Loading...
GA-J1800M-D2P GA-J1900M-D2P
User's Manual
Rev. 1101
12ME-J18MD2P-1101R
GA-J1800M-D2P GA-J1900M-D2P
Motherboard
GA-J1800M-D2P/GA-J1900M-D2P
Motherboard
GA-J1800M-D2P
GA-J1900M-D2P
Aug. 15, 2014
Aug. 15, 2014
Copyright
© 2014 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.
Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
ChangestothespecificationsandfeaturesinthismanualmaybemadebyGIGABYTEwithoutpriornotice.
No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission.
In order to assist in the use of this product, carefully read the User's Manual.
For product-related information, check on our website at: http://www.gigabyte.com
Identifying Your Motherboard Revision
The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0" means the revision of the motherboard is 1.0. Check your motherboard revision before updating motherboard BIOS,
drivers, or when looking for technical information. Example:
Table of Contents
GA-J1800M-D2P/GA-J1900M-D2P Motherboard Layout............................................... |
4 |
|
GA-J1800M-D2P/GA-J1900M-D2P Motherboard Block Diagram.................................. |
5 |
|
Chapter 1 Hardware Installation...................................................................................... |
6 |
|
1-1 |
Installation Precautions.................................................................................... |
6 |
1-2 |
Product Specifications..................................................................................... |
7 |
1-3 |
Installing the Memory....................................................................................... |
9 |
1-4 |
Installing an Expansion Card........................................................................... |
9 |
1-5 |
Back Panel Connectors.................................................................................... |
9 |
1-6 |
Internal Connectors......................................................................................... |
11 |
Chapter 2 BIOS Setup................................................................................................... |
16 |
|
2-1 |
Startup Screen............................................................................................... |
16 |
2-2 |
Main................................................................................................................ |
17 |
2-3 |
Advanced........................................................................................................ |
18 |
2-4 |
Chipset........................................................................................................... |
22 |
2-5 |
Security.......................................................................................................... |
23 |
2-6 |
Boot................................................................................................................ |
25 |
2-7 |
Save & Exit..................................................................................................... |
26 |
Chapter 3 Appendix....................................................................................................... |
27 |
|
Drivers Installation..................................................................................................... |
27 |
|
Regulatory Statements.............................................................................................. |
28 |
|
Contact Us................................................................................................................. |
32 |
|
- 3 -
GA-J1800M-D2P/GA-J1900M-D2P Motherboard Layout
KB_MS_USB
DDR3_1
VGA |
|
M_BIOS |
GA-J1800M-D2P |
|
|
|
|
|
|||
|
|
GA-J1900M-D2P |
|
||
|
|
ATX_12V |
|
||
|
LPT |
|
|
|
|
HDMI |
|
|
|
|
|
|
|
|
|
Intel® J1800 SoC j |
|
|
|
|
|
Intel® J1900 SoC k |
|
|
|
BAT |
|
|
|
USB30 |
|
|
CPU_FAN |
|
|
|
|
|
CI |
|
|
|
|
|
|
|
|
USB_LAN |
|
iTE® |
SATA2 |
||
|
Super I/O |
||||
|
|
Realtek® |
|
0 |
1 |
|
|
|
|
|
|
|
|
GbE LAN |
|
|
|
AUDIO |
SPDIF_O COMA |
COMB |
F_USB1 |
F_USB2 |
|
|
|
||||
|
|
F_AUDIO |
|
|
|
|
|
|
|
PCIe to PCI |
SYS_FAN |
|
|
PCIEX1 |
|
Bridge |
|
|
|
PCI |
|
|
|
|
|
CODEC |
|
|
|
ATX
2_ DDR3 F_PANEL
CLR_CMOS
Box Contents
55 |
GA-J1800M-D2P or GA-J1900M-D2P motherboard |
||
55 |
Motherboard driver disk |
55 |
Two SATA cables |
55 |
User's Manual |
55 |
I/O Shield |
The box contents above are for reference only and the actual items shall depend on the product package you obtain. The box contents are subject to change without notice.
MM Only for GA-J1800M-D2P. NN Only for GA-J1900M-D2P.
- 4 -
GA-J1800M-D2P/GA-J1900M-D2P Motherboard Block Diagram
|
|
|
|
|
|
|
|
DDR3/-L 1333 MHz |
|
|
|
|
HDMI |
|
|
|
Dual Channel Memory |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
D-Sub |
|
|
|
BIOS |
|
|
|
1 PCI Express x1 |
|
|
|
|
2 SATA 3Gb/s |
|||
|
|
|
|
|
|
|
|
||
|
|
|
Intel® J1800 SoC j |
|
1 USB 3.0/2.0 |
||||
|
|
|
Intel® J1900 SoC k |
|
|
|
|
||
PCI Express Bus |
x1 |
|
|
|
|
8 USB 2.0/1.1 |
|||
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
||
|
|
x1 |
x1 |
|
|
|
|
|
|
PCIe CLK |
Realtek® |
PCIe to PCI |
|
|
LPC |
|
|
COM |
|
(100 MHz) |
|
|
|
|
|
||||
|
GbE LAN |
Bridge |
|
|
Bus |
iTE® |
|
LPT |
|
|
|
|
|
|
|
|
Super I/O |
||
|
|
|
|
|
|
|
|
||
|
|
RJ45 |
|
|
|
|
|
|
PS/2 KB/Mouse |
|
|
LAN |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PCI Bus |
|
|
|
|
|
|
|
|
|
|
|
|
|
CODEC |
|
|
|
|
|
PCI CLK |
|
|
(Center/SubwooferMIC |
Speaker(FrontOutLineOut) Speaker(RearInLineOut) |
S/PDIFOut |
|
|
|
|
|
|
|
|
|
|
|
|||
(33 MHz) |
|
|
Out) Speaker |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 PCI |
|
|
|
|
|
|
|
MM Only for GA-J1800M-D2P.
NN Only for GA-J1900M-D2P.
For detailed product information/limitation(s), refer to "1-2 Product Specifications."
- 5 -
Chapter 1 Hardware Installation
1-1 Installation Precautions
The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's manual and follow these procedures:
•• Prior to installation, make sure the chassis is suitable for the motherboard.
•• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or warranty sticker provided by your dealer. These stickers are required for warranty validation.
•• Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components.
•• When connecting hardware components to the internal connectors on the motherboard, make sure they are connected tightly and securely.
•• When handling the motherboard, avoid touching any metal leads or connectors.
•• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap, keep your hands dry and first touch a metal object to eliminate static electricity.
•• Prior to installing the motherboard, please have it on top of an antistatic pad or within an electrostatic shielding container.
•• Before unplugging the power supply cable from the motherboard, make sure the power supply has been turned off.
•• Before turning on the power, make sure the power supply voltage has been set according to the local voltage standard.
•• Before using the product, please verify that all cables and power connectors of your hardware components are connected.
•• To prevent damage to the motherboard, do not allow screws to come in contact with the motherboard circuit or its components.
•• Make sure there are no leftover screws or metal components placed on the motherboard or within the computer casing.
•• Do not place the computer system on an uneven surface.
•• Do not place the computer system in a high-temperature environment.
•• Turning on the computer power during the installation process can lead to damage to system components as well as physical harm to the user.
•• If you are uncertain about any installation steps or have a problem related to the use of the product, please consult a certified computer technician.
- 6 -
1-2 Product Specifications
CPU |
|
Built in with an Intel® Dual-Core Celeron® J1800 |
SoC (2.41 GHz) j |
|
|
Built in with an Intel® Dual-Core Celeron® J1900 |
SoC (2.0 GHz) k |
*Do not disassemble the onboard SoC and the heatsinks by yourself to avoid damage to these components.
|
1 MB Cache j |
|
|
2 MB Cache k |
|
Memory |
2 x DDR3 DIMM sockets supporting up to 16 GB of system memory |
|
|
|
* Due to a Windows 32-bit operating system limitation, when more than 4 GB of physical |
|
|
memory is installed, the actual memory size displayed will be less than the size of |
|
|
the physical memory installed. |
|
Dual channel memory architecture |
|
|
Support for DDR3/-L 1333 MHz memory modules |
|
|
Support for non-ECC memory modules |
|
Onboard |
Integrated in the SoC: |
|
Graphics |
- |
1 x D-Sub port, supporting a maximum resolution of 2560x1600 |
-1 x HDMI port, supporting a maximum resolution of 1920x1080
Audio |
|
Realtek® ALC887 codec |
|
High Definition Audio |
|
|
|
2/4/5.1/7.1-channel |
*To configure 7.1-channel audio, you have to use an HD front panel audio module and enable the multi-channel audio feature through the audio driver.
Support for S/PDIF Out
LAN |
|
Realtek® GbE LAN chip (10/100/1000 Mbit) |
Expansion Slots |
|
1 x PCI Express x1 slot |
|
|
1 x PCI slot |
Storage Interface |
|
Integrated in the SoC: |
|
|
- 2 x SATA 3Gb/s connectors |
USB |
|
Integrated in the SoC: |
|
|
- 1 x USB 3.0/2.0 port on the back panel |
|
|
- 8 x USB 2.0/1.1 ports (4 ports on the back panel, 4 ports available through |
|
|
the internal USB headers) |
Internal
Connectors
1 x 24-pin ATX main power connector1 x 4-pin ATX 12V power connector2 x SATA 3Gb/s connectors
1 x CPU fan header1 x system fan header1 x front panel header
1 x front panel audio header1 x S/PDIF Out header
2 x USB 2.0/1.1 headers2 x serial port headers
1 x chassis intrusion header1 x Clear CMOS jumper
MM Only for GA-J1800M-D2P.
NN Only for GA-J1900M-D2P.
- 7 -
Back Panel
Connectors
1 x PS/2 keyboard/mouse port1 x D-Sub port
1 x HDMI port1 x parallel port
1 x USB 3.0/2.0 port4 x USB 2.0/1.1 ports1 x RJ-45 port
3 x audio jacks (Line In, Line Out, Mic In)
I/O Controller |
iTE® I/O Controller Chip |
Hardware
Monitor
System voltage detection
CPU/System temperature detectionCPU/System fan speed detectionCPU/System fan speed control
*Whether the fan speed control function is supported will depend on the cooler you install.
BIOS |
|
1 x 64 Mbit flash |
|
Use of licensed AMI UEFI BIOS |
|
|
|
PnP 1.0a, DMI 2.7, WfM 2.0, SM BIOS 2.7, ACPI 5.0 |
Unique Features Support for Xpress InstallSupport for @BIOS
Support for APP Center
*Available applications in APP Center may differ by motherboard model. Supported functions of each application may also differ depending on motherboard specifications.
Support for ON/OFF Charge
Bundled |
Norton® Internet Security (OEM version) |
|
Software |
Intel® Smart Connect Technology |
|
Operating |
Support for Windows 8.1/8/7 |
|
System |
||
|
||
Form Factor |
Micro ATX Form Factor; 19.0cm x 18.0cm |
*GIGABYTE reserves the right to make any changes to the product specifications and product-related information without prior notice.
*Please visit the Support & Downloads\Utility page on GIGABYTE's website to check the supported operating system(s) for the software listed in the "Unique Features" and "Bundled Software" columns.
- 8 -
1-3 Installing the Memory
Read the following guidelines before you begin to install the memory:
•• Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips be used.
(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)
•• Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage.
•• Memory modules have a foolproof design. A memory module can be installed in only one direction. If you are unable to insert the memory, switch the direction.
Dual Channel Memory Configuration
This motherboard provides two DDR3 memory sockets and supports Dual Channel Technology. After the memory is installed, the BIOS will automatically detect the specifications and capacity of the memory. Enabling Dual
Channel memory mode will double the original memory bandwidth.
The two DDR3 memory sockets are divided into two channels and each channel has one memory socket as following:
Channel A: DDR3_1Channel B: DDR3_2
Due to SoC limitations, read the following guidelines before installing the memory in Dual Channel mode.
1.If only one DDR3 memory module is to be installed, be sure to install it in the DDR3_1 socket, and Dual Channel mode cannot be enabled if only one memory module is installed.
2.When enabling Dual Channel mode with two memory modules, it is recommended that memory of the same capacity, brand, speed, and chips be used for optimum performance.
1-4 Installing an Expansion Card
Read the following guidelines before you begin to install an expansion card:
•• Make sure the motherboard supports the expansion card. Carefully read the manual that came with your expansion card.
•• Always turn off the computer and unplug the power cord from the power outlet before installing an expansion card to prevent hardware damage.
1-5 Back Panel Connectors
USB 2.0/1.1 Port
The USB port supports the USB 2.0/1.1 specification. Use this port for USB devices such as a USB keyboard/mouse, USB printer, USB flash drive and etc.
PS/2 Keyboard/Mouse Port
Use this port to connect a PS/2 mouse or keyboard.
Parallel Port
Use the parallel port to connect devices such as a printer, scanner and etc. The parallel port is also called a printer port.
- 9 -
D-Sub Port
The D-Sub port supports a 15-pin D-Sub connector and supports a maximum resolution of 2560x1600 (the actual resolutions supported depend on the monitor being used). Connect a monitor that supports D-Sub connection to this port.
HDMI Port
The HDMI port is HDCP compliant and supports Dolby True HD and DTS HD
Master Audio formats. It also supports up to 192KHz/24bit 8-channel LPCM audio output. You can use this port to connect your HDMI-supported monitor. The maximum supported resolution is 1920x1080, but the actual resolutions supported are dependent on the monitor being used.
After installing the HDMI device, make sure to set the default sound playback device to HDMI.
Dual Display Configurations for the Onboard Graphics:
Dual-display configurations are supported after you install motherboard drivers in OS, but not during the
BIOS Setup or POST process.
USB 3.0/2.0 Port
The USB 3.0 port supports the USB 3.0 specification and is compatible to the USB 2.0/1.1 specification. Use this port for USB devices such as a USB keyboard/mouse, USB printer, USB flash drive and etc.
RJ-45 LAN Port
The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following describes the states of the LAN port LEDs.
Connection/ |
|
|
|
|
|
|
|
|
Connection/Speed LED: |
|
Activity LED: |
|
|||||||
Speed LED |
|
|
|
Activity LED |
|
|
|||||||||||||
|
|
|
|
|
|
|
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
State |
Description |
|
State |
Description |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Orange |
1 Gbps data rate |
|
Blinking |
Data transmission or receiving is occurring |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Green |
100 Mbps data rate |
|
Off |
No data transmission or receiving is occurring |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Off |
10 Mbps data rate |
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
LAN Port |
|
|
|
||||||||||||
|
|
|
|
|
|
|
|
|
|||||||||||
Line In Jack (Blue)
The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.
Line Out Jack (Green)
The line out jack. Use this audio jack for a headphone or 2-channel speaker. This jack can be used to connect front speakers in a 4/5.1/7.1-channel audio configuration.
Mic In Jack (Pink)
The Mic in jack. Microphones must be connected to this jack.
To configure 7.1-channel audio, you have to use an HD front panel audio module and enable the multi-channel audio feature through the audio driver.
•• When removing the cable connected to a back panel connector, first remove the cable from your device and then remove it from the motherboard.
•• When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent an electrical short inside the cable connector.
- 10 -
Loading...