If your Timer looks like this, use the following instructions
If your Timer does not look like this, go to the next page
Digital Timer |
DISPLAY SHOWN IN STANDARD “CLOCK” MODE DISPLAY. |
||
|
|
||
|
CLOCK (DST) |
|
HOUR (RND) |
|
- To set time/day, hold down CLOCK and |
- While holding CLOCK button, press to set hour (time). |
|
|
press HOUR>MINUTE>DAY buttons. |
- While in programming mode, press to set hour for ON/OFF times. |
|
|
- In clock mode, hold down for 5 sec. to |
- While in clock mode, press and hold (3 sec.) to activate random |
|
|
move forward or back an hour (Daylight |
security feature. |
|
|
Savings Adjust). |
|
MINUTE |
|
|
|
|
|
|
|
- While holding CLOCK button, press to set minute (time). |
|
|
|
- While in programming mode, press to set minute for ON/OFF times. |
|
PROGRAM |
|
DAY |
|
Press to enter timer programming mode. |
- While holding CLOCK button, press to set day of week. |
|
|
|
RESET |
- While in programming mode, press to scroll through options |
|
RCL |
|
for days of the week. |
|
In programming mode, press to cancel or |
ON/OFF (push to scroll) |
|
|
restore ON/OFF time shown. |
|
|
|
|
ON= Always ON |
|
|
|
|
|
|
|
|
Auto ON/OFF = Timer is active |
|
|
|
OFF = Always OFF |
|
|
PRESS AND HOLD TO RESET ALL THE |
|
|
|
PROGRAMS PERMANENTLY |
|
Initial Set Up: |
|
Figure 1 |
7. Press "PROGRAM" to move onto Program 2 (P2ON) and repeat steps |
|
|
||
1. If the LCD screen is displaying numbers, you are ready to program, please |
1-6 if you want to program additional ON/OFF times, or press "CLOCK" |
||
proceed to step 2. If the screen is blank plug in the timer and leave for two |
(at anytime) to finish programming. You can prgram up to 20 ON/OFF |
||
hours to charge internal battery before programming. |
programs to run simultaneously! |
||
2. Use a toothpick or sharp pencil to push the RESET button. Once pushed, |
8. Once programming is complete, pressing "CLOCK" returns you |
||
the screen will go blank briefly and then display 12:00 AM. See Figure 2. |
to "clock mode." |
||
|
|
|
9. Once all programming is complete make sure lamp or device is set in the |
Setting the Time: |
|
|
ON position. Plug the light or device into the timer and plug the timer into |
1. Press and hold down the “CLOCK” button through the time and day setting |
the wall. Your timer is ready to use! |
||
Figure 2 |
LCD display |
Ready to set |
|
Note: The lamp or device will not come on until the next ON time is triggered. To manually turn the device ON and start the program, cycle the ON/OFF button until the light/device turns on and the display reads AUTO ON. You can also use the ON/OFF button to override the timer and set to ON (always on) or OFF (always off).
process.
2.Holding “CLOCK” button down, press the “HOUR” button until the current hour is found. Take note of AM/PM in bottom right of display. See Figure 1.
3.Press the “MINUTE” button, keeping the “CLOCK” button depressed. Continue to press the “MINUTE” button until the current minute is found.
4.Press the “DAY” button, keeping the “CLOCK” button depressed. Continue to press the “DAY” button until the current day is found.
5.When current day is found release "CLOCK" button.
Programming ON/OFF Times:
Note: While programming, if no button is pushed for 10 seconds the timer will return to the clock display.
1.Press & release the “PROGRAM” button to start programming. The screen will show 1ON and all of the days of the week. See
Figure 3
2.Press ”DAY” to scroll through the options for the days of the week you want to program:
•MO TU WE TH FR SA SU
•MO>TU>WE>TH>FR>SA>SU (to show every single day of the week one by one, which means the on/off setting is only activated on this selected day)
•MO TU WE TH FR
•SA SU
•MO TU WE TH FR SA
•MO WE FR
•TU TH SA
•MO TU WE
•TH FR SA
3.Find the days that you would like the timer to function and stop pushing the “DAYS” button leaving the days you want the timer to function showing on the display.
4.Press the “HOUR” button until the hour you want the timer to activate is showing on the display. (The AM and PM is displayed in the lower right hand corner of the display. Make sure it is correct when setting the time).
5.Press the “MINUTE” button until the minute you want the timer to activate is showing on the display.
6.Press & release “PROGRAM” to set the 1OFF time. Repeat steps 1 -5 to program when you want the timer to turn OFF for program 1.
Remarks:
1.While in programming mode, the programmed time can be cancelled or resumed by pressing the “RECALL” (RCL) button.
2.ON/OFF time becomes effective immediately once the setting is done.
3.Light/Device must be turned ON when plugged into timer or timer will not control the appliance.
ON/OFF Options:
There are 4 settings for the timer; Press the “ON/OFF” button to scroll through the options and stop at the option desired.
a.ON – Timer outlet is always ON (Overrides Programming).
b.AUTO ON – Timer outlet is currently ON and will turn OFF at next programmed OFF time.
c.OFF – Timer outlet is always OFF (Overrides Programming).
d.AUTO OFF – Timer outlet is currently OFF and will turn on at the next programmed ON time.
The timer program will control the appliance if set to AUTO ON or AUTO OFF.
Random Security Option (RND):
This program option will turn lights ON and OFF using the programmed times + or - 30 minutes, giving the home a more lived in appearance while occupant is away.
1.Press the “HOUR” (RND) button for 5 seconds to activate the random feature. The display will show the RND icon above the seconds on the display. See Figure 1.
2.Press the “HOUR” (RND) button for 5 seconds to deactivate the random feature. The display will not show the RND icon. See Figure 1.
Daylight Savings Time (DST) Easy Adjust Feature:
Push the “CLOCK” button for 5 seconds to advance the current time 1 hour, +1h icon should appear on the lower left corner of the display. Repeating this process will decrease the time by 1 hour and the +1h icon will disappear.
See Figure 1.
15089
4-2011 www.jascoproducts.com
Loading...