is tuned in.
RDS button (AVR 170 only): When listening to an FM radio station that broadcasts RDS information, this button activates the various RDS functions. NOTE: RDS service may not be available in all areas.
Channel Level Control button: Press this button to activate the channel-level adjustment feature. After pressing this button, use the Up/Down buttons to select the channel for adjustment and use the Left/Right buttons to adjust the channel’s level.
Digital Input button: Press this button to change the audio input for the current source. Use the Left/Right buttons to cycle through the available input connections, and press the Set button to assign the currently-displayed connection to the source.
IR sensor: This sensor receives infrared (IR) commands from the remote control. It is important to ensure that the sensor is not blocked.
Set button: Press this button to select the currently highlighted menu item. Left/Right buttons: Use these buttons to navigate the AVR’s menus. Message display: Various messages appear in this two-line display in response to
commands and changes in the incoming signal. In normal operation, the current source name appears on the upper line, while the surround mode is displayed on the lower line. When the on-screen display menu system (OSD) is in use, the current menu settings appear.
Up/Down buttons/Tuning buttons: Use these buttons to navigate the AVR’s menus. When the radio is the active source, use these buttons to tune stations according to the setting of the Tuning Mode button (see above).
Surround-Mode Category button: Press this button to select a surround-sound category. Each press changes the surround-mode category: Auto Select, Virtual, Stereo, Movie, Music and Video Game. To change the specific surround-sound mode within the category, use the Surround Mode Select buttons. See Audio Processing and Surround Sound, on page 23, for more information on surround modes.
Surround-Mode Select buttons: After you have selected the desired surround-mode category, press these buttons to select a specific mode within the category, such as to change from Dolby availability depends on the nature of the source input signal, i.e., digital versus analog, and the number of channels encoded within the signal.
Source Select buttons: Press these buttons to select the active source. Headphone jack/EzSet/EQ Mic connector: Connect a 1/4" stereo headphone plug to
this jack for private listening. This jack is also used to connect the supplied microphone for the EzSet/EQ procedure described in Configure the AVR for Your Speakers, on page 17.
USB port: The USB port can be used to play audio files from an Apple iOS connected to the port, and can also be used to play MP3 and WMA audio files from a USB device inserted into the port. Insert the connector or device into the USB port oriented so it fits all the way into the port. You may insert or remove the connector or device at any time - there is no installation or ejection procedure.
You can also use the USB port to perform firmware upgrades. If an upgrade for the AVR’s operating system is released in the future, you will be able to download it to the AVR using this port. Complete instructions will be provided at that time.
IMPORTANT: Do not connect a PC or other USB host/controller to this port, or you may damage both the AVR and the other device. HDD is not supported.
Volume knob: Turn this knob to raise or lower the volume. Aux Analog Audio Input connector: Connect an auxiliary source component that will be
used only temporarily, such as a camcorder, portable music player or game console, here.
®
Pro Logic® II Movie mode to Logic 7® Movie mode. Surround-mode
®
device
5
AVR
Rear-Panel Connectors
Rear-Panel Connectors
Radio Antenna
Connectors
Network
Connector
HDMI Input Connectors
HDMI Monitor Out
Connector
Digital Audio Input Connectors
RS-232 Connector
Analog Audio
Input/Output
Connectors
Subwoofer
Connector
IR In &
Trigger Out
Connectors
Speaker
Connectors
Composite Video Input Connectors
Composite Video Monitor Output Connectors
Main Power
Switch
AC Input
Connector
6
AVR
Rear-Panel Connectors, continued
English
Rear-Panel Connectors, continued
Radio Antenna connectors: Connect the included AM and FM antennas to their
respective terminals for radio reception. Analog Audio Input/Output connectors: Use the AVR’s Analog Audio Input/Output
connectors for source devices that don’t have HDMI or digital audio connectors. Use the Rec Out connectors to connect to the audio inputs of a VCR or tape deck. See Connect Your Audio and Video Source Devices, on page 13, for more information.
Network connector: Use a Cat. 5 or Cat. 5E cable (not supplied) to connect the AVR’s Network connector to your home network to enjoy Internet radio and content from DLNA­compatible devices that are joined to the network. See Connect to Your Home Network, on page 15, for more information.
Subwoofer connector: Connect this jack to a powered subwoofer with a line-level input. See Connect Your Subwoofer, on page 13, for more information.
IR In and Trigger Out connectors: When the IR sensor on the front panel is blocked (such as when the AVR is installed inside a cabinet), connect an optional IR receiver to the IR In jack. The Trigger Out connector provides 12V DC whenever the AVR is on. Connect it to the trigger input of a device such as a powered subwoofer.
Speaker connectors: Use two-conductor speaker wire to connect each set of terminals to the correct speaker. See Connect Your Speakers, on page 13, for more information.
®
HDMI
Input connectors: The HDMI (High-Definition Multimedia Interface) feature is
a connection for transmitting digital audio and video signals between devices. If your source devices have HDMI connectors, using them will provide the best possible video and audio performance quality. Since the HDMI cable carries both digital video and digital audio signals, you do not have to make any additional audio connections for devices you connect via HDMI connections. See Connect Your Audio and Video Source Devices, on page 13, for more information.
HDMI Monitor Out connector: If your TV has an HDMI connector and you have HDMI source devices, use an HDMI cable (not included) to connect it to the AVR’s HDMI Monitor Out connector.
Notes on using the HDMI Monitor Out connector:
• When connecting a DVI-equipped display to the HDMI Monitor Out connector, use
an HDMI-to-DVI adapter and make a separate audio connection.
• Make sure the HDMI-equipped display is HDCP-compliant. If it isn’t, do not connect
it via HDMI; use a composite analog video connection instead and make a separate audio connection.
Composite Video Input connectors: Use composite video connectors for video source devices that don’t have HDMI or component video connectors. You will also need to make an audio connection from the source device to the AVR. See Connect Your Audio and Video Source Devices, on page 13, for more information.
Composite Video Monitor Output connector: If your TV or video display does not have an HDMI connector, or if your TV does have an HDMI connector but you are connecting some source devices with only composite video connectors, use a composite video cable (not included) to connect the AVR’s Composite Video Monitor Out connector to your TV’s composite video input connector.
Digital Audio Input connectors: If your non-HDMI source devices have digital outputs, connect them to the AVR’s digital audio connectors. NOTE: Make only one type of digital connection (HDMI, optical or coaxial) from each device. See Connect Your Audio and Video Source Devices, on page 13, for more information.
RS-232 connector: This connector is used to connect to external control hardware. Consult a certified professional installer for more information.
Main Power switch: This mechanical switch turns the AVR’s power supply on or off. It is usually left on and cannot be turned on or off using the remote control.
AC Input connector: After you have made all other connections, plug the supplied AC power cord into this receptacle and into an unswitched wall outlet.
7
AVR
System Remote Control Functions
IR Transmitter Lens
Program Indicator LED
System Remote Control Functions
Power On Button Power Off Button
AVR Button
Test Tone Button
Channel Up/Down Buttons
Tone Controls Button
Back Button
OSD Button
Direct Station Entry Button
Memory Button
Mute Button
Source Selector Buttons
Channel Volume Adjust Button
Volume Up/Down Buttons
Delay Adjust Button
Options Button
OK Button
Sleep Button
Left/Right/Up/Down Buttons
Number Buttons
Clear Button Tuning Mode Button
Tuning Up/Down Buttons
Night Mode Button
Track Skip Up/Down Buttons
8
Preset Station Up/Down Buttons
Disc Skip Button (AVR 1700) RDS Button (AVR 170)
Macro Buttons
Display Dimmer Button
Transport Control Buttons
AVR
System Remote Control Functions, continued
English
System Remote Control Functions, continued
In addition to controlling the AVR, the AVR remote is capable of controlling five other devices, plus your TV and an iPod/iPhone that is docked in the AVR’s front-panel USB port. During the installation process, you may program the codes for each of your source components into the remote. (See Program the Remote to Control Your Source Devices and TV, on page 16, for programming information.) To operate a component, press its Source Selector button to change the remote’s control mode.
A button’s function depends on which component is being controlled. See Table A9 in the Appendix for listings of the functions for each type of component. Most of the buttons on the remote have dedicated functions, although the precise codes transmitted vary depending on the specific device being controlled. Due to the wide variety of functions for various source devices, we have included only a few of the most often-used functions on the remote: alphanumeric keys, transport controls, television-channel control, menu access and power on and off. To return the remote to the AVR control mode at any time, press the AVR button.
IR Transmitter lens: As buttons are pressed on the remote, infrared codes are emitted through this lens.
Program Indicator LED: This LED lights up to indicate various procedures when the remote is in the Programming mode.
Power On/Off buttons: Press these buttons to turn the AVR or the device being controlled on and off. The Main Power switch on the AVR’s rear panel must be on for this button to turn the AVR on and off.
NOTE: When the AVR is on, pressing the Power Off button for more than three seconds will put it into the Eco Standby mode. See Power indicator/Power button, on page 5 for more information.
Mute button: Press this button to mute the AVR’s speaker-output connectors and
Headphone jack. To restore the sound, press this button or adjust the volume.
AVR button: Press this button to switch the remote’s control mode to operate the AVR. Source Selector buttons: Press one of these buttons to select a source device, e.g.,
cable/satellite tuner, radio, etc. This action will also turn on the AVR and switch the remote’s control mode to operate the selected source device.
• The rst press of the Radio Source Selector button switches the AVR to the last-used
tuner band (AM or FM). Each successive press changes the band.
• The rst press of the USB button switches the AVR to the last-used source (USB or
iPod). Each successive press cycles between the two sourcee.
• The rst press of the Network button switches the AVR to the last-used source (Network
or vTuner). Each successive press cycles between the two sources.
Test Tone button: Press this button to activate the test tone for calibrating channel volume levels by ear.
Channel Volume Adjust button: Press this button to activate the individual channel­level adjustment. It lets you easily change the channel balance to suit different programs or seating arrangements. See Manual Speaker Setup, on page 24, for more information.
Channel Up/Down buttons: The Channel Up/Down buttons have no effect on the AVR but are used to change channels on TVs and some video sources.
Volume Up/Down buttons: Press these buttons to raise or lower the volume. Tone Controls button: Press this button to access the bass and treble controls. Use the
OK button to select an adjustment and use the Up/Down buttons to change the settings. Delay Adjust button: Pressing this button lets you adjust two different types of delay
settings (use the Up/Down buttons to cycle through the settings):
• A/V Sync: This setting lets you resynchronize the audio and video signals from a source
to eliminate a “lip sync” problem. Lip-sync issues can occur when the video portion of a signal undergoes additional processing in either the source device or the video display. Use the Left/Right buttons to delay the audio by up to 180ms.
• Front L/Center/Front R/Surr R/Surr L/Subwoofer: These settings let you set the delay for
each speaker to compensate for the different distances they may be from the listening position. Use the Up/Down buttons to cycle through each of the system’s speakers, and use the Left/Right buttons to set the distance each speaker is from the listening position. See Manual Speaker Setup, on page 24, for more information.
Back button: Press this button to return to the previous menu screen when you’re using the on-screen menu (OSD) system.
Options button: This button allows you to adjust playback and various other options for the AVR’s built-in sources and when controlling other components.
OSD button: Press this button to activate the on-screen display menu system. OK button: This button is used to select items from the menu system. Sleep button: Press this button to activate the sleep timer, which turns off the AVR after
a programmed period of time (up to 90 minutes).
Left/Right/Up/Down buttons: These buttons are used to navigate the menu system. Number buttons: Use these buttons to enter numbers for radio-station frequencies or
to select station presets. Direct Station Entry button: Press this button before using the Number buttons to enter
a radio station frequency. Clear button: Press this button to clear a radio station frequency you have started to
enter. Memory button: To save the currently tuned radio station as a preset, press this button,
then a Number button. Tuning Mode button: Press this button to toggle the radio between manual (one
frequency step at a time) and automatic (seeks frequencies with acceptable signal strength) tuning mode. It also toggles between stereo and mono modes when an FM station is tuned in.
Tuning Up/Down buttons: Press these buttons to tune a radio station. Depending on whether the tuning mode has been set to manual or automatic, each press will either change one tuning frequency increment at a time or seek the next higher or lower station with acceptable signal strength.
Preset Station Up/Down buttons: Press these buttons to cycle through your preset radio stations.
Night Mode button: Press this button to activate Night mode with specially encoded Dolby Digital discs or broadcasts. Night mode compresses the audio so that louder passages are reduced in volume to avoid disturbing others, while dialogue remains intelligible. Each press of the button advances through the following settings:
• Off: No compression is applied. Loud passages in the program remain as they were
recorded.
• Mid: Loud passages in the program are reduced moderately in volume.
• Max: Loud passages in the program are reduced more in volume.
Disc Skip button (AVR 1700): This button is used with some optical disc changers to skip to the next disc.
RDS button (AVR 170): When listening to an FM radio station that broadcasts RDS information, this button activates the various RDS functions.
Macro buttons: These buttons may be programmed to execute a series of up to 19 commands with a single button press. They are useful for programming the command
to turn on or off all of your components or for accessing specialized functions for a
different component from the one that you are currently operating. See Programming Macro Commands, on page 27, for information about programming macros.
Track Skip Up/Down buttons: These buttons are used with the AVR’s built-in sources (USB, iPod, Network, AirPlay, etc) and many source components to change tracks or chapters.
Display Dimmer button: Press this button to dim the AVR’s front-panel display partially or fully.
Transport Control buttons: These buttons have no effect on the AVR but are used to control many source components. By default, when the remote is operating the AVR, these buttons will control a Harman Kardon Blu-ray Disc
player or DVD player.
9
AVR
Introduction to Home Theater
and Place Your Speakers
Introduction to Home Theater
This introductory section will help you to familiarize yourself with some basic concepts
unique to multichannel surround-sound AVRs, which will make it easier for you to set up and operate your AVR.
Typical Home Theater System
A home theater typically includes an audio/video receiver (AVR), which controls the system and supplies amplification for the loudspeakers; a disc player; a source component for television broadcasts (cable box, satellite dish AVR, HDTV tuner or antenna connected to the TV); a TV or video display; and multiple loudspeakers.
Multichannel Audio
The main benefit of a home theater system is its ability to produce “surround sound.” Surround sound uses multiple speakers and amplifier channels to immerse you in the audio/video presentation for a dramatically increased sense of realism.
Your AVR can have up to five main speakers connected directly to it, plus a subwoofer. Each main speaker is powered by its own amplifier channel inside the AVR. A system with more than two speakers is called a multichannel system. The different main speaker types in a home theater system are:
• Front Left and Right: The front left and right speakers are used as in a 2-channel system. In many surround-sound modes, these speakers are secondary, while the main action, especially dialogue, is reproduced by the center speaker.
• Center: When you are watching movies and television programs, the center speaker reproduces most of the dialogue and other soundtrack information that occurs on the screen, anchoring it with the picture. When you are listening to a musical program, the center speaker helps to create a seamless front soundstage, creating a more realistic “you-are-there” listening experience.
• Surround Left and Right: The surround left and right speakers produce ambient sounds that help create a realistic and immersive surround-sound environment. They als o help recreate directional sound effects such as aircraft flyovers.
Many people expect the surround speakers to play as loudly as the front speakers. Although you will calibrate all of the speakers in your system to sound equally loud at the listening position, most artists use the surround speakers for ambient effects only, and they create their programs to steer relatively little sound to these speakers.
• Subwoofer: A subwoofer is designed to play only the lowest frequencies (the deep bass). It augments smaller, limited-range main speakers that are usually used for the other channels. Many digital-format programs, such as movies recorded in Dolby Digital, contain a low-frequency effects (LFE) channel that is directed to the subwoofer. The LFE channel packs the punch of a rumbling train or airplane, or the power of an explosion, adding realism and excitement to your home theater. Some people use two subwoofers for additional power and for even distribution of the sound.
Surround Modes
There are different theories as to the best way to present surround sound and to distribute the individual channel information to the surround-sound system’s speakers. A variety of algorithms have been developed in an effort to recreate the way we hear sounds in the real world, resulting in a rich variety of options. Several companies have developed different surround-sound technologies, all of which can be accurately reproduced by your AVR:
• Dolby Laboratories: Dolby TrueHD, Dolby Digital Plus, Dolby Digital, Dolby Digital EX, Dolby Pro Logic II.
• DTS: DTS-HD DTS NEO: 6™.
• HARMAN International: Logic 7, virtual speaker.
• Stereo Modes: 2-channel stereo and 5-channel stereo.
Appendix Table A8, on page 32, contains detailed explanations of the different surround­sound options available on your AVR. Digital surround-sound modes, such as Dolby Digital and DTS systems, are available only with specially encoded programs, such as those available via HDTV, DVD and Blu-ray Disc media and digital cable or satellite television. Other surround modes may be used with digital and analog signals to create a different surround presentation or to use a different number of speakers. Surround-mode selection depends upon the number of speakers in your system, the programs you are watching or listening to, and your personal tastes.
10
High Resolution Audio, DTS-HD Master Audio™, DTS, DTS 96/24™
Place Your Speakers
Determine the locations for your system’s speakers according to their manufacturer’s directions and the layout of your listening room. Use the illustration below as a guide for
5.1-channel systems. To create the most realistic surround-sound environment possible, you should place
your speakers in a circle with the listening position at its center. You should angle each speaker so it directly faces the listening position. Use the diagram below as a guide.
TV
C
FL FR
SL SR
Placing the Left, Center and Right Speakers
Place the center speaker either on top of, below or mounted on the wall above or below the TV or video-display screen. Place the front left and right speakers along the circle, about 30 degrees from the center speaker and angled toward the listener.
Place the front left, front right and center speakers at the same height, preferably at about the same height as the listener’s ears. The center speaker should be no more than 2 feet (0.6m) above or below the left/right speakers. If you’re using only two speakers with your AVR, place them in the front left and front right positions.
Placing the Surround Speakers
You should place the left and right surround speakers approximately 110 degrees from the center speaker, slightly behind and angled toward the listener. Alternatively, you can place them behind the listener, with each surround speaker facing the opposite-side front speaker. You should place the surround speakers 2 feet – 6 feet (0.6m – 1.8m) higher than the listener’s ears.
NOTE: Your AVR will sound its best when the same model or brand of loudspeaker is used for all positions.
Placing the Subwoofer
Because a room’s shape and volume can have a dramatic effect on a subwoofer’s performance, it is best to experiment with placement so that you will find the location that produces the best results in your particular listening room. With that in mind, these rules will help you get started:
• Placing the subwoofer next to a wall generally will increase the amount of bass in the
room.
• Placing the subwoofer in a corner generally will maximize the amount of bass in the
room.
• In many rooms, placing the subwoofer along the same plane as the left and right
speakers can produce the best integration between the sound of the subwoofer and that of the left and right speakers.
• In some rooms, the best performance could even result from placing the subwoofer
behind the listening position.
A good way to determine the best location for the subwoofer is by temporarily placing it in the listening position and playing music with strong bass content. Move around to various locations in the room while the system is playing (putting your ears where the subwoofer would be placed), and listen until you find the location where the bass performance is best. Place the subwoofer in that location.
SUB
AVR
Types of Home Theater
System Connections
English
Types of Home Theater System Connections
There are different types of audio and video connections used to connect the AVR to your speakers, your TV or video display, and your source devices. The Consumer Electronics Association has established the CEA® color-coding standard.
Connection Color Guide Table
Analog Audio Connection Color
Front Left/Right White/Red Center Green Surround Left/Right Blue/Gray Subwoofer Purple
Digital Audio Connection Color
Coaxial Orange Optical Black
Analog Video Connection Color
Composite Video Yellow
Speaker Connections
Speaker cables carry an amplified signal from the AVR’s speaker terminals to each loudspeaker. Each cable contains two wire conductors, or leads, that are differentiated in some way, such as with colors or stripes.
The differentiation helps you maintain proper polarity, without which your system’s low­frequency performance can suffer. Each speaker is connected to the AVR’s speaker­output terminals using two wires, one positive (+) and one negative (–). Always connect the positive terminal on the speaker, which is usually colored red, to the positive terminal on the AVR, which is colored as indicated in the Connection Color Guide Table, above. The negative terminals on the speakers and the AVR are black.
Your AVR uses binding-post speaker terminals that can accept bare-wire cables or banana plugs. Bare-wire cables are installed as shown below:
1. Unscrew Cap 3. Tighten Cap2. Insert Bare Wire
Banana plugs are inserted into the hole in the middle of the terminal cap, as shown below:
Subwoofer Connections
The subwoofer is a speaker dedicated to reproducing only the low (bass) frequencies, which require more power. To obtain the best results, most speaker manufacturers offer powered subwoofers that contain their own amplifiers. Use a single RCA audio cable (not included) to make a line-level (non-amplified) connection from the AVR’s Subwoofer connector to a corresponding input jack on the subwoofer.
Although the AVR’s purple subwoofer output looks similar to a full-range analog audio jack, it is filtered so that only the low frequencies pass through it. Don’t connect this output to any device other than a subwoofer.
Source Device Connections
Audio and video signals originate in source devices (components where a playback signal originates) such as your Blu-ray Disc or DVD player, CD player, DVR (digital video recorder) or other recorder, tape deck, game console, cable or satellite television tuner, or a device docked in the AVR’s USB port. The AVR’s FM/AM tuner also counts as a source, even though no external connectors are needed other than the AVR’s FM and AM antennas. Separate connectors are required for the audio and video portions of the source device’s signal, except for digital HDMI connectors. The types of connectors you use will depend upon the capabilities of the source device and of your TV or video display.
Digital Audio Connections – HDMI
There are two types of audio connections – digital and analog. Digital audio signals are required for listening to sources encoded with digital surround modes, such as Dolby Digital and DTS, or for uncompressed PCM digital audio. Your AVR has three types of digital audio connectors: HDMI, coaxial and optical. Do not use more than one type of digital audio connector for each source device. However, it’s okay to make both analog and digital audio connections to the same source.
Your AVR is equipped with four rear-panel HDMI input connectors and one HDMI monitor output connector. HDMI technology enables digital audio and video information to be carried using a single cable, delivering the highest quality picture and sound. If your TV or video-display device has an HDMI input connector, make a single HDMI connection from each source device to the AVR.
The AVR’s HDMI Monitor Output connector contains an Audio Return Channel (ARC) that carries a digital audio signal from your TV or video display back to the AVR. It allows you to listen to HDMI devices that are connected directly to your TV (such as an Internet connection) without making an additional connection from the device to the AVR. The ARC signal is active when the TV source is selected. See System Setup, on page 26, for more information.
The HDMI connector is shaped for easy plug-in (see illustration, below), and HDMI cable runs are limited to about 10 feet (3m). If your video display has a DVI input and is HDCP-compliant, use an HDMI-to-DVI adapter (not included), and make a separate audio connection.
A. Tighten Cap B. Insert Banana Connector
into Hole in Cap
Always connect the colored (+) terminal on the AVR to the (+) terminal on the speaker (usually red), and the black (–) terminal on the AVR to the (–) terminal on the speaker (usually black).
IMPORTANT: Make sure the ( + ) and ( – ) bare wires do not touch each other or the other terminal. Touching wires can cause a short circuit that can damage your AVR or amplifier.
Digital Audio Connections – Coaxial
Coaxial digital audio jacks are usually color-coded orange. Although they look like standard RCA-type analog jacks, you should not connect coaxial digital audio outputs to analog inputs or vice versa.
11
AVR
Types of Home Theater System
Connections, continued
Digital Audio Connections – Optical
Optical digital audio connectors are normally covered by a shutter to protect them from dust. The shutter opens as the cable is inserted. Optical input connectors are color-coded using a black shutter.
Analog Audio Connections
Two-channel analog connections require a stereo audio cable, with one connector for the left channel (white) and one for the right channel (red). These two connectors are attached to each other.
For source devices that have both digital and analog audio outputs, you may make both connections.
Video Connections
Many source devices output both audio and video signals (e.g., Blu-ray Disc, DVD player, cable television box, HDTV tuner, satellite box, VCR, DVR). In addition to an audio connection as described above, make a video connection for each of these source devices. Make only one type of video connection for each device.
Digital Video Connections
If you have already connected a source device to one of the AVR’s HDMI input connectors, you have automatically made a video connection for that device, since the HDMI cable carries both digital audio and digital video signals.
Analog Video Connections – Composite Video
Composite video is the basic connection most commonly available. Both the chrominance (color) and the luminance (intensity) components of the video signal are transmitted using a single cable. The jack is usually color-coded yellow and looks like an analog audio jack. Do not connect a composite video jack to an analog audio or coaxial digital audio jack, or vice versa.
USB Port
The AVR can play audio files from an Apple iOS® device connected to the USB port, and allows you to control the iOS device via the AVR remote control. The AVR can also play MP3 and WMA audio files from a USB device inserted into the USB port. Insert the connector or device into the USB port oriented so it fits all the way into the port. You may insert or remove the connector or device at any time – there is no installation or ejection procedure.
The USB port on your AVR is also used to perform firmware upgrades. If an upgrade for the AVR’s operating system is released in the future, you will be able to download it to the AVR using this port. Complete instructions will be provided at that time.
IMPORTANT: Do not connect a PC or other USB host/controller to the AVR’s USB port, or you may damage both the AVR and the other device. HDD is not supported.
Radio Connections
Your AVR uses separate terminals for the included FM and AM antennas. The FM antenna uses a 75-ohm F-connector.
The AM antenna connector uses spring-clip terminals. After assembling the antenna as shown below, press the levers to open the connectors, insert the bare wires into the
openings, and release the levers to secure the wires. The antenna wires are not polarized,
so you can insert either wire into either connector.
12
AVR
Making Connections
English
Making Connections
CAUTION: Before making any connections to the AVR, ensure that the AVR’s AC cord is unplugged from the AVR and the AC outlet. Making connections with the AVR plugged in and turned on could damage the speakers.
Connect Your Speakers
After you have placed your loudspeakers in the room as explained in Place Your Speakers, on page 10, connect each speaker to its color-coded terminal on the AVR as explained in Speaker Connections, on page 11. Connect the speakers as shown in the illustration.
C
FL
SL
Connect Your Subwoofer
Use a single RCA audio cable to connect the AVR’s Subwoofer Pre-Out connector to your subwoofer. Consult your subwoofer’s user manual for specific information about making connections to it.
Receiver
Subwoofer
Connector
Single RCA Audio Cable (not supplied)
FR
SR
Powered
Subwoofer
Connect Your TV or Video Display
HDMI Monitor Out connector
If your TV has an HDMI connector and you have HDMI or component video source devices, use an HDMI cable (not included) to connect your TV to the AVR’s HDMI Monitor Out connector. It will provide the best possible picture quality.
AVR HDMI
Monitor Out
Connector
HDMI Cable
(not supplied)
Composite Video Monitor Out connector
If your TV does not have an HDMI connector, or if your TV does have an HDMI connector but you are connecting some source devices with only composite video connectors, use a composite video cable (not included) to connect the AVR’s Composite Monitor Out connector to your TV’s composite video connector.
AVR Composite
Monitor Out
Connector
Composite Video Cable
(not supplied)
TV
TV
Connect Your Audio and Video Source Devices
Source devices are components where a playback signal originates, e.g. a Blu-ray Disc or DVD player; a cable, satellite or HDTV tuner; etc. Your AVR has several different types of input connectors for your audio and video source devices: HDMI, composite video, optical digital audio, coaxial digital audio and analog audio.
Your AVR’s various Source Selector buttons have default assignments to different input connectors (listed in the “Default AVR Input Connector” column of the table below). For ease of setup and remote control programming, you should connect each source device to the connector where the corresponding default source button is assigned (e.g., connect your Cable/Satellite tuner box to HDMI 1).
However, you can connect your source devices as you wish and re-assign any of the video and audio input connectors to any of the Source Selector buttons listed in the table according to where you actually connect each of your source devices.
As you connect your various source components, fill out the “Connected Device” and “Assigned AVR Input Connector(s)” columns in the table – it will make it easier for you to assign the connectors to the Source Selector buttons after you have completed making all of the connections. (You will make any changes to the connector assignments later in the setup process.)
Source Selector
Button
Cable/Sat HDMI 1 TV HDMI ARC
Disc HDMI 2
Server HDMI 3 Aux COMP. VID. 1/AUX AUDIO Game HDMI 5 STB HDMI 6 Audio ANALOG AUDIO 2 Network NETWORK Home Network –––– ––––
Input Connections and Source Buttons
Default AVR Input
Connector
Connected
Device
Assigned AVR Input
Connector(s)
Video Audio
13
AVR
Making Connections, continued
HDMI devices
If any of your source devices have HDMI connectors, using those connectors will provide the best possible video and audio performance quality. Since the HDMI cable carries both digital video and digital audio signals, you do not have to make any additional audio connections for devices you connect via HDMI cables.
If you have a TV or other source device equipped with the HDMI Audio Return Channel function, you can feed its sound to the AVR via the HDMI Monitor Out connector’s Audio Return Channel, and it will not require additional audio connections to the AVR.
AVR
HDMI Connectors
HDMI Cable (not supplied)
To HDMI Output
HDMI-Equipped Source Device
Composite video devices
Use composite video connectors for video source devices that don’t have HDMI connectors. You will also need to make an audio connection from the source device to the AVR.
AVR Component
Video Connectors
Optical digital audio devices
If your non-HDMI source devices have optical digital outputs, connect them to the AVR’s Optical Digital Audio connectors. NOTE: Make only one type of digital connection (HDMI, optical or coaxial) from each device.
NOTE: Be sure to remove the caps from the tips of the optical cable before inserting them into the AVR and your source device.
AVR Digital Audio
Connectors
Coaxial digital audio devices
If your non-HDMI source devices have coaxial digital outputs, connect them to the AVR’s Coaxial Digital Audio connectors.
NOTE: Make only one type of digital connection (HDMI, optical or coaxial) from each device.
AVR Digital Audio
Connectors
Remove Caps
Optical Digital Audio Cable (not supplied)
Optical-Equipped Source Device
To Optical Digital Audio Output
Composite Video Cable (not supplied)
Composite Video-Equipped
Source Device
To Composite Video Output
Coaxial Digital Audio
Cable (not supplied)
To Coaxial Digital Audio Output
Coaxial-Equipped Source Device
Analog audio devices
Make analog audio connections from your source devices that do not have HDMI or digital audio connectors.
AVR Analog Audio
Connectors
Stereo Audio Cable (not supplied)
To Stereo Analog Audio Output
14
Analog Source Device
AVR
Making Connections, continued
English
Audio recorders
Connect an analog audio recorder’s inputs to the AVR’s analog audio Rec Out connectors. The recorded signal is determined by the source’s Record Out setting in the Source Setup menu. See Additional Source Setup Menu Items, on page 19, for more information.
AVR Analog Audio
Recorder Connectors
Stereo Audio Cable (not supplied)
To Stereo Analog Record Inputs
Analog Recording Device
Video recorders
Connect an analog video recorder’s video input connector to the AVR’s Composite Monitor Out connector. You can record any composite video signal. To record the audio and video from the source device, connect the AVR’s Analog Rec Out connectors to the analog video recorder’s audio inputs.
NOTE: If you have connected the AVR’s Composite Monitor Out video connector to your TV, you cannot connect a VCR to the AVR for recording.
AVR Analog
Audio Recorder
Connectors
AVR Analog
Video Recorder
Connectors
Connect the Radio Antennas
• Connect the supplied FM antenna to the AVR’s FM 75Ω Radio Antenna connector. For the best reception, extend the FM antenna as far as possible.
• Bend and fold the base of the supplied AM antenna as shown and connect the antenna
wires to the AVR’s AM and Gnd connectors. Rotate the antenna as necessary to
minimize background noise.
AVR
Antenna
Connectors
AM Antenna
(supplied)
FM Antenna (supplied)
Bend and fold base
Connect IR Equipment
If you place the AVR inside a cabinet or facing away from the listener so that the AVR’s IR sensor is not within line-of-sight of the remote control, connect an external IR receiver, such as the Harman Kardon HE 1000 (available separately) to the AVR’s IR In connector.
External IR
AVR IR Remote
In Connector
IR IN
Receiver
AVR and Source Devices Installed Inside of Cabinet
Analog Audio/Video Cable (not supplied)
To Analog Audio/Video
Record Inputs
Analog Video Recording Device
Connect to Your Home Network
Use a Cat. 5 or Cat. 5E cable (not supplied) to connect the AVR’s Network connector to your home network to enjoy Internet radio and content from DLNA®-compatible devices that are connected to the network.
AVR
Network
Connector
Cat. 5/5E Cable
(not supplied)
Network
Modem
To
Home
Network
and
Internet
Connect the Trigger Output
If your system has equipment that can be controlled by a DC trigger signal, connect it to the AVR’s Trigger Out connector with a mono 1/8-inch (3.5mm) mini-plug interconnect cable. The AVR will supply a 12V DC (100mA) trigger signal at this connection whenever it is powered on.
AVR
Mono 1/8-inch (3.5mm)
Device with Trigger
in Connector
Mini-Plug Interconnect (not supplied)
15
AVR
Making Connections, continued,
and Set Up the Remote Control
Connect to AC Power
Connect the AC power cord to the AVR’s AC Input connector and then to a working AC power outlet.
AVR AC
Input Connector
AC Power
Outlet
Power Cord
(supplied)
Set Up the Remote Control
Install the Batteries in the Remote Control
Remove the remote control’s battery cover, insert the three supplied AAA batteries as shown in the illustration, and replace the battery cover.
NOTE: Remove the protective film from the AVR’s front panel to keep it from reducing the remote control’s effectiveness.
Program the Remote to Control Your Source Devices and TV
In addition to using the remote to control the AVR itself and the AM/FM radio, you can program the remote to control up to five additional audio/video source devices plus your TV via the Cable/Sat, Disc, Server, Game, STB and TV Source Selector buttons. The remote is also ready to operate your iPod or iPhone device when the device is connected to the AVR’s front-panel USB port.
Once you have programmed the remote, you can switch the remote’s control mode to access the functions for a particular source device by pressing the remote’s Source Selector button for that device. To control the AVR, press the remote’s AVR button.
Before you begin programming the remote, review the connections you filled in on the Input Connections and Source Buttons table on page 13. The Source Selector buttons are assigned to the components that you listed in the table’s “Connected Device” column.
Each of the programmable Source Selector buttons is set at the factory to control that specific type of device: the Cable/Sat button is set to control cable/satellite tuners, the Disc button is set to control DVD and Blu-ray Disc players, the Server button is set to control digital music servers, the Game button is set to control game consoles, the STB box is set to control DVRs and TiVo
You can program an unused Source Selector button to control a source device that is different from that button’s factory setting (such as programming the Server button to control a DVD player or a second TV), but completely different types of devices, such as CD players and VCRs, cannot be controlled at all. See Advanced Remote Control Programming, on page 26, for more information.
®
devices, and the TV button is set to control TVs.
1. Turn on the source device you want to program the remote to control.
2. Look up the code numbers for the device in Tables A10 – A17 in the Appendix. Write all the applicable code numbers in a convenient place.
3. Press and hold the Source Selector button for that source device until the Program Indicator LED on the remote starts to flash, then release it. (This procedure places the remote in the Programming mode.)
4. Aim the remote at the source device and use the remote’s Number buttons to enter a
code number from Step 2, above.
a) If the device turns off, press the Source Selector button again to save its code. The
Source Selector button will flash, and the remote will exit the Programming mode. b) If the device does not turn off, enter another code number. c) If you run out of code numbers for a device, you can search through all of the codes
in the remote’s library for devices of its type by pressing the Up or Down button repeatedly until the device turns off. When it does, press the Source Selector button to save the code.
5. Check that other functions control the device correctly. Sometimes manufacturers use the same Power code for several models, while other function codes vary. Repeat this process until you’ve programmed a satisfactory code set that operates most of the device’s functions.
6. If you searched through the remote’s code library to find the code, you can find out which code number you have programmed by pressing and holding the Source Selector button to re-enter the Programming Mode. Then press the remote’s OK button, and the Program Indicator LED will flash in the code sequence. One flash represents “1,” two flashes represent “2,” and so forth. A series of quick flashes represents “0.” Record the code number programmed for each device in Table A6 in the Appendix.
Repeat Steps 3 – 6 for each source device you want to control with the AVR remote. In general, the label for each button on the remote describes the button’s function when
used to control the AVR. However, the button may perform a very different function when used to control another device. Refer to the Remote Control Function List, Table A9 in the Appendix, for each button’s functions with the various product types.
You can also program the remote to perform macros (preprogrammed code sequences that execute many code commands with a single button press) and “punch-through” programming (allowing the remote to operate a device’s channel or transport controls when the remote is in another device’s mode). See Advanced Remote Control Programming, on page 26, for instructions on these functions.
16
AVR
Set Up the AVR
English
Set Up the AVR
Turn On the AVR
1. Set the rear-panel Main Power switch to “On.” (The front-panel Power indicator will glow amber.)
2. Press the front-panel Power button.
Main Power
Switch
Unless you will not be using the AVR for an extended period of time, leave the Main Power switch set to “On.” When the Main Power switch is turned off, any settings you have programmed will be preserved for up to four weeks.
IMPORTANT NOTE: If the PROTECT message ever appears in the Message display, turn off the AVR and unplug it. Check all speaker wires for a short circuit (“+” and “–” wires touching). If none is found, bring the unit to an authorized Harman Kardon service center for inspection and repair before using it again.
Using the On-Screen Menu System
Although it’s possible to configure the AVR using only the remote and the front-panel Message display, it is easier to use the on-screen menu system.
To access the menus, press the OSD button on the remote. The Master Menu will appear. (Note: If you have only used a composite video connection to your TV, the OSD menus will not appear on your TV. Follow the steps below using the receiver’s front-panel display.)
Power Button
Configure the AVR for Your Speakers
NOTE: If there are fewer than five main speakers in your system, do not use the EzSet/ EQ process. Instead, proceed as described in Manual Speaker Setup, on page 24.
1. Plug the supplied EzSet/EQ microphone into the AVR’s Headphone connector.
AVR
Headphone
Connector
EzSet/EQ Microphone
(supplied)
2. Place the microphone at ear height in your listening position. The microphone features a threaded insert on the bottom for mounting on a camera tripod.
3. Set the volume control on your subwoofer to approximately the halfway point.
4. Turn on your TV and select the TV input where you connected the AVR in Connect Your
TV or Video Display, on page 13.
5. Press the remote control’s OSD button. The AVR’s on-screen display (OSD) Master Menu will appear on the TV.
MASTER MENU
Source Select
Source Setup
Surround Mode
EzSet/EQ
Manual Setup
Network
System Setup
NOTE: The OSD screens shown in this manual may differ slightly from the actual screens.
MASTER MENU
Source Select
Source Setup
Surround Mode
EzSet/EQ
Manual Setup
Network
System Setup
The Master menu consists of seven submenus: Source Select, Source Setup, Surround
Mode, EzSet/EQ, Manual Setup, Network and System Setup.
Use the Up/Down/Left/Right buttons on the remote to navigate the menu system, and press the OK button to select a menu or setting line, or to enter a new setting.
The current menu, setting line or setting will appear in the front-panel Message display, as well as on screen.
To return to the previous menu, press the remote control’s Back button. Most users should follow the instructions in this Set Up the AVR section to configure
a basic home theater system. You may return to these menus at any time to make additional adjustments, such as those described in the Advanced Functions section, on pages 23 through 27.
Before you begin initial setup, all loudspeakers, a video display and all source devices should be connected to the AVR. You should be able to turn on the AVR and view the Master menu when you press the OSD button. If necessary, reread the Making Connections section and the beginning of this section before continuing.
6. Use the remote’s arrow and OK buttons to select “EzSet/EQ.”
EzSet/EQ
Place the microphone at the
listening position and plug it into
the Headphone Jack.
Do you want to start EzSet/EQ?
Yes
No
7. Select “YES.” The Speaker Configuration menu will appear.
EzSet/EQ
Speaker configuration.
5.1
Cancel
17
AVR
Set Up the AVR, continued
8. Select “5.1.”
9. The test will begin. Make sure that the room is quiet while the test noise is playing through the speakers.
10. When the test finishes, press the remote’s OSD button to exit.
Assign the AVR Input Connectors
1. Review the input connections you listed on the connection table, on page 13. Note what changes (if any) you have made from the default AVR Input Connector assignments that appear on the list. If you connected your so urce devices according to the entries in the “Default AVR Input Connector” column of the table on page 13, you can skip this section.
2. Turn on your TV and select the TV input where you connected the AVR in Connect Your TV or Video Display, on page 13.
3. Press the remote control’s OSD button. The AVR’s on-screen display (OSD) Master Menu will appear on the TV.
NOTE: If you have used a composite video connection to your TV, the OSD menus will not appear on your TV. Follow the steps below using the AVR’s front-panel display.
MASTER MENU
Source Select
Source Setup
Surround Mode
EzSet/EQ
Manual Setup
Network
System Setup
4. Use the remote’s arrow and OK buttons to select “Source Setup.” If there is a Source Selector for which you want to assign different video or audio connections. use the left/ right arrow buttons to select it, and press the OK button.
Source Setup
Source < Cable/Satellite >
Title
Video In HDMI 1
A udio In H DMI 1
T one Out
Bass 0
T reble 0
Night Mode Off
Record Out A nalog
6. Select “Audio In” and use the left/right arrow buttons to select the audio input connector you want to assign to the Source button.
NOTE: If you have assigned an HDMI Video connector for the Source button you cannot assign a different Audio connector.
Source Setup
Source < Cable/Satellite >
Title
Video In Composite 1
A udio In Optical 1
T one Out
Bass 0
T reble 0
Night Mode Off
Record Out A nalog
7. Repeat steps 4 – 6 for the remaining audio/video connections that you want to re­assign.
Set Up the Network
To play MP3 or WMA media located on DLNA-compatible devices connected to the network, to use the AVR’s internal Internet radio tuner (vTuner) to listen to audio streams or to stream audio to the AVR via AirPlay, connect the AVR’s Network connector to the Ethernet port on a router or modem that has Internet access, to a home network, or to a PC. (See Connect to Your Home Network, on page 15.)
We recommend that you connect the AVR directly to a home-network router so that it can directly access the Internet for Internet radio and access other devices on the network for playback of shared content (see Listening to Media on Your Home Network, on page 21, for more information).
If your network uses an automatic IP address, you should not have to perform any network setup procedures. Once you connect the AVR to your home network, the network should automatically assign the AVR an IP address, and the AVR should automatically connect to your network. If your AVR does not automatically connect to your network (in which case the AVR will display a “Not Connected” message when you press the Network source button):
1. Press the OSD button and select Network. The Network setup menu will appear.
Network
IP Configuration A uto
IP Address 000.000.000.000
Subnet Mast 255.000.000.000
Gateway 000.000.000.000
Primary DNS 000.000.000.000
Secondary DNS 0 00.000.000.000
Proxy Config Off
IP Address 000.000.000.000
Port 000
5. Select “Video In” and use the left/right arrow buttons to select the video input connector you want to assign to the Source Selector button. Press the OK button.
NOTE: If you select an HDMI connector for the Video connection the Audio connection will automatically change to the same HDMI connector.
Source Setup
Source < Cable/Satellite >
Title
Video In HDMI 2
A udio In H DMI 2
T one Out
Bass 0
T reble 0
Night Mode Off
Record Out A nalog
18
2. Select IP Configuration, then press the Left or Right button twice to cycle the setting from “Auto” to “Manual” and back to “Auto.”
3. Scroll to the bottom of the list and select “Apply & Save.” The AVR will enter the Standby mode. When you turn the AVR back on, it will attempt to connect to the network.
4. If the AVR again fails to connect to the network, you may need to enter your network’s settings manually. In this case, you must obtain these settings from your ISP or network administrator. After obtaining your network’s settings:
a) Select IP Address and use the Left or Right button to change the setting to “Manual.”
The following settings will become active: IP Address, Subnet Mask, Gateway, Primary DNS and Secondary DNS.
b) Use the Up/Down arrow buttons to select the correct numbers and make the entries
for all of these settings.
AVR
Operating Your AVR
English
c) When you have finished, select “Apply & Save,” and press the OK button. The AVR
will refresh the network connection while it remains on. If the AVR cannot connect to the network using the manual settings, contact your ISP or network administrator for assistance.
• Proxy Cong: If you have connected the AVR’s Network connection to a proxy network,
use the Left/Right buttons to set this to “On”, and use the number buttons to enter tne proxy network’s IP address and port.
• Network Status: This line indicates the AVR’s current network-connection status
(Connected/Not Connected/Network Problem).
• Apply & Save: Any time you make a change in any of the Network settings, the Apply &
Save line will become available. Select this line and press the OK button. The AVR will go into the Standby mode. After you turn the AVR back on, the new network settings will be in effect. IMPORTANT: You must select “Apply & Save” for your network
settings to take effect.
NOTE: If you have trouble connecting to the network at any time, cycle the AVR into the Standby mode, and then turn it back on.
Additional Source Setup Menu Items
You can also adjust the following settings independently for each source: Title: You may change the display name for any source (except the radio). This feature
may help you to select the correct source device even when you have forgotten which physical connections you used.
1. Move the cursor to the Title line and press the OK button. A block cursor will blink.
2. Use the Up/Down buttons to scroll through the alphabet in upper and lower case, the numbers and many punctuation marks. When you have selected the desired character, press the Right button to move to the next space. Press the Right button twice to leave a blank space.
3. Press the OK button when you have finished.
Tone: This setting determines whether the treble and bass controls are active. When this line is set to Out, the tone controls are out of the circuit, with no changes to the sound. When this line is set to In, the bass and treble frequencies are boosted or cut, depending upon the Bass and Treble settings (see below).
Bass and Treble: Boost or cut the low or high frequencies by up to 10dB by using the Left/Right buttons to change the setting by 2dB at a time.
Night Mode: This setting activates Night mode with specially encoded Dolby Digital discs or broadcasts. Night mode compresses the audio so that louder passages are reduced in volume to avoid disturbing others, while dialogue remains intelligible. Each press of the right arrow button advances through the following settings:
• Off: No compression is applied. Loud passages in the program remain as they were
recorded.
• Mid: Loud passages in the program are reduced moderately in volume.
• Max: Loud passages in the program are reduced more in volume.
Record Out: This setting determines the source of the signal that appears at the Analog Audio Rec Out connectors for the Cable/Sat, TV, Disc, Server, Aux, Game, STB and Audio sources:
• DSP Down mix: This setting outputs audio from digital audio input connections (HDMI,
optical, coaxial) and analog audio input connections (Analog 1/2, Aux).
• Analog: This setting outputs audio only from the analog audio input connections (Analog
1/2, Aux).
NOTE: Although the USB, FM/AM, AirPlay, DLNA, and Internet Radio sources do not have Record Out settings, they are also available for recording.
When you’re finished, press the remote’s OSD button to turn off the on-screen menu.
Operating Your AVR
Now that you have installed your components and completed a basic configuration, you are ready to begin enjoying your home theater system.
Controlling the Volume
Adjust the volume either by turning the front-panel Volume knob (clockwise to increase volume or counterclockwise to decrease volume) or by pressing the Volume Up/Down buttons on the remote. The volume is displayed as a negative number of decibels (dB) below the 0dB reference point.
0dB is the maximum recommended volume for your AVR. Although it’s possible to turn the volume to a higher level, doing so may damage your hearing and your speakers. For certain more dynamic audio materials, even 0dB may be too high, allowing for damage to equipment. Use caution with regard to volume levels.
Muting the Sound
To mute all speakers and the headphones, press the Mute button on the remote. Any recording in progress will not be affected. The MUTE message will appear in the front­panel display as a reminder. To restore the sound, press the Mute button again, or adjust the volume.
Listening Through Headphones
Plug the 1/4-inch stereo plug on a pair of headphones into the front-panel Phones jack for private listening. The default headphone surround mode for all sources except FM and AM is HARMAN Headphone, which will emulate a 5.1-channel speaker system. The default surround mode for FM and AM is 2-Ch Stereo. Press the Surround Mode button on the front panel or use the remote and OSD to switch between HARMAN Headphone and 2-Ch Stereo. No other surround modes are available for headphone listening.
Selecting a Source
There are three different ways to select a source:
• Press the front-panel Source Select buttons.
• Directly select any source by pressing its Source Selector button on the remote.
• Select a source from the Source Select menu in the OSD menu system.
The AVR selects the audio and video inputs you assigned to the source and any other settings you made during setup.
The source name and the surround mode will appear on the front panel.
Video Troubleshooting Tips
If there is no picture:
• Check the source selection.
• Check all connections for a loose or incorrect connection.
• Check the video-input selection on the TV/display device.
Additional Tips for Troubleshooting HDMI Connections
• Turn off all devices (including the TV, the AVR and any source components).
• Unplug the HDMI cables, starting with the cable between the AVR and the TV, and
continuing with the cables between the AVR and each source device.
• Carefully reconnect the cables from the source devices to the AVR. Connect the
cable from the AVR to the TV last.
• Turn on the devices in this order: TV, AVR, source devices.
NOTE: Depending upon the particular components involved, the complexity of the required communication between HDMI components may cause delays of up to a minute in the completion of some actions, such as input switching or switching between SD and HD channels.
19
AVR
Operating Your AVR, continued
Listening to FM and AM Radio
Select the Radio source. Use the Tuning Up/Down buttons to tune a station, which will be shown on the front-panel display and the TV screen.
The AVR defaults to automatic tuning, meaning each press of the Tuning Up/Down buttons scans until a station with acceptable signal strength is found. To switch to manual tuning, in which each press of a Tuning button steps through a single frequency increment, press the Tuning Mode button. Each press of the Tuning Mode button toggles between the automatic and manual tuning modes.
Once you have tuned an FM station, toggling the Tuning Mode setting also switches the radio between stereo and monaural reception. (Mono reception may improve reception of weaker stations.)
Preset Stations
A total of 30 stations (AM and FM combined) may be stored as presets. When the desired station has been tuned in, press the Memory button on the remote, and two dashes will flash on the front-panel Message display. Use the Number buttons to enter the desired preset number.
To tune a preset station, press the Preset Up/Down buttons or enter the preset number using the Number buttons.
Listening to Internet Radio (vTuner™)
Your AVR’s Network connection brings you a world of MP3- and WMA-format streams via the Internet. After you have successfully connected to your home network as described in Connect to Your Home Network, on page 15, and set up the network as described in Set Up the Network, on page 18, press the Network Source Selector button on the remote until Internet Radio appears on the AVR’s front-panel display. (Each press cycles between the Network and Internet Radio sources.)
vTuner
Favorite
Added Stations
Location
Genre
New Stations
P odcasts by Location
P odcasts by Genre
Search
With the vTuner screen (above) displayed, the AVR will automatically connect to the Internet via the www.radioharmankardon.com portal. To select a stream, use the Up/ Down buttons to select a category.
Favorites: To create a Favorites list:
1) Write down your AVR’s MAC Address number, which is found in the Network Setup menu. See Set Up the Network, on page 18, for more information.
2) Log onto www.radioharmankardon.com from your computer. Create an account using your AVR’s MAC address as its ID number.
Favorites that you select on the Web site will be available when you listen to vTuner on the AVR.
Listening to an iPod/iPhone/iPad Device
When a compatible iPod, iPhone or iPad is connected to the AVR’s USB port, you may play the audio materials on the device through your high-quality audio/video system, operate the iPod, iPhone or iPad using the AVR remote, view navigation messages on the AVR’s front panel or a connected video display and charge the connected device.
After connecting your iPod, iPhone or iPad to the AVR’s USB port, press the USB Source Selector button. (If “USB” appears as the source, press the button a second time to switch from the USB source to the iPod source.) The iPod menu screen will appear.
Music
Playlists
Artist
Albums
Songs
Genres
Composers
A udio Books
P odcasts
Use the Up/Down and OK buttons to navigate through the list and select the desired category. When the category’s screen appears, use the Up/Down and OK buttons to navigate within the category and make selections. NOTE: Not all categories may appear with all iPod/iPhone /iPad devices.
Once you select a song the iPod playback screen will appear on the OSD.
iPod
J ugalbandi
Previously Disenchanted
Y ellow Star Mailing List
3:21
NOTE: The categories displayed may vary by region.
Once you select a stream, the OSD will display the vTuner playback screen, which contains information about the currently playing song.
vTuner
J ugalbandi
The Madagascar W ombat
Laydown Delivery
2:12
20
The screen will show the currently playing song, artist, album, elapsed time and total track time. Use the remote’s Transport Control buttons to control playback.
• To return to a previous menu screen at any time, press the Back button.
Listening to Media on a USB Device
Your AVR is compatible with USB 2.0 or USB 1.1 media in the FAT 16 or FAT 32 file format and is compatible with the following MP3 and WMA media:
• MP3: Bit rates between 96kbps and 320kbps. Fixed bit-rates at 44.1kHz sampling is
recommended. Variable bit-rates (VBR) are playable, but playing time may be displayed incorrectly. Files must have an “.mp3” file extension.
• WMA: Bit rates of 64kbps or higher.
NOTE: Bit rates of 80kbps and 256kbps are not compatible. Files must have a “.wma” file extension.
A maximum number of 65,536 folders and files can be supported.
AVR
Operating Your AVR, continued
English
Playing files on a USB device
1. Insert the USB drive into the AVR’s front-panel USB port.
IMPORTANT: Do not connect a personal computer or peripheral to the USB port. USB hubs are not supported.
2. Select USB as the source device. (If “iPod” appears as the source, press the button a second time to switch from the iPod source to the USB source.) The USB screen will appear.
USB
Folder 1
Folder 2
Folder 3
Folder 4
3. Use the remote’s Up, Down and OK buttons to select a folder and display its contents.
4. Use the remote’s Up, Down and OK buttons to select a song. The song will play and the USB playback screen will appear on the OSD.
USB
J ugalbandi
The Lost T ransit Center
Night Crazy
9:17
To share media on PCs:
1. Open Windows Media Player.
2. Open the Library menu and select “Media Sharing.” The Media Sharing window will appear.
3. Check the “Share My Media” box. An icon for the AVR will appear in the window.
4. Select the AVR icon, select “Allow,” then select “OK.”
The computer’s WMA and MP3 media should now be available to the AVR. To share media on other types of computers, operating systems or media software, check
the instructions for the computer, operating system or media player.
To listen to shared media:
1. Press the Network Source Selector button. (If “Internet Radio” appears as the source, press the button a second time to switch from the Internet Radio source to the Network source.) The Network screen will appear.
Home Network
Server 1
Server 2
Server 3
The screen should list by name all devices on the network that allow sharing.
2. Use the remote’s Up, Down and OK buttons to select a device. The screen will display the device’s folder structure.
3. Use the Up and Down buttons to browse the content stored in the device’s media player library. Scroll to the desired item and press the OK button to select it. The song will play and the Network playback screen will appear on the OSD.
• Use the remote’s Transport Control buttons to control playback.
• To access Shufe and Repeat functions, press the remote’s Options button.
When the song is finished playing the remaining contents of the folder will play.
Listening to Media via Your Home Network
Your AVR can play MP3 and WMA audio media that is stored on a PC or Mac computer when both the computer and the AVR are connected to your home network router.
MP3 compatibility: Mono or stereo, constant bit rates (CBR) from 8kbps to 320kbps,
variable bit rates (VBR) from lowest to highest quality, with sample rates from 8kHz to 48kHz.
WMA compatibility: Ver. 9.2, stereo CBR with 32kHz – 48kHz sampling rate and 40kbps – 192kbps bit rate, mono CBR with 8kHz – 16kHz sampling rate and 5kbps – 16kbps bit rate, VBR Pass Encoding and Quality Encoding 10 – 98, 44kHz and 48kHz sampling rate.
NOTE:
• A PC must be running Windows Media® Player version 11 or higher, Windows
Media Center version 2.0 or 3.0, or Intel® Media Server. We recommend that any firewalls be turned off, although Windows Media Player may automatically make any necessary adjustments to the firewall settings to allow media sharing.
• An Apple Macintosh computer must be running DLNA (Digital Living Network
Alliance)-compliant software such as HARMAN Media Manager. To download the free HARMAN Media Manager software, go to http://www.locale. harmankardon.com/en-US/hmm/mediamanager.html.
IMPORTANT: Before you can access files located on other devices via the network, each device must first give permission to share files with the AVR:
Home Network
J ugalbandi
Successfully Assimilated
Night Crazy
5:44
• Use the remote’s Transport Control buttons to control playback.
• To access Shufe and Repeat functions, press the remote’s Options button.
When the song is finished playing the remaining contents of the folder will play.
NOTE:
• The Repeat settings are global for Network playback and USB playback.
Changing these settings for one of these sources will change the other source’s settings as well.
• Although video content may appear in the menu, the AVR does not support
video playback from the Network connection.
21
AVR
Operating Your AVR, continued,
and Advanced Functions
Listening to Media via AirPlay
If you have connected the AVR to a network router that has Wi-Fi® capability, you can wirelessly stream audio to it via AirPlay from compatible Apple devices with iOS 4.2 or newer that are joined on the same Wi-Fi network, and from computers that have iTunes
10.1 or newer that are joined on the same Wi-Fi or wired network.
To initiate AirPlay streaming to the AVR:
• To initiate AirPlay streaming from a computer with iTunes, launch iTunes, click on the
AirPlay button that appears at the bottom of the computer’s iTunes window, and select “HK AVR170” in the pop-up list that appears.
HK AVR170
Select
AirPlay
Button
“HK AVR170” From Pop-Up List
• To initiate AirPlay streaming from an iPod, iPhone or iPad device, tap the AirPlay button
on the device’s screen and select “HK AVR 170” in the speaker-selection list that appears.
The AirPlay audio stream will break in and interrupt the source that is currently playing through the AVR. The AirPlay screen will appear on the OSD.
AirPlay
J ugalbandi
The Madagascar W ombat
Laydown Delivery
2:12/00:00
Use the remote’s Transport Control buttons to control playback. To terminate AirPlay streaming and return to the previously playing source, press the
remote’s Back button at any time while the AirPlay screen is displayed.
Selecting a Surround Mode
Selecting a surround mode can be as simple or sophisticated as your individual system and tastes. Feel free to experiment, and you may find a few favorites for certain sources or program types. You can find more detailed information on surround modes in Audio Processing and Surround Sound, page 23.
To select a surround mode, press the OSD Button on the remote to display the Master menu:
MASTER MENU
Source Select
Source Setup
Surround Mode
EzSet/EQ
Manual Setup
Network
System Setup
Use the Up/Down and OK buttons to select Surround Mode. The Surround Mode menu will appear:
SURROUND MODE
A uto Select
Virtual Surround
Stereo
Movie
Music
Video Game
Use the Up/Down and OK buttons to select the desired surround-mode category. Auto Select: For a digital program, such as a movie recorded with a Dolby Digital or DTS
soundtrack, the AVR will automatically use the soundtrack’s native surround format. For 2-channel analog and PCM programs, the AVR uses the Logic 7 Movie, Logic 7 Music or Logic 7 Game mode, depending on the source.
Virtual Surround: When only two main speakers are present in the system, you can use
the Virtual Surround mode to create an enhanced sound eld that virtualizes the missing
speakers. Stereo: When you want 2-channel playback, select the number of speakers you want to
use for playback:
• “2 CH Stereo” uses two speakers.
• “5 CH Stereo” plays the left-channel signal through the front left and surround left
speakers, the right-channel signal through the front right and surround right speakers, and a summed mono signal through the center speaker.
Movie: Select from the following when you want a surround mode for movie playback: Logic 7 Movie, DTS NEO:6 Cinema or Dolby Pro Logic II Movie.
Music: Select from the following when you want a surround mode for music playback: Logic 7 Music, DTS NEO:6 Music or Dolby Pro Logic II Music. The Dolby Pro Logic II Music mode provides some additional settings. See Audio Processing and Surround Sound, on page 23, for more information.
Video Game: Select from the following when you want a surround mode for game playback: Logic 7 Game or Dolby Pro Logic II Game.
After you select the Surround Mode Categopry, use the Left/Right buttons to change the surround mode.
You can also select surround modes using the AVR’s front-panel buttons:
1. Press the Surr Mode button. The Message display will show the surround-mode category and surround mode.
2. To change the surround mode within the surround-mode category, press the Surround
Select Up/Down buttons. Each press will change to the next surround mode.
3. To change the surround-mode category, press the Surr Mode button. Each press will
change to the next surround-mode category.
22
AVR
Advanced Functions, continued
English
Advanced Functions
Much of the adjusting and configuration your AVR requires is handled automatically, with
little intervention required on your part. You can also customize your AVR to suit your
system and your tastes. In this section, we will describe some of the more advanced adjustments available to you.
Audio Processing and Surround Sound
Audio signals can be encoded in a variety of formats that can affect not only the quality of the sound but also the number of speaker channels and the surround mode. You may also manually select a different surround mode, when available.
Analog Audio Signals
Analog audio signals usually consist of two channels – left and right. Your AVR offers several options for analog playback:
Stereo: When you want conventional 2-channel playback, select “2-CH STEREO” as
the surround mode. Sound will be output from the front left and right speakers (and subwoofer, if your system has one).
5-Ch Stereo: When you want to hear stereo sound through all of the system’s speakers
(such as during a party), select “5CH STEREO” as the surround mode. This plays the left-channel signal through the front left and surround left speakers, the right-channel signal through the front right and surround right speakers, and a summed mono signal through the center speaker (in addition to the subwoofer, if your system has one).
• Multi-Channel Surround Modes: Your AVR is able to process 2-channel audio signals to produce multichannel surround sound, even when no surround sound has been encoded in the recording. Among the available modes are the Dolby Pro Logic II, Virtual Surround, DTS NEO:6, and Logic 7 modes. To select one of these modes, see Selecting a Surround Mode, on page 22.
Digital Audio Signals
Digital audio signals offer greater flexibility and capacity than analog signals and allow the encoding of discrete channel information directly into the signal. The result is improved sound quality and startling directionality, since each channel’s information is transmitted discretely. High-resolution recordings sound extraordinarily distortion-free, especially in the high frequencies.
Surround Modes
Surround-mode selection depends upon the format of the incoming audio signal as well as your personal taste. Although there is never a time when all of the AVR’s surround modes are available, there is usually a wide variety of modes available for a given input. Table A8 in the Appendix, on page 32, offers a brief description of each mode and indicates the types of incoming signals or digital bitstreams the mode may be used with. Additional information about the Dolby and DTS modes is available on the companies’ Web sites: www.dolby.com and www.dtsonline.com.
When in doubt, check the jacket of your disc for more information on which surround modes are available. Usually, nonessential sections of the disc, such as trailers, extra materials or the disc menu, are available only in Dolby Digital 2.0 (2-channel) or PCM 2-channel mode. If the main title is playing and the display shows one of these surround modes, look for an audio or language setup section in the disc’s menu. Also, make sure your disc player’s audio output is set to the original bitstream rather than 2-channel PCM. Stop play and check the player’s output setting.
The channels included in a typical 5.1-channel recording are front left, front right, center, surround left, surround right and LFE (low-frequency effects). The LFE channel is denoted as “.1” to represent the fact that it is limited to the low frequencies.
Digital formats include Dolby Digital 2.0 (two channels only), Dolby Digital 5.1, Dolby Digital Plus (7.1), Dolby TrueHD (7.1), DTS-HD High-Resolution Audio (7.1), DTS-HD
Master Audio (7.1), DTS 5.1, DTS 96/24 (5.1), 2-channel PCM modes in 32kHz, 44.1kHz, 48kHz or 96kHz, and 5.1 or 7.1 multichannel PCM. (Your AVR will downmix the discrete
surround back-channel information in 6.1-channel and 7.1-channel recordings into your system’s surround left and surround right channels.)
When the AVR receives a digital bitstream, it detects the encoding method and the number of channels, which is displayed briefly as three numbers, separated by slashes (e.g., “3/2/.1”).
The first number indicates the number of front channels in the signal: “1” represents a monophonic recording (usually an older program that has been digitally remastered or, more rarely, a modern program for which the director has chosen mono as a special effect). “2” indicates the presence of the left and right channels but no center channel. “3” indicates that all three front channels (left, right and center) are present.
The second number indicates whether any surround channels are present: “0” indicates that no surround information is present. “1” indicates that a matrixed surround signal is present. “2” indicates discrete surround left and right channels. (Bitstreams with discrete surround back left and right channel signals will be indicated by a “4,” although the AVR downmixes the surround back-channel information into the surround left and right channels.)
The third number is used for the LFE channel: “0” indicates no LFE channel. “.1” indicates that an LFE channel is present.
Dolby Digital 2.0 signals may include a Dolby Surround flag indicating DS-ON or DS-OFF, depending on whether the 2-channel bitstream contains only stereo information or a downmix of a multichannel program that can be decoded by the AVR’s Dolby Pro Logic decoder. By default, these signals are played in Dolby Pro Logic II Movie mode.
When a PCM signal is received, the PCM message and the sampling rate (32kHz,
44.1kHz, 48kHz or 96kHz) will appear.
When only two channels – left and right – are present, the analog surround modes may be used to decode the signal into multiple channels. If you would prefer a different surround format than the native signal’s digital encoding, press the Surround Modes button to display the Surround Modes menu (see Selecting a Surround Mode, on page 22).
The Auto Select option sets the surround mode to the native signal’s digital encoding, e.g., Dolby Digital, DTS, Dolby TrueHD or DTS-HD Master Audio. For analog 2-channel materials, the AVR defaults to the Logic 7 Movie mode. For Dolby Digital 2.0 programs, the AVR defaults to the Dolby Pro Logic II Movie mode, which creates a 5.1-channel surround-sound presentation from the 2-channel program. If you prefer a different surround mode, select the surround-mode category: Virtual Surround, Stereo, Movie, Music or Video Game. Press the OK button to change the mode.
Each surround-mode category is set to a default surround mode:
• Virtual: Virtual Surround.
• Stereo: 5-CH Stereo.
• Movie: Logic 7 Movie.
• Music: Logic 7 Music.
• Video Game: Logic 7 Game.
You may select a different mode for each category. Below is a complete list of available surround modes. (The actual surround modes available will depend on the number of speakers in your system.)
• Virtual: Virtual Surround.
• Stereo: 2-CH Stereo or 5-CH Stereo.
• Movie: Logic 7 Movie, Dolby Pro Logic II Movie, DTS NEO:6 Cinema.
• Music: Logic 7 Music, Dolby Pro Logic II Music, DTS NEO:6 Music.
• Video Game: Logic 7 Game, Dolby Pro Logic II Game.
Once you have programmed the surround mode for each type of audio, select the line from the Surround Modes menu to override the AVR’s automatic surround-mode selection. The AVR will use the same surround mode the next time you select that source.
Please refer to Table A8 in the Appendix for more information on which surround modes are available with different bitstreams.
23
AVR
Advanced Functions, continued
Dolby Pro Logic II Music Mode Adjustments
When you select Dolby PLII as the music surround mode, additional adjustments become available:
Mode : Music
Dolby PLII Music
Center Width 3
Dimension 0
P anorama Off
Center Width: This setting affects how vocals sound through the three front speakers. A lower number focuses the vocal information tightly on the center channel. Higher numbers (up to 7) broaden the vocal soundstage. Use the Left/Right buttons to adjust this setting.
Dimension: This setting affects the depth of the surround presentation, allowing you to “move” the sound toward the front or rear of the room. The setting of “0” is a neutral default. Setting “F-3” moves the sound toward the front of the room, while setting “R-3” moves the sound toward the rear. Use the Left/Right buttons to adjust it.
Panorama: With the Panorama mode turned on, some of the sound from the front speakers is moved to the surround speakers, creating an enveloping “wraparound” effect. Each press of the OK button toggles the setting On or Off.
Manual Speaker Setup
Your AVR is flexible and may be configured to work with most speakers and to compensate for the acoustic characteristics of your room.
The EzSet/EQ process automatically detects the capabilities of each connected speaker and optimizes the AVR’s performance with your speakers. If you are unable to run EzSet/
EQ calibration, or if you wish to set up your AVR for your speakers manually, use the Manual Setup on-screen menus.
Before beginning, place your loudspeakers as explained in the Place Your Speakers section, on page 10, and connect them to the AVR. Consult the owner’s guide for the speakers or the manufacturer’s Web site for their frequency-range specification. Although you may set the AVR’s individual channel levels “by ear,” an SPL (sound-pressure level) meter purchased at a local electronics store will provide greater accuracy.
Record your configuration settings in Tables A3 and A5 in the Appendix for easy re-entry after a system reset or after the AVR’s Master Power switch has been turned off or the unit has been unplugged for more than four weeks.
Step One – Determine Your Speakers’ Crossover Frequencies
Without using the EzSet/EQ process, the AVR can’t detect how many speakers you’ve
connected to it; nor can it determine their capabilities. Consult the technical specifications for all of your speakers and locate the frequency response, usually given as a range, e.g.,
100Hz – 20kHz (±3dB). Write down the lowest frequency that each of your speakers is capable of playing (100Hz in the above example) as the crossover in Table A6 in the
Appendix.
Step Two – Measure the Speaker Distances
Ideally, all of your speakers would be placed in a circle, with the listening position at the center. However, you may have had to place some speakers a little farther away from the listening position than others. Sounds that are supposed to arrive simultaneously from different speakers may blur, due to different arrival times.
Your AVR provides a Distance adjustment that compensates for these real-world speaker­placement differences.
Measure the distance from each speaker to the listening position, and write it down in Table A3 in the Appendix. Even if all of your speakers are the same distance from the listening position, enter your speaker distances as described in Set the Speaker Distances, on this page 25.
Step Three – Manual Setup Menu
Now you are ready to program the AVR. Sit in your usual listening position, and make the room as quiet as possible.
With the AVR and video display turned on, press the OSD button to display the menu system and select Manual Setup. The Manual Setup menu will appear:
Manual Setup
Number of Spkrs
Sub Mode
Crossover
Distance
Level Adjust
NOTE: To save your settings, press the remote’s Back button
For best results, adjust the submenus in this order: Number of Spkrs (Speakers), Crossover, Sub Mode, Distance and Level Adjust.
Number of Spkrs
This selection lets you program the correct setting for each speaker group. The settings in this menu affect the remainder of the speaker-setup process and the availability of various surround modes at any time.
Select “On” when the speakers are present in the system; select “Off” for positions where no speakers are installed. The Front Left & Right setting is always “On” and may not be disabled.
Number of Spkrs
Left/Right On
Center On
Surround On
SubWoofer On
NOTE: This frequency is not the same as the “Crossover Frequency” that may be listed in the speaker’s specifications.
For the subwoofer, write down the transducer size. The AVR’s bass management
determines which speakers will be used to play back the low-frequency (bass) portion of the source program. Sending the lowest notes to small satellite speakers will result in bad sound and may even damage the speakers. The highest notes may not be heard at all through the subwoofer.
With proper bass management, the AVR divides the source signal at a crossover point. All information above that crossover point is played through your system’s speakers, and all information below the crossover point is played through the subwoofer. This way, each loudspeaker in your system will perform at its best, delivering a more powerful and enjoyable sound experience.
24
When you have finished, press the remote’s Back button.
AVR
Advanced Functions, continued
English
Crossover
After you return to the Manual Setup menu, navigate to the Crossover line and press the OK button to display the Crossover menu.
Crossover
Left/Right 100Hz
Center 100Hz
Surround 1 00Hz
Sub 10inch
Refer to Table A5 for each speaker’s crossover frequency.
NOTE: The AVR will let you adjust settings only for those speaker groups you set to On in the Number of Speakers menu.
For each speaker group, select one of these eight crossover frequencies: LARGE, 40Hz, 60Hz, 80Hz, 100Hz, 120Hz, 150Hz or 200Hz. If the speaker’s crossover frequency is below 40Hz, select the rst option, LARGE. This setting doesn’t refer to the speaker’s physical size but to its frequency response, which is also called “full range.”
Specify the size of the subwoofer’s transducer as 8, 10, 12 or 15 inches. The AVR always sets the subwoofer crossover to 100Hz but uses the transducer size for equalization.
Write down the settings in Table A5 in the Appendix. When you have finished entering the settings, press the remote’s Back button.
Sub Mode
After you return to the Manual Setup menu, navigate to the Sub Mode line and press the OK button to display the Sub Mode menu. This setting depends upon the Crossover setting you selected for the left and right speakers.
• If you set the Left/Right speakers to a numeric crossover frequency, the subwoofer
setting will always be SUB. All low-frequency information will always be sent to the subwoofer. If you don’t have a subwoofer, either upgrade to full-range front left and right speakers or add a subwoofer at the earliest opportunity.
• If you set the front speakers to LARGE, select one of the three following settings for
the subwoofer:
L/R+LFE: This setting sends all low-frequency information to the subwoofer, including a) low-frequency information that is also played through the front left and right speakers and b) the special low-frequency effects (LFE) channel information.
OFF: Select this setting when no subwoofer is in use. All low-frequency information will be sent to the front left and right speakers.
LFE: This setting plays low-frequency information contained in the full-range program channels through the front left and right speakers, and directs only the LFE-channel information to the subwoofer.
When you have finished entering the settings, press the remote’s Back button.
Set the Speaker Distances
As described above in Step Two, when you measured the distances from each of your speakers to the listening position, your AVR provides an adjustment that compensates for the different distances so that the sound from each speaker will reach the listening position at the proper time. This process will improve the clarity and detail of the sound.
After you return to the Manual Setup menu, navigate to the Distance line and press the OK button to display the Distance menu.
Distance
FL 3.0M
CEN 3.0M
FR 3.0M
SR 3.0M
SL 3.0M
Sub 3.0M
Delay Reset Off
Unit Meter
Enter the distance from each speaker to the listening position that you measured in Step Two and recorded in Table A3 in the Appendix (see page 30). Select a speaker, then use the Left/Right buttons to change the measurement. You can enter distances between 0 and 30 feet (9m). The default distance for all speakers is 10 feet (3m).
The default unit of measurement is meters. To change the unit to feet, scroll down to the Unit line and press the Left/Right buttons.
When you have finished entering the settings, press the remote’s Back button.
Step Four – Setting Channel Output Levels Manually
For a conventional stereo AVR, a simple balance control adjusts the stereo imaging by varying the relative loudness of the left and right channels. In a home theater system with up to five main channels plus a subwoofer, achieving proper imaging becomes both more critical and more complex. The goal is to ensure that each channel is heard at the listening position with equal loudness (when signals of equal loudness are played through them).
Your AVR’s EzSet/EQ calibration can handle this critical task for you simply and
automatically. However, the AVR’s Level Adjust menu allows you to calibrate the levels manually, either using the system’s built-in test tone or while playing source material.
After you return to the Manual Setup menu, navigate to the Level Adjust line and press the OK button to display the Level Adjust menu.
Level Adjust
T est T one Off
FL 0dB
CEN 0dB
FR 0dB
SR 0dB
SL 0dB
Sub 0dB
Channel Reset Off
T est T one SEQ Manual
All of the system’s speakers will appear with their current level settings. You can adjust each speaker’s level between –10dB and +10dB in 1dB increments.
While making adjustments, you can measure the channel levels in one of these ways:
• Preferably, use a handheld SPL meter set to C-weighting, slow scale. Adjust each
speaker so that the meter reads 75dB when the AVR’s built-in test noise is playing.
• By ear. Adjust the levels so that the test tone sounds equally loud to you when it plays
through each speaker.
25
AVR
Advanced Functions, continued
To set your levels using the AVR’s internal test tone, select the menu’s Test Tone Seq line and use the Left/Right buttons to select between Auto and Manual. After selecting Auto or Manual, move the cursor to the Test Tone line and use the Left/Right buttons to change the setting to On.
Auto: The test tone will automatically circulate to all speakers, as indicated by the highlight bar. Use the Left/Right buttons to adjust the level for any speaker when the test tone is paused there. Use the Up/Down buttons to move the cursor to another line, and the test tone will follow the cursor. To stop the test tone, use the Up/Down buttons to move the cursor out of the screen’s speaker-listings area.
Manual: The test tone will stay on the current speaker until you use the Up/Down buttons to move it to another speaker. Use the Left/Right buttons to adjust the level for the speaker through which the test tone is playing.
If you are listening to an external source while you set your output levels, set Test Tone to Off, use the Up/Down buttons to navigate to each speaker, and use the Left/Right buttons to adjust the speaker’s level while the source plays.
NOTE: If you are using a handheld SPL meter with external source material, such as a test disc or an audio selection, play it and adjust the AVR’s master volume control until the meter measures 75dB. Then adjust the individual speaker levels.
Channel Reset: To reset all channel levels to their factory defaults of 0dB, select this line
and press the Left/Right buttons. When you have finished adjusting the speaker levels, record the settings in Table A5
in the Appendix. Then press the remote’s Back button to return to the previous menu screen, or press the remote’s OSD button to exit the menu system.
Notes on Setting Speaker Volumes in Home Theater Systems:
While setting your system’s individual speaker volume levels is ultimately up to your personal taste, here are some ideas you may find helpful:
• For lms and video-music programs, your overall goal should be to create an
enveloping, realistic sound field that draws you into the film or music program without drawing your attention away from the action on the screen.
• For multichannel music recordings, some music producers will create a sound eld that
places the musicians all around you; others will create a sound field that places the musicians in front of you, with more subtle ambience in the surround speakers (as you would experience in a concert hall).
• In most 5.1-channel lm soundtracks, the surround speakers are not intended to be
as loud or as active as the front speakers. Adjusting the surround speakers so they are always as loud as the front speakers could make dialogue difficult to understand and will make some sound effects sound unrealistically loud.
Notes on Setting Subwoofer Volume:
• Sometimes the ideal subwoofer volume setting for music is too loud for lms, while the
ideal setting for films is too quiet for music. When setting the subwoofer volume, listen to both music and films with strong bass content and find a “middle ground” volume level that works for both.
• If your subwoofer always seems too loud or too quiet, you may want to place it in a
different location. Placing the subwoofer in a corner will always tend to increase its bass output, while placing it away from any walls or corners will always tend to lessen its bass output.
System Setup
The AVR’s System Setup menu lets you customize the way many of the AVR’s features
operate. Press the OSD button and navigate to the System Setup line. Press the OK button to display the System Setup menu.
VFD Fade Time Out: Some people find the brightness of the AVR’s front-panel display distracting during movies or listening sessions. It’s possible to dim the front-panel display completely using the remote’s Display Dimmer button (see System Remote Control Functions, on pages 8 and 9). The VFD Fade Time Out sets the display to remain dark most of the time, lighting up only when a button is pressed or a remote command is received, and going dark again five seconds after the last command. The feature also causes the display to light up only when a button is pressed but the display immediately begins to fade to dark. This setting allows you to program the length of the fade time. Select a time-out period of between three and ten seconds, or select Off if you prefer to leave the displays on at all times or to use the Display Dimmer button.
Volume Default and Default Volume Set: These two settings are used together to program the volume level the AVR defaults to when you turn it on. Set Volume Default to On, and then set the Default Volume Set to the desired turn-on volume. When Volume Default is set to Off, the AVR will turn on at the last-used volume setting from the previous listening session.
HDMI Audio To TV: This setting determines whether HDMI audio signals are passed through the HDMI Monitor Out connector to the video display. In normal operation, leave this setting at Off, as audio will be played through the AVR. To use the TV by itself, without the home theater system, turn this setting to On. In this case, you will need to mute the TV’s speakers (or switch the setting to Off) when using the AVR for audio.
Semi OSD Time Out: Program the amount of time (2 to 5 seconds) the two-line semi­OSD status messages remain on screen, or deactivate the semi-OSD display altogether if you find it distracting. These messages will continue to appear on the AVR’s front-panel display.
Full OSD Time Out: Program the amount of time (20, 30, 40 or 50 seconds) the full OSD menus remain visible on screen. The full OSD system may not be deactivated.
HDMI Link: This setting allows the communication of control information among the HDMI devices in your system. Turn this setting to On to allow control communication among the HDMI devices; turn the setting to Off to forbid control communication.
Adjust Lip Sync: This setting lets you resynchronize the audio and video signals from
a source to eliminate a “lip sync” problem. Lip sync issues can occur when the video portion of a signal undergoes additional processing in either the source device or the video display. Use the Left/Right buttons to delay the audio by up to 180ms.
Upgrade Software: If a software upgrade is released for your AVR, installation instructions will be available in the Product Support section of the Web site or from Harman Kardon customer service. At that time, access this submenu to install the software upgrade.
IMPORTANT: During a system upgrade, do not power off the AVR or use any of its controls. Doing so could permanently damage the AVR.
Advanced Remote Control Programming
Programming an Unused Source Selector Button to Control a Different Device
You can program unused Source Selector buttons to control devices that are different than they are set up for at the factory. For example, you can program the Server button to control a second TV set.
1. Locate the code numbers for the device you want to control from the tables in Appendices 10 – 18, on pages 37 – 46.
2. Turn on the device you want to control.
3. Press the unused Source Selector button that you want to program for three seconds. The button’s LED will turn on and Program Indicator LED will flash.
4. Press the Source Selector button that corresponds to the type of device you want to control. (For example, if you want to control a TV, press the TV Source Selector button.) The unused Source Selector button’s LED will flash once.
5. Aim the remote toward the device you want to control and use the Number buttons to
enter first code number. The Program Indicator LED will flash. If you have selected the correct code number the device will turn off. If it does not turn off, enter the next code number from the table. When the device turns off, proceed to step 6.
6. Press the unused Source Selector button from Step 3. That Source Selector button’s LED will turn off and the Program Indicator LED will flash green three times.
The remote will now control the device when the formerly unused Source Selector button is pressed.
Remote Channel-Control Punch-Through
The punch-through feature allows you to operate one component while setting certain groups of controls to operate another component. For example, while using the AVR controls for surround modes and other audio functions, you may also use the remote to operate the transport controls of your Blu-ray Disc player. Or while using the remote to control video functions on your TV, you may also use the remote to change channels on your cable box.
26
AVR
Advanced Functions, continued
English
To program punch-through control while operating any device:
1. For three seconds, press and hold the Source Selector button (or the AVR button) for the main device the remote will be operating. The Program Indicator LED will flash, indicating that the remote is in Program mode and that you may release the button.
2. Select the type of punch-through programming.
a) To program volume-control punch-through, press the Volume Up button. b) To program channel-control punch-through, press the Volume Down button. c) To program transport-control punch-through, press the Play transport-control
button.
3. Press the Source Selector button for the device whose volume, channel or transport­controls you will use while operating the device selected in the first step. The Program Indicator LED will flash to confirm.
To undo punch-through programming, follow the same steps as above, but press the same Source Selector button in Steps 1 and 3.
Programming Macro Commands
Each of the AVR remote’s four Macro buttons and the Power On button (see System Remote Control Functions, on pages 8 and 9) can be programmed to send out up to
19 commands at one time from a single button push. Any AVR remote control button’s function from any mode (except the Mute button, the Dim button and the Channel Up/ Down buttons) can be programmed into a macro.
NOTE: Use caution when programming complicated macros. It isn’t possible to program a pause or delay before sending additional commands after a “Power On” command, and the component may not be ready to respond to commands immediately after powering on.
To program a macro:
1. Simultaneously press one of the four Macro buttons, or the Power On button, and the Mute button to enter the Programming mode.
2. Press in up to 19 commands that you want stored in that Macro button. Press the Source Selector button for each device (or AVR button for the AVR itself) before you enter individual commands. This step counts as one of the 19 commands allowed for each Macro.
3. For the Power On command, DO NOT press the Power On button. Press the Mute button instead.
4. Press the Power Off button to program the Power Off command.
5. Press the CH+ button to end the programming process and save the macro.
It isn’t possible to “edit” a command within a macro. However, you may erase the macro as follows:
1. Simultaneously press and hold the Mute button and the Macro button containing the macro until the Program Indicator LED flashes.
2. Press the Channel Down button to erase the macro.
To execute a macro, press the Macro button (or the Power On button) into which you programmed the macro. Aim the remote at the AVR and the other components until all of the macro commands have been executed.
Sleep Timer
The sleep timer sets the AVR to play for up to 90 minutes and then turn off automatically. Press the Sleep button on the remote, and the time until turn-off will be displayed on the
front-panel Message display and on a connected TV. Each additional press of the Sleep button decreases the play time by 10 minutes, with a maximum of 90 minutes. The SLEEP OFF setting disables the sleep timer.
When the sleep timer has been set, the front-panel display will automatically dim to half brightness.
If you press the Sleep button after the timer has been set, the remaining play time will be displayed. Press the Sleep button again to change the play time.
Resetting the Remote
To reset the remote to its factory-default condition, simultaneously press and hold any Source Selector button and the “0” Number button. When the Program Indicator LED flashes amber, enter the code “333.” When the green LED goes out, the remote control will be reset.
Processor Reset
If the AVR behaves erratically after a power surge, first turn off the rear-panel Main Power switch and unplug the AC power cord for at least 3 minutes. Plug the cord back in and turn the AVR on. If this procedure doesn’t help, reset the AVR’s processor as described below.
NOTE: A processor reset erases all user configurations, including video resolution, speaker and level settings, and tuner presets. After a reset, reenter all of these settings from your notes in the Appendix worksheets.
To reset the AVR’s processor:
1. Press the front-panel Standby/On switch to place the unit in the Standby mode (the Power Indicator LED will turn amber).
2. Press and hold the front-panel Surround Mode button for at least 5 seconds until the RESET message appears on the front-panel Message display.
If the AVR does not function correctly after a processor reset, contact an authorized Harman Kardon service center for assistance. Authorized service centers may be located
by visiting our Web site at www.harmankardon.com.
Memory
If the AVR is unplugged or experiences a power outage, it will retain your user settings for up to four weeks.
Recording
Depending on the Record Out settings you made for each source in the Source Setup menu (see System Setup, on page 26, for more information), analog or digital audio signals, as well as composite video signals, are normally available at the appropriate recording output connectors. To make a recording, connect your audio or video recorder to the appropriate AVR output connectors as described in the Making Connections section, on page 13, insert blank media in the recorder and make sure the recorder is turned on and recording while the source is playing. Refer to the recording device’s instructions for complete information about making recordings.
NOTE: Please make certain that you are aware of any copyright restrictions on any material you record. Unauthorized duplication of copyrighted materials is prohibited by law.
27
AVR
Troubleshooting
Symptom Cause Solution
Troubleshooting
Unit does not function when Main Power switch is turned on
Front-panel Message display lights, but there's no sound or picture
No sound from any speaker; PROTECT message appears on Message display
No sound from center or surround speakers • Incorrect surround mode
Unit does not respond to remote control commands • Weak batteries in remote
Intermittent buzzing in tuner • Local interference • Move the AVR or antenna away from computers,
Unable to activate remote control Programming mode • Source Selector button is not held for at least 3 seconds • Be sure to hold the Source Selector button for at least
• No AC power • Ensure that the power cord is plugged into a live AC
• Intermittent input connection
• Mute is on
• Volume control is turned down
• Amplier is in protection mode due to possible short
circuit
• Amplifier is in protection mode due to internal problems
• Program material is monophonic
• Incorrect speaker configuration
• Program material is stereo
• AVR not selected
• Remote sensor is obscured
power outlet
• Check if the AC outlet is switch-controlled
• Secure all input and speaker connections
• Press Mute button
• Turn up Volume control
• Check all speaker wires at speaker and AVR
connections for crossed wires
• Contact your local Harman Kardon service center
• Select a surround mode other than stereo
• Mono programs contain no surround information
• Check the speaker configuration in the setup menu
• The surround decoder may not create center- or
surround-channel information from nonencoded stereo programs
• Change batteries in remote
• Press the Setup/AVR button
• Ensure that the AVR’s front-panel remote sensor is in
the line of sight of the remote
fluorescent lights, motors or other electrical appliances
3 seconds
Additional information on troubleshooting possible problems with your AVR and installation-related issues may be found in the list of “Frequently Asked Questions,” which is located in the Product Support section of our Web site: www.harmankardon.com
28
AVR
Specifications
Specifications
English
Audio Section
Stereo power: 100W per channel,
two channels driven @6/8 ohms,
1kHz, <1.0% THD
Multichannel power: 100 watts per channel
two channels driven
@ 6/8 ohms, 1 kHz, <1.0% THD
Input sensitivity/impedance: 250mV/27k ohms
Signal-to-noise ratio (IHF-A): 100dB
Surround system adjacent-channel separation: Dolby Pro Logic/PLII:
40dB Dolby Digital: 55dB DTS: 55dB
Frequency response: 10Hz – 100kHz
High instantaneous-current capability (HCC): ±34 amps
Transient intermodulation distortion (TIM): Unmeasurable
FM Tuner Section
Frequency range: 87.5 – 108.0MHz
Usable sensitivity IHF: 1.3µV/13.2dBf
Signal-to-noise ratio (mono/stereo): 70dB/68dB
Distortion (mono/stereo): 0.2%/0.3%
Stereo separation: 40dB @ 1kHz
Selectivity (±400kHz): 70dB
Image rejection: 80dB
IF rejection: 80dB
Video Section
Television format: NTSC (AVR 1700);
PAL (AVR 170/AVR 170/230C)
Input level/impedance: 1Vp-p/75 ohms
Output level/impedance: 1Vp-p/75 ohms
Video frequency response (composite video): 10Hz – 8MHz (–3dB)
HDMI: witn 3D and 12-bit Deep Color
General Specifications
Power requirement: 120V AC/60Hz
(AVR 1700); 220V – 240V AC/50Hz (AVR 170/AVR 170/230C)
Power consumption (maximum): 260W (AVR 1700)
240W (AVR 170/ AVR 170/230C)
<0.5W/Eco Standby mode
Dimensions (W x H x D): 17-5/16" x 6-1/2" x 14-13/16"
(440mm x 165mm x 377mm)
Weight 12.8 lb (5.8kg)
AM Tuner Section
Frequency range: 520kHz – 1710kHz
(AVR 1700)
522kHz – 1620kHz
(AVR 170/AVR 170/230C)
Signal-to-noise ratio: 38dB
Usable sensitivity (loop): 500µV
Distortion (1kHz, 50% mod): 1.0%
Selectivity (±10kHz): 30dB
29
AVR
Appendix – Default settings, worksheets, remote product codes
Table A1 – Recommended Source Component Connections
Appendix
Device Type
Cable TV, Satellite, HDTV or other device that delivers television programs
DVD player, Blu-ray Disc player Disc • HDMI 2 Input • HDMI 2 Input
HDMI-capable music server Server • HDMI 3 Input • HDMI 3 Input
HDMI-capable game console Game • HDMI 5 Input • HDMI 5 Input
HDMI-capable DVR or set-top box STB • HDMI 6 Input • HDMI 6 Input
Analog audio device
Home network
iPod or iPhone
Auxiliary source device Aux • Front-Panel Aux Input • Component Video 1 Input
Note: Table A1 is a guideline; you may need to make adjustments to fit your system.
Table A2 – Speaker/Channel Setting Defaults
Speaker
Left/Right Speaker
Center Speaker ON
Default Setting Your Setting
ON
AVR Source
Cable/Sat • HDMI 1 Input • HDMI 1 Input
Audio • Analog Audio 2 • Not required
Network • Network • Not required
USB • USB port • Not required
Default Audio Connection Default Video Connection
Table A3 – Distance Settings
Speaker Positions
Front Left
Center
Your Distances from Speaker to Listening Position
Surround Speaker ON
Subwoofer
Left/Right Speaker Crossover
Center Speaker Crossover
Surround Speaker Crossover
LFE
Sub Mode
ON
100Hz
100Hz
100Hz
PRESENT
SUB
Front Right
Surround Right
Surround Left
Subwoofer
A/V Sync Delay
0mS
Table A4 – Source Settings
Source Cable/Sat
Title
Video Input N/A N/A N/A
Audio Input
Record Out N/A N/A N/A
TV
HDMI Audio Return Channel
Disc Server Aux Game STB Audio Radio USB Network
Internal Tuner
Network Connector
30
AVR
Table A5 – Speaker/Channel Settings
Appendix
English
Front Left
Number of Speakers
Crossover
Distance
Channel Level Adjust
ON
Front Right
Center Surround Left Surround Right Subwoofer
Table A6 – Remote Control Codes
Source Selector Connected Device Remote Control Code
Cable/Sat
TV
Disc
Server
Aux
Game
STB
Audio
Table A7 – System Settings
Feature
VFD Fade Time-Out
Volume Default OFF
Default Vol Set –25dB
HDMI Audio to TV OFF
Semi-OSD Time-Out
Full-OSD Time-Out
HDMI Link
HDMI ARC
Default Setting
OFF
5 Seconds
20 Seconds
OFF
OFF
Your Setting
31
AVR
Table A8 – Surround Modes
Surround Mode Description Incoming Bitstream or Signal
Appendix
Dolby Digital Provides up to five separate main audio channels and a dedicated low-frequency
effects (LFE) channel.
Dolby Digital Plus An enhanced version of Dolby Digital encoded more efficiently, Dolby Digital Plus
has the capacity for additional discrete channels and for streaming audio from the Internet, all with enhanced audio quality. Source material may be delivered via an HDMI connection or decoded to Dolby Digital or PCM and transmitted via coaxial or optical digital audio.
Dolby TrueHD Dolby TrueHD is an expansion of MLP Lossless™ audio, the same format used on
DVD-Audio discs. Dolby TrueHD adds the features found in Dolby Digital, such as night mode settings, while delivering fully lossless audio that is a true reproduction of studio master recordings.
Dolby Digital Stereo Delivers a 2-channel downmix of Dolby Digital materials.
Dolby Pro Logic II Mode Group Analog decoder that derives five full-range, discrete main audio channels from
matrix surround-encoded or 2-channel analog sources. Four variants are available.
Dolby Pro Logic II Movie Variant of Dolby Pro Logic II that is optimized for movie and television programs.
• Dolby Digital 1/0/.0 or .1, 2/0/.0 or .1, 3/0/.0 or .1,
• Dolby Digital EX (played as 5.1)
• Dolby Digital Plus decoded and delivered via coaxial or optical
• Dolby Digital Plus via HDMI connection (source device decodes to
• Blu-ray Disc or HD-DVD encoded with Dolby TrueHD, delivered
• Dolby Digital 1/0/.0 or .1, 2/0/.0 or .1, 3/0/.0 or .1,
• Dolby Digital EX
See below
• Dolby Digital 2.0 or 2.1
• Analog (two-channel)
• Tuner
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)
2/1/.0 or .1, 2/2/.0 or .1, 3/2/.0 or .1
connection
Dolby Digital when a coaxial or optical connection is used)
via HDMI
2/1/.0 or .1, 2/2/.0 or .1, 3/2/.0 or .1
Dolby Pro Logic II Music Variant of Dolby Pro Logic II that is optimized for music selections. Allows
Dolby Pro Logic II Game Variant of Dolby Pro Logic II that emphasizes use of the surround channels and
Dolby Pro Logic Original version of Dolby Pro Logic that steered a mono signal containing
Virtual Speaker Simulates 5.1 channels when only two speakers are present or a more enveloping
DTS Digital
adjustment of sound-field presentation in three dimensions:
• Center Width (adjusts width of vocal soundstage)
• Dimension (adjusts depth of soundstage)
• Panorama (adjusts wraparound surround effect)
subwoofer for total immersion in the video gaming experience.
information below 7kHz to the surround channels.
sound field is desired.
Using a different encoding/decoding method from Dolby Digital, DTS Digital also provides up to five discrete main channels, plus an LFE channel.
• Dolby Digital 2.0 or 2.1
• Analog (two-channel)
• Tuner
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)
• Dolby Digital 2.0 or 2.1
• Analog (two-channel)
• Tuner
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)
• Dolby Digital 2.0 or 2.1
• Analog (two-channel)
• Tuner
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)
• Dolby Digital
• Analog (two-channel)
• Tuner
• PCM (32kHz, 44.1kHz or 48kHz)
• DTS 1/0/.0 or .1, 2/0/.0 or .1, 3/0/.0 or .1, 3/1/.0 or .1, 2/2/.0 or
• DTS-ES Matrix (played as 5.1)
• DTS-ES Discrete (played as 5.1)
.1, 3/2/.0 or .1
32
AVR
Table A8 – Surround Modes (cont.)
Surround Mode Description Incoming Bitstream or Signal
Appendix
English
DTS-HD DTS-HD is a high-definition audio format that complements the high-definition video
DTS-HD Master Audio DTS-HD Master Audio technology delivers bit-for-bit reproductions of studio master
DTS Stereo Delivers a 2-channel downmix of DTS Digital materials or presents a matrix-
DTS Neo:6 Cinema Delivers an enhanced 5.1-channel surround-sound experience for movies • Analog (two-channel)
DTS Neo:6 Music Delivers an enhanced 5.1-channel surround-sound experience for music • Analog (two-channel)
Logic 7 Mode Group
found on Blu-ray Disc and HD-DVD discs. It is transmitted using a DTS core with high-resolution extensions. Even when only DTS 5.1 surround sound is desired (or
available, if the multizone system is in use), the higher capacity of high-resolution
discs serves up DTS at twice the bit rate used on DVD-Video discs.
recordings for an incredibly accurate performance.
encoded surround presentation.
A HARMAN proprietary technology, Logic 7 enhances two-channel and matrix­encoded recordings by deriving separate information for the surround back channels. It provides more accurate placement of sound, improves panning and expands the sound field, even when used with 5.1-channel systems. Logic 7
technology uses 96kHz processing and is available in 5.1 mode. Three variants are
available.
• Blu-ray Disc or HD-DVD discs encoded with DTS-HD modes,
delivered via HDMI connection
• Blu-ray Disc or HD-DVD discs encoded with DTS-HD Master
Audio technology, delivered via HDMI connection
• DTS 1/0/.0 or .1, 2/0/.0 or .1, 3/0/.0 or .1, 3/1/.0 or .1, 2/2/.0 or .1, 3/2/.0 or .1
• DTS 96/24
• DTS-ES Matrix
• AM/FM radio
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz
• AM/FM radio
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)
See below
Logic 7 Movie
Logic 7 Music
Logic 7 Game
5-Channel Stereo Useful for parties, the left- and right-channel information is played through both
2-Channel Stereo Turns off all surround processing and plays a pure 2-channel signal or a downmix
Especially suited to two-channel sources containing Dolby Surround or matrix encoding, Logic 7 Movie mode increases center-channel intelligibility.
The AVR is programmed at the factory to default to this mode for two­channel signals. Logic 7 Music mode is well suited to conventional two­channel music recordings.
Use Logic 7 Game mode to enhance enjoyment of video-game consoles.
the front and surround speakers on each side, while the center speaker plays a summed mono mix.
of a multichannel signal. The signal is digitized and bass management settings are
applied, making it appropriate when a subwoofer is used.
• Analog (two-channel)
• Tuner
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)
• Analog (two-channel)
• Tuner
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)
• Analog (two-channel)
• Tuner
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)
• Analog (two-channel)
• Tuner
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)
• Analog (two-channel; DSP downmix available for multichannel)
• Tuner
• PCM (32kHz, 44.1kHz, 48kHz, 96kHz)
33
AVR
Appendix
Refer to the numbered buttons when using the Remote Control Function List
34
AVR
Appendix
Table A9 – Remote Control Function List
Button
No.
Name
01
Power On Power On Power On Power On Power On Power On/Off Power On Power On Power On Power On
02
Power Off Power Off Power Off Power Off Power Off TV Power Power Off Power Off Power Off Power Off
03 Mute Mute Mute Mute Mute Mute Mute Mute Mute Mute Mute
04 AVR AVR Select AVR Select AVR Select AVR Select AVR Select AVR Select AVR Select AVR Select AVR Select AVR Select
05 Cable/Sat Cable/Sat Select Cable/Sat Select Cable/Sat Select Cable/Sat Select Cable/Sat Select Cable/Sat Select Cable/Sat Select Cable Select Sat Select Cable/Sat Select
06 TV TV Select TV Select TV Select TV Select TV Select TV Select TV Select TV Select TV Select TV Select
07 Disc Disc Select Disc Select Disc Select TV Select Disc Select Disc Select Disc Select Disc Select Disc Select Disc Select
08 Server Server Select Server Select Server Select Server Select Server Select Server Select Server Select Server Select Server Select Server Select
09 Aux Aux Select Aux Select Aux Select Aux Select Aux Select Aux Select Aux Select Aux Select Aux Select Aux Select
10 Game Game Select Game Select Game Select Game Select Game Select Game Select Game Select Game Select Game Select Game Select
11 STB STB Select STB Select STB Select STB Select STB Select STB Select STB Select STB Select STB Select STB Select
12 Audio Audio Select Audio Select Audio Select Audio Select Audio Select Audio Select Audio Select Audio Select Audio Select Audio Select
13 Radio Radio Select Radio Select Radio Select Radio Select Radio Select Radio Select Radio Select Radio Select Radio Select Radio Select
14 USB USB Select USB Select USB Select USB Select USB Select USB Select USB Select USB Select USB Select USB Select
15 Network Network Select Network Select Network Select Network Select Network Select Network Select Network Select Network Select Network Select Network Select
16 CH+ Audio Channel + Channel + Audio Channel + Channel + Channel +
17 Test Tone Test Tone Find Find
18 CH. Channel Audio or Playlist Audio Status
19 Vol Up Volume Up Volume Up Volume Up Volume Up Volume Up Volume Up Volume Up Volume Up Volume Up Volume Up
20 CH- Disc Menu or Title
21 Tone Tone Controls
22 Delay Delay Adjust Repeat Repeat Delay Adjust
23 Vol Down Volume Down Volume Down Volume Down Volume Down Volume Down Volume Down Volume Down Volume Down Volume Down Volume Down
24 Back/Last Back Return or Status Return or Exit Enter Previous Channel
25 Options/Menu Options Menu or Setup
26 Up Move/Adust Up Up Up Up Up Up Up Up Up Up
27 Left Move/Adjust Left Left Left Left Left Left Left Left Left Left
28 OK OK Enter Enter Select Enter Select Enter Enter Enter Enter
29 Right Move/Adjust Right Right Right Right Right Right Right Right Right Right
30 Down
31 OSD OSD
32 Sleep/Guide Sleep Disc Menu/Title Status/Display DVD menu Disc Menu Info Info Sleep
33 1 1 1 1 1 1 1 1 1 1 1
34 2 2 2 2 2 2 2 2 2
35 3 3 3 3 3 3 3 3 3 3 3
AVR
Function
Move/Adjust
Down
DVD
Down Down Down Down Down Down Down Down Down
HD Mode/SUB
On/Off
Blu-ray Disc
Player
Disc Menu or Top
Menu
PIP Audio or
PopUp Menu
Options or Popup/
Title Menu
Home/Subtitle OSD Info OSD OSD
Game TV TiVo/DVR
Scan Down Channel - Channel - Title Channel - Channel - Channel -
Prev CH or Instant
Replay
Start Menu Menu Setup Menu Menu Options
DMC Music
Server
V-Off Tone Controls
Return or Back Previous Channel Previous Channel Back
Cable Tuner
Satellite
Tuner
2 2
iPod/USB
English
35
AVR
Appendix
Table A9 – Remote Control Function List (cont.)
Button
No.
Name
36 4 4 4 4 4 4 4 4 4 4 4
37 5 5 5 5 5 5 5 5 5 5 5
38 6 6 6 6 6 6 6 6 6 6 6
39 7 7 7 7 7 7 7 7 7 7 7
40 8 8 8 8 8 8 8 8 8 8 8
41 Direct Direct Tuner Entry
42 9 9 9 9 9 9 9 9 9 9 9
43 0 0 0 0 0 0 0 0 0 0 0
44 Clear Clear Clear Clear Clear Exit Clear Clear
45 Tuning Up Tuning Up Next Chapter Program (Red)
46 Memory Direct Tuner Entry Angle Bookmark (Green)
47 TUN-M Tuning Mode
48 Preset Up Preset Tune Up Slow Forward Zoom (Blue) X Jump Down/Skip Source/Menu Music Alt
49 Tuning Down Tuning Down Prev Chapter Setup/Settings Sleep
50 Night Night Mode Subtitle Find/Subtitle Subtitle Subtitle
D. Skip
51
(AVR 1700);
RDS (AVR 170)
52 Preset Down
53 M1 Macro 1 Macro 1 Macro 1 Macro 1 Macro 1 Macro 1 Macro 1 Macro 1 Macro 1 Macro 1
54 M2 Macro 2 Macro 2 Macro 2 Macro 2 Macro 2 Macro 2 Macro 2 Macro 2 Macro 2 Macro 2
55 M3 Macro 3 Macro 3 Macro 3 Macro 3 Macro 3 Macro 3 Macro 3 Macro 3 Macro 3 Macro 3
56 M4 Macro 4 Macro 4 Macro 4 Macro 4 Macro 4 Macro 4 Macro 4 Macro 4 Macro 4 Macro 4
57 Skip Down Skip – Step – Skip – Scan – Thumbs Down Skip – Skip – (DVD) Skip – (DVD) Skip –
58 Skip Up Skip + Step + Skip + Scan + Thumbs Up Skip + Skip + (DVD) Skip + (DVD) Skip +
59 Dim Dimmer Dimmer Dimmer
60 Rewind
61 Play
62 FF


63 Record Open/Close Open/Close Record/Pause Record Record Record Record Record Record
64 Stop Stop Stop Stop Stop Stop Stop Stop Stop Stop Stop
65 Pause Pause Pause Pause Pause Pause Pause Pause Pause Pause Pause
AVR
Function
Disc Skip (AVR
1700); RDS Mode (AVR 170)
Preset Tune
Down
DVD
Chapter+ or
Zoom
Disc Skip Angle Play Mode
Slow Rev A-B Zoom
Blu-ray Disc
Player
Thumbnail
(Yellow)
Game TV TiVo/DVR
Cancel Mark/Window PPV Cancel
Repeat/Live TV Angle FAV FAV
Jump Up/Slow A-B Bypass Next
DMC Music
Server
Cable
Tuner
Satellite
Tuner
iPod/USB
R. Search R. Search R. Search Rewind Rewind R. Search R. Search R. Search R. Search R. Search
Play Play Play R. Play/F. Play Play Play Play Play (DVD) Play (DVD) Play
F. Search F. Search F. Search Fast Fwd Fast Fwd F. Search F. Search F. Search F. Search F. Search
36
AVR
Table A10 – Remote Control Product Codes: TV
Appendix
English
TV Manufacturer/Brand Setup Code Number
A MARK 132 122
ACER 143 167
ADMIRAL 192 105 088 023
ADVENT 151
AIWA 027 110
AKAI 053 093 089 056 042 022 020 011
AKAL 160 123
AKURA 020
ALBA 040 020
AMPRO 164
ANAM 122 112 109 106 045
ANSONIC 049 144 145 146 147 148
AOC 128 123 122 037 146 150
APEX 154
ARC EN CIEL 059 056 024 019 017
ARCAM 017
TV Manufacturer/Brand Setup Code Number
BRUNS 088 023
BUSH 092 043 040 020 010
BUSH (UK) 044
CANDLE 128 123
CAPEHART 059
CELLO 178 182
CENTURION 171 123
CENTURY 088 023
CETRONIC 045
CGE 105
CIHAN 032
CITIZEN 132 128 123 045
CLASSIC 045
COBY 104
COMTEL 032
CONCERTO 128
ARISTONA 086 060 048 047 033 025 023 022
ASA 201 096 088 023 012
AUDIOVOX 012 155
AUTOVOX 088 044 025
BANG & OLUFSEN 088
BARCO 202
BASICLINE 020
BAUR 102 077 076 075
BEKO 022
178 171
148 156
165
185
098 109 112 120 138
175
149
150
157
151 152 153 154
158
BENQ 166 170
BLAUPUNKT 084 077 076 075 011
BLU:SENS
BLUE SKY
BRANDT ELECTRONIQUE 059 056 024 019 017
BRION VEGA 203 088 023
BROCKSONIC 206 205 072
174 170
144 155
CONTEC 045 010
CONTINENTAL EDISON 059 056 024 019 017
CORANDO 172
CORONADO 132
CRAIG 159 158 157 045
CROSLEY 088 023
CROWN 132 045
CURTIS MATHES 128 123 132 080 082
CXC 045
132
128
127
119
DAEWOO
DANSAI 022
DAYTRON 132 128
DECCA 091 022
DECCA (UK) 038
DEGRAAF 015
DELL 075
DGM 190
106
105
102
087
116 045
114 022
111 108
37
AVR
Table A10 – Remote Control Product Codes: TV (cont.)
Appendix
TV Manufacturer/Brand Setup Code Number
DIBOSS 186
DIGIFUSION 184
DIGI LINK 200
DIGITREX 192
DISH NETWORK 188
DIXI 022
DORIC 029
DUMONT 201 199 096 088 023
DUMONT-FINLUX 044 012
DYNASTY 045
DYNATECH 063
DYNATRON 022 020
DYNEX 014 083 107 189
ELBE 211 105 095
DYNATRON 022 020
DYNEX 014 083 107 189
ELBE 211 105 095
ELCIT 032 023
ELECTROGRAPH 064
ELECTROHOME 132 115
ELEMENT 048 113
205
162
159
158
157
EMERSON
EMOTION 189
EPSON 074
ERRES 033 022
FENNER 022
FERGUSON
FIDELITY 047
FIDELITY (UK) 099
FINHER 204
FINLANDIA 018
FINLUX 201 199 096 088 044 012
123
197 024
045
126
195
196
099 077 076 075 062 047
001
096
139 088
132 023
128
TV Manufacturer/Brand Setup Code Number
157
FIRST LINE
FISHER 088 043 023
FORGESTONE 099 047
FORMENTI 088
FORMENTI-PHOENIX 088
FUNAI 045 195
FUJITSU 041 042 249 250 195
FUTURETECH 045
GATEWAY 198 199
GBC 043
GE
GEC (UK) 061
GOODMANS 043 022 010 036 041
GORENJE 124 034
GRANADA 104 033 029 022 018 010
GRANADA (UK) 043
GRUNDIG 193 203 200 096 077 076 075 011
GVA 131
HAIER 135 213 028
HALL MARK 128
HANNSPREE 185
HANSEATIC 043 022 020 010
HARMAN KARDON 201
HIFIVOX 080 059 056 024 019 017
HINARI 195 043 020 010
HISENSE 137 140 216
HITACHI
HP 076 218
HUMAX 217 030
HYPER 206
HYPERION 073
159 160 161 163 164 166 168
169
163
159 145 133 128 123 121 087
029
147
144
132
128
123 093 056 012
085 055 010
082 043
080 035
066
026
206 061 024
101 059 018
094 058 015
38
AVR
Table A10 – Remote Control Product Codes: TV (cont.)
Appendix
English
TV Manufacturer/Brand Setup Code Number
HYTEK 016
HYUNDAI 220 236
IKASU 212
ILO 009 056
IMPERIAL 105
INFINITY 148
INKEL 120
INNO HIT 068
INSIGNIA 099 107
INTERFUNK 104 088 056 033 024 023 022 020
121
INTERVISION
ISIS 186
ITT 100 092 046 040
ITT-NOKIA 100 092 058 040
JBL 148
119 118 117 116 115 114 113
111
TV Manufacturer/Brand Setup Code Number
KOGAN 180
KONKA 225
KORTING 088 023
KRIESLER 060 048 047 033 025 023 022
KTV 162 132 123 045
LEVEL 191
132
128
LG (GOLDSTAR)
LINSAR 187
LLOYTRON 173 172
LODGENET 069
LOEWE 227 027
LOEWE OPTA 088 023 022 020
LOGIK 069 099 091 047 038
LUMA 022
LUXMAN 128
022
122 110 101 002 013 086
073
JCPENNY 145 132 128 123 115
JENSEN 019
JET POINT 208
JOHN LEWIS 193
134
JVC
KARCHER 068 012
KATHREIN 124 034
KAWASHO 173
KEC 045
KENMARK 183
KENNEDY 025
KENWOOD 204 123
KLEGG 066
KLH 006
KMC 132
KNEISSEL 105
087 079 092 056 053 047 043
010
LUXOR 058
LXI 148 145 077
M ELECTRONIC 201
MADNADYNE 088 023
MAGNASONIC 015
148
MAGNAVOX
MANESTH 022
MARANTZ 148 123 115 022
MARELLI 088
MARK 022
MARKS & SPENCER 182
MATSUI 148 091 043 040 038 020 001
MAXENT 199
MEDION 031
MEMOREX 128 069
METZ 084 088 077 076 075 023 011
145 132 128 123 030 040 088
138
KNOLL SYSTEMS 224
MGA 128 123 115
39
AVR
Table A10 – Remote Control Product Codes: TV (cont.)
Appendix
TV Manufacturer/Brand Setup Code Number
MINERVA 084 200 096 077 076 075 011
MINTEK 065
MISAKI 195
168
167
160
128
123
115
092
091
090
089
MITSUBISHI
MTC 176 175
MURPHY 021
NATIONAL 182 181 180 179 177 148
NEC 125 123 121 115 010
NECKERMANN 102 088 078 023
NEON 182
NIKEI 045
NOBLEX 204 205
NOKIA 100 092 046 040
NORDMENDE
OKI 045 049 081 087 097
OLEVIA 007
ONKING 045
ONWA 045
OPTOMA 229
OPTONICA 077
ORION
OTTO VERSAND
PANASONIC
PATHE’ MARCONI 059 056 024 019 017
PHILCO
PHILIPS
PHOENIX 088
075
057
029
094 019
211 038
207 022
169 133
148 023
148 033 086 060 025 179
050
023
022
093
080
017
009
210 209 208 207 230 091 040
102
092
020
010
148
087
132
131
132 128 123 115 045 105 088
145
132
089
108
084
078
054
048
023
022
181
213
083
046
043
020
013
069 059 056 053 024
078 077 076 075 043
061
137
130
129
128
123
107
104
071
070
047
046
020
014
082 039 011
043
136 128
036 100 068 033 008
077 079 038 010
018
135 002
035 099 067 032 176
124 076 034 007
134 004
034 095 061 027 177
TV Manufacturer/Brand Setup Code Number
PIONEER 128 123 024 069 056 024 022 020
POLAROID 003 004 005 006 043
PORTLAND 132 128 231
PROLINE 209 020
PROSCAN 133
PROTECH 022
PROTON 165 132 128 122 059 008
200
096
077
QUELLE
QUASAR 087 032
RADIO SHACK 197 196 180 132 128 045
RADIOLA 078 060 048 047 033 025 023 022
RADIOMARELLI 088 083 082 029 023 022
RBM (UK) 044
RCA
REALISTIC 196 167 045
REDIFFUSION 083 082 029
REX 198 025 022
RFT 127 126 125 124 123 122
RTF 023
RUNCO 153 152 044 046
SAA 183
SABA
SALORA 058 018
SAMPO 128 123 059
SAMSUNG
SANYO
SBR 086 084 061 047 046 033 022
SCEPTRE 232
SCHNEIDER
SCOTT 132 128 045 195
SEARS 145 132 128
020
012
163
161
089
188
094
093
023
019
226
145
208
205
054
026 091 092 043 038 023 012
010
196
086 078 060 048 033 025 023
022
076 075 044 038 022
011
145 133 128 123 115 021
088
080
017
132 204
069 059 056 024
009
128
124 022 020 226
068
40
AVR
Table A10 – Remote Control Product Codes: TV (cont.)
Appendix
English
TV Manufacturer/Brand Setup Code Number
SELECO 078 199 198 195 025 022
SHARP 132 128 077 062 092 207 043 010
SHERWOOD 067
SIEMENS 084 077 076 075 015 011 010
SIGNATURE 069
SINGER 105 088 023
SINUDYNE 209 210
SOLE 068 233
212
194
136
130
117
031
028
SONY
SOUND WAVE 020
SOUNDESIGN 128 045
SPECTRICON 122
SSS 045
STERN 198 025 022
SUNKAI 210
SUPERSCAN 195
SUPRATECH 139 140 141 142 143
SYLVANIA
SYMPHONIC 184 195
TANDBERG 080 056 023
TANDY 077
TATUNG 063
TCL 234
TEAC 095 244
TECHNICS 181
TECHWOOD 128
TEKNIKA 132 128 123 115 069 045 195
TELEFUNKEN 069 059 056 024
TELERENT 069
TENSAI 022
TERA 156
093
106
102
091
065
038
016
010
006
148
145 128 123 025 057 094 098
142
172
064 173
062 174
060 043 103
TV Manufacturer/Brand Setup Code Number
191
190
094
093
082
080
074
THOMSON
THORN 099 047
THORN-FERGUSON 196 197 201 103 102 099 047 024
TiVo
TMK 128
TOSHIBA
TOTEVISION 132
TRISTAR 099
TRIUMPH 199 044
TRUTECH 055
UHER 044
ULTRAVOX 088 023
UNIVERSUM 201 102 077 076 075 012
VIDEO CONCEPTS 160
VIDEOCON 188
VIDIKRON 235 253
VIDTECH 128
VIEWSONIC 011 038 047 254 255
VIORE 245 237
VISTRON 194
VISUAL INNOVATIONS 183
VITO 070
VIZIO 001 002 049 050 246
VOXSON 088 023
WARDS 148 132 128 069
WATSON 077 076 075
WEGA 088 043 010
WEGA COLOR 023
WELTBLICK 022
WESTINGHOUSE 017 018 023 060 100 022
WINBOOK 071
069
059
056
053
044
096 037
040
103 010
017
009
005
003
051 052
202
129
063
092
063
043
058 042
024
105 001
072 09
044 162
WINTERNITZ 206
41
AVR
Table A10 – Remote Control Product Codes: TV (cont.) Table A11 – Remote Control Product Codes: DVD (cont.)
Appendix
TV Manufacturer/Brand Setup Code Number
YAMAHA 128 123 238 239
YORK 128
YUPITERU 045
ZANUSSI 198 025 022
ZENITH 090 069 240
ZONDA 122
Table A11 – Remote Control Product Codes: DVD
DVD Manufacturer/Brand Setup Code Number
APEX 033
APEX DIGITAL 061
ARCAM 029
BUSH 070
CALIFORNIA AUDIO 040
COBY 007 013
DENON 051 019 020
DVD Manufacturer/Brand Setup Code Number
PIONEER 065 041 038 018 027
PROCEED 060
PROSCAN 004 103 037
RCA 004 103 037
SAMSUNG 054 053 017 034
SHARP 028 049
SONY 167 045 043 011 012 015 052 057
THOMSON 004 103
TOSHIBA 067 058 009 021 026
XENTA 071
YAMAHA 063 030
ZENITH 064 055 005
ZENITH DIVX 039
Table A12 – Remote Control Product Codes: SAT
SAT Manufacturer/Brand Setup Code Number
DYNEX 014
GE 004 103
HARMAN KARDON 001 002 003 032
INSIGNIA 050 046
JVC 006
KENWOOD 069
KLH 068
LG (GOLDSTAR) 066 064 055 005 010 047
LINN 031
MAGNAVOX 056 022 025
MARANTZ 059
MITSUBISHI 036 023
NAD 062
ONKYO 048 009
PANASONIC 044 035 030 024 008 042
PHILIPS 056 016
AIWA 441
AKAI 333
ALBA 411 301
ALPHASTAR 472
ALPHASTAR DBS 450
ALPHASTAR DSR 442
AMSTRAD 432
ANKARO 421
ASTRO 483 482 481 480 479 478 477 476
BARCOM 421
BIRDVIEW 425
BLAUPUNKT 390 338
BUSH 406 348
BUSH(UK) 353
CANAL 313 378
CANAL DIGITAL 313
42
AVR
Table A12 – Remote Control Product Codes: SAT (cont.)
Appendix
English
SAT Manufacturer/Brand Setup Code Number
CANAL PLUS (CANAL+) 313
CHANNEL MASTER 361 325 321 320
CHAPARRAL 451 316 315
CITOH 360
DIRECTV 302 303 305 309 310 314
DISH NETWORK 364
DRAKE 481 413 318 317 313
DX ANTENNA 483 379 352 331
347
321
325
328
485
484
ECHOSTAR
ELECTRO HOME 392
FERGUSON
FINLUX 310 309
FOXTEL 316 376
FTE 380
FUBA 421 347 314
FUJITSU 334 329 324
GOLDEN INTERSTAR 320
GOODMANS 411
GRUNDIG 390 367 353 338 315 374
HITACHI 411 406 455 304
HOUSTON TRACKER 463
HUGHES 489 437 305 306
HUMAX 307 372
ITT 367
ITT-NOKIA 367
JANIEL 366
JERROLD 484 468 454
KATHREIN 390 380 333 301 410
KCPI 337 380
KOSMOS 380
KYOTO GMI ATLAN 443
LEGEND 453
463
424 348
453
397
395
364
411
406 367 364 363 353 352
345
308
478 338
477 340
SAT Manufacturer/Brand Setup Code Number
LEMON 474
LOEWE 475
LORENZEN 474 465 464 463 461
MACOM 371 370 369 365 317
MAGNAVOX 473 461
MARANTZ 333
MASPRO 406 353
MEMOREX 453
METZ 390
MINERVA 390
MITSUBISHI 390 307
MOTOROLA 312 319
MULTISTAR 380
NEC 373 346 336 330
NETA P562 440
NEXTWAVE 423
NOKIA 367
NORSAT 346 373
OPTIMUS 466
OTTO VERSAND 390
424
367
364
363
PACE
PACE MSS SERIES 367
PANASONIC 424 331 469 366 457 353
PANSAT 420
PERSONAL CABLE 418
PHILIPS 424 421 353 333 332 319 375
PICO 407
PREMIERE 308 357
PRESIDENT 404 381
PRIMESTAR 475 468 454 412 302
QUADRAL 473 472 471 470 469 468 467 466
QUELLE 390
487
328
343
353 348 317 339
382
43
AVR
Appendix
Table A12 – Remote Control Product Codes: SAT (cont.)
SAT Manufacturer/Brand Setup Code Number
RADIOLA 353
RADIX 347
RCA 335 490 465 439 301 458 358 367
REALISTIC 480 349
SAMSUNG 432 427 380 334 442 322 326 345
SAT 427
SATELLITE SERVICE 388 335
SCIENTIFIC ATLANTA 339 356
SCHNEIDER 353
SIEMENS 390 338
SKY 306 317 318 343 344
SKY MASTER 433
SKYLAB 421
SONY 329 405 362 341
STAR CHOICE DBS 459
STARCAST 347
SUPER GUIDE 423 327
TECHNISAT 347
TEECOM 409 393 391 390 333 330
TELECOM 341
TELEFUNKEN 383
THORN-FERGUSON 367 364 348 363 353 352 345 323
TOPFIELD 311 363
TOSHIBA 470 462 461 460 426 302
480
479
466
403
389
381
UNIDEN
VIASAT 312 377
VORTEC 442 432
WISI 427 347 326 327 322 304
ZEHNDER 427 380
ZENITH 344 488 419 394 387 385 384 359
351
350
349
348
332
355 354
323
Table A13 – Remote Control Product Codes: Cable
Cable Manufacturer/Brand Setup Code Number
ABC 011 001
ALLEGRO 111
AMERICAST 212
AMINO 015 031
ARCHER 112
BELCOR 113
BT CABLE 007
CABLE STAR 113 033
CABLETIME 016 012 011 008
CISCO 016 021 032 033
CITIZEN 111
CLYDE CABLE VISION 017
COLOUR VOICE 090 085
COMCAST 007 040 054
DESCAT CANAL 010
DIGI LINK 114
EAGLE 186
EASTERN 070 066
ELECTRICORD 039
EMERSON 112
FILMNET 020 018
FOCUS 116
FOXTEL 043
FRANCE TELECOM 021 013
GEC
G.I 097 096 017 011 001
GC ELETRONICS 113
GEMINI 060 032
GENERAL 210
GENERAL INSTRUMENT 210 054 040
019
017
015
014
GOODMIND 112
HANLIN 208 175 117 101 100 099 056
44
AVR
Table A13 – Remote Control Product Codes: Cable (cont.)
Appendix
English
Cable Manufacturer/Brand Setup Code Number
HITACHI 188 001
JASCO 111
210
188
JERROLD
LINSAY 118
MACOM 191
MAGNAVOX 068 019 017
MOTOROLA 022 023 026 031 034 035 036 038
MOVIE TIME 039 035
NSC 190 035
OAK 220 197
PACE 179
PANASONIC 214 189 177 176 053
PANTHER 114
PHILIPS 090 085 020 019 013 023
PIONEER 216 215 209 171 119 041 001 002
POPULAR MECHANIC 116
PRELUDE 120
PRIMESTAR 162
002
162 097 096 073 017 011
001
Cable Manufacturer/Brand Setup Code Number
STARGATE 120
TANDY 024
TELECAPATION 028
TELESERVICE 011
TEXSCAN 036
TFC 122
TIMELESS 123
TiVo 029 030
TOCOM 205 170
TUDI 027
UNITED CABLE 011 001
UNIVERSAL 113 042 039 034 033
VIDEOWAY 211 124
VISIOPASS 009
VIEWSTAR 190 089 086 053 025 019
WESTMINSTER CABLE 007
ZENITH 219 211 125 065
ZENTEK 116
QUEST 037 041
RADIOSHACK 213 112 111
RCA 214 053
RECOTON 116
REGAL 208 101 100 099 056
REMBRANT 032
SAGEM 028
SAMSUNG 003 186 072 002 024
SATBOX 004
222
221
SCIENTIFIC ATLANTA
SEAM 121
SIGNATURE 188 001
SPRUCER 189 177 081 053
STARCOM 163 011 002
006
203 183 038 039 026 025
005
Table A14 – Remote Control Product Codes: Game Console
Game Console/Brand Setup Code Number
MS (X-BOX, XBOX360) 001 003
NYKO (PS3) 005
SONY (PS2, PS3) 002 004
Table A15 – Remote Control Product Codes: Music Server
Music Server/Brand Setup Code Number
APPLE 008 009 014
ASUS 016
BEYOND 003
ESCIENT (FIREBALL) 004 005 006 007
HARMAN KARDON 001 002
45
AVR
Appendix
Table A15 – Remote Control Product Codes: Music Server (cont.)
Music Server/Brand Setup Code Number
IOMEGA 022 023
LOGITECH 012
MICROSOFT 003
NAIM 011
NETGEAR 020 021
NIXEUS 024
REQUEST 010
ROKU 015
SONOS 013
SONY 017 018
WESTERN DIGITAL 019
Table A16 – Remote Control Product Codes: DVR
DVR/Brand Setup Code Number
DAEWOO 004 001
ECHOSTAR 016 015 014
EXPRESSVU 014
Table A17 – Remote Control Product Codes: TiVo
TiVo/Brand Setup Code Number
TiVo Series2™ DT DVR 302
TiVo HD DVR 304
TiVo HD XL DVR 310
TiVo Series3 309
TiVo Series4 309
PREMIERE 309
DIRECTV TiVo 306 312
PIONEER TiVo 301
TOSHIBA TiVo 303
HUMAX TiVo 303
COMCAST TiVo 311
Nero LiquidTV TiVo 303
RCN TiVo 309
SUDDENLINK TiVo 309
ONO TiVo 309
VIRGIN MEDIA TiVo 313
OTHER TiVo 305 307 308
HUGHES 027 017
HYUNDAI 018
KEEN 009
PANASONIC 023 010
PHILIPS 024 017 011 027
PROSCAN 019
RCA 019 027
REPLAYTV 026 025 012 010 008
SONICBLUE 012 010
SONY 024 023 022 021 020 013 007
46
HARMAN International Industries, Incorporated 8500 Balboa Boulevard, Northridge, CA 91329 USA
© 2012 HARMAN International Industries, Incorporated. All rights reserved.
Harman Kardon and Logic 7 are trademarks of HARMAN International Industries, Incorporated, registered in the United States and/or
other countries. EzSet/EQ is a trademark of HARMAN International Industries, Incorporated. AirPlay, Apple, iPad, iPhone, iPod, iTunes
and Mac are trademarks of Apple Inc., registered in the U.S. and other countries. Blu-ray Disc is a trademark of the Blu-ray Disc Asso­ciation. DLNA is a registered trademark of the Digital Living Network Alliance. Dolby and Pro Logic are registered trademarks of Dolby Laboratories. MLP Lossless is a trademark of Dolby Laboratories. DTS is a registered trademark, and DTS 96/24, DTS-HD and DTS-HD Master Audio and DTS Neo:6 are trademarks of DTS, Inc. HDMI is a registered trademark of HDMI Licensing LLC in the United States and other countries. Intel is a registered trademark of Intel Corporation. iOS is a registered trademark of Cisco Systems, Inc., and/or its affiliates in the United States and certain other countries. TiVo is a registered trademark of TiVo Inc. Series2 is a trademark of TiVo Inc. vTuner is a trademark of Nothing Else Matters Software, Ltd., Inc. Wi-Fi is a registered trademark of the Wi-Fi Alliance. Windows Media is a registered trademark of Microsoft Corporation in the United States and/or other countries.
Features, specifications and appearance are subject to change without notice.
HKP4052 Rev: A
www.harmankardon.com
Loading...